/dev/mem currently allows mmap() mappings that wrap around the end of
the physical address space, which should probably be illegal. It
circumvents the existing STRICT_DEVMEM permission check because the loop
immediately terminates (as the start address is already higher than the
end address). On the x86_64 architecture it will then cause a panic
(from the BUG(start >= end) in arch/x86/mm/pat.c:reserve_memtype()).
This patch adds an explicit check to make sure offset + size will not
wrap around in the physical address type.
Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790)
crashes during suspend tests. Geert Uytterhoeven managed to reproduce the
issue on an M2-W Koelsch board (r8a7791):
It occurs when the PME scan runs, once per second. During PME scan, the
PCI host bridge (rcar-pci) registers are accessed while its module clock
has already been disabled, leading to the crash.
One reproducer is to configure s2ram to use "s2idle" instead of "deep"
suspend:
Another reproducer is to write either "platform" or "processors" to
/sys/power/pm_test. It does not (or is less likely) to happen during full
system suspend ("core" or "none") because system suspend also disables
timers, and thus the workqueue handling PME scans no longer runs. Geert
believes the issue may still happen in the small window between disabling
module clocks and disabling timers:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test # Or "processors"
# echo mem > /sys/power/state
(Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.)
Rafael Wysocki agrees that PME scans should be suspended before the host
bridge registers become inaccessible. To that end, queue the task on a
workqueue that gets frozen before devices suspend.
Rafael notes however that as a result, some wakeup events may be missed if
they are delivered via PME from a device without working IRQ (which hence
must be polled) and occur after the workqueue has been frozen. If that
turns out to be an issue in practice, it may be possible to solve it by
calling pci_pme_list_scan() once directly from one of the host bridge's
pm_ops callbacks.
In the PCI_MMAP_PROCFS case when the address being passed by the user is a
'user visible' resource address based on the bus window, and not the actual
contents of the resource, that's what we need to be checking it against.
Enabling the tracer selftest triggers occasionally the warning in
text_poke(), which warns when the to be modified page is not marked
reserved.
The reason is that the tracer selftest installs kprobes on functions marked
__init for testing. These probes are removed after the tests, but that
removal schedules the delayed kprobes_optimizer work, which will do the
actual text poke. If the work is executed after the init text is freed,
then the warning triggers. The bug can be reproduced reliably when the work
delay is increased.
Flush the optimizer work and wait for the optimizing/unoptimizing lists to
become empty before returning from the kprobes tracer selftest. That
ensures that all operations which were queued due to the probes removal
have completed.
Link: http://lkml.kernel.org/r/20170516094802.76a468bb@gandalf.local.home Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Fixes: 6274de498 ("kprobes: Support delayed unoptimizing") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The metag implementation of strncpy_from_user() doesn't validate the src
pointer, which could allow reading of arbitrary kernel memory. Add a
short access_ok() check to prevent that.
Its still possible for it to read across the user/kernel boundary, but
it will invariably reach a NUL character after only 9 bytes, leaking
only a static kernel address being loaded into D0Re0 at the beginning of
__start, which is acceptable for the immediate fix.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __user_bad() macro used by access_ok() has a few corner cases
noticed by Al Viro where it doesn't behave correctly:
- The kernel range check has off by 1 errors which permit access to the
first and last byte of the kernel mapped range.
- The kernel range check ends at LINCORE_BASE rather than
META_MEMORY_LIMIT, which is ineffective when the kernel is in global
space (an extremely uncommon configuration).
There are a couple of other shortcomings here too:
- Access to the whole of the other address space is permitted (i.e. the
global half of the address space when the kernel is in local space).
This isn't ideal as it could theoretically still contain privileged
mappings set up by the bootloader.
- The size argument is unused, permitting user copies which start on
valid pages at the end of the user address range and cross the
boundary into the kernel address space (e.g. addr = 0x3ffffff0, size
> 0x10).
It isn't very convenient to add size checks when disallowing certain
regions, and it seems far safer to be sure and explicit about what
userland is able to access, so invert the logic to allow certain regions
instead, and fix the off by 1 errors and missing size checks. This also
allows the get_fs() == KERNEL_DS check to be more easily optimised into
the user address range case.
We now have 3 such allowed regions:
- The user address range (incorporating the get_fs() == KERNEL_DS
check).
- NULL (some kernel code expects this to work, and we'll always catch
the fault anyway).
- The core code memory region.
Fixes: 373cd784d0fc ("metag: Memory handling") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 19be0eaffa3a ("mm: remove gup_flags FOLL_WRITE games from
__get_user_pages()"), the mm code was changed from unsetting FOLL_WRITE
after a COW was resolved to setting the (newly introduced) FOLL_COW
instead. Simultaneously, the check in gup.c was updated to still allow
writes with FOLL_FORCE set if FOLL_COW had also been set.
However, a similar check in huge_memory.c was forgotten. As a result,
remote memory writes to ro regions of memory backed by transparent huge
pages cause an infinite loop in the kernel (handle_mm_fault sets
FOLL_COW and returns 0 causing a retry, but follow_trans_huge_pmd bails
out immidiately because `(flags & FOLL_WRITE) && !pmd_write(*pmd)` is
true.
While in this state the process is stil SIGKILLable, but little else
works (e.g. no ptrace attach, no other signals). This is easily
reproduced with the following code (assuming thp are set to always):
Fix this by updating follow_trans_huge_pmd in huge_memory.c analogously
to the update in gup.c in the original commit. The same pattern exists
in follow_devmap_pmd. However, we should not be able to reach that
check with FOLL_COW set, so add WARN_ONCE to make sure we notice if we
ever do.
[akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/20170106015025.GA38411@juliacomputing.com Signed-off-by: Keno Fischer <keno@juliacomputing.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Greg Thelen <gthelen@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[AmitP: Minor refactoring of upstream changes for linux-3.18.y,
where follow_devmap_pmd() doesn't exist.] Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 8dfbcc4351a0 ("[media] xc2028: avoid use after free") tried
to address the reported use-after-free by clearing the reference.
However, it's clearing the wrong pointer; it sets NULL to
priv->ctrl.fname, but it's anyway overwritten by the next line
memcpy(&priv->ctrl, p, sizeof(priv->ctrl)).
OTOH, the actual code accessing the freed string is the strcmp() call
with priv->fname:
if (!firmware_name[0] && p->fname &&
priv->fname && strcmp(p->fname, priv->fname))
free_firmware(priv);
where priv->fname points to the previous file name, and this was
already freed by kfree().
For fixing the bug properly, this patch does the following:
- Keep the copy of firmware file name in only priv->fname,
priv->ctrl.fname isn't changed;
- The allocation is done only when the firmware gets loaded;
- The kfree() is called in free_firmware() commonly
Fixes: commit 8dfbcc4351a0 ('[media] xc2028: avoid use after free') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some kernel features don't currently work if a task puts a non-zero
address tag in its stack pointer, frame pointer, or frame record entries
(FP, LR).
For example, with a tagged stack pointer, the kernel can't deliver
signals to the process, and the task is killed instead. As another
example, with a tagged frame pointer or frame records, perf fails to
generate call graphs or resolve symbols.
For now, just document these limitations, instead of finding and fixing
everything that doesn't work, as it's not known if anyone needs to use
tags in these places anyway.
In addition, as requested by Dave Martin, generalize the limitations
into a general kernel address tag policy, and refactor
tagged-pointers.txt to include it.
Fixes: d50240a5f6ce ("arm64: mm: permit use of tagged pointers at EL0") Reviewed-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our access_ok() simply hands its arguments over to __range_ok(), which
implicitly assummes that the addr parameter is 64 bits wide. This isn't
necessarily true for compat code, which might pass down a 32-bit address
parameter.
In these cases, we don't have a guarantee that the address has been zero
extended to 64 bits, and the upper bits of the register may contain
unknown values, potentially resulting in a suprious failure.
Avoid this by explicitly casting the addr parameter to an unsigned long
(as is done on other architectures), ensuring that the parameter is
widened appropriately.
Fixes: 0aea86a2176c ("arm64: User access library functions") Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Historically struct device_node references were tracked using a kref embedded as
a struct field. Commit 75b57ecf9d1d ("of: Make device nodes kobjects so they
show up in sysfs") (Mar 2014) refactored device_nodes to be kobjects such that
the device tree could by more simply exposed to userspace using sysfs.
Commit 0829f6d1f69e ("of: device_node kobject lifecycle fixes") (Mar 2014)
followed up these changes to better control the kobject lifecycle and in
particular the referecne counting via of_node_get(), of_node_put(), and
of_node_init().
A result of this second commit was that it introduced an of_node_put() call when
a dynamic node is detached, in of_node_remove(), that removes the initial kobj
reference created by of_node_init().
Traditionally as the original dynamic device node user the pseries code had
assumed responsibilty for releasing this final reference in its platform
specific DLPAR detach code.
This patch fixes a refcount underflow introduced by commit 0829f6d1f6, and
recently exposed by the upstreaming of the recount API.
Messages like the following are no longer seen in the kernel log with this
patch following DLPAR remove operations of cpus and pci devices.
rpadlpar_io: slot PHB 72 removed
refcount_t: underflow; use-after-free.
------------[ cut here ]------------
WARNING: CPU: 5 PID: 3335 at lib/refcount.c:128 refcount_sub_and_test+0xf4/0x110
Fixes: 0829f6d1f69e ("of: device_node kobject lifecycle fixes") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
[mpe: Make change log commit references more verbose] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Make sure to check the number of endpoints to avoid accessing memory
beyond the endpoint array should a device lack the expected endpoints.
Note that, as far as I can tell, the gspca framework has already made
sure there is at least one endpoint in the current alternate setting so
there should be no risk for a NULL-pointer dereference here.
Fixes: b517af722860 ("V4L/DVB: gspca_konica: New gspca subdriver for
konica chipset using cams")
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should call ipxitf_put() if the copy_to_user() fails.
Reported-by: 李强 <liqiang6-s@360.cn> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line discipline drivers may mistakenly misuse ldisc-related fields
when initializing. For example, a failure to initialize tty->receive_room
in the N_GIGASET_M101 line discipline was recently found and fixed [1].
Now, the N_X25 line discipline has been discovered accessing the previous
line discipline's already-freed private data [2].
Harden the ldisc interface against misuse by initializing revelant
tty fields before instancing the new line discipline.
Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).
Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop erroneous cpu_to_le32 when setting the baud rate, something which
corrupted the divisor on big-endian hosts.
Found using sparse:
warning: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] val
got restricted __le32 [usertype] <noident>
Fixes: af2ac1a091bc ("USB: serial mct_usb232: move DMA buffers to heap") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-By: Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use new USB device IDs for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check for the required out endpoint to avoid dereferencing
a NULL-pointer in mce_request_packet should a malicious device lack such
an endpoint. Note that this path is hit during probe.
Fixes: 66e89522aff7 ("V4L/DVB: IR: add mceusb IR receiver driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 2a9f8b5d25be ("V4L/DVB (5206): Usbvision: set alternate interface
modification")
Add missing endianness conversion when using the USB device-descriptor
bcdDevice field to construct a firmware file name.
Fixes: 8ef80aef118e ("[IRDA]: irda-usb.c: STIR421x cleanups") Cc: Nick Fedchik <nfedchik@atlantic-link.com.ua> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
This patch adds support for recognition of ARM-USB-TINY(H) devices which
are almost identical to ARM-USB-OCD(H) but lacking separate barrel jack
and serial console.
By suggestion from Johan Hovold it is possible to replace
ftdi_jtag_quirk with a bit more generic construction. Since all
Olimex-ARM debuggers has exactly two ports, we could safely always use
only second port within the debugger family.
Commit 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY
flag") enables unprivileged users to set the FTDI latency timer,
but there was a logic flaw that skipped sending the corresponding
USB control message to the device.
Specifically, the device latency timer would not be updated until next
open, something which was later also inadvertently broken by commit c19db4c9e49a ("USB: ftdi_sio: set device latency timeout at port
probe").
A recent commit c6dce2626606 ("USB: serial: ftdi_sio: fix extreme
low-latency setting") disabled the low-latency mode by default so we now
need this fix to allow unprivileged users to again enable it.
Signed-off-by: Anthony Mallet <anthony.mallet@laas.fr>
[johan: amend commit message] Fixes: 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY flag") Fixes: c19db4c9e49a ("USB: ftdi_sio: set device latency timeout at port probe"). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code can potentially sleep for an indefinite amount of time in
zap_pid_ns_processes triggering the hung task timeout, and increasing
the system average. This is undesirable. Sleep with a task state of
TASK_INTERRUPTIBLE instead of TASK_UNINTERRUPTIBLE to remove these
undesirable side effects.
Apparently under heavy load this has been allowing Chrome to trigger
the hung time task timeout error and cause ChromeOS to reboot.
Reported-by: Vovo Yang <vovoy@google.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Fixes: 6347e9009104 ("pidns: guarantee that the pidns init will be the last pidns process reaped") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory allocator passed to __unflatten_device_tree() (e.g. a wrapped
kzalloc) can fail so add the missing sanity check to avoid dereferencing
a NULL pointer.
Fixes: fe14042358fa ("of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notifications may only be 8 bytes long. Accessing the 9th and
10th byte of unimplemented/unknown notifications may be insecure.
Also check the length of known notifications before accessing anything
behind the 8th byte.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43530b69d758328d3ffe6ab98fd640463e8e3667 ("regulator: Use
regmap_read/write(), regmap_update_bits functions directly") intended
to replace working inline helper functions with standard regmap
calls. However, it also inverted the set/clear logic of the "CORE ADJ
Allowed" bit. That patch was clearly never tested, since without that
bit cleared, the core VDCDC1 voltage output does not react to I2C
configuration changes.
This patch fixes the issue by clearing the bit as in the original,
correct implementation. Note for stable back porting that, due to
subsequent driver churn, this patch will not apply on every kernel
version.
Fixes: 43530b69d758 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly") Signed-off-by: Richard Cochran <rcochran@linutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modifying the attributes of a file makes ima_inode_post_setattr reset
the IMA cache flags. So if the file, which has just been created,
is opened a second time before the first file descriptor is closed,
verification fails since the security.ima xattr has not been written
yet. We therefore have to look at the IMA_NEW_FILE even if the file
already existed.
With this patch there should no longer be an error when cat tries to
open testfile:
Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.
However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.
Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.
Noticed by KASAN when forcing a reset via:
echo 1 > /sys/bus/pci/.../reset
The same code path can presumably be exercised in remove() and
shutdown().
This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095c51a ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.
Fixes: fc3314609047 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__get_memory_limit() tests if dm_bufio_cache_size changed and calls
__cache_size_refresh() if it did. It takes dm_bufio_clients_lock while
it already holds the client lock. However, lock ordering is violated
because in cleanup_old_buffers() dm_bufio_clients_lock is taken before
the client lock.
This results in a possible deadlock and lockdep engine warning.
Fix this deadlock by changing mutex_lock() to mutex_trylock(). If the
lock can't be taken, it will be re-checked next time when a new buffer
is allocated.
Also add "unlikely" to the if condition, so that the optimizer assumes
that the condition is false.
dm_btree_find_lowest_key() is giving incorrect results. find_key()
traverses the btree correctly for finding the highest key, but there is
an error in the way it traverses the btree for retrieving the lowest
key. dm_btree_find_lowest_key() fetches the first key of the rightmost
block of the btree instead of fetching the first key from the leftmost
block.
Fix this by conditionally passing the correct parameter to value64()
based on the @find_highest flag.
Signed-off-by: Erez Zadok <ezk@fsl.cs.sunysb.edu> Signed-off-by: Vinothkumar Raja <vinraja@cs.stonybrook.edu> Signed-off-by: Nidhi Panpalia <npanpalia@cs.stonybrook.edu> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]
The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.
Reported-By: Roee Hay <roee.hay@hcl.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ene_usb6250 sub-driver in usb-storage does USB I/O to buffers on
the stack, which doesn't work with vmapped stacks. This patch fixes
the problem by allocating a separate 512-byte buffer at probe time and
using it for all of the offending I/O operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “tread” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA timer ioctls have an open race and this may lead to a
use-after-free of timer instance object. A simplistic fix is to make
each ioctl exclusive. We have already tread_sem for controlling the
tread, and extend this as a global mutex to be applied to each ioctl.
The downside is, of course, the worse concurrency. But these ioctls
aren't to be parallel accessible, in anyway, so it should be fine to
serialize there.
ALSA sequencer code has an open race between the timer setup ioctl and
the close of the client. This was triggered by syzkaller fuzzer, and
a use-after-free was caught there as a result.
This patch papers over it by adding a proper queue->timer_mutex lock
around the timer-related calls in the relevant code path.
Until now, hitting this BUG_ON caused a recursive oops (because oops
handling involves do_exit(), which calls into the scheduler, which in
turn raises an oops), which caused stuff below the stack to be
overwritten until a panic happened (e.g. via an oops in interrupt
context, caused by the overwritten CPU index in the thread_info).
Just panic directly.
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[AmitP: Minor refactoring of upstream changes for linux-3.18.y] Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae8778 ("usbnet: cdc_ncm: apply usbnet_link_change") Reported-by: Andrey Konovalov <andreyknvl@gmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Plugging a Logitech DJ receiver with KASAN activated raises a bunch of
out-of-bound readings.
The fields are allocated up to MAX_USAGE, meaning that potentially, we do
not have enough fields to fit the incoming values.
Add checks and silence KASAN.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd296 ("ppp: take reference on channels netns") Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz> Cc: Paul Mackerras <paulus@samba.org> Cc: linux-ppp@vger.kernel.org Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While cooking the sctp np->opt rcu fixes, I forgot to move
one rcu_read_unlock() after the added rcu_dereference() in
sctp_v6_get_dst()
This gave lockdep warnings reported by Dave Jones.
Fixes: c836a8ba9386 ("ipv6: sctp: add rcu protection around np->opt") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch completes the work I did in commit 45f6fad84cc3
("ipv6: add complete rcu protection around np->opt"), as I missed
sctp part.
This simply makes sure np->opt is used with proper RCU locking
and accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().
Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.
This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:
The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.
Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.
KASAN was extremely helpful in finding the root cause of this bug.
Signed-off-by: Calvin Owens <calvinowens@fb.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a use-after-free possibility in __ext4_journal_stop() in the
case that we free the handle in the first jbd2_journal_stop() because
we're referencing handle->h_err afterwards. This was introduced in 9705acd63b125dee8b15c705216d7186daea4625 and it is wrong. Fix it by
storing the handle->h_err value beforehand and avoid referencing
potentially freed handle.
Fixes: 9705acd63b125dee8b15c705216d7186daea4625 Signed-off-by: Lukas Czerner <lczerner@redhat.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ASN.1 decoder, when the length field of an ASN.1 value is extracted,
it isn't validated against the remaining amount of data before being added
to the cursor. With a sufficiently large size indicated, the check:
datalen - dp < 2
may then fail due to integer overflow.
Fix this by checking the length indicated against the amount of remaining
data in both places a definite length is determined.
Whilst we're at it, make the following changes:
(1) Check the maximum size of extended length does not exceed the capacity
of the variable it's being stored in (len) rather than the type that
variable is assumed to be (size_t).
(2) Compare the EOC tag to the symbolic constant ASN1_EOC rather than the
integer 0.
(3) To reduce confusion, move the initialisation of len outside of:
for (len = 0; n > 0; n--) {
since it doesn't have anything to do with the loop counter n.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Peter Jones <pjones@redhat.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ASN.1 decoder is asked to parse a sequence of objects, non-optional
matches get skipped if there's no more data to be had rather than a
data-overrun error being reported.
This is due to the code segment that decides whether to skip optional
matches (ie. matches that could get ignored because an element is marked
OPTIONAL in the grammar) due to a lack of data also skips non-optional
elements if the data pointer has reached the end of the buffer.
This can be tested with the data decoder for the new RSA akcipher algorithm
that takes three non-optional integers. Currently, it skips the last
integer if there is insufficient data.
Without the fix, #defining DEBUG in asn1_decoder.c will show something
like:
The next_op line for pc=8/13 should be followed by a match line.
This is not exploitable for X.509 certificates by means of shortening the
message and fixing up the ASN.1 CONS tags because:
(1) The relevant records being built up are cleared before use.
(2) If the message is shortened sufficiently to remove the public key, the
ASN.1 parse of the RSA key will fail quickly due to a lack of data.
(3) Extracted signature data is either turned into MPIs (which cope with a
0 length) or is simpler integers specifying algoritms and suchlike
(which can validly be 0); and
(4) The AKID and SKID extensions are optional and their removal is handled
without risking passing a NULL to asymmetric_key_generate_id().
(5) If the certificate is truncated sufficiently to remove the subject,
issuer or serialNumber then the ASN.1 decoder will fail with a 'Cons
stack underflow' return.
This is not exploitable for PKCS#7 messages by means of removal of elements
from such a message from the tail end of a sequence:
(1) Any shortened X.509 certs embedded in the PKCS#7 message are survivable
as detailed above.
(2) The message digest content isn't used if it shows a NULL pointer,
similarly, the authattrs aren't used if that shows a NULL pointer.
(3) A missing signature results in a NULL MPI - which the MPI routines deal
with.
(4) If data is NULL, it is expected that the message has detached content and
that is handled appropriately.
(5) If the serialNumber is excised, the unconditional action associated
with it will pick up the containing SEQUENCE instead, so no NULL
pointer will be seen here.
If both the issuer and the serialNumber are excised, the ASN.1 decode
will fail with an 'Unexpected tag' return.
In either case, there's no way to get to asymmetric_key_generate_id()
with a NULL pointer.
(6) Other fields are decoded to simple integers. Shortening the message
to omit an algorithm ID field will cause checks on this to fail early
in the verification process.
This can also be tested by snipping objects off of the end of the ASN.1 stream
such that mandatory tags are removed - or even from the end of internal
SEQUENCEs. If any mandatory tag is missing, the error EBADMSG *should* be
produced. Without this patch ERANGE or ENOPKG might be produced or the parse
may apparently succeed, perhaps with ENOKEY or EKEYREJECTED being produced
later, depending on what gets snipped.
Just snipping off the final BIT_STRING or OCTET_STRING from either sample
should be a start since both are mandatory and neither will cause an EBADMSG
without the patches
Reported-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Marcel Holtmann <marcel@holtmann.org> Reviewed-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race on CPU unplug where we free the swevent hash array
while it can still have events on. This will result in a
use-after-free which is BAD.
Simply do not free the hash array on unplug. This leaves the thing
around and no use-after-free takes place.
When the last swevent dies, we do a for_each_possible_cpu() iteration
anyway to clean these up, at which time we'll free it, so no leakage
will occur.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf core implicitly rejects events spanning multiple HW PMUs, as in
these cases the event->ctx will differ. However this validation is
performed after pmu::event_init() is called in perf_init_event(), and
thus pmu::event_init() may be called with a group leader from a
different HW PMU.
The ARM64 PMU driver does not take this fact into account, and when
validating groups assumes that it can call to_arm_pmu(event->pmu) for
any HW event. When the event in question is from another HW PMU this is
wrong, and results in dereferencing garbage.
This patch updates the ARM64 PMU driver to first test for and reject
events from other PMUs, moving the to_arm_pmu and related logic after
this test. Fixes a crash triggered by perf_fuzzer on Linux-4.0-rc2, with
a CCI PMU present:
Also cleans up the code to use the arm_pmu only when we know
that we are dealing with an arm pmu event.
Cc: Will Deacon <will.deacon@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Peter Ziljstra (Intel) <peterz@infradead.org> Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with x86, mark the sys_call_table const such that it will be placed
in the .rodata section. This will cause attempts to modify the table
(accidental or deliberate) to fail when strict page permissions are in
place. In the absence of strict page permissions, there should be no
functional change.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being
defined as 0x80000000. This results in sendmsg failure if used from 32bit
userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT
in flags check in hci_sock_sendmsg.
Make sure to actually suspend the device before returning after a failed
(or deferred) probe.
Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.
Fixes: 388bc2622680 ("omap-serial: Fix the error handling in the omap_serial probe") Cc: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)
Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.
Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.
Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.
Fixes: 7e9c8e7dbf3b ("serial: omap: make sure to suspend device before remove") Cc: Felipe Balbi <balbi@kernel.org> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix_sync_read_error() modifies a bio on a newly faulty
device by setting bi_end_io to end_sync_write.
This ensure that put_buf() will still call rdev_dec_pending()
as required, but makes sure that subsequent code in
fix_sync_read_error() doesn't try to read from the device.
Unfortunately this interacts badly with sync_request_write()
which assumes that any bio with bi_end_io set to non-NULL
other than end_sync_read is safe to write to.
As the device is now faulty it doesn't make sense to write.
As the bio was recently used for a read, it is "dirty"
and not suitable for immediate submission.
In particular, ->bi_next might be non-NULL, which will cause
generic_make_request() to complain.
Break this interaction by refusing to write to devices
which are marked as Faulty.
Reported-and-tested-by: Michael Wang <yun.wang@profitbricks.com> Fixes: 2e52d449bcec ("md/raid1: add failfast handling for reads.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The author meant to free the variable that was just allocated, instead
of the one that failed to be allocated, but made a simple typo. This
patch rectifies that.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macs send the maximum buffer size in response on ioctl to validate
negotiate security information, which causes us to fail the mount
as the response buffer is larger than the expected response.
Changed ioctl response processing to allow for padding of validate
negotiate ioctl response and limit the maximum response size to
maximum buffer size.
Signed-off-by: Steve French <steve.french@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getxattr uses vmalloc to allocate memory if kzalloc fails. This is
filled by vfs_getxattr and then copied to the userspace. vmalloc,
however, doesn't zero out the memory so if the specific implementation
of the xattr handler is sloppy we can theoretically expose a kernel
memory. There is no real sign this is really the case but let's make
sure this will not happen and use vzalloc instead.
In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs.
However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not
called to free the allocated EQs.
Fixes: e605b743f33d ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.
Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.
Fixes: 1732b0ef3b3a ([IPoIB] add path record information in debugfs) Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com> Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.
This is broken since ever but sadly nobody noticed.
Recent versions of GDB set DR_CONTROL unconditionally and
UML dies due to a heap corruption. It turns out that
the PTRACE_POKEUSER was copy&pasted from i386 and assumes
that addresses are 4 bytes long.
Fix that by using 8 as address size in the calculation.
Reported-by: jie cao <cj3054@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum size for a new stack (512 bytes) setup for arch/x86/boot components
when the bootloader does not setup/provide a stack for the early boot components
is not "enough".
The setup code executing as part of early kernel startup code, uses the stack
beyond 512 bytes and accidentally overwrites and corrupts part of the BSS
section. This is exposed mostly in the early video setup code, where
it was corrupting BSS variables like force_x, force_y, which in-turn affected
kernel parameters such as screen_info (screen_info.orig_video_cols) and
later caused an exception/panic in console_init().
Most recent boot loaders setup the stack for early boot components, so this
stack overwriting into BSS section issue has not been exposed.
Signed-off-by: Ashish Kalra <ashish@bluestacks.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.local Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.
Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Source:
(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773 /* We don't need to check interfaces that are
1774 * disabled for runtime PM. Either they are unbound
1775 * or else their drivers don't support autosuspend
1776 * and so they are permanently active.
1777 */
1778 if (intf->dev.power.disable_depth)
1779 continue;
1780 if (atomic_read(&intf->dev.power.usage_count) > 0)
1781 return -EBUSY;
1782 w |= intf->needs_remote_wakeup;
Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().
To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
projects / linux-stable / log