3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by: Tóth Attila <atoth@atoth.sote.hu> Tested-by: Tóth Attila <atoth@atoth.sote.hu> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface")
made the number of UARTs dynamic if LEFI_FIRMWARE_INTERFACE is configured.
Unfortunately, it did not initialize the number of UARTs if
LEFI_FIRMWARE_INTERFACE is not configured. As a result, the Fulong2e
system has no console.
Kernels after v3.9 use kmalloc_size(INDEX_NODE + 1) to get the next
larger cache size than the size index INDEX_NODE mapping. In kernels
3.9 and earlier we used malloc_sizes[INDEX_L3 + 1].cs_size.
However, sometimes we can't get the right output we expected via
kmalloc_size(INDEX_NODE + 1), causing a BUG().
The mapping table in the latest kernel is like:
index = {0, 1, 2 , 3, 4, 5, 6, n}
size = {0, 96, 192, 8, 16, 32, 64, 2^n}
The mapping table before 3.10 is like this:
index = {0 , 1 , 2, 3, 4 , 5 , 6, n}
size = {32, 64, 96, 128, 192, 256, 512, 2^(n+3)}
The problem on my mips64 machine is as follows:
(1) When configured DEBUG_SLAB && DEBUG_PAGEALLOC && DEBUG_LOCK_ALLOC
&& DEBUG_SPINLOCK, the sizeof(struct kmem_cache_node) will be "150",
and the macro INDEX_NODE turns out to be "2": #define INDEX_NODE
kmalloc_index(sizeof(struct kmem_cache_node))
(2) Then the result of kmalloc_size(INDEX_NODE + 1) is 8.
(3) Then "if(size >= kmalloc_size(INDEX_NODE + 1)" will lead to "size
= PAGE_SIZE".
(4) Then "if ((size >= (PAGE_SIZE >> 3))" test will be satisfied and
"flags |= CFLGS_OFF_SLAB" will be covered.
(5) if (flags & CFLGS_OFF_SLAB)" test will be satisfied and will go to
"cachep->slabp_cache = kmalloc_slab(slab_size, 0u)", and the result
here may be NULL while kernel bootup.
(6) Finally,"BUG_ON(ZERO_OR_NULL_PTR(cachep->slabp_cache));" causes the
BUG info as the following shows (may be only mips64 has this problem):
This patch fixes the problem of kmalloc_size(INDEX_NODE + 1) and removes
the BUG by adding 'size >= 256' check to guarantee that all necessary
small sized slabs are initialized regardless sequence of slab size in
mapping table.
Fixes: e33660165c90 ("slab: Use common kmalloc_index/kmalloc_size...") Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by: Liuhailong <liu.hailong6@zte.com.cn> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel may delay interrupts for a long time which can result in timers
being delayed. If this occurs the intel_pstate driver will crash with a
divide by zero error:
The duration between reads of the APERF and MPERF registers overflowed a s32
sized integer in intel_pstate_get_scaled_busy()'s call to div_fp(). The result
is that int_tofp(duration_us) == 0, and the kernel attempts to divide by 0.
While the kernel shouldn't be delaying for a long time, it can and does
happen and the intel_pstate driver should not panic in this situation. This
patch changes the div_fp() function to use div64_s64() to allow for "long"
division. This will avoid the overflow condition on long delays.
[v2]: use div64_s64() in div_fp()
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Renninger <trenn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If atmel_init_gpios fails the port has already been marked as busy (in
line 2629), so this must be undone in the error path.
This bug was introduced because I created the patch that finally
became 722ccf416ac2 ("serial: atmel: fix error handling when
mctrl_gpio_init fails") on top of 3.19 which didn't have commit 6fbb9bdf0f3f ("tty/serial: at91: fix error handling in
atmel_serial_probe()") yet.
This adds an entry to the uart_config table for PORT_RT2880
enabling rx/tx FIFOs. The UART is actually a Palmchip BK-3103
which is found in several devices from Alchemy/RMI, Ralink, and
Sigma Designs.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be two problems causing this issue.
First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active(). However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
add_wait_queue(&tty->read_wait, &wait);
...
if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
ldata->read_head);
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
spin_lock_irqsave(&q->lock, flags);
/* from add_wait_queue() */
...
if (!input_available_p(tty, 0)) {
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
ldata->read_head);
if (waitqueue_active(&tty->read_wait))
__add_wait_queue(q, wait);
spin_unlock_irqrestore(&q->lock,flags);
/* from add_wait_queue() */
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.
This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation). Moreover, the resulting code is much simpler.
Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leandro Awa writes:
"After switching to version 4.1.6, our parallelized and distributed
workflows now fail consistently with errors of the form:
T34: ./regex.c:39:22: error: config.h: No such file or directory
From our 'git bisect' testing, the following commit appears to be the
possible cause of the behavior we've been seeing: commit 766c4cbfacd8"
Al Viro says:
"What happens is that 766c4cbfacd8 got the things subtly wrong.
We used to treat d_is_negative() after lookup_fast() as "fall with
ENOENT". That was wrong - checking ->d_flags outside of ->d_seq
protection is unreliable and failing with hard error on what should've
fallen back to non-RCU pathname resolution is a bug.
Unfortunately, we'd pulled the test too far up and ran afoul of
another kind of staleness. The dentry might have been absolutely
stable from the RCU point of view (and we might be on UP, etc), but
stale from the remote fs point of view. If ->d_revalidate() returns
"it's actually stale", dentry gets thrown away and the original code
wouldn't even have looked at its ->d_flags.
What we need is to check ->d_flags where 766c4cbfacd8 does (prior to
->d_seq validation) but only use the result in cases where we do not
discard this dentry outright"
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
Make file->f_path always point to the overlay dentry so that the path in
/proc/pid/fd is correct and to ensure that label-based LSMs have access to the
overlay as well as the underlay (path-based LSMs probably don't need it).
Using my union testsuite to set things up, before the patch I see:
Note the change in where /proc/$$/fd/5 points to in the ls command. It was
pointing to /a/foo107 (which doesn't exist) and now points to /mnt/a/foo107
(which is correct).
The inode accessed, however, is the lower layer. The union layer is on device
25h/37d and the upper layer on 24h/36d.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: "Kamata, Munehisa" <kamatam@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call ovl_drop_write() earlier in ovl_dentry_open() before we call vfs_open()
as we've done the copy up for which we needed the freeze-write lock by that
point.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: "Kamata, Munehisa" <kamatam@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c0b ("Use separate bitmaps for each nodes in the cluster") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per-IRQ directories in procfs are created only when a handler is first
added to the irqdesc, not when the irqdesc is created. In the case of
a shared IRQ, multiple tasks can race to create a directory. This
race condition seems to have been present forever, but is easier to
hit with async probing.
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Daniel J Blueman <daniel@numascale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chas Williams <3chas3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: "Kamata, Munehisa" <kamatam@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the compiler does not modify arguments of syscall functions.
This can happen if the compiler generates a tailcall to another
function. For example, without asmlinkage_protect sys_openat is compiled
into this function:
Note how the fourth argument is modified in place, modifying the register
%d4 that gets restored from this stack slot when the function returns to
user-space. The caller may expect the register to be unmodified across
system calls.
This is the arm64 portion of commit 45cac65b0fcd ("readahead: fault
retry breaks mmap file read random detection"), which was absent from
the initial port and has since gone unnoticed. The original commit says:
> .fault now can retry. The retry can break state machine of .fault. In
> filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
> try, since the page is in page cache now, ra->mmap_miss is decreased. And
> these are done in one fault, so we can't detect random mmap file access.
>
> Add a new flag to indicate .fault is tried once. In the second try, skip
> ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
With this change, Mark reports that:
> Random read improves by 250%, sequential read improves by 40%, and
> random write by 400% to an eMMC device with dm crypto wrapped around it.
Cc: Shaohua Li <shli@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Mark Salyzyn <salyzyn@android.com> Signed-off-by: Riley Andrews <riandrews@android.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because when using function graph tracer, if the traced
function return value is in multi regs ([x0-x7]), return_to_handler
may corrupt them. So in return_to_handler, the parameter regs should
be protected properly.
Signed-off-by: Li Bin <huawei.libin@huawei.com> Acked-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Properties Table feature introduced in UEFIv2.5 may
split memory regions that cover PE/COFF memory images into
separate code and data regions. Since these regions only differ
in the type (runtime code vs runtime data) and the permission
bits, but not in the memory type attributes (UC/WC/WT/WB), the
spec does not require them to be aligned to 64 KB.
Since the relative offset of PE/COFF .text and .data segments
cannot be changed on the fly, this means that we can no longer
pad out those regions to be mappable using 64 KB pages.
Unfortunately, there is no annotation in the UEFI memory map
that identifies data regions that were split off from a code
region, so we must apply this logic to all adjacent runtime
regions whose attributes only differ in the permission bits.
So instead of rounding each memory region to 64 KB alignment at
both ends, only round down regions that are not directly
preceded by another runtime region with the same type
attributes. Since the UEFI spec does not mandate that the memory
map be sorted, this means we also need to sort it first.
Note that this change will result in all EFI_MEMORY_RUNTIME
regions whose start addresses are not aligned to the OS page
size to be mapped with executable permissions (i.e., on kernels
compiled with 64 KB pages). However, since these mappings are
only active during the time that UEFI Runtime Services are being
invoked, the window for abuse is rather small.
Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Rutland <mark.rutland@arm.com> [UEFI 2.4 only] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Reviewed-by: Mark Salter <msalter@redhat.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Leif Lindholm <leif.lindholm@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/1443218539-7610-3-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rare cases a directory can be renamed out from under a bind mount.
In those cases without special handling it becomes possible to walk up
the directory tree to the root dentry of the filesystem and down
from the root dentry to every other file or directory on the filesystem.
Like division by zero .. from an unconnected path can not be given
a useful semantic as there is no predicting at which path component
the code will realize it is unconnected. We certainly can not match
the current behavior as the current behavior is a security hole.
Therefore when encounting .. when following an unconnected path
return -ENOENT.
- Add a function path_connected to verify path->dentry is reachable
from path->mnt.mnt_root. AKA to validate that rename did not do
something nasty to the bind mount.
To avoid races path_connected must be called after following a path
component to it's next path component.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rename can result in a dentry that by walking up d_parent
will never reach it's mnt_root. For lack of a better term
I call this an escaped path.
prepend_path is called by four different functions __d_path,
d_absolute_path, d_path, and getcwd.
__d_path only wants to see paths are connected to the root it passes
in. So __d_path needs prepend_path to return an error.
d_absolute_path similarly wants to see paths that are connected to
some root. Escaped paths are not connected to any mnt_root so
d_absolute_path needs prepend_path to return an error greater
than 1. So escaped paths will be treated like paths on lazily
unmounted mounts.
getcwd needs to prepend "(unreachable)" so getcwd also needs
prepend_path to return an error.
d_path is the interesting hold out. d_path just wants to print
something, and does not care about the weird cases. Which raises
the question what should be printed?
Given that <escaped_path>/<anything> should result in -ENOENT I
believe it is desirable for escaped paths to be printed as empty
paths. As there are not really any meaninful path components when
considered from the perspective of a mount tree.
So tweak prepend_path to return an empty path with an new error
code of 3 when it encounters an escaped path.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com> Fixes: 16b23787fc70 ("mmc: sdhci-of-arasan: Call OF parsing for MMC") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Signed-off-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the lockdep splat is a false positive, becuase path_openat holds i_mutex
of the parent directory and ubifs_init_security() tries to acquire i_mutex
of a new inode, it reveals that taking i_mutex in ubifs_init_security() is
in vain because it is only being called in the inode allocation path
and therefore nobody else can see the inode yet.
Reported-and-tested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-and-tested-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: dedekind1@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When replacing del_timer() with del_timer_sync(), I introduced
a deadlock condition :
reqsk_queue_unlink() is called from inet_csk_reqsk_queue_drop()
inet_csk_reqsk_queue_drop() can be called from many contexts,
one being the timer handler itself (reqsk_timer_handler()).
In this case, del_timer_sync() loops forever.
Simple fix is to test if timer is pending.
Fixes: 2235f2ac75fd ("inet: fix races with reqsk timers") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Holger Hoffstätte <holger.hoffstaette@googlemail.com> Cc: Andre Tomt <andre@tomt.net> Cc: Chris Caputo <ccaputo@alt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak") Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
Tolerance applies on both sides of the target voltage, i.e. both min and
max sides. But while checking if a voltage is supported by the regulator
or not, we haven't taken care of tolerance on the lower side. Fix that.
Cc: Lucas Stach <l.stach@pengutronix.de> Fixes: 045ee45c4ff2 ("cpufreq: cpufreq-dt: disable unsupported OPPs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cache_shared_cpu_map_setup() did check sibling CPUs cacheinfo descriptor
while the respective teardown path cache_shared_cpu_map_remove() didn't.
Fix that.
>From tglx's version: to be on the safe side, move the cacheinfo
descriptor check to free_cache_attributes(), thus cleaning up the
hotplug path a little and making this even more robust.
Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.
Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit 33c300cb90a6 ("usb: musb: dsps:
don't fake of_node to musb core") we have been
preventing CPPI 4.1 from probing due to NULL
of_node. We can't revert said commit otherwise
a different regression would show up, so the fix
is to look for the parent device's (glue layer's)
of_node instead, since that's the thing which
is actually described in DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpio-desc migration done in v4.0 caused a regression
with legacy boots due to reversed reset logic.
e.g. omap3-beagle USB host breaks on legacy boot.
Request the reset GPIO with GPIOF_ACTIVE_LOW flag so that
it matches the driver logic and pin behaviour.
Fixes: e9f2cefb0cdc ("usb: phy: generic: migrate to gpio_desc") Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spec, there are functional and protocol stalls.
For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).
For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).
It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.
Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the regression caused by commit ad78c918602 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c918602c ("usb: musb: dsps: just start polling already") Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The in kernel snprintf() will conveniently return the actual length of
the printed string even if not given an output beffer at all so just do
that rather than relying on the user to pass in a suitable buffer,
ensuring that we don't need to worry if the buffer was truncated due to
the size of the buffer passed in.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a read is attempted which is smaller than the line length then we may
underflow the subtraction we're doing with the unsigned size_t type so
move some of the calculation to be additions on the right hand side
instead in order to avoid this.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary check that disabled SIS pipe commands for SIS-32
devices. This change was sufficient to enable raw mode and send SIS
pipe commands for a 57B3 device.
Fixes: f8ee25d7d239 ("ipr: AF DASD raw mode implementation in ipr driver") Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the lack of clk_put() in sa11xx_base.c's error cleanup paths by
converting the driver to the devm_* API.
Fixes: 86d88bfca475 ("ARM: 8247/2: pcmcia: sa1100: make use of device clock") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d1c ("ath10k: unregister and remove frag_threshold callback") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In device_add_property_set() we check pset parameter for a NULL, but few lines
later we do a pointer arithmetic without check that will crash kernel in the
set_secondary_fwnode().
Here we check if pset parameter is NULL and return immediately.
Fixes: 16ba08d5c9ec (device property: Introduce firmware node type for platform data) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rockchip io-domain driver currently only depends on ARCH_ROCKCHIP
itself. This makes it possible to select the power-domain driver, but
not the POWER_AVS class and results in the iodomain-driver not getting
build in this case.
So add the additional dependency, which also results in the driver
config option now being placed nicely into the AVS submenu.
Fixes: 662a958638bd ("PM / AVS: rockchip-io: add driver handling Rockchip io domains") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USER_DATA register cannot be accessed using byte accessors on A13
SoCs, thus triggering a bug when using memcpy_toio on this register.
Declare an helper macros to convert an OOB buffer into a suitable
USER_DATA value and vice-versa.
This patch also fixes an error in the oob_required logic (some OOB data
are not written even if the user required it) by removing the
oob_required condition, which is perfectly valid since the core already
fill ->oob_poi with FFs when oob_required is false.
When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.
In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.
When the ITS is configured for non-cacheable transactions, make sure
that the allocated, zeroed memory is flushed to the Point of
Coherency, allowing the ITS to observe the zeros instead of random
garbage (or even get its own data overwritten by zeros being evicted
from the cache...).
Fixes: 241a386c7dbb "irqchip: gicv3-its: Use non-cacheable accesses when no shareability" Reported-and-tested-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Pavel Fedin <p.fedin@samsung.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1442142873-20213-3-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When masking/unmasking interrupts, mask_cache is updated and used later
for suspend/resume. Unfortunately, it always was the mask_cache
associated with the first irq chip which was updated. So when performing
resume, only irqs 0-31 could be enabled.
Linux cifs mount with ntlmssp against an Mac OS X (Yosemite
10.10.5) share fails in case the clocks differ more than +/-2h:
digest-service: digest-request: od failed with 2 proto=ntlmv2
digest-service: digest-request: kdc failed with -1561745592 proto=ntlmv2
Fix this by (re-)using the given server timestamp for the
ntlmv2 authentication (as Windows 7 does).
A related problem was also reported earlier by Namjae Jaen (see below):
Windows machine has extended security feature which refuse to allow
authentication when there is time difference between server time and
client time when ntlmv2 negotiation is used. This problem is prevalent
in embedded enviornment where system time is set to default 1970.
Modern servers send the server timestamp in the TargetInfo Av_Pair
structure in the challenge message [see MS-NLMP 2.2.2.1]
In [MS-NLMP 3.1.5.1.2] it is explicitly mentioned that the client must
use the server provided timestamp if present OR current time if it is
not
Reported-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
The only user of this driver that has not been converted to fully
device tree is the i.MX35 SoC.
There is a i.MX35-based board (mach-pcm043.c) that uses platform data
to pass wp_gpio and cd_gpio information.
Commit 8d86e4fcccf61ba ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
broke the platform data case by removing mmc_gpio_request_ro() and
mmc_gpio_request_cd(), so restore the functionality for the non-dt
case.
Also, restore the check for ESDHC_CD_CONTROLLER so that we can still
support the "fsl,cd-controller" property.
As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.
On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.
In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.
Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.
What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
The tt_local_entry deletion performed in batadv_tt_local_remove() was neither
protecting against simultaneous deletes nor checking whether the element was
still part of the list before calling hlist_del_rcu().
Replacing the hlist_del_rcu() call with batadv_hash_remove() provides adequate
protection via hash spinlocks as well as an is-element-still-in-hash check to
avoid 'blind' hash removal.
Commit 11c32d7b6274cb0f554943d65bd4a126c4a86dcd
"video: move Versatile CLCD helpers" missed the fact
that the Integrator/CP is also using the helper, and
as a result the platform got only stubs and no graphics.
Add this as a default selection to Kconfig so we have
graphics again.
It is possible that we bind against a local socket in early_demux when we
are actually going to want to forward it. In this case, the socket serves
no purpose and only serves to confuse things (particularly functions which
implicitly expect sk_fullsock to be true, like ip_local_out).
Additionally, skb_set_owner_w is totally broken for non full-socks.
Signed-off-by: Alex Gartrell <agartrell@fb.com> Fixes: 41063e9dd119 ("ipv4: Early TCP socket demux.") Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I overlooked the svc->sched_data usage from schedulers
when the services were converted to RCU in 3.10. Now
the rare ipvsadm -E command can change the scheduler
but due to the reverse order of ip_vs_bind_scheduler
and ip_vs_unbind_scheduler we provide new sched_data
to the old scheduler resulting in a crash.
To fix it without changing the scheduler methods we
have to use synchronize_rcu() only for the editing case.
It means all svc->scheduler readers should expect a
NULL value. To avoid breakage for the service listing
and ipvsadm -R we can use the "none" name to indicate
that scheduler is not assigned, a state when we drop
new connections.
Reported-by: Alexander Vasiliev <a.vasylev@404-group.com> Fixes: ceec4c381681 ("ipvs: convert services to rcu") Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Vallaly reports about wrong source address used
in rare cases for tunneled traffic. Looks like
__ip_vs_get_out_rt in 3.10+ is providing uninitialized
dest_dst->dst_saddr.ip because ip_vs_dest_dst_alloc uses
kmalloc. While we retry after seeing EINVAL from routing
for data that does not look like valid local address, it
still succeeded when this memory was previously used from
other dests and with different local addresses. As result,
we can use valid local address that is not suitable for
our real server.
Fix it by providing 0.0.0.0 every time our cache is refreshed.
By this way we will get preferred source address from routing.
Reported-by: Michael Vallaly <lvs@nolatency.com> Fixes: 026ace060dfe ("ipvs: optimize dst usage for real server") Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Martin [Fri, 24 Jul 2015 16:39:21 +0000 (17:39 +0100)]
serial/amba-pl011: Disable interrupts around TX softirq
pl011_tx_softirq() currently uses spin_{,un}lock(), which are not
sufficient to inhibit pl011_int() from being triggered by a local
IRQ and trying to re-take the same lock. This can lead to
deadlocks.
This patch uses the _irq() locking variants instead to ensure that
pl011_int() handling for a given port is deferred until any
pl011_tx_softirq() work for that port is complete.
Notes for stable:
This patch fixes an issue that is fixed by the following upstream
commit, which is a more substantial rewrite of the affected code,
fixing multiple, mostly more minor issues:
The upstream patch was rejected for stable on the reasonable grounds
that it was too big and complex a patch. The original buggy code was
merged in v4.1, and the rewrite was merged in v4.2, leaving only v4.1
affected.
The optimized task selection logic optimistically selects a new task
to run without first doing a full put_prev_task(). This is so that we
can avoid a put/set on the common ancestors of the old and new task.
Similarly, we should only call check_cfs_rq_runtime() to throttle
eligible groups if they're part of the common ancestry, otherwise it
is possible to end up with no eligible task in the simple task
selection.
Imagine:
/root
/prev /next
/A /B
If our optimistic selection ends up throttling /next, we goto simple
and our put_prev_task() ends up throttling /prev, after which we're
going to bug out in set_next_entity() because there aren't any tasks
left.
Avoid this scenario by only throttling common ancestors.
Reported-by: Mohammed Naser <mnaser@vexxhost.com> Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Ben Segall <bsegall@google.com>
[ munged Changelog ] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Roman Gushchin <klamm@yandex-team.ru> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: pjt@google.com Fixes: 678d5718d8d0 ("sched/fair: Optimize cgroup pick_next_task_fair()") Link: http://lkml.kernel.org/r/xm26wq1oswoq.fsf@sword-of-the-dawn.mtv.corp.google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dmitry Vyukov, we really shouldn't do ipc_addid() before
having initialized the IPC object state. Yes, we initialize the IPC
object in a locked state, but with all the lockless RCU lookup work,
that IPC object lock no longer means that the state cannot be seen.
We already did this for the IPC semaphore code (see commit e8577d1f0329:
"ipc/sem.c: fully initialize sem_array before making it visible") but we
clearly forgot about msg and shm.
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Don't check if timer is running with a timer_pending() before
deleting it with del_timer_sync(), this defies the whole point of
the sync part and can cause a possible race.
Instead we just want to make sure the timer is initialized early enough
before we have a chance to delete it.
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
During quick plug/removal of OTG adapter during dual-role testing
it can happen that xhci_alloc_device() is called for the newly
detected device after the DRD library has called xhci_stop to
remove the HCD.
If that is the case, just fail early to prevent the following warning.
[ 154.732649] hub 4-0:1.0: USB hub found
[ 154.742204] hub 4-0:1.0: 1 port detected
[ 154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 155.043315] usb usb4: USB disconnect, device number 1
[ 155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop
[ 155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered
[ 155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 155.071710] usb usb3: USB disconnect, device number 1
[ 155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.082389] ------------[ cut here ]------------
[ 155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]()
[ 155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc
[ 155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G W 4.1.4-00834-gcd9380b-dirty #50
[ 155.156073] Hardware name: Generic AM43 (Flattened Device Tree)
[ 155.162117] Workqueue: usb_hub_wq hub_event [usbcore]
[ 155.167249] Backtrace:
[ 155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c)
[ 155.177390] r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000
[ 155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0)
[ 155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc)
[ 155.198605] r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000
[ 155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c)
[ 155.213202] r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000
[ 155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd])
[ 155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd])
[ 155.240415] r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002
[ 155.248363] r4:ee49f000
[ 155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore])
[ 155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore])
[ 155.270874] r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001
[ 155.278822] r4:00000000
[ 155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340)
[ 155.290196] r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314
[ 155.298151] r4:ee434380
[ 155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c)
[ 155.308963] r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400
[ 155.316913] r4:eeec5414
[ 155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8)
[ 155.326765] r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0
[ 155.334713] r4:00000000 r3:00000000
[ 155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c)
[ 155.345626] r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0
[ 155.356108] ---[ end trace a58d34c223b190e6 ]---
[ 155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1!
[ 155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.579667] ------------[ cut here ]------------
Fix potential null-pointer dereference at probe by making sure that the
required endpoints are present.
The whiteheat driver assumes there are at least five pairs of bulk
endpoints, of which the final pair is used for the "command port". An
attempt to bind to an interface with fewer bulk endpoints would
currently lead to an oops.
we validate the mstb structs in the work function, and doing
that takes a reference. So we should never get here with the
work function running using the mstb device, only if the work
function hasn't run yet or is running for another mstb.
So we don't need to sync the work here, this was causing
lockdep spew as below.
[ +0.000160] =============================================
[ +0.000001] [ INFO: possible recursive locking detected ]
[ +0.000002] 3.10.0-320.el7.rhel72.stable.backport.3.x86_64.debug #1 Tainted: G W ------------
[ +0.000001] ---------------------------------------------
[ +0.000001] kworker/4:2/1262 is trying to acquire lock:
[ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b29a5>] flush_work+0x5/0x2e0
[ +0.000007]
but task is already holding lock:
[ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710
[ +0.000004]
other info that might help us debug this:
[ +0.000001] Possible unsafe locking scenario:
Instead of only enabling the backlight (which seems to set it to max
brightness), just re-set the current backlight level, which also takes
care of enabling the backlight if necessary.
Only the radeon_atom_encoder_dpms_dig part tested on a Kaveri laptop,
the radeon_atom_encoder_dpms_avivo part is only compile tested.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've done some extensive history digging across libdrm, mesa and
xf86-video-{intel,nouveau,ati}. The only potential user of this with
kms drivers I could find was ttmtest, which once used drmGetLock
still. But that mistake was quickly fixed up. Even the intel xvmc
library (which otherwise was really good with using dri1 stuff in kms
mode) managed to never take the hw lock for dri2 (and hence kms).
Hence it should be save to unconditionally disallow this.
Cc: Peter Antoine <peter.antoine@intel.com> Reviewed-by: Peter Antoine <peter.antoine@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VBT MIPI Sequence Block version 3 has forward incompatible changes:
First, the block size in the header has been specified reserved, and the
actual size is a separate 32-bit value within the block. The current
find_section() function to will only look at the size in the block
header, and, depending on what's in that now reserved size field,
continue looking for other sections in the wrong place.
Fix this by taking the new block size field into account. This will
ensure that the lookups for other sections will work properly, as long
as the new 32-bit size does not go beyond the opregion VBT mailbox size.
Second, the contents of the block have been completely
changed. Gracefully refuse parsing the yet unknown data version.
Cc: Deepak M <m.deepak@intel.com> Reviewed-by: Deepak M <m.deepak@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log