When trying to set the ICST 307 clock to 25174000 Hz I ran into
this arithmetic error: the icst_hz_to_vco() correctly figure out
DIVIDE=2, RDW=100 and VDW=99 yielding a frequency of 25174000 Hz out of the VCO. (I replicated the icst_hz() function
in a spreadsheet to verify this.)
However, when I called icst_hz() on these VCO settings it would
instead return 4122709 Hz. This causes an error in the common
clock driver for ICST as the common clock framework will call
.round_rate() on the clock which will utilize icst_hz_to_vco()
followed by icst_hz() suggesting the erroneous frequency, and
then the clock gets set to this.
The error did not manifest in the old clock framework since
this high frequency was only used by the CLCD, which calls
clk_set_rate() without first calling clk_round_rate() and since
the old clock framework would not call clk_round_rate() before
setting the frequency, the correct values propagated into
the VCO.
After some experimenting I figured out that it was due to a simple
arithmetic overflow: the divisor for 24Mhz reference frequency
as reference becomes 24000000*2*(99+8)=0x132212400 and the "1"
in bit 32 overflows and is lost.
But introducing an explicit 64-by-32 bit do_div() and casting
the divisor into (u64) we get the right frequency back, and the
right frequency gets set.
Tested on the ARM Versatile.
Cc: linux-clk@vger.kernel.org Cc: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the dawn of time the ICST code has only supported divide
by one or hang in an eternal loop. Luckily we were always dividing
by one because the reference frequency for the systems using
the ICSTs is 24MHz and the [min,max] values for the PLL input
if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop
will always terminate immediately without assigning any divisor
for the reference frequency.
But for the code to make sense, let's insert the missing i++
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a name contains at least some characters with Unicode values
exceeding single byte, the CS0 output should have 2 bytes per character.
And if other input characters have single byte Unicode values, then
the single input byte is converted to 2 output bytes, and the length
of output becomes larger than the length of input. And if the input
name is long enough, the output length may exceed the allocated buffer
length.
All this means that conversion from UTF8 or NLS to CS0 requires
checking of output length in order to stop when it exceeds the given
output buffer size.
[JK: Make code return -ENAMETOOLONG instead of silently truncating the
name]
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udf_CS0toUTF8 function stops the conversion when the output buffer
length reaches UDF_NAME_LEN-2, which is correct maximum name length,
but, when checking, it leaves the space for a single byte only,
while multi-bytes output characters can take more space, causing
buffer overflow.
Similar error exists in udf_CS0toNLS function, that restricts
the output length to UDF_NAME_LEN, while actual maximum allowed
length is UDF_NAME_LEN-2.
In these cases the output can override not only the current buffer
length field, causing corruption of the name buffer itself, but also
following allocation structures, causing kernel crash.
Adjust the output length checks in both functions to prevent buffer
overruns in case of multi-bytes UTF8 or NLS characters.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udf_next_aext() just follows extent pointers while extents are marked as
indirect. This can loop forever for corrupted filesystem. Limit number
the of indirect extents we are willing to follow in a row.
[JK: Updated changelog, limit, style]
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Jan Kara <jack@suse.com> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've seen this in a packet capture - I've intermixed what I
think was going on. The fix here is to grab the so_lock sooner.
1964379 -> #1 open (for write) reply seqid=1 1964393 -> #2 open (for read) reply seqid=2
__nfs4_close(), state->n_wronly--
nfs4_state_set_mode_locked(), changes state->state = [R]
state->flags is [RW]
state->state is [R], state->n_wronly == 0, state->n_rdonly == 1
1964398 -> #3 open (for write) call -> because close is already running 1964399 -> downgrade (to read) call seqid=2 (close of #1) 1964402 -> #3 open (for write) reply seqid=3
__update_open_stateid()
nfs_set_open_stateid_locked(), changes state->flags
state->flags is [RW]
state->state is [R], state->n_wronly == 0, state->n_rdonly == 1
new sequence number is exposed now via nfs4_stateid_copy()
next step would be update_open_stateflags(), pending so_lock
1964403 -> downgrade reply seqid=2, fails with OLD_STATEID (close of #1)
nfs4_close_prepare() gets so_lock and recalcs flags -> send close
The setup_ntlmv2_rsp() function may return positive value ENOMEM instead
of -ENOMEM in case of kmalloc failure.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPI tx and rx buffers are both supposed to be scan_bytes amount of
bytes large and a common allocation is used to allocate both buffers. This
puts the beginning of the tx buffer scan_bytes bytes after the rx buffer.
The initialization of the tx buffer pointer is done adding scan_bytes to
the beginning of the rx buffer, but since the rx buffer is of type __be16
this will actually add two times as much and the tx buffer ends up pointing
after the allocated buffer.
Fix this by using scan_count, which is scan_bytes / 2, instead of
scan_bytes when initializing the tx buffer pointer.
Fixes: aacff892cbd5 ("staging:iio:adis: Preallocate transfer message") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_master_send() returns the number of bytes transferred on success while
the ad5064 driver expects that the write() callback returns 0 on success.
Fix that by translating any non negative return value of i2c_master_send()
to 0.
Fixes: commit 6a17a0768f77 ("iio:dac:ad5064: Add support for the ad5629r and ad5669r") Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What appears to be happening is that something has pinned the target
so it can't go into STARGET_DEL via final release and the loop in
scsi_remove_target spins endlessly until that happens.
The fix for this soft lockup is to not keep looping over a device that
we've called remove on but which hasn't gone into DEL state. This
patch will retain a simplistic memory of the last target and not keep
looping over it.
Reported-by: Sebastian Herbszt <herbszt@gmx.de> Tested-by: Sebastian Herbszt <herbszt@gmx.de> Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38 Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If MODE SELECT returns with sense '05/91/36' (command lock violation)
it should always be retried without counting the number of retries.
During an HBA upgrade or similar circumstances one might see a flood
of MODE SELECT command from various HBAs, which will easily trigger
the sense code and exceed the retry count.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Runtime suspend during driver probe and removal can cause problems.
The driver's runtime_suspend or runtime_resume callbacks may invoked
before the driver has finished binding to the device or after the
driver has unbound from the device.
This problem shows up with the sd and sr drivers, and can cause disk
or CD/DVD drives to become unusable as a result. The fix is simple.
The drivers store a pointer to the scsi_disk or scsi_cd structure as
their private device data when probing is finished, so we simply have
to be sure to clear the private data during removal and test it during
runtime suspend/resume.
This fixes <https://bugs.debian.org/801925>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Paul Menzel <paul.menzel@giantmonkey.de> Reported-by: Erich Schubert <erich@debian.org> Reported-by: Alexandre Rossi <alexandre.rossi@gmail.com> Tested-by: Paul Menzel <paul.menzel@giantmonkey.de> Tested-by: Erich Schubert <erich@debian.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a iscsi-target specific bug-fix for a dead-lock
that can occur during explicit struct se_node_acl->acl_group
se_session deletion via configfs rmdir(2), when iscsi-target
time2retain timer is still active.
It changes iscsi-target to obtain se_portal_group->session_lock
internally using spin_in_locked() to check for the specific
se_node_acl configfs shutdown rmdir(2) case.
Note this patch is intended for stable, and the subsequent
v4.5-rc patch converts target_core_tpg.c to use proper
se_sess->sess_kref reference counting for both se_node_acl
deletion + se_node_acl->queue_depth se_session restart.
Reported-by:: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routines in scsi_pm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by checking q->dev in block layer before
handle runtime PM. Since ses doesn't define any PM callbacks and call
blk_pm_runtime_init(), the crash won't occur.
This fixes Bugzilla #101371.
https://bugzilla.kernel.org/show_bug.cgi?id=101371
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: Xiangliang Yu <Xiangliang.Yu@amd.com> Cc: James E.J. Bottomley <JBottomley@odin.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Terry <Michael.terry@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid that kmemleak reports the following memory leak if a
SCSI LLD calls scsi_host_alloc() and scsi_host_put() but neither
scsi_host_add() nor scsi_host_remove(). The following shell
command triggers that scenario:
for ((i=0; i<2; i++)); do
srp_daemon -oac |
while read line; do
echo $line >/sys/class/infiniband_srp/srp-mlx4_0-1/add_target
done
done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.
The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.
To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).
Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dropping a lock while iterating a list we must restart the search
as other threads could have manipulated the list under us. Without this
we can get stuck in an endless loop. This bug was introduced by
The starting node for a klist iteration is often passed in from
somewhere way above the klist infrastructure, meaning there's no
guarantee the node is still on the list. We've seen this in SCSI where
we use bus_find_device() to iterate through a list of devices. In the
face of heavy hotplug activity, the last device returned by
bus_find_device() can be removed before the next call. This leads to
Dec 3 13:22:02 localhost kernel: WARNING: CPU: 2 PID: 28073 at include/linux/kref.h:47 klist_iter_init_node+0x3d/0x50()
Dec 3 13:22:02 localhost kernel: Modules linked in: scsi_debug x86_pkg_temp_thermal kvm_intel kvm irqbypass crc32c_intel joydev iTCO_wdt dcdbas ipmi_devintf acpi_power_meter iTCO_vendor_support ipmi_si imsghandler pcspkr wmi acpi_cpufreq tpm_tis tpm shpchp lpc_ich mfd_core nfsd nfs_acl lockd grace sunrpc tg3 ptp pps_core
Dec 3 13:22:02 localhost kernel: CPU: 2 PID: 28073 Comm: cat Not tainted 4.4.0-rc1+ #2
Dec 3 13:22:02 localhost kernel: Hardware name: Dell Inc. PowerEdge R320/08VT7V, BIOS 2.0.22 11/19/2013
Dec 3 13:22:02 localhost kernel: ffffffff81a20e77ffff880613acfd18ffffffff81321eef0000000000000000
Dec 3 13:22:02 localhost kernel: ffff880613acfd50ffffffff8107ca52ffff88061176b1980000000000000000
Dec 3 13:22:02 localhost kernel: ffffffff814542b0ffff880610cfb100ffff88061176b198ffff880613acfd60
Dec 3 13:22:02 localhost kernel: Call Trace:
Dec 3 13:22:02 localhost kernel: [<ffffffff81321eef>] dump_stack+0x44/0x55
Dec 3 13:22:02 localhost kernel: [<ffffffff8107ca52>] warn_slowpath_common+0x82/0xc0
Dec 3 13:22:02 localhost kernel: [<ffffffff814542b0>] ? proc_scsi_show+0x20/0x20
Dec 3 13:22:02 localhost kernel: [<ffffffff8107cb4a>] warn_slowpath_null+0x1a/0x20
Dec 3 13:22:02 localhost kernel: [<ffffffff8167225d>] klist_iter_init_node+0x3d/0x50
Dec 3 13:22:02 localhost kernel: [<ffffffff81421d41>] bus_find_device+0x51/0xb0
Dec 3 13:22:02 localhost kernel: [<ffffffff814545ad>] scsi_seq_next+0x2d/0x40
[...]
And an eventual crash. It can actually occur in any hotplug system
which has a device finder and a starting device.
We can fix this globally by making sure the starting node for
klist_iter_init_node() is actually a member of the list before using it
(and by starting from the beginning if it isn't).
Reported-by: Ewan D. Milne <emilne@redhat.com> Tested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my randconfig tests, I came across a bug that involves several
components:
* gcc-4.9 through at least 5.3
* CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files
* CONFIG_PROFILE_ALL_BRANCHES overriding every if()
* The optimized implementation of do_div() that tries to
replace a library call with an division by multiplication
* code in drivers/media/dvb-frontends/zl10353.c doing
In this case, gcc fails to determine whether the divisor
in do_div() is __builtin_constant_p(). In particular, it
concludes that __builtin_constant_p(adc_clock) is false, while
__builtin_constant_p(!!adc_clock) is true.
That in turn throws off the logic in do_div() that also uses
__builtin_constant_p(), and instead of picking either the
constant- optimized division, and the code in ilog2() that uses
__builtin_constant_p() to figure out whether it knows the answer at
compile time. The result is a link error from failing to find
multiple symbols that should never have been called based on
the __builtin_constant_p():
dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN'
dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod'
ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined!
ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined!
This patch avoids the problem by changing __trace_if() to check
whether the condition is known at compile-time to be nonzero, rather
than checking whether it is actually a constant.
I see this one link error in roughly one out of 1600 randconfig builds
on ARM, and the patch fixes all known instances.
Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.de Acked-by: Nicolas Pitre <nico@linaro.org> Fixes: ab3c9c686e22 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By checking the effective credentials instead of the real UID / permitted
capabilities, ensure that the calling process actually intended to use its
credentials.
To ensure that all ptrace checks use the correct caller credentials (e.g.
in case out-of-tree code or newly added code omits the PTRACE_MODE_*CREDS
flag), use two new flags and require one of them to be set.
The problem was that when a privileged task had temporarily dropped its
privileges, e.g. by calling setreuid(0, user_uid), with the intent to
perform following syscalls with the credentials of a user, it still passed
ptrace access checks that the user would not be able to pass.
While an attacker should not be able to convince the privileged task to
perform a ptrace() syscall, this is a problem because the ptrace access
check is reused for things in procfs.
In particular, the following somewhat interesting procfs entries only rely
on ptrace access checks:
/proc/$pid/stat - uses the check for determining whether pointers
should be visible, useful for bypassing ASLR
/proc/$pid/maps - also useful for bypassing ASLR
/proc/$pid/cwd - useful for gaining access to restricted
directories that contain files with lax permissions, e.g. in
this scenario:
lrwxrwxrwx root root /proc/13020/cwd -> /root/foobar
drwx------ root root /root
drwxr-xr-x root root /root/foobar
-rw-r--r-- root root /root/foobar/secret
Therefore, on a system where a root-owned mode 6755 binary changes its
effective credentials as described and then dumps a user-specified file,
this could be used by an attacker to reveal the memory layout of root's
processes or reveal the contents of files he is not allowed to access
(through /proc/$pid/cwd).
[akpm@linux-foundation.org: fix warning] Signed-off-by: Jann Horn <jann@thejh.net> Acked-by: Kees Cook <keescook@chromium.org> Cc: Casey Schaufler <casey@schaufler-ca.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Morris <james.l.morris@oracle.com> Cc: "Serge E. Hallyn" <serge.hallyn@ubuntu.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnaldo reported that tracepoint filters seem to misbehave (ie. not
apply) on inherited events.
The fix is obvious; filters are only set on the actual (parent)
event, use the normal pattern of using this parent event for filters.
This is safe because each child event has a reference to it.
This happens because in the code path executed by the inode_paths ioctl we
end up nesting two calls to read lock a leaf's rwlock when after the first
call to read_lock() and before the second call to read_lock(), another
task (running the delayed items as part of a transaction commit) has
already called write_lock() against the leaf's rwlock. This situation is
illustrated by the following diagram:
read_lock(&eb->lock);
--> makes this task hang
forever (and task B too
of course)
So fix this by avoiding doing the nested read lock, which is easily
avoidable. This issue does not happen if task B calls write_lock() after
task A does the second call to read_lock(), however there does not seem
to exist anything in the documentation that mentions what is the expected
behaviour for recursive locking of rwlocks (leaving the idea that doing
so is not a good usage of rwlocks).
Also, as a side effect necessary for this fix, make sure we do not
needlessly read lock extent buffers when the input path has skip_locking
set (used when called from send).
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sizeof(ext_new_group_data) > sizeof(ext_new_flex_group_data),
integer overflow could be happened.
Therefore, need to fix integer overflow sanitization.
In Linus's tree, the iovec code has been reworked massively, but in
older kernels the AIO layer should be checking this before passing the
request on to other layers.
Many thanks to Ben Hawkes of Google Project Zero for pointing out the
issue.
Reported-by: Ben Hawkes <hawkes@google.com> Acked-by: Benjamin LaHaise <bcrl@kvack.org> Tested-by: Willy Tarreau <w@1wt.eu>
[backported to 3.10 - willy] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering current pty code and multiple devpts instances, it's possible
to umount a devpts file system while a program still has /dev/tty opened
pointing to a previosuly closed pty pair in that instance. In the case all
ptmx and pts/N files are closed, umount can be done. If the program closes
/dev/tty after umount is done, devpts_kill_index will use now an invalid
super_block, which was already destroyed in the umount operation after
running ->kill_sb. This is another "use after free" type of issue, but now
related to the allocated super_block instance.
To avoid the problem (warning at ida_remove and potential crashes) for
this specific case, I added two functions in devpts which grabs additional
references to the super_block, which pty code now uses so it makes sure
the super block structure is still valid until pty shutdown is done.
I also moved the additional inode references to the same functions, which
also covered similar case with inode being freed before /dev/tty final
close/shutdown.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a bug for a corner case where we have the the last
release from a pty master/slave coming from a previously opened /dev/tty
file. When this happens, the tty->driver_data can be stale, due to all
ptmx or pts/N files having already been closed before (and thus the inode
related to these files, which tty->driver_data points to, being already
freed/destroyed).
The fix here is to keep a reference on the opened master ptmx inode.
We maintain the inode referenced until the final pty_unix98_shutdown,
and only pass this inode to devpts_kill_index.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the function documentation for tty_ldisc_ref_wait() notes, it is
only callable from a tty file_operations routine; otherwise there
is no guarantee the ref won't be NULL.
The key difference with the VT's paste_selection() is that is an ioctl,
where __speakup_paste_selection() is completely async kworker, kicked
off from interrupt context.
Fixes: 28a821c30688 ("Staging: speakup: Update __speakup_paste_selection()
tty (ab)usage to match vt") Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [7f0973e973cd: ALSA: seq: Fix lockdep warnings due to
double mutex locks] split the management of two linked lists (source
and destination) into two individual calls for avoiding the AB/BA
deadlock. However, this may leave the possible double deletion of one
of two lists when the counterpart is being deleted concurrently.
It ends up with a list corruption, as revealed by syzkaller fuzzer.
This patch fixes it by checking the list emptiness and skipping the
deletion and the following process.
Do not clobber the buffer space passed from `search_binary_handler' and
originally preloaded by `prepare_binprm' with the executable's file
header by overwriting it with its interpreter's file header. Instead
keep the buffer space intact and directly use the data structure locally
allocated for the interpreter's file header, fixing a bug introduced in
2.1.14 with loadable module support (linux-mips.org commit beb11695
[Import of Linux/MIPS 2.1.14], predating kernel.org repo's history).
Adjust the amount of data read from the interpreter's file accordingly.
This was not an issue before loadable module support, because back then
`load_elf_binary' was executed only once for a given ELF executable,
whether the function succeeded or failed.
With loadable module support supported and enabled, upon a failure of
`load_elf_binary' -- which may for example be caused by architecture
code rejecting an executable due to a missing hardware feature requested
in the file header -- a module load is attempted and then the function
reexecuted by `search_binary_handler'. With the executable's file
header replaced with its interpreter's file header the executable can
then be erroneously accepted in this subsequent attempt.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We miss to take the crypto_alg_sem semaphore when traversing the
crypto_alg_list for CRYPTO_MSG_GETALG dumps. This allows a race with
crypto_unregister_alg() removing algorithms from the list while we're
still traversing it, thereby leading to a use-after-free as show below:
To trigger the race run the following loops simultaneously for a while:
$ while : ; do modprobe aesni-intel; rmmod aesni-intel; done
$ while : ; do crconf show all > /dev/null; done
Fix the race by taking the crypto_alg_sem read lock, thereby preventing
crypto_unregister_alg() from modifying the algorithm list during the
dump.
This bug has been detected by the PaX memory sanitize feature.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: PaX Team <pageexec@freemail.hu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some early controllers incorrectly reported zero ports in PORTS_IMPL
register and the ahci driver fabricates PORTS_IMPL from the number of
ports in those cases. This hasn't mattered but with the new nvme
controllers there are cases where zero PORTS_IMPL is valid and should
be honored.
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
Each af_alg parent socket obtained by socket(2) corresponds to a
tfm object once bind(2) has succeeded. An accept(2) call on that
parent socket creates a context which then uses the tfm object.
Therefore as long as any child sockets created by accept(2) exist
the parent socket must not be modified or freed.
This patch guarantees this by using locks and a reference count
on the parent socket. Any attempt to modify the parent socket will
fail with EBUSY.
In ext4, the bottom two bits of {a,c,m}time_extra are used to extend
the {a,c,m}time fields, deferring the year 2038 problem to the year
2446.
When decoding these extended fields, for times whose bottom 32 bits
would represent a negative number, sign extension causes the 64-bit
extended timestamp to be negative as well, which is not what's
intended. This patch corrects that issue, so that the only negative
{a,c,m}times are those between 1901 and 1970 (as per 32-bit signed
timestamps).
Some older kernels might have written pre-1970 dates with 1,1 in the
extra bits. This patch treats those incorrectly-encoded dates as
pre-1970, instead of post-2311, until kernel 4.20 is released.
Hopefully by then e2fsck will have fixed up the bad data.
Also add a comment explaining the encoding of ext4's extra {a,c,m}time
bits.
Signed-off-by: David Turner <novalis@novalis.org> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reported-by: Mark Harris <mh8928@yahoo.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=23732 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl(TIOCGETD) retrieves the line discipline id directly from the
ldisc because the line discipline id (c_line) in termios is untrustworthy;
userspace may have set termios via ioctl(TCSETS*) without actually
changing the line discipline via ioctl(TIOCSETD).
However, directly accessing the current ldisc via tty->ldisc is
unsafe; the ldisc ptr dereferenced may be stale if the line discipline
is changing via ioctl(TIOCSETD) or hangup.
Wait for the line discipline reference (just like read() or write())
to retrieve the "current" line discipline id.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In certain kernel configurations where the cdc_ether and option drivers
are compiled as modules there can occur a race condition in enumeration.
This causes the option driver to enumerate the ethernet(wwan) interface
as usb-serial interfaces.
Signed-off-by: John Ernberg <john.ernberg@actia.se> Fixes: 1941138e1c02 ("USB: added support for Cinterion's products...") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
Ben Hutchings [Wed, 23 Dec 2015 13:25:54 +0000 (13:25 +0000)]
USB: ti_usb_3410_502: Fix ID table size
Commit 35a2fbc941ac ("USB: serial: ti_usb_3410_5052: new device id for
Abbot strip port cable") failed to update the size of the
ti_id_table_3410 array. This doesn't need to be fixed upstream
following commit d7ece6515e12 ("USB: ti_usb_3410_5052: remove
vendor/product module parameters") but should be fixed in stable
branches older than 3.12.
Backports of commit c9d09dc7ad10 ("USB: serial: ti_usb_3410_5052: add
Abbott strip port ID to combined table as well.") similarly failed to
update the size of the ti_id_table_combined array.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A slave timer element also unlinks at snd_timer_stop() but it takes
only slave_active_lock. When a slave is assigned to a master,
however, this may become a race against the master's interrupt
handling, eventually resulting in a list corruption. The actual bug
could be seen with a syzkaller fuzzer test case in BugLink below.
As a fix, we need to take timeri->timer->lock when timer isn't NULL,
i.e. assigned to a master, while the assignment to a master itself is
protected by slave_active_lock.
Currently the selected timer backend is referred at any moment from
the running PCM callbacks. When the backend is switched, it's
possible to lead to inconsistency from the running backend. This was
pointed by syzkaller fuzzer, and the commit [7ee96216c31a: ALSA:
dummy: Disable switching timer backend via sysfs] disabled the dynamic
switching for avoiding the crash.
This patch improves the handling of timer backend switching. It keeps
the reference to the selected backend during the whole operation of an
opened stream so that it won't be changed by other streams.
Together with this change, the hrtimer parameter is reenabled as
writable now.
NOTE: this patch also turned out to fix the still remaining race.
Namely, ops was still replaced dynamically at dummy_pcm_open:
static int dummy_pcm_open(struct snd_pcm_substream *substream)
{
....
dummy->timer_ops = &dummy_systimer_ops;
if (hrtimer)
dummy->timer_ops = &dummy_hrtimer_ops;
Since dummy->timer_ops is common among all streams, and when the
replacement happens during accesses of other streams, it may lead to a
crash. This was actually triggered by syzkaller fuzzer and KASAN.
This patch rewrites the code not to use the ops shared by all streams
any longer, too.
In snd_timer_notify1(), the wrong timer instance was passed for slave
ccallback function. This leads to the access to the wrong data when
an incompatible master is handled (e.g. the master is the sequencer
timer and the slave is a user timer), as spotted by syzkaller fuzzer.
Although ALSA timer code got hardening for races, it still causes
use-after-free error. This is however rather a corrupted linked list,
not actually the concurrent accesses. Namely, when timer start is
triggered twice, list_add_tail() is called twice, too. This ends
up with the link corruption and triggers KASAN error.
The simplest fix would be replacing list_add_tail() with
list_move_tail(), but fundamentally it's the problem that we don't
check the double start/stop correctly. So, the right fix here is to
add the proper checks to snd_timer_start() and snd_timer_stop() (and
their variants).
In ALSA timer core, the active timer instance is managed in
active_list linked list. Each element is added / removed dynamically
at timer start, stop and in timer interrupt. The problem is that
snd_timer_interrupt() has a thinko and leaves the element in
active_list when it's the last opened element. This eventually leads
to list corruption or use-after-free error.
This hasn't been revealed because we used to delete the list forcibly
in snd_timer_stop() in the past. However, the recent fix avoids the
double-stop behavior (in commit [f784beb75ce8: ALSA: timer: Fix link
corruption due to double start or stop]), and this leak hits reality.
This patch fixes the link management in snd_timer_interrupt(). Now it
simply unlinks no matter which stream is.
This is a minor code cleanup without any functional changes:
- Kill keep_flag argument from _snd_timer_stop(), as all callers pass
only it false.
- Remove redundant NULL check in _snd_timer_stop().
The port subscription code uses double mutex locks for source and
destination ports, and this may become racy once when wrongly set up.
It leads to lockdep warning splat, typically triggered by fuzzer like
syzkaller, although the actual deadlock hasn't been seen, so far.
This patch simplifies the handling by reducing to two single locks, so
that no lockdep warning will be trigger any longer.
By splitting to two actions, a still-in-progress element shall be
added in one list while handling another. For ignoring this element,
a new check is added in deliver_to_subscribers().
Along with it, the code to add/remove the subscribers list element was
cleaned up and refactored.
ALSA sequencer may open/close and control ALSA timer instance
dynamically either via sequencer events or direct ioctls. These are
done mostly asynchronously, and it may call still some timer action
like snd_timer_start() while another is calling snd_timer_close().
Since the instance gets removed by snd_timer_close(), it may lead to
a use-after-free.
This patch tries to address such a race by protecting each
snd_timer_*() call via the existing spinlock and also by avoiding the
access to timer during close call.
While performing hw_free, DPCM checks the BE state but leaves out
the suspend state. The suspend state needs to be checked as well,
as we might be suspended and then usermode closes rather than
resuming the audio stream.
This was found by a stress testing of system with playback in
loop and killed after few seconds running in background and second
script running suspend-resume test in loop
Signed-off-by: Vinod Koul <vinod.koul@intel.com> Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are potential deadlocks in PCM OSS emulation code while
accessing read/write and mmap concurrently. This comes from the
infamous mmap_sem usage in copy_from/to_user(). Namely,
The rawmidi read and write functions manage runtime stream status
such as runtime->appl_ptr and runtime->avail. These point where to
copy the new data and how many bytes have been copied (or to be
read). The problem is that rawmidi read/write call copy_from_user()
or copy_to_user(), and the runtime spinlock is temporarily unlocked
and relocked while copying user-space. Since the current code
advances and updates the runtime status after the spin unlock/relock,
the copy and the update may be asynchronous, and eventually
runtime->avail might go to a negative value when many concurrent
accesses are done. This may lead to memory corruption in the end.
For fixing this race, in this patch, the status update code is
performed in the same lock before the temporary unlock. Also, the
spinlock is now taken more widely in snd_rawmidi_kernel_read1() for
protecting more properly during the whole operation.
NULL user-space buffer can be passed even in a normal path, thus it's
not good to spew a kernel warning with stack trace at each time.
Just drop snd_BUG_ON() macro usage there.
ALSA sequencer OSS emulation code has a sanity check for currently
opened devices, but there is a thinko there, eventually it spews
warnings and skips the operation wrongly like:
WARNING: CPU: 1 PID: 7573 at sound/core/seq/oss/seq_oss_synth.c:311
ALSA dummy driver can switch the timer backend between system timer
and hrtimer via its hrtimer module option. This can be also switched
dynamically via sysfs, but it may lead to a memory corruption when
switching is done while a PCM stream is running; the stream instance
for the newly switched timer method tries to access the memory that
was allocated by another timer method although the sizes differ.
As the simplest fix, this patch just disables the switch via sysfs by
dropping the writable bit.
Some architectures like PowerPC can handle the maximum struct size in
an ioctl only up to 13 bits, and struct snd_compr_codec_caps used by
SNDRV_COMPRESS_GET_CODEC_CAPS ioctl overflows this limit. This
problem was revealed recently by a powerpc change, as it's now treated
as a fatal build error.
This patch is a stop-gap for that: for architectures with less than 14
bit ioctl struct size, get rid of the handling of the relevant ioctl.
We should provide an alternative equivalent ioctl code later, but for
now just paper over it. Luckily, the compress API hasn't been used on
such architectures, so the impact must be effectively zero.
Reviewed-by: Mark Brown <broonie@kernel.org> Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'umidi' object will be free'd on the error path by snd_usbmidi_free()
when tearing down the rawmidi interface. So we shouldn't try to free it
in snd_usbmidi_create() after having registered the rawmidi interface.
TEAC UD-501/UD-503/NT-503 fail to switch properly between different
rate/format. Similar to 'Playback Design', this patch corrects the
invalid clock source error for TEAC products and avoids complete
freeze of the usb interface of 503 series.
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In videobuf2 dma-contig memory type the prepare and finish ops, instead of
passing the number of entries in the original scatterlist as the "nents"
parameter to dma_sync_sg_for_device() and dma_sync_sg_for_cpu(), the value
returned by dma_map_sg() was used. Albeit this has been suggested in
comments of some implementations (which have since been corrected), this
is wrong.
Fixes: 199d101efdba ("v4l: vb2-dma-contig: add prepare/finish to dma-contig allocator") Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alignment/padding rules on AMD64 and ARM64 differs. To allow properly match
compatible ioctls on ARM64 kernels without breaking AMD64 some fields
should be aligned using compat_s64 type and in one case struct should be
unpacked.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
[hans.verkuil@cisco.com: use compat_u64 instead of compat_s64 in v4l2_input32] Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On a 64bit kernel build the compiler aligns the _sifields union in the
struct siginfo_t on a 64bit address. The __ARCH_SI_PREAMBLE_SIZE define
compensates for this alignment and thus fixes the wait testcase of the
strace package.
The symptoms of a wrong __ARCH_SI_PREAMBLE_SIZE value is that
_sigchld.si_stime variable is missed to be copied and thus after a
copy_siginfo() will have uninitialized values.
On parisc syscalls which are interrupted by signals sometimes failed to
restart and instead returned -ENOSYS which in the worst case lead to
userspace crashes.
A similiar problem existed on MIPS and was fixed by commit e967ef02
("MIPS: Fix restart of indirect syscalls").
On parisc the current syscall restart code assumes that all syscall
callers load the syscall number in the delay slot of the ble
instruction. That's how it is e.g. done in the unistd.h header file:
ble 0x100(%sr2, %r0)
ldi #syscall_nr, %r20
Because of that assumption the current code never restored %r20 before
returning to userspace.
This assumption is at least not true for code which uses the glibc
syscall() function, which instead uses this syntax:
ble 0x100(%sr2, %r0)
copy regX, %r20
where regX depend on how the compiler optimizes the code and register
usage.
This patch fixes this problem by adding code to analyze how the syscall
number is loaded in the delay branch and - if needed - copy the syscall
number to regX prior returning to userspace for the syscall restart.
"group" is the group where the backup will be placed, and is
initialized to zero in the declaration. This meant that backups for
meta_bg descriptors were erroneously written to the backup block group
descriptors in groups 1 and (desc_per_block-1).
Ted and Namjae have reported that truncated pages don't get timely
reclaimed after being truncated in data=journal mode. The following test
triggers the issue easily:
for (i = 0; i < 1000; i++) {
pwrite(fd, buf, 1024*1024, 0);
fsync(fd);
fsync(fd);
ftruncate(fd, 0);
}
The reason is that journal_unmap_buffer() finds that truncated buffers
are not journalled (jh->b_transaction == NULL), they are part of
checkpoint list of a transaction (jh->b_cp_transaction != NULL) and have
been already written out (!buffer_dirty(bh)). We clean such buffers but
we leave them in the checkpoint list. Since checkpoint transaction holds
a reference to the journal head, these buffers cannot be released until
the checkpoint transaction is cleaned up. And at that point we don't
call release_buffer_page() anymore so pages detached from mapping are
lingering in the system waiting for reclaim to find them and free them.
Fix the problem by removing buffers from transaction checkpoint lists
when journal_unmap_buffer() finds out they don't have to be there
anymore.
Reported-and-tested-by: Namjae Jeon <namjae.jeon@samsung.com> Fixes: de1b794130b130e77ffa975bb58cb843744f9ae5 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At ibm vtpm initialzation, tpm_ibmvtpm_probe() registers its interrupt
handler, ibmvtpm_interrupt, which calls ibmvtpm_crq_process to allocate
memory for rtce buffer. The current code uses 'GFP_KERNEL' as the
type of kernel memory allocation, which resulted a warning at
kernel/lockdep.c. This patch uses 'GFP_ATOMIC' instead so that the
allocation is high-priority and does not sleep.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the below Oops when trying to modprobe wlcore_spi.
The oops occurs because the wl1271_power_{off,on}()
function doesn't check the power() function pointer.
[ 23.665030] [<bf2581f0>] (wl12xx_set_power_on [wlcore]) from
[<bf25f7ac>] (wlcore_nvs_cb+0x118/0xa4c [wlcore])
[ 23.675604] [<bf25f7ac>] (wlcore_nvs_cb [wlcore]) from [<c04387ec>]
(request_firmware_work_func+0x30/0x58)
[ 23.685784] [<c04387ec>] (request_firmware_work_func) from
[<c0058e2c>] (process_one_work+0x1b4/0x4b4)
[ 23.695591] [<c0058e2c>] (process_one_work) from [<c0059168>]
(worker_thread+0x3c/0x4a4)
[ 23.704124] [<c0059168>] (worker_thread) from [<c005ee68>]
(kthread+0xd4/0xf0)
[ 23.711747] [<c005ee68>] (kthread) from [<c000f598>]
(ret_from_fork+0x14/0x3c)
[ 23.719357] Code: bad PC value
[ 23.722760] ---[ end trace 981be8510db9b3a9 ]---
Prevent oops by validationg power() pointer value before
calling the function.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum chunks used by the function is
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE + 1).
The original commands array had space for
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) commands.
When the last chunk is used (len > 4 * WSPI_MAX_CHUNK_SIZE), the last
command is stored outside the bounds of the commands array.
Oops 5 (page fault) is generated during current wl1271 firmware load
attempt:
root@debian-armhf:~# ifconfig wlan0 up
[ 294.312399] Unable to handle kernel paging request at virtual address 00203fc4
[ 294.320173] pgd = de528000
[ 294.323028] [00203fc4] *pgd=00000000
[ 294.326916] Internal error: Oops: 5 [#1] SMP ARM
[ 294.331789] Modules linked in: bnep rfcomm bluetooth ipv6 arc4 wl12xx
wlcore mac80211 musb_dsps cfg80211 musb_hdrc usbcore usb_common
wlcore_spi omap_rng rng_core musb_am335x omap_wdt cpufreq_dt thermal_sys
hwmon
[ 294.351838] CPU: 0 PID: 1827 Comm: ifconfig Not tainted 4.2.0-00002-g3e9ad27-dirty #78
[ 294.360154] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 294.366557] task: dc9d6d40 ti: de550000 task.ti: de550000
[ 294.372236] PC is at __spi_validate+0xa8/0x2ac
[ 294.376902] LR is at __spi_sync+0x78/0x210
[ 294.381200] pc : [<c049c760>] lr : [<c049ebe0>] psr: 60000013
[ 294.381200] sp : de551998 ip : de5519d8 fp : 00200000
[ 294.393242] r10: de551c8c r9 : de5519d8 r8 : de3a9000
[ 294.398730] r7 : de3a9258 r6 : de3a9400 r5 : de551a48 r4 : 00203fbc
[ 294.405577] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : de3a9000
[ 294.412420] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 294.419918] Control: 10c5387d Table: 9e528019 DAC: 00000015
[ 294.425954] Process ifconfig (pid: 1827, stack limit = 0xde550218)
[ 294.432437] Stack: (0xde551998 to 0xde552000)
...
[ 294.883613] [<c049c760>] (__spi_validate) from [<c049ebe0>]
(__spi_sync+0x78/0x210)
[ 294.891670] [<c049ebe0>] (__spi_sync) from [<bf036598>]
(wl12xx_spi_raw_write+0xfc/0x148 [wlcore_spi])
[ 294.901661] [<bf036598>] (wl12xx_spi_raw_write [wlcore_spi]) from
[<bf21c694>] (wlcore_boot_upload_firmware+0x1ec/0x458 [wlcore])
[ 294.914038] [<bf21c694>] (wlcore_boot_upload_firmware [wlcore]) from
[<bf24532c>] (wl12xx_boot+0xc10/0xfac [wl12xx])
[ 294.925161] [<bf24532c>] (wl12xx_boot [wl12xx]) from [<bf20d5cc>]
(wl1271_op_add_interface+0x5b0/0x910 [wlcore])
[ 294.936364] [<bf20d5cc>] (wl1271_op_add_interface [wlcore]) from
[<bf15c4ac>] (ieee80211_do_open+0x44c/0xf7c [mac80211])
[ 294.947963] [<bf15c4ac>] (ieee80211_do_open [mac80211]) from
[<c0537978>] (__dev_open+0xa8/0x110)
[ 294.957307] [<c0537978>] (__dev_open) from [<c0537bf8>]
(__dev_change_flags+0x88/0x148)
[ 294.965713] [<c0537bf8>] (__dev_change_flags) from [<c0537cd0>]
(dev_change_flags+0x18/0x48)
[ 294.974576] [<c0537cd0>] (dev_change_flags) from [<c05a55a0>]
(devinet_ioctl+0x6b4/0x7d0)
[ 294.983191] [<c05a55a0>] (devinet_ioctl) from [<c0517040>]
(sock_ioctl+0x1e4/0x2bc)
[ 294.991244] [<c0517040>] (sock_ioctl) from [<c017d378>]
(do_vfs_ioctl+0x420/0x6b0)
[ 294.999208] [<c017d378>] (do_vfs_ioctl) from [<c017d674>]
(SyS_ioctl+0x6c/0x7c)
[ 295.006880] [<c017d674>] (SyS_ioctl) from [<c000f4c0>]
(ret_fast_syscall+0x0/0x54)
[ 295.014835] Code: e1550004e24440340a00007de5953018 (e5942008)
[ 295.021544] ---[ end trace 66ed188198f4e24e ]---
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix parent-device reference leak due to SPI-core taking an unnecessary
reference to the parent when allocating the master structure, a
reference that was never released.
Note that driver core takes its own reference to the parent when the
master device is registered.
Fixes: 49dce689ad4e ("spi doesn't need class_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA-slave configuration depends on the whether <= 8 or > 8 bits
are transferred per word, so we need to call
atmel_spi_dma_slave_config() with the correct value.
Signed-off-by: David Mosberger <davidm@egauge.net> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That commit introduced a regression at least for the case of the SG_IO ioctl()
running without CAP_SYS_RAWIO capability (e.g., unprivileged users) when there
are no active paths: the ioctl() fails with the ENOTTY errno immediately rather
than blocking due to queue_if_no_path until a path becomes active, for example.
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2])
from multipath devices; which leads to SCSI/filesystem errors in such a guest.
More general scenarios can hit that regression too. The following demonstration
employs a SG_IO ioctl() with a standard SCSI INQUIRY command for this objective
(some output & user changes omitted for brevity and comments added for clarity).
Reverting that commit restores normal operation (queueing) in failing scenarios;
tested on linux-next (next-20151022).
1) Test-case is based on sg_simple0 [3] (just SG_IO; remove SG_GET_VERSION_NUM)
$ cat sg_simple0.c
... see [3] ...
$ sed '/SG_GET_VERSION_NUM/,/}/d' sg_simple0.c > sgio_inquiry.c
$ gcc sgio_inquiry.c -o sgio_inquiry
2) The ioctl() works fine with active paths present.
5) The ioctl() only works if the SYS_CAP_RAWIO capability is present
(then queueing happens -- in this example, queue_if_no_path is set);
this is due to a conditional check in scsi_verify_blk_ioctl().
According to arch/sh/kernel/syscalls_64.S and common sense, __NR_fgetxattr
has to be defined to 259, but it doesn't. Instead, it's defined to 269,
which is of course used by another syscall, __NR_sched_setaffinity in this
case.
When recovery master down, dlm_do_local_recovery_cleanup() only remove
the $RECOVERY lock owned by dead node, but do not clear the refmap bit.
Which will make umount thread falling in dead loop migrating $RECOVERY
to the dead node.
Signed-off-by: xuejiufei <xuejiufei@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have found that migration source will trigger a BUG that the refcount
of mle is already zero before put when the target is down during
migration. The situation is as follows:
dlm_migrate_lockres
dlm_add_migration_mle
dlm_mark_lockres_migrating
dlm_get_mle_inuse
<<<<<< Now the refcount of the mle is 2.
dlm_send_one_lockres and wait for the target to become the
new master.
<<<<<< o2hb detect the target down and clean the migration
mle. Now the refcount is 1.
dlm_migrate_lockres woken, and put the mle twice when found the target
goes down which trigger the BUG with the following message:
"ERROR: bad mle: ".
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sigsuspend() is nowhere used except in signal.c itself, so we can mark it
static do not pollute the global namespace.
But this patch is more than a boring cleanup patch, it fixes a real issue
on UserModeLinux. UML has a special console driver to display ttys using
xterm, or other terminal emulators, on the host side. Vegard reported
that sometimes UML is unable to spawn a xterm and he's facing the
following warning:
WARNING: CPU: 0 PID: 908 at include/linux/thread_info.h:128 sigsuspend+0xab/0xc0()
It turned out that this warning makes absolutely no sense as the UML
xterm code calls sigsuspend() on the host side, at least it tries. But
as the kernel itself offers a sigsuspend() symbol the linker choose this
one instead of the glibc wrapper. Interestingly this code used to work
since ever but always blocked signals on the wrong side. Some recent
kernel change made the WARN_ON() trigger and uncovered the bug.
It is a wonderful example of how much works by chance on computers. :-)
Recent gcc versions warn about reading from a negative offset of
an on-stack array:
drivers/remoteproc/remoteproc_debugfs.c: In function 'rproc_recovery_write':
drivers/remoteproc/remoteproc_debugfs.c:167:9: warning: 'buf[4294967295u]' may be used uninitialized in this function [-Wmaybe-uninitialized]
I don't see anything in sys_write() that prevents us from
being called with a zero 'count' argument, so we should
add an extra check in rproc_recovery_write() to prevent the
access and avoid the warning.
The critical section protected by usbhid->lock in hid_ctrl() is too
big and because of this it causes a recursive deadlock. "Too big" means
the case statement and the call to hid_input_report() do not need to be
protected by the spinlock (no URB operations are done inside them).
The deadlock happens because in certain rare cases drivers try to grab
the lock while handling the ctrl irq which grabs the lock before them
as described above. For example newer wacom tablets like 056a:033c try
to reschedule proximity reads from wacom_intuos_schedule_prox_event()
calling hid_hw_request() -> usbhid_request() -> usbhid_submit_report()
which tries to grab the usbhid lock already held by hid_ctrl().
There are two ways to get out of this deadlock:
1. Make the drivers work "around" the ctrl critical region, in the
wacom case for ex. by delaying the scheduling of the proximity read
request itself to a workqueue.
2. Shrink the critical region so the usbhid lock protects only the
instructions which modify usbhid state, calling hid_input_report()
with the spinlock unlocked, allowing the device driver to grab the
lock first, finish and then grab the lock afterwards in hid_ctrl().
In the backport of 1eaf35e4dd592c59041bc1ed3248c46326da1f5f, the call to
usb_disabled() was too late, after we had already done some allocation.
Move that call to the top of the function instead, making the logic
match what is intended and is in the original patch.
Reported-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In nop_mcount, shdr->sh_offset and welp->r_offset should handle
endianness properly, otherwise it will trigger Segmentation fault
if the recordmcount main and file.o have different endianness.
Link: http://lkml.kernel.org/r/563806C7.7070606@huawei.com Signed-off-by: Li Bin <huawei.libin@huawei.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>