PCI: pciehp: Ignore Link Down/Up caused by DPC

PCI: pciehp: Ignore Link Down/Up caused by DPC

Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.

A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery.  That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver.  DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.

Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC:  Power off/on is a cold reset concurrently to DPC's warm
reset.  Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.

Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so.  On successful recovery, ignore both the Link Down and the
subsequent Link Up event.

Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery.  Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().

The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other.  If pciehp is faster than DPC, it
will wait until DPC recovery completes.

Recovery consists of two steps:  The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit.  The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.

If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.

pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot.  This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.

The timeout is necessary because the DPC Trigger Status bit may never
clear:  On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery.  Without the timeout, pciehp would then wait indefinitely for DPC
to complete.

This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:

By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/

By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/

By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/

Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>