In __rtc_read_alarm(), if the alarm time retrieved by
rtc_read_alarm_internal() from the device contains invalid values (e.g.
month=2,mday=31) and the year not set (=-1), the initialization will
loop infinitely because the year-fixing loop expects the time being
invalid due to leap year.
Fix reduces the loop to the leap years and adds final validity check.
In particular seeing zero in eft->month is problematic, as it results in
-1 (converted to unsigned int, i.e. yielding 0xffffffff) getting passed
to rtc_year_days(), where the value gets used as an array index
(normally resulting in a crash). This was observed with the driver
enabled on x86 on some Fujitsu system (with possibly not up to date
firmware, but anyway).
Perhaps efi_read_alarm() should not fail if neither enabled nor pending
are set, but the returned time is invalid?
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reported-by: Raymund Will <rw@suse.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jingoo Han <jg1.han@samsung.com> Acked-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Compared source code of rtc-lib.c::rtc_year_days() with
efirtc.c::rtc_year_days(), found the code in rtc-efi decreases value of
day twice when it computing year days. rtc-lib.c::rtc_year_days() has
already decrease days and return the year days from 0 to 365.
This fix (not very clean though) should fix the long time USB3
issue that was spotted last year. The rational has been given by
Hans de Goede:
----
I think the most likely cause for this is a firmware bug
in the unifying receiver, likely a race condition.
The most prominent difference between having a USB-2 device
plugged into an EHCI (so USB-2 only) port versus an XHCI
port will be inter packet timing. Specifically if you
send packets (ie hid reports) one at a time, then with
the EHCI controller their will be a significant pause
between them, where with XHCI they will be very close
together in time.
The reason for this is the difference in EHCI / XHCI
controller OS <-> driver interfaces.
For non periodic endpoints (control, bulk) the EHCI uses a
circular linked-list of commands in dma-memory, which it
follows to execute commands, if the list is empty, it
will go into an idle state and re-check periodically.
The XHCI uses a ring of commands per endpoint, and if the OS
places anything new on the ring it will do an ioport write,
waking up the XHCI making it send the new packet immediately.
For periodic transfers (isoc, interrupt) the delay between
packets when sending one at a time (rather then queuing them
up) will be even larger, because they need to be inserted into
the EHCI schedule 2 ms in the future so the OS driver can be
sure that the EHCI driver does not try to start executing the
time slot in question before the insertion has completed.
So a possible fix may be to insert a delay between packets
being send to the receiver.
----
I tested this on a buggy Haswell USB 3.0 motherboard, and I always
get the notification after adding the msleep.
Numerical values stored in the device tree are encoded in Big Endian and
should be byte swapped when running in Little Endian.
The RPA hotplug module should convert those values as well.
Note that in rpaphp_get_drc_props(), the comparison between indexes[i+1]
and *index is done using the BE values (whatever is the current endianess).
This doesn't matter since we are checking for equality here. This way only
the returned value is byte swapped.
RPA also made RTAS calls which implies BE values to be used. According to
the patch done in RTAS (http://patchwork.ozlabs.org/patch/336865), no
additional conversion is required in RPA.
tipc_msg_build() calls skb_copy_to_linear_data_offset() to copy data
from user space to kernel space. However, the latter function does
in its turn call memcpy() to perform the actual copying. This poses
an obvious security and robustness risk, since memcpy() never makes
any validity check on the pointer it is copying from.
To correct this, we the replace the offending function call with
a call to memcpy_fromiovecend(), which uses copy_from_user() to
perform the copying.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch adds support for 57764, 57765, 57787, 57782 and 57786
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since commit 3fb43eb ("bnx2x: Change to D3hot only on removal") nvram
is accessible whenever the driver is loaded - Thus it is possible to
test it during self-test even if the interface is down
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The cpl_abort_req struct has several reserved members which need to be
cleared to avoid disclosing kernel information. I have added a memset()
so now it matches the cxgb4 version of this function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
*using_dac = true;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err)
goto release_regions;
}
This means we only try and set the coherent DMA mask if we failed to
set a 32-bit DMA mask, and only if both fail do we fail the driver.
Adjust this so that if either setting fails, we fail the driver - and
thereby end up properly setting both the DMA mask and the coherent
DMA mask in the fallback case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If new_mtu is very large then "new_mtu + ETH_HLEN + ETH_FCS_LEN" can
wrap and the check on the next line can underflow. This is one of those
bugs which can be triggered by the user if you have namespaces
configured.
Also since this is something the user can trigger then we don't want to
have dev_err() message.
This is a static checker fix and I'm not sure what the impact is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Sibai Li Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev, "No usable DMA "
"configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit fa44f2f185f7f9da19d331929bb1b56c1ccd1d93 broke reloading of igb, when
VFs are assigned to a guest, in several ways.
1. on module load adapter->vf_data does not get properly allocated,
resulting in a null pointer exception when accessing adapter->vf_data in
igb_reset() on module reload.
modprobe -r igb ; modprobe igb max_vfs=7
[ 215.215837] igb 0000:01:00.1: removed PHC on eth1
[ 216.932072] igb 0000:01:00.1: IOV Disabled
[ 216.937038] igb 0000:01:00.0: removed PHC on eth0
[ 217.127032] igb 0000:01:00.0: Cannot deallocate SR-IOV virtual functions while they are assigned - VFs will not be deallocated
[ 217.146178] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
[ 217.154050] igb: Copyright (c) 2007-2013 Intel Corporation.
[ 217.160688] igb 0000:01:00.0: Enabling SR-IOV VFs using the module parameter is deprecated - please use the pci sysfs interface.
[ 217.173703] igb 0000:01:00.0: irq 103 for MSI/MSI-X
[ 217.179227] igb 0000:01:00.0: irq 104 for MSI/MSI-X
[ 217.184735] igb 0000:01:00.0: irq 105 for MSI/MSI-X
[ 217.220082] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 217.228846] IP: [<ffffffffa007c5e5>] igb_reset+0xc5/0x4b0 [igb]
[ 217.235472] PGD 3607ec067 PUD 36170b067 PMD 0
[ 217.240461] Oops: 0002 [#1] SMP
[ 217.244085] Modules linked in: igb(+) igbvf mptsas mptscsih mptbase scsi_transport_sas [last unloaded: igb]
[ 217.255040] CPU: 4 PID: 4833 Comm: modprobe Not tainted 3.11.0+ #46
[...]
[ 217.390007] [<ffffffffa007fab2>] igb_probe+0x892/0xfd0 [igb]
[ 217.396422] [<ffffffff81470b3e>] local_pci_probe+0x1e/0x40
[ 217.402641] [<ffffffff81472029>] pci_device_probe+0xf9/0x110
[...]
2. A follow up issue, pci_enable_sriov() should only be called if no VFs were
still allocated on module unload. Otherwise pci_enable_sriov() gets called
multiple times in a row rendering the NIC unusable until reset.
3. simply calling igb_enable_sriov() in igb_probe_vfs() is not enough as the
interrupts need to be re-setup. Switching that to igb_pci_enable_sriov().
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Tested-by: Sibai Li <Sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch calls code to set the master/slave mode for all m88 gen 2
PHY's. This patch also removes the call to this function for I210 devices
only from the function that is not called by I210 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since we are already checking for read failure in check_link we don't need
to do it here. Instead just make sure the watchdog task gets scheduled, if
we are up, and it can be done there. This will better follow igbvf method
of handling a mailbox event and message timeout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev, "No usable DMA "
"configuration, aborting\n");
goto err_dma;
}
}
pci_using_dac = 0;
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch resolves an issue where the MTA table can be cleared when the
interface is reset while in promisc mode. As result IPv6 traffic between
VFs will be interrupted.
This patch makes the update of the MTA table unconditional to avoid the
inconsistent clearing on reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ixgbe_napi_disable_all calls napi_disable on each queue, however the busy
polling code introduced a local_bh_disable()d context around the napi_disable.
The original author did not realize that napi_disable might sleep, which would
cause a sleep while atomic BUG. In addition, on a single processor system, the
ixgbe_qv_lock_napi loop shouldn't have to mdelay. This patch adds an
ixgbe_qv_disable along with a new IXGBE_QV_STATE_DISABLED bit, which it uses to
indicate to the poll and napi routines that the q_vector has been disabled. Now
the ixgbe_napi_disable_all function will wait until all pending work has been
finished and prevent any future work from being started.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: Alexander Duyck <alexander.duyck@intel.com> Cc: Hyong-Youb Kim <hykim@myri.com> Cc: Amir Vadai <amirv@mellanox.com> Cc: Dmitry Kravkov <dmitry@broadcom.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch resolves an issue where the logic used to detect changes in rx-usecs
was incorrect and was masked by the call to ixgbe_update_rsc().
Setting rx-usecs between 0,2-9 and 1,10 and up requires a reset to allow
ixgbe_configure_tx_ring() to set the correct value for TXDCTL.WTHRESH in
order to avoid Tx hangs with BQL enabled.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
!dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
pci_using_dac = 0;
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This change is based on a similar change made to e1000e support in
commit bb9e44d0d0f4 ("e1000e: prevent oops when adapter is being closed
and reset simultaneously"). The same issue has also been observed
on the older e1000 cards.
Here, we have increased the RESET_COUNT value to 50 because there are too
many accesses to e1000 nic on stress tests to e1000 nic, it is not enough
to set RESET_COUT 25. Experimentation has shown that it is enough to set
RESET_COUNT 50.
Signed-off-by: yzhu1 <yanjun.zhu@windriver.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 7509963c703b (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:
drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]
drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]
To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Dave Ertman <davidx.m.ertman@intel.com> Cc: Aaron Brown <aaron.f.brown@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Provide a helper to set both the DMA and coherent DMA masks to the
same value - this avoids duplicated code in a number of drivers,
sometimes with buggy error handling, and also allows us identify
which drivers do things differently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When FB_EVENT_FB_UNBIND is sent, fbcon has two paths, one path taken
when there is another frame buffer to switch any affected vcs to and
another path when there isn't.
In the case where there is another frame buffer to use,
fbcon_fb_unbind calls set_con2fb_map to remap all of the affected vcs
to the replacement frame buffer. set_con2fb_map will eventually call
con2fb_release_oldinfo when the last vcs gets unmapped from the old
frame buffer.
con2fb_release_oldinfo frees the fbcon data that is hooked off of the
fb_info structure, including the cursor timer.
In the case where there isn't another frame buffer to use,
fbcon_fb_unbind simply calls fbcon_unbind, which doesn't clear the
con2fb_map or free the fbcon data hooked from the fb_info
structure. In particular, it doesn't stop the cursor blink timer. When
the fb_info structure is then freed, we end up with a timer queue
pointing into freed memory and "bad things" start happening.
This patch first changes con2fb_release_oldinfo so that it can take a
NULL pointer for the new frame buffer, but still does all of the
deallocation and cursor timer cleanup.
Finally, the patch tries to replicate some of what set_con2fb_map does
by clearing the con2fb_map for the affected vcs and calling the
modified con2fb_release_info function to clean up the fb_info structure.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
free_holes_block() passed local variable as a block pointer
to ext4_clear_blocks(). Thus ext4_clear_blocks() zeroed out this local
variable instead of proper place in inode / indirect block. We later
zero out proper place in inode / indirect block but don't dirty the
inode / buffer again which can lead to subtle issues (some changes e.g.
to inode can be lost).
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
While invesgiating the issue where in "mount --bind -oremount,ro ..."
would result in later "mount --bind -oremount,rw" succeeding even if
the mount started off locked I realized that there are several
additional mount flags that should be locked and are not.
In particular MNT_NOSUID, MNT_NODEV, MNT_NOEXEC, and the atime
flags in addition to MNT_READONLY should all be locked. These
flags are all per superblock, can all be changed with MS_BIND,
and should not be changable if set by a more privileged user.
The following additions to the current logic are added in this patch.
- nosuid may not be clearable by a less privileged user.
- nodev may not be clearable by a less privielged user.
- noexec may not be clearable by a less privileged user.
- atime flags may not be changeable by a less privileged user.
The logic with atime is that always setting atime on access is a
global policy and backup software and auditing software could break if
atime bits are not updated (when they are configured to be updated),
and serious performance degradation could result (DOS attack) if atime
updates happen when they have been explicitly disabled. Therefore an
unprivileged user should not be able to mess with the atime bits set
by a more privileged user.
The additional restrictions are implemented with the addition of
MNT_LOCK_NOSUID, MNT_LOCK_NODEV, MNT_LOCK_NOEXEC, and MNT_LOCK_ATIME
mnt flags.
Taken together these changes and the fixes for MNT_LOCK_READONLY
should make it safe for an unprivileged user to create a user
namespace and to call "mount --bind -o remount,... ..." without
the danger of mount flags being changed maliciously.
Cc: stable@vger.kernel.org Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There are no races as locked mount flags are guaranteed to never change.
Moving the test into do_remount makes it more visible, and ensures all
filesystem remounts pass the MNT_LOCK_READONLY permission check. This
second case is not an issue today as filesystem remounts are guarded
by capable(CAP_DAC_ADMIN) and thus will always fail in less privileged
mount namespaces, but it could become an issue in the future.
Cc: stable@vger.kernel.org Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Kenton Varda <kenton@sandstorm.io> discovered that by remounting a
read-only bind mount read-only in a user namespace the
MNT_LOCK_READONLY bit would be cleared, allowing an unprivileged user
to the remount a read-only mount read-write.
Correct this by replacing the mask of mount flags to preserve
with a mask of mount flags that may be changed, and preserve
all others. This ensures that any future bugs with this mask and
remount will fail in an easy to detect way where new mount flags
simply won't change.
Cc: stable@vger.kernel.org Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 4a705fef9862 ("hugetlb: fix copy_hugetlb_page_range() to handle
migration/hwpoisoned entry") changed the order of
huge_ptep_set_wrprotect() and huge_ptep_get(), which leads to breakage
in some workloads like hugepage-backed heap allocation via libhugetlbfs.
This patch fixes it.
Fixes 4a705fef9862 ("hugetlb: fix copy_hugetlb_page_range() to handle
migration/hwpoisoned entry"), so is applicable to -stable kernels which
include it.
There's a race between fork() and hugepage migration, as a result we try
to "dereference" a swap entry as a normal pte, causing kernel panic.
The cause of the problem is that copy_hugetlb_page_range() can't handle
"swap entry" family (migration entry and hwpoisoned entry) so let's fix
it.
In case of beacon_loss with IEEE80211_HW_CONNECTION_MONITOR
device, mac80211 probes the ap (and disconnects on timeout)
but ignores the ack.
If we already got an ack, there's no reason to continue
disconnecting. this can help devices that supports
IEEE80211_HW_CONNECTION_MONITOR only partially (e.g. take
care of keep alives, but does not probe the ap.
In case the device wants to disconnect without probing,
it can just call ieee80211_connection_loss.
Instead of always calling ieee80211_beacon_loss() on every missed
beacons notification, call this function only if the number of
consecutive missed beacons from last rx is higher than a predefined
threshold.
This commit is a guesswork, but it seems to make sense to drop this
break, as otherwise the following line is never executed and becomes
dead code. And that following line actually saves the result of
local calculation by the pointer given in function argument. So the
proposed change makes sense if this code in the whole makes sense (but I
am unable to analyze it in the whole).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81641 Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The LDC handshake could have been asynchronously triggered
after ldc_bind() enables the ldc_rx() receive interrupt-handler
(and thus intercepts incoming control packets)
and before vio_port_up() calls ldc_connect(). If that is the case,
ldc_connect() should return 0 and let the state-machine
progress.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Karl Volz <karl.volz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix detection of BREAK on sunsab serial console: BREAK detection was only
performed when there were also serial characters received simultaneously.
To handle all BREAKs correctly, the check for BREAK and the corresponding
call to uart_handle_break() must also be done if count == 0, therefore
duplicate this code fragment and pull it out of the loop over the received
characters.
Patch applies to 3.16-rc6.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix regression in bbc i2c temperature and fan control on some Sun systems
that causes the driver to refuse to load due to the bbc_i2c_bussel resource not
being present on the (second) i2c bus where the temperature sensors and fan
control are located. (The check for the number of resources was removed when
the driver was ported to a pure OF driver in mid 2008.)
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Based almost entirely upon a patch by Christopher Alexander Tobias
Schulze.
In commit db64fe02258f1507e13fe5212a989922323685ce ("mm: rewrite vmap
layer") lazy VMAP tlb flushing was added to the vmalloc layer. This
causes problems on sparc64.
Sparc64 has two VMAP mapped regions and they are not contiguous with
eachother. First we have the malloc mapping area, then another
unrelated region, then the vmalloc region.
This "another unrelated region" is where the firmware is mapped.
If the lazy TLB flushing logic in the vmalloc code triggers after
we've had both a module unload and a vfree or similar, it will pass an
address range that goes from somewhere inside the malloc region to
somewhere inside the vmalloc region, and thus covering the
openfirmware area entirely.
The sparc64 kernel learns about openfirmware's dynamic mappings in
this region early in the boot, and then services TLB misses in this
area. But openfirmware has some locked TLB entries which are not
mentioned in those dynamic mappings and we should thus not disturb
them.
These huge lazy TLB flush ranges causes those openfirmware locked TLB
entries to be removed, resulting in all kinds of problems including
hard hangs and crashes during reboot/reset.
Besides causing problems like this, such huge TLB flush ranges are
also incredibly inefficient. A plea has been made with the author of
the VMAP lazy TLB flushing code, but for now we'll put a safety guard
into our flush_tlb_kernel_range() implementation.
Since the implementation has become non-trivial, stop defining it as a
macro and instead make it a function in a C source file.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.
This is not true for code paths originating from remove_migration_pte().
There are dire consequences for placing a non-valid PTE into the TSB. The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.
So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.
Just exit early from update_mmu_cache() and friends in this situation.
Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Access to the TSB hash tables during TLB misses requires that there be
an atomic 128-bit quad load available so that we fetch a matching TAG
and DATA field at the same time.
On cpus prior to UltraSPARC-III only virtual address based quad loads
are available. UltraSPARC-III and later provide physical address
based variants which are easier to use.
When we only have virtual address based quad loads available this
means that we have to lock the TSB into the TLB at a fixed virtual
address on each cpu when it runs that process. We can't just access
the PAGE_OFFSET based aliased mapping of these TSBs because we cannot
take a recursive TLB miss inside of the TLB miss handler without
risking running out of hardware trap levels (some trap combinations
can be deep, such as those generated by register window spill and fill
traps).
Without huge pages it's working perfectly fine, but when the huge TSB
got added another chunk of fixed virtual address space was not
allocated for this second TSB mapping.
So we were mapping both the 8K and 4MB TSBs to the same exact virtual
address, causing multiple TLB matches which gives undefined behavior.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a user process which is 32-bit performs a load or a store, the
cpu chops off the top 32-bits of the effective address before
translating it.
This is because we run 32-bit tasks with the PSTATE_AM (address
masking) bit set.
We can't run the kernel with that bit set, so when the kernel accesses
userspace no address masking occurs.
Since a 32-bit process will have no mappings in that region we will
properly fault, so we don't try to handle this using access_ok(),
which can safely just be a NOP on sparc64.
Real faults from 32-bit processes should never generate such addresses
so a bug check was added long ago, and it barks in the logs if this
happens.
But it also barks when a kernel user access causes this condition, and
that _can_ happen. For example, if a pointer passed into a system call
is "0xfffffffc" and the kernel access 4 bytes offset from that pointer.
Just handle such faults normally via the exception entries.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
For pgd_ERROR() and pmd_ERROR(), output something similar to x86, giving the address
of the pgd/pmd as well as it's value.
Also provide the caller, since these macros are invoked from pgd_clear_bad() and
pmd_clear_bad() which provides little context as to what high level operation was
occuring when the BAD state was detected.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Next, make do_fault_siginfo() more robust when get_user_insn() can't
actually fetch the instruction. In particular, use the MMU announced
fault address when that happens, instead of calling
compute_effective_address() and computing garbage.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This is a followup of commits f1d8cba61c3c4b ("inet: fix possible
seqlock deadlocks") and 7f88c6b23afbd315 ("ipv6: fix possible seqlock
deadlock in ip6_finish_output2")
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Dave Jones <davej@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When performing segmentation, the mac_len value is copied right
out of the original skb. However, this value is not always set correctly
(like when the packet is VLAN-tagged) and we'll end up copying a bad
value.
One way to demonstrate this is to configure a VM which tags
packets internally and turn off VLAN acceleration on the forwarding
bridge port. The packets show up corrupt like this:
16:18:24.985548 52:54:00:ab:be:25 > 52:54:00:26:ce:a3, ethertype 802.1Q
(0x8100), length 1518: vlan 100, p 0, ethertype 0x05e0,
0x0000: 8cdb 1c7c 8cdb 0064 4006 b59d 0a00 6402 ...|...d@.....d.
0x0010: 0a00 6401 9e0d b441 0a5e 64ec 0330 14fa ..d....A.^d..0..
0x0020: 29e3 01c9 f871 0000 0101 080a 000a e833)....q.........3
0x0030: 000f 8c75 6e65 7470 6572 6600 6e65 7470 ...unetperf.netp
0x0040: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0050: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0060: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
...
This also leads to awful throughput as GSO packets are dropped and
cause retransmissions.
The solution is to set the mac_len using the values already available
in then new skb. We've already adjusted all of the header offset, so we
might as well correctly figure out the mac_len using skb_reset_mac_len().
After this change, packets are segmented correctly and performance
is restored.
CC: Eric Dumazet <edumazet@google.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macvlan devices do not initialize vlan_features. As a result,
any vlan devices configured on top of macvlans perform very poorly.
Initialize vlan_features based on the vlan features of the lower-level
device.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason reported an oops caused by SCTP on his ARM machine with
SCTP authentication enabled:
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 104 Comm: sctp-test Not tainted 3.13.0-68744-g3632f30c9b20-dirty #1
task: c6eefa40 ti: c6f52000 task.ti: c6f52000
PC is at sctp_auth_calculate_hmac+0xc4/0x10c
LR is at sg_init_table+0x20/0x38
pc : [<c024bb80>] lr : [<c00f32dc>] psr: 40000013
sp : c6f538e8 ip : 00000000 fp : c6f53924
r10: c6f50d80 r9 : 00000000 r8 : 00010000
r7 : 00000000 r6 : c7be4000 r5 : 00000000 r4 : c6f56254
r3 : c00c8170 r2 : 00000001 r1 : 00000008 r0 : c6f1e660
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005397f Table: 06f28000 DAC: 00000015
Process sctp-test (pid: 104, stack limit = 0xc6f521c0)
Stack: (0xc6f538e8 to 0xc6f54000)
[...]
Backtrace:
[<c024babc>] (sctp_auth_calculate_hmac+0x0/0x10c) from [<c0249af8>] (sctp_packet_transmit+0x33c/0x5c8)
[<c02497bc>] (sctp_packet_transmit+0x0/0x5c8) from [<c023e96c>] (sctp_outq_flush+0x7fc/0x844)
[<c023e170>] (sctp_outq_flush+0x0/0x844) from [<c023ef78>] (sctp_outq_uncork+0x24/0x28)
[<c023ef54>] (sctp_outq_uncork+0x0/0x28) from [<c0234364>] (sctp_side_effects+0x1134/0x1220)
[<c0233230>] (sctp_side_effects+0x0/0x1220) from [<c02330b0>] (sctp_do_sm+0xac/0xd4)
[<c0233004>] (sctp_do_sm+0x0/0xd4) from [<c023675c>] (sctp_assoc_bh_rcv+0x118/0x160)
[<c0236644>] (sctp_assoc_bh_rcv+0x0/0x160) from [<c023d5bc>] (sctp_inq_push+0x6c/0x74)
[<c023d550>] (sctp_inq_push+0x0/0x74) from [<c024a6b0>] (sctp_rcv+0x7d8/0x888)
While we already had various kind of bugs in that area ec0223ec48a9 ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if
we/peer is AUTH capable") and b14878ccb7fa ("net: sctp: cache
auth_enable per endpoint"), this one is a bit of a different
kind.
Giving a bit more background on why SCTP authentication is
needed can be found in RFC4895:
SCTP uses 32-bit verification tags to protect itself against
blind attackers. These values are not changed during the
lifetime of an SCTP association.
Looking at new SCTP extensions, there is the need to have a
method of proving that an SCTP chunk(s) was really sent by
the original peer that started the association and not by a
malicious attacker.
To cause this bug, we're triggering an INIT collision between
peers; normal SCTP handshake where both sides intent to
authenticate packets contains RANDOM; CHUNKS; HMAC-ALGO
parameters that are being negotiated among peers:
RFC4895 says that each endpoint therefore knows its own random
number and the peer's random number *after* the association
has been established. The local and peer's random number along
with the shared key are then part of the secret used for
calculating the HMAC in the AUTH chunk.
Now, in our scenario, we have 2 threads with 1 non-blocking
SEQ_PACKET socket each, setting up common shared SCTP_AUTH_KEY
and SCTP_AUTH_ACTIVE_KEY properly, and each of them calling
sctp_bindx(3), listen(2) and connect(2) against each other,
thus the handshake looks similar to this, e.g.:
Since such collisions can also happen with verification tags,
the RFC4895 for AUTH rather vaguely says under section 6.1:
In case of INIT collision, the rules governing the handling
of this Random Number follow the same pattern as those for
the Verification Tag, as explained in Section 5.2.4 of
RFC 2960 [5]. Therefore, each endpoint knows its own Random
Number and the peer's Random Number after the association
has been established.
In RFC2960, section 5.2.4, we're eventually hitting Action B:
B) In this case, both sides may be attempting to start an
association at about the same time but the peer endpoint
started its INIT after responding to the local endpoint's
INIT. Thus it may have picked a new Verification Tag not
being aware of the previous Tag it had sent this endpoint.
The endpoint should stay in or enter the ESTABLISHED
state but it MUST update its peer's Verification Tag from
the State Cookie, stop any init or cookie timers that may
running and send a COOKIE ACK.
In other words, the handling of the Random parameter is the
same as behavior for the Verification Tag as described in
Action B of section 5.2.4.
Looking at the code, we exactly hit the sctp_sf_do_dupcook_b()
case which triggers an SCTP_CMD_UPDATE_ASSOC command to the
side effect interpreter, and in fact it properly copies over
peer_{random, hmacs, chunks} parameters from the newly created
association to update the existing one.
Also, the old asoc_shared_key is being released and based on
the new params, sctp_auth_asoc_init_active_key() updated.
However, the issue observed in this case is that the previous
asoc->peer.auth_capable was 0, and has *not* been updated, so
that instead of creating a new secret, we're doing an early
return from the function sctp_auth_asoc_init_active_key()
leaving asoc->asoc_shared_key as NULL. However, we now have to
authenticate chunks from the updated chunk list (e.g. COOKIE-ACK).
That in fact causes the server side when responding with ...
... to trigger a NULL pointer dereference, since in
sctp_packet_transmit(), it discovers that an AUTH chunk is
being queued for xmit, and thus it calls sctp_auth_calculate_hmac().
Since the asoc->active_key_id is still inherited from the
endpoint, and the same as encoded into the chunk, it uses
asoc->asoc_shared_key, which is still NULL, as an asoc_key
and dereferences it in ...
... causing an oops. All this happens because sctp_make_cookie_ack()
called with the *new* association has the peer.auth_capable=1
and therefore marks the chunk with auth=1 after checking
sctp_auth_send_cid(), but it is *actually* sent later on over
the then *updated* association's transport that didn't initialize
its shared key due to peer.auth_capable=0. Since control chunks
in that case are not sent by the temporary association which
are scheduled for deletion, they are issued for xmit via
SCTP_CMD_REPLY in the interpreter with the context of the
*updated* association. peer.auth_capable was 0 in the updated
association (which went from COOKIE_WAIT into ESTABLISHED state),
since all previous processing that performed sctp_process_init()
was being done on temporary associations, that we eventually
throw away each time.
The correct fix is to update to the new peer.auth_capable
value as well in the collision case via sctp_assoc_update(),
so that in case the collision migrated from 0 -> 1,
sctp_auth_asoc_init_active_key() can properly recalculate
the secret. This therefore fixes the observed server panic.
Fixes: 730fc3d05cd4 ("[SCTP]: Implete SCTP-AUTH parameter processing") Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In vegas we do a multiplication of the cwnd and the rtt. This
may overflow and thus their result is stored in a u64. However, we first
need to cast the cwnd so that actually 64-bit arithmetic is done.
Then, we need to do do_div to allow this to be used on 32-bit arches.
Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Doug Leith <doug.leith@nuim.ie> Fixes: 8d3a564da34e (tcp: tcp_vegas cong avoid fix) Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In veno we do a multiplication of the cwnd and the rtt. This
may overflow and thus their result is stored in a u64. However, we first
need to cast the cwnd so that actually 64-bit arithmetic is done.
A first attempt at fixing 76f1017757aa0 ([TCP]: TCP Veno congestion
control) was made by 159131149c2 (tcp: Overflow bug in Vegas), but it
failed to add the required cast in tcp_veno_cong_avoid().
Fixes: 76f1017757aa0 ([TCP]: TCP Veno congestion control) Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This reports means that we've come to netlink_sendmsg() with msg->msg_name == NULL and msg->msg_namelen > 0.
After this report there was no usual "Unable to handle kernel NULL pointer dereference"
and this gave me a clue that address 0 is mapped and contains valid socket address structure in it.
This bug was introduced in f3d3342602f8bcbf37d7c46641cb9bca7618eb1c
(net: rework recvmsg handler msg_name and msg_namelen logic).
Commit message states that:
"Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address."
But in fact this affects sendto when address 0 is mapped and contains
socket address structure in it. In such case copy-in address will succeed,
verify_iovec() function will successfully exit with msg->msg_namelen > 0
and msg->msg_name == NULL.
This patch fixes it by setting msg_namelen to 0 if msg_name == NULL.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Eric Dumazet <edumazet@google.com> Cc: <stable@vger.kernel.org> Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and
Jedidiah describe ways exploiting linux IP identifier generation to
infer whether two machines are exchanging packets.
With commit 73f156a6e8c1 ("inetpeer: get rid of ip_id_count"), we
changed IP id generation, but this does not really prevent this
side-channel technique.
This patch adds a random amount of perturbation so that IP identifiers
for a given destination [1] are no longer monotonically increasing after
an idle period.
Note that prandom_u32_max(1) returns 0, so if generator is used at most
once per jiffy, this patch inserts no hole in the ID suite and do not
increase collision probability.
This is jiffies based, so in the worst case (HZ=1000), the id can
rollover after ~65 seconds of idle time, which should be fine.
We also change the hash used in __ip_select_ident() to not only hash
on daddr, but also saddr and protocol, so that ICMP probes can not be
used to infer information for other protocols.
For IPv6, adds saddr into the hash as well, but not nexthdr.
If I ping the patched target, we can see ID are now hard to predict.
21:57:11.008086 IP (...)
A > target: ICMP echo request, seq 1, length 64
21:57:11.010752 IP (... id 2081 ...)
target > A: ICMP echo reply, seq 1, length 64
21:57:12.013133 IP (...)
A > target: ICMP echo request, seq 2, length 64
21:57:12.015737 IP (... id 3039 ...)
target > A: ICMP echo reply, seq 2, length 64
21:57:13.016580 IP (...)
A > target: ICMP echo request, seq 3, length 64
21:57:13.019251 IP (... id 3437 ...)
target > A: ICMP echo reply, seq 3, length 64
[1] TCP sessions uses a per flow ID generator not changed by this patch.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu> Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Hannes Frederic Sowa <hannes@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: a848ade408b ("bnx2x: add CSUM and TSO support for encapsulation protocols") Reported-by: Yulong Pei <ypei@redhat.com> Cc: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
init_espfix_ap() is currently off by one level when informing hypervisor
that allocated pages will be used for ministacks' page tables.
The most immediate effect of this on a PV guest is that if
'stack_page = __get_free_page()' returns a non-zeroed-out page the hypervisor
will refuse to use it for a page table (which it shouldn't be anyway). This will
result in warnings by both Xen and Linux.
More importantly, a subsequent write to that page (again, by a PV guest) is
likely to result in fatal page fault.
The l2tp [get|set]sockopt() code has fallen back to the UDP functions
for socket option levels != SOL_PPPOL2TP since day one, but that has
never actually worked, since the l2tp socket isn't an inet socket.
As David Miller points out:
"If we wanted this to work, it'd have to look up the tunnel and then
use tunnel->sk, but I wonder how useful that would be"
Since this can never have worked so nobody could possibly have depended
on that functionality, just remove the broken code and return -EINVAL.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: James Chapman <jchapman@katalix.com> Acked-by: David Miller <davem@davemloft.net> Cc: Phil Turnbull <phil.turnbull@oracle.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There are two FIXMEs in the double exception handler 'for the extremely
unlikely case'. This case gets hit by gcc during kernel build once in
a few hours, resulting in an unrecoverable exception condition.
Provide missing fixup routine to handle this case. Double exception
literals now need 8 more bytes, add them to the linker script.
Also replace bbsi instructions with bbsi.l as we're branching depending
on 8th and 7th LSB-based bits of exception address.
This may be tested by adding the explicit DTLB invalidation to window
overflow handlers, like the following:
This reverts commit 277d916fc2e959c3f106904116bb4f7b1148d47a as it was
at least breaking iwlwifi by setting the IEEE80211_TX_CTL_NO_PS_BUFFER
flag in all kinds of interface modes, not only for AP mode where it is
appropriate.
To avoid reintroducing the original problem, explicitly check for probe
request frames in the multicast buffering code.
Fixes: 277d916fc2e9 ("mac80211: move "bufferable MMPDU" check to fix AP mode scan") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This moves the espfix64 logic into native_iret. To make this work,
it gets rid of the native patch for INTERRUPT_RETURN:
INTERRUPT_RETURN on native kernels is now 'jmp native_iret'.
This changes the 16-bit SS behavior on Xen from OOPSing to leaking
some bits of the Xen hypervisor's RSP (I think).
[ hpa: this is a nonzero cost on native, but probably not enough to
measure. Xen needs to fix this in their own code, probably doing
something equivalent to espfix64. ]
Embedded systems, which may be very memory-size-sensitive, are
extremely unlikely to ever encounter any 16-bit software, so make it
a CONFIG_EXPERT option to turn off support for any 16-bit software
whatsoever.
Make espfix64 a hidden Kconfig option. This fixes the x86-64 UML
build which had broken due to the non-existence of init_espfix_bsp()
in UML: since UML uses its own Kconfig, this option does not appear in
the UML build.
This also makes it possible to make support for 16-bit segments a
configuration option, for the people who want to minimize the size of
the kernel.
Sparse warns that the percpu variables aren't declared before they are
defined. Rather than hacking around it, move espfix definitions into
a proper header file.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer. This
causes some 16-bit software to break, but it also leaks kernel state
to user space. We have a software workaround for that ("espfix") for
the 32-bit kernel, but it relies on a nonzero stack segment base which
is not available in 64-bit mode.
In checkin:
b3b42ac2cbae x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
we "solved" this by forbidding 16-bit segments on 64-bit kernels, with
the logic that 16-bit support is crippled on 64-bit kernels anyway (no
V86 support), but it turns out that people are doing stuff like
running old Win16 binaries under Wine and expect it to work.
This works around this by creating percpu "ministacks", each of which
is mapped 2^16 times 64K apart. When we detect that the return SS is
on the LDT, we copy the IRET frame to the ministack and use the
relevant alias to return to userspace. The ministacks are mapped
readonly, so if IRET faults we promote #GP to #DF which is an IST
vector and thus has its own stack; we then do the fixup in the #DF
handler.
(Making #GP an IST exception would make the msr_safe functions unsafe
in NMI/MC context, and quite possibly have other effects.)
Special thanks to:
- Andy Lutomirski, for the suggestion of using very small stack slots
and copy (as opposed to map) the IRET frame there, and for the
suggestion to mark them readonly and let the fault promote to #DF.
- Konrad Wilk for paravirt fixup and testing.
- Borislav Petkov for testing help and useful comments.
Reported-by: Brian Gerst <brgerst@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Link: http://lkml.kernel.org/r/1398816946-3351-1-git-send-email-hpa@linux.intel.com Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Andrew Lutomriski <amluto@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Dirk Hohndel <dirk@hohndel.org> Cc: Arjan van de Ven <arjan.van.de.ven@intel.com> Cc: comex <comexk@gmail.com> Cc: Alexander van Heukelum <heukelum@fastmail.fm> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: <stable@vger.kernel.org> # consider after upstream merge Signed-off-by: Jiri Slaby <jslaby@suse.cz>
clockevents_increase_min_delta() calls printk() from under
hrtimer_bases.lock. That causes lock inversion on scheduler locks because
printk() can call into the scheduler. Lockdep puts it as:
======================================================
[ INFO: possible circular locking dependency detected ] 3.15.0-rc8-06195-g939f04b #2 Not tainted
-------------------------------------------------------
trinity-main/74 is trying to acquire lock:
(&port_lock_key){-.....}, at: [<811c60be>] serial8250_console_write+0x8c/0x10c
but task is already holding lock:
(hrtimer_bases.lock){-.-...}, at: [<8103caeb>] hrtimer_try_to_cancel+0x13/0x66
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
After learning we'll need some sort of deferred printk functionality in
the timekeeping core, Peter suggested we rename the printk_sched function
so it can be reused by needed subsystems.
This only changes the function name. No logic changes.
Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: Jan Kara <jack@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Bohac <jbohac@suse.cz> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
nr_dirty is updated without locking, causing it to drift so that it is
non-zero (either a small positive integer, or a very large one when an
underflow occurs) even when there are no actual dirty blocks. This was
due to a race between the workqueue and map function accessing nr_dirty
in parallel without proper protection.
People were seeing under runs due to a race on increment/decrement of
nr_dirty, see: https://lkml.org/lkml/2014/6/3/648
Fix this by using an atomic_t for nr_dirty.
Reported-by: roma1390@gmail.com Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
1d3d4437eae1 ("vmscan: per-node deferred work") added a flags field to
struct shrinker assuming that all shrinkers were zero filled. The dm
bufio shrinker is not zero filled, which leaves arbitrary kmalloc() data
in flags. So far the only defined flags bit is SHRINKER_NUMA_AWARE.
But there are proposed patches which add other bits to shrinker.flags
(e.g. memcg awareness).
Rather than simply initializing the shrinker, this patch uses kzalloc()
when allocating the dm_bufio_client to ensure that the embedded shrinker
and any other similar structures are zeroed.
This fixes theoretical over aggressive shrinking of dm bufio objects.
If the uninitialized dm_bufio_client.shrinker.flags contains
SHRINKER_NUMA_AWARE then shrink_slab() would call the dm shrinker for
each numa node rather than just once. This has been broken since 3.12.
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.
Commit fb2a6fc56be6 ("mm: memcg: rework and document OOM waiting and
wakeup") has moved mem_cgroup_oom_notify outside of memcg_oom_lock
assuming it is protected by the hierarchical OOM-lock.
Although this is true for the notification part the protection doesn't
cover unregistration of event which can happen in parallel now so
mem_cgroup_oom_notify can see already unlinked and/or freed
mem_cgroup_eventfd_list.
Fix this by using memcg_oom_lock also in mem_cgroup_oom_notify.
The page allocator relies on __GFP_WAIT to determine if ALLOC_CPUSET
should be set in allocflags. ALLOC_CPUSET controls if a page allocation
should be restricted only to the set of allowed cpuset mems.
Transparent hugepages clears __GFP_WAIT when defrag is disabled to prevent
the fault path from using memory compaction or direct reclaim. Thus, it
is unfairly able to allocate outside of its cpuset mems restriction as a
side-effect.
This patch ensures that ALLOC_CPUSET is only cleared when the gfp mask is
truly GFP_ATOMIC by verifying it is also not a thp allocation.
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Alex Thorlton <athorlton@sgi.com> Tested-by: Alex Thorlton <athorlton@sgi.com> Cc: Bob Liu <lliubbo@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Hedi Berriche <hedi@sgi.com> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Under memory pressure, it is possible for dirty_thresh, calculated by
global_dirty_limits() in balance_dirty_pages(), to equal zero. Then, if
strictlimit is true, bdi_dirty_limits() tries to resolve the proportion:
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com> Reported-by: Steven Haber <steven@qumulo.com> Tested-by: Steven Haber <steven@qumulo.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This is a bug fix for the situation when function tsi721_desc_get() fails
to obtain a free transaction descriptor.
The bug usually results in a memory access crash dump when data transfer
scatter-gather list has more entries than size of hardware buffer
descriptors ring. This fix ensures that error is properly returned to a
caller instead of an invalid entry.
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Stef van Os <stef.van.os@prodrive-technologies.com> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Reported-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / linux-stable / log