Add some missing hid usages from consumer page, add
some display brightness control usages from approved hid usage
table request HUTTR41:
http://www.usb.org/developers/hidpage/HUTRR41.pdf
and add voice command usage from approved request HUTTR45:
http://www.usb.org/developers/hidpage/Voice_Command_Usage.pdf
[jkosina@suse.cz: removed KEY_BRIGHTNESS_TOGGLE / KEY_DISPLAYTOGGLE
conflict from hid-debug.c]
Add mapping for "AL Next Task/Application", "AL Previous Task/Application"
and "AL File Browser" buttons, as found on the Microsoft Office keyboard.
Note that there already is a mapping for "AL Local Machine Browser" to
KEY_FILE. Unless we ever encounter a device with both that should not be
a problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix issue with the sleeping calling hid_hw_request under spinlock.
When i2c is used as HID transport, this is calling kmalloc, which
can sleep. So remove call to this function while under spinlock.
[ 1067.021961] Call Trace:
[ 1067.021970] [<ffffffff8192f5f2>] dump_stack+0x4d/0x6f
[ 1067.021976] [<ffffffff811109f2>] __might_sleep+0xd2/0xf0
[ 1067.021981] [<ffffffff811ea15b>] __kmalloc+0xeb/0x200
[ 1067.021989] [<ffffffff816e0cb3>] ? hid_alloc_report_buf+0x23/0x30
[ 1067.021993] [<ffffffff816e0cb3>] hid_alloc_report_buf+0x23/0x30
[ 1067.021997] [<ffffffff816f4cb7>] i2c_hid_request+0x57/0x110
[ 1067.022006] [<ffffffffa02bc61c>] sensor_hub_input_attr_get_raw_value+0xbc/0x100 [hid_sensor_hub]
Multitouch touchpads built for Win 8.1 need to be sent an input mode feature report
in order to start reporting multitouch events. This is the same process sent
to Win 7 multitouch touchscreens except the value of the feature report is 3 for
touchpads.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It has been reported that there is a new hardware version of the G27
in the 'wild'. This patch add's this new revision so that it can be
sent the command to switch to native mode.
We need at least HID_MAX_BUFFER_SIZE (4096) bytes as input buffer. HID
core depends on this as it requires every input report to be at least as
big as advertised.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On r-/sh-mobile SoCs MSTP clocks are used by the runtime PM to dynamically
enable and disable peripheral clocks. To make sure the clock has really
started we have to read back its status register until it confirms success.
On R-Mobile APE6, since it has 3 thermal zones, ENR register
has enable bits in bit 19-16, bit 11-8 and bit 3-0.
However, on R-Car gen2, since it has 1 thermal zone, ENR register has
enable bits in bit 3-0. (In other words, the write value should always
be 0 for bit 31-4 of ENR register.)
So, this patch fixes the ENR register value using I/O resource sets.
It turns out that some boards can have instance->lower greater than 0 and
when thermal trend is dropping it results with next_target equal to -1.
Since the next_target is defined as unsigned long it is interpreted as
0xFFFFFFFF and larger than instance->upper.
As a result the next_target is set to instance->upper which ramps up to
maximal cooling device target when the temperature is steadily decreasing.
Since commit bd31b85960a7 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.
This fixes:
drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
spin_lock_irqsave(&nw_gpio_lock, flags);
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
^
drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
spin_unlock_irqrestore(&nw_gpio_lock, flags);
^
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com> Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.
Log:
PM: noirq freeze of devices complete after 1.425 msecs
Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)
WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access
CPU1: shutdown
^ or here
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Fixes: 73e1ab41a80d (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since commit 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.
Fix the binding documentation so the property is properly specified.
Fixes: 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data") Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The way the mask is generated in regmap_field_init() is wrong.
Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift
overflow while calculating the mask field.
On some 32 bits architectures, such as x86, the generated mask is 0,
instead of the expected 0xffffffff.
This patch uses GENMASK() to fix the problem, as this macro is already safe
regarding shift overflow.
[-js: in 3.12, we do not have GENMASK for general access. Define
locally as RM_GENMASK.]
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In big endian mode regmap_bulk_read gives incorrect data
for byte reads.
This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.
Signed-off-by: Arun Chandran <achandran@mvista.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If there is a PM QoS latency limit and all of the sufficiently shallow
C-states are disabled, the cpuidle menu governor returns 0 which on
some systems is CPUIDLE_DRIVER_STATE_START and shouldn't be returned
if that C-state has been disabled.
Fix the issue by modifying the menu governor to return (-1) in such
situations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[shilpab: Backport to 3.10.y
- adjust context
- add a check if 'next_state' is less than 0 in 'cpuidle_idle_call()',
this ensures that we exit 'cpuidle_idle_call()' if governor->select()
returns negative value] Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When building the kernel with a bare-metal (ELF) toolchain, the -shared
option may not be passed down to collect2, resulting in silent corruption
of the vDSO image (in particular, the DYNAMIC section is omitted).
The effect of this corruption is that the dynamic linker fails to find
the vDSO symbols and libc is instead used for the syscalls that we
intended to optimise (e.g. gettimeofday). Functionally, there is no
issue as the sigreturn trampoline is still intact and located by the
kernel.
This patch fixes the problem by explicitly passing -shared to the linker
when building the vDSO.
Reported-by: Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by: James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.
This may cause memmap entries that are in use to get freed.
In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.
This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.
This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Disable write buffering on the Toshiba ToPIC95 if it is enabled by
somebody (it is not supposed to be a power-on default according to
the datasheet). On the ToPIC95, practically no 32-bit Cardbus card
will work under heavy load without locking up the whole system if
this is left enabled. I tried about a dozen. It does not affect
16-bit cards. This is similar to the O2 bugs in early controller
revisions it seems.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961 Signed-off-by: Ryan C. Underwood <nemesis@icequake.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If, at the time __rcu_process_callbacks() is invoked, there are callbacks
in Tiny RCU's callback list, but none of them are ready to be invoked,
the current list-management code will knit the non-ready callbacks out
of the list. This can result in hangs and possibly worse. This commit
therefore inserts a check for there being no callbacks that can be
invoked immediately.
This bug is unlikely to occur -- you have to get a new callback between
the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to
__rcu_process_callbacks(). It was detected by the addition of RCU-bh
testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's
mutation testing. Although this bug was made much more likely by 915e8a4fe45e (rcu: Remove fastpath from __rcu_process_callbacks()), this
did not cause the bug, but rather made it much more probable. That
said, it takes more than 40 hours of rcutorture testing, on average,
for this bug to appear, so this fix cannot be considered an emergency.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We enable _CRS on all systems from 2008 and later. On older systems, we
ignore _CRS and assume the whole physical address space (excluding RAM and
other devices) is available for PCI devices, but on systems that support
physical address spaces larger than 4GB, it's doubtful that the area above
4GB is really available for PCI.
After d56dbf5bab8c ("PCI: Allocate 64-bit BARs above 4G when possible"), we
try to use that space above 4GB *first*, so we're more likely to put a
device there.
On Juan's Toshiba Satellite Pro U200, BIOS left the graphics, sound, 1394,
and card reader devices unassigned (but only after Windows had been
booted). Only the sound device had a 64-bit BAR, so it was the only device
placed above 4GB, and hence the only device that didn't work.
Keep _CRS enabled even on pre-2008 systems if they support physical address
space larger than 4GB.
Limit the mounts fs_fully_visible considers to locked mounts.
Unlocked can always be unmounted so considering them adds hassle
but no security benefit.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The warning message in prepend_path is unclear and outdated. It was
added as a warning that the mechanism for generating names of pseudo
files had been removed from prepend_path and d_dname should be used
instead. Unfortunately the warning reads like a general warning,
making it unclear what to do with it.
Remove the warning. The transition it was added to warn about is long
over, and I added code several years ago which in rare cases causes
the warning to fire on legitimate code, and the warning is now firing
and scaring people for no good reason.
Reported-by: Ivan Delalande <colona@arista.com> Reported-by: Omar Sandoval <osandov@osandov.com> Fixes: f48cfddc6729e ("vfs: In d_path don't call d_dname on a mount point") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
file_remove_suid() could mistakenly set S_NOSEC inode bit when root was
modifying the file. As a result following writes to the file by ordinary
user would avoid clearing suid or sgid bits.
Fix the bug by checking actual mode bits before setting S_NOSEC.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Writes were a bit racy, but hard to turn into a bug at the same time.
(Particularly because modern Linux doesn't use this feature anymore.)
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Actually the next patch makes it much, much easier to trigger the race
so I'm including this one for stable@ as well. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
KVM guest kernels for trap & emulate run in user mode, with a modified
set of kernel memory segments. However the fixmap address is still in
the normal KSeg3 region at 0xfffe0000 regardless, causing problems when
cache alias handling makes use of them when handling copy on write.
Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped
region when CONFIG_KVM_GUEST is defined.
The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign
resources correctly without the information from _CRS that tells us which
address ranges are claimed by which bridge. In the bugs mentioned below,
we incorrectly assign a sound card address (this example is from 1033299):
When we take a PMU exception or a software event we call
perf_read_regs(). This overloads regs->result with a boolean that
describes if we should use the sampled instruction address register
(SIAR) or the regs.
If the exception is in kernel, we start with the kernel regs and
backtrace through the kernel stack. At this point we switch to the
userspace regs and backtrace the user stack with perf_callchain_user().
Unfortunately these regs have not got the perf_read_regs() treatment,
so regs->result could be anything. If it is non zero,
perf_instruction_pointer() decides to use the SIAR, and we get issues
like this:
On VM entry, we disable access to the VFP registers in order to
perform a lazy save/restore of these registers.
On VM exit, we restore access, test if we did enable them before,
and save/restore the guest/host registers if necessary. In this
sequence, the FPEXC register is always accessed, irrespective
of the trapping configuration.
If the guest didn't touch the VFP registers, then the HCPTR access
has now enabled such access, but we're missing a barrier to ensure
architectural execution of the new HCPTR configuration. If the HCPTR
access has been delayed/reordered, the subsequent access to FPEXC
will cause a trap, which we aren't prepared to handle at all.
The same condition exists when trapping to enable VFP for the guest.
The fix is to introduce a barrier after enabling VFP access. In the
vmexit case, it can be relaxed to only takes place if the guest hasn't
accessed its view of the VFP registers, making the access to FPEXC safe.
The set_hcptr macro is modified to deal with both vmenter/vmexit and
vmtrap operations, and now takes an optional label that is branched to
when the guest hasn't touched the VFP registers.
The conversion to be16_add_cpu() is incorrect in case cryptlen is
negative due to premature (i.e. before addition / subtraction)
implicit conversion of cryptlen (int -> u16) leading to sign loss.
Fixes: 1d11911a8c57 ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function") Signed-off-by: Horia Geanta <horia.geanta@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is NULL pointer dereference possible during statistics update if the route
used for OOTB responce is removed at unfortunate time. If the route exists when
we receive OOTB packet and we finally jump into sctp_packet_transmit() to send
ABORT, but in the meantime route is removed under our feet, we take "no_route"
path and try to update stats with IP_INC_STATS(sock_net(asoc->base.sk), ...).
But sctp_ootb_pkt_new() used to prepare responce packet doesn't call
sctp_transport_set_owner() and therefore there is no asoc associated with this
packet. Probably temporary asoc just for OOTB responces is overkill, so just
introduce a check like in all other places in sctp_packet_transmit(), where
"asoc" is dereferenced.
To reproduce this, one needs to
0. ensure that sctp module is loaded (otherwise ABORT is not generated)
1. remove default route on the machine
2. while true; do
ip route del [interface-specific route]
ip route add [interface-specific route]
done
3. send enough OOTB packets (i.e. HB REQs) from another host to trigger ABORT
responce
The lockless lookups can return entry that is unlinked.
Sometimes they get reference before last neigh_cleanup_and_release,
sometimes they do not need reference. Later, any
modification attempts may result in the following problems:
1. entry is not destroyed immediately because neigh_update
can start the timer for dead entry, eg. on change to NUD_REACHABLE
state. As result, entry lives for some time but is invisible
and out of control.
2. __neigh_event_send can run in parallel with neigh_destroy
while refcnt=0 but if timer is started and expired refcnt can
reach 0 for second time leading to second neigh_destroy and
possible crash.
Thanks to Eric Dumazet and Ying Xue for their work and analyze
on the __neigh_event_send change.
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour") Fixes: a263b3093641 ("ipv4: Make neigh lookups directly in output packet path.") Fixes: 6fd6ce2056de ("ipv6: Do not depend on rt->n in ip6_finish_output2().") Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
PACKET_FANOUT_LB computes f->rr_cur such that it is modulo
f->num_members. It returns the old value unconditionally, but
f->num_members may have changed since the last store. Ensure
that the return value is always < num.
When modifying the logic, simplify it further by replacing the loop
with an unconditional atomic increment.
Fixes: dc99f600698d ("packet: Add fanout support.") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We need to tell compiler it must not read f->num_members multiple
times. Otherwise testing if num is not zero is flaky, and we could
attempt an invalid divide by 0 in fanout_demux_cpu()
Note bug was present in packet_rcv_fanout_hash() and
packet_rcv_fanout_lb() but final 3.1 had a simple location
after commit 95ec3eb417115fb ("packet: Add 'cpu' fanout policy.")
Fixes: dc99f600698dc ("packet: Add fanout support.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
After the ->set() spinlocks were removed br_stp_set_bridge_priority
was left running without any protection when used via sysfs. It can
race with port add/del and could result in use-after-free cases and
corrupted lists. Tested by running port add/del in a loop with stp
enabled while setting priority in a loop, crashes are easily
reproducible.
The spinlocks around sysfs ->set() were removed in commit: 14f98f258f19 ("bridge: range check STP parameters")
There's also a race condition in the netlink priority support that is
fixed by this change, but it was introduced recently and the fixes tag
covers it, just in case it's needed the commit is: af615762e972 ("bridge: add ageing_time, stp_state, priority over netlink")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Fixes: 14f98f258f19 ("bridge: range check STP parameters") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
->auto_asconf_splist is per namespace and mangled by functions like
sctp_setsockopt_auto_asconf() which doesn't guarantee any serialization.
Also, the call to inet_sk_copy_descendant() was backuping
->auto_asconf_list through the copy but was not honoring
->do_auto_asconf, which could lead to list corruption if it was
different between both sockets.
This commit thus fixes the list handling by using ->addr_wq_lock
spinlock to protect the list. A special handling is done upon socket
creation and destruction for that. Error handlig on sctp_init_sock()
will never return an error after having initialized asconf, so
sctp_destroy_sock() can be called without addrq_wq_lock. The lock now
will be take on sctp_close_sock(), before locking the socket, so we
don't do it in inverse order compared to sctp_addr_wq_timeout_handler().
Instead of taking the lock on sctp_sock_migrate() for copying and
restoring the list values, it's preferred to avoid rewritting it by
implementing sctp_copy_descendant().
Issue was found with a test application that kept flipping sysctl
default_auto_asconf on and off, but one could trigger it by issuing
simultaneous setsockopt() calls on multiple sockets or by
creating/destroying sockets fast enough. This is only triggerable
locally.
Fixes: 9f7d653b67ae ("sctp: Add Auto-ASCONF support (core).") Reported-by: Ji Jianwen <jiji@redhat.com> Suggested-by: Neil Horman <nhorman@tuxdriver.com> Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We saw excessive direct memory compaction triggered by skb_page_frag_refill.
This causes performance issues and add latency. Commit 5640f7685831e0
introduces the order-3 allocation. According to the changelog, the order-3
allocation isn't a must-have but to improve performance. But direct memory
compaction has high overhead. The benefit of order-3 allocation can't
compensate the overhead of direct memory compaction.
This patch makes the order-3 page allocation atomic. If there is no memory
pressure and memory isn't fragmented, the alloction will still success, so we
don't sacrifice the order-3 benefit here. If the atomic allocation fails,
direct memory compaction will not be triggered, skb_page_frag_refill will
fallback to order-0 immediately, hence the direct memory compaction overhead is
avoided. In the allocation failure case, kswapd is waken up and doing
compaction, so chances are allocation could success next time.
alloc_skb_with_frags is the same.
The mellanox driver does similar thing, if this is accepted, we must fix
the driver too.
V3: fix the same issue in alloc_skb_with_frags as pointed out by Eric
V2: make the changelog clearer
Cc: Eric Dumazet <edumazet@google.com> Cc: Chris Mason <clm@fb.com> Cc: Debabrata Banerjee <dbavatar@gmail.com> Signed-off-by: Shaohua Li <shli@fb.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since the addition of sysfs multicast router support if one set
multicast_router to "2" more than once, then the port would be added to
the hlist every time and could end up linking to itself and thus causing an
endless loop for rlist walkers.
So to reproduce just do:
echo 2 > multicast_router; echo 2 > multicast_router;
in a bridge port and let some igmp traffic flow, for me it hangs up
in br_multicast_flood().
Fix this by adding a check in br_multicast_add_router() if the port is
already linked.
The reason this didn't happen before the addition of multicast_router
sysfs entries is because there's a !hlist_unhashed check that prevents
it.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Fixes: 0909e11758bd ("bridge: Add multicast_router sysfs entries") Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since it is possible for vnet_event_napi to end up doing
vnet_control_pkt_engine -> ... -> vnet_send_attr ->
vnet_port_alloc_tx_ring -> ldc_alloc_exp_dring -> kzalloc()
(i.e., in softirq context), kzalloc() should be called with
GFP_ATOMIC from ldc_alloc_exp_dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.com>
Since commit 8a0a9bd4db63 ('random: make get_random_int() more
random'), get_random_int() returns a random value for each call,
so comment and hack introduced in mmap_rnd() as part of commit 1d18c47c735e ('arm64: MMU fault handling and page table management')
are incorrects.
Commit 1d18c47c735e seems to use the same hack introduced by
commit a5adc91a4b44 ('powerpc: Ensure random space between stack
and mmaps'), latter copied in commit 5a0efea09f42 ('sparc64: Sharpen
address space randomization calculations.').
But both architectures were cleaned up as part of commit fa8cbaaf5a68 ('powerpc+sparc64/mm: Remove hack in mmap randomize
layout') as hack is no more needed since commit 8a0a9bd4db63.
So the present patch removes the comment and the hack around
get_random_int() on AArch64's mmap_rnd().
Cc: David S. Miller <davem@davemloft.net> Cc: Anton Blanchard <anton@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.com>
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com> Signed-off-by: Rajat Jain <rajatjain@juniper.net> Signed-off-by: Guenter Roeck <groeck@juniper.net> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[backported for SLE12] Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.com>
dst_orig should be released on error. Function like __xfrm_route_forward()
expects that behavior.
Since a recent commit, xfrm_lookup() may also be called by xfrm_lookup_route(),
which expects the opposite.
Let's introduce a new flag (XFRM_LOOKUP_KEEP_DST_REF) to tell what should be
done in case of error.
Fixes: f92ee61982d("xfrm: Generate blackhole routes only from route lookup functions") Signed-off-by: huaibin Wang <huaibin.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jiri Slaby <jslaby@suse.com>
If hardware doesn't support DecodeAssist - a feature that provides
more information about the intercept in the VMCB, KVM decodes the
instruction and then updates the next_rip vmcb control field.
However, NRIP support itself depends on cpuid Fn8000_000A_EDX[NRIPS].
Since skip_emulated_instruction() doesn't verify nrip support
before accepting control.next_rip as valid, avoid writing this
field if support isn't present.
Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Replacing a xattr consists of doing a lookup for its existing value, delete
the current value from the respective leaf, release the search path and then
finally insert the new value. This leaves a time window where readers (getxattr,
listxattrs) won't see any value for the xattr. Xattrs are used to store ACLs,
so this has security implications.
This change also fixes 2 other existing issues which were:
*) Deleting the old xattr value without verifying first if the new xattr will
fit in the existing leaf item (in case multiple xattrs are packed in the
same item due to name hash collision);
*) Returning -EEXIST when the flag XATTR_CREATE is given and the xattr doesn't
exist but we have have an existing item that packs muliple xattrs with
the same name hash as the input xattr. In this case we should return ENOSPC.
A test case for xfstests follows soon.
Thanks to Alexandre Oliva for reporting the non-atomicity of the xattr replace
implementation.
Reported-by: Alexandre Oliva <oliva@gnu.org> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The related code can be simplified, and also can avoid related warnings
(with allmodconfig under parisc):
CC [M] net/netfilter/nfnetlink_cthelper.o
net/netfilter/nfnetlink_cthelper.c: In function ‘nfnl_cthelper_from_nlattr’:
net/netfilter/nfnetlink_cthelper.c:97:9: warning: passing argument 1 o ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
memcpy(&help->data, nla_data(attr), help->helper->data_len);
^
In file included from include/linux/string.h:17:0,
from include/uapi/linux/uuid.h:25,
from include/linux/uuid.h:23,
from include/linux/mod_devicetable.h:12,
from ./arch/parisc/include/asm/hardware.h:4,
from ./arch/parisc/include/asm/processor.h:15,
from ./arch/parisc/include/asm/spinlock.h:6,
from ./arch/parisc/include/asm/atomic.h:21,
from include/linux/atomic.h:4,
from ./arch/parisc/include/asm/bitops.h:12,
from include/linux/bitops.h:36,
from include/linux/kernel.h:10,
from include/linux/list.h:8,
from include/linux/module.h:9,
from net/netfilter/nfnetlink_cthelper.c:11:
./arch/parisc/include/asm/string.h:8:8: note: expected ‘void *’ but argument is of type ‘const char (*)[]’
void * memcpy(void * dest,const void *src,size_t count);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@soleta.eu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On x86-64, __copy_instruction() always returns 0 (error) if the
instruction uses %rip-relative addressing. This is because
kernel_insn_init() is called the second time for 'insn' instance
in such cases and sets all its fields to 0.
Because of this, trying to place a kprobe on such instruction
will fail, register_kprobe() will return -EINVAL.
Ben Hutchings [Tue, 16 Jun 2015 21:11:06 +0000 (22:11 +0100)]
pipe: iovec: Fix memory corruption when retrying atomic copy as non-atomic
pipe_iov_copy_{from,to}_user() may be tried twice with the same iovec,
the first time atomically and the second time not. The second attempt
needs to continue from the iovec position, pipe buffer offset and
remaining length where the first attempt failed, but currently the
pipe buffer offset and remaining length are reset. This will corrupt
the piped data (possibly also leading to an information leak between
processes) and may also corrupt kernel memory.
This was fixed upstream by commits f0d1bec9d58d ("new helper:
copy_page_from_iter()") and 637b58c2887e ("switch pipe_read() to
copy_page_to_iter()"), but those aren't suitable for stable. This fix
for older kernel versions was made by Seth Jennings for RHEL and I
have extracted it from their update.
CVE-2015-1805
References: https://bugzilla.redhat.com/show_bug.cgi?id=1202855 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
BugLink: https://bugs.launchpad.net/bugs/1427680
This device requires new firmware files
AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.
BugLink: https://bugs.launchpad.net/bugs/1462614
This device requires new firmware files
AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.
Add a memory barrier to ensure the valid bit is read before
any of the cqe payload is read. This fixes an issue seen
on Power where the cqe payload was getting loaded before
the valid bit. When this occurred, we saw an iotag out of
range error when a command completed, but since the iotag
looked invalid the command didn't get completed to scsi core.
Later we hit the command timeout, attempted to abort the command,
then waited for the aborted command to get returned. Since the
adapter already returned the command, we timeout waiting,
and end up escalating EEH all the way to host reset. This
patch fixes this issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Smart <james.smart@emulex.com>
---
Running igt, I was encountering the invalid TLB bug on my 845g, despite
that it was using the CS workaround. Examining the w/a buffer in the
error state, showed that the copy from the user batch into the
workaround itself was suffering from the invalid TLB bug (the first
cacheline was broken with the first two words reversed). Time to try a
fresh approach. This extends the workaround to write into each page of
our scratch buffer in order to overflow the TLB and evict the invalid
entries. This could be refined to only do so after we update the GTT,
but for simplicity, we do it before each batch.
I suspect this supersedes our current workaround, but for safety keep
doing both.
V2: The magic number shall be 2.
This doesn't conclusively prove that it is the mythical TLB bug we've
been trying to workaround for so long, that it requires touching a number
of pages to prevent the corruption indicates to me that it is TLB
related, but the corruption (the reversed cacheline) is more subtle than
a TLB bug, where we would expect it to read the wrong page entirely.
Oh well, it prevents a reliable hang for me and so probably for others
as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Nikolay <mar.kolya@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The "Webmail Notifier" is a USB controlled LED that appears as a HID
device. When trying to change the LED via hidraw it returns malformed
reports. As "usbled" supports it, we blacklist it in usbhid.
The Microchip Pick16F1454 is exported as a HID device and is used by for
example the Yepkit YKUSH three-port switchable USB hub. However, it is not an
actual HID-device. On the Yepkit, it is used to power up/down the ports on the
hub. The HID driver should ignore this device.
Ignore Jabra GN9350E HID interface. USB audio is working nicely, but
registering as HID blocks USB mouse buttons. Since special userspace programs
are needed we will avoid attaching usbhid drivers in general.
The Si4713 development board contains a Si4713 FM transmitter chip
and is handled by the radio-usb-si4713 driver.
The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc.
and misidentifies itself as a HID device in its USB interface descriptor.
This patch ignores this device as an HID device and hence loads the custom driver.
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
The report descriptor for the HOLTEK USB ID 04d9:a0c2 (ETEKCITY Scroll
T-140 Gaming Mouse) is set to a very large amount of consumer usages
(2^16), exceeding HID_MAX_USAGES. Added id, bindings and comments for
the mouse, added to hid_have_special_driver, and reduced the usage and
logical maximums to 0x2fff, consistent with the other mice in the
category. Tested on the hardware.
Signed-off-by: John C. DeSilva <desilvjo@umich.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix a couple of pci id table mistakes:
Subdevice ID 0x3323 missing from product[] table
(another name for HP Smart Storage 1210m)
Bogus 0x1925 subdevice id removed from hpsa_pci_device_id[] (no such thing.)
Signed-off-by: Don Brace <don.brace@pmcs.com> Reviewed-by: Webb Scales <webbnh@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The gcc version 4.9.1 compiler complains Even though it isn't possible for
these variables to not get initialized before they are used.
fs/namespace.c: In function ‘SyS_mount’:
fs/namespace.c:2720:8: warning: ‘kernel_dev’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = do_mount(kernel_dev, kernel_dir->name, kernel_type, flags,
^
fs/namespace.c:2699:8: note: ‘kernel_dev’ was declared here
char *kernel_dev;
^
fs/namespace.c:2720:8: warning: ‘kernel_type’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = do_mount(kernel_dev, kernel_dir->name, kernel_type, flags,
^
fs/namespace.c:2697:8: note: ‘kernel_type’ was declared here
char *kernel_type;
^
Fix the warnings by simplifying copy_mount_string() as suggested by Al Viro.
Cc: Alexander Viro <viro@zeniv.linux.org.uk> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since we pass the port number through file private data for debugfs we cast
it to and from a pointer so use uintptr_t in order to ensure that the
types are compatible, avoiding warnings on 64 bit platforms where pointers
are 64 bit and unsigned integers 32 bit.
Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Make sure the value we are going to return is referenced in order to
avoid warnings from newer GCCs such as:
arch/arm64/include/asm/cmpxchg.h:162:3: warning: value computed is not used [-Wunused-value]
((__typeof__(*(ptr)))__cmpxchg_mb((ptr), \
^
net/netfilter/nf_conntrack_core.c:674:2: note: in expansion of macro ‘cmpxchg’
cmpxchg(&nf_conntrack_hash_rnd, 0, rand);
[Modified to use the current underlying implementation as current
mainline for both cmpxchg() and cmpxchg_local() does -- broonie]
Signed-off-by: Mark Hambleton <mahamble@broadcom.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Some users of xchg() don't bother using the return value, which results
in a compiler warning like the following (from kgdb):
In file included from linux/arch/arm64/include/asm/atomic.h:27:0,
from include/linux/atomic.h:4,
from include/linux/spinlock.h:402,
from include/linux/seqlock.h:35,
from include/linux/time.h:5,
from include/uapi/linux/timex.h:56,
from include/linux/timex.h:56,
from include/linux/sched.h:19,
from include/linux/pid_namespace.h:4,
from kernel/debug/debug_core.c:30:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
linux/arch/arm64/include/asm/cmpxchg.h:75:3: warning: value computed is not used [-Wunused-value]
((__typeof__(*(ptr)))__xchg((unsigned long)(x),(ptr),sizeof(*(ptr))))
^
linux/arch/arm64/include/asm/atomic.h:132:30: note: in expansion of macro ‘xchg’
#define atomic_xchg(v, new) (xchg(&((v)->counter), new))
kernel/debug/debug_core.c:504:4: note: in expansion of macro ‘atomic_xchg’
atomic_xchg(&kgdb_active, cpu);
^
This patch makes use of the same trick as we do for cmpxchg, by assigning
the return value to a dummy variable in the xchg() macro itself.
In file included from scripts/sortextable.c:194:0:
scripts/sortextable.c: In function `main':
scripts/sortextable.h:176:3: warning: `relocs_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
memset(relocs, 0, relocs_size);
^
scripts/sortextable.h:106:6: note: `relocs_size' was declared here
int relocs_size;
^
In file included from scripts/sortextable.c:192:0:
scripts/sortextable.h:176:3: warning: `relocs_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
memset(relocs, 0, relocs_size);
^
scripts/sortextable.h:106:6: note: `relocs_size' was declared here
int relocs_size;
^
gcc 4.9.1
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Reviewed-by: Jamie Iles <jamie.iles@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Check length of extended attributes and allocation descriptors when
loading inodes from disk. Otherwise corrupted filesystems could confuse
the code and make the kernel oops.
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no> Cc: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The pcc-cpufreq driver is not automatically loaded on systems where
the platform's power management setting requires this driver.
Instead, on those systems no CPU frequency driver is registered and
active.
Make the autoloading matching criteria for loading the pcc-cpufreq
driver the same as done in acpi-cpufreq by commit c655affbd524d01
("ACPI / cpufreq: Add ACPI processor device IDs to acpi-cpufreq").
x86 CPU frequency drivers are now typically autoloaded by specifying
MODULE_DEVICE_TABLE entries and x86cpu model specific matching.
But pcc-cpufreq was omitted when acpi-cpufreq and other drivers were
changed to use this approach.
Both acpi-cpufreq and pcc-cpufreq depend on a distinct and mutually
exclusive set of ACPI methods which are not directly tied to specific
processor model numbers. Both of these drivers have init routines
which look for their required ACPI methods. As a result, only the
appropriate driver registers as the cpu frequency driver and the other
one ends up being unloaded.
Tested on various systems where acpi-cpufreq, intel_pstate, and
pcc-cpufreq are the expected cpu frequency drivers.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by: Joseph Szczypek <joseph.szczypek@hp.com> Reported-by: Trinh Dao <trinh.dao@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.
This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
transfer was finished, this patch doesn't have any side efforts.)
This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Worse yet, reading the error message (the filter again) it says that
there was no error, when there clearly was. The issue is that the
code that checks the input does not check for balanced ops. That is,
having an op between a closed parenthesis and the next token.
This would only cause a warning, and fail out before doing any real
harm, but it should still not caues a warning, and the error reported
should work:
The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.
This fix aligns the buffers inside the struct.
Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com> Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Orphans in the fs tree are cleaned up via open_ctree and subvolume
orphans are cleaned via btrfs_lookup_dentry -- except when a default
subvolume is in use. The name for the default subvolume uses a manual
lookup that doesn't trigger orphan cleanup and needs to trigger it
manually as well. This doesn't apply to the remount case since the
subvolumes are cleaned up by walking the root radix tree.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
fiemap_fill_next_extent returns 0 on success, -errno on error, 1 if this was
the last extent that will fit in user array. If 1 is returned, the return
value may eventually returned to user space, which should not happen, according
to manpage of ioctl.
Signed-off-by: Chengyu Song <csong84@gatech.edu> Reviewed-by: David Sterba <dsterba@suse.cz> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.
Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.
Fix this by initializing the structure in question before the
driver method call.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691
Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This seems an use-after-free problem, and the root cause is
zone->wait_table was not set to *NULL* after free it in
try_offline_node.
When hot re-add a node, we will reuse the pgdat of it, so does the zone
struct, and when add pages to the target zone, it will init the zone
first (including the wait_table) if the zone is not initialized. The
judgement of zone initialized is based on zone->wait_table:
static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}
so if we do not set the zone->wait_table to *NULL* after free it, the
memory hotplug routine will skip the init of new zone when hot re-add
the node, and the wait_table still points to the freed memory, then we
will access the invalid address when trying to wake up the waiting
people after the i/o operation with the page is done, such as mentioned
above.
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / linux-stable / log