Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Nandita Dukkipati <nanditad@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently association restarts do not take into consideration the
state of the socket. When a restart happens, the current assocation
simply transitions into established state. This creates a condition
where a remote system, through a the restart procedure, may create a
local association that is no way reachable by user. The conditions
to trigger this are as follows:
1) Remote does not acknoledge some data causing data to remain
outstanding.
2) Local application calls close() on the socket. Since data
is still outstanding, the association is placed in SHUTDOWN_PENDING
state. However, the socket is closed.
3) The remote tries to create a new association, triggering a restart
on the local system. The association moves from SHUTDOWN_PENDING
to ESTABLISHED. At this point, it is no longer reachable by
any socket on the local system.
This patch addresses the above situation by moving the newly ESTABLISHED
association into SHUTDOWN-SENT state and bundling a SHUTDOWN after
the COOKIE-ACK chunk. This way, the restarted associate immidiately
enters the shutdown procedure and forces the termination of the
unreachable association.
Reported-by: David Laight <David.Laight@aculab.com> Signed-off-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Fixes: fc423ff00df3a19554414ee ("team: add peer notification") Fixes: 492b200efdd20b8fcfdac87 ("team: add support for sending multicast rejoins") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Long Li <longli@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver. Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In macvtap device delete and open calls can race and
this causes a list curruption of the vlan queue_list.
The race intself is triggered by the idr accessors
that located the vlan device. The device is stored
into and removed from the idr under both an rtnl and
a mutex. However, when attempting to locate the device
in idr, only a mutex is taken. As a result, once cpu
perfoming a delete may take an rtnl and wait for the mutex,
while another cput doing an open() will take the idr
mutex first to fetch the device pointer and later take
an rtnl to add a queue for the device which may have
just gotten deleted.
With this patch, we now hold the rtnl for the duration
of the macvtap_open() call thus making sure that
open will not race with delete.
CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently we genarate a queueing route if we have matching policies
but can not resolve the states and the sysctl xfrm_larval_drop is
disabled. Here we assume that dst_output() is called to kill the
queued packets. Unfortunately this assumption is not true in all
cases, so it is possible that these packets leave the system unwanted.
We fix this by generating queueing routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com> CC: Prashant Sreedharan <prashant@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will
not be initialized in br_should_learn() as that function
is called only from br_handle_local_finish(). That is
an input handler for link-local ethernet traffic so it perfectly
correct to check br->vlan_enabled here.
Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com> Fixes: 20adfa1 bridge: Check if vlan filtering is enabled only once. Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The bridge code checks if vlan filtering is enabled on both
ingress and egress. When the state flip happens, it
is possible for the bridge to currently be forwarding packets
and forwarding behavior becomes non-deterministic. Bridge
may drop packets on some interfaces, but not others.
This patch solves this by caching the filtered state of the
packet into skb_cb on ingress. The skb_cb is guaranteed to
not be over-written between the time packet entres bridge
forwarding path and the time it leaves it. On egress, we
can then check the cached state to see if we need to
apply filtering information.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Use dst_entry held by sk_dst_get() to retrieve tunnel's PMTU.
The dst_mtu(__sk_dst_get(tunnel->sock)) call was racy. __sk_dst_get()
could return NULL if tunnel->sock->sk_dst_cache was reset just before the
call, thus making dst_mtu() dereference a NULL pointer:
Fixes: f34c4a35d879 ("l2tp: take PMTU from tunnel UDP socket") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
is optimised away by the compiler, due to the second initializer,
therefore initialising .sin.sin_addr.s_addr always to 0.
This results in netlink messages indicating a L3 miss never contain the
missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions.
The problem affects user space programs relying on an IP address being
sent as part of a netlink message indicating a L3 miss.
Changing
.sa.sa_family = AF_INET,
to
.sin.sin_family = AF_INET,
fixes the problem.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.") Acked-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix TCP FRTO logic so that it always notices when snd_una advances,
indicating that any RTO after that point will be a new and distinct
loss episode.
Previously there was a very specific sequence that could cause FRTO to
fail to notice a new loss episode had started:
(1) RTO timer fires, enter FRTO and retransmit packet 1 in write queue
(2) receiver ACKs packet 1
(3) FRTO sends 2 more packets
(4) RTO timer fires again (should start a new loss episode)
The problem was in step (3) above, where tcp_process_loss() returned
early (in the spot marked "Step 2.b"), so that it never got to the
logic to clear icsk_retransmits. Thus icsk_retransmits stayed
non-zero. Thus in step (4) tcp_enter_loss() would see the non-zero
icsk_retransmits, decide that this RTO is not a new episode, and
decide not to cut ssthresh and remember the current cwnd and ssthresh
for undo.
There were two main consequences to the bug that we have
observed. First, ssthresh was not decreased in step (4). Second, when
there was a series of such FRTO (1-4) sequences that happened to be
followed by an FRTO undo, we would restore the cwnd and ssthresh from
before the entire series started (instead of the cwnd and ssthresh
from before the most recent RTO). This could result in cwnd and
ssthresh being restored to values much bigger than the proper values.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Fixes: e33099f96d99c ("tcp: implement RFC5682 F-RTO") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().
Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Diagnosed-by: Willem de Bruijn <willemb@google.com> Fixes: 563d34d057862 ("tcp: dont drop MTU reduction indications") Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
As of 4fddbf5d78 ("sit: strictly restrict incoming traffic to tunnel link device"),
when looking up a tunnel, tunnel's underlying interface (t->parms.link)
is verified to match incoming traffic's ingress device.
However the comparison was incorrectly based on skb->dev->iflink.
Instead, dev->ifindex should be used, which correctly represents the
interface from which the IP stack hands the ipip6 packets.
This allows setting up sit tunnels bound to vlan interfaces (otherwise
incoming ipip6 traffic on the vlan interface was dropped due to
ipip6_tunnel_lookup match failure).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val 4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val 4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net> CC: Nithin Nayak Sujir <nsujir@broadcom.com> CC: Michael Chan <mchan@broadcom.com> CC: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 1d8faf48c74b8 ("net/core: Add VF link state control") added new
attribute to IFLA_VF_INFO group in rtnl_fill_ifinfo but did not adjust size
of the allocated memory in if_nlmsg_size/rtnl_vfinfo_size. As the result, we
may trigger warnings in rtnl_getlink and similar functions when many VF
links are enabled, as the information does not fit into the allocated skb.
Fixes: 1d8faf48c74b8 ("net/core: Add VF link state control") Reported-by: Yulong Pei <ypei@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
netlink doesn't set any network header offset thus when the skb is
being passed to tap devices via dev_queue_xmit_nit(), it emits klog
false positives due to it being unset like:
...
[ 124.990397] protocol 0000 is buggy, dev nlmon0
[ 124.990411] protocol 0000 is buggy, dev nlmon0
...
So just reset the network header before passing to the device; for
packet sockets that just means nothing will change - mac and net
offset hold the same value just as before.
Reported-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.
Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Cc: Neil Brown <nfbrown@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since linux kernel 3.13, kthread_run() internally uses
wait_for_completion_killable(). We sometimes may use kthread_run()
while we still have a signal pending, which we used to kick our threads
out of potentially blocking network functions, causing kthread_run() to
mistake that as a new fatal signal and fail.
Fix: flush_signals() before kthread_run().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
timeval_to_jiffies tried to round a timeval up to an integral number
of jiffies, but the logic for doing so was incorrect: intervals
corresponding to exactly N jiffies would become N+1. This manifested
itself particularly repeatedly stopping/starting an itimer:
would add a full tick to val, _even if it was exactly representable in
terms of jiffies_ (say, the result of a previous rounding.) Doing
this repeatedly would cause unbounded growth in val. So fix the math.
Here's what was wrong with the conversion: we essentially computed
(eliding seconds)
jiffies = usec * (NSEC_PER_USEC/TICK_NSEC)
by using scaling arithmetic, which took the best approximation of
NSEC_PER_USEC/TICK_NSEC with denominator of 2^USEC_JIFFIE_SC =
x/(2^USEC_JIFFIE_SC), and computed:
jiffies = (usec * x) >> USEC_JIFFIE_SC
and rounded this calculation up in the intermediate form (since we
can't necessarily exactly represent TICK_NSEC in usec.) But the
scaling arithmetic is a (very slight) *over*approximation of the true
value; that is, instead of dividing by (1 usec/ 1 jiffie), we
effectively divided by (1 usec/1 jiffie)-epsilon (rounding
down). This would normally be fine, but we want to round timeouts up,
and we did so by adding 2^USEC_JIFFIE_SC - 1 before the shift; this
would be fine if our division was exact, but dividing this by the
slightly smaller factor was equivalent to adding just _over_ 1 to the
final result (instead of just _under_ 1, as desired.)
In particular, with HZ=1000, we consistently computed that 10000 usec
was 11 jiffies; the same was true for any exact multiple of
TICK_NSEC.
We could possibly still round in the intermediate form, adding
something less than 2^USEC_JIFFIE_SC - 1, but easier still is to
convert usec->nsec, round in nanoseconds, and then convert using
time*spec*_to_jiffies. This adds one constant multiplication, and is
not observably slower in microbenchmarks on recent x86 hardware.
Tested: the following program:
int main() {
struct itimerval zero = {{0, 0}, {0, 0}};
/* Initially set to 10 ms. */
struct itimerval initial = zero;
initial.it_interval.tv_usec = 10000;
setitimer(ITIMER_PROF, &initial, NULL);
/* Save and restore several times. */
for (size_t i = 0; i < 10; ++i) {
struct itimerval prev;
setitimer(ITIMER_PROF, &zero, &prev);
/* on old kernels, this goes up by TICK_USEC every iteration */
printf("previous value: %ld %ld %ld %ld\n",
prev.it_interval.tv_sec, prev.it_interval.tv_usec,
prev.it_value.tv_sec, prev.it_value.tv_usec);
setitimer(ITIMER_PROF, &prev, NULL);
}
return 0;
}
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul Turner <pjt@google.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Reviewed-by: Paul Turner <pjt@google.com> Reported-by: Aaron Jacobs <jacobsa@google.com> Signed-off-by: Andrew Hunter <ahh@google.com>
[jstultz: Tweaked to apply to 3.17-rc] Signed-off-by: John Stultz <john.stultz@linaro.org>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
This patch reverts 1ba6e0b50b ("mm: numa: split_huge_page: transfer the
NUMA type from the pmd to the pte"). If a huge page is being split due
a protection change and the tail will be in a PROT_NONE vma then NUMA
hinting PTEs are temporarily created in the protected VMA.
VM_RW|VM_PROTNONE
|-----------------|
^
split here
In the specific case above, it should get fixed up by change_pte_range()
but there is a window of opportunity for weirdness to happen. Similarly,
if a huge page is shrunk and split during a protection update but before
pmd_numa is cleared then a pte_numa can be left behind.
Instead of adding complexity trying to deal with the case, this patch
will not mark PTEs NUMA when splitting a huge page. NUMA hinting faults
will not be triggered which is marginal in comparison to the complexity
in dealing with the corner cases during THP split.
In __split_huge_page_map(), the check for page_mapcount(page) is
invariant within the for loop. Because of the fact that the macro is
implemented using atomic_read(), the redundant check cannot be optimized
away by the compiler leading to unnecessary read to the page structure.
This patch moves the invariant bug check out of the loop so that it will
be done only once. On a 3.16-rc1 based kernel, the execution time of a
microbenchmark that broke up 1000 transparent huge pages using munmap()
had an execution time of 38,245us and 38,548us with and without the
patch respectively. The performance gain is about 1%.
Signed-off-by: Waiman Long <Waiman.Long@hp.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Scott J Norton <scott.norton@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
SMB2 servers indicates the end of a directory search with
STATUS_NO_MORE_FILE error code that is not processed now.
This causes generic/257 xfstest to fail. Fix this by triggering
the end of search by this error code in SMB2_query_directory.
Also when negotiating CIFS protocol we tell the server to close
the search automatically at the end and there is no need to do
it itself. In the case of SMB2 protocol, we need to close it
explicitly - separate close directory checks for different
protocols.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 651e22f2701b "ring-buffer: Always reset iterator to reader page"
fixed one bug but in the process caused another one. The reset is to
update the header page, but that fix also changed the way the cached
reads were updated. The cache reads are used to test if an iterator
needs to be updated or not.
A ring buffer iterator, when created, disables writes to the ring buffer
but does not stop other readers or consuming reads from happening.
Although all readers are synchronized via a lock, they are only
synchronized when in the ring buffer functions. Those functions may
be called by any number of readers. The iterator continues down when
its not interrupted by a consuming reader. If a consuming read
occurs, the iterator starts from the beginning of the buffer.
The way the iterator sees that a consuming read has happened since
its last read is by checking the reader "cache". The cache holds the
last counts of the read and the reader page itself.
Commit 651e22f2701b changed what was saved by the cache_read when
the rb_iter_reset() occurred, making the iterator never match the cache.
Then if the iterator calls rb_iter_reset(), it will go into an
infinite loop by checking if the cache doesn't match, doing the reset
and retrying, just to see that the cache still doesn't match! Which
should never happen as the reset is suppose to set the cache to the
current value and there's locks that keep a consuming reader from
having access to the data.
Fixes: 651e22f2701b "ring-buffer: Always reset iterator to reader page" Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit 03b8c7b623c80af264c4c8d6111e5c6289933666 ("futex: Allow
architectures to skip futex_atomic_cmpxchg_inatomic() test") added the
HAVE_FUTEX_CMPXCHG symbol right below FUTEX. This placed it right in
the middle of the options for the EXPERT menu. However,
HAVE_FUTEX_CMPXCHG does not depend on EXPERT or FUTEX, so Kconfig stops
placing items in the EXPERT menu, and displays the remaining several
EXPERT items (starting with EPOLL) directly in the General Setup menu.
Since both users of HAVE_FUTEX_CMPXCHG only select it "if FUTEX", make
HAVE_FUTEX_CMPXCHG itself depend on FUTEX. With this change, the
subsequent items display as part of the EXPERT menu again; the EMBEDDED
menu now appears as the next top-level item in the General Setup menu,
which makes General Setup much shorter and more usable.
As we use WC updates of the PTE, we are responsible for notifying the
hardware when to flush its TLBs. Do so after we zap all the PTEs before
suspend (and the BIOS tries to read our GTT).
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <shli@kernel.org> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Heinz Mauelshagen <heinzm@redhat.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Fixes: 620125f2bf8ff0c4969b79653b54d7bcc9d40637 Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A migration entry is marked as write if pte_write was true at the time the
entry was created. The VMA protections are not double checked when migration
entries are being removed as mprotect marks write-migration-entries as
read. It means that potentially we take a spurious fault to mark PTEs write
again but it's straight-forward. However, there is a race between write
migrations being marked read and migrations finishing. This potentially
allows a PTE to be write that should have been read. Close this race by
double checking the VMA permissions using maybe_mkwrite when migration
completes.
[torvalds@linux-foundation.org: use maybe_mkwrite] Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Oleg noticed that a cleanup by Sylvain actually uncovered a bug; by
calling perf_event_free_task() when failing sched_fork() we will not yet
have done the memset() on ->perf_event_ctxp[] and will therefore try and
'free' the inherited contexts, which are still in use by the parent
process. This is bad..
We did not implement any bound on number of indirect ICBs we follow when
loading inode. Thus corrupted medium could cause kernel to go into an
infinite loop, possibly causing a stack overflow.
Fix the possible stack overflow by removing recursion from
__udf_read_inode() and limit number of indirect ICBs we follow to avoid
infinite loops.
Signed-off-by: Jan Kara <jack@suse.cz> Cc: Chuck Ebbert <cebbert.lkml@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The lustre virtual block device cannot handle 64K pages and fails at compile
time. To avoid running into this error, let's disable the Kconfig option
for this driver in cases it doesn't support.
It seems that exit_aio() also needs to wait for all iocbs to complete (like
io_destroy), but we missed the wait step in current implemention, so fix
it in the same way as we did in io_destroy.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In some cases, clocks can switch their parent with clk_set_rate, for
example clk_mux can do this in some cases. Current implementation of
clk_change_rate uses un-safe list iteration on the clock children, which
will cause wrong clocks to be parsed in case any of the clock children
change their parents during the change rate operation. Fixed by using
the safe list iterator instead.
The problem was detected due to some divide by zero errors generated
by clock init on dra7-evm board, see discussion under
http://article.gmane.org/gmane.linux.ports.arm.kernel/349180 for details.
Fixes: 71472c0c06cf ("clk: add support for clock reparent on set_rate") Signed-off-by: Tero Kristo <t-kristo@ti.com> Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Accordingly to discussion [1] and followed up documentation the DMA controller
driver shouldn't start any DMA operations when dmaengine_submit() is called.
This patch fixes the workflow in dw_dmac driver to follow the documentation.
Use the observation that, for platform-dependent sleep states
(PM_SUSPEND_STANDBY, PM_SUSPEND_MEM), a given state is either
always supported or always unsupported and store that information
in pm_states[] instead of calling valid_state() every time we
need to check it.
Also do not use valid_state() for PM_SUSPEND_FREEZE, which is always
valid, and move the pm_test_level validity check for PM_SUSPEND_FREEZE
directly into enter_state().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
To allow sleep states corresponding to the "mem", "standby" and
"freeze" lables to be different from the pm_states[] indexes of
those strings, introduce struct pm_sleep_state, consisting of
a string label and a state number, and turn pm_states[] into an
array of objects of that type.
This modification should not lead to any functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747c0dbf49506ec906757a6b87b9741e9 Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com> Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In testmode and vendor command reply/event SKBs we use the
skb cb data to store nl80211 parameters between allocation
and sending. This causes the code for CONFIG_NETLINK_MMAP
to get confused, because it takes ownership of the skb cb
data when the SKB is handed off to netlink, and it doesn't
explicitly clear it.
Clear the skb cb explicitly when we're done and before it
gets passed to netlink to avoid this issue.
Reported-by: Assaf Azulay <assaf.azulay@intel.com> Reported-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On 32-bit architectures, the legacy buffer_head functions are not always
handling the sector number with the proper 64-bit types, and will thus
fail on 4TB+ disks.
Any code that uses __getblk() (and thus bread(), breadahead(),
sb_bread(), sb_breadahead(), sb_getblk()), and calls it using a 64-bit
block on a 32-bit arch (where "long" is 32-bit) causes an inifinite loop
in __getblk_slow() with an infinite stream of errors logged to dmesg
like this:
Note how in hex block is 0x191C1F988 and b_blocknr is 0x91C1F988 i.e. the
top 32-bits are missing (in this case the 0x1 at the top).
This is because grow_dev_page() is broken and has a 32-bit overflow due
to shifting the page index value (a pgoff_t - which is just 32 bits on
32-bit architectures) left-shifted as the block number. But the top
bits to get lost as the pgoff_t is not type cast to sector_t / 64-bit
before the shift.
This patch fixes this issue by type casting "index" to sector_t before
doing the left shift.
Note this is not a theoretical bug but has been seen in the field on a
4TiB hard drive with logical sector size 512 bytes.
This patch has been verified to fix the infinite loop problem on 3.17-rc5
kernel using a 4TB disk image mounted using "-o loop". Without this patch
doing a "find /nt" where /nt is an NTFS volume causes the inifinite loop
100% reproducibly whilst with the patch it works fine as expected.
We saw a kernel soft lockup in perf_remove_from_context(),
it looks like the `perf` process, when exiting, could not go
out of the retry loop. Meanwhile, the target process was forking
a child. So either the target process should execute the smp
function call to deactive the event (if it was running) or it should
do a context switch which deactives the event.
It seems we optimize out a context switch in perf_event_context_sched_out(),
and what's more important, we still test an obsolete task pointer when
retrying, so no one actually would deactive that event in this situation.
Fix it directly by reloading the task pointer in perf_remove_from_context().
This should cure the above soft lockup.
Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1409696840-843-1-git-send-email-xiyou.wangcong@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This particular reference count is not needed with the rcu protection,
and the current code leaks a reference count, causing a hang in
qib_qp_destroy().
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Locks the k_itimer's it_lock member when handling the alarm timer's
expiry callback.
The regular posix timers defined in posix-timers.c have this lock held
during timout processing because their callbacks are routed through
posix_timer_fn(). The alarm timers follow a different path, so they
ought to grab the lock somewhere else.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by: Richard Larocque <rlarocque@google.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Avoids sending a signal to alarm timers created with sigev_notify set to
SIGEV_NONE by checking for that special case in the timeout callback.
The regular posix timers avoid sending signals to SIGEV_NONE timers by
not scheduling any callbacks for them in the first place. Although it
would be possible to do something similar for alarm timers, it's simpler
to handle this as a special case in the timeout.
Prior to this patch, the alarm timer would ignore the sigev_notify value
and try to deliver signals to the process anyway. Even worse, the
sanity check for the value of sigev_signo is skipped when SIGEV_NONE was
specified, so the signal number could be bogus. If sigev_signo was an
unitialized value (as it often would be if SIGEV_NONE is used), then
it's hard to predict which signal will be sent.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by: Richard Larocque <rlarocque@google.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Returns the time remaining for an alarm timer, rather than the time at
which it is scheduled to expire. If the timer has already expired or it
is not currently scheduled, the it_value's members are set to zero.
This new behavior matches that of the other posix-timers and the POSIX
specifications.
This is a change in user-visible behavior, and may break existing
applications. Hopefully, few users rely on the old incorrect behavior.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by: Richard Larocque <rlarocque@google.com>
[jstultz: minor style tweak] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In spite of what the GCC manual says, the -mfast-indirect-calls has
never been supported in the 64-bit parisc compiler. Indirect calls have
always been done using function descriptors irrespective of the
-mfast-indirect-calls option.
Recently, it was noticed that a function descriptor was always requested
when the -mfast-indirect-calls option was specified. This caused
problems when the option was used in application code and doesn't make
any sense because the whole point of the option is to avoid using a
function descriptor for indirect calls.
Fixing this broke 64-bit kernel builds.
I will fix GCC but for now we need the attached change. This results in
the same kernel code as before.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
return the value instead, and have path_init() do the assignment. Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination. This one should go where
it went.
To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers. And do the same to set_root(), to keep them
in sync.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Last level cache shared mask is built during CPU up and the
build_sched_domain() routine takes advantage of it to setup
the sched domain CPU topology.
However, llc_shared_mask is not released during CPU disable,
which leads to an invalid sched domainCPU topology.
This patch fix it by releasing the llc_shared_mask correctly
during CPU disable.
Yasuaki also reported that this can happen on real hardware:
https://lkml.org/lkml/2014/7/22/1018
His case is here:
==
Here is an example on my system.
My system has 4 sockets and each socket has 15 cores and HT is
enabled. In this case, each core of sockes is numbered as
follows:
Then llc_shared_mask of CPU#30 becomes
0x3fff8000fffffffc0000000. It means that last level cache of
Socket#2 is shared with CPU#30-59 and 90-104. So the mask has
the wrong value.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com> Tested-by: Linn Crosetto <linn@hp.com> Reviewed-by: Borislav Petkov <bp@suse.de> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Steven Rostedt <srostedt@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1411547885-48165-1-git-send-email-wanpeng.li@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since commit 4590685546a3 ("mm/sl[aou]b: Common alignment code"), the
"ralign" automatic variable in __kmem_cache_create() may be used as
uninitialized.
The proper alignment defaults to BYTES_PER_WORD and can be overridden by
SLAB_RED_ZONE or the alignment specified by the caller.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=85031
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Andrei Elovikov <a.elovikov@gmail.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is a deadlock case which reported by Guozhonghua:
https://oss.oracle.com/pipermail/ocfs2-devel/2014-September/010079.html
This case is caused by &res->spinlock and &dlm->master_lock
misordering in different threads.
It was introduced by commit 8d400b81cc83 ("ocfs2/dlm: Clean up refmap
helpers"). Since lockres is new, it doesn't not require the
&res->spinlock. So remove it.
Fixes: 8d400b81cc83 ("ocfs2/dlm: Clean up refmap helpers") Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Reviewed-by: joyce.xue <xuejiufei@huawei.com> Reported-by: Guozhonghua <guozhonghua@h3c.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This bug leads to reproducible silent data loss, despite the use of
msync(), sync() and a clean unmount of the file system. It is easily
reproducible with the following script:
----------------[BEGIN SCRIPT]--------------------
mkfs.nilfs2 -f /dev/sdb
mount /dev/sdb /mnt
dd if=/dev/zero bs=1M count=30 of=/mnt/testfile
umount /mnt
mount /dev/sdb /mnt
CHECKSUM_BEFORE="$(md5sum /mnt/testfile)"
So it is clear, that the changes done using mmap() do not survive a
remount. This can be reproduced a 100% of the time. The problem was
introduced in commit 136e8770cd5d ("nilfs2: fix issue of
nilfs_set_page_dirty() for page at EOF boundary").
If the page was read with mpage_readpage() or mpage_readpages() for
example, then it has no buffers attached to it. In that case
page_has_buffers(page) in nilfs_set_page_dirty() will be false.
Therefore nilfs_set_file_dirty() is never called and the pages are never
collected and never written to disk.
This patch fixes the problem by also calling nilfs_set_file_dirty() if the
page has no buffers attached to it.
[akpm@linux-foundation.org: s/PAGE_SHIFT/PAGE_CACHE_SHIFT/] Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net> Tested-by: Andreas Rohner <andreas.rohner@gmx.net> Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The C operator <= defines a perfectly fine total ordering on the set of
values representable in a long. However, unlike its namesake in the
integers, it is not translation invariant, meaning that we do not have
"b <= c" iff "a+b <= a+c" for all a,b,c.
This means that it is always wrong to try to boil down the relationship
between two longs to a question about the sign of their difference,
because the resulting relation [a LEQ b iff a-b <= 0] is neither
anti-symmetric or transitive. The former is due to -LONG_MIN==LONG_MIN
(take any two a,b with a-b = LONG_MIN; then a LEQ b and b LEQ a, but a !=
b). The latter can either be seen observing that x LEQ x+1 for all x,
implying x LEQ x+1 LEQ x+2 ... LEQ x-1 LEQ x; or more directly with the
simple example a=LONG_MIN, b=0, c=1, for which a-b < 0, b-c < 0, but a-c >
0.
Note that it makes absolutely no difference that a transmogrying bijection
has been applied before the comparison is done. In fact, had the
obfuscation not been done, one could probably not observe the bug
(assuming all values being compared always lie in one half of the address
space, the mathematical value of a-b is always representable in a long).
As it stands, one can easily obtain three file descriptors exhibiting the
non-transitivity of kcmp().
Side note 1: I can't see that ensuring the MSB of the multiplier is
set serves any purpose other than obfuscating the obfuscating code.
When calling epoll_ctl with operation EPOLL_CTL_DEL, structure epds is
not initialized but ep_take_care_of_epollwakeup reads its event field.
When this unintialized field has EPOLLWAKEUP bit set, a capability check
is done for CAP_BLOCK_SUSPEND in ep_take_care_of_epollwakeup. This
produces unexpected messages in the audit log, such as (on a system
running SELinux):
That commit was wrong since it uses data that hasn't even been set
up yet, but might be a hold-over from a previous connection.
Additionally, it seems like a driver-specific workaround that
shouldn't have been in mac80211 to start with.
Fixes: 24aa11ab8ae0 ("mac80211: disable uAPSD if all ACs are under ACM") Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe) Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Commit 2da78092 changed the locking from a mutex to a spinlock,
so we now longer sleep in this context. But there was a leftover
might_sleep() in there, which now triggers since we do the final
free from an RCU callback. Get rid of it.
Nikita Yuschenko reported that booting a kernel with init=/bin/sh and
then nfs mounting without portmap or rpcbind running using a busybox
mount resulted in:
# mount -t nfs 10.30.130.21:/opt /mnt
svc: failed to register lockdv1 RPC service (errno 111).
lockd_up: makesock failed, error=-111
Unable to handle kernel paging request for data at address 0x00000030
Faulting instruction address: 0xc055e65c
Oops: Kernel access of bad area, sig: 11 [#1]
MPC85xx CDS
Modules linked in:
CPU: 0 PID: 1338 Comm: mount Not tainted 3.10.44.cge #117
task: cf29cea0 ti: cf35c000 task.ti: cf35c000
NIP: c055e65c LR: c0566490 CTR: c055e648
REGS: cf35dad0 TRAP: 0300 Not tainted (3.10.44.cge)
MSR: 00029000 <CE,EE,ME> CR: 22442488 XER: 20000000
DEAR: 00000030, ESR: 00000000
The addition of svc_shutdown_net() resulted in two calls to
svc_rpcb_cleanup(); the second is no longer necessary and crashes when
it calls rpcb_register_call with clnt=NULL.
Reported-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru> Fixes: 679b033df484 "lockd: ensure we tear down any live sockets when socket creation fails during lockd_up" Acked-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If pcpu_map_pages() fails midway, it unmaps the already mapped pages.
Currently, it doesn't flush tlb after the partial unmapping. This may
be okay in most cases as the established mapping hasn't been used at
that point but it can go wrong and when it goes wrong it'd be
extremely difficult to track down.
When pcpu_alloc_pages() fails midway, pcpu_free_pages() is invoked to
free what has already been allocated. The invocation is across the
whole requested range and pcpu_free_pages() will try to free all
non-NULL pages; unfortunately, this is incorrect as
pcpu_get_pages_and_bitmap(), unlike what its comment suggests, doesn't
clear the pages array and thus the array may have entries from the
previous invocations making the partial failure path free incorrect
pages.
Fix it by open-coding the partial freeing of the already allocated
pages.
Currently, only SMP system free the percpu allocation info.
Uniprocessor system should free it too. For example, one x86 UML
virtual machine with 256MB memory, UML kernel wastes one page memory.
The sys_vendor / product_name are somewhat generic unfortunately, so this
may lead to some false positives. But nomux usually does no harm, where as
not having it clearly is causing problems on the Avatar AVIU-145A6.
https://bugzilla.kernel.org/show_bug.cgi?id=77391
Reported-by: Hugo P <saurosii@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We are getting more and more reports about LG laptops not having
functioning keyboard if we try to deactivate keyboard during probe.
Given that having keyboard deactivated is merely "nice to have"
instead of a hard requirement for probing, let's disable it on all
LG boxes instead of trying to hunt down particular models.
This change is prompted by patches trying to add "LG Electronics"/"ROCKY"
and "LG Electronics"/"LW60-F27B" to the DMI list.
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When running a 32-bit inputattach utility in a 64-bit system, there will be
error code "inputattach: can't set device type". This is caused by the
serport device driver not supporting compat_ioctl, so that SPIOCSTYPE ioctl
fails.
The DM crypt target accesses memory beyond allocated space resulting in
a crash on 32 bit x86 systems.
This bug is very old (it dates back to 2.6.25 commit 3a7f6c990ad04 "dm
crypt: use async crypto"). However, this bug was masked by the fact
that kmalloc rounds the size up to the next power of two. This bug
wasn't exposed until 3.17-rc1 commit 298a9fa08a ("dm crypt: use per-bio
data"). By switching to using per-bio data there was no longer any
padding beyond the end of a dm-crypt allocated memory block.
To minimize allocation overhead dm-crypt puts several structures into one
block allocated with kmalloc. The block holds struct ablkcipher_request,
cipher-specific scratch pad (crypto_ablkcipher_reqsize(any_tfm(cc))),
struct dm_crypt_request and an initialization vector.
The variable dmreq_start is set to offset of struct dm_crypt_request
within this memory block. dm-crypt allocates the block with this size:
cc->dmreq_start + sizeof(struct dm_crypt_request) + cc->iv_size.
When accessing the initialization vector, dm-crypt uses the function
iv_of_dmreq, which performs this calculation: ALIGN((unsigned long)(dmreq
+ 1), crypto_ablkcipher_alignmask(any_tfm(cc)) + 1).
dm-crypt allocated "cc->iv_size" bytes beyond the end of dm_crypt_request
structure. However, when dm-crypt accesses the initialization vector, it
takes a pointer to the end of dm_crypt_request, aligns it, and then uses
it as the initialization vector. If the end of dm_crypt_request is not
aligned on a crypto_ablkcipher_alignmask(any_tfm(cc)) boundary the
alignment causes the initialization vector to point beyond the allocated
space.
Fix this bug by calculating the variable iv_size_padding and adding it
to the allocated size.
Also correct the alignment of dm_crypt_request. struct dm_crypt_request
is specific to dm-crypt (it isn't used by the crypto subsystem at all),
so it is aligned on __alignof__(struct dm_crypt_request).
Also align per_bio_data_size on ARCH_KMALLOC_MINALIGN, so that it is
aligned as if the block was allocated with kmalloc.
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl> Tested-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a writeback or a promotion of a block is completed, the cell of
that block is removed from the prison, the block is marked as clean, and
the clear_dirty() callback of the cache policy is called.
Unfortunately, performing those actions in this order allows an incoming
new write bio for that block to come in before clearing the dirty status
is completed and therefore possibly causing one of these two scenarios:
Scenario A:
Thread 1 Thread 2
cell_defer() .
- cell removed from prison .
- detained bios queued .
. incoming write bio
. remapped to cache
. set_dirty() called,
. but block already dirty
. => it does nothing
clear_dirty() .
- block marked clean .
- policy clear_dirty() called .
Result: Block is marked clean even though it is actually dirty. No
writeback will occur.
Scenario B:
Thread 1 Thread 2
cell_defer() .
- cell removed from prison .
- detained bios queued .
clear_dirty() .
- block marked clean .
. incoming write bio
. remapped to cache
. set_dirty() called
. - block marked dirty
. - policy set_dirty() called
- policy clear_dirty() called .
Result: Block is properly marked as dirty, but policy thinks it is clean
and therefore never asks us to writeback it.
This case is visible in "dmsetup status" dirty block count (which
normally decreases to 0 on a quiet device).
Fix these issues by calling clear_dirty() before calling cell_defer().
Incoming bios for that block will then be detained in the cell and
released only after clear_dirty() has completed, so the race will not
occur.
Found by inspecting the code after noticing spurious dirty counts
(scenario B).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Releases the dev_t minor when all references are closed to prevent
another device from acquiring the same major/minor.
Since the partition's release may be invoked from call_rcu's soft-irq
context, the ext_dev_idr's mutex had to be replaced with a spinlock so
as not so sleep.
create_singlethread_workqueue() is a compat interface for single
threaded workqueue which maps to ordered workqueue w/ rescuer in the
current implementation. create_singlethread_workqueue() currently
implemented by invoking alloc_workqueue() w/ appropriate parameters.
8719dceae2f9 ("workqueue: reject adjusting max_active or applying
attrs to ordered workqueues") introduced __WQ_ORDERED to protect
ordered workqueues against dynamic attribute changes which can break
ordering guarantees but forgot to apply it to
create_singlethread_workqueue(). This in itself is okay as nobody
currently uses dynamic attribute change on workqueues created with
create_singlethread_workqueue().
However, 4c16bd327c ("workqueue: implement NUMA affinity for unbound
workqueues") broke singlethreaded guarantee for ordered workqueues
through allocating a separate pool_workqueue on each NUMA node by
default. A later change 8a2b75384444 ("workqueue: fix ordered
workqueues in NUMA setups") fixed it by allocating only one global
pool_workqueue if __WQ_ORDERED is set.
Combined, the __WQ_ORDERED omission in create_singlethread_workqueue()
became critical breaking its single threadedness and ordering
guarantee.
Let's make create_singlethread_workqueue() wrap
alloc_ordered_workqueue() instead so that it inherits __WQ_ORDERED and
can implicitly track future ordered_workqueue changes.
v2: I missed that __WQ_ORDERED now protects against pwq splitting
across NUMA nodes and incorrectly described the patch as a
nice-to-have fix to protect against future dynamic attribute
usages. Oleg pointed out that this is actually a critical
breakage due to 8a2b75384444 ("workqueue: fix ordered workqueues
in NUMA setups").
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Anderson <mike.anderson@us.ibm.com> Cc: Oleg Nesterov <onestero@redhat.com> Cc: Gustavo Luiz Duarte <gduarte@redhat.com> Cc: Tomas Henzl <thenzl@redhat.com> Fixes: 4c16bd327c ("workqueue: implement NUMA affinity for unbound workqueues") Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / linux-stable / log