A malicious signal handler / restorer can DOS the system by fudging the
user regs saved on stack, causing weird things such as sigreturn returning
to user mode PC but cpu state still being kernel mode....
Ensure that in sigreturn path status32 always has U bit; any other bogosity
(gargbage PC etc) will be taken care of by normal user mode exceptions mechanisms.
Running mtd-utils/tests/ubi-tests/io_basic.c could cause
soft lockup or watchdog reset. It is because *updatevol*
will perform ubi_check_volume() after updating finish
and this function will full scan the updated lebs if the
volume is initialized as STATIC_VOLUME.
This patch adds *cond_resched()* in the loop of lebs scan
to avoid soft lockup.
Helped by Richard Weinberger <richard@nod.at>
[ 2158.067096] INFO: rcu_sched self-detected stall on CPU { 1} (t=2101 jiffies g=1606 c=1605 q=56)
[ 2158.172867] CPU: 1 PID: 2073 Comm: io_basic Tainted: G O 3.10.53 #21
[ 2158.172898] [<c000f624>] (unwind_backtrace+0x0/0x120) from [<c000c294>] (show_stack+0x10/0x14)
[ 2158.172918] [<c000c294>] (show_stack+0x10/0x14) from [<c008ac3c>] (rcu_check_callbacks+0x1c0/0x660)
[ 2158.172936] [<c008ac3c>] (rcu_check_callbacks+0x1c0/0x660) from [<c002b480>] (update_process_times+0x38/0x64)
[ 2158.172953] [<c002b480>] (update_process_times+0x38/0x64) from [<c005ff38>] (tick_sched_handle+0x54/0x60)
[ 2158.172966] [<c005ff38>] (tick_sched_handle+0x54/0x60) from [<c00601ac>] (tick_sched_timer+0x44/0x74)
[ 2158.172978] [<c00601ac>] (tick_sched_timer+0x44/0x74) from [<c003f348>] (__run_hrtimer+0xc8/0x1b8)
[ 2158.172992] [<c003f348>] (__run_hrtimer+0xc8/0x1b8) from [<c003fd9c>] (hrtimer_interrupt+0x128/0x2a4)
[ 2158.173007] [<c003fd9c>] (hrtimer_interrupt+0x128/0x2a4) from [<c0246f1c>] (arch_timer_handler_virt+0x28/0x30)
[ 2158.173022] [<c0246f1c>] (arch_timer_handler_virt+0x28/0x30) from [<c0086214>] (handle_percpu_devid_irq+0x9c/0x124)
[ 2158.173036] [<c0086214>] (handle_percpu_devid_irq+0x9c/0x124) from [<c0082bd8>] (generic_handle_irq+0x20/0x30)
[ 2158.173049] [<c0082bd8>] (generic_handle_irq+0x20/0x30) from [<c000969c>] (handle_IRQ+0x64/0x8c)
[ 2158.173060] [<c000969c>] (handle_IRQ+0x64/0x8c) from [<c0008544>] (gic_handle_irq+0x3c/0x60)
[ 2158.173074] [<c0008544>] (gic_handle_irq+0x3c/0x60) from [<c02f0f80>] (__irq_svc+0x40/0x50)
[ 2158.173083] Exception stack(0xc4043c98 to 0xc4043ce0)
[ 2158.173092] 3c80: c4043ce400000019
[ 2158.173102] 3ca0: 1f8a865fc050ad101f8a864c00000031c04b59700003ebce00000000f3550000
[ 2158.173113] 3cc0: bf00bc68000008000003ebcec4043ce0c0186d14c0186cb880000013ffffffff
[ 2158.173130] [<c02f0f80>] (__irq_svc+0x40/0x50) from [<c0186cb8>] (read_current_timer+0x4/0x38)
[ 2158.173145] [<c0186cb8>] (read_current_timer+0x4/0x38) from [<1f8a865f>] (0x1f8a865f)
[ 2183.927097] BUG: soft lockup - CPU#1 stuck for 22s! [io_basic:2073]
[ 2184.002229] Modules linked in: nandflash(O) [last unloaded: nandflash]
Signed-off-by: Wang Kai <morgan.wang@huawei.com> Signed-off-by: hujianyang <hujianyang@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c2be45f09bb0 ("compal-laptop: Use
devm_hwmon_device_register_with_groups") wanted to change the
registering of hwmon device to resource-managed version. It mostly did
it except the main thing - it forgot to use devm-like function so the
hwmon device leaked after device removal or probe failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: c2be45f09bb0 ("compal-laptop: Use devm_hwmon_device_register_with_groups") Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the lcd type as defined in the Kconfig is not matching in the code.
as a result the rs, rw and en pins were getting interchanged.
Kconfig defines the value of PANEL_LCD to be 1 if we select custom
configuration but in the code LCD_TYPE_CUSTOM is defined as 5.
my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it
as pins of LCD_TYPE_OLD, and it was not working.
Now values are corrected with referenece to the values defined in
Kconfig and it is working.
checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration.
Function-specific setup requests should be handled in such a way, that
apart from filling in the data buffer, the requests are also actually
enqueued: if function-specific setup is called from composte_setup(),
the "usb_ep_queue()" block of code in composite_setup() is skipped.
The printer function lacks this part and it results in e.g. get device id
requests failing: the host expects some response, the device prepares it
but does not equeue it for sending to the host, so the host finally asserts
timeout.
This patch adds enqueueing the prepared responses.
Fixes: 2e87edf49227: "usb: gadget: make g_printer use composite" Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[ported to stable 3.10 and 3.14] Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 3w-sas driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Torsten Luettgert <ml-lkml@enda.eu> Tested-by: Bernd Kardatzki <Bernd.Kardatzki@med.uni-tuebingen.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 3w-9xxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 3w-xxxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org> Reported-by: Shawn Edwards <lesser.evil@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Correct small copy and paste error where autodisable was not being
enabled for the SOC_DAPM_SINGLE_TLV_AUTODISABLE control.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
The mute-LED mode control has the fixed on/off states that are
supposed to remain on/off regardless of the master switch. However,
this doesn't work actually because the vmaster hook is called in the
vmaster code itself.
This patch fixes it by calling the hook indirectly after checking the
mute LED mode.
Looks like audigy emu10k2 (probably emu10k1 - sb live too) support two
modes for DMA. Second mode is useful for 64 bit os with more then 2 GB
of ram (fixes problems with big soundfont loading)
1) 32MB from 2 GB address space using 8192 pages (used now as default)
2) 16MB from 4 GB address space using 4096 pages
Mode is set using HCFG_EXPANDED_MEM flag in HCFG register.
Also format of emu10k2 page table is then different.
Some models provide too long string for the shortname that has 32bytes
including the terminator, and it results in a non-terminated string
exposed to the user-space. This isn't too critical, though, as the
string is stopped at the succeeding longname string.
This patch fixes such entries by dropping "SB" prefix (it's enough to
fit within 32 bytes, so far). Meanwhile, it also changes strcpy()
with strlcpy() to make sure that this kind of problem won't happen in
future, too.
This patch addresses the deadlock by reducing the rance taking
emux->register_mutex in snd_emux_open_seq_oss(). The lock is needed
for the refcount handling, so move it locally. The calls in
emux_seq.c are already with the mutex, thus they are replaced with the
version without mutex lock/unlock.
Basically snd_emux_detach_seq() doesn't need a protection of
emu->register_mutex as it's already being unregistered. So, we can
get rid of this for avoiding the deadlock.
Using the indenting we can see the curly braces were obviously intended.
This is a static checker fix, but my guess is that we don't read enough
bytes, because we don't calculate "t_len" correctly.
Fixes: f1d82698029b ('memstick: use fully asynchronous request processing') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Alex Dubov <oakad@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
time_init invokes timer64_init (which is __init annotation)
since all of these are invoked at init time, lets maintain
consistency by ensuring time_init is marked appropriately
as well.
This fixes the following warning with CONFIG_DEBUG_SECTION_MISMATCH=y
WARNING: vmlinux.o(.text+0x3bfc): Section mismatch in reference from the function time_init() to the function .init.text:timer64_init()
The function time_init() references
the function __init timer64_init().
This is often because time_init lacks a __init
annotation or the annotation of timer64_init is wrong.
Fixes: 546a39546c64 ("C6X: time management") Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For cases where total length of an input SGs is not same as
length of the input data for encryption, omap-aes driver
crashes. This happens in the case when IPsec is trying to use
omap-aes driver.
To avoid this, we copy all the pages from the input SG list
into a contiguous buffer and prepare a single element SG list
for this buffer with length as the total bytes to crypt, which is
similar thing that is done in case of unaligned lengths.
Fixes: 6242332ff2f3 ("crypto: omap-aes - Add support for cases of unaligned lengths") Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e818 ("wl18xx: use new fw stats structures") Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... but in case in future we might use facilities such as LTO, then
OPTIMIZER_HIDE_VAR() is not sufficient to protect gcc from a possible
eviction of the memset(). We have to use a compiler barrier instead.
Minimal test example when we assume memzero_explicit() would *not* be
a call, but would have been *inlined* instead:
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
While debugging an issue with excessive softirq usage, I encountered the
following note in commit 3e339b5dae24a706 ("softirq: Use hotplug thread
infrastructure"):
[ paulmck: Call rcu_note_context_switch() with interrupts enabled. ]
...but despite this note, the patch still calls RCU with IRQs disabled.
This seemingly innocuous change caused a significant regression in softirq
CPU usage on the sending side of a large TCP transfer (~1 GB/s): when
introducing 0.01% packet loss, the softirq usage would jump to around 25%,
spiking as high as 50%. Before the change, the usage would never exceed 5%.
Moving the call to rcu_note_context_switch() after the cond_sched() call,
as it was originally before the hotplug patch, completely eliminated this
problem.
Signed-off-by: Calvin Owens <calvinowens@fb.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Mike Galbraith <mgalbraith@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling unlazy_walk() in walk_component() and do_last() when we find
a symlink that needs to be followed doesn't acquire a reference to vfsmount.
That's fine when the symlink is on the same vfsmount as the parent directory
(which is almost always the case), but it's not always true - one _can_
manage to bind a symlink on top of something. And in such cases we end up
with excessive mntput().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware, according to the specs, is limited to 256 byte transfers,
and current driver has no protections in case users attempt to do larger
transfers. The code will just stomp over status register and mayhem
ensues.
Let's split larger transfers into digestable chunks. Doing this allows
Atmel MXT driver on Pixel 1 function properly (it hasn't since commit 9d8dc3e529a19e427fd379118acd132520935c5d "Input: atmel_mxt_ts -
implement T44 message handling" which tries to consume multiple
touchscreen/touchpad reports in a single transaction).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current -next fails to link an ARM allmodconfig because drivers that use
the core recovery functions can be built as modules but those functions
are not exported:
Fixes: 5f9296ba21b3c (i2c: Add bus recovery infrastructure) Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code decreases from the mss size (which is the gso_size
from the kernel skb) the size of the packet headers.
It shouldn't do that because the mss that comes from the stack
(e.g IPoIB) includes only the tcp payload without the headers.
The result is indication to the HW that each packet that the HW sends
is smaller than what it could be, and too many packets will be sent
for big messages.
An easy way to demonstrate one more aspect of the problem is by
configuring the ipoib mtu to be less than 2*hlen (2*56) and then
run app sending big TCP messages. This will tell the HW to send packets
with giant (negative value which under unsigned arithmetics becomes
a huge positive one) length and the QP moves to SQE state.
In a call to ib_umem_get(), if address is 0x0 and size is
already page aligned, check added in commit 8494057ab5e4
("IB/uverbs: Prevent integer overflow in ib_umem_get address
arithmetic") will refuse to register a memory region that
could otherwise be valid (provided vm.mmap_min_addr sysctl
and mmap_low_allowed SELinux knobs allow userspace to map
something at address 0x0).
This patch allows back such registration: ib_umem_get()
should probably don't care of the base address provided it
can be pinned with get_user_pages().
There's two possible overflows, in (addr + size) and in
PAGE_ALIGN(addr + size), this patch keep ensuring none
of them happen while allowing to pin memory at address
0x0. Anyway, the case of size equal 0 is no more (partially)
handled as 0-length memory region are disallowed by an
earlier check.
If ib_umem_get() is called with a size equal to 0 and an
non-page aligned address, one page will be pinned and a
0-sized umem will be returned to the caller.
This should not be allowed: it's not expected for a memory
region to have a size equal to 0.
This patch adds a check to explicitly refuse to register
a 0-sized region.
The available (i.e. not used) buffers are returned by stk1160_clear_queue(),
on the stop_streaming() path. However, this is insufficient and the current
buffer must be released as well. Fix it.
mvsas is giving a General protection fault when it encounters an expander
attached ATA device. Analysis of mvs_task_prep_ata() shows that the driver is
assuming all ATA devices are locally attached and obtaining the phy mask by
indexing the local phy table (in the HBA structure) with the phy id. Since
expanders have many more phys than the HBA, this is causing the index into the
HBA phy table to overflow and returning rubbish as the pointer.
mvs_task_prep_ssp() instead does the phy mask using the port properties.
Mirror this in mvs_task_prep_ata() to fix the panic.
Reported-by: Adam Talbot <ajtalbot1@gmail.com> Tested-by: Adam Talbot <ajtalbot1@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I suspect this doesn't show up for most anyone because software
algorithms typically don't have a sense of being too busy. However,
when working with the Freescale CAAM driver it will return -EBUSY on
occasion under heavy -- which resulted in dm-crypt deadlock.
After checking the logic in some other drivers, the scheme for
crypt_convert() and it's callback, kcryptd_async_done(), were not
correctly laid out to properly handle -EBUSY or -EINPROGRESS.
Fix this by using the completion for both -EBUSY and -EINPROGRESS. Now
crypt_convert()'s use of completion is comparable to
af_alg_wait_for_completion(). Similarly, kcryptd_async_done() follows
the pattern used in af_alg_complete().
Before this fix dm-crypt would lockup within 1-2 minutes running with
the CAAM driver. Fix was regression tested against software algorithms
on PPC32 and x86_64, and things seem perfectly happy there as well.
Signed-off-by: Ben Collins <ben.c@servergy.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org> Fixes: bcd61c0f535a (clk: qcom: Add support for root clock
generators (RCGs)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com> Cc: Prashant Gaikwad <pgaikwad@nvidia.com> Fixes: 6d5b988e7dc5 ("clk: tegra: implement a reset driver") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.
This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.
While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.
Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.
Changes since v1:
- Change local variable type to bool as well, use boolean values in
code
- Also change prototype of open drain/open source setting functions
since they are only called from _gpiod_set_raw_value()
This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov: 9ece8839b1277fb9128ff6833411614ab6c88d68 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
- don't lock lp->lock in the iss_net_timer for the call of iss_net_poll,
it will lock it itself;
- invert order of lp->lock and opened_lock acquisition in the
iss_net_open to make it consistent with iss_net_poll;
- replace spin_lock with spin_lock_bh when acquiring locks used in
iss_net_timer from non-atomic context;
- replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit
as the driver doesn't use lp->lock in the hard IRQ context;
- replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise
lockdep is unhappy about using non-static key.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xtensa actually uses sync_file_range2 implementation, so it should
define __NR_sync_file_range2 as other architectures that use that
function. That fixes userspace interface (that apparently never worked)
and avoids special-casing xtensa in libc implementations.
See the thread ending at
http://lists.busybox.net/pipermail/uclibc/2015-February/048833.html
for more details.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LCD driver is always built for the XTFPGA platform, but its base address
is not configurable, and is wrong for ML605/KC705. Its initialization
locks up KC705 board hardware.
Make the whole driver optional, and its base address and bus width
configurable. Implement 4-bit bus access method.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_scan_is_offline() may be called under the physical_node_lock
lock of the given device object's parent, so prevent lockdep from
complaining about that by annotating that instance with
SINGLE_DEPTH_NESTING.
Fixes: caa73ea158de (ACPI / hotplug / driver core: Handle containers in a special way) Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported that on a physically 64-bit addressed machine, 32-bit kernel
can trigger crashes in accessing the memory regions that are beyond the
32-bit boundary. The region field's start address should still be 32-bit
compliant, but after a calculation (adding some offsets), it may exceed the
32-bit boundary. This case is rare and buggy, but there are real BIOSes
leaked with such issues (see References below).
This patch fixes this gap by always defining IO addresses as 64-bit, and
allows OSPMs to optimize it for a real 32-bit machine to reduce the size of
the internal objects.
Internal acpi_physical_address usages in the structures that can be fixed
by this change include:
1. struct acpi_object_region:
acpi_physical_address address;
2. struct acpi_address_range:
acpi_physical_address start_address;
acpi_physical_address end_address;
3. struct acpi_mem_space_context;
acpi_physical_address address;
4. struct acpi_table_desc
acpi_physical_address address;
See known issues 1 for other usages.
Note that acpi_io_address which is used for ACPI_PROCESSOR may also suffer
from same problem, so this patch changes it accordingly.
For iasl, it will enforce acpi_physical_address as 32-bit to generate
32-bit OSPM compatible tables on 32-bit platforms, we need to define
ACPI_32BIT_PHYSICAL_ADDRESS for it in acenv.h.
Known issues:
1. Cleanup of mapped virtual address
In struct acpi_mem_space_context, acpi_physical_address is used as a virtual
address:
acpi_physical_address mapped_physical_address;
It is better to introduce acpi_virtual_address or use acpi_size instead.
This patch doesn't make such a change. Because this should be done along
with a change to acpi_os_map_memory()/acpi_os_unmap_memory().
There should be no functional problem to leave this unchanged except
that only this structure is enlarged unexpectedly.
Link: https://github.com/acpica/acpica/commit/aacf863c
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=87971
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=79501 Reported-and-tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Reported-and-tested-by: Sial Nije <sialnije@gmail.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This problem appears to have been introduced in 2.6.29 by commit 93197a36a9c1 "Rewrite sysfs processor cache info code".
This caused lscpu to error out on at least e500v2 devices, eg:
error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory
Some embedded powerpc systems use cache-size in DTS for the unified L2
cache size, not d-cache-size, so we need to allow for both DTS names.
Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle
this.
Fixes: 93197a36a9c1 ("powerpc: Rewrite sysfs processor cache info code") Signed-off-by: Dave Olson <olson@cumulusnetworks.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so
that the device can load the ath3k firmware and re-enumerate itself as an
AR3011 device.
In fd_do_prot_rw(), it allocates prot_buf which is used to copy from
se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf
is also initialized by allocating 'se_cmd->t_prot_nents' entries of
scatterlist and setting the data length of each entry to PAGE_SIZE
at most.
However if se_cmd->t_prot_sg contains a clustered entry (i.e.
sg->length > PAGE_SIZE), the SG table for prot_buf can't be
initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf.
(This actually happened with TCM loopback fabric module)
As prot_buf is allocated by kzalloc() and it's physically contiguous,
we only need a single scatterlist entry.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel
BUG()s are triggered due to the following two issues:
1) prot_sg is not initialized by sg_init_table().
When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a
correct magic value.
2) vmalloc'ed buffer is passed to sg_set_buf().
sg_set_buf() uses virt_to_page() to convert virtual address to struct
page, but it doesn't work with vmalloc address. vmalloc_to_page()
should be used instead. As prot_buf isn't usually too large, so
fix it by allocating prot_buf by kmalloc instead of vmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.
Since commit ee0778a30153
("tools/power: turbostat: make Makefile a bit more capable")
turbostat's Makefile is using
[...]
BUILD_OUTPUT := $(PWD)
[...]
which obviously causes trouble when building "turbostat" with
make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat
because GNU make does not update nor guarantee that $PWD is set.
This patch changes the Makefile to use $CURDIR instead, which GNU make
guarantees to set and update (i.e. when using "make -C ...") and also
adds support for the O= option (see "make help" in your root of your
kernel source tree for more details).
Link: https://bugs.gentoo.org/show_bug.cgi?id=533918 Fixes: ee0778a30153 ("tools/power: turbostat: make Makefile a bit more capable") Signed-off-by: Thomas D. <whissi@whissi.de> Cc: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a event PADDING is hit (a deleted event that is still in the ring
buffer), translate_data() sets the length of the padding and also updates
the data pointer which is passed back to the caller.
This is unneeded because the caller also updates the data pointer with
the passed back length. translate_data() should not update the pointer,
only set the length.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lkml.kernel.org/r/20150324135923.461431960@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously commit 14ece1028b3ed53ffec1b1213ffc6acaf79ad77c added a
support for for syncing parent directory of newly created inodes to
make sure that the inode is not lost after a power failure in
no-journal mode.
However this does not work in majority of cases, namely:
- if the directory has inline data
- if the directory is already indexed
- if the directory already has at least one block and:
- the new entry fits into it
- or we've successfully converted it to indexed
So in those cases we might lose the inode entirely even after fsync in
the no-journal mode. This also includes ext2 default mode obviously.
I've noticed this while running xfstest generic/321 and even though the
test should fail (we need to run fsck after a crash in no-journal mode)
I could not find a newly created entries even when if it was fsynced
before.
Fix this by adjusting the ext4_add_entry() successful exit paths to set
the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the
parent directory as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building a kernel with CPU_BIG_ENDIAN fails if there are stale objects
from a !CPU_BIG_ENDIAN build. Due to a missing FORCE prerequisite on an
if_changed rule in the VDSO Makefile, we attempt to link a stale LE
object into the new BE kernel.
According to Documentation/kbuild/makefiles.txt, FORCE is required for
if_changed rules and forgetting it is a common mistake, so fix it by
'Forcing' the build of vdso. This patch fixes build errors like these:
arch/arm64/kernel/vdso/note.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/note.o
arch/arm64/kernel/vdso/sigreturn.o: compiled for a little endian system and target is big endian
failed to merge target specific data of file arch/arm64/kernel/vdso/sigreturn.o
Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Arun Chandran <achandran@mvista.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: John W. Linville <linville@tuxdriver.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ptrace_resume() is called when the tracee is still __TASK_TRACED. We set
tracee->exit_code and then wake_up_state() changes tracee->state. If the
tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T)
wrongly looks like another report from tracee.
This confuses debugger, and since wait_task_stopped() clears ->exit_code
the tracee can miss a signal.
Note for stable: the bug is very old, but without 9899d11f6544 "ptrace:
ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix
should use lock_task_sighand(child).
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Pavel Labath <labath@google.com> Tested-by: Pavel Labath <labath@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down
address allocation strategy, load_elf_binary() will attempt to map a PIE
binary into an address range immediately below mm->mmap_base.
Unfortunately, load_elf_ binary() does not take account of the need to
allocate sufficient space for the entire binary which means that, while
the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent
PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are
that is supposed to be the "gap" between the stack and the binary.
Since the size of the "gap" on x86_64 is only guaranteed to be 128MB this
means that binaries with large data segments > 128MB can end up mapping
part of their data segment over their stack resulting in corruption of the
stack (and the data segment once the binary starts to run).
Any PIE binary with a data segment > 128MB is vulnerable to this although
address randomization means that the actual gap between the stack and the
end of the binary is normally greater than 128MB. The larger the data
segment of the binary the higher the probability of failure.
Fix this by calculating the total size of the binary in the same way as
load_elf_interp().
Signed-off-by: Michael Davidson <md@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read
acquire the emu_lock before accessing the FPGA. The function used
to access the FPGA (snd_emu1010_fpga_read) also tries to take
the emu_lock which causes a deadlock.
Remove the outer locking in the proc-functions (guarding only the
already safe fpga read) to prevent this deadlock.
[removed superfluous flags variables too -- tiwai]
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every USB Host controller should use this new
macro to define for how long resume signalling
should be driven on the bus.
Currently, almost every single USB controller
is using a 20ms timeout for resume signalling.
That's problematic for two reasons:
a) sometimes that 20ms timer expires a little
before 20ms, which makes us fail certification
b) some (many) devices actually need more than
20ms resume signalling.
Sure, in case of (b) we can state that the device
is against the USB spec, but the fact is that
we have no control over which device the certification
lab will use. We also have no control over which host
they will use. Most likely they'll be using a Windows
PC which, again, we have no control over how that
USB stack is written and how long resume signalling
they are using.
At the end of the day, we must make sure Linux passes
electrical compliance when working as Host or as Device
and currently we don't pass compliance as host because
we're driving resume signallig for exactly 20ms and
that confuses certification test setup resulting in
Certification failure.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The res parameter passed to devm_usb_phy_match() is the location where the
pointer to the usb_phy is stored, hence it needs to be dereferenced before
comparing to the match data in order to find the correct match.
Fixes: 410219dcd2ba ("usb: otg: utils: devres: Add API's to associate a device with the phy") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two PMICs on Cragganmore, currently one dynamically assign
its IRQ base and the other uses a fixed base. It is possible for the
statically assigned PMIC to fail if its IRQ is taken by the dynamically
assigned one. Fix this by statically assigning both the IRQ bases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel
split this is not so, because 2*TASK_SIZE overflows 32 bits,
so the actual value of ELF_ET_DYN_BASE is:
(2 * TASK_SIZE / 3) = 0x2a000000
When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address.
On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000]
for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled
as it fails to map shadow memory.
Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries
has a high chance of loading somewhere in between [0x2a000000 - 0x40000000]
even if ASLR enabled. This makes ASan with PIE absolutely incompatible.
Fix overflow by dividing TASK_SIZE prior to multiplying.
After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y):
(TASK_SIZE / 3 * 2) = 0x7f555554
We have observed a BUG() crash in fs/attr.c:notify_change(). The crash
occurs during an rsync into a filesystem that is exported via NFS.
1.) fs/attr.c:notify_change() modifies the caller's version of attr.
2.) 6de0ec00ba8d ("VFS: make notify_change pass ATTR_KILL_S*ID to
setattr operations") introduced a BUG() restriction such that "no
function will ever call notify_change() with both ATTR_MODE and
ATTR_KILL_S*ID set". Under some circumstances though, it will have
assisted in setting the caller's version of attr to this very
combination.
3.) 27ac0ffeac80 ("locks: break delegations on any attribute
modification") introduced code to handle breaking
delegations. This can result in notify_change() being re-called. attr
_must_ be explicitly reset to avoid triggering the BUG() established
in #2.
4.) The path that that triggers this is via fs/open.c:chmod_common().
The combination of attr flags set here and in the first call to
notify_change() along with a later failed break_deleg_wait()
results in notify_change() being called again via retry_deleg
without resetting attr.
Solution is to move retry_deleg in chmod_common() a bit further up to
ensure attr is completely reset.
There are other places where this seemingly could occur, such as
fs/utimes.c:utimes_common(), but the attr flags are not initially
set in such a way to trigger this.
Fixes: 27ac0ffeac80 ("locks: break delegations on any attribute modification") Reported-by: Eric Meddaugh <etmsys@rit.edu> Tested-by: Eric Meddaugh <etmsys@rit.edu> Signed-off-by: Andrew Elble <aweits@rit.edu> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver forgot to unregister charger power supply if registering of
battery supply failed in probe(). In such case the memory associated
with power supply leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 98a276649358 ("power_supply: Add new lp8788 charger driver") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.
This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: da0a00ebc239 ("power: Add twl4030_madc battery driver.") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has come to my attention that this_cpu_read/write are horrible on
architectures other than x86. Worse yet, they actually disable
preemption or interrupts! This caused some unexpected tracing results
on ARM.
The ring_buffer_lock_reserve has recursion protection that requires
accessing a per cpu variable. But since preempt_disable() is traced, it
too got traced while accessing the variable that is suppose to prevent
recursion like this.
The generic version of this_cpu_read() and write() are:
#define this_cpu_generic_to_op(pcp, val, op) \
do { \
unsigned long flags; \
raw_local_irq_save(flags); \
*__this_cpu_ptr(&(pcp)) op val; \
raw_local_irq_restore(flags); \
} while (0)
Which is unacceptable for locations that know they are within preempt
disabled or interrupt disabled locations.
Paul McKenney stated that __this_cpu_() versions produce much better code on
other architectures than this_cpu_() does, if we know that the call is done in
a preempt disabled location.
I also changed the recursive_unlock() to use two local variables instead
of accessing the per_cpu variable twice.
projects / linux-stable / log