Do not put bh when buffer_uptodate failed in ocfs2_write_block and
ocfs2_write_super_or_backup, because it will put bh in b_end_io.
Otherwise it will hit a warning "VFS: brelse: Trying to free free
buffer".
Signed-off-by: Alex Chen <alex.chen@huawei.com> Reviewed-by: Joseph Qi <joseph.qi@huawei.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Acked-by: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race window in dlm_do_recovery() between dlm_remaster_locks()
and dlm_reset_recovery() when the recovery master nearly finish the
recovery process for a dead node. After the master sends FINALIZE_RECO
message in dlm_remaster_locks(), another node may become the recovery
master for another dead node, and then send the BEGIN_RECO message to
all the nodes included the old master, in the handler of this message
dlm_begin_reco_handler() of old master, dlm->reco.dead_node and
dlm->reco.new_master will be set to the second dead node and the new
master, then in dlm_reset_recovery(), these two variables will be reset
to default value. This will cause new recovery master can not finish
the recovery process and hung, at last the whole cluster will hung for
recovery.
old recovery master: new recovery master:
dlm_remaster_locks()
become recovery master for
another dead node.
dlm_send_begin_reco_message()
dlm_begin_reco_handler()
{
if (dlm->reco.state & DLM_RECO_STATE_FINALIZE) {
return -EAGAIN;
}
dlm_set_reco_master(dlm, br->node_idx);
dlm_set_reco_dead_node(dlm, br->dead_node);
}
dlm_reset_recovery()
{
dlm_set_reco_dead_node(dlm, O2NM_INVALID_NODE_NUM);
dlm_set_reco_master(dlm, O2NM_INVALID_NODE_NUM);
}
will hang in dlm_remaster_locks() for
request dlm locks info
Before send FINALIZE_RECO message, recovery master should set
DLM_RECO_STATE_FINALIZE for itself and clear it after the recovery done,
this can break the race windows as the BEGIN_RECO messages will not be
handled before DLM_RECO_STATE_FINALIZE flag is cleared.
A similar race may happen between new recovery master and normal node
which is in dlm_finalize_reco_handler(), also fix it.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue was introduced by commit 800deef3f6f8 ("ocfs2: use
list_for_each_entry where benefical") in 2007 where it replaced
list_for_each with list_for_each_entry. The variable "lock" will point
to invalid data if "tmpq" list is empty and a panic will be triggered
due to this. Sunil advised reverting it back, but the old version was
also not right. At the end of the outer for loop, that
list_for_each_entry will also set "lock" to an invalid data, then in the
next loop, if the "tmpq" list is empty, "lock" will be an stale invalid
data and cause the panic. So reverting the list_for_each back and reset
"lock" to NULL to fix this issue.
Another concern is that this seemes can not happen because the "tmpq"
list should not be empty. Let me describe how.
old lock resource owner(node 1): migratation target(node 2):
image there's lockres with a EX lock from node 2 in
granted list, a NR lock from node x with convert_type
EX in converting list.
dlm_empty_lockres() {
dlm_pick_migration_target() {
pick node 2 as target as its lock is the first one
in granted list.
}
dlm_migrate_lockres() {
dlm_mark_lockres_migrating() {
res->state |= DLM_LOCK_RES_BLOCK_DIRTY;
wait_event(dlm->ast_wq, !dlm_lockres_is_dirty(dlm, res));
//after the above code, we can not dirty lockres any more,
// so dlm_thread shuffle list will not run
downconvert lock from EX to NR
upconvert lock from NR to EX
<<< migration may schedule out here, then
<<< node 2 send down convert request to convert type from EX to
<<< NR, then send up convert request to convert type from NR to
<<< EX, at this time, lockres granted list is empty, and two locks
<<< in the converting list, node x up convert lock followed by
<<< node 2 up convert lock.
// will set lockres RES_MIGRATING flag, the following
// lock/unlock can not run
dlm_lockres_release_ast(dlm, res);
}
dlm_send_one_lockres()
dlm_process_recovery_data()
for (i=0; i<mres->num_locks; i++)
if (ml->node == dlm->node_num)
for (j = DLM_GRANTED_LIST; j <= DLM_BLOCKED_LIST; j++) {
list_for_each_entry(lock, tmpq, list)
if (lock) break; <<< lock is invalid as grant list is empty.
}
if (lock->ml.node != ml->node)
BUG() >>> crash here
}
I see the above locks status from a vmcore of our internal bug.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com> Cc: Sunil Mushran <sunil.mushran@gmail.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As sysctl_hung_task_timeout_sec is unsigned long, when this value is
larger then LONG_MAX/HZ, the function schedule_timeout_interruptible in
watchdog will return immediately without sleep and with print :
When I decrease the value of nr_hugepage in procfs a lot, softlockup
happens. It is because there is no chance of context switch during this
process.
On the other hand, when I allocate a large number of hugepages, there is
some chance of context switch. Hence softlockup doesn't happen during
this process. So it's necessary to add the context switch in the
freeing process as same as allocating process to avoid softlockup.
When I freed 12 TB hugapages with kernel-2.6.32-358.el6, the freeing
process occupied a CPU over 150 seconds and following softlockup message
appeared twice or more.
BUG: soft lockup - CPU#16 stuck for 67s! [sh:12883] ...
Pid: 12883, comm: sh Not tainted 2.6.32-358.el6.x86_64 #1
Call Trace:
free_pool_huge_page+0xb8/0xd0
set_max_huge_pages+0x128/0x190
hugetlb_sysctl_handler_common+0x113/0x140
hugetlb_sysctl_handler+0x1e/0x20
proc_sys_call_handler+0x97/0xd0
proc_sys_write+0x14/0x20
vfs_write+0xb8/0x1a0
sys_write+0x51/0x90
__audit_syscall_exit+0x265/0x290
system_call_fastpath+0x16/0x1b
I have not confirmed this problem with upstream kernels because I am not
able to prepare the machine equipped with 12TB memory now. However I
confirmed that the amount of decreasing hugepages was directly
proportional to the amount of required time.
I measured required times on a smaller machine. It showed 130-145
hugepages decreased in a millisecond.
arch/sh/kernel/dumpstack.c: In function 'print_trace_address':
arch/sh/kernel/dumpstack.c:118:2: error: format not a string literal and no format arguments [-Werror=format-security]
Use the "%s" format so that it's impossible to interpret 'data' as a
format string.
Signed-off-by: Matt Fleming <matt.fleming@intel.com> Reported-by: Kees Cook <keescook@chromium.org> Acked-by: Kees Cook <keescook@chromium.org> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.
The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled. If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.
This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.
The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.
Commit 3e6c6f630a5282df8f3393a59f10eb9c56536d23 ("Delay creation of
khcvd thread") moved the call of hvc_init from being a device_initcall
into hvc_alloc, and used a non-null hvc_driver as indication of whether
hvc_init had already been called.
The problem with this is that hvc_driver is only assigned a value
at the bottom of hvc_init, and so there is a window where multiple
hvc_alloc calls can be in progress at the same time and hence try
and call hvc_init multiple times. Previously the use of device_init
guaranteed that hvc_init was only called once.
This manifests itself as sporadic instances of two hvc_init calls
racing each other, and with the loser of the race getting -EBUSY
from tty_register_driver() and hence that virtual console fails:
Couldn't register hvc console driver
virtio-ports vport0p1: error -16 allocating hvc for port
Here we add an atomic_t to guarantee we'll never run hvc_init twice.
Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 3e6c6f630a52 ("Delay creation of khcvd thread") Reported-by: Jim Somerville <Jim.Somerville@windriver.com> Tested-by: Jim Somerville <Jim.Somerville@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
After suspend another Renesas PCI-X USB 3.0 card doesn't work.
[root@fedora-20 ~]# lspci -vmnnd 1912:
Device: 03:00.0
Class: USB controller [0c03]
Vendor: Renesas Technology Corp. [1912]
Device: uPD720202 USB 3.0 Host Controller [0015]
SVendor: Renesas Technology Corp. [1912]
SDevice: uPD720202 USB 3.0 Host Controller [0015]
Rev: 02
ProgIf: 30
This patch should be applied to stable kernel 3.14 that contain
the commit 1aa9578c1a9450fb21501c4f549f5b1edb557e6d
"xhci: Fix resume issues on Renesas chips in Samsung laptops"
The TXMAXP register is not set correctly for full speed bulk case
when the can_bulk_split() is used. Without this PIO transfers will
not take place correctly
The "mult" factor needs to be updated correctly for the
can_bulk_split() case
The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 0 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 0 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
Without the AUTOSET the DMA transfers will not progress in mode1
jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2)
The -ENOENT is due to readdir calling dir_emit on the same entry twice.
If the dir_emit callback sleeps and the tree is changed underneath us,
we won't be able to trust deh_offset(deh) anymore. We need to save
next_pos before we might sleep so we can find the next entry.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.
This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.
The bug was occuring when:
- lport created, tport (our per-lport, per-provider context) is
allocated.
tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
instead of searching for new tpg by calling ft_lport_find_tpg.
tport->tpg is still invalid, and will access freed memory.
see https://bugzilla.redhat.com/show_bug.cgi?id=1071340
Signed-off-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message()
where during ERL=2 connection recovery, a bogus conn_p pointer could
end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION
notifying the initiator that cmd->logout_cid has failed.
The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with
a bogus conn_p pointer in iscsit_build_conn_drop_async_message().
The original code always set the upper 32 bits to zero because it was
doing a shift of the wrong variable.
Fixes: 1a4f550a09f8 ('[SCSI] arcmsr: 1.20.00.15: add SATA RAID plus other fixes') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR(). But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().
As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.
In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.
This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().
Guard against a potential buffer overrun. The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.
Reported-by: Nico Golde <nico@ngolde.de> Reported-by: Fabian Yamaguchi <fabs@goesec.de> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like this bug has been here since these write counts were
introduced, not sure why it was just noticed now.
Thanks also to Jan Kara for pointing out the problem.
Reported-by: Matthew Rahtz <mrahtz@rapitasystems.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early. However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).
The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.
A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field. This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.
This patch should be applied to stable kernels from 3.10 onward.
The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer. We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.
Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit
kernel.
Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.
Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;
The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id. It also should have been "if (avail >= 8)" because when it is 8,
there is space.
Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For vmcore generated by LPAE enabled kernel, user space
utility such as crash needs additional infomation to
parse.
So this patch add arch_crash_save_vmcoreinfo as what PAE enabled
i386 linux does.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Liu Hua <sdu.liu@huawei.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".
Reviewed-by: Dave Martin <Dave.Martin@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Alex Wu <wuquanming@huawei.com> Signed-off-by: Xiangyu Lu <luxiangyu@huawei.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the
proper clock domains for USB Host and USB TLL modules.
Gets rid of the following warnings during boot
omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
Reported-by: Nishanth Menon <nm@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Fixes: de231388cb80a8ef3e779bbfa0564ba0157b7377 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3") Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Partha Basak <parthab@india.ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interrupt has become active on the INTC it will stay active
until it is acked, even if masked or de-asserted. The
INTC_PENDING_IRQn registers are however updated and since these are
used by omap_intc_handle_irq to determine which interrupt to handle,
it will never see the active interrupt. This will result in a storm of
useless interrupts that is only stopped when another higher priority
interrupt is asserted.
Fix by sending the INTC an acknowledge if we find no interrupts to
handle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_task_zombie() first does EXIT_ZOMBIE->EXIT_DEAD transition and
drops tasklist_lock. If this task is not the natural child and it is
traced, we change its state back to EXIT_ZOMBIE for ->real_parent.
The last transition is racy, this is even documented in 50b8d257486a
"ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE
race". wait_consider_task() tries to detect this transition and clear
->notask_error but we can't rely on ptrace_reparented(), debugger can
exit and do ptrace_unlink() before its sub-thread sets EXIT_ZOMBIE.
And there is another problem which were missed before: this transition
can also race with reparent_leader() which doesn't reset >exit_signal if
EXIT_DEAD, assuming that this task must be reaped by someone else. So
the tracee can be re-parented with ->exit_signal != SIGCHLD, and if
/sbin/init doesn't use __WALL it becomes unreapable.
Change reparent_leader() to update ->exit_signal even if EXIT_DEAD.
Note: this is the simple temporary hack for -stable, it doesn't try to
solve all problems, it will be reverted by the next changes.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com> Reported-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Michal Schmidt <mschmidt@redhat.com> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Lennart Poettering <lpoetter@redhat.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable csize in structure jffs2_tmp_dnode_info is of type uint16_t, but it
is used to hold the compressed data length(csize) which is declared as uint32_t.
So, when the value of csize exceeds 16bits, it gets truncated when assigned to
tn->csize. This is causing a kernel BUG.
Changing the definition of csize in jffs2_tmp_dnode_info to uint32_t fixes the issue.
This crash is caused because the 'positions' is declared as an array of signed
short. The value of position is in the range 0..65535, and will be converted
to a negative number when the position is greater than 32767 and causes a
corruption and crash. Changing the definition to 'unsigned short' fixes this
issue
Signed-off-by: Jayachandran C <jchandra@broadcom.com> Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes authentication failure on LE link re-connection when
BlueZ acts as slave (peripheral). LTK is removed from the internal list
after its first use causing PIN or Key missing reply when re-connecting
the link. The LE Long Term Key Request event indicates that the master
is attempting to encrypt or re-encrypt the link.
Pre-condition: BlueZ host paired and running as slave.
How to reproduce(master):
1) Establish an ACL LE encrypted link
2) Disconnect the link
3) Try to re-establish the ACL LE encrypted link (fails)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Reply (0x08|0x001a) plen 18
Handle: 64
Long term key: 2aa531db2fce9f00a0569c7d23d17409
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Reply (0x08|0x001a) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 64
Encryption: Enabled with AES-CCM (0x01)
...
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 3
< HCI Command: LE Set Advertise Enable (0x08|0x000a) plen 1
Advertising: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertise Enable (0x08|0x000a) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Neg Reply (0x08|0x001b) plen 2
Handle: 64
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Neg Reply (0x08|0x001b) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 64
Reason: Authentication Failure (0x05)
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 0
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
When checking a system call return code for an error,
linux_sparc_syscall was sign-extending the lower 32-bit value and
comparing it to -ERESTART_RESTARTBLOCK. lseek can return valid return
codes whose lower 32-bits alone would indicate a failure (such as 4G-1).
Use the whole 64-bit value to check for errors. Only the 32-bit path
should sign extend the lower 32-bit value.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Acked-by: Allen Pais <allen.pais@oracle.com> Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
However, the Kconfig selects HAVE_ARCH_JUMP_LABEL unconditionally
for all SPARC. This in turn leads to the following failure when
doing allmodconfig coverage builds:
kernel/built-in.o: In function `__jump_label_update':
jump_label.c:(.text+0x8560c): undefined reference to `arch_jump_label_transform'
kernel/built-in.o: In function `arch_jump_label_transform_static':
(.text+0x85cf4): undefined reference to `arch_jump_label_transform'
make: *** [vmlinux] Error 1
Change HAVE_ARCH_JUMP_LABEL to be conditional on SPARC64 so that it
matches the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit broke the behavior of __copy_from_user_inatomic when
it is only partially successful. Instead of returning the number
of bytes not copied, it now returns 1. This translates to the
wrong value being returned by iov_iter_copy_from_user_atomic.
xfstests generic/246 and LTP writev01 both fail on btrfs and nfs
because of this.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Cc: Hugh Dickins <hughd@google.com> Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMBA APB Bridges lacks the 'ranges' of-property describing the
PCI I/O and memory areas located beneath the bridge. Faking this
information has been performed by reading range registers in the
APB bridge, and calculating the corresponding areas.
In commit 01f94c4a6ced476ce69b895426fc29bfc48c69bd
("Fix sabre pci controllers with new probing scheme.") a bug was
introduced into this calculation, causing the PCI memory areas
to be calculated incorrectly: The shift size was set to be
identical for I/O and MEM ranges, which is incorrect.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Binding might result in a NULL device which is later dereferenced
without checking.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three buffer overflows addressed in this patch.
1) In isdnloop_fake_err() we add an 'E' to a 60 character string and
then copy it into a 60 character buffer. I have made the destination
buffer 64 characters and I'm changed the sprintf() to a snprintf().
2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60
character buffer so we have 54 characters. The ->eazlist[] is 11
characters long. I have modified the code to return if the source
buffer is too long.
3) In isdnloop_command() the cbuf[] array was 60 characters long but the
max length of the string then can be up to 79 characters. I made the
cbuf array 80 characters long and changed the sprintf() to snprintf().
I also removed the temporary "dial" buffer and changed it to use "p"
directly.
Unfortunately, we pass the "cbuf" string from isdnloop_command() to
isdnloop_writecmd() which truncates anything over 60 characters to make
it fit in card->omsg[]. (It can accept values up to 255 characters so
long as there is a '\n' character every 60 characters). For now I have
just fixed the memory corruption bug and left the other problems in this
driver alone.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EINVAL unless all of user-given strings are correctly
NUL-terminated.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nla_strcmp compares the string length plus one, so it's implicitly
including the nul-termination in the comparison.
int nla_strcmp(const struct nlattr *nla, const char *str)
{
int len = strlen(str) + 1;
...
d = memcmp(nla_data(nla), str, len);
However, if NLA_STRING is used, userspace can send us a string without
the nul-termination. This is a problem since the string
comparison will not match as the last byte may be not the
nul-termination.
Fix this by skipping the comparison of the nul-termination if the
attribute data is nul-terminated. Suggested by Thomas Graf.
Cc: Florian Westphal <fw@strlen.de> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.
As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:
1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
(only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)
Fixes: c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify processing to workqueue") Reported-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes a test in start_new_rx_buffer() that checks whether
a copy operation is less than MAX_BUFFER_OFFSET in length, since
MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of
start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Sander Eikelenboom <linux@eikelenboom.it> Reported-By: Sander Eikelenboom <linux@eikelenboom.it> Tested-By: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mergeable buffers are disabled, and the
incoming packet is too large for the rx buffer,
get_rx_bufs returns success.
This was intentional in order for make recvmsg
truncate the packet and then handle_rx would
detect err != sock_len and drop it.
Unfortunately we pass the original sock_len to
recvmsg - which means we use parts of iov not fully
validated.
Fix this up by detecting this overrun and doing packet drop
immediately.
CVE-2014-0077
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as
transport),the ipsec header need to be added in the first fragment, so the mtu
will decrease to reserve space for it, then the second fragment come, the mtu
should be turn back, as the commit 0c1833797a5a6ec23ea9261d979aa18078720b74
said. however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use
*mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway
equal with the first fragment's. and cannot turn back.
when I test through ping6 -c1 -s5000 $ip (mtu=1280):
...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232
...frag (1232|1216)
...frag (2448|1216)
...frag (3664|1216)
...frag (4880|164)
which should be:
...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232
...frag (1232|1232)
...frag (2464|1232)
...frag (3696|1232)
...frag (4928|116)
so delete the min() when change back the mtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Fixes: 75a493e60ac4bb ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size") Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.
Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When copying in a struct msghdr from the user, if the user has set the
msg_namelen parameter to a negative value it gets clamped to a valid
size due to a comparison between signed and unsigned values.
Ensure the syscall errors when the user passes in a negative value.
Signed-off-by: Matthew Leach <matthew.leach@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With TX VLAN offload enabled the source MAC address for frames sent using the
VLAN interface is currently set to the address of the real interface. This is
wrong since the VLAN interface may be configured with a different address.
This patch sets the source address before calling the create function of the
real interface.
Signed-off-by: Peter Boström <peter.bostrom@netrounds.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DST_NOCOUNT should only be used if an authorized user adds routes
locally. In case of routes which are added on behalf of router
advertisments this flag must not get used as it allows an unlimited
number of routes getting added remotely.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02b00704 ("net: fix multithreaded signal handling in
unix recv routines").
To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.
Fixes: b3ca9b02b00704 ("net: fix multithreaded signal handling in unix recv routines") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MLD queries are supposed to have an IPv6 link-local source address
according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch
adds a sanity check to ignore such broken MLD queries.
Without this check, such malformed MLD queries can result in a
denial of service: The queries are ignored by any MLD listener
therefore they will not respond with an MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While working on ec0223ec48a9 ("net: sctp: fix sctp_sf_do_5_1D_ce to
verify if we/peer is AUTH capable"), we noticed that there's a skb
memory leakage in the error path.
Running the same reproducer as in ec0223ec48a9 and by unconditionally
jumping to the error label (to simulate an error condition) in
sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about
the unfreed chunk->auth_chunk skb clone:
What happens is that commit bbd0d59809f9 clones the skb containing
the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case
that an endpoint requires COOKIE-ECHO chunks to be authenticated:
When we enter sctp_sf_do_5_1D_ce() and before we actually get to
the point where we process (and subsequently free) a non-NULL
chunk->auth_chunk, we could hit the "goto nomem_init" path from
an error condition and thus leave the cloned skb around w/o
freeing it.
The fix is to centrally free such clones in sctp_chunk_destroy()
handler that is invoked from sctp_chunk_free() after all refs have
dropped; and also move both kfree_skb(chunk->auth_chunk) there,
so that chunk->auth_chunk is either NULL (since sctp_chunkify()
allocs new chunks through kmem_cache_zalloc()) or non-NULL with
a valid skb pointer. chunk->skb and chunk->auth_chunk are the
only skbs in the sctp_chunk structure that need to be handeled.
While at it, we should use consume_skb() for both. It is the same
as dev_kfree_skb() but more appropriately named as we are not
a device but a protocol. Also, this effectively replaces the
kfree_skb() from both invocations into consume_skb(). Functions
are the same only that kfree_skb() assumes that the frame was
being dropped after a failure (e.g. for tools like drop monitor),
usage of consume_skb() seems more appropriate in function
sctp_chunk_destroy() though.
Fixes: bbd0d59809f9 ("[SCTP]: Implement the receive and verification of AUTH chunk") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <yasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:
* If there was a frequency transition before, the multiplier read from the
register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
register always reads as zero, regardless of the current multiplier that
is set using switches on the mainboard and that the CPU is running at.
The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.
For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.
There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.
During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.
This patch flushes the cache during frequency transition. It fixes the
instability.
Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
open during other activity (running other kernel code with the port open
shouldn't cause any misbehavior, but we should better be safe and keep
the port closed)
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function kthread_run() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
free_buff_list and rec_buff_list are initialized in the middle of hdpvr_probe(),
but if something bad happens before that, error handling code calls hdpvr_delete(),
which contains iteration over the lists (via hdpvr_free_buffers()).
The patch moves the lists initialization to the beginning and by the way fixes
goto label in error handling of registering videodev.
Found by Linux Driver Verification project (linuxtesting.org).
In dvb_ringbuffer lock-less synchronizationof reader and writer threads is done
with separateread and write pointers. Sincedvb_ringbuffer_flush() modifies the
read pointer, this function must not be called from the writer thread.
This patch removes the dvb_ringbuffer_flush() calls in the dmxdev ringbuffer
write functions, this fixes Oopses "Unable to handle kernel paging request"
I could observe for the call chaindvb_demux_read ->dvb_dmxdev_buffer_read ->
dvb_ringbuffer_read_user -> __copy_to_user (the reader side of the ringbuffer).
The flush calls at the write side are not necessary anyway since ringbuffer_flush
is also called in dvb_dmxdev_buffer_read() when an error condition is set in the
ringbuffer.
This patch should also be applied to stable kernels.
Walking rbtree while it's modified is a Bad Idea(tm); besides,
the result of find_vma() can be freed just as it's getting returned
to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit
earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET -
in that case we don't even look at its result).
While we are at it, what prevents VIDIOC_PREPARE_BUF calling
v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() ->
__buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(),
AFAICS without having taken ->mmap_sem anywhere in process? The code flow
is bloody convoluted and depends on a bunch of things done by initialization,
so I certainly might've missed something...
When subdev registration fails the subdev v4l2_dev field is left to a
non-NULL value. Later calls to v4l2_device_unregister_subdev() will
consider the subdev as registered and will module_put() the subdev
module without any matching module_get().
Fix this by setting the subdev v4l2_dev field to NULL in
v4l2_device_register_subdev() when the function fails.
Commit 091f0ea30074bc43f9250961b3247af713024bc6 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.
Reported-by: Roland Dreier <roland@purestorage.com> Tested-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: use GET_ASIC_REV() instead of tg3_asic_rev()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[hq: Backproted to 3.4: Adjust context] Signed-off-by: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the 5718, 5719 and 5720 serdes devices, powering down function 0
results in all the other ports being powered down. Add code to skip
function 0 power down.
v2:
- Modify tg3_phy_power_bug() function to use a switch instead of a
complicated if statement. Suggested by Joe Perches.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
s/tg3_asic_rev\(tp\)/GET_ASIC_REV(tp->pci_chip_rev_id)/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[hq: Backported to 3.4: Adjust context] Signed-off-by: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sandy bridge EDAC is calculating the memory size with overflow.
Basically, the size field and the integer calculation is using 32 bits.
More bits are needed, when the DIMM memories have high density.
The net result is that memories are improperly reported there, when
high-density DIMMs are used:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 0, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 1, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
As the number of pages value is handled at the EDAC core as unsigned
ints, the driver shows the 16 GB memories at sysfs interface as 16760832
MB! The fix is simple: calculate the number of pages as unsigned 64-bits
integer.
After the patch, the memory size (16 GB) is properly detected:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 0, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 1, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2:
- Adjust context
- Debug log function is debugf0(), not edac_dbg()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Release the lock before mmc_signal_sdio_irq is called by
mxs_mmc_enable_sdio_irq.
Backtrace:
[ 65.470000] =============================================
[ 65.470000] [ INFO: possible recursive locking detected ]
[ 65.470000] 3.5.0-rc5 #2 Not tainted
[ 65.470000] ---------------------------------------------
[ 65.470000] ksdioirqd/mmc0/73 is trying to acquire lock:
[ 65.470000] (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]
[ 65.470000]
[ 65.470000] but task is already holding lock:
[ 65.470000] (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]
[ 65.470000]
[ 65.470000] other info that might help us debug this:
[ 65.470000] Possible unsafe locking scenario:
[ 65.470000]
[ 65.470000] CPU0
[ 65.470000] ----
[ 65.470000] lock(&(&host->lock)->rlock#2);
[ 65.470000] lock(&(&host->lock)->rlock#2);
[ 65.470000]
[ 65.470000] *** DEADLOCK ***
[ 65.470000]
[ 65.470000] May be due to missing lock nesting notation
[ 65.470000]
[ 65.470000] 1 lock held by ksdioirqd/mmc0/73:
[ 65.470000] #0: (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]
[ 65.470000]
[ 65.470000] stack backtrace:
[ 65.470000] [<c0014990>] (unwind_backtrace+0x0/0xf4) from [<c005ccb8>] (__lock_acquire+0x14f8/0x1b98)
[ 65.470000] [<c005ccb8>] (__lock_acquire+0x14f8/0x1b98) from [<c005d3f8>] (lock_acquire+0xa0/0x108)
[ 65.470000] [<c005d3f8>] (lock_acquire+0xa0/0x108) from [<c02f671c>] (_raw_spin_lock_irqsave+0x48/0x5c)
[ 65.470000] [<c02f671c>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc])
[ 65.470000] [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) from [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc])
[ 65.470000] [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) from [<c0219b38>] (sdio_irq_thread+0x1bc/0x274)
[ 65.470000] [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) from [<c003c324>] (kthread+0x8c/0x98)
[ 65.470000] [<c003c324>] (kthread+0x8c/0x98) from [<c00101ac>] (kernel_thread_exit+0x0/0x8)
[ 65.470000] BUG: spinlock lockup suspected on CPU#0, ksdioirqd/mmc0/73
[ 65.470000] lock: 0xc3358724, .magic: dead4ead, .owner: ksdioirqd/mmc0/73, .owner_cpu: 0
[ 65.470000] [<c0014990>] (unwind_backtrace+0x0/0xf4) from [<c01b46b0>] (do_raw_spin_lock+0x100/0x144)
[ 65.470000] [<c01b46b0>] (do_raw_spin_lock+0x100/0x144) from [<c02f6724>] (_raw_spin_lock_irqsave+0x50/0x5c)
[ 65.470000] [<c02f6724>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc])
[ 65.470000] [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) from [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc])
[ 65.470000] [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) from [<c0219b38>] (sdio_irq_thread+0x1bc/0x274)
[ 65.470000] [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) from [<c003c324>] (kthread+0x8c/0x98)
[ 65.470000] [<c003c324>] (kthread+0x8c/0x98) from [<c00101ac>] (kernel_thread_exit+0x0/0x8)
Reported-by: Attila Kinali <attila@kinali.ch> Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
[bwh: Backported to 3.2:
- Adjust context
- HW_SSP_STATUS is a simple rather than function-like macro] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omapfb does not currently set pseudo palette correctly for color depths
above 16bpp, making red text invisible, command like
echo -e '\e[0;31mRED' > /dev/tty1
will display nothing on framebuffer console in 24bpp mode.
This is because temporary variable is declared incorrectly, fix it.
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall. Check for invalid
values and set a register bit to flush the TX channels. The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "rpm * div" operations can overflow here, so this patch adds an
upper limit to rpm to prevent that. Jean Delvare helped me with this
patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Roger Lucas <vt8231@hiddenengine.co.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The crash reported and investigated in commit 5f4513 turned out to be
caused by a change to the read interface on newer (2012) SMCs.
Tests by Chris show that simply reading the data valid line is enough
for the problem to go away. Additional tests show that the newer SMCs
no longer wait for the number of requested bytes, but start sending
data right away. Apparently the number of bytes to read is no longer
specified as before, but instead found out by reading until end of
data. Failure to read until end of data confuses the state machine,
which eventually causes the crash.
As a remedy, assuming bit0 is the read valid line, make sure there is
nothing more to read before leaving the read function.
Tested to resolve the original problem, and runtested on MBA3,1,
MBP4,1, MBP8,2, MBP10,1, MBP10,2. The patch seems to have no effect on
machines before 2012.
Tested-by: Chris Murphy <chris@cmurf.com> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Qiang Huang <h.huangqiang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer Reported-by: Ashecrow Reported-by: Frank Zafka <kafkaesque1978@gmail.com> Reported-by: Peter Frühberger <fritsch@xbmc.org> Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Weng Meiling <wengmeiling.weng@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log