The open-coded mutex implementation for ARMv6+ cores suffers from a
severe lack of barriers, so in the uncontended case we don't actually
protect any accesses performed during the critical section.
Furthermore, the code is largely a duplication of the ARMv6+ atomic_dec
code but optimised to remove a branch instruction, as the mutex fastpath
was previously inlined. Now that this is executed out-of-line, we can
reuse the atomic access code for the locking (in fact, we use the xchg
code as this produces shorter critical sections).
This patch uses the generic xchg based implementation for mutexes on
ARMv6+, which introduces barriers to the lock/unlock operations and also
has the benefit of removing a fair amount of inline assembly code.
Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Reported-by: Shan Kang <kangshan0910@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running on 32bit the mce handler could misinterpret
vm86 mode as ring 0. This can affect whether it does recovery
or not; it was possible to panic when recovery was actually
possible.
Fix this by always forcing vm86 to look like ring 3.
[ Backport to 3.0 notes:
Things changed there slightly:
- move mce_get_rip() up. It fills up m->cs and m->ip values which
are evaluated in mce_severity(). Therefore move it up right before
the mce_severity call. This seem to be another bug in 3.0?
- Place the backport (fix m->cs in V86 case) to where m->cs gets
filled which is mce_get_rip() in 3.0
]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
try_to_wake_up() has a problem which may change status from TASK_DEAD to
TASK_RUNNING in race condition with SMI or guest environment of virtual
machine. As a result, exited task is scheduled() again and panic occurs.
Here is the sequence how it occurs:
----------------------------------+-----------------------------
|
CPU A | CPU B
----------------------------------+-----------------------------
TASK A calls exit()....
do_exit()
exit_mm()
down_read(mm->mmap_sem);
rwsem_down_failed_common()
set TASK_UNINTERRUPTIBLE
set waiter.task <= task A
list_add to sem->wait_list
:
raw_spin_unlock_irq()
(I/O interruption occured)
__rwsem_do_wake(mmap_sem)
list_del(&waiter->list);
waiter->task = NULL
wake_up_process(task A)
try_to_wake_up()
(task is still
TASK_UNINTERRUPTIBLE)
p->on_rq is still 1.)
schedule()
(exit task is running again)
BUG_ON() is called!
--------------------------------------------------------
The execution time between (*A) and (*B) is usually very short,
because the interruption is disabled, and setting TASK_RUNNING at (*C)
must be executed before setting TASK_DEAD.
HOWEVER, if SMI is interrupted between (*A) and (*B),
(*C) is able to execute AFTER setting TASK_DEAD!
Then, exited task is scheduled again, and BUG_ON() is called....
If the system works on guest system of virtual machine, the time
between (*A) and (*B) may be also long due to scheduling of hypervisor,
and same phenomenon can occur.
By this patch, do_exit() waits for releasing task->pi_lock which is used
in try_to_wake_up(). It guarantees the task becomes TASK_DEAD after
waking up.
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed spi device initialization of dev.parent pointer
to be the master's device pointer instead of his parent.
This introduced a bug in spi-fsl-spi, since its usage of spi device
pointer was not updated accordingly. This was later fixed by commit 5039a86, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed
another spot on fsl_spi_cs_control function where we also need to update
usage of spi device pointer. This change address that.
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed device initialization to be children of the
bus master, not children of the bus masters parent device. The pdata
pointer used in fsl_spi_chipselect must updated to reflect the changed
initialization.
UBI was mistakingly using 'kfree()' instead of 'kmem_cache_free()' when
freeing "attach eraseblock" structures in vtbl.c. Thankfully, this happened
only when we were doing auto-format, so many systems were unaffected. However,
there are still many users affected.
It is strange, but the system did not crash and nothing bad happened when
the SLUB memory allocator was used. However, in case of SLOB we observed an
crash right away.
This problem was introduced in 2.6.39 by commit
"6c1e875 UBI: add slab cache for ubi_scan_leb objects"
Reported-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASPM on the 82574 causes trouble. Currently the driver disables L0s for
this NIC but only disables L1 if the MTU is >1500. This patch simply
causes L1 to be disabled regardless of the MTU setting.
Signed-off-by: Chris Boot <bootc@bootc.net> Cc: "Wyborny, Carolyn" <carolyn.wyborny@intel.com> Cc: Nix <nix@esperi.org.uk> Link: https://lkml.org/lkml/2012/3/19/362 Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com> Acked-by: Arindam Nath <arindam.nath@amd.com> Acked-by: Philip Rakity <prakity@marvell.com> Acked-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.
This patch adds enable/disable rx error interrupt code.
For some reason, when the lirc daemon learns that a usb remote control
has been unplugged, it wants to read the sysfs attributes of the
disappearing device. This is useful for uncovering transient
inconsistencies, but less so for keeping the system running when such
inconsistencies exist.
Under some circumstances (like every time I unplug my dvb stick from
my laptop), lirc catches an rc_dev whose raw event handler has been
removed (presumably by ir_raw_event_unregister), and proceeds to
interrogate the raw protocols supported by the NULL pointer.
This patch avoids the NULL dereference, and ignores the issue of how
this state of affairs came about in the first place.
Version 2 incorporates changes recommended by Mauro Carvalho Chehab
(-ENODEV instead of -EINVAL, and a signed-off-by).
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If update_wall_time() is called and the current offset isn't large
enough to accumulate, avoid re-calling timekeeping_adjust which may
change the clock freq and can cause 1ns inconsistencies with
CLOCK_REALTIME_COARSE/CLOCK_MONOTONIC_COARSE.
Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1345595449-34965-5-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unexpected behavior could occur if the time is set to a value large
enough to overflow a 64bit ktime_t (which is something larger then the
year 2262).
Also unexpected behavior could occur if large negative offsets are
injected via adjtimex.
So this patch improves the sanity check timekeeping inputs by
improving the timespec_valid() check, and then makes better use of
timespec_valid() to make sure we don't set the time to an invalid
negative value or one that overflows ktime_t.
Note: This does not protect from setting the time close to overflowing
ktime_t and then letting natural accumulation cause the overflow.
Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1344454580-17031-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework the logic to call the sleeping functions in right context.
Use standard timer/workqueue api to let system chose any cpu to perform
the allocation and netlink send.
Also avoid a loop if reset_per_cpu_data() cannot allocate memory :
use mod_timer() to wait 1/10 second before next try.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I just noticed after some recent updates, that the init path for the drop
monitor protocol has a minor error. drop monitor maintains a per cpu structure,
that gets initalized from a single cpu. Normally this is fine, as the protocol
isn't in use yet, but I recently made a change that causes a failed skb
allocation to reschedule itself . Given the current code, the implication is
that this workqueue reschedule will take place on the wrong cpu. If drop
monitor is used early during the boot process, its possible that two cpus will
access a single per-cpu structure in parallel, possibly leading to data
corruption.
This patch fixes the situation, by storing the cpu number that a given instance
of this per-cpu data should be accessed from. In the case of a need for a
reschedule, the cpu stored in the struct is assigned the rescheule, rather than
the currently executing cpu
Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections. Specifically, its possible to replace data->skb while its
being written. This patch corrects that by making data->skb an rcu protected
variable. That will prevent it from being overwritten while a tracepoint is
modifying it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: David Miller <davem@davemloft.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: David Miller <davem@davemloft.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For one, the driver device pointer needs to be filled in, or the lirc core
will refuse to load the driver. And we really need to wire up all the
platform_device bits. This has been tested via the lirc sourceforge tree
and verified to work, been sitting there for months, finally getting
around to sending it. :\
Stefan reported a crash on a kernel before a3e5d1091c1 ("sched:
Don't call task_group() too many times in set_task_rq()"), he
found the reason to be that the multiple task_group()
invocations in set_task_rq() returned different values.
Looking at all that I found a lack of serialization and plain
wrong comments.
The below tries to fix it using an extra pointer which is
updated under the appropriate scheduler locks. Its not pretty,
but I can't really see another way given how all the cgroup
stuff works.
Reported-and-tested-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1340364965.18025.71.camel@twins Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d640113fe80e45ebd4a5b420b introduced a regression on SMP
systems where the processor core with ACPI id zero is disabled
(typically should be the case because of hyperthreading).
The regression got spread through stable kernels.
On 3.0.X it got introduced via 3.0.18.
Such platforms may be rare, but do exist.
Look out for a disabled processor with acpi_id 0 in dmesg:
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] disabled)
This problem has been observed on a:
HP Proliant BL280c G6 blade
This patch restricts the introduced workaround to platforms
with nr_cpu_ids <= 1.
Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch tries to fix a dead loop in async_synchronize_full(), which
could be seen when preemption is disabled on a single cpu machine.
void async_synchronize_full(void)
{
do {
async_synchronize_cookie(next_cookie);
} while (!list_empty(&async_running) || !
list_empty(&async_pending));
}
async_synchronize_cookie() calls async_synchronize_cookie_domain() with
&async_running as the default domain to synchronize.
However, there might be some works in the async_pending list from other
domains. On a single cpu system, without preemption, there is no chance
for the other works to finish, so async_synchronize_full() enters a dead
loop.
It seems async_synchronize_full() wants to synchronize all entries in
all running lists(domains), so maybe we could just check the entry_count
to know whether all works are finished.
Currently, async_synchronize_cookie_domain() expects a non-NULL running
list ( if NULL, there would be NULL pointer dereference ), so maybe a
NULL pointer could be used as an indication for the functions to
synchronize all works in all domains.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change eliminates an initialization-order hazard most
recently seen when netprio_cgroup is built into the kernel.
With thanks to Eric Dumazet for catching a bug.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Tested-by: Shea Levy <shea@shealevy.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Despite lots of investigation into why this is needed we don't
know or have an elegant cure. The only answer found on this
laptop is to mark a problem region as used so that Linux doesn't
put anything there.
Currently all the users add reserve= command lines and anyone
not knowing this needs to find the magic page that documents it.
Automate it instead.
Signed-off-by: Alan Cox <alan@linux.intel.com> Tested-and-bugfixed-by: Arne Fitzenreiter <arne@fitzenreiter.de>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=10231 Link: http://lkml.kernel.org/r/20120515174347.5109.94551.stgit@bluebook Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so the other CPU may temporarily see worker->flags which doesn't have
either WORKER_UNBOUND or WORKER_REBIND set and perform local wakeup
prematurely.
Fix it by using single explicit assignment via ACCESS_ONCE().
Because idle workers have another WORKER_NOT_RUNNING flag, this bug
doesn't exist for them; however, update it to use the same pattern for
consistency.
tj: Applied the change to idle workers too and updated comments and
patch description a bit.
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
There are some new video switch keys that used by newer machines.
0xA0 - SDSP HDMI only
0xA1 - SDSP LCD + HDMI
0xA2 - SDSP CRT + HDMI
0xA3 - SDSP TV + HDMI
But in Linux, there is no suitable userspace application to handle this,
so, mapping them all to KEY_SWITCHVIDEOMODE.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a more recent APU stepping with a new PCI ID
shipping in the same board by Fujitsu which needs the
same quirk to correctly mark the back plane connectors.
So we've had a fair few reports of fbcon handover breakage between
efi/vesafb and i915 surface recently, so I dedicated a couple of
days to finding the problem.
Essentially the last thing we saw was the conflicting framebuffer
message and that was all.
So after much tracing with direct netconsole writes (printks
under console_lock not so useful), I think I found the race.
Thread A (driver load) Thread B (timer thread)
unbind_con_driver -> |
bind_con_driver -> |
vc->vc_sw->con_deinit -> |
fbcon_deinit -> |
console_lock() |
| |
| fbcon_flashcursor timer fires
| console_lock() <- blocked for A
|
|
fbcon_del_cursor_timer ->
del_timer_sync
(BOOM)
Of course because all of this is under the console lock,
we never see anything, also since we also just unbound the active
console guess what we never see anything.
Hopefully this fixes the problem for anyone seeing vesafb->kms
driver handoff.
v1.1: add comment suggestion from Alan.
Signed-off-by: Dave Airlie <airlied@redhat.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Tested-by: Josh Boyer <jwboyer@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many of our larger systems, CPU 0 has had all of its IRQ resources
consumed before XPC loads. Worst cases on machines with multiple 10
GigE cards and multiple IB cards have depleted the entire first socket
of IRQs.
This patch makes selecting the node upon which IRQs are allocated (as
well as all the other GRU Message Queue structures) specifiable as a
module load param and has a default behavior of searching all nodes/cpus
for an available resources.
[akpm@linux-foundation.org: fix build: include cpu.h and module.h] Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The power.deferred_resume can only be set if the runtime PM status
of device is RPM_SUSPENDING and it should be cleared after its
status has been changed, regardless of whether or not the runtime
suspend has been successful. However, it only is cleared on
suspend failure, while it may remain set on successful suspend and
is happily leaked to rpm_resume() executed in that case.
That shouldn't happen, so if power.deferred_resume is set in
rpm_suspend() after the status has been changed to RPM_SUSPENDED,
clear it before calling rpm_resume(). Then, it doesn't need to be
cleared before changing the status to RPM_SUSPENDING any more,
because it's always cleared after the status has been changed to
either RPM_SUSPENDED (on success) or RPM_ACTIVE (on failure).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devices whose power.no_callbacks flag is set, rpm_resume()
should return 1 if the device's parent is already active, so that
the callers of pm_runtime_get() don't think that they have to wait
for the device to resume (asynchronously) in that case (the core
won't queue up an asynchronous resume in that case, so there's
nothing to wait for anyway).
Modify the code accordingly (and make sure that an idle notification
will be queued up on success, even if 1 is to be returned).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the offset by subtracting 20 from tm_hour before taking the
modulo 12.
[ "Why 20?" I hear you ask. Or at least I did.
Here's the reason why: RS5C348_BIT_PM is 32, and is - stupidly -
included in the RS5C348_HOURS_MASK define. So it's really subtracting
out that bit to get "hour+12". But then because it does things modulo
12, it needs to add the 12 in again afterwards anyway.
This code is confused. It would be much clearer if RS5C348_HOURS_MASK
just didn't include the RS5C348_BIT_PM bit at all, then it wouldn't
need to do the silly subtract either.
Whatever. It's all just math, the end result is the same. - Linus ]
Reported-by: James Nute <newten82@gmail.com> Tested-by: James Nute <newten82@gmail.com> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARM recently moved to asm-generic/mutex-xchg.h for its mutex
implementation after the previous implementation was found to be missing
some crucial memory barriers. However, this has revealed some problems
running hackbench on SMP platforms due to the way in which the
MUTEX_SPIN_ON_OWNER code operates.
The symptoms are that a bunch of hackbench tasks are left waiting on an
unlocked mutex and therefore never get woken up to claim it. This boils
down to the following sequence of events:
At this point, the lock is unlocked, but Task B is in an uninterruptible
sleep with nobody to wake it up.
This patch fixes the problem by ensuring we put the lock into the
contended state if we fail to acquire it on the fastpath, ensuring that
any blocked waiters are woken up when the mutex is released.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Chris Mason <chris.mason@fusionio.com> Cc: Ingo Molnar <mingo@elte.hu> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/n/tip-6e9lrw2avczr0617fzl5vqb8@git.kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches. The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.
The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB. The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added. It assumed that the dequeue pointer could never
point to a link TRB. It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.
This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land. It would then read from
that memory to determine if it was a link TRB. Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.
Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of. inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.
The only reason the original code worked at all is because there was
only one ring segment. With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync. On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:
ERROR Transfer event TRB DMA ptr not part of current TD
This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),
https://bugzilla.kernel.org/show_bug.cgi?id=43333
and possibly other general protection fault bugs as well.
This patch should be backported to kernels as old as 2.6.31. A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: James Ettle <theholyettlz@googlemail.com> Tested-by: Matthew Hall <mhall@mhcomputing.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com> Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: adam ? <adam3337@wp.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b69cc672052540 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Apparently, am-utils is still using the legacy binary mountdata interface,
and is having trouble parsing /proc/mounts due to the 'port=' field being
incorrectly set.
When the NFS_COOKIEVERF helper macro was converted into a static
inline function in commit 99fadcd764 (nfs: convert NFS_*(inode)
helpers to static inline), we broke the initialisation of the
readdir cookies, since that depended on doing a memset with an
argument of 'sizeof(NFS_COOKIEVERF(inode))' which therefore
changed from sizeof(be32 cookieverf[2]) to sizeof(be32 *).
At this point, NFS_COOKIEVERF seems to be more of an obfuscation
than a helper, so the best thing would be to just get rid of it.
Also see: https://bugzilla.kernel.org/show_bug.cgi?id=46881
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.
When call_crda() is called we kick off a witch hunt search
for the same regulatory domain on our internal regulatory
database and that work gets kicked off on a workqueue, this
is done while the cfg80211_mutex is held. If that workqueue
kicks off it will first lock reg_regdb_search_mutex and
later cfg80211_mutex but to ensure two CPUs will not contend
against cfg80211_mutex the right thing to do is to have the
reg_regdb_search() wait until the cfg80211_mutex is let go.
The lockdep report is pasted below.
cfg80211: Calling CRDA to update world regulatory domain
======================================================
[ INFO: possible circular locking dependency detected ]
3.3.8 #3 Tainted: G O
-------------------------------------------------------
kworker/0:1/235 is trying to acquire lock:
(cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
but task is already holding lock:
(reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Reported-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:
Signed-off-by: Søren Holm <sgh@sgh.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch zeroes the SCTLR.TRE bit prior to setting the mapping as
cacheable for ARMv7 cores in the decompressor, ensuring that the
memory region attributes are obtained from the C and B bits, not from
the page tables.
Cc: Nicolas Pitre <nico@fluxnic.net> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Matthew Leach <matthew.leach@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARM: fix bad applied patch for arch/arm/Kconfig of stable 3.0.y tree.
No upstream commit as this is a merge error in the 3.0 tree.
ARM_ERRATA_764369 and PL310_ERRATA_769419 do not appear in config menu in
stable 3.0.y tree.
This is because backported patch for arm/arm/Kconfig applied wrong place.
This patch solves it.
kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.
Signed-off-by: Toshi Kani <toshi.kani@hp.com> Tested-by: Lisa Mitchell <lisa.mitchell@hp.com> Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk introduced with commit 00250ec90963b7ef6678438888f3244985ecde14 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hypervisor is in charge of allocating the proper "NUMA" memory
and dealing with the CPU scheduler to keep them bound to the proper
NUMA node. The PV guests (and PVHVM) have no inkling of where they
run and do not need to know that right now. In the future we will
need to inject NUMA configuration data (if a guest spans two or more
NUMA nodes) so that the kernel can make the right choices. But those
patches are not yet present.
In the meantime, disable the NUMA capability in the PV guest, which
also fixes a bootup issue. Andre says:
"we see Dom0 crashes due to the kernel detecting the NUMA topology not
by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA).
This will detect the actual NUMA config of the physical machine, but
will crash about the mismatch with Dom0's virtual memory. Variation of
the theme: Dom0 sees what it's not supposed to see.
This happens with the said config option enabled and on a machine where
this scanning is still enabled (K8 and Fam10h, not Bulldozer class)
There may be a bug when registering section info. For example, on my
Itanium platform, the pfn range of node0 includes the other nodes, so
other nodes' section info will be double registered, and memmap's page
count will equal to 3.
Because MIN_MEMORY_BLOCK_SIZE is int type and length of 32bits,
so MIN_MEMORY_BLOCK_SIZE(1 << 32) will will equal to 0.
Actually when SECTION_SIZE_BITS >= 31, MIN_MEMORY_BLOCK_SIZE will be wrong.
This will cause wrong system memory infomation in sysfs.
I think it should be:
And "echo offline > memory0/state" will cause following call trace:
kernel BUG at mm/memory_hotplug.c:885!
sh[6455]: bugcheck! 0 [1]
Pid: 6455, CPU 0, comm: sh
psr : 0000101008526030 ifs : 8000000000000fa4 ip : [<a0000001008c40f0>] Not tainted (3.6.0-rc1)
ip is at offline_pages+0x210/0xee0
Call Trace:
show_stack+0x80/0xa0
show_regs+0x640/0x920
die+0x190/0x2c0
die_if_kernel+0x50/0x80
ia64_bad_break+0x3d0/0x6e0
ia64_native_leave_kernel+0x0/0x270
offline_pages+0x210/0xee0
alloc_pages_current+0x180/0x2a0
Signed-off-by: Jianguo Wu <wujianguo@huawei.com> Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: "Luck, Tony" <tony.luck@intel.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com> Cc: Felipe Balbi <balbi@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The heuristic method for buddy has been introduced since commit 43506fad21ca ("mm/page_alloc.c: simplify calculation of combined index
of adjacent buddy lists"). But the page address of higher page's buddy
was wrongly calculated, which will lead page_is_buddy to fail for ever.
IOW, the heuristic method would be disabled with the wrong page address
of higher page's buddy.
Calculating the page address of higher page's buddy should be based
higher_page with the offset between index of higher page and index of
higher page's buddy.
Signed-off-by: Haifeng Li <omycle@gmail.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: KyongHo Cho <pullip.cho@samsung.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Johannes Weiner <jweiner@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following build error occurred during an alpha build:
net/core/sock.c:274:36: error: initializer element is not constant
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
> goto out;
>
> /* copy keys to file */
> - for (i = 0; i < env->envp_idx; i++)
> + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> + for (i = 0; i < env->envp_idx; i++) {
> + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
> count += sprintf(&buf[count], "%s\n", env->envp[i]);
> + }
>
> Oops message, the env[] is again not properly initilized:
>
> [ 44.068623] input input0: uevent 61 env[805306368]: input0/.../input0
> [ 44.069552] uevent 0 env[0]: (null)
This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away. I had a
hard time trying to disable it anyway ;-)
The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0. This is not true
if CONFIG_HOTPLUG is unset. So things like this end up overwriting
env->envp_idx because the array index is -1:
if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
len = input_print_modalias(&env->buf[env->buflen - 1],
sizeof(env->buf) - env->buflen,
dev, 0);
Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel. This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.
[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Don't mess with file refcounts (or keep a reference to file, for
that matter) in perf_event. Use explicit refcount of its own
instead. Deal with the race between the final reference to event
going away and new children getting created for it by use of
atomic_long_inc_not_zero() in inherit_event(); just have the
latter free what it had allocated and return NULL, that works
out just fine (children of siblings of something doomed are
created as singletons, same as if the child of leader had been
created and immediately killed).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20120820135925.GG23464@ZenIV.linux.org.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Dave Jones <davej@redhat.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
This patch fixes a long-standing bug with SCSI overflow handling
where se_cmd->data_length was incorrectly being re-assigned to
the larger CDB extracted allocation length, resulting in a number
of fabric level errors that would end up causing a session reset
in most cases. So instead now:
- Only re-assign se_cmd->data_length durining UNDERFLOW (to use the
smaller value)
- Use existing se_cmd->data_length for OVERFLOW (to use the smaller
value)
This fix has been tested with the following CDB to generate an
SCSI overflow:
sg_raw -r512 /dev/sdc 28 0 0 0 0 0 0 0 9 0
Tested using iscsi-target, tcm_qla2xxx, loopback and tcm_vhost fabric
ports. Here is a bit more detail on each case:
- iscsi-target: Bug with open-iscsi with overflow, sg_raw returns
-3584 bytes of data.
- tcm_qla2xxx: Working as expected, returnins 512 bytes of data
- loopback: sg_raw returns CHECK_CONDITION, from overflow rejection
in transport_generic_map_mem_to_cmd()
- tcm_vhost: Same as loopback
Reported-by: Roland Dreier <roland@purestorage.com> Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.
This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.
http://launchpad.net/bugs/561129
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Tested-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log