According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
There appears to be no formal statement of what pv_irq_ops.save_fl() is
supposed to return precisely. Native returns the full flags, while lguest and
Xen only return the Interrupt Flag, and both have comments by the
implementations stating that only the Interrupt Flag is looked at. This may
have been true when initially implemented, but no longer is.
To make matters worse, the Xen PVOP leaves the upper bits undefined, making
the BUG_ON() undefined behaviour. Experimentally, this now trips for 32bit PV
guests on Broadwell hardware. The BUG_ON() is consistent for an individual
build, but not consistent for all builds. It has also been a sitting timebomb
since SMAP support was introduced.
Use native_save_fl() instead, which will obtain an accurate view of the AC
flag.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Tested-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: <lguest@lists.ozlabs.org> Cc: Xen-devel <xen-devel@lists.xen.org> CC: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1433323874-6927-1-git-send-email-andrew.cooper3@citrix.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This is an ancient bug that was actually attempted to be fixed once
(badly) by me eleven years ago in commit 4ceb5db9757a ("Fix
get_user_pages() race for write access") but that was then undone due to
problems on s390 by commit f33ea7f404e5 ("fix get_user_pages bug").
In the meantime, the s390 situation has long been fixed, and we can now
fix it by checking the pte_dirty() bit properly (and do it better). The
s390 dirty bit was implemented in abf09bed3cce ("s390/mm: implement
software dirty bits") which made it into v3.9. Earlier kernels will
have to look at the page state itself.
Also, the VM has become more scalable, and what used a purely
theoretical race back then has become easier to trigger.
To fix it, we introduce a new internal FOLL_COW flag to mark the "yes,
we already did a COW" rather than play racy games with FOLL_WRITE that
is very fundamental, and then use the pte dirty flag to validate that
the FOLL_COW flag is still valid.
Since commit acb2505d0119 ("openrisc: fix copy_from_user()"),
copy_from_user() returns the number of bytes requested, not the
number of bytes not copied.
The commit "genirq: Generic chip: Change irq_reg_{readl,writel}
arguments" modified the API. In the same tome the
arch/arm/plat-orion/gpio.c file received a fix with the use of the old
API: "ARM: orion: Fix for certain sequence of request_irq can cause
irq storm". This commit fixes the use of the API.
arch/avr32/kernel/built-in.o: In function `arch_ptrace':
(.text+0x650): undefined reference to `___copy_from_user'
arch/avr32/kernel/built-in.o:(___ksymtab+___copy_from_user+0x0): undefined
reference to `___copy_from_user'
kernel/built-in.o: In function `proc_doulongvec_ms_jiffies_minmax':
(.text+0x5dd8): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `proc_dointvec_minmax_sysadmin':
sysctl.c:(.text+0x6174): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `ptrace_has_cap':
ptrace.c:(.text+0x69c0): undefined reference to `___copy_from_user'
kernel/built-in.o:ptrace.c:(.text+0x6b90): more undefined references to
`___copy_from_user' follow
hexagon:defconfig fails to build in linux-next since commit 332fd7c4fef5
("genirq: Generic chip: Change irq_reg_{readl,writel} arguments").
The primary build failure is
arch/hexagon/include/asm/cacheflush.h: In function 'copy_to_user_page':
arch/hexagon/include/asm/cacheflush.h:89:22: error: 'VM_EXEC' undeclared
This is the result of including of <linux/io.h> from <linux/irq.h>,
which is now necessary due to the use of readl and writel from irq.h.
This causes recursive inclusions in hexagon code; cacheflush.h is included
from mm.h prior to the definition of VM_EXEC.
Fix the problem by moving copy_to_user_page from the hexagon include file to
arch/hexagon/mm/cache.c, similar to other architectures. After this change,
several redefinitions of readl and writel are reported. Those are caused
by recursive inclusions of io.h and asm/cacheflush.h. Fix those problems by
reducing the number of files included from those files. Also, it was necessary
to stop including asm-generic/cacheflush.h from asm/cacheflush.h. Instead,
functionality originally provided by asm-generic/cacheflush.h is now coded
in asm/cacheflush.h directly.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
signed-off-by: Richard Kuo <rkuo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
block: Do a full clone when splitting discard bios
This fixes a data corruption bug when using discard on top of MD linear,
raid0 and raid10 personalities.
Commit 20d0189b1012 "block: Introduce new bio_split()" permits sharing
the bio_vec between the two resulting bios. That is fine for read/write
requests where the bio_vec is immutable. For discards, however, we need
to be able to attach a payload and update the bio_vec so the page can
get mapped to a scatterlist entry. Therefore the bio_vec can not be
shared when splitting discards and we must do a full clone.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reported-by: Seunguk Shin <seunguk.shin@samsung.com> Tested-by: Seunguk Shin <seunguk.shin@samsung.com> Cc: Seunguk Shin <seunguk.shin@samsung.com> Cc: Jens Axboe <axboe@fb.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: <stable@vger.kernel.org> # v3.14+ Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Cc: stable@vger.kernel.org # v3.5+ Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
If we punch a hole on a reflink such that following conditions are met:
1. start offset is on a cluster boundary
2. end offset is not on a cluster boundary
3. (end offset is somewhere in another extent) or
(hole range > MAX_CONTIG_BYTES(1MB)),
we dont COW the first cluster starting at the start offset. But in this
case, we were wrongly passing this cluster to
ocfs2_zero_range_for_truncate() to zero out. This will modify the
cluster in place and zero it in the source too.
Fix this by skipping this cluster in such a scenario.
To reproduce:
1. Create a random file of say 10 MB
xfs_io -c 'pwrite -b 4k 0 10M' -f 10MBfile
2. Reflink it
reflink -f 10MBfile reflnktest
3. Punch a hole at starting at cluster boundary with range greater that
1MB. You can also use a range that will put the end offset in another
extent.
fallocate -p -o 0 -l 1048615 reflnktest
4. sync
5. Check the first cluster in the source file. (It will be zeroed out).
dd if=10MBfile iflag=direct bs=<cluster size> count=1 | hexdump -C
Link: http://lkml.kernel.org/r/1470957147-14185-1-git-send-email-ashish.samant@oracle.com Signed-off-by: Ashish Samant <ashish.samant@oracle.com> Reported-by: Saar Maoz <saar.maoz@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Eric Ren <zren@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
fanotify_get_response() calls fsnotify_remove_event() when it finds that
group is being released from fanotify_release() (bypass_perm is set).
However the event it removes need not be only in the group's notification
queue but it can have already moved to access_list (userspace read the
event before closing the fanotify instance fd) which is protected by a
different lock. Thus when fsnotify_remove_event() races with
fanotify_release() operating on access_list, the list can get corrupted.
Fix the problem by moving all the logic removing permission events from
the lists to one place - fanotify_release().
Somewhere along the way the autofs expire operation has changed to hold
a spin lock over expired dentry selection. The autofs indirect mount
expired dentry selection is complicated and quite lengthy so it isn't
appropriate to hold a spin lock over the operation.
Commit 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") added a
might_sleep() to dput() causing a WARN_ONCE() about this usage to be
issued.
But the spin lock doesn't need to be held over this check, the autofs
dentry info. flags are enough to block walks into dentrys during the
expire.
I've left the direct mount expire as it is (for now) because it is much
simpler and quicker than the indirect mount expire and adding spin lock
release and re-aquires would do nothing more than add overhead.
Fixes: 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") Link: http://lkml.kernel.org/r/20160912014017.1773.73060.stgit@pluto.themaw.net Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: Takashi Iwai <tiwai@suse.de> Cc: NeilBrown <neilb@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
* make autofs4_expire_indirect() skip the dentries being in process of
expiry
* do *not* mess with list_move(); making sure that dentry with
AUTOFS_INF_EXPIRING are not picked for expiry is enough.
* do not remove NO_RCU when we set EXPIRING, don't bother with smp_mb()
there. Clear it at the same time we clear EXPIRING. Makes a bunch of
tests simpler.
* rename NO_RCU to WANT_EXPIRE, which is what it really is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Commit ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery")
checks if lockres master has changed to identify whether new master has
finished recovery or not. This will introduce a race that right after
old master does umount ( means master will change), a new convert
request comes.
In this case, it will reset lockres state to DLM_RECOVERING and then
retry convert, and then fail with lockres->l_action being set to
OCFS2_AST_INVALID, which will cause inconsistent lock level between
ocfs2 and dlm, and then finally BUG.
Since dlm recovery will clear lock->convert_pending in
dlm_move_lockres_to_recovery_list, we can use it to correctly identify
the race case between convert and recovery. So fix it.
Fixes: ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery") Link: http://lkml.kernel.org/r/57CE1569.8010704@huawei.com Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
get_user_ex(x, ptr) should zero x on failure. It's not a lot of a leak
(at most we are leaking uninitialized 64bit value off the kernel stack,
and in a fairly constrained situation, at that), but the fix is trivial,
so...
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ This sat in different branch from the uaccess fixes since mid-August ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
really ugly, but apparently avr32 compilers turns access_ok() into
something so bad that they want it in assembler. Left that way,
zeroing added in inline wrapper.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: stable@vger.kernel.org Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
It could be done in exception-handling bits in __get_user_b() et.al.,
but the surgery involved would take more knowledge of sh64 details
than I have or _want_ to have.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
It's -EFAULT, not -1 (and contrary to the comment in there,
__strnlen_user() can return 0 - on faults).
Cc: stable@vger.kernel.org Acked-by: Richard Kuo <rkuo@codeaurora.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Cc: stable@vger.kernel.org Fixes: 9a774c78e211 ("cfg80211: Support multiple CSA counters") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Pass in the irq_chip_generic struct so we can use different readl/writel
settings for each irqchip driver, when appropriate. Compute
(gc->reg_base + reg_offset) in the helper function because this is pretty
much what all callers want to do anyway.
Compile-tested using the following configurations:
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a128 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions") Cc: stable@vger.kernel.org Reported-by: xiakaixu <xiakaixu@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: <stable@vger.kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via
mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when
the userspace buffer gets unmapped. However, when the Hypervisor
process exits without explicit unmap of the guest buffers, the only
notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release
) which does nothing on arm. Later this causes us to access pages that
were already released [via exit_mmap() -> unmap_vmas()] when we actually
get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() ->
kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC,
which unmaps any free'd pages from the linear map.
Although a similar issue was spotted and a fix patch was merged in
commit [6b760bb2c63a: ALSA: timer: fix division by zero after
SNDRV_TIMER_IOCTL_CONTINUE], it seems covering only a part of
iceberg.
In this patch, we fix the issue a bit more drastically. Basically the
continue of an uninitialized timer is supposed to be a fresh start, so
we do it for user timers. For the direct snd_timer_continue() call,
there is no way to pass the initial tick value, so we kick out for the
uninitialized case.
snd_timer_notify1() is called outside the spinlock and it retakes the
lock after the unlock. This is rather racy, and it's safer to move
snd_timer_notify() call inside the main spinlock.
The patch also contains a slight refactoring / cleanup of the code.
Now all start/stop/continue/pause look more symmetric and a bit better
readable.
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
In commit c60ac5693c47 ("powerpc: Update kernel VSID range", 2013-03-13)
we lost a check on the region number (the top four bits of the effective
address) for addresses below PAGE_OFFSET. That commit replaced a check
that the top 18 bits were all zero with a check that bits 46 - 59 were
zero (performed for all addresses, not just user addresses).
This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx
and we will insert a valid SLB entry for it. The VSID used will be the
same as if the top 4 bits were 0, but the page size will be some random
value obtained by indexing beyond the end of the mm_ctx_high_slices_psize
array in the paca. If that page size is the same as would be used for
region 0, then userspace just has an alias of the region 0 space. If the
page size is different, then no HPTE will be found for the access, and
the process will get a SIGSEGV (since hash_page_mm() will refuse to create
a HPTE for the bogus address).
The access beyond the end of the mm_ctx_high_slices_psize can be at most
5.5MB past the array, and so will be in RAM somewhere. Since the access
is a load performed in real mode, it won't fault or crash the kernel.
At most this bug could perhaps leak a little bit of information about
blocks of 32 bytes of memory located at offsets of i * 512kB past the
paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11.
When calling .import() on a cryptd ahash_request, the structure members
that describe the child transform in the shash_desc need to be initialized
like they are when calling .init()
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org Fixes: c15b1ccadb32 ("ipv6: move DAD and addrconf_verify processing
to workqueue") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
We use a btrfs_log_ctx structure to pass information into the
tree log commit, and get error values out. It gets added to a per
log-transaction list which we walk when things go bad.
Commit d1433debe added an optimization to skip waiting for the log
commit, but didn't take root_log_ctx out of the list. This
patch makes sure we remove things before exiting.
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
The origin of the issue I've seen is related to
a missing memory barrier between check for task->state and
the check for task->on_rq.
The task being woken up is already awake from a schedule()
and is doing the following:
do {
schedule()
set_current_state(TASK_(UN)INTERRUPTIBLE);
} while (!cond);
The waker, actually gets stuck doing the following in
try_to_wake_up():
while (p->on_cpu)
cpu_relax();
Analysis:
The instance I've seen involves the following race:
CPU1 CPU2
while () {
if (cond)
break;
do {
schedule();
set_current_state(TASK_UN..)
} while (!cond);
wakeup_routine()
spin_lock_irqsave(wait_lock)
raw_spin_lock_irqsave(wait_lock) wake_up_process()
} try_to_wake_up()
set_current_state(TASK_RUNNING); ..
list_del(&waiter.list);
CPU2 wakes up CPU1, but before it can get the wait_lock and set
current state to TASK_RUNNING the following occurs:
CPU3
wakeup_routine()
raw_spin_lock_irqsave(wait_lock)
if (!list_empty)
wake_up_process()
try_to_wake_up()
raw_spin_lock_irqsave(p->pi_lock)
..
if (p->on_rq && ttwu_wakeup())
..
while (p->on_cpu)
cpu_relax()
..
CPU3 tries to wake up the task on CPU1 again since it finds
it on the wait_queue, CPU1 is spinning on wait_lock, but immediately
after CPU2, CPU3 got it.
CPU3 checks the state of p on CPU1, it is TASK_UNINTERRUPTIBLE and
the task is spinning on the wait_lock. Interestingly since p->on_rq
is checked under pi_lock, I've noticed that try_to_wake_up() finds
p->on_rq to be 0. This was the most confusing bit of the analysis,
but p->on_rq is changed under runqueue lock, rq_lock, the p->on_rq
check is not reliable without this fix IMHO. The race is visible
(based on the analysis) only when ttwu_queue() does a remote wakeup
via ttwu_queue_remote. In which case the p->on_rq change is not
done uder the pi_lock.
The result is that after a while the entire system locks up on
the raw_spin_irqlock_save(wait_lock) and the holder spins infintely
Reproduction of the issue:
The issue can be reproduced after a long run on my system with 80
threads and having to tweak available memory to very low and running
memory stress-ng mmapfork test. It usually takes a long time to
reproduce. I am trying to work on a test case that can reproduce
the issue faster, but thats work in progress. I am still testing the
changes on my still in a loop and the tests seem OK thus far.
Big thanks to Benjamin and Nick for helping debug this as well.
Ben helped catch the missing barrier, Nick caught every missing
bit in my theory.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[ Updated comment to clarify matching barriers. Many
architectures do not have a full barrier in switch_to()
so that cannot be relied upon. ] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alexey Kardashevskiy <aik@ozlabs.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nicholas Piggin <nicholas.piggin@gmail.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/e02cce7b-d9ca-1ad0-7a61-ea97c7582b37@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
In hwdep interface of fireworks driver, accessing to user space is in a
critical section with disabled local interrupt. Depending on architecture,
accessing to user space can cause page fault exception. Then local
processor stores machine status and handles the synchronous event. A
handler corresponding to the event can call task scheduler to wait for
preparing pages. In a case of usage of single core processor, the state to
disable local interrupt is worse because it don't handle usual interrupts
from hardware.
This commit fixes this bug, performing the accessing outside spinlock. This
commit also gives up counting the number of queued response messages to
simplify ring-buffer management.
i.MX6SX has bypass PMIC ready function, as this function
is normally NOT enabled on the board design, so we need
to bypass the PMIC ready pin check during DSM mode resume
flow, otherwise, the internal DSM resume logic will be
waiting for this signal to be ready forever and cause
resume fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Fixes: ff843d621bfc ("ARM: imx: add suspend support for i.mx6sx") Cc: <stable@vger.kernel.org> Tested-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Avoid getting sample rate on B850V3 CP2114 as it is unsupported and
causes noisy "current rate is different from the runtime rate" messages
when playback starts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw> Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The problem happens when you call ioctl(SNDRV_TIMER_IOCTL_CONTINUE) on a
completely new/unused timer -- it will have ->sticks == 0, which causes a
divide by 0 in snd_hrtimer_callback().
Commit 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment
partition") split the "u-boot" partition into "u-boot" and "u-boot
environment". However, instead of the size of the environment, an offset
was given, resulting in overlapping partitions.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Fixes: 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment partition") Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Luka Perkov <luka@openwrt.org> Cc: stable@vger.kernel.org # 3.13+ Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The code setting XP watchpoint comparator and mask registers should, in
order to be fully compliant with specification, zero one or more most
significant bits of each field. In both L cases it means zeroing bit 63.
The bitmask doing this was wrong, though, zeroing bit 60 instead.
Fortunately, due to a lucky coincidence, this turned out to be fairly
innocent with the existing hardware.
Fuzzing the CCN perf driver revealed a small but definitely dangerous
mistake in the event setup code. When a cycle counter is requested, the
driver should not reconfigure the events bus at all, otherwise it will
corrupt (in most but the simplest cases) its configuration and may end
up accessing XP array out of its bounds and corrupting control
registers.
Reported-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Cc: stable@vger.kernel.org # 3.17+ Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Ben Hutchings pointed out that the commit isn't safe since it assumes
that the structure used by the driver is iw_point, when in fact there's
no way to know about that.
Fortunately, the only driver in the tree that ever runs this code path
is the wilc1000 staging driver, so it doesn't really matter.
Clearly I should have investigated this better before applying, sorry.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable@vger.kernel.org [though I guess it doesn't matter much] Fixes: 3d5fdff46c4b ("wext: Fix 32 bit iwpriv compatibility issue with 64 bit Kernel") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Fix by allowing EOPNOTSUPP as a valid return value from
vfs_removexattr(XATTR_NAME_POSIX_ACL_*). Upper filesystem may not support
ACL and still be perfectly able to support overlayfs.
When mapping a page into the guest we error check using is_error_pfn(),
however this doesn't detect a value of KVM_PFN_NOSLOT, indicating an
error HVA for the page. This can only happen on MIPS right now due to
unusual memslot management (e.g. being moved / removed / resized), or
with an Enhanced Virtual Memory (EVA) configuration where the default
KVM_HVA_ERR_* and kvm_is_error_hva() definitions are unsuitable (fixed
in a later patch). This case will be treated as a pfn of zero, mapping
the first page of physical memory into the guest.
It would appear the MIPS KVM port wasn't updated prior to being merged
(in v3.10) to take commit 81c52c56e2b4 ("KVM: do not treat noslot pfn as
a error pfn") into account (merged v3.8), which converted a bunch of
is_error_pfn() calls to is_error_noslot_pfn(). Switch to using
is_error_noslot_pfn() instead to catch this case properly.
Fixes: 858dd5d45733 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[james.hogan@imgtec.com: Backport to v4.7.y] Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
AMD F12h machines have an erratum which can cause DIV/IDIV to behave
unpredictably. The workaround is to set MSRC001_1029[31] but sometimes
there is no BIOS update containing that workaround so let's do it
ourselves unconditionally. It is simple enough.
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
Be defensive about what underlying fs provides us in the returned xattr
list buffer. If it's not properly null terminated, bail out with a warning
insead of BUG.
kernfs_notify_workfn() sends out file modified events for the
scheduled kernfs_nodes. Because the modifications aren't from
userland, it doesn't have the matching file struct at hand and can't
use fsnotify_modify(). Instead, it looked up the inode and then used
d_find_any_alias() to find the dentry and used fsnotify_parent() and
fsnotify() directly to generate notifications.
The assumption was that the relevant dentries would have been pinned
if there are listeners, which isn't true as inotify doesn't pin
dentries at all and watching the parent doesn't pin the child dentries
even for dnotify. This led to, for example, inotify watchers not
getting notifications if the system is under memory pressure and the
matching dentries got reclaimed. It can also be triggered through
/proc/sys/vm/drop_caches or a remount attempt which involves shrinking
dcache.
fsnotify_parent() only uses the dentry to access the parent inode,
which kernfs can do easily. Update kernfs_notify_workfn() so that it
uses fsnotify() directly for both the parent and target inodes without
going through d_find_any_alias(). While at it, supply the target file
name to fsnotify() from kernfs_node->name.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Fixes: d911d9874801 ("kernfs: make kernfs_notify() trigger inotify events too") Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
If crypt_alloc_tfms() had to allocate multiple tfms and it failed before
the last allocation, then it would call crypt_free_tfms() and could free
pointers from uninitialized memory -- due to the crypt_free_tfms() check
for non-zero cc->tfms[i]. Fix by allocating zeroed memory.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When dm-crypt processes writes, it allocates a new bio in
crypt_alloc_buffer(). The bio is allocated from a bio set and it can
have at most BIO_MAX_PAGES vector entries, however the incoming bio can be
larger (e.g. if it was allocated by bcache). If the incoming bio is
larger, bio_alloc_bioset() fails and an error is returned.
To avoid the error, we test for a too large bio in the function
crypt_map() and use dm_accept_partial_bio() to split the bio.
dm_accept_partial_bio() trims the current bio to the desired size and
asks DM core to send another bio with the rest of the data.
From inspection, the superblock sb_inprogress check is done in the
verifier and triggered only for the primary superblock via a
"bp->b_bn == XFS_SB_DADDR" check.
Unfortunately, the primary superblock is an uncached buffer, and
hence it is configured by xfs_buf_read_uncached() with:
bp->b_bn = XFS_BUF_DADDR_NULL; /* always null for uncached buffers */
And so this check never triggers. Fix it.
cc: <stable@vger.kernel.org> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
Commit ebb657babfa9 ("staging: comedi: ni_mio_common: clarify the
cmd->start_arg validation and use") introduced a backwards compatibility
issue in the use of asynchronous commands on the AO subdevice when
`start_src` is `TRIG_EXT`. Valid values for `start_src` are `TRIG_INT`
(for internal, software trigger), and `TRIG_EXT` (for external trigger).
When set to `TRIG_EXT`. In both cases, the driver relies on an
internal, software trigger to set things up (allowing the user
application to write sufficient samples to the data buffer before the
trigger), so it acts as a software "pre-trigger" in the `TRIG_EXT` case.
The software trigger is handled by `ni_ao_inttrig()`.
Prior to the above change, when `start_src` was `TRIG_INT`, `start_arg`
was required to be 0, and `ni_ao_inttrig()` checked that the software
trigger number was also 0. After the above change, when `start_src` was
`TRIG_INT`, any value was allowed for `start_arg`, and `ni_ao_inttrig()`
checked that the software trigger number matched this `start_arg` value.
The backwards compatibility issue is that the internal trigger number
now has to match `start_arg` when `start_src` is `TRIG_EXT` when it
previously had to be 0.
Fix the backwards compatibility issue in `ni_ao_inttrig()` by always
allowing software trigger number 0 when `start_src` is something other
than `TRIG_INT`.
Thanks to Spencer Olson for reporting the issue.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reported-by: Spencer Olson <olsonse@umich.edu> Fixes: ebb657babfa9 ("staging: comedi: ni_mio_common: clarify the cmd->start_arg validation and use") Cc: stable <stable@vger.kernel.org> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
`daqboard2000_find_boardinfo()` is supposed to check if the
DaqBoard/2000 series model is supported, based on the PCI subvendor and
subdevice ID. The current code is wrong as it is comparing the PCI
device's subdevice ID to an expected, fixed value for the subvendor ID.
It should be comparing the PCI device's subvendor ID to this fixed
value. Correct it.
A new task inherits cpus_allowed and mems_allowed masks from its parent,
but if someone changes cpuset's config by writing to cpuset.cpus/cpuset.mems
before this new task is inserted into the cgroup's task list, the new task
won't be updated accordingly.
projects / linux-stable / log