In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c04 ("clk: gate: add CLK_GATE_HIWORD_MASK") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible") Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Eric Bree <ebree@nltinc.com> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.
Reported-by: Bill Augur <bill-auger@programmer.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Acked-by: Aaron Lu <aaron.lu@intel.com>
[ rjw: Fixed up the new comment in acpi_video_init() ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion
on conflicting mappings") needs to properly check for VARIABLE reports
as well (ARRAY reports should be ignored), otherwise legitimate keyboards
might break.
Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings") Reported-by: Fredrik Hallenberg <megahallon@gmail.com> Reported-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
(Note that the number of keys is the same, but key '5' is moved down and
the shape of key '4' is changed. Keys '1' to '3' are exactly the same.)
The keys 1-4 report the same scan-code in HID in both layouts, even though
the keysym they produce is usually different depending on the XKB-keymap
used by user-space.
However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout
and 0x32 for the lower layout, as defined by the HID spec. This is highly
confusing as the linux-input API uses a single keycode for both.
So far, this was never a problem as there never has been a keyboard with
both of those keys present at the same time. It would have to look
something like this:
HID can represent such a keyboard, but the linux-input API cannot.
Furthermore, any user-space mapping would be confused by this and,
luckily, no-one ever produced such hardware.
Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to
the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys
is present on a hardware, this works just fine.
Lets introduce hardware-vendors into this:
------------------------------------------
Unfortunately, it seems way to expensive to produce a different device for
American and European layouts. Therefore, hardware-vendors put both keys,
(0x31 and 0x32) on the same keyboard, but only one of them is hooked up
to the physical button, the other one is 'dead'.
This means, they can use the same hardware, with a different button-layout
and automatically produce the correct HID events for American *and*
European layouts. This is unproblematic for normal keyboards, as the
'dead' key will never report any KEY-DOWN events. But RollOver keyboards
send the whole matrix on each key-event, allowing n-key roll-over mode.
This means, we get a 0x31 and 0x32 event on each key-press. One of them
will always be 0, the other reports the real state. As we map both to the
same keycode, we will get spurious key-events, even though the real
key-state never changed.
The easiest way would be to blacklist 'dead' keys and never handle those.
We could simply read the 'country' tag of USB devices and blacklist either
key according to the layout. But... hardware vendors... want the same
device for all countries and thus many of them set 'country' to 0 for all
devices. Meh..
So we have to deal with this properly. As we cannot know which of the keys
is 'dead', we either need a heuristic and track those keys, or we simply
make use of our value-tracking for HID fields. We simply ignore HID events
for absolute data if the data didn't change. As HID tracks events on the
HID level, we haven't done the keycode translation, yet. Therefore, the
'dead' key is tracked independently of the real key, therefore, any events
on it will be ignored.
This patch simply discards any HID events for absolute data if it didn't
change compared to the last report. We need to ignore relative and
buffered-byte reports for obvious reasons. But those cannot be affected by
this bug, so we're fine.
Preferably, we'd do this filtering on the HID-core level. But this might
break a lot of custom drivers, if they do not follow the HID specs.
Therefore, we do this late in hid-input just before we inject it into the
input layer (which does the exact same filtering, but on the keycode
level).
If this turns out to break some devices, we might have to limit filtering
to EV_KEY events. But lets try to do the Right Thing first, and properly
filter any absolute data that didn't change.
This patch is tagged for 'stable' as it fixes a lot of n-key RollOver
hardware. We might wanna wait with backporting for a while, before we know
it doesn't break anything else, though.
Reported-by: Adam Goode <adam@spicenitz.org> Reported-by: Fredrik Hallenberg <megahallon@gmail.com> Tested-by: Fredrik Hallenberg <megahallon@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero. Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.
pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences s->origin. These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.
This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.
The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.
dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.
There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.
To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.
I created a dm-raid1 device backed by a device that supports DISCARD
and another device that does NOT support DISCARD with the following
dm configuration:
Notice that the mirror device /dev/mapper/moo advertises DISCARD
support even though one of the mirror halves doesn't.
If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl
BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite
loop in do_region() when it tries to issue a DISCARD request to sdb.
The problem is that when we call do_region() against sdb, num_sectors
is set to zero because q->limits.max_discard_sectors is zero.
Therefore, "remaining" never decreases and the loop never terminates.
To fix this: before entering the loop, check for the combination of
REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up
the mirror device.
This bug was found by the unfortunate coincidence of pvmove and a
discard operation in the RHEL 6.5 kernel; upstream is also affected.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver. It may also happen if the
underlying devices are moved from one disk on another.
If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.
This patch fixes failed test shell/lvconvert-repair-transient.sh in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.
`do_cmd_ioctl()` in "comedi_fops.c" handles the `COMEDI_CMD` ioctl.
This returns `-EAGAIN` if it has copied a modified `struct comedi_cmd`
back to user-space. (This occurs when the low-level Comedi driver's
`do_cmdtest()` handler returns non-zero to indicate a problem with the
contents of the `struct comedi_cmd`, or when the `struct comedi_cmd` has
the `CMDF_BOGUS` flag set.)
`compat_cmd()` in "comedi_compat32.c" handles the 32-bit compatible
version of the `COMEDI_CMD` ioctl. Currently, it never copies a 32-bit
compatible version of `struct comedi_cmd` back to user-space, which is
at odds with the way the regular `COMEDI_CMD` ioctl is handled. To fix
it, change `compat_cmd()` to copy a 32-bit compatible version of the
`struct comedi_cmd` back to user-space when the main ioctl handler
returns `-EAGAIN`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.
Cc: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The CPU_2X clock does not have a classical in-kernel user, but is,
amongst other things, required for OCM and debug access. Make sure this
clock is not mistakenly disabled during boot up by enabling it in the
platform's clock driver.
DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should
be set to 32.
The 64 was introduced by commit (in 2009): a152ff24b978 ASoC: OMAP: Make DMA 64 aligned
But the dma_mask and coherent_dma_mask can not be used to specify
alignment.
Fixes: a152ff24b978 (ASoC: OMAP: Make DMA 64 aligned) Reported-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Each inode of nilfs2 stores a root node of a b-tree, and it turned out to
have a memory overrun issue:
Each b-tree node of nilfs2 stores a set of key-value pairs and the number
of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as
a few other "bn_*" members.
Since the value of "bn_nchildren" is used for operations on the key-values
within the b-tree node, it can cause memory access overrun if a large
number is incorrectly set to "bn_nchildren".
For instance, nilfs_btree_node_lookup() function determines the range of
binary search with it, and too large "bn_nchildren" leads
nilfs_btree_node_get_key() in that function to overrun.
As for intermediate b-tree nodes, this is prevented by a sanity check
performed when each node is read from a drive, however, no sanity check
has been done for root nodes stored in inodes.
This patch fixes the issue by adding missing sanity check against b-tree
root nodes so that it's called when on-memory inodes are read from ifile,
inode metadata file.
We have a race condition between move_pages() and freeing hugepages, where
move_pages() calls follow_page(FOLL_GET) for hugepages internally and
tries to get its refcount without preventing concurrent freeing. This
race crashes the kernel, so this patch fixes it by moving FOLL_GET code
for hugepages into follow_huge_pmd() with taking the page table lock.
This patch intentionally removes page==NULL check after pte_page.
This is justified because pte_page() never returns NULL for any
architectures or configurations.
This patch changes the behavior of follow_huge_pmd() for tail pages and
then tail pages can be pinned/returned. So the caller must be changed to
properly handle the returned tail pages.
We could have a choice to add the similar locking to
follow_huge_(addr|pud) for consistency, but it's not necessary because
currently these functions don't support FOLL_GET flag, so let's leave it
for future development.
int main(int argc, char *argv[]) {
int i;
int nr_hp = strtol(argv[1], NULL, 0);
int nr_p = nr_hp * HPS / PS;
int ret;
void **addrs;
int *status;
int *nodes;
pid_t pid;
Currently we have many duplicates in definitions around
follow_huge_addr(), follow_huge_pmd(), and follow_huge_pud(), so this
patch tries to remove the m. The basic idea is to put the default
implementation for these functions in mm/hugetlb.c as weak symbols
(regardless of CONFIG_ARCH_WANT_GENERAL_HUGETL B), and to implement
arch-specific code only when the arch needs it.
For follow_huge_addr(), only powerpc and ia64 have their own
implementation, and in all other architectures this function just returns
ERR_PTR(-EINVAL). So this patch sets returning ERR_PTR(-EINVAL) as
default.
As for follow_huge_(pmd|pud)(), if (pmd|pud)_huge() is implemented to
always return 0 in your architecture (like in ia64 or sparc,) it's never
called (the callsite is optimized away) no matter how implemented it is.
So in such architectures, we don't need arch-specific implementation.
In some architecture (like mips, s390 and tile,) their current
arch-specific follow_huge_(pmd|pud)() are effectively identical with the
common code, so this patch lets these architecture use the common code.
One exception is metag, where pmd_huge() could return non-zero but it
expects follow_huge_pmd() to always return NULL. This means that we need
arch-specific implementation which returns NULL. This behavior looks
strange to me (because non-zero pmd_huge() implies that the architecture
supports PMD-based hugepage, so follow_huge_pmd() can/should return some
relevant value,) but that's beyond this cleanup patch, so let's keep it.
Justification of non-trivial changes:
- in s390, follow_huge_pmd() checks !MACHINE_HAS_HPAGE at first, and this
patch removes the check. This is OK because we can assume MACHINE_HAS_HPAGE
is true when follow_huge_pmd() can be called (note that pmd_huge() has
the same check and always returns 0 for !MACHINE_HAS_HPAGE.)
- in s390 and mips, we use HPAGE_MASK instead of PMD_MASK as done in common
code. This patch forces these archs use PMD_MASK, but it's OK because
they are identical in both archs.
In s390, both of HPAGE_SHIFT and PMD_SHIFT are 20.
In mips, HPAGE_SHIFT is defined as (PAGE_SHIFT + PAGE_SHIFT - 3) and
PMD_SHIFT is define as (PAGE_SHIFT + PAGE_SHIFT + PTE_ORDER - 3), but
PTE_ORDER is always 0, so these are identical.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A race condition starts to be visible in recent mmotm, where a PG_hwpoison
flag is set on a migration source page *before* it's back in buddy page
poo= l.
This is problematic because no page flag is supposed to be set when
freeing (see __free_one_page().) So the user-visible effect of this race
is that it could trigger the BUG_ON() when soft-offlining is called.
The root cause is that we call lru_add_drain_all() to make sure that the
page is in buddy, but that doesn't work because this function just
schedule= s a work item and doesn't wait its completion.
drain_all_pages() does drainin= g directly, so simply dropping
lru_add_drain_all() solves this problem.
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.
These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state. This patch covers that overlooked case.
Ben Hutchings [Thu, 29 Jan 2015 02:50:33 +0000 (02:50 +0000)]
splice: Apply generic position and size checks to each write
We need to check the position and size of file writes against various
limits, using generic_write_check(). This was not being done for
the splice write path. It was fixed upstream by commit 8d0207652cbe
("->splice_write() via ->write_iter()") but we can't apply that.
CVE-2014-7822
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[ kamal: port to 3.13-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The stack guard page error case has long incorrectly caused a SIGBUS
rather than a SIGSEGV, but nobody actually noticed until commit fee7e49d4514 ("mm: propagate error from stack expansion even for guard
page") because that error case was never actually triggered in any
normal situations.
Now that we actually report the error, people noticed the wrong signal
that resulted. So far, only the test suite of libsigsegv seems to have
actually cared, but there are real applications that use libsigsegv, so
let's not wait for any of those to break.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de> Tested-by: Jan Engelhardt <jengelh@inai.de> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots" Cc: linux-arch@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.
That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works. However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.
In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV. And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.
However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d4514 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space. And user space really
expected SIGSEGV, not SIGBUS.
To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it. They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.
This is the mindless minimal patch to do this. A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.
Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de> Tested-by: Jan Engelhardt <jengelh@inai.de> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots" Cc: linux-arch@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This replaces four copies in various stages of mm_fault_error() handling
with just a single one. It will also allow for more natural placement
of the unlocking after some further cleanup.
In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works.
However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver.
Declaration of the Denso cradles I tested:
- both models have the same IDs: vendorID 0x076d, productID 0x0006
- older model: Denso CU-321 (descriptors not properly set)
- later model: Denso CU-821 (with proper descriptors)
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Surface Pro 3 Type Cover that works with Ubuntu (and possibly Arch) from this thread. Both trackpad and keyboard work after compiling my own kernel.
http://ubuntuforums.org/showthread.php?t=2231207&page=2&s=44910e0c56047e4f93dfd9fea58121ef
Also includes Jarrad Whitaker's message which sources
http://winaero.com/blog/how-to-install-linux-on-surface-pro-3/
which he says is sourced from a Russian site
The Microsoft Office keyboard has a scrollwheel as well as some special keys
above the keypad which are handled through the custom MS usage page, this
commit adds support for these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
/proc/<pid>/maps currently don't annotate stack vma with "[stack]"
This is because KSTK_ESP ie expected to return usermode SP of tsk while
currently it returns the kernel mode SP of a sleeping tsk.
While the fix is trivial, we also need to adjust the ARC kernel stack
unwinder to not use KSTK_SP and friends any more.
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add missing error handling when registering the tty device at port
probe. This avoids trying to remove an uninitialised character device
when the port device is removed.
Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.
Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove
at the right times") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Greg Kroah-Hartman <greg@kroah.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com> Tested-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.
Steps: 2
[ftdi_sio_ids.h]
1. Defined the device PID
[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.
Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
These product identifiers (PID) all deal with marine NMEA format data
used on motor boats and yachts. We supply the programmed devices to
Chetco, for use inside their equipment. The PIDs are a direct copy of
our Windows device drivers (FTDI drivers with altered PIDs).
Signed-off-by: Mark Glover <mark@actisense.com>
[johan: edit commit message slightly ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dave Mielke <dave@mielke.cc> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.
Signed-off-by: Michiel van de Garde <mgparser@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.
Lets save the actual PC in the structure so that the correct value is
accessible later.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165f384f3a46b60a1be9aba4bc3c2adad Fixes: 16518d5ada690643453eb0aef3cc7841d3623c2d Reported-by: Erik Rull <erik.rull@rdsoftware.de> Tested-by: Erik Rull <erik.rull@rdsoftware.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When using the fast file fsync code path we can miss the fact that new
writes happened since the last file fsync and therefore return without
waiting for the IO to finish and write the new extents to the fsync log.
Here's an example scenario where the fsync will miss the fact that new
file data exists that wasn't yet durably persisted:
1. fs_info->last_trans_committed == N - 1 and current transaction is
transaction N (fs_info->generation == N);
2. do a buffered write;
3. fsync our inode, this clears our inode's full sync flag, starts
an ordered extent and waits for it to complete - when it completes
at btrfs_finish_ordered_io(), the inode's last_trans is set to the
value N (via btrfs_update_inode_fallback -> btrfs_update_inode ->
btrfs_set_inode_last_trans);
4. transaction N is committed, so fs_info->last_trans_committed is now
set to the value N and fs_info->generation remains with the value N;
5. do another buffered write, when this happens btrfs_file_write_iter
sets our inode's last_trans to the value N + 1 (that is
fs_info->generation + 1 == N + 1);
6. transaction N + 1 is started and fs_info->generation now has the
value N + 1;
7. transaction N + 1 is committed, so fs_info->last_trans_committed
is set to the value N + 1;
8. fsync our inode - because it doesn't have the full sync flag set,
we only start the ordered extent, we don't wait for it to complete
(only in a later phase) therefore its last_trans field has the
value N + 1 set previously by btrfs_file_write_iter(), and so we
have:
Which made us not log the last buffered write and exit the fsync
handler immediately, returning success (0) to user space and resulting
in data loss after a crash.
This can actually be triggered deterministically and the following excerpt
from a testcase I made for xfstests triggers the issue. It moves a dummy
file across directories and then fsyncs the old parent directory - this
is just to trigger a transaction commit, so moving files around isn't
directly related to the issue but it was chosen because running 'sync' for
example does more than just committing the current transaction, as it
flushes/waits for all file data to be persisted. The issue can also happen
at random periods, since the transaction kthread periodicaly commits the
current transaction (about every 30 seconds by default).
The body of the test is:
# Create our main test file 'foo', the one we check for data loss.
# By doing an fsync against our file, it makes btrfs clear the 'needs_full_sync'
# bit from its flags (btrfs inode specific flags).
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0 8K" \
-c "fsync" $SCRATCH_MNT/foo | _filter_xfs_io
# Now create one other file and 2 directories. We will move this second file
# from one directory to the other later because it forces btrfs to commit its
# currently open transaction if we fsync the old parent directory. This is
# necessary to trigger the data loss bug that affected btrfs.
mkdir $SCRATCH_MNT/testdir_1
touch $SCRATCH_MNT/testdir_1/bar
mkdir $SCRATCH_MNT/testdir_2
# Make sure everything is durably persisted.
sync
# Write more 8Kb of data to our file.
$XFS_IO_PROG -c "pwrite -S 0xbb 8K 8K" $SCRATCH_MNT/foo | _filter_xfs_io
# Move our 'bar' file into a new directory.
mv $SCRATCH_MNT/testdir_1/bar $SCRATCH_MNT/testdir_2/bar
# Fsync our first directory. Because it had a file moved into some other
# directory, this made btrfs commit the currently open transaction. This is
# a condition necessary to trigger the data loss bug.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir_1
# Now fsync our main test file. If the fsync succeeds, we expect the 8Kb of
# data we wrote previously to be persisted and available if a crash happens.
# This did not happen with btrfs, because of the transaction commit that
# happened when we fsynced the parent directory.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Now check that all data we wrote before are available.
echo "File content after log replay:"
od -t x1 $SCRATCH_MNT/foo
status=0
exit
The expected golden output for the test, which is what we get with this
fix applied (or when running against ext3/4 and xfs), is:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
* 0040000
Without this fix applied, the output shows the test file does not have
the second 8Kb extent that we successfully fsynced:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay: 0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
* 0020000
So fix this by skipping the fsync only if we're doing a full sync and
if the inode's last_trans is <= fs_info->last_trans_committed, or if
the inode is already in the log. Also remove setting the inode's
last_trans in btrfs_file_write_iter since it's useless/unreliable.
Also because btrfs_file_write_iter no longer sets inode->last_trans to
fs_info->generation + 1, don't set last_trans to 0 if we bail out and don't
bail out if last_trans is 0, otherwise something as simple as the following
example wouldn't log the second write on the last fsync:
1. write to file
2. fsync file
3. fsync file
|--> btrfs_inode_in_log() returns true and it set last_trans to 0
4. write to file
|--> btrfs_file_write_iter() no longers sets last_trans, so it
remained with a value of 0
5. fsync
|--> inode->last_trans == 0, so it bails out without logging the
second write
A test case for xfstests will be sent soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A block-local variable stores error code but btrfs_get_blocks_direct may
not return it in the end as there's a ret defined in the function scope.
Fixes: d187663ef24c ("Btrfs: lock extents as we map them in DIO") Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Set the internal device state to to disabled after hardware reset in stop flow.
This will cover cases when driver was not brought to disabled state because of
an error and in stop flow we wish not to retry the reset.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Emit the EOP twice to avoid cache flushing problems.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Enable at init and disable on fini. Workaround for hardware problems.
v2 (chk): extend commit message
v3: add new function
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> (v2) Signed-off-by: Jiri Slaby <jslaby@suse.cz>
For whatever reason, generic_access_phys() only remaps one page, but
actually allows to access arbitrary size. It's quite easy to trigger
large reads, like printing out large structure with gdb, which leads to a
crash. Fix it by remapping correct size.
What we want to check here is whether there is highorder freepage in buddy
list of other migratetype in order to steal it without fragmentation.
But, current code just checks cc->order which means allocation request
order. So, this is wrong.
Without this fix, non-movable synchronous compaction below pageblock order
would not stopped until compaction is complete, because migratetype of
most pageblocks are movable and high order freepage made by compaction is
usually on movable type buddy list.
There is some report related to this bug. See below link.
Although the issued system still has load spike comes from compaction,
this makes that system completely stable and responsive according to his
report.
stress-highalloc test in mmtests with non movable order 7 allocation
doesn't show any notable difference in allocation success rate, but, it
shows more compaction success rate.
I noticed that "allowed" can easily overflow by falling below 0, because
(total_vm / 32) can be larger than "allowed". The problem occurs in
OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
I noticed, that "allowed" can easily overflow by falling below 0,
because (total_vm / 32) can be larger than "allowed". The problem
occurs in OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
[akpm@linux-foundation.org: use min_t] Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If __unmap_hugepage_range() tries to unmap the address range over which
hugepage migration is on the way, we get the wrong page because pte_page()
doesn't work for migration entries. This patch simply clears the pte for
migration entries as we do for hwpoison entries.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is a race condition between hugepage migration and
change_protection(), where hugetlb_change_protection() doesn't care about
migration entries and wrongly overwrites them. That causes unexpected
results like kernel crash. HWPoison entries also can cause the same
problem.
This patch adds is_hugetlb_entry_(migration|hwpoisoned) check in this
function to do proper actions.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device" Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
1. For an IPv4 ping socket, ping_check_bind_addr does not check
the family of the socket address that's passed in. Instead,
make it behave like inet_bind, which enforces either that the
address family is AF_INET, or that the family is AF_UNSPEC and
the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
if the socket family is not AF_INET6. Return EAFNOSUPPORT
instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
instead of EINVAL if an incorrect socket address structure is
passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
IPv4, and it cannot easily be made to support IPv4 because
the protocol numbers for ICMP and ICMPv6 are different. This
makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
of making the socket unusable.
Among other things, this fixes an oops that can be triggered by:
Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241 Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com> Tested-by: Brian Rak <brak@vultr.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
With commit a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a0518a, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).
On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d06b.
This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a0518a.
The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).
Fixes: a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg) Cc: Andy Lutomirski <luto@amacapital.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In tcf_em_validate(), after calling request_module() to load the
kind-specific module, set em->ops to NULL before returning -EAGAIN, so
that module_put() is not called again by tcf_em_tree_destroy().
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr> Acked-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34e6 ("net: phy: fix a bug when verify the EEE support") Fixes: 3e7077067e80c ("phy: Expand phy speed/duplex settings array") Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().
Fixes: 1bf3751ec90c ("ipv4: ip_check_defrag must not modify skb before unsharing") Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The gnet_stats_copy_app() function gets called, more often than not, with its
second argument a pointer to an automatic variable in the caller's stack.
Therefore, to avoid copying garbage afterwards when calling
gnet_stats_finish_copy(), this data is better copied to a dynamically allocated
memory that gets freed after use.
[xiyou.wangcong@gmail.com: remove a useless kfree()]
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Ignacy reported that when eth0 is down and add a vlan device
on top of it like:
ip link add link eth0 name eth0.1 up type vlan id 1
We will get a refcount leak:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 2
The problem is when rtnl_configure_link() fails in rtnl_newlink(),
we simply call unregister_device(), but for stacked device like vlan,
we almost do nothing when we unregister the upper device, more work
is done when we unregister the lower device, so call its ->dellink().
Reported-by: Ignacy Gawedzki <ignacy.gawedzki@green-communications.fr> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / linux-stable / log