Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.
Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.
The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
If a device quirk modifies the pci_dev->cfg_size to be less than
PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256),
the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE.
Allow sysfs access to config space up to cfg_size, even if the device
doesn't support the entire 4096-byte PCIe config space.
Note that pci_read_config() and pci_write_config() limit access to
dev->cfg_size even though pcie_config_attr contains 4096 (the maximum
size).
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com>
[bhelgaas: more changelog edits] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This patch initialises the fep->netdev pointer. This pointer was not
initialised at all, but is used in fec_enet_timeout_work and in some
error paths.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
seq_read() is a nasty piece of work, not to mention buggy.
It has (I think) an old bug which allows unprivileged userspace to read
beyond the end of m->buf.
I was getting these:
BUG: KASAN: slab-out-of-bounds in seq_read+0xcd2/0x1480 at addr ffff880116889880
Read of size 2713 by task trinity-c2/1329
CPU: 2 PID: 1329 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #96
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
kasan_object_err+0x1c/0x80
kasan_report_error+0x2cb/0x7e0
kasan_report+0x4e/0x80
check_memory_region+0x13e/0x1a0
kasan_check_read+0x11/0x20
seq_read+0xcd2/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
entry_SYSCALL64_slow_path+0x25/0x25
Object at ffff880116889100, in cache kmalloc-4096 size: 4096
Allocated:
PID = 1329
save_stack_trace+0x26/0x80
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
__kmalloc+0x1aa/0x4a0
seq_buf_alloc+0x35/0x40
seq_read+0x7d8/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
return_from_SYSCALL_64+0x0/0x6a
Freed:
PID = 0
(stack is not available)
Memory state around the buggy address: ffff88011688a000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88011688a080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88011688a100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88011688a180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88011688a200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Disabling lock debugging due to kernel taint
This seems to be the same thing that Dave Jones was seeing here:
https://lkml.org/lkml/2016/8/12/334
There are multiple issues here:
1) If we enter the function with a non-empty buffer, there is an attempt
to flush it. But it was not clearing m->from after doing so, which
means that if we try to do this flush twice in a row without any call
to traverse() in between, we are going to be reading from the wrong
place -- the splat above, fixed by this patch.
2) If there's a short write to userspace because of page faults, the
buffer may already contain multiple lines (i.e. pos has advanced by
more than 1), but we don't save the progress that was made so the
next call will output what we've already returned previously. Since
that is a much less serious issue (and I have a headache after
staring at seq_read() for the past 8 hours), I'll leave that for now.
Link: http://lkml.kernel.org/r/1471447270-32093-1-git-send-email-vegard.nossum@oracle.com Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Reported-by: Dave Jones <davej@codemonkey.org.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.
In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.
Clear any pending interrupts after we stop the timer in the probe
function to avoid this.
Cc: stable@vger.kernel.org Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
v4.8-rc3 commit 99f3c90d0d ("dm flakey: error READ bios during the
down_interval") overlooked the 'drop_writes' feature, which is meant to
allow reads to be issued rather than errored, during the down_interval.
Fixes: 99f3c90d0d ("dm flakey: error READ bios during the down_interval") Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
It was reported that hibernation could fail on the 2nd attempt, where the
system hangs at hibernate() -> syscore_resume() -> i8237A_resume() ->
claim_dma_lock(), because the lock has already been taken.
However there is actually no other process would like to grab this lock on
that problematic platform.
Further investigation showed that the problem is triggered by setting
/sys/power/pm_trace to 1 before the 1st hibernation.
Since once pm_trace is enabled, the rtc becomes unmeaningful after suspend,
and meanwhile some BIOSes would like to adjust the 'invalid' RTC (e.g, smaller
than 1970) to the release date of that motherboard during POST stage, thus
after resumed, it may seem that the system had a significant long sleep time
which is a completely meaningless value.
Then in timekeeping_resume -> tk_debug_account_sleep_time, if the bit31 of the
sleep time happened to be set to 1, fls() returns 32 and we add 1 to
sleep_time_bin[32], which causes an out of bounds array access and therefor
memory being overwritten.
As depicted by System.map:
0xffffffff81c9d080 b sleep_time_bin
0xffffffff81c9d100 B dma_spin_lock
the dma_spin_lock.val is set to 1, which caused this problem.
This patch adds a sanity check in tk_debug_account_sleep_time()
to ensure we don't index past the sleep_time_bin array.
[jstultz: Problem diagnosed and original patch by Chen Yu, I've solved the
issue slightly differently, but borrowed his excelent explanation of the
issue here.]
Fixes: 5c83545f24ab "power: Add option to log time spent in suspend" Reported-by: Janek Kozicki <cosurgi@gmail.com> Reported-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: linux-pm@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Xunlei Pang <xpang@redhat.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: stable <stable@vger.kernel.org> Cc: Zhang Rui <rui.zhang@intel.com> Link: http://lkml.kernel.org/r/1471993702-29148-3-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
An assertion in layout_in_gaps() verifies that the gap_lebs pointer is
below the maximum bound. When computing this maximum bound the idx_lebs
count is multiplied by sizeof(int), while C pointers arithmetic does take
into account the size of the pointed elements implicitly already. Remove
the multiplication to fix the assertion.
Fixes: 1e51764a3c2ac05a ("UBIFS: add new flash file system") Cc: <stable@vger.kernel.org> Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com> Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Commit fe6b0dfaba68 ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Reported-by: Alexander Potapenko <glider@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
The commit 4097461897df ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Fixes: 4097461897df ("Input: i8042 - break load dependency ...") Reported-by: Bruno Wolff III <bruno@wolff.to> Tested-by: Bruno Wolff III <bruno@wolff.to> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This bug seems to be present for a very long time.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The UserMode (UM) Linux build was failing in gpiolib-of as it requires
ioremap()/iounmap() to exist, which is absent from UM. The non-existence
of IO memory is negatively defined as CONFIG_NO_IOMEM which means we
need to depend on HAS_IOMEM.
The fifo code in upstream bcache can't use the last element in the buffer,
which was the cause of the bug: if you asked for a power of two size,
it'd give you a fifo that could hold one less than what you asked for
rather than allocating a buffer twice as big.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com> Tested-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
register_cache() is supposed to return an error string on error so that
register_bcache() will will blkdev_put and cleanup other user counters,
but it does not set 'char *err' when cache_alloc() fails (eg, due to
memory pressure) and thus register_bcache() performs no cleanup.
register_bcache() <----------\ <- no jump to err_close, no blkdev_put()
| |
+->register_cache() | <- fails to set char *err
| |
+->cache_alloc() ---/ <- returns error
This patch sets `char *err` for this failure case so that register_cache()
will cause register_bcache() to correctly jump to err_close and do
cleanup. This was tested under OOM conditions that triggered the bug.
Signed-off-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Seems to cause problems for some older hardware. Kudos to Thom Kouwenhoven
for working a lot with the PLLs and figuring this out.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
__replace_page() wronlgy calls mem_cgroup_cancel_charge() in "success" path,
it should only do this if page_check_address() fails.
This means that every enable/disable leads to unbalanced mem_cgroup_uncharge()
from put_page(old_page), it is trivial to underflow the page_counter->count
and trigger OOM.
Reported-and-tested-by: Brenden Blanco <bblanco@plumgrid.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: stable@vger.kernel.org # 3.17+ Fixes: 00501b531c47 ("mm: memcontrol: rewrite charge API") Link: http://lkml.kernel.org/r/20160817153629.GB29724@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+ Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org> Cc: Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org> Cc: Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org> Reported-by: Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When a device is in a status where CIO has killed all I/O by itself the
interrupt for a clear request may not contain an irb to determine the
clear function. Instead it contains an error pointer -EIO.
This was ignored by the DASD int_handler leading to a hanging device
waiting for a clear interrupt.
Handle -EIO error pointer correctly for requests that are clear pending and
treat the clear as successful.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef9775 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
Since 6de62f15b581 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method. However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.
Fix this by removing the setkey method from the non-keyed hash
algorithms.
Fixes: 6de62f15b581 ("crypto: algif_hash - Require setkey before accept(2)") Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)' Cc: stable@vger.kernel.org Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
udriver struct allocated by kzalloc() will not be freed
if usb_register() and next calls fail. This patch fixes this
by adding one more step with kfree(udriver) in error path.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee34 ("tcp: implement RFC 5961 3.2") Reported-by: Yue Cao <ycao009@ucr.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Use set_posix_acl, which includes proper permission checks, instead of
calling ->set_acl directly. Without this anyone may be able to grant
themselves permissions to a file by setting the ACL.
Lock the inode to make the new checks atomic with respect to set_acl.
(Also, nfsd was the only caller of set_acl not locking the inode, so I
suspect this may fix other races.)
This also simplifies the code, and ensures our ACLs are checked by
posix_acl_valid.
The permission checks and the inode locking were lost with commit 4ac7249e, which changed nfsd to use the set_acl inode operation directly
instead of going through xattr handlers.
Reported-by: David Sinquin <david@sinquin.eu>
[agreunba@redhat.com: use set_posix_acl] Fixes: 4ac7249e Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Factor out part of posix_acl_xattr_set into a common function that takes
a posix_acl, which nfsd can also call.
The prototype already exists in include/linux/posix_acl.h.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: stable@vger.kernel.org Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In commit 8445a87f7092 "powerpc/iommu: Remove the dependency on EEH
struct in DDW mechanism", the PE address was replaced with the PCI
config address in order to remove dependency on EEH. According to PAPR
spec, firmware (pHyp or QEMU) should accept "xxBBSSxx" format PCI config
address, not "xxxxBBSS" provided by the patch. Note that "BB" is PCI bus
number and "SS" is the combination of slot and function number.
This fixes the PCI address passed to DDW RTAS calls.
Fixes: 8445a87f7092 ("powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism") Cc: stable@vger.kernel.org # v3.4+ Reported-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Commit 39baadbf36ce ("powerpc/eeh: Remove eeh information from pci_dn")
changed the pci_dn struct by removing its EEH-related members.
As part of this clean-up, DDW mechanism was modified to read the device
configuration address from eeh_dev struct.
As a consequence, now if we disable EEH mechanism on kernel command-line
for example, the DDW mechanism will fail, generating a kernel oops by
dereferencing a NULL pointer (which turns to be the eeh_dev pointer).
This patch just changes the configuration address calculation on DDW
functions to a manual calculation based on pci_dn members instead of
using eeh_dev-based address.
No functional changes were made. This was tested on pSeries, both
in PHyp and qemu guest.
Fixes: 39baadbf36ce ("powerpc/eeh: Remove eeh information from pci_dn") Cc: stable@vger.kernel.org # v3.4+ Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This problem can occur in the following situation:
open()
- pread()
- .seq_start()
- iter = kmalloc() // succeeds
- seqf->private = iter
- .seq_stop()
- kfree(seqf->private)
- pread()
- .seq_start()
- iter = kmalloc() // fails
- .seq_stop()
- class_dev_iter_exit(seqf->private) // boom! old pointer
As the comment in disk_seqf_stop() says, stop is called even if start
failed, so we need to reinitialise the private pointer to NULL when seq
iteration stops.
An alternative would be to set the private pointer to NULL when the
kmalloc() in disk_seqf_start() fails.
The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:
Error: failed to assemble instruction: "CMP A0.2,D0Ar6"
Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).
The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.
Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.
Commit 53dad6d3a8e5 ("ipc: fix race with LSMs") updated ipc_rcu_putref()
to receive rcu freeing function but used generic ipc_rcu_free() instead
of msg_rcu_free() which does security cleaning.
Running LTP msgsnd06 with kmemleak gives the following:
In powerpc servers with large memory(32TB), we watched several soft
lockups for hugepage under stress tests.
The call traces are as follows:
1.
get_page_from_freelist+0x2d8/0xd50
__alloc_pages_nodemask+0x180/0xc20
alloc_fresh_huge_page+0xb0/0x190
set_max_huge_pages+0x164/0x3b0
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
glibc recently did a sync up (94e73c95d9b5 "elf.h: Sync with the gabi
webpage") that added a #define for EM_METAG but did not add relocations
This triggers build errors:
scripts/recordmcount.c: In function 'do_file':
scripts/recordmcount.c:466:28: error: 'R_METAG_ADDR32' undeclared (first use in this function)
case EM_METAG: reltype = R_METAG_ADDR32;
^~~~~~~~~~~~~~
scripts/recordmcount.c:466:28: note: each undeclared identifier is reported only once for each function it appears in
scripts/recordmcount.c:468:20: error: 'R_METAG_NONE' undeclared (first use in this function)
rel_type_nop = R_METAG_NONE;
^~~~~~~~~~~~
Work around this change with some more #ifdefery for the relocations.
The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.
So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.
Cc: stable@vger.kernel.org Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de> Tested-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: David Howells <dhowells@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keyrings@vger.kernel.org Cc: linux-security-module@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This laptop needs GPIO4 pulled high to enable the headphone amplifier,
and has a mute LED on GPIO3. I modelled the patch on the existing
GPIO4 code which pulls the line low for the same purpose; this time,
the HP amp line is pulled high.
v2: Disable the headphone amplifier when no headphone is connected.
Don't disable power savings to preserve the LED state.
v3: Remove headset-specific hooks and code; this is just a headphone.
The patch f045f459d925 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the
display when using fonts with width that is not divisiable by 8.
The monochrome bitmap for each character is stored in memory by lines from top
to bottom. Each line is padded to a full byte.
For example, for 22x11 font, each line is padded to 16 bits, so each
character is consuming 44 bytes total, that is 11 32-bit words. The patch f045f459d925 changed the logic to "dsize = ALIGN(image->width *
image->height, 32) >> 5", that is just 8 words - this is incorrect and it
causes display corruption.
This patch adds the necesary padding of lines to 8 bytes.
This patch should be backported to stable kernels where f045f459d925 was
backported.
When the volume resize operation shrinks a volume,
LEBs will be unmapped. Since unmapping will not erase these
LEBs immediately we have to wait for that operation to finish.
Otherwise in case of a power cut right after writing the new
volume table the UBI attach process can find more LEBs than the
volume table knows. This will render the UBI image unattachable.
Fix this issue by waiting for erase to complete and write the new
volume table afterward.
Cc: <stable@vger.kernel.org> Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
fuse_flush() calls write_inode_now() that triggers writeback, but actual
writeback will happen later, on fuse_sync_writes(). If an error happens,
fuse_writepage_end() will set error bit in mapping->flags. So, we have to
check mapping->flags after fuse_sync_writes().
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
MIPS64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl. The latter will work in a lot of cases, thereby hiding
the issue.
It turns out that if the guest does a H_CEDE while the CPU is in
a transactional state, and the H_CEDE does a nap, and the nap
loses the architected state of the CPU (which is is allowed to do),
then we lose the checkpointed state of the virtual CPU. In addition,
the transactional-memory state recorded in the MSR gets reset back
to non-transactional, and when we try to return to the guest, we take
a TM bad thing type of program interrupt because we are trying to
transition from non-transactional to transactional with a hrfid
instruction, which is not permitted.
The result of the program interrupt occurring at that point is that
the host CPU will hang in an infinite loop with interrupts disabled.
Thus this is a denial of service vulnerability in the host which can
be triggered by any guest (and depending on the guest kernel, it can
potentially triggered by unprivileged userspace in the guest).
This vulnerability has been assigned the ID CVE-2016-5412.
To fix this, we save the TM state before napping and restore it
on exit from the nap, when handling a H_CEDE in real mode. The
case where H_CEDE exits to host virtual mode is already OK (as are
other hcalls which exit to host virtual mode) because the exit
path saves the TM state.
This moves the transactional memory state save and restore sequences
out of the guest entry/exit paths into separate procedures. This is
so that these sequences can be used in going into and out of nap
in a subsequent patch.
The only code changes here are (a) saving and restore LR on the
stack, since these new procedures get called with a bl instruction,
(b) explicitly saving r1 into the PACA instead of assuming that
HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary
and redundant setting of MSR[TM] that should have been removed by
commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory
support", 2013-09-24) but wasn't.
During following a symbolic link we received err_buf from SMB2_open().
While the validity of SMB2 error response is checked previously
in smb2_check_message() a symbolic link payload is not checked at all.
Fix it by adding such checks.
Cc: Dan Carpenter <dan.carpenter@oracle.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
if, when mounting //HOST/share/sub/dir/foo we can query /sub/dir/foo but
not any of the path components above:
- store the /sub/dir/foo prefix in the cifs super_block info
- in the superblock, set root dentry to the subpath dentry (instead of
the share root)
- set a flag in the superblock to remember it
- use prefixpath when building path from a dentry
fixes bso#8950
Signed-off-by: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org> Tested-by: Mark Laws <mdl@60hz.org> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. If a module signing key is used for
multiple ABI-incompatible kernels, the modules need to include enough
version information to distinguish them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. Loading a signed module meant for a
kernel with a different ABI could have interesting effects.
Therefore, treat all signatures as invalid when a module is
force-loaded.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The problem is that irda_open_tsap() can fail and leave self->tsap = NULL,
and then irttp_connect_request() almost immediately dereferences it.
Cc: stable@vger.kernel.org Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
NFS doesn't expect requests with wb_bytes set to zero and may make
unexpected decisions about how to handle that request at the page IO layer.
Skip request creation if we won't have any wb_bytes in the request.
The commit d56d6b3d7d69 ("gpio: langwell: add Intel Merrifield support")
doesn't look at all as a proper support for Intel Merrifield and I dare to say
that it distorts the behaviour of the hardware.
The register map is different on Intel Merrifield, i.e. only 6 out of 8
register have the same purpose but none of them has same location in the
address space. The current case potentially harmful to existing hardware since
it's poking registers on wrong offsets and may set some pin to be GPIO output
when connected hardware doesn't expect such.
Besides the above GPIO and pinctrl on Intel Merrifield have been located in
different IP blocks. The functionality has been extended as well, i.e. added
support of level interrupts, special registers for wake capable sources and
thus, in my opinion, requires a completele separate driver.
If someone wondering the existing gpio-intel-mid.c would be converted to actual
pinctrl (which by the fact it is now), though I wouldn't be a volunteer to do
that.
There is a double fetch problem in audit_log_single_execve_arg()
where we first check the execve(2) argumnets for any "bad" characters
which would require hex encoding and then re-fetch the arguments for
logging in the audit record[1]. Of course this leaves a window of
opportunity for an unsavory application to munge with the data.
This patch reworks things by only fetching the argument data once[2]
into a buffer where it is scanned and logged into the audit
records(s). In addition to fixing the double fetch, this patch
improves on the original code in a few other ways: better handling
of large arguments which require encoding, stricter record length
checking, and some performance improvements (completely unverified,
but we got rid of some strlen() calls, that's got to be a good
thing).
As part of the development of this patch, I've also created a basic
regression test for the audit-testsuite, the test can be tracked on
GitHub at the following link:
[1] If you pay careful attention, there is actually a triple fetch
problem due to a strnlen_user() call at the top of the function.
[2] This is a tiny white lie, we do make a call to strnlen_user()
prior to fetching the argument data. I don't like it, but due to the
way the audit record is structured we really have no choice unless we
copy the entire argument at once (which would require a rather
wasteful allocation). The good news is that with this patch the
kernel no longer relies on this strnlen_user() value for anything
beyond recording it in the log, we also update it with a trustworthy
value whenever possible.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The "fix" in commit 0b08c5e5944 ("audit: Fix check of return value of
strnlen_user()") didn't fix anything, it broke things. As reported by
Steven Rostedt:
"Yes, strnlen_user() returns 0 on fault, but if you look at what len is
set to, than you would notice that on fault len would be -1"
because we just subtracted one from the return value. So testing
against 0 doesn't test for a fault condition, it tests against a
perfectly valid empty string.
Also fix up the usual braindamage wrt using WARN_ON() inside a
conditional - make it part of the conditional and remove the explicit
unlikely() (which is already part of the WARN_ON*() logic, exactly so
that you don't have to write unreadable code.
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org> Cc: Jan Kara <jack@suse.cz> Cc: Paul Moore <pmoore@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
strnlen_user() returns 0 when it hits fault, not -1. Fix the test in
audit_log_single_execve_arg(). Luckily this shouldn't ever happen unless
there's a kernel bug so it's mostly a cosmetic fix.
CC: Paul Moore <pmoore@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The secmech hmac(md5) structures are present in the TCP_Server_Info
struct and can be shared among multiple CIFS sessions. However, the
server mutex is not currently held when these structures are allocated
and used, which can lead to a kernel crashes, as in the scenario below:
Fix this by locking the srv_mutex around the code which uses these
hmac(md5) structures. All the other secmech algos already have similar
locking.
Fixes: 95dc8dd14e2e84cc ("Limit allocation of crypto mechanisms to dialect which requires") Signed-off-by: Rabin Vincent <rabinv@axis.com> Acked-by: Sachin Prabhu <sprabhu@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.
This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.
To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.
Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.
Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # 3.14+ Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().
However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().
This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.
To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.
Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # 3.14+ Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b96078f, but moved
around in commit 66507c7bc8895 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Cc: stable@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When we retrieve imtu value from userspace we should use 16 bit pointer
cast instead of 32 as it's defined that way in headers. Fixes setsockopt
calls on big-endian platforms.
At the start of __tm_recheckpoint() we save the kernel stack pointer
(r1) in SPRG SCRATCH0 (SPRG2) so that we can restore it after the
trecheckpoint.
Unfortunately, the same SPRG is used in the SLB miss handler. If an
SLB miss is taken between the save and restore of r1 to the SPRG, the
SPRG is changed and hence r1 is also corrupted. We can end up with
the following crash when we start using r1 again after the restore
from the SPRG:
projects / linux-stable / log