Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The retry logic for netlink_attachskb() inside sys_mq_notify()
is nasty and vulnerable:
1) The sock refcnt is already released when retry is needed
2) The fd is controllable by user-space because we already
release the file refcnt
so we when retry but the fd has been just closed by user-space
during this small window, we end up calling netlink_detachskb()
on the error path which releases the sock again, later when
the user-space closes this socket a use-after-free could be
triggered.
Setting 'sock' to NULL here should be sufficient to fix it.
Reported-by: GeneBlue <geneblue.mail@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The handling of the might_cancel queueing is not properly protected, so
parallel operations on the file descriptor can race with each other and
lead to list corruptions or use after free.
Protect the context for these operations with a seperate lock.
The wait queue lock cannot be reused for this because that would create a
lock inversion scenario vs. the cancel lock. Replacing might_cancel with an
atomic (atomic_t or atomic bit) does not help either because it still can
race vs. the actual list operation.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "linux-fsdevel@vger.kernel.org" Cc: syzkaller <syzkaller@googlegroups.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701311521430.3457@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In some cases, offset can overflow and can cause an infinite loop in
ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and
cap it at IPV6_MAXPLEN, since packets larger than that should be invalid.
This problem has been here since before the beginning of git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
'__vmalloc_start_set' currently only gets set in initmem_init() when
!CONFIG_NEED_MULTIPLE_NODES. This breaks detection of vmalloc address
with virt_addr_valid() with CONFIG_NEED_MULTIPLE_NODES=y, causing
a kernel crash:
[mm/usercopy] 517e1fbeb6: kernel BUG at arch/x86/mm/physaddr.c:78!
Set '__vmalloc_start_set' appropriately for that case as well.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: dc16ecf7fd1f ("x86-32: use specific __vmalloc_start_set flag in __virt_addr_valid") Link: http://lkml.kernel.org/r/1494278596-30373-1-git-send-email-labbott@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While working on another build error, I ran into several variations of
this dependency loop:
subsection "Kconfig recursive dependency limitations"
drivers/input/Kconfig:8: symbol INPUT is selected by VT
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/tty/Kconfig:12: symbol VT is selected by FB_STI
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/video/fbdev/Kconfig:677: symbol FB_STI depends on FB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/Kconfig:72: symbol DRM_KMS_FB_HELPER is selected by DRM_KMS_CMA_HELPER
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/Kconfig:137: symbol DRM_KMS_CMA_HELPER is selected by DRM_HDLCD
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/arm/Kconfig:6: symbol DRM_HDLCD depends on OF
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/of/Kconfig:4: symbol OF is selected by X86_INTEL_CE
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:523: symbol X86_INTEL_CE depends on X86_IO_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:1011: symbol X86_IO_APIC depends on X86_LOCAL_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:1005: symbol X86_LOCAL_APIC depends on X86_UP_APIC
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
arch/x86/Kconfig:980: symbol X86_UP_APIC depends on PCI_MSI
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pci/Kconfig:11: symbol PCI_MSI is selected by AMD_IOMMU
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/iommu/Kconfig:106: symbol AMD_IOMMU depends on IOMMU_SUPPORT
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/iommu/Kconfig:5: symbol IOMMU_SUPPORT is selected by DRM_ETNAVIV
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/etnaviv/Kconfig:2: symbol DRM_ETNAVIV depends on THERMAL
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/thermal/Kconfig:5: symbol THERMAL is selected by ACPI_VIDEO
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/acpi/Kconfig:183: symbol ACPI_VIDEO is selected by INPUT
This doesn't currently show up as I fixed the 'THERMAL' part of it,
but I noticed that the FB_STI dependency should not be there but
was introduced by slightly incorrect bug-fix patch that tried to
fix a link error.
Instead of selecting 'VT' to make us enter the drivers/video/console
directory at compile-time, it's sufficient to build the
drivers/video/console/sticore.c file by adding its directory
to when CONFIG_FB_STI is enabled. Alternatively, we could move the
sticore code to another directory that is always built when we
have at STI_CONSOLE or FB_STI enabled.
Fixes: 17085a934592 ("parisc: stifb: should depend on STI_CONSOLE") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is broken since ever but sadly nobody noticed.
Recent versions of GDB set DR_CONTROL unconditionally and
UML dies due to a heap corruption. It turns out that
the PTRACE_POKEUSER was copy&pasted from i386 and assumes
that addresses are 4 bytes long.
Fix that by using 8 as address size in the calculation.
Reported-by: jie cao <cj3054@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
January is month 1. There is no zero-th month. If someone passes a
zero month then it means we read from one space before the start of the
total_days_of_prev_months[] array.
We may as well also be strict about days as well.
Fixes: 1bd5bbcb6531 ("[CIFS] Legacy time handling for Win9x and OS/2 part 1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Be careful when comparing tcp_time_stamp to some u32 quantity,
otherwise result can be surprising.
Fixes: 7c106d7e782b ("[TCP]: TCP Low Priority congestion control") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since that change also made the nfrag function not necessary
for exports, remove it.
Fixes: 89a23c8b528b ("ip6_tunnel: Fix missing tunnel encapsulation limit option") Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The IPv6 tunneling code tries to insert IPV6_TLV_TNL_ENCAP_LIMIT and
IPV6_TLV_PADN options when an encapsulation limit is defined (the
default is a limit of 4). An MTU adjustment is done to account for
these options as well. However, the options are never present in the
generated packets.
The issue appears to be a subtlety between IPV6_DSTOPTS and
IPV6_RTHDRDSTOPTS defined in RFC 3542. When the IPIP tunnel driver was
written, the encap limit options were included as IPV6_RTHDRDSTOPTS in
dst0opt of struct ipv6_txoptions. Later, ipv6_push_nfrags_opts was
(correctly) updated to require IPV6_RTHDR options when IPV6_RTHDRDSTOPTS
are to be used. This caused the options to no longer be included in v6
encapsulated packets.
The fix is to use IPV6_DSTOPTS (in dst1opt of struct ipv6_txoptions)
instead. IPV6_DSTOPTS do not have the additional IPV6_RTHDR requirement.
Fixes: 1df64a8569c7: ("[IPV6]: Add ip6ip6 tunnel driver.") Fixes: 333fad5364d6: ("[IPV6]: Support several new sockopt / ancillary data in Advanced API (RFC3542)") Signed-off-by: Craig Gallek <kraig@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This changed is needed to avoid locking problem during
boot as shown:
<5>[ 8.824096] Registering SWP/SWPB emulation handler
<6>[ 8.977294] clock: disabling unused clocks to save power
<3>[ 9.108154] BUG: sleeping function called from invalid context at kernel_albert/kernel/mutex.c:269
<3>[ 9.122894] in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper/0
<4>[ 9.130249] 3 locks held by swapper/0/1:
<4>[ 9.134613] #0: (&__lockdep_no_validate__){......}, at: [<c0342430>] __driver_attach+0x58/0xa8
<4>[ 9.144500] #1: (&__lockdep_no_validate__){......}, at: [<c0342440>] __driver_attach+0x68/0xa8
<4>[ 9.154357] #2: (&polling_timer){......}, at: [<c0053770>] run_timer_softirq+0x108/0x3ec
<4>[ 9.163726] Backtrace:
<4>[ 9.166473] [<c001269c>] (dump_backtrace+0x0/0x114) from [<c067e5f0>] (dump_stack+0x20/0x24)
<4>[ 9.175811] r6:00203230 r5:0000010d r4:d782e000 r3:60000113
<4>[ 9.182250] [<c067e5d0>] (dump_stack+0x0/0x24) from [<c007441c>] (__might_sleep+0x10c/0x128)
<4>[ 9.191650] [<c0074310>] (__might_sleep+0x0/0x128) from [<c0688f60>] (mutex_lock_nested+0x34/0x36c)
<4>[ 9.201660] r5:c02d5350 r4:d79a0c64
<4>[ 9.205688] [<c0688f2c>] (mutex_lock_nested+0x0/0x36c) from [<c02d5350>] (regulator_set_current_limit+0x30/0x118)
<4>[ 9.217071] [<c02d5320>] (regulator_set_current_limit+0x0/0x118) from [<c0435ce0>] (update_charger+0x84/0xc4)
<4>[ 9.228027] r7:d782fb20 r6:00000101 r5:c1767e94 r4:00000000
<4>[ 9.234436] [<c0435c5c>] (update_charger+0x0/0xc4) from [<c0435d40>] (psy_changed+0x20/0x48)
<4>[ 9.243804] r5:d782e000 r4:c1767e94
<4>[ 9.247802] [<c0435d20>] (psy_changed+0x0/0x48) from [<c0435dec>] (polling_timer_func+0x84/0xb8)
<4>[ 9.257537] r4:c1767e94 r3:00000002
<4>[ 9.261566] [<c0435d68>] (polling_timer_func+0x0/0xb8) from [<c00537e4>] (run_timer_softirq+0x17c/0x3ec)
<4>[ 9.272033] r4:c1767eb0 r3:00000000
<4>[ 9.276062] [<c0053668>] (run_timer_softirq+0x0/0x3ec) from [<c004b000>] (__do_softirq+0xf0/0x298)
<4>[ 9.286010] [<c004af10>] (__do_softirq+0x0/0x298) from [<c004b650>] (irq_exit+0x98/0xa0)
<4>[ 9.295013] [<c004b5b8>] (irq_exit+0x0/0xa0) from [<c000edbc>] (handle_IRQ+0x60/0xc0)
<4>[ 9.303680] r4:c1194e98 r3:c00bc778
<4>[ 9.307708] [<c000ed5c>] (handle_IRQ+0x0/0xc0) from [<c0008504>] (gic_handle_irq+0x34/0x68)
<4>[ 9.316955] r8:000ac383 r7:d782fc3c r6:d782fc08 r5:c11936c4 r4:e0802100
<4>[ 9.324310] r3:c026ba48
<4>[ 9.327301] [<c00084d0>] (gic_handle_irq+0x0/0x68) from [<c068c2c0>] (__irq_svc+0x40/0x74)
<4>[ 9.336456] Exception stack(0xd782fc08 to 0xd782fc50)
<4>[ 9.342041] fc00: d6e30e6cac38362700000000ac383417ea19c000ea200000
<4>[ 9.351104] fc20: beffffff00000667000ac383d6e30670d6e3066cd782fc94d782fbe8d782fc50
<4>[ 9.360168] fc40: c026ba48c001d1f000000113ffffffff
Fixes: b2998049cfae ("[BATTERY] pda_power platform driver") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[bwh: Backported to 3.2:
- Drop changes in otg_handle_notification()
- Adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being
defined as 0x80000000. This results in sendmsg failure if used from 32bit
userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT
in flags check in hci_sock_sendmsg.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl> Signed-off-by: Marko Kiiskila <marko@runtime.io> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since commit 5093bb965a163 ("powerpc/QE: switch to the cpm_muram
implementation"), muram area is not part of immrbar mapping anymore
so immrbar_virt_to_phys() is not usable anymore.
Fixes: 5093bb965a163 ("powerpc/QE: switch to the cpm_muram implementation") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Li Yang <pku.leo@gmail.com> Signed-off-by: Scott Wood <oss@buserror.net>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The WRITE SAME to TRIM translation rewrites the DATA OUT buffer. While
the SCSI code accomodates for this by passing a read-writable buffer
userspace applications don't cater for this behavior. In fact it can
be used to rewrite e.g. a readonly file through mmap and should be
considered as a security fix.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Tejun Heo <tj@kernel.org>
[bwh: Backported to 3.2:
- Open-code blk_rq_is_passthrough()
- We don't distinguish which field is invaid so goto invalid_fld
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The Infiniband spec defines "A multicast address is defined by a
MGID and a MLID" (section 10.5). Currently the MLID value is not
validated.
Add check to verify that the MLID value is in the correct address
range.
Fixes: 0c33aeedb2cf ("[IB] Add checks to multicast attach and detach") Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com> Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.2: use literal number instead of IB_MULTICAST_LID_BASE] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A list of MGID/MLID pairs is built when doing a multicast attach. When
the multicast detach is called, the list is searched, and regardless of
the search outcome, the driver detach is called.
If an MGID/MLID pair is not on the list, driver detach should not be
called, and an error should be returned. Calling the driver without
removing an MGID/MLID pair from the list can leave the core and driver
out of sync.
Fixes: f4e401562c11 ("IB/uverbs: track multicast group membership for userspace QPs") Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Felipe Balbi <balbi@kernel.org> Cc: Felix Fietkau <nbd@nbd.name> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: linux-snps-arc@lists.infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ASUS M2N-LR should not trigger boot interrupt quirks although it
carries an Intel 6702PXH. On this board the boot interrupt quirks cause
incorrect IRQ assignments and should be disabled.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43074 Tested-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After converting to use rcu for conntrack hash, one CPU may update
the ct->status via ctnetlink, while another CPU may process the
packets and update the ct->status.
So the non-atomic operation "ct->status |= status;" via ctnetlink
becomes unsafe, and this may clear the IPS_DYING_BIT bit set by
another CPU unexpectedly. For example:
CPU0 CPU1
ctnetlink_change_status __nf_conntrack_find_get
old = ct->status nf_ct_gc_expired
- nf_ct_kill
- test_and_set_bit(IPS_DYING_BIT
new = old | status; -
ct->status = new; <-- oops, _DYING_ is cleared!
Now using a series of atomic bit operation to solve the above issue.
Also note, user shouldn't set IPS_TEMPLATE, IPS_SEQ_ADJUST directly,
so make these two bits be unchangable too.
If we set the IPS_TEMPLATE_BIT, ct will be freed by nf_ct_tmpl_free,
but actually it is alloced by nf_conntrack_alloc.
If we set the IPS_SEQ_ADJUST_BIT, this may cause the NULL pointer
deference, as the nfct_seqadj(ct) maybe NULL.
Last, add some comments to describe the logic change due to the
commit a963d710f367 ("netfilter: ctnetlink: Fix regression in CTA_STATUS
processing"), which makes me feel a little confusing.
Fixes: 76507f69c44e ("[NETFILTER]: nf_conntrack: use RCU for conntrack hash") Signed-off-by: Liping Zhang <zlpnobody@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.2:
- IPS_UNCHANGEABLE_MASK was not previously defined and ctnetlink_update_status()
is not needed
- enum ip_conntrack_status only assigns 13 bits
- Adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The minimum size for a new stack (512 bytes) setup for arch/x86/boot components
when the bootloader does not setup/provide a stack for the early boot components
is not "enough".
The setup code executing as part of early kernel startup code, uses the stack
beyond 512 bytes and accidentally overwrites and corrupts part of the BSS
section. This is exposed mostly in the early video setup code, where
it was corrupting BSS variables like force_x, force_y, which in-turn affected
kernel parameters such as screen_info (screen_info.orig_video_cols) and
later caused an exception/panic in console_init().
Most recent boot loaders setup the stack for early boot components, so this
stack overwriting into BSS section issue has not been exposed.
Signed-off-by: Ashish Kalra <ashish@bluestacks.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.local Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Enabling vflip currently causes wrong colors.
It seems that (at least with the current sensor setup) REG04_VFLIP_IMG only
changes the vertical readout direction.
Because pixels are arranged RGRG... in odd lines and GBGB... in even lines,
either a one line shift or even/odd line swap is required, too, but
apparently this doesn't happen.
I finally figured out that this can be done manually by setting
REG04_VREF_EN.
Looking at hflip, it turns out that bit REG04_HREF_EN is set there
permanetly, but according to my tests has no effect on the pixel readout
order.
So my conclusion is that the current documentation of sensor register 0x04
is wrong (has changed after preliminary datasheet version 2.2).
I'm pretty sure that automatic vertical line shift/switch can be enabled,
too, but until anyone finds ot how this works, we have to stick with manual
switching.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We recently introduced some new error paths but the unlocks are missing. Fixes: 0065a79a8698 ('[media] dw2102: Don't use dynamic static allocation') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dw2102.c:368:1: warning: 'dw2102_earda_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:449:1: warning: 'dw2104_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:512:1: warning: 'dw3101_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:621:1: warning: 's6x0_i2c_transfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ttusb2_msg function uses on-stack variables to submit commands to
dvb_usb_generic. This eventually gets to the DMA api layer and will throw a
traceback if the debugging options are set.
This allocates the temporary buffer variables with kzalloc instead.
Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790)
crashes during suspend tests. Geert Uytterhoeven managed to reproduce the
issue on an M2-W Koelsch board (r8a7791):
It occurs when the PME scan runs, once per second. During PME scan, the
PCI host bridge (rcar-pci) registers are accessed while its module clock
has already been disabled, leading to the crash.
One reproducer is to configure s2ram to use "s2idle" instead of "deep"
suspend:
Another reproducer is to write either "platform" or "processors" to
/sys/power/pm_test. It does not (or is less likely) to happen during full
system suspend ("core" or "none") because system suspend also disables
timers, and thus the workqueue handling PME scans no longer runs. Geert
believes the issue may still happen in the small window between disabling
module clocks and disabling timers:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test # Or "processors"
# echo mem > /sys/power/state
(Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.)
Rafael Wysocki agrees that PME scans should be suspended before the host
bridge registers become inaccessible. To that end, queue the task on a
workqueue that gets frozen before devices suspend.
Rafael notes however that as a result, some wakeup events may be missed if
they are delivered via PME from a device without working IRQ (which hence
must be polled) and occur after the workqueue has been frozen. If that
turns out to be an issue in practice, it may be possible to solve it by
calling pci_pme_list_scan() once directly from one of the host bridge's
pm_ops callbacks.
PCI exposes files like /proc/bus/pci/00/00.0 in procfs. These files
support operations like this:
ioctl(fd, PCIIOC_MMAP_IS_IO); # request I/O port space
ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining
mmap(fd, ...)
Write combining is useful on PCI memory space, but I don't think it makes
sense on PCI I/O port space.
We *could* change proc_bus_pci_ioctl() to make it impossible to set
mmap_state == pci_mmap_io and write_combine at the same time, but that
would break the following sequence, which is currently legal:
mmap(fd, ...) # default is I/O, non-combining
ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining
ioctl(fd, PCIIOC_MMAP_IS_MEM); # request memory space
mmap(fd, ...) # get write-combining mapping
Ignore the write-combining flag when mapping I/O port space.
This patch should have no functional effect, based on this analysis of all
implementations of pci_mmap_page_range():
- ia64 mips parisc sh unicore32 x86 do not support mapping of I/O port
space at all.
- arm cris microblaze mn10300 sparc xtensa support mapping of I/O port
space, but ignore the write_combine argument to pci_mmap_page_range().
- powerpc supports mapping of I/O port space and uses write_combine, and
it disables write combining for I/O port space in
__pci_mmap_set_pgprot().
This patch makes it possible to remove __pci_mmap_set_pgprot() from
powerpc, which simplifies that path.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the PCI_MMAP_PROCFS case when the address being passed by the user is a
'user visible' resource address based on the bus window, and not the actual
contents of the resource, that's what we need to be checking it against.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The author meant to free the variable that was just allocated, instead
of the one that failed to be allocated, but made a simple typo. This
patch rectifies that.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Cc: Sri Deevi <Srinivasa.Deevi@conexant.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are numerous issues in error handling code of cx231xx initialization.
Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources()
and then cx231xx_usb_probe() does the same) and memory leaks
(e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe())
are just a few of them.
The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev()
by moving usb_get_dev(interface_to_usbdev(interface)) below in code and
implementing proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[bwh: Backported to 3.2:
- Keep using &= rather than clear_bit()
- Adjust filename, context Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 2a9f8b5d25be ("V4L/DVB (5206): Usbvision: set alternate interface
modification")
Cc: Thierry MERLE <thierry.merle@free.fr> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid accessing memory
beyond the endpoint array should a device lack the expected endpoints.
Note that, as far as I can tell, the gspca framework has already made
sure there is at least one endpoint in the current alternate setting so
there should be no risk for a NULL-pointer dereference here.
Fixes: b517af722860 ("V4L/DVB: gspca_konica: New gspca subdriver for
konica chipset using cams")
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Notifications may only be 8 bytes long. Accessing the 9th and
10th byte of unimplemented/unknown notifications may be insecure.
Also check the length of known notifications before accessing anything
behind the 8th byte.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class
To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().
As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.
Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check for the required out endpoint to avoid dereferencing
a NULL-pointer in mce_request_packet should a malicious device lack such
an endpoint. Note that this path is hit during probe.
Fixes: 66e89522aff7 ("V4L/DVB: IR: add mceusb IR receiver driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: using mce_dbg() instead of dev_dbg()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.
Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Source:
(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773 /* We don't need to check interfaces that are
1774 * disabled for runtime PM. Either they are unbound
1775 * or else their drivers don't support autosuspend
1776 * and so they are permanently active.
1777 */
1778 if (intf->dev.power.disable_depth)
1779 continue;
1780 if (atomic_read(&intf->dev.power.usage_count) > 0)
1781 return -EBUSY;
1782 w |= intf->needs_remote_wakeup;
Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().
To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...
Provide two solutions for the problem.
- Only trigger the hub event queue if communication with the hub
is successful.
- After a suspend failure, only resume already suspended interfaces
if the communication with the device is still possible.
Each of the changes fixes the observed problem. Use both to improve
robustness.
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: a1030e92c150 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device") Cc: Daniel Drake <dsd@gentoo.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes an issue that kernel panic happens when DMA is enabled
and we press enter key while the kernel booting on the serial console.
* An interrupt may occur after sci_request_irq().
* DMA transfer area is initialized by setup_timer() in sci_request_dma()
and used in interrupt.
If an interrupt occurred between sci_request_irq() and setup_timer() in
sci_request_dma(), DMA transfer area has not been initialized yet.
So, this patch changes the order of sci_request_irq() and
sci_request_dma().
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This device is available under different marketing names:
WLM-20U2 - Wireless USB Dongle for Toshiba TVs
GN-1080 - Wireless LAN Module for Toshiba MFPs.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This device is a dongle made by Philips to enhance their TVs with wireless capabilities,
but works flawlessly on any upstream kernel, provided that the ath9k_htc module is attached to it.
It's correctly recognized by lsusb as "0471:209e Philips (or NXP) PTA01 Wireless Adapter" and the
patch has been tested on real hardware.
Signed-off-by: Leon Nardella <leon.nardella@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Roger says, Ubiquiti produce 2 versions of their WiFiStation USB adapter. One
has an internal antenna, the other has an external antenna and
name suffix EXT. They have separate USB ids and in distribution
openSUSE 12.2 (kernel 3.4.6), file /usr/share/usb.ids shows:
Add b002 Ubiquiti WiFiStation in the PID/VID list.
Reported-by: Roger Price <ath9k@rogerprice.org> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Ryan Roper <ryan.roper@gmail.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver uses a relatively large data structure on the stack, which
showed up on my radar as we get a warning with the "latent entropy"
GCC plugin:
drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
The warning is usually hidden as we raise the warning limit to 2048
when the plugin is enabled, but I'd like to lower that again in the
future, and making this function smaller helps to do that without
build regressions.
Further analysis shows that putting an 'i2c_client' structure on
the stack is not really supported, as the embedded 'struct device'
is not initialized here, and we are only saved by the fact that
the function that is called here does not use the pointer at all.
Fixes: d855497edbfb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
page_flip_completed() dereferences 'work' variable after executing
queue_work(). This is not safe as the 'work' item might be already freed
by queued work:
snd_timer_user_tselect() reallocates the queue buffer dynamically, but
it forgot to reset its indices. Since the read may happen
concurrently with ioctl and snd_timer_user_tselect() allocates the
buffer via kmalloc(), this may lead to the leak of uninitialized
kernel-space data, as spotted via KMSAN:
BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10
CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x143/0x1b0 lib/dump_stack.c:52
kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007
kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086
copy_to_user ./arch/x86/include/asm/uaccess.h:725
snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004
do_loop_readv_writev fs/read_write.c:716
__do_readv_writev+0x94c/0x1380 fs/read_write.c:864
do_readv_writev fs/read_write.c:894
vfs_readv fs/read_write.c:908
do_readv+0x52a/0x5d0 fs/read_write.c:934
SYSC_readv+0xb6/0xd0 fs/read_write.c:1021
SyS_readv+0x87/0xb0 fs/read_write.c:1018
This patch adds the missing reset of queue indices. Together with the
previous fix for the ioctl/read race, we cover the whole problem.
Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The read from ALSA timer device, the function snd_timer_user_tread(),
may access to an uninitialized struct snd_timer_user fields when the
read is concurrently performed while the ioctl like
snd_timer_user_tselect() is invoked. We have already fixed the races
among ioctls via a mutex, but we seem to have forgotten the race
between read vs ioctl.
This patch simply applies (more exactly extends the already applied
range of) tu->ioctl_lock in snd_timer_user_tread() for closing the
race window.
Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When limiting the argv/envp strings during exec to 1/4 of the stack limit,
the storage of the pointers to the strings was not included. This means
that an exec with huge numbers of tiny strings could eat 1/4 of the stack
limit in strings and then additional space would be later used by the
pointers to the strings.
For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721
single-byte strings would consume less than 2MB of stack, the max (8MB /
4) amount allowed, but the pointers to the strings would consume the
remaining additional stack space (1677721 * 4 == 6710884).
The result (1677721 + 6710884 == 8388605) would exhaust stack space
entirely. Controlling this stack exhaustion could result in
pathological behavior in setuid binaries (CVE-2017-1000365).
[akpm@linux-foundation.org: additional commenting from Kees] Fixes: b6a2fea39318 ("mm: variable length argument support") Link: http://lkml.kernel.org/r/20170622001720.GA32173@beast Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qualys Security Advisory <qsa@qualys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: use ACCESS_ONCE() instead of READ_ONCE()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.
Reported-By: Roee Hay <roee.hay@hcl.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Rather than constructing a local structure instance on the stack, fill
the fields directly on the shared ring, just like other backends do.
Build on the fact that all response structure flavors are actually
identical (the old code did make this assumption too).
This is XSA-216.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is
disallowed. However, on x86, the first 1MB was always allowed for BIOS
and similar things, regardless of it actually being System RAM. It was
possible for heap to end up getting allocated in low 1MB RAM, and then
read by things like x86info or dd, which would trip hardened usercopy:
This changes the x86 exception for the low 1MB by reading back zeros for
System RAM areas instead of blindly allowing them. More work is needed to
extend this to mmap, but currently mmap doesn't go through usercopy, so
hardened usercopy won't Oops the kernel.
Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Kees Cook <keescook@chromium.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We dereference "skb" to get "skb->len" so we should probably do that
step before freeing the skb.
Fixes: eea221ce4880 ("tc35815 driver update (take 2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: cc28a20e77b2 ("introduce cx82310_eth: Conexant CX82310-based ADSL router USB ethernet driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Hughes <james.hughes@raspberrypi.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Hughes <james.hughes@raspberrypi.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AP/AP_VLAN modes don't accept any real 802.11 multicast data
frames, but since they do need to accept broadcast management
frames the same is currently permitted for data frames. This
opens a security problem because such frames would be decrypted
with the GTK, and could even contain unicast L3 frames.
Since the spec says that ToDS frames must always have the BSSID
as the RA (addr1), reject any other data frames.
The problem was originally reported in "Predicting, Decrypting,
and Abusing WPA2/802.11 Group Keys" at usenix
https://www.usenix.org/conference/usenixsecurity16/technical-sessions/presentation/vanhoef
and brought to my attention by Jouni.
Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
--
Dave, I didn't want to send you a new pull request for a single
commit yet again - can you apply this one patch as is? Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: Put the new code in an else-block since the
previous if-blocks may or may not return] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I noticed that reading the snapshot file when it is empty no longer gives a
status. It suppose to show the status of the snapshot buffer as well as how
to allocate and use it. For example:
># cat snapshot
# tracer: nop
#
#
# * Snapshot is allocated *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
What happened was that it was using the ring_buffer_iter_empty() function to
see if it was empty, and if it was, it showed the status. But that function
was returning false when it was empty. The reason was that the iter header
page was on the reader page, and the reader page was empty, but so was the
buffer itself. The check only tested to see if the iter was on the commit
page, but the commit page was no longer pointing to the reader page, but as
all pages were empty, the buffer is also.
Fixes: 651e22f2701b ("ring-buffer: Always reset iterator to reader page") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
gcc -O2 cannot always prove that the loop in acpi_power_get_inferred_state()
is enterered at least once, so it assumes that cur_state might not get
initialized:
drivers/acpi/power.c: In function 'acpi_power_get_inferred_state':
drivers/acpi/power.c:222:9: error: 'cur_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This sets the variable to zero at the start of the loop, to ensure that
there is well-defined behavior even for an empty list. This gets rid of
the warning.
The warning first showed up when the -Os flag got removed in a bug fix
patch in linux-4.11-rc5.
I would suggest merging this addon patch on top of that bug fix to avoid
introducing a new warning in the stable kernels.
Fixes: 61b79e16c68d (ACPI: Fix incompatibility with mcount-based function graph tracing) Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Userspace should not be able to do things with the "dead" key type as it
doesn't have some of the helper functions set upon it that the kernel
needs. Attempting to use it may cause the kernel to crash.
Fix this by changing the name of the type to ".dead" so that it's rejected
up front on userspace syscalls by key_get_type_from_user().
Though this doesn't seem to affect recent kernels, it does affect older
ones, certainly those prior to:
commit c06cfb08b88dfbe13be44a69ae2fdc3a7c902d81
Author: David Howells <dhowells@redhat.com>
Date: Tue Sep 16 17:36:06 2014 +0100
KEYS: Remove key_type::match in favour of overriding default by match_preparse
which went in before 3.18-rc1.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function
graph tracing and then suspend to RAM, it will triple fault and reboot when
it resumes.
The first fault happens when booting a secondary CPU:
The early head_32.S code calls into load_ucode_ap(), which has an an
ftrace hook, so it calls prepare_ftrace_return(), which calls
ftrace_graph_is_dead(), which tries to access the global
'kill_ftrace_graph' variable with a virtual address, causing a fault
because the CPU is still in real mode.
The fix is to add a check in prepare_ftrace_return() to make sure it's
running in protected mode before continuing. The check makes sure the
stack pointer is a virtual kernel address. It's a bit of a hack, but
it's not very intrusive and it works well enough.
For reference, here are a few other (more difficult) ways this could
have potentially been fixed:
- Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging
is enabled. (No idea what that would break.)
- Track down load_ucode_ap()'s entire callee tree and mark all the
functions 'notrace'. (Probably not realistic.)
- Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu()
or __cpu_up(), and ensure that the pause facility can be queried from
real mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net> Cc: linux-acpi@vger.kernel.org Cc: Borislav Petkov <bp@alien8.de> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.
Reported-by: GSR <gsr.bugs@infernal-iceberg.com> Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978 Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...) Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e39 ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
KGDB is a kernel debug stub and it can't be used to debug userland as it
can only safely access kernel memory.
On MIPS however KGDB has always got the register state of sleeping
processes from the userland register context at the beginning of the
kernel stack. This is meaningless for kernel threads (which never enter
userland), and for user threads it prevents the user seeing what it is
doing while in the kernel:
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) 0x0000000000000000 in ?? ()
2 Thread 1 (init) 0x000000007705c4b4 in ?? ()
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Get the register state instead from the (partial) kernel register
context stored in the task's thread_struct for resume() to restore. All
threads now correctly appear to be in context_switch():
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Call clobbered registers which aren't saved and exception registers
(BadVAddr & Cause) which can't be easily determined without stack
unwinding are reported as 0. The PC is taken from the return address,
such that the state presented matches that found immediately after
returning from resume().
Fixes: 8854700115ec ("[MIPS] kgdb: add arch support for the kernel's kgdb core") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15829/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The vsyscall32 sysctl can racy against a concurrent fork when it switches
from disabled to enabled:
arch_setup_additional_pages()
if (vdso32_enabled)
--> No mapping
sysctl.vsysscall32()
--> vdso32_enabled = true
create_elf_tables()
ARCH_DLINFO_IA32
if (vdso32_enabled) {
--> Add VDSO entry with NULL pointer
Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for
the newly forked process or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mathias Krause <minipli@googlemail.com> Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2: change the flag passed to ARCH_DLINFO_IA32()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pppol2tp_getsockopt() doesn't take into account the error code returned
by pppol2tp_tunnel_getsockopt() or pppol2tp_session_getsockopt(). If
error occurs there, pppol2tp_getsockopt() continues unconditionally and
reports erroneous values.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pppol2tp_setsockopt() unconditionally overwrites the error value
returned by pppol2tp_tunnel_setsockopt() or
pppol2tp_session_setsockopt(), thus hiding errors from userspace.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against
__TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end
of a PTRACE_LISTEN, this can wake the task /after/ the check against
__TASK_TRACED, but before the reset of state to TASK_TRACED. This
causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup
against TRACED while the task is still on the rq wake_list, corrupting
it.
Oleg said:
"The kernel can crash or this can lead to other hard-to-debug problems.
In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced()
assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the
contract. Obviusly it is very wrong to manipulate task->state if this
task is already running, or WAKING, or it sleeps again"
[akpm@linux-foundation.org: coding-style fixes] Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL") Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com Signed-off-by: Ben Segall <bsegall@google.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Reported-by: Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.2: use integer literal instead of U32_MAX] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Connecting to the backend isn't working reliably in xen-fbfront: in
case XenbusStateInitWait of the backend has been missed the backend
transition to XenbusStateConnected will trigger the connected state
only without doing the actions required when the backend has
connected.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Take a reference on the sessions returned by l2tp_session_find_nth()
(and rename it l2tp_session_get_nth() to reflect this change), so that
caller is assured that the session isn't going to disappear while
processing it.
For procfs and debugfs handlers, the session is held in the .start()
callback and dropped in .show(). Given that pppol2tp_seq_session_show()
dereferences the associated PPPoL2TP socket and that
l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to
call the session's .ref() callback to prevent the socket from going
away from under us.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Fixes: 0ad6614048cf ("l2tp: Add debugfs files for dumping l2tp debug info") Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the past, there was only one load-with-reservation instruction,
lwarx, and if a program attempted a lwarx on a misaligned address, it
would take an alignment interrupt and the kernel handler would emulate
it as though it was lwzx, which was not really correct, but benign since
it is loading the right amount of data, and the lwarx should be paired
with a stwcx. to the same address, which would also cause an alignment
interrupt which would result in a SIGBUS being delivered to the process.
We now have 5 different sizes of load-with-reservation instruction. Of
those, lharx and ldarx cause an immediate SIGBUS by luck since their
entries in aligninfo[] overlap instructions which were not fixed up, but
lqarx overlaps with lhz and will be emulated as such. lbarx can never
generate an alignment interrupt since it only operates on 1 byte.
To straighten this out and fix the lqarx case, this adds code to detect
the l[hwdq]arx instructions and return without fixing them up, resulting
in a SIGBUS being delivered to the process.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.2: open-code get_xop()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A dump may come in the middle of another dump, modifying its dump
structure members. This race condition will result in NULL pointer
dereference in kernel. So add a lock to prevent that race.
Fixes: 83321d6b9872 ("[AF_KEY]: Dump SA/SP entries non-atomically") Signed-off-by: Yuejie Shi <syjcnss@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
[bwh: Backported to 3.2:
- pfkey_dump() doesn't support filters
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Once upon a time back in 2009, a work-around was added to support
the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login
did not propose nor respond to MaxBurstLength, FirstBurstLength,
DefaultTime2Wait and DefaultTime2Retain keys.
The work-around in iscsi_check_proposer_for_optional_reply()
allowed the missing keys to be proposed, but did not require
waiting for a response before moving to full feature phase
operation. This allowed GlobalSAN v3.3 to work out-of-the
box, and for many years we didn't run into login interopt
issues with any other initiators..
Until recently, when Martin tried a QLogic 57840S iSCSI Offload
HBA on Windows 2016 which completed login, but subsequently
failed with:
Got unknown iSCSI OpCode: 0x43
The issue was QLogic MSFT side did not propose DefaultTime2Wait +
DefaultTime2Retain, so LIO proposes them itself, and immediately
transitions to full feature phase because of the GlobalSAN hack.
However, the QLogic MSFT side still attempts to respond to
DefaultTime2Retain + DefaultTime2Wait, even though LIO has set
ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT
in last login response.
So while the QLogic MSFT side should have been proposing these
two keys to start, it was doing the correct thing per RFC-3720
attempting to respond to proposed keys before transitioning to
full feature phase.
All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541)
does correctly propose the four keys during login, making the
original work-around moot.
So in order to allow QLogic MSFT to run unmodified as-is, go
ahead and drop this long standing work-around.
Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Callers of l2tp_nl_session_find() need to hold a reference on the
returned session since there's no guarantee that it isn't going to
disappear from under them.
Relying on the fact that no l2tp netlink message may be processed
concurrently isn't enough: sessions can be deleted by other means
(e.g. by closing the PPPOL2TP socket of a ppp pseudowire).
l2tp_nl_cmd_session_delete() is a bit special: it runs a callback
function that may require a previous call to session->ref(). In
particular, for ppp pseudowires, the callback is l2tp_session_delete(),
which then calls pppol2tp_session_close() and dereferences the PPPOL2TP
socket. The socket might already be gone at the moment
l2tp_session_delete() calls session->ref(), so we need to take a
reference during the session lookup. So we need to pass the do_ref
variable down to l2tp_session_get() and l2tp_session_get_by_ifname().
Since all callers have to be updated, l2tp_session_find_by_ifname() and
l2tp_nl_session_find() are renamed to reflect their new behaviour.
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
l2tp_session_create() relies on its caller for checking for duplicate
sessions. This is racy since a session can be concurrently inserted
after the caller's verification.
Fix this by letting l2tp_session_create() verify sessions uniqueness
upon insertion. Callers need to be adapted to check for
l2tp_session_create()'s return code instead of calling
l2tp_session_find().
pppol2tp_connect() is a bit special because it has to work on existing
sessions (if they're not connected) or to create a new session if none
is found. When acting on a preexisting session, a reference must be
held or it could go away on us. So we have to use l2tp_session_get()
instead of l2tp_session_find() and drop the reference before exiting.
Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support") Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: add 'pos' parameter to
hlist_for_each_entry{,_rcu}() calls] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Holding a reference on session is required before calling
pppol2tp_session_ioctl(). The session could get freed while processing the
ioctl otherwise. Since pppol2tp_session_ioctl() uses the session's socket,
we also need to take a reference on it in l2tp_session_get().
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Taking a reference on sessions in l2tp_recv_common() is racy; this
has to be done by the callers.
To this end, a new function is required (l2tp_session_get()) to
atomically lookup a session and take a reference on it. Callers then
have to manually drop this reference.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
- Drop changes to l2tp_ip6.c
- Add 'pos' parameter to hlist_for_each_entry{,_rcu}() calls
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The reference manual for the i.MX28 recommends to calculate the divisor
as
divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer
, so let's do this. For a typical setup of UARTCLK = 24 MHz and baud
rate = 115200 this changes the divisor from 6666 to 6667 and so the
actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to
115194.240 Bd (error ≅ 0.005 %).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
SDIO cards may need clock to send the card interrupt to the host.
On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch
pinging the tablet results in:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms
Where as with this patch I get:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms
Cc: Dong Aisheng <b29396@freescale.com> Cc: Ian W MORRISON <ianwmorrison@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The mesa winsys sometimes uses unimplemented parameter requests to
check for features. Remove the error message to avoid bloating the
kernel log.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>