MPP_F6281_MASK would be previously be returned when on mv88f6282,
which would disallow some valid MPP configurations.
Commit 830f8b91 (arm: plat-orion: fix printing of "MPP config
unavailable on this hardware") made this problem visible as an invalid
MPP configuration is now correctly detected and not applied.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-enable chipidea irq even if there's no role changing to do. This is
a problem since b183c19f ("USB: chipidea: re-order irq handling to avoid
unhandled irqs"); when it manifests, chipidea irq gets disabled for good.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.
This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally, the kernel emulates a few instructions that are unimplemented
on some processors (e.g. the old dcba instruction), or privileged (e.g.
mfpvr). The emulation of unimplemented instructions is currently not
working on the PowerNV platform. The reason is that on these machines,
unimplemented and illegal instructions cause a hypervisor emulation
assist interrupt, rather than a program interrupt as on older CPUs.
Our vector for the emulation assist interrupt just calls
program_check_exception() directly, without setting the bit in SRR1
that indicates an illegal instruction interrupt. This fixes it by
making the emulation assist interrupt set that bit before calling
program_check_interrupt(). With this, old programs that use no-longer
implemented instructions such as dcba now work again.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.
__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.
This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.
The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().
Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.
This patch reworks the UEFI anti-bricking code, including an effective
reversion of cc5a080c and 31ff2f20. It turns out that calling
QueryVariableInfo() from boot services results in some firmware
implementations jumping to physical addresses even after entering virtual
mode, so until we have 1:1 mappings for UEFI runtime space this isn't
going to work so well.
Reverting these gets us back to the situation where we'd refuse to create
variables on some systems because they classify deleted variables as "used"
until the firmware triggers a garbage collection run, which they won't do
until they reach a lower threshold. This results in it being impossible to
install a bootloader, which is unhelpful.
Feedback from Samsung indicates that the firmware doesn't need more than
5KB of storage space for its own purposes, so that seems like a reasonable
threshold. However, there's still no guarantee that a platform will attempt
garbage collection merely because it drops below this threshold. It seems
that this is often only triggered if an attempt to write generates a
genuine EFI_OUT_OF_RESOURCES error. We can force that by attempting to
create a variable larger than the remaining space. This should fail, but if
it somehow succeeds we can then immediately delete it.
I've tested this on the UEFI machines I have available, but I don't have
a Samsung and so can't verify that it avoids the bricking problem.
The auth code is called from a variety of contexts, include the mon_client
(protected by the monc's mutex) and the messenger callbacks (currently
protected by nothing). Avoid chaos by protecting all auth state with a
mutex. Nothing is blocking, so this should be simple and lightweight.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use wrapper functions that check whether the auth op exists so that callers
do not need a bunch of conditional checks. Simplifies the external
interface.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the messenger calls out to a get_authorizer con op, which will
create a new authorizer if it doesn't yet have one. In the meantime, when
we rotate our service keys, the authorizer doesn't get updated. Eventually
it will be rejected by the server on a new connection attempt and get
invalidated, and we will then rebuild a new authorizer, but this is not
ideal.
Instead, if we do have an authorizer, call a new update_authorizer op that
will verify that the current authorizer is using the latest secret. If it
is not, we will build a new one that does. This avoids the transient
failure.
This fixes one of the sorry sequence of events for bug
http://tracker.ceph.com/issues/4282
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were invalidating the authorizer by removing the ticket handler
entirely. This was effective in inducing us to request a new authorizer,
but in the meantime it mean that any authorizer we generated would get a
new and initialized handler with secret_id=0, which would always be
rejected by the server side with a confusing error message:
auth: could not find secret_id=0
cephx: verify_authorizer could not get service secret for service osd secret_id=0
Instead, simply clear the validity field. This will still induce the auth
code to request a new secret, but will let us continue to use the old
ticket in the meantime. The messenger code will probably continue to fail,
but the exponential backoff will kick in, and eventually the we will get a
new (hopefully more valid) ticket from the mon and be able to continue.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We maintain a counter of failed auth attempts to allow us to retry once
before failing. However, if the second attempt succeeds, the flag isn't
cleared, which makes us think auth failed again later when the connection
resets for other reasons (like a socket error).
This is one part of the sorry sequence of events in bug
http://tracker.ceph.com/issues/4282
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for last entry is not what we want, we should have
[mem 0x00200000-0x3fffffff] page 2M
[mem 0x40000000-0x7bffffff] page 1G
Actually we merge the continuous ranges with same page size too early.
in this case, before merging we have
[mem 0x00200000-0x3fffffff] page 2M
[mem 0x40000000-0x7bffffff] page 2M
after merging them, will get
[mem 0x00200000-0x7bffffff] page 2M
even we can use 1G page to map
[mem 0x40000000-0x7bffffff]
that will cause problem, because we already map
[mem 0x7fe00000-0x7fffffff] page 1G
[mem 0x7c000000-0x7fdfffff] page 1G
with 1G page, aka [0x40000000-0x7fffffff] is mapped with 1G page already.
During phys_pud_init() for [0x40000000-0x7bffffff], it will not
reuse existing that pud page, and allocate new one then try to use
2M page to map it instead, as page_size_mask does not include
PG_LEVEL_1G. At end will have [7c000000-0x7fffffff] not mapped, loop
in phys_pmd_init stop mapping at 0x7bffffff.
That is right behavoir, it maps exact range with exact page size that
we ask, and we should explicitly call it to map [7c000000-0x7fffffff]
before or after mapping 0x40000000-0x7bffffff.
Anyway we need to make sure ranges' page_size_mask correct and consistent
after split_mem_range for each range.
Fix that by calling adjust_range_size_mask before merging range
with same page size.
-v2: update change log.
-v3: add more explanation why [7c000000-0x7fffffff] is not mapped, and
it causes panic.
Bisected-by: "Xie, ChanglongX" <changlongx.xie@intel.com> Bisected-by: Yuanhan Liu <yuanhan.liu@linux.intel.com> Reported-and-tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/1370015587-20835-1-git-send-email-yinghai@kernel.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes. As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.
This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage. This patch introduces
migration_entry_wait_huge() to solve this.
The watermark check consists of two sub-checks. The first one is:
if (free_pages <= min + lowmem_reserve)
return false;
The check assures that there is minimal amount of RAM in the zone. If
CMA is used then the free_pages is reduced by the number of free pages
in CMA prior to the over-mentioned check.
if (!(alloc_flags & ALLOC_CMA))
free_pages -= zone_page_state(z, NR_FREE_CMA_PAGES);
This prevents the zone from being drained from pages available for
non-movable allocations.
The second check prevents the zone from getting too fragmented.
for (o = 0; o < order; o++) {
free_pages -= z->free_area[o].nr_free << o;
min >>= 1;
if (free_pages <= min)
return false;
}
The field z->free_area[o].nr_free is equal to the number of free pages
including free CMA pages. Therefore the CMA pages are subtracted twice.
This may cause a false positive fail of __zone_watermark_ok() if the CMA
area gets strongly fragmented. In such a case there are many 0-order
free pages located in CMA. Those pages are subtracted twice therefore
they will quickly drain free_pages during the check against
fragmentation. The test fails even though there are many free non-cma
pages in the zone.
This patch fixes this issue by subtracting CMA pages only for a purpose of
(free_pages <= min + lowmem_reserve) check.
Laura said:
We were observing allocation failures of higher order pages (order 5 =
128K typically) under tight memory conditions resulting in driver
failure. The output from the page allocation failure showed plenty of
free pages of the appropriate order/type/zone and mostly CMA pages in
the lower orders.
For full disclosure, we still observed some page allocation failures
even after applying the patch but the number was drastically reduced and
those failures were attributed to fragmentation/other system issues.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Laura Abbott <lauraa@codeaurora.org> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Mel Gorman <mel@csn.ul.ie> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits 050b66152f87c7 (raid10) and 6b740b8d79252f13 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.
This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map(). This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.
This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: Rafael Aquini <aquini@redhat.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Shaohua Li <shli@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC
Egbert Eich fixed a long-standing bug where we simply used a
non-working i2c controller to read the EDID for SDVO-LVDS panels.
Unfortunately some machines seem to not be able to cope with the mode
provided in the EDID. Specifically they seem to not be able to cope
with a 4x pixel mutliplier instead of a 2x one, which seems to have
been worked around by slightly changing the panels native mode in the
VBT so that the dotclock is just barely above 50MHz.
Since it took forever to notice the breakage it's fairly safe to
assume that at least for SDVO-LVDS panels the VBT contains fairly sane
data. So just switch around the order and use VBT modes first.
v2: Also add EDID modes just in case, and spell Egbert correctly.
v3: Elaborate a bit more about what's going on on Chris' machine.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65524 Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Egbert Eich <eich@suse.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com> Reported-by: Michael Scott <hashcode0f@gmail.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct memcg_cache_params has a union. Different parts of this union
are used for root and non-root caches. A part with destroying work is
used only for non-root caches.
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below. It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive,
the mutex isn't.
Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
[...]
acu D 0000000000000001 0 3246 3191 0x00000080
Call Trace:
schedule+0x29/0x70
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x17b/0x220
mutex_lock+0x2b/0x50
cciss_unlocked_open+0x2f/0x110 [cciss]
__blkdev_get+0xd3/0x470
blkdev_get+0x5c/0x1e0
register_disk+0x182/0x1a0
add_disk+0x17c/0x310
cciss_add_disk+0x13a/0x170 [cciss]
cciss_update_drive_info+0x39b/0x480 [cciss]
rebuild_lun_table+0x258/0x370 [cciss]
cciss_ioctl+0x34f/0x470 [cciss]
do_ioctl+0x49/0x70 [cciss]
__blkdev_driver_ioctl+0x28/0x30
blkdev_ioctl+0x200/0x7b0
block_ioctl+0x3c/0x40
do_vfs_ioctl+0x89/0x350
SyS_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
This mutex usage was added into the ioctl path when the big kernel lock
was removed. As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit f96972f2dc63 ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russ Anderson <rja@sgi.com> Cc: Robin Holt <holt@sgi.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Robin Holt <holt@sgi.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russ Anderson <rja@sgi.com> Cc: Robin Holt <holt@sgi.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com> Reported-by: Kevin Hilman <khilman@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whether rbd_client_create() successfully creates a new client or
not, it takes responsibility for getting the ceph_opts structure
it's passed destroyed. If successful, the structure becomes
associated with the created client; if not, rbd_client_create()
will destroy it.
Previously, rbd_get_client() would call ceph_destroy_options()
if rbd_get_client() failed, and that meant it got called twice.
That led freeing various pointers more than once, which is never a
good idea.
This resolves:
http://tracker.ceph.com/issues/4559
Reported-by: Dan van der Ster <dan@vanderster.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Josh Durgin <josh.durgin@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ceph's encode_caps_cb() worked hard to not call __page_cache_alloc()
while holding a lock, but it's spoiled because ceph_pagelist_addpage()
always calls kmap(), which might sleep. Here's the result:
In his review, Alex Elder mentioned that he hadn't checked that
num_fcntl_locks and num_flock_locks were properly decoded on the
server side, from a le32 over-the-wire type to a cpu type.
I checked, and AFAICS it is done; those interested can consult
Locker::_do_cap_update()
in src/mds/Locker.cc and src/include/encoding.h in the Ceph server
code (git://github.com/ceph/ceph).
I also checked the server side for flock_len decoding, and I believe
that also happens correctly, by virtue of having been declared
__le32 in struct ceph_mds_cap_reconnect, in src/include/ceph_fs.h.
Signed-off-by: Jim Schutt <jaschut@sandia.gov> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more. Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.
Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.
That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091 Bisected-and-tested-by: Dmitry S. Demin <dmitryy.demin@gmail.com> Reported-and-tested-by: Jason Cassell <bluesloth600@gmail.com> Tracked-down-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Sun, 9 Jun 2013 20:09:24 +0000 (21:09 +0100)]
s390: Add pgste to ptep_modify_prot_start()
Commit 52f36be0f4e2 's390/pgtable: Fix check for pgste/storage key
handling', which was commit b56433cb782d upstream, added a use of
pgste to ptep_modify_prot_start(), but this variable does not exist.
In mainline, pgste was added by commit d3383632d4e8 's390/mm: add pte
invalidation notifier for kvm' and initialised to the return value of
pgste_get_lock(ptep). Initialise it similarly here.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31ade30692dc9680bfc95700d794818fa3f754ac, timekeeping_init()
checks for presence of persistent clock by attempting to read a non-zero
time value. This is an issue on platforms where persistent_clock (instead
is implemented as a free-running counter (instead of an RTC) starting
from zero on each boot and running during suspend. Examples are some ARM
platforms (e.g. PandaBoard).
An attempt to read such a clock during timekeeping_init() may return zero
value and falsely declare persistent clock as missing. Additionally, in
the above case suspend times may be accounted twice (once from
timekeeping_resume() and once from rtc_resume()), resulting in a gradual
drift of system time.
This patch does a run-time correction of the issue by doing the same check
during timekeeping_suspend().
A better long-term solution would have to return error when trying to read
non-existing clock and zero when trying to read an uninitialized clock, but
that would require changing all persistent_clock implementations.
This patch addresses the immediate breakage, for now.
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Feng Tang <feng.tang@intel.com>
[jstultz: Tweaked commit message and subject] Signed-off-by: John Stultz <john.stultz@linaro.org>
[zoran.markovic@linaro.org: reworked patch to fit 3.9-stable.] Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xen_play_dead is an undead function. When the vCPU is told to
offline it ends up calling xen_play_dead wherin it calls the
VCPUOP_down hypercall which offlines the vCPU. However, when the
vCPU is onlined back, it resumes execution right after
VCPUOP_down hypercall.
That was OK (albeit the API for play_dead assumes that the CPU
stays dead and never returns) but with commit 4b0c0f294
(tick: Cleanup NOHZ per cpu data on cpu down) that is no longer safe
as said commit resets the ts->inidle which at the start of the
cpu_idle loop was set.
b/c ts_inidle is set to zero. Thomas suggested that we just add a workaround
to call tick_nohz_idle_enter before returning from xen_play_dead() - and
that is what this patch does and fixes the issue.
We also add the stable part b/c git commit 4b0c0f294 is on the stable
tree.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671ad3 ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Pekka Riikonen <priikone@iki.fi> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Currently the driver's assumed behavior for a modeset with an attached
FB is that the corresponding connector will be switched to DPMS ON mode
if it happened to be in DPMS OFF (or another power save mode). This
wasn't enforced though if only the FB changed, everything else (format,
connector etc.) remaining the same. In this case we only set the new FB
base and left the connector in the old power save mode.
Fix this by forcing a full modeset whenever there is an attached FB and
any affected connector is in a power save mode.
V_2: Run the test for encoders in power save mode outside the the
test for fb change: user space may have just disabled the encoders
but left everything else in place. Make sure the connector list is
not empty before running this test.
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On pseries machines the detection for max_bus_speed should be done
through an OpenFirmware property. This patch adds a function to perform
this detection and a hook to perform dynamic adding of the function only
for pseries. This is done by overwriting the weak
pcibios_root_bridge_prepare function which is called by
pci_create_root_bus().
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit e61133dda480062d221f09e4fc18f66763f8ecd0 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.
[Small change to factor out the hack into a separate function -- BenH]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch implements a new PAPR change which allows
the OS to force the use of 32 bit MSIs, regardless of what
the PCI capabilities indicate. This is required for some
devices that advertise support for 64 bit MSIs but don't
actually support them.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a PCI quirk for VGA devices on Power to set the default VGA device.
Ensures a default VGA is always set if a graphics adapter is present,
even if firmware did not initialize it. If more than one graphics
adapter is present, ensure the one initialized by firmware is set
as the default VGA device. This ensures that X autoconfiguration
will work.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9f29ab11ddbf ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
X can again get -EIO when it does not expect it. And even worse score
a SIGBUS when accessing gtt mmaps. The established ABI is that we
_only_ return an -EIO from execbuf - all other ioctls should just
work. And since the reset code moves all bos out of gpu domains and
clears out all the last_seqno/ring tracking there really shouldn't be
any reason for non-execbuf code to ever touch the hw and see an -EIO.
After some extensive discussions we've noticed that these spurios -EIO
are caused by i915_gem_wait_for_error:
That is easy to fix by returning 0 instead of -EIO, since grabbing the
dev->struct_mutex does not yet mean that we actually want to touch the
hw. And so there is no reason at all to fail with -EIO.
But that's not the entire since, since often (at least it's easily
googleable) dmesg indicates that the reset fails and we declare the
gpu wedged. Then, quite a bit later X wakes up with the "Timed out
waiting for the gpu reset to complete" DRM_ERROR message in
wait_for_errror and brings down the desktop with an -EIO/SIGBUS.
So clearly we're missing a wakeup somewhere, since the gpu reset just
doesn't take 10 seconds to complete. And indeed we're do handle the
terminally wedged state wrong.
Fix this all up.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
Signed-off-by: Egbert Eich <eich@suse.de> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When GPU acceleration is disabled, drm_vblank_cleanup() will free the
vblank-related data, such as vblank_refcount, vblank_inmodeset, etc.
But we found that drm_vblank_post_modeset() may be called after the
cleanup, which use vblank_refcount and vblank_inmodeset. And this will
cause a kernel panic.
Fix this by return immediately if dev->num_crtcs is zero. This is the
same thing that drm_vblank_pre_modeset() does.
This is a bug fix for some versions of g200se cards while doing
mode-setting.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected
as LM84. Strengthen detection sufficiently enough to avoid this misdetection.
Also improve detection for ADM1021.
Modeled after chip detection code in sensors-detect command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When msync is called on a memory mapped file, that
data is not flushed to the disk.
In Linux, msync calls fsync for the file. For ecryptfs,
fsync just calls the lower level file system's fsync.
Changed the ecryptfs fsync code to call filemap_write_and_wait
before calling the lower level fsync.
Addresses the problem described in http://crbug.com/239536
commit 839db3d10a (cifs: fix up handling of prefixpath= option) changed
the code such that the vol->prepath no longer contained a leading
delimiter and then fixed up the places that accessed that field to
account for that change.
One spot in build_unc_path_to_root was missed however. When doing the
pointer addition on pos, that patch failed to account for the fact that
we had already incremented "pos" by one when adding the length of the
prepath. This caused a buffer overrun by one byte.
This patch fixes the problem by correcting the handling of "pos".
Reported-by: Marcus Moeller <marcus.moeller@gmx.ch> Reported-by: Ken Fallon <ken.fallon@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
The pm runtime reference counting of the driver is broken for the case
when there is more than one transfer queued, leading to the device being
runtime suspend while active. Fix it.
In commit bc09c21 "Fix finding overflowed PMC in interrupt" we added
a printk() to the PMU exception handler. Unfortunately that is not safe.
The problem is that the PMU exception may run even when interrupts are
soft disabled, aka NMI context. We do this so that we can profile parts
of the kernel that have interrupts soft-disabled.
But by calling printk() from the exception handler, we can potentially
deadlock in the printk code on logbuf_lock, eg:
When introducing support for DABRX in 4474ef0, we broke older 32-bit CPUs
that don't have that register.
Some CPUs have a DABR but not DABRX. Configuration are:
- No 32bit CPUs have DABRX but some have DABR.
- POWER4+ and below have the DABR but no DABRX.
- 970 and POWER5 and above have DABR and DABRX.
- POWER8 has DAWR, hence no DABRX.
This introduces CPU_FTR_DABRX and sets it on appropriate CPUs. We use
the top 64 bits for CPU FTR bits since only 64 bit CPUs have this.
Processors that don't have the DABRX will still work as they will fall
back to software filtering these breakpoints via perf_exclude_event().
Signed-off-by: Michael Neuling <mikey@neuling.org> Reported-by: "Gorelik, Jacob (335F)" <jacob.gorelik@jpl.nasa.gov> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").
The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.
Reported-by: Robert Knight <knight@princeton.edu> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Tested-by: Robert Knight <knight@princeton.edu> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__my_cpu_offset is non-volatile, since we want its value to be cached
when we access several per-cpu variables in a row with preemption
disabled. This means that we rely on preempt_{en,dis}able to hazard
with the operation via the barrier() macro, so that we can't end up
migrating CPUs without reloading the per-cpu offset.
Unfortunately, GCC doesn't treat a "memory" clobber on a non-volatile
asm block as a side-effect, and will happily re-order it before other
memory clobbers (including those in prempt_disable()) and cache the
value. This has been observed to break the cmpxchg logic in the slub
allocator, leading to livelock in kmem_cache_alloc in mainline kernels.
This patch adds a dummy memory input operand to __my_cpu_offset,
forcing it to be ordered with respect to the barrier() macro.
Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In August 2012, Matthew Gretton-Dann checked a change into binutils
labelled "Error on obsolete & warn on deprecated registers", apparently as
part of ARMv8 support. Apparently, this was supposed to emit the message
"Warning: This coprocessor register access is deprecated in ARMv8" when
using certain mcr/mrc instructions and building for ARMv8. Unfortunately,
the message that is actually emitted appears to be '(null)', which is
less helpful in comparison.
Even more unfortunately, this is biting us on every single kernel
build with a new gas, because arch/arm/boot/compressed/head.S and some
other files in that directory are built with -march=all since kernel
commit 80cec14a8 "[ARM] Add -march=all to assembly file build in
arch/arm/boot/compressed" back in v2.6.28.
This patch reverts Russell's nice solution and instead marks the head.S
file to be built for armv7-a, which fortunately lets us build all
instructions in that file without warnings even on the broken binutils.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Nicolas Pitre <nico@linaro.org> Cc: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating the DT based boards-ts219.c the none DT ts219-setup.c
was used as a template. This includes a lateinit() call to initialize
the PCIe bus. The code makes use of machine_is_ts219() which is never
true on DT, so a FIXME was added and the code left as is. This was
unproblematic until b73690c8f8b5d: "ARM: Kirkwood: Support basic
hotplug for PCI-E" which changes the way the PCIe bus is
initialized. The non-DT ts219-setup.c now crashes during boot. The
lateinit() call in the DT boards-ts219.c is being called,
machine_is_ts219() is true and so the PCIe is initialized a second
time.
This patch removes the useless, and now clearly dangerous, code from
boards-ts219.c, making ts219-setup.c work again.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VT1802 codec seems to reset EAPD of other pins in the hardware level,
and this was another reason of the silent headphone output on some
machines. As a workaround, introduce a new flag indicating to keep
the EPAD on to the generic parser, and set it in patch_via.c.
Some codec drivers (VIA codecs and some Realtek fixups) set the
automute and automic hooks after calling
snd_hda_gen_parse_auto_config(). In the current code, the hook
pointers are referred only in snd_hda_gen_parse_auto_config() and
passed to snd_hda_jack_detect_enable_callback(), thus changing the
hook values won't change the actually called callbacks properly.
This patch fixes this bug by setting the static functions as the
primary callback functions for the jack detection, and let them
calling the appropriate hooks dynamically.
VIA driver has a special suspend handling only for VT1802 to reduce
the pop noise. During the transition to the generic parser, the
behavior of snd_hda_set_pin_ctl() was also changed to modify the
cached values, too. And this caused a regression where the pin is
still cleared even after the resume (including the resume from power
save), resulting in the silent output.
The fix is simply to replace snd_hda_set_pin_ctl() with the explicit
call of snd_hda_codec_write() again.
Since the transition to the generic parser, the actual routes used
there don't match always with the assumed static paths in some
set_widgets_power_state callbacks. This results in the wrong power
setup in the end. As a temporary workaround, we need to disable the
calls together with the non-functional dynamic power control enum.
Check code and find this error is caused by misusing variable bluetooth_rfkill
where gps_rfkill should be.
Reported-and-tested-by: Iru Cai <mytbk920423@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=58401 Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201 Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com> Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091 Reported-by: Jason Cassell <bluesloth600@gmail.com> Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661 Signed-off-by: Ash Willis <ashwillis@programmer.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501 Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log