The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e219 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
41f8bba7f555 ("of/pci: Add pci_register_io_range() and
pci_pio_to_address()") added support for systems with several I/O ranges
described by OF bindings. It modified pci_address_to_pio() look up the
io_range for a given CPU physical address, but the conversion was wrong.
The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously. Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed. In cases
where we need that state change to be enabled, we must still wait for
completion. For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection. If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.
Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion. The following
functions are returned to their previous behavior:
The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on. pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected. And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.
The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3df9 added new checking that
tripped over this mismatch.
Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.
Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the
ignore_hotplug setting of the device to its parent bridge in case hotplug
notifications related to the graphics adapter switching are given for the
bridge rather than for the device itself (they need to be ignored in both
cases).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927 Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Reported-and-tested-by: tiagdtd-lava <tiagdtd-lava@yahoo.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bd31b85960a7 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.
This fixes:
drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
spin_lock_irqsave(&nw_gpio_lock, flags);
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
^
drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
spin_unlock_irqrestore(&nw_gpio_lock, flags);
^
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com> Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.
Log:
PM: noirq freeze of devices complete after 1.425 msecs
Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)
WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access
CPU1: shutdown
^ or here
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Fixes: 73e1ab41a80d (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LCDIF engines embedded in i.MX6sl and i.MX6sx SoCs need the axi clock
as the engine's system clock. The clock should be enabled when accessing
LCDIF registers, otherwise the kernel would hang up. We should also keep
the clock enabled when the engine is being active to scan out frames from
memory. This patch makes sure the axi clock is enabled when accessing
registers so that the kernel hang up issue can be fixed.
Reported-by: Peter Chen <peter.chen@freescale.com> Tested-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_any_context_irq() returns a negative value on failure.
It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success.
So fix testing return value of request_any_context_irq().
Also fixup the return value of devm_request_any_context_irq() to make it
consistent with request_any_context_irq().
Fixes: 0668d3065128 ("genirq: Add devm_request_any_context_irq()") Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although it is possible to let SRP I/O continue if a reconnect
results in a reduction of the number of channels, the current
code does not handle this scenario correctly. Instead of making
the reconnect code more complex, consider this as a reconnection
failure.
Reception of a DREQ message only causes the state of a single
channel to change. Hence move the 'connected' member variable
from the target to the channel data structure. This patch
avoids that following false positive warning can be reported
by srp_destroy_qp():
Fix a scsi_get_host() / scsi_host_put() imbalance in the error
path of srp_create_target(). See also patch "IB/srp: Avoid that
I/O hangs due to a cable pull during LUN scanning" (commit ID 34aa654ecb8e).
Avoid that srp_terminate_io() can get invoked while srp_queuecommand()
is in progress. This patch avoids that an I/O timeout can trigger the
following kernel warning:
Introduce the helper function srp_wait_for_queuecommand().
Move the definition of scsi_request_fn_active(). Add a comment
above srp_wait_for_queuecommand() that support for scsi-mq needs
to be added.
This patch does not change any functionality. A second call to
srp_wait_for_queuecommand() will be introduced in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: James Bottomley <JBottomley@Odin.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.
Fix the binding documentation so the property is properly specified.
Fixes: 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data") Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit df59fa7f4bca "spi: orion: support armada extended baud
rates" was too optimistic for the maximum baud rate that the Armada
SoCs can support. According to the hardware datasheet the maximum
frequency supported by the Armada 370 SoC is tclk/4. But for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
Currently the armada-370-spi compatible is only used by the Armada 370
and the Armada XP device tree. On Armada 370, tclk cannot be higher
than 200MHz. In order to be able to handle both SoCs, we can take the
minimum of 50MHz and tclk/4.
A proper solution is adding a compatible string for each SoC, but it
can't be done as a fix for compatibility reason (we can't modify
device tree that have been already released) and it will be part of a
separate patch.
Fixes: df59fa7f4bca (spi: orion: support armada extended baud rates) Reported-by: Kostya Porotchkin <kostap@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org> Suggested-by: Noralf Trønnes <noralf@tronnes.org> Tested-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list of loaded modules is walked through in
module_kallsyms_on_each_symbol (called by kallsyms_on_each_symbol). The
module_mutex lock should be acquired to prevent potential corruptions
in the list.
This was uncovered with new lockdep asserts in module code introduced by
the commit 0be964be0d45 ("module: Sanitize RCU usage and locking") in
recent next- trees.
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way the mask is generated in regmap_field_init() is wrong.
Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift
overflow while calculating the mask field.
On some 32 bits architectures, such as x86, the generated mask is 0,
instead of the expected 0xffffffff.
This patch uses GENMASK() to fix the problem, as this macro is already safe
regarding shift overflow.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In big endian mode regmap_bulk_read gives incorrect data
for byte reads.
This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.
Signed-off-by: Arun Chandran <achandran@mvista.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Since commit 077fcf116c8c ("mm/thp: allocate transparent hugepages on
local node"), we handle THP allocations on page fault in a special way -
for non-interleave memory policies, the allocation is only attempted on
the node local to the current CPU, if the policy's nodemask allows the
node.
This is motivated by the assumption that THP benefits cannot offset the
cost of remote accesses, so it's better to fallback to base pages on the
local node (which might still be available, while huge pages are not due
to fragmentation) than to allocate huge pages on a remote node.
The nodemask check prevents us from violating e.g. MPOL_BIND policies
where the local node is not among the allowed nodes. However, the
current implementation can still give surprising results for the
MPOL_PREFERRED policy when the preferred node is different than the
current CPU's local node.
In such case we should honor the preferred node and not use the local
node, which is what this patch does. If hugepage allocation on the
preferred node fails, we fall back to base pages and don't try other
nodes, with the same motivation as is done for the local node hugepage
allocations. The patch also moves the MPOL_INTERLEAVE check around to
simplify the hugepage specific test.
The difference can be demonstrated using in-tree transhuge-stress test
on the following 2-node machine where half memory on one node was
occupied to show the difference.
Number of successful THP allocations corresponds to free memory on node 0 in
the first case and node 1 in the second case, i.e. -p parameter is ignored and
cpu binding "wins".
After the patch:
> numactl -p0 -C0 ./transhuge-stress
transhuge-stress: 2.183 s/loop, 0.274 ms/page, 7295.516 MiB/s 7962 succeed, 0 failed, 1760 different pages
Beginning at commit d52d3997f843 ("ipv6: Create percpu rt6_info"), the
following INFO splat is logged:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc7-next-20150612 #1 Not tainted
-------------------------------
kernel/sched/core.c:7318 Illegal context switch in RCU-bh read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
3 locks held by systemd/1:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff815f0c8f>] rtnetlink_rcv+0x1f/0x40
#1: (rcu_read_lock_bh){......}, at: [<ffffffff816a34e2>] ipv6_add_addr+0x62/0x540
#2: (addrconf_hash_lock){+...+.}, at: [<ffffffff816a3604>] ipv6_add_addr+0x184/0x540
stack backtrace:
CPU: 0 PID: 1 Comm: systemd Not tainted 4.1.0-rc7-next-20150612 #1
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
Call Trace:
dump_stack+0x4c/0x6e
lockdep_rcu_suspicious+0xe7/0x120
___might_sleep+0x1d5/0x1f0
__might_sleep+0x4d/0x90
kmem_cache_alloc+0x47/0x250
create_object+0x39/0x2e0
kmemleak_alloc_percpu+0x61/0xe0
pcpu_alloc+0x370/0x630
Additional backtrace lines are truncated. In addition, the above splat
is followed by several "BUG: sleeping function called from invalid
context at mm/slub.c:1268" outputs. As suggested by Martin KaFai Lau,
these are the clue to the fix. Routine kmemleak_alloc_percpu() always
uses GFP_KERNEL for its allocations, whereas it should follow the gfp
from its callers.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Tejun Heo <tj@kernel.org> Cc: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kmemleak scanning thread can run for minutes. Callbacks like
kmemleak_free() are allowed during this time, the race being taken care
of by the object->lock spinlock. Such lock also prevents a memory block
from being freed or unmapped while it is being scanned by blocking the
kmemleak_free() -> ... -> __delete_object() function until the lock is
released in scan_object().
When a kmemleak error occurs (e.g. it fails to allocate its metadata),
kmemleak_enabled is set and __delete_object() is no longer called on
freed objects. If kmemleak_scan is running at the same time,
kmemleak_free() no longer waits for the object scanning to complete,
allowing the corresponding memory block to be freed or unmapped (in the
case of vfree()). This leads to kmemleak_scan potentially triggering a
page fault.
This patch separates the kmemleak_free() enabling/disabling from the
overall kmemleak_enabled nob so that we can defer the disabling of the
object freeing tracking until the scanning thread completed. The
kmemleak_free_part() is deliberately ignored by this patch since this is
only called during boot before the scanning thread started.
When building the kernel with a bare-metal (ELF) toolchain, the -shared
option may not be passed down to collect2, resulting in silent corruption
of the vDSO image (in particular, the DYNAMIC section is omitted).
The effect of this corruption is that the dynamic linker fails to find
the vDSO symbols and libc is instead used for the syscalls that we
intended to optimise (e.g. gettimeofday). Functionally, there is no
issue as the sigreturn trampoline is still intact and located by the
kernel.
This patch fixes the problem by explicitly passing -shared to the linker
when building the vDSO.
Reported-by: Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by: James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.
This may cause memmap entries that are in use to get freed.
In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.
This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.
This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6c81fe7925cc4c42 ("arm64: enable context tracking") did not
update el0_sp_pc to use ct_user_exit, but this appears to have been
unintentional. In commit 6ab6463aeb5fbc75 ("arm64: adjust el0_sync so
that a function can be called") we made x0 available, and in the return
to userspace we call ct_user_enter in the kernel_exit macro.
Due to this, we currently don't correctly inform RCU of the user->kernel
transition, and may erroneously account for time spent in the kernel as
if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING
is enabled.
As we do record the kernel->user transition, a userspace application
making accesses from an unaligned stack pointer can demonstrate the
imbalance, provoking the following warning:
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.
Fix the hbm power gating state machine so it will wait till it receives
confirmation interrupt for the PG_ISOLATION_EXIT message.
In process of the suspend flow the devices first have to exit from the
power gating state (runtime pm resume).
If we do not handle the confirmation interrupt after sending
PG_ISOLATION_EXIT message, we may receive it already after the suspend
flow has changed the device state and interrupt will be interpreted as a
spurious event, consequently link reset will be invoked which will
prevent the device from completing the suspend flow
kernel: [6603] mei_reset:136: mei_me 0000:00:16.0: powering down: end of reset
kernel: [476] mei_me_irq_thread_handler:643: mei_me 0000:00:16.0: function called after ISR to handle the interrupt processing.
kernel: mei_me 0000:00:16.0: FW not ready: resetting
- arch_spin_lock/unlock were lacking the ACQUIRE/RELEASE barriers
Since ARCv2 only provides load/load, store/store and all/all, we need
the full barrier
- LLOCK/SCOND based atomics, bitops, cmpxchg, which return modified
values were lacking the explicit smp barriers.
- Non LLOCK/SCOND varaints don't need the explicit barriers since that
is implicity provided by the spin locks used to implement the
critical section (the spin lock barriers in turn are also fixed in
this commit as explained above
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make 3.81 doesn't have the 'undefine' command. Using undefine
to clear LDFLAGS fails when make version 3.81 is used. Fix it
to use override to clear LDFLAGS.
Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.
Fixes: f25c0ae2b4c4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 73f7d1ca3263 "ACPI / init: Run acpi_early_init() before
timekeeping_init()" moved the ACPI subsystem initialization,
including the ACPI mode enabling, to an earlier point in the
initialization sequence, to allow the timekeeping subsystem
use ACPI early. Unfortunately, that resulted in boot regressions
on some systems and the early ACPI initialization was moved toward
its original position in the kernel initialization code by commit c4e1acbb35e4 "ACPI / init: Invoke early ACPI initialization later".
However, that turns out to be insufficient, as boot is still broken
on the Tyan S8812 mainboard.
To fix that issue, split the ACPI early initialization code into
two pieces so the majority of it still located in acpi_early_init()
and the part switching over the platform into the ACPI mode goes into
a new function, acpi_subsystem_init(), executed at the original early
ACPI initialization spot.
That fixes the Tyan S8812 boot problem, but still allows ACPI
tables to be loaded earlier which is useful to the EFI code in
efi_enter_virtual_mode().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97141 Fixes: 73f7d1ca3263 "ACPI / init: Run acpi_early_init() before timekeeping_init()" Reported-and-tested-by: Marius Tolzmann <tolzmann@molgen.mpg.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Toshi Kani <toshi.kani@hp.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Thinkpad X250, when attached to a dock, has two headphone outs but
no line out. Make sure we don't try to turn this into one headphone
and one line out (since that disables the headphone amp on the dock).
The pcm_class sysfs of each PCM substream gives only "none" since the
recent code change to embed the struct device. Fix the code to point
directly to the embedded device object properly.
Disable write buffering on the Toshiba ToPIC95 if it is enabled by
somebody (it is not supposed to be a power-on default according to
the datasheet). On the ToPIC95, practically no 32-bit Cardbus card
will work under heavy load without locking up the whole system if
this is left enabled. I tried about a dozen. It does not affect
16-bit cards. This is similar to the O2 bugs in early controller
revisions it seems.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961 Signed-off-by: Ryan C. Underwood <nemesis@icequake.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If, at the time __rcu_process_callbacks() is invoked, there are callbacks
in Tiny RCU's callback list, but none of them are ready to be invoked,
the current list-management code will knit the non-ready callbacks out
of the list. This can result in hangs and possibly worse. This commit
therefore inserts a check for there being no callbacks that can be
invoked immediately.
This bug is unlikely to occur -- you have to get a new callback between
the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to
__rcu_process_callbacks(). It was detected by the addition of RCU-bh
testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's
mutation testing. Although this bug was made much more likely by 915e8a4fe45e (rcu: Remove fastpath from __rcu_process_callbacks()), this
did not cause the bug, but rather made it much more probable. That
said, it takes more than 40 hours of rcutorture testing, on average,
for this bug to appear, so this fix cannot be considered an emergency.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined
so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq
desc's wake_depth unbalanced warning during system resume phase from the
gpio_keys driver, which is the driver for the power button of the ASUS
T100 laptop.
Ignore an existing mount if the locked readonly, nodev or atime
attributes are less permissive than the desired attributes
of the new mount.
On success ensure the new mount locks all of the same readonly, nodev and
atime attributes as the old mount.
The nosuid and noexec attributes are not checked here as this change
is destined for stable and enforcing those attributes causes a
regression in lxc and libvirt-lxc where those applications will not
start and there are no known executables on sysfs or proc and no known
way to create exectuables without code modifications
Fixes: e51db73532955 ("userns: Better restrictions on when proc and sysfs can be mounted") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fresh mounts of proc and sysfs are a very special case that works very
much like a bind mount. Unfortunately the current structure can not
preserve the MNT_LOCK... mount flags. Therefore refactor the logic
into a form that can be modified to preserve those lock bits.
Add a new filesystem flag FS_USERNS_VISIBLE that requires some mount
of the filesystem be fully visible in the current mount namespace,
before the filesystem may be mounted.
Move the logic for calling fs_fully_visible from proc and sysfs into
fs/namespace.c where it has greater access to mount namespace state.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fs_fully_visible attempts to make fresh mounts of proc and sysfs give
the mounter no more access to proc and sysfs than if they could have
by creating a bind mount. One aspect of proc and sysfs that makes
this particularly tricky is that there are other filesystems that
typically mount on top of proc and sysfs. As those filesystems are
mounted on empty directories in practice it is safe to ignore them.
However testing to ensure filesystems are mounted on empty directories
has not been something the in kernel data structures have supported so
the current test for an empty directory which checks to see
if nlink <= 2 is a bit lacking.
proc and sysfs have recently been modified to use the new empty_dir
infrastructure to create all of their dedicated mount points. Instead
of testing for S_ISDIR(inode->i_mode) && i_nlink <= 2 to see if a
directory is empty, test for is_empty_dir_inode(inode). That small
change guaranteess mounts found on proc and sysfs really are safe to
ignore, because the directories are not only empty but nothing can
ever be added to them. This guarantees there is nothing to worry
about when mounting proc and sysfs.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add two functions sysfs_create_mount_point and
sysfs_remove_mount_point that hang a permanently empty directory off
of a kobject or remove a permanently emptpy directory hanging from a
kobject. Export these new functions so modular filesystems can use
them.
To ensure it is safe to mount proc and sysfs I need to check if
filesystems that are mounted on top of them are mounted on truly empty
directories. Given that some directories can gain entries over time,
knowing that a directory is empty right now is insufficient.
Therefore add supporting infrastructure for permantently empty
directories that proc and sysfs can use when they create mount points
for filesystems and fs_fully_visible can use to test for permanently
empty directories to ensure that nothing will be gained by mounting a
fresh copy of proc or sysfs.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e4502c63f56aeca88 (ufs: deal with nfsd/iget races) made ufs
create inodes with I_NEW flag set. However ufs_mkdir() never cleared
this flag. Thus if someone ever tried to lookup the directory by inode
number, he would deadlock waiting for I_NEW to be cleared. Luckily this
mostly happens only if the filesystem is exported over NFS since
otherwise we have the inode attached to dentry and don't look it up by
inode number. In rare cases dentry can get freed without inode being
freed and then we'd hit the deadlock even without NFS export.
Fix the problem by clearing I_NEW before instantiating new directory
inode.
Fixes: e4502c63f56aeca887ced37f24e0def1ef11cec8 Reported-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e4502c63f56aeca88 (ufs: deal with nfsd/iget races) introduced
unlock_new_inode() call into ufs_add_nondir(). However that function
gets called also from ufs_link() which hands it already initialized
inode and thus unlock_new_inode() complains. The problem is harmless but
annoying.
Fix the problem by opencoding necessary stuff in ufs_link()
Fixes: e4502c63f56aeca887ced37f24e0def1ef11cec8 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limit the mounts fs_fully_visible considers to locked mounts.
Unlocked can always be unmounted so considering them adds hassle
but no security benefit.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The warning message in prepend_path is unclear and outdated. It was
added as a warning that the mechanism for generating names of pseudo
files had been removed from prepend_path and d_dname should be used
instead. Unfortunately the warning reads like a general warning,
making it unclear what to do with it.
Remove the warning. The transition it was added to warn about is long
over, and I added code several years ago which in rare cases causes
the warning to fire on legitimate code, and the warning is now firing
and scaring people for no good reason.
Reported-by: Ivan Delalande <colona@arista.com> Reported-by: Omar Sandoval <osandov@osandov.com> Fixes: f48cfddc6729e ("vfs: In d_path don't call d_dname on a mount point") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0244756edc4b98c ("ufs: sb mutex merge + mutex_destroy") generated
deadlocks in read/write mode on mkdir.
This patch partially reverts it keeping fixes by Andrew Morton and
mutex_destroy()
[AV: fixed a missing bit in ufs_remount()]
Signed-off-by: Fabian Frederick <fabf@skynet.be> Reported-by: Ian Campbell <ian.campbell@citrix.com> Suggested-by: Jan Kara <jack@suse.cz> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Evgeniy Dushistov <dushistov@mail.ru> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Roger Pau Monne <roger.pau@citrix.com> Cc: Ian Jackson <Ian.Jackson@eu.citrix.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9ef7db7f38d0 ("ufs: fix deadlocks introduced by sb
mutex merge") That patch tried to solve commit 0244756edc4b98c ("ufs: sb
mutex merge + mutex_destroy") which is itself partially reverted due to
multiple deadlocks.
Signed-off-by: Fabian Frederick <fabf@skynet.be> Suggested-by: Jan Kara <jack@suse.cz> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Evgeniy Dushistov <dushistov@mail.ru> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Roger Pau Monne <roger.pau@citrix.com> Cc: Ian Jackson <Ian.Jackson@eu.citrix.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
file_remove_suid() could mistakenly set S_NOSEC inode bit when root was
modifying the file. As a result following writes to the file by ordinary
user would avoid clearing suid or sgid bits.
Fix the bug by checking actual mode bits before setting S_NOSEC.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writes were a bit racy, but hard to turn into a bug at the same time.
(Particularly because modern Linux doesn't use this feature anymore.)
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Actually the next patch makes it much, much easier to trigger the race
so I'm including this one for stable@ as well. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric noticed problems with vhost-scsi and virtio-ccw: vhost-scsi
complained about overwriting values in the config space, which
was triggered by a broken implementation of virtio-ccw's config
get/set routines. It was probably sheer luck that we did not hit
this before.
When writing a value to the config space, the WRITE_CONF ccw will
always write from the beginning of the config space up to and
including the value to be set. If the config space up to the value
has not yet been retrieved from the device, however, we'll end up
overwriting values. Keep track of the known config space and update
if needed to avoid this.
Moreover, READ_CONF will only read the number of bytes it has been
instructed to retrieve, so we must not copy more than that to the
buffer, or we might overwrite trailing values.
Reported-by: Eric Farman <farman@linux.vnet.ibm.com> Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com> Tested-by: Eric Farman <farman@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The REGSET_VX_LOW ELF notes should contain the lower 64 bit halfes of the
first sixteen 128 bit vector registers. Unfortunately currently we copy
the upper halfes.
Fix this and correctly copy the lower halfes.
Fixes: a62bc0739253 ("s390/kdump: add support for vector extension") Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ea5f49692575 ("KVM: s390: only one external call may be pending
at a time") introduced a bug on machines that don't have SIGP
interpretation facility installed.
The injection of an external call will now always fail with -EBUSY
(if none is already pending).
This leads to the following symptoms:
- An external call will be injected but with the wrong "src cpu id",
as this id will not be remembered.
- The target vcpu will not be woken up, therefore the guest will hang if
it cannot deal with unexpected failures of the SIGP EXTERNAL CALL
instruction.
- If an external call is already pending, -EBUSY will not be reported.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM guest kernels for trap & emulate run in user mode, with a modified
set of kernel memory segments. However the fixmap address is still in
the normal KSeg3 region at 0xfffe0000 regardless, causing problems when
cache alias handling makes use of them when handling copy on write.
Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped
region when CONFIG_KVM_GUEST is defined.
The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign
resources correctly without the information from _CRS that tells us which
address ranges are claimed by which bridge. In the bugs mentioned below,
we incorrectly assign a sound card address (this example is from 1033299):
We enable _CRS on all systems from 2008 and later. On older systems, we
ignore _CRS and assume the whole physical address space (excluding RAM and
other devices) is available for PCI devices, but on systems that support
physical address spaces larger than 4GB, it's doubtful that the area above
4GB is really available for PCI.
After d56dbf5bab8c ("PCI: Allocate 64-bit BARs above 4G when possible"), we
try to use that space above 4GB *first*, so we're more likely to put a
device there.
On Juan's Toshiba Satellite Pro U200, BIOS left the graphics, sound, 1394,
and card reader devices unassigned (but only after Windows had been
booted). Only the sound device had a 64-bit BAR, so it was the only device
placed above 4GB, and hence the only device that didn't work.
Keep _CRS enabled even on pre-2008 systems if they support physical address
space larger than 4GB.
Fixes: d56dbf5bab8c ("PCI: Allocate 64-bit BARs above 4G when possible") Reported-and-tested-by: Juan Dayer <jdayer@outlook.com> Reported-and-tested-by: Alan Horsfield <alan@hazelgarth.co.uk> Link: https://bugzilla.kernel.org/show_bug.cgi?id=99221 Link: https://bugzilla.opensuse.org/show_bug.cgi?id=907092 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we take a PMU exception or a software event we call
perf_read_regs(). This overloads regs->result with a boolean that
describes if we should use the sampled instruction address register
(SIAR) or the regs.
If the exception is in kernel, we start with the kernel regs and
backtrace through the kernel stack. At this point we switch to the
userspace regs and backtrace the user stack with perf_callchain_user().
Unfortunately these regs have not got the perf_read_regs() treatment,
so regs->result could be anything. If it is non zero,
perf_instruction_pointer() decides to use the SIAR, and we get issues
like this:
On some archs, the local clockevent device stops in deep cpuidle states.
The broadcast framework is used to wakeup cpus in these idle states, in
which either an external clockevent device is used to send wakeup ipis
or the hrtimer broadcast framework kicks in in the absence of such a
device. One cpu is nominated as the broadcast cpu and this cpu sends
wakeup ipis to sleeping cpus at the appropriate time. This is the
implementation in the oneshot mode of broadcast.
In periodic mode of broadcast however, the presence of such cpuidle
states results in the cpuidle driver calling tick_broadcast_enable()
which shuts down the local clockevent devices of all the cpus and
appoints the tick broadcast device as the clockevent device for each of
them. This works on those archs where the tick broadcast device is a
real clockevent device. But on archs which depend on the hrtimer mode
of broadcast, the tick broadcast device hapens to be a pseudo device.
The consequence is that the local clockevent devices of all cpus are
shutdown and the kernel hangs at boot time in periodic mode.
Let us thus not register the cpuidle states which have
CPUIDLE_FLAG_TIMER_STOP flag set, on archs which depend on the hrtimer
mode of broadcast in periodic mode. This patch takes care of doing this
on powerpc. The cpus would not have entered into such deep cpuidle
states in periodic mode on powerpc anyway. So there is no loss here.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current Armada XP suspend to RAM implementation, as added in
commit 27432825ae19f ("ARM: mvebu: Armada XP GP specific
suspend/resume code") does not handle big-endian configurations
properly: the small bit of assembly code putting the DRAM in
self-refresh and toggling the GPIOs to turn off power forgets to
convert the values to little-endian.
This commit fixes that by making sure the two values we will write to
the DRAM controller register and GPIO register are already in
little-endian before entering the critical assembly code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 27432825ae19f ("ARM: mvebu: Armada XP GP specific suspend/resume code") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7232398abc6a ("ARM: tegra: Convert PMC to a driver") changed tegra_resume()
location storing from late to early and, as a result, broke suspend on Tegra20.
PMC scratch register 41 is used by tegra LP1 resume code for retrieving stored
physical memory address of common resume function and in the same time used by
tegra20_cpu_shutdown() (shared by Tegra20 cpuidle driver and platform SMP code),
which is storing CPU1 "resettable" status. It implies strict order of scratch
register usage, otherwise resume function address is lost on Tegra20 after
disabling non-boot CPU's on suspend. Fix it by storing "resettable" status in
IRAM instead of PMC scratch register.
According to the PSCI specification and the SMC/HVC calling
convention, PSCI function_ids that are not implemented must
return NOT_SUPPORTED as return value.
Current KVM implementation takes an unhandled PSCI function_id
as an error and injects an undefined instruction into the guest
if PSCI implementation is called with a function_id that is not
handled by the resident PSCI version (ie it is not implemented),
which is not the behaviour expected by a guest when calling a
PSCI function_id that is not implemented.
This patch fixes this issue by returning NOT_SUPPORTED whenever
the kvm PSCI call is executed for a function_id that is not
implemented by the PSCI kvm layer.
Cc: Christoffer Dall <christoffer.dall@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On VM entry, we disable access to the VFP registers in order to
perform a lazy save/restore of these registers.
On VM exit, we restore access, test if we did enable them before,
and save/restore the guest/host registers if necessary. In this
sequence, the FPEXC register is always accessed, irrespective
of the trapping configuration.
If the guest didn't touch the VFP registers, then the HCPTR access
has now enabled such access, but we're missing a barrier to ensure
architectural execution of the new HCPTR configuration. If the HCPTR
access has been delayed/reordered, the subsequent access to FPEXC
will cause a trap, which we aren't prepared to handle at all.
The same condition exists when trapping to enable VFP for the guest.
The fix is to introduce a barrier after enabling VFP access. In the
vmexit case, it can be relaxed to only takes place if the guest hasn't
accessed its view of the VFP registers, making the access to FPEXC safe.
The set_hcptr macro is modified to deal with both vmenter/vmexit and
vmtrap operations, and now takes an optional label that is branched to
when the guest hasn't touched the VFP registers.
Before calling into the filesystem, vfs_setxattr calls
security_inode_setxattr, which ends up calling selinux_inode_setxattr in
our case. That returns -EOPNOTSUPP whenever SBLABEL_MNT is not set.
SBLABEL_MNT was supposed to be set by sb_finish_set_opts, which sets it
only if selinux_is_sblabel_mnt returns true.
The selinux_is_sblabel_mnt logic was broken by eadcabc697e9 "SELinux: do
all flags twiddling in one place", which didn't take into the account
the SECURITY_FS_USE_NATIVE behavior that had been introduced for nfs
with eb9ae686507b "SELinux: Add new labeling type native labels".
This caused setxattr's of security labels over NFSv4.2 to fail.
Cc: Eric Paris <eparis@redhat.com> Cc: David Quigley <dpquigl@davequigley.com> Reported-by: Richard Chan <rc556677@outlook.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: added the stable dependency] Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 007bea098b86 (intel_pstate: Add setting voltage value for
baytrail P states.) introduced byt_set_pstate() with the assumption that
it would always be run by the CPU whose MSR is to be written by it. It
turns out, however, that is not always the case in practice, so modify
byt_set_pstate() to enforce the MSR write done by it to always happen on
the right CPU.
Fixes: 007bea098b86 (intel_pstate: Add setting voltage value for baytrail P states.) Signed-off-by: Joe Konno <joe.konno@intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dma mapping (dma_map_sg) fails in sdhci_pre_dma_transfer, -EINVAL
is returned. There are 3 callers of sdhci_pre_dma_transfer:
* sdhci_pre_req and sdhci_adma_table_pre: handle negative return
* sdhci_prepare_data: handles 0 (error) and "else" (good) only
So teach sdhci_prepare_data to understand negative return values from
sdhci_pre_dma_transfer and disable DMA in that case, as well as for
zero.
It was introduced in 348487cb28e66b032bae1b38424d81bf5b444408 (mmc:
sdhci: use pipeline mmc requests to improve performance). The commit
seems to be suspicious also by assigning host->sg_count both in
sdhci_pre_dma_transfer and sdhci_adma_table_pre.
Commit 83a60ed8f0b5 ("iommu/arm-smmu: fix ARM_SMMU_FEAT_TRANS_OPS
condition") accidentally negated the ID0_ATOSNS predicate in the ATOS
feature check, causing the driver to attempt ATOS requests on SMMUv2
hardware without the ATOS feature implemented.
This patch restores the predicate to the correct value.
The conversion to be16_add_cpu() is incorrect in case cryptlen is
negative due to premature (i.e. before addition / subtraction)
implicit conversion of cryptlen (int -> u16) leading to sign loss.
Fixes: 1d11911a8c57 ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function") Signed-off-by: Horia Geanta <horia.geanta@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ffs_closed can race with configfs_rmdir which will call config_item_release, so
add an extra check to avoid calling the unregister_gadget_item with an null
gadget item.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when copying to iter the size can be different then the iov count,
the check for full iov is wrong and make any read on request which
is not the exactly size of iov to return -EFAULT.
So, just check the success of the copy.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ethernet controller found in the Armada 370, 380 and 385 SoCs don't
support TCP/IP checksumming with frame sizes larger than 1600 bytes.
This patch fixes the issue by disabling the features NETIF_F_IP_CSUM and
NETIF_F_TSO for the Armada 370 and compatibles SoCs when the MTU is set
to a value greater than 1600 bytes.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Cc: <stable@vger.kernel.org> # v3.8+ Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the Ethernet DT nodes for Armada XP SoCs with the
compatible string "marvell,armada-xp-neta".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Fixes: 77916519cba3 ("arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces") Cc: <stable@vger.kernel.org> # v3.8+ Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvneta driver supports the Ethernet IP found in the Armada 370, XP,
380 and 385 SoCs. Since at least one more hardware feature is available
for the Armada XP SoCs then a way to identify them is needed.
This patch introduces a new compatible string "marvell,armada-xp-neta".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Cc: <stable@vger.kernel.org> # v3.8+ Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating Rx related buffers, alloc_pages is called using an order
number that is decreased until successful. A system under stress can
experience failures during this allocation process resulting in a warning
being issued. This message can be of concern to end users even though the
failure is not fatal. Since the failure is not fatal and can occur
multiple times, the driver should include the __GFP_NOWARN flag to
suppress the warning message from being issued.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is NULL pointer dereference possible during statistics update if the route
used for OOTB responce is removed at unfortunate time. If the route exists when
we receive OOTB packet and we finally jump into sctp_packet_transmit() to send
ABORT, but in the meantime route is removed under our feet, we take "no_route"
path and try to update stats with IP_INC_STATS(sock_net(asoc->base.sk), ...).
But sctp_ootb_pkt_new() used to prepare responce packet doesn't call
sctp_transport_set_owner() and therefore there is no asoc associated with this
packet. Probably temporary asoc just for OOTB responces is overkill, so just
introduce a check like in all other places in sctp_packet_transmit(), where
"asoc" is dereferenced.
To reproduce this, one needs to
0. ensure that sctp module is loaded (otherwise ABORT is not generated)
1. remove default route on the machine
2. while true; do
ip route del [interface-specific route]
ip route add [interface-specific route]
done
3. send enough OOTB packets (i.e. HB REQs) from another host to trigger ABORT
responce
As bnx2x_init_ptp() is only called if bp->flags contains PTP_SUPPORTED,
we also need to guard bnx2x_stop_ptp() with same condition, otherwise
ptp_task workqueue is not initialized and kernel barfs on
cancel_work_sync()
Fixes: eeed018cbfa30 ("bnx2x: Add timestamping and PTP hardware clock support") Reported-by: Michel Lespinasse <walken@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Michal Kalderon <Michal.Kalderon@qlogic.com> Cc: Ariel Elior <Ariel.Elior@qlogic.com> Cc: Yuval Mintz <Yuval.Mintz@qlogic.com> Cc: David Decotigny <decot@google.com> Acked-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in HA mode, the driver exposes an IB (RoCE) device instance with only
one port. Under SRIOV, the existing implementation doesn't go well with
the PF RoCE driver's role of Special QPs Para-Virtualization, etc.
As such, disable HA for the mlx4 PF RoCE device in SRIOV mode.
Fixes: a57500903093 ('IB/mlx4: Add port aggregation support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log