When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.
This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.
__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.
This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.
The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().
Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.
Different versions of glibc are broken in different ways, but the short of
it is that for the time being, frsize should == bsize, and be used as the
multiple for the blocks, free, and available fields. This mirrors what is
done for NFS. The previous reporting of the page size for frsize meant
that newer glibc and df would report a very small value for the fs size.
The auth code is called from a variety of contexts, include the mon_client
(protected by the monc's mutex) and the messenger callbacks (currently
protected by nothing). Avoid chaos by protecting all auth state with a
mutex. Nothing is blocking, so this should be simple and lightweight.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use wrapper functions that check whether the auth op exists so that callers
do not need a bunch of conditional checks. Simplifies the external
interface.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the messenger calls out to a get_authorizer con op, which will
create a new authorizer if it doesn't yet have one. In the meantime, when
we rotate our service keys, the authorizer doesn't get updated. Eventually
it will be rejected by the server on a new connection attempt and get
invalidated, and we will then rebuild a new authorizer, but this is not
ideal.
Instead, if we do have an authorizer, call a new update_authorizer op that
will verify that the current authorizer is using the latest secret. If it
is not, we will build a new one that does. This avoids the transient
failure.
This fixes one of the sorry sequence of events for bug
http://tracker.ceph.com/issues/4282
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were invalidating the authorizer by removing the ticket handler
entirely. This was effective in inducing us to request a new authorizer,
but in the meantime it mean that any authorizer we generated would get a
new and initialized handler with secret_id=0, which would always be
rejected by the server side with a confusing error message:
auth: could not find secret_id=0
cephx: verify_authorizer could not get service secret for service osd secret_id=0
Instead, simply clear the validity field. This will still induce the auth
code to request a new secret, but will let us continue to use the old
ticket in the meantime. The messenger code will probably continue to fail,
but the exponential backoff will kick in, and eventually the we will get a
new (hopefully more valid) ticket from the mon and be able to continue.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We maintain a counter of failed auth attempts to allow us to retry once
before failing. However, if the second attempt succeeds, the flag isn't
cleared, which makes us think auth failed again later when the connection
resets for other reasons (like a socket error).
This is one part of the sorry sequence of events in bug
http://tracker.ceph.com/issues/4282
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes. As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.
This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage. This patch introduces
migration_entry_wait_huge() to solve this.
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.
This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map(). This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.
This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: Rafael Aquini <aquini@redhat.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Shaohua Li <shli@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC
Egbert Eich fixed a long-standing bug where we simply used a
non-working i2c controller to read the EDID for SDVO-LVDS panels.
Unfortunately some machines seem to not be able to cope with the mode
provided in the EDID. Specifically they seem to not be able to cope
with a 4x pixel mutliplier instead of a 2x one, which seems to have
been worked around by slightly changing the panels native mode in the
VBT so that the dotclock is just barely above 50MHz.
Since it took forever to notice the breakage it's fairly safe to
assume that at least for SDVO-LVDS panels the VBT contains fairly sane
data. So just switch around the order and use VBT modes first.
v2: Also add EDID modes just in case, and spell Egbert correctly.
v3: Elaborate a bit more about what's going on on Chris' machine.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65524 Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Egbert Eich <eich@suse.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below. It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive,
the mutex isn't.
Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
[...]
acu D 0000000000000001 0 3246 3191 0x00000080
Call Trace:
schedule+0x29/0x70
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x17b/0x220
mutex_lock+0x2b/0x50
cciss_unlocked_open+0x2f/0x110 [cciss]
__blkdev_get+0xd3/0x470
blkdev_get+0x5c/0x1e0
register_disk+0x182/0x1a0
add_disk+0x17c/0x310
cciss_add_disk+0x13a/0x170 [cciss]
cciss_update_drive_info+0x39b/0x480 [cciss]
rebuild_lun_table+0x258/0x370 [cciss]
cciss_ioctl+0x34f/0x470 [cciss]
do_ioctl+0x49/0x70 [cciss]
__blkdev_driver_ioctl+0x28/0x30
blkdev_ioctl+0x200/0x7b0
block_ioctl+0x3c/0x40
do_vfs_ioctl+0x89/0x350
SyS_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
This mutex usage was added into the ioctl path when the big kernel lock
was removed. As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit f96972f2dc63 ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russ Anderson <rja@sgi.com> Cc: Robin Holt <holt@sgi.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Robin Holt <holt@sgi.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russ Anderson <rja@sgi.com> Cc: Robin Holt <holt@sgi.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com> Reported-by: Kevin Hilman <khilman@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ceph's encode_caps_cb() worked hard to not call __page_cache_alloc()
while holding a lock, but it's spoiled because ceph_pagelist_addpage()
always calls kmap(), which might sleep. Here's the result:
In his review, Alex Elder mentioned that he hadn't checked that
num_fcntl_locks and num_flock_locks were properly decoded on the
server side, from a le32 over-the-wire type to a cpu type.
I checked, and AFAICS it is done; those interested can consult
Locker::_do_cap_update()
in src/mds/Locker.cc and src/include/encoding.h in the Ceph server
code (git://github.com/ceph/ceph).
I also checked the server side for flock_len decoding, and I believe
that also happens correctly, by virtue of having been declared
__le32 in struct ceph_mds_cap_reconnect, in src/include/ceph_fs.h.
Signed-off-by: Jim Schutt <jaschut@sandia.gov> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As ftrace_filter_lseek is now used with ftrace_pid_fops, it needs to
be moved out of the #ifdef CONFIG_DYNAMIC_FTRACE section as the
ftrace_pid_fops is defined when DYNAMIC_FTRACE is not.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Namhyung Kim <namhyung@kernel.org>
[ lizf: adjust context ] Signed-off-by: Li Zefan <lizefan@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently set_ftrace_pid and set_graph_function files use seq_lseek
for their fops. However seq_open() is called only for FMODE_READ in
the fops->open() so that if an user tries to seek one of those file
when she open it for writing, it sees NULL seq_file and then panic.
It can be easily reproduced with following command:
$ cd /sys/kernel/debug/tracing
$ echo 1234 | sudo tee -a set_ftrace_pid
In this example, GNU coreutils' tee opens the file with fopen(, "a")
and then the fopen() internally calls lseek().
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
... as being guest triggerable (e.g. by invoking
XEN_PCI_OP_enable_msi{,x} on a device not being MSI/MSI-X capable).
This is CVE-2013-0231 / XSA-43.
Also make the two messages uniform in both their wording and severity.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[stable tree: Added two extra #include files] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
Signed-off-by: Egbert Eich <eich@suse.de> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When GPU acceleration is disabled, drm_vblank_cleanup() will free the
vblank-related data, such as vblank_refcount, vblank_inmodeset, etc.
But we found that drm_vblank_post_modeset() may be called after the
cleanup, which use vblank_refcount and vblank_inmodeset. And this will
cause a kernel panic.
Fix this by return immediately if dev->num_crtcs is zero. This is the
same thing that drm_vblank_pre_modeset() does.
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected
as LM84. Strengthen detection sufficiently enough to avoid this misdetection.
Also improve detection for ADM1021.
Modeled after chip detection code in sensors-detect command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").
The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.
Reported-by: Robert Knight <knight@princeton.edu> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Tested-by: Robert Knight <knight@princeton.edu> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661 Signed-off-by: Ash Willis <ashwillis@programmer.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501 Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Joseph Salisbury <joseph.salisbury@canonical.com> CC: Tim Richardson <tim@tim-richardson.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 214916f2e ("USB: visor: reimplement
using generic framework") which broke initialisation of Treo/Kyocera
devices that re-mapped bulk-in endpoints.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB audio driver spews an error message when probing Logitech HD
webcam c270:
ALSA mixer.c:1300 usb_audio: Warning! Unlikely big volume range (=6144), cval->res is probably wrong.
ALSA mixer.c:1304 usb_audio: [5] FU [Mic Capture Volume] ch = 1, val = 1536/7680/1
Obviously the device needs a fixed volume resolution (cval->res = 384)
like other Logitech devices.
Commit 927c9423dd5f2d1c0b93d5e694ab84b4a5559713 (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
If for whatever reason we fall into fail path in xhci_mem_init()
before bw table gets initialized we may access the uninitialized lists
in xhci_mem_cleanup().
Check for bw table before traversing lists in cleanup routine.
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Reported-by: Sergey Dyasly <dserrg@gmail.com> Tested-by: Sergey Dyasly <dserrg@gmail.com> Signed-off-by: Vladimir Murzin <murzin.v@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that we fail on xhci_mem_init, just before doing
the INIT_LIST_HEAD, and calling xhci_mem_cleanup.
Problem is that, the list_for_each_entry_safe macro, assumes
list heads are initialized (not NULL), and dereferences their 'next'
pointer, causing a kernel panic if this is not yet initialized.
Let's protect from that by moving inits to the beginning.
Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP
Hardware) was a workaround for systems using the SN65LVPE502CP,
controller, but it introduced a bug in resume from hibernate.
The fix created a timer, comp_mode_recovery_timer, which is deleted from
a timer list when xhci_suspend() is called. However, the hibernate image,
including the timer list containing the comp_mode_recovery_timer, had
already been saved before the timer was deleted.
Upon resume from hibernate, the list containing the comp_mode_recovery_timer
is restored from the image saved to disk, and xhci_resume(), assuming that
the timer had been deleted by xhci_suspend(), makes a call to
compliance_mode_recoery_timer_init(), which creates a new instance of the
comp_mode_recovery_timer and attempts to place it into the same list in which
it is already active, thus corrupting the list during the list_add() call.
At this point, a call trace is emitted indicating the list corruption.
Soon afterward, the system locks up, the watchdog times out, and the
ensuing NMI crashes the system.
The problem did not occur when resuming from suspend. In suspend, the
image in RAM remains exactly as it was when xhci_suspend() deleted the
comp_mode_recovery_timer, so there is no problem when xhci_resume()
creates a new instance of this timer and places it in the still empty
list.
This patch avoids the problem by deleting the timer in xhci_resume()
when resuming from hibernate. Now xhci_resume() can safely make the
call to create a new instance of this timer, whether returning from
suspend or hibernate.
Thanks to Alan Stern for his help with understanding the problem.
[Sarah reworked this patch to cover the case where the xHCI restore
register operation fails, and (temp & STS_SRE) is true (and we re-init
the host, including re-init for the compliance mode), but hibernate is
false. The original patch would have caused list corruption in this
case.]
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Tony Camuso <tcamuso@redhat.com> Tested-by: Tony Camuso <tcamuso@redhat.com> Acked-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the latest V-series bios DMI_PRODUCT_VERSION does not contain
the string Lenovo or Thinkpad, but is set to the model number, this
causes the thinkpad_acpi module to fail to load. Recognize laptop
as Lenovo using DMI_BIOS_VENDOR instead, which is set to Lenovo.
Test on V490u
=============
== After the patch ==
[ 1350.295757] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[ 1350.295760] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 1350.295761] thinkpad_acpi: ThinkPad BIOS H7ET21WW (1.00 ), EC unknown
[ 1350.295763] thinkpad_acpi: Lenovo LENOVO, model LV5DXXX
[ 1350.296086] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[ 1350.296694] thinkpad_acpi: radio switch found; radios are enabled
[ 1350.296703] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
[ 1350.306466] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 1350.307082] Registered led device: tpacpi::thinklight
[ 1350.307215] Registered led device: tpacpi::power
[ 1350.307255] Registered led device: tpacpi::standby
[ 1350.307294] Registered led device: tpacpi::thinkvantage
[ 1350.308160] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[ 1350.308333] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[ 1350.312287] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input14
== Before the patch ==
sudo modprobe thinkpad_acpi
FATAL: Error inserting thinkpad_acpi (/lib/modules/3.2.0-27-generic/kernel/drivers/platform/x86/thinkpad_acpi.ko): No such device
Test on B485
=============
This patch was also test in a B485 where the thinkpad_acpi module does not
have any issues loading. But, I tested it to make sure this patch does not
break on already functioning models of Lenovo products.
[13486.746359] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[13486.746364] thinkpad_acpi: http://ibm-acpi.sf.net/
[13486.746368] thinkpad_acpi: ThinkPad BIOS HJET15WW(1.01), EC unknown
[13486.746373] thinkpad_acpi: Lenovo Lenovo LB485, model 814TR01
[13486.747300] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[13486.752435] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[13486.752883] Registered led device: tpacpi::thinklight
[13486.752915] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[13486.753216] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[13486.757147] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input15
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Shuduo Sang <shuduo.sang@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latest GCC 4.8 does some more checking on type attributes that
break the build for ARCH=um -> fill them in. Specifically, the
"asmlinkage" attributes is now tested for consistency.
Signed-off-by: Martin Pelikan <pelikan@storkhole.cz> Link: http://lkml.kernel.org/r/1339269731-10772-1-git-send-email-pelikan@storkhole.cz Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Bernhard M. Wiedemann <bwiedemann@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Work around an IOMMU hardware bug where clearing the
EVT_INT or PPR_INT bit in the status register may race with
the hardware trying to set it again. When not handled the
bit might not be cleared and we lose all future event or ppr
interrupts.
Current driver does not clear the IOMMU event log interrupt bit
in the IOMMU status register after processing an interrupt.
This causes the IOMMU hardware to generate event log interrupt only once.
This has been observed in both IOMMU v1 and V2 hardware.
This patch clears the bit by writing 1 to bit 1 of the IOMMU
status register (MMIO Offset 2020h)
Signed-off-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes races uncovered by xfstests testcase 068.
One race is the result of jfs_sync() trying to write a sync point to the
journal after it has been frozen (or possibly in the process). Since
freezing sync's the journal, there is no need to write a sync point so
we simply want to return.
The second involves jfs_write_inode() being called on a deleted inode.
It calls jfs_flush_journal which is held up by the jfs_commit thread
doing the final iput on the same deleted inode, which itself is
waiting for the I_SYNC flag to be cleared. jfs_write_inode need not
do anything when i_nlink is zero, which is the easy fix.
Reported-by: Michael L. Semon <mlsemon35@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids any other hardirq handler seeing a very stale jiffies
value immediately after wakeup from a long idle period. The one
observable symptom of this was a USB keyboard, with software keyboard
repeat, which would always repeat a key immediately that it was
pressed. This is due to the key press waking the guest, the key
handler immediately runs, sees an old jiffies value, and then that
jiffies value significantly updated, before the key is unpressed.
Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Keir Fraser <keir.fraser@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The present code does not wait for the SCC to finish resetting itself
before trying to initialise the device. The result is that the SCC
interrupt sources become enabled (if they weren't already). This leads to
an early boot crash (unexpected interrupt) given CONFIG_EARLY_PRINTK. Fix
this by adding a delay. A successful reset disables the interrupt sources.
Also, after the reset for channel A setup, the SCC then gets a second
reset for channel B setup which leaves channel A uninitialised again. Fix
this by performing the reset only once.
libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.
This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.
Log output of the bridge being hot-plugged with an ATAPI drive:
[ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
[ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
[ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
[ 9631.212939] ata1: hard resetting link
[ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33
[ 9632.106407] ata1.00: applying bridge limits
[ 9632.108151] ata1.00: configured for UDMA/33
[ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
[ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9637.105335] ata1: hard resetting link
[ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9638.047878] ata1.00: configured for UDMA/33
[ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
[ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
[ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
[ 9643.044979] ata1: hard resetting link
[ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9643.987471] ata1.00: configured for UDMA/33
[ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
[ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9648.984619] ata1.00: disabled
[ 9649.000593] ata1: hard resetting link
[ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9649.955864] ata1: EH complete
With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:
Consider the case where we have a very short ip= string in the original
mount options, and when we chase a referral we end up with a very long
IPv6 address. Be sure to allow for that possibility when estimating the
size of the string to allocate.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XFS has failed to kill suid/sgid bits correctly when truncating
files of non-zero size since commit c4ed4243 ("xfs: split
xfs_setattr") introduced in the 3.1 kernel. Fix it.
Fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a key was larger than 64 bytes, as checked by iscsi_check_key(), the
error response packet, generated by iscsi_add_notunderstood_response(),
would still attempt to copy the entire key into the packet, overflowing
the structure on the heap.
Remote preauthentication kernel memory corruption was possible if a
target was configured and listening on the network.
We should not use set_pmd_at to update pmd_t with pgtable_t pointer.
set_pmd_at is used to set pmd with huge pte entries and architectures
like ppc64, clear few flags from the pte when saving a new entry.
Without this change we observe bad pte errors like below on ppc64 with
THP enabled.
A panic can be caused by simply cat'ing /proc/<pid>/smaps while an
application has a VM_PFNMAP range. It happened in-house when a
benchmarker was trying to decipher the memory layout of his program.
/proc/<pid>/smaps and similar walks through a user page table should not
be looking at VM_PFNMAP areas.
Certain tests in walk_page_range() (specifically split_huge_page_pmd())
assume that all the mapped PFN's are backed with page structures. And
this is not usually true for VM_PFNMAP areas. This can result in panics
on kernel page faults when attempting to address those page structures.
There are a half dozen callers of walk_page_range() that walk through a
task's entire page table (as N. Horiguchi pointed out). So rather than
change all of them, this patch changes just walk_page_range() to ignore
VM_PFNMAP areas.
The logic of hugetlb_vma() is moved back into walk_page_range(), as we
want to test any vma in the range.
VM_PFNMAP areas are used by:
- graphics memory manager gpu/drm/drm_gem.c
- global reference unit sgi-gru/grufile.c
- sgi special memory char/mspec.c
- and probably several out-of-tree modules
[akpm@linux-foundation.org: remove now-unused hugetlb_vma() stub] Signed-off-by: Cliff Wickman <cpw@sgi.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David Sterba <dsterba@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Reported-by: Chris Wedgwood <cw@f00f.org> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 751efd8610d3 ("mmu_notifier_unregister NULL Pointer deref and
multiple ->release()") breaks the fix 3ad3d901bbcf ("mm: mmu_notifier:
fix freed page still mapped in secondary MMU").
Since hlist_for_each_entry_rcu() is changed now, we can not revert that
patch directly, so this patch reverts the commit and simply fix the bug
spotted by that patch
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result
of a filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
This can be fixed by using hlist_del_init_rcu instead of hlist_del_rcu.
The another issue spotted in the commit is "multiple ->release()
callouts", we needn't care it too much because it is really rare (e.g,
can not happen on kvm since mmu-notify is unregistered after
exit_mmap()) and the later call of multiple ->release should be fast
since all the pages have already been released by the first call.
Anyway, this issue should be fixed in a separate patch.
-stable suggestions: Any version that has commit 751efd8610d3 need to be
backported. I find the oldest version has this commit is 3.0-stable.
nilfs2: fix issue of nilfs_set_page_dirty for page at EOF boundary
DESCRIPTION:
There are use-cases when NILFS2 file system (formatted with block size
lesser than 4 KB) can be remounted in RO mode because of encountering of
"broken bmap" issue.
The issue was reported by Anthony Doggett <Anthony2486@interfaces.org.uk>:
"The machine I've been trialling nilfs on is running Debian Testing,
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc
version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2), but I've
also reproduced it (identically) with Debian Unstable amd64 and Debian
Experimental (using the 3.8-trunk kernel). The problematic partitions
were formatted with "mkfs.nilfs2 -b 1024 -B 8192"."
SYMPTOMS:
(1) System log contains error messages likewise:
(2) The NILFS2 file system is remounted in RO mode.
REPRODUSING PATH:
(1) Create volume group with name "unencrypted" by means of vgcreate utility.
(2) Run script (prepared by Anthony Doggett <Anthony2486@interfaces.org.uk>):
The error message "NILFS error (device dm-17): nilfs_bmap_assign: broken
bmap (inode number=28)" takes place because of trying to get block
number for third block of the file with logical offset #3072 bytes. As
it is possible to see from above output, the file has 60 bytes of the
whole size. So, it is enough one block (1 KB in size) allocation for
the whole file. Trying to operate with several blocks instead of one
takes place because of discovering several dirty buffers for this file
in nilfs_segctor_scan_file() method.
The root cause of this issue is in nilfs_set_page_dirty function which
is called just before writing to an mmapped page.
When nilfs_page_mkwrite function handles a page at EOF boundary, it
fills hole blocks only inside EOF through __block_page_mkwrite().
The __block_page_mkwrite() function calls set_page_dirty() after filling
hole blocks, thus nilfs_set_page_dirty function (=
a_ops->set_page_dirty) is called. However, the current implementation
of nilfs_set_page_dirty() wrongly marks all buffers dirty even for page
at EOF boundary.
As a result, buffers outside EOF are inconsistently marked dirty and
queued for write even though they are not mapped with nilfs_get_block
function.
FIX:
This modifies nilfs_set_page_dirty() not to mark hole blocks dirty.
Thanks to Vyacheslav Dubeyko for his effort on analysis and proposals
for this issue.
Many callers of the wait_event_timeout() and
wait_event_interruptible_timeout() expect that the return value will be
positive if the specified condition becomes true before the timeout
elapses. However, at the moment this isn't guaranteed. If the wake-up
handler is delayed enough, the time remaining until timeout will be
calculated as 0 - and passed back as a return value - even if the
condition became true before the timeout has passed.
Fix this by returning at least 1 if the condition becomes true. This
semantic is in line with what wait_for_condition_timeout() does; see
commit bb10ed09 ("sched: fix wait_for_completion_timeout() spurious
failure under heavy load").
Daniel said "We have 3 instances of this bug in drm/i915. One case even
where we switch between the interruptible and not interruptible
wait_event_timeout variants, foolishly presuming they have the same
semantics. I very much like this."
One such bug is reported at
https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Jens Axboe <axboe@kernel.dk> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Dave Jones <davej@redhat.com> Cc: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between klist_remove and klist_release. klist_remove
uses a local var waiter saved on stack. When klist_release calls
wake_up_process(waiter->process) to wake up the waiter, waiter might run
immediately and reuse the stack. Then, klist_release calls
list_del(&waiter->list) to change previous
wait data and cause prior waiter thread corrupt.
Page 'new' during MIGRATION can't be flushed with flush_cache_page().
Using flush_cache_page(vma, addr, pfn) is justified only if the page is
already placed in process page table, and that is done right after
flush_cache_page(). But without it the arch function has no knowledge
of process PTE and does nothing.
Besides that, flush_cache_page() flushes an application cache page, but
the kernel has a different page virtual address and dirtied it.
Replace it with flush_dcache_page(new) which is the proper usage.
The old page is flushed in try_to_unmap_one() before migration.
This bug takes place in Sead3 board with M14Kc MIPS CPU without cache
aliasing (but Harvard arch - separate I and D cache) in tight memory
environment (128MB) each 1-3days on SOAK test. It fails in cc1 during
kernel build (SIGILL, SIGBUS, SIGSEG) if CONFIG_COMPACTION is switched
ON.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: Leonid Yegoshin <yegoshin@mips.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Michal Hocko <mhocko@suse.cz> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Bryan Wu <cooloney@gmail.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable KW_PCIE1 on QNAP TS-11x/TS-21x devices as newer revisions
(rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1. Thanks
to Marek Vasut for identifying this issue!
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Tested-by: Marek Vasut <marex@denx.de> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last time we found there is lock/unlock bug in ocfs2_file_aio_write, and
then we did a thorough search for all lock resources in
ocfs2_inode_info, including rw, inode and open lockres and found this
bug. My kernel version is 3.0.13, and it is also in the lastest version
3.9. In ocfs2_fiemap, once ocfs2_get_clusters_nocache failed, it should
goto out_unlock instead of out, because we need release buffer head, up
read alloc sem and unlock inode.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Reviewed-by: Jie Liu <jeff.liu@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Acked-by: Sunil Mushran <sunil.mushran@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison between traced and symbol addresses is backwards: if
the traced address doesn't exactly match a symbol (which we don't
expect it to), we'll show the next symbol and the offset to it,
whereas we should show the previous symbol and the offset from it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This works much better if we don't treat protocol numbers as addresses.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's generally not safe to reset the inode ops once they've been set. In
the case where the inode was originally thought to be a directory and
then later found to be a DFS referral, this can lead to an oops when we
try to trigger an inode op on it after changing the ops to the blank
referral operations.
Reported-and-Tested-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP's virtual UHCI host controller takes a long time to suspend
(several hundred microseconds), even when no devices are attached.
This provokes a warning message from uhci-hcd in the auto-stop case.
To prevent this from happening, this patch adds a test to avoid
performing an auto-stop when the wait_for_hp quirk flag is set. The
controller will still suspend through the normal runtime PM mechanism.
And since that pathway includes a 1-ms delay, the slowness of the
virtual hardware won't matter.
This patch shortens the logic in xhci_endpoint_init() by moving common
calculations involving max_packet and max_burst outside the switch
statement, rather than repeating the same code in multiple
case-specific statements. It also replaces two usages of max_packet
which were clearly intended to be max_burst all along.
More importantly, it compensates for a common bug in high-speed bulk
endpoint descriptors. In many devices there is a bulk endpoint having
a wMaxPacketSize value smaller than 512, which is forbidden by the USB
spec. Some xHCI controllers can't handle this and refuse to accept
the endpoint. This patch changes the max_packet value to 512, which
allows the controller to use the endpoint properly.
In practice the bogus maxpacket size doesn't matter, because none of
the transfers sent via these endpoints are longer than the maxpacket
value anyway.
/drivers/usb/serial/option.c: Blacklisted Cinterion's PLxx WWAN
Interface (USB Interface 4), because it will be handled by QMI WWAN
driver. Product IDs renamed.
I meet emacs hang in start if I do the operation below:
1: echo 3 > /proc/sys/vm/drop_caches
2: emacs BigFile
3: Press CTRL-S follow 2 immediately
Then emacs hang on, CTRL-Q can't resume, the terminal
hang on, you can do nothing with this terminal except
close it.
The reason is before emacs takeover control the tty,
we use CTRL-S to XOFF it. Then when emacs takeover the
control, it may don't use the flow-control, so emacs hang.
This patch fix it.
This patch will fix a kind of strange tty relation hang problem,
I believe I meet it with vim in ssh, and also see below bug report:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=465823
Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of "offd" comes off the instance->rcv_buf[] and we used it as
the offset into an array. The problem is that we check the upper bound
but not for negative values.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two more devices that use FTDI USB-to-serial chips with new product ID's.
The devices are the Newport Conex-AGP and Conex-CC motor controllers.
(http://www.newport.com/CONEX-AGP-Integrated-Piezo-Motor-Rotation-Stages-/987623/1033/info.aspx)
(http://www.newport.com/CONEX-CC-DC-Servo-Controller-Actuators/934114/1033/info.aspx)
projects / linux-stable / log