The hardware always writes one or two bytes in the index portion of
an indexed transfer. Make sure the message we send as the index
doesn't have a zero length.
Cc: stable@vger.kernel.org Cc: Daniel Kurtz <djkurtz@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-3-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bb9e0d4bca50f429152e74a459160b41f3d60fb2) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
We can only specify the one slave address to indexed reads/writes.
Make sure the messages we check are destined to the same slave
address before deciding to do an indexed transfer.
Cc: stable@vger.kernel.org Cc: Daniel Kurtz <djkurtz@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-2-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit c4deb62d7821672265b87952bcd1c808f3bf3e8f) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
For correct close-to-open semantics, NFS must validate
the change attribute of a directory (or file) on open.
Since commit ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a
d_weak_revalidate dentry op"), open() of "." or a path ending ".." is
not revalidated reliably (except when that direct is a mount point).
Prior to that commit, "." was revalidated using nfs_lookup_revalidate()
which checks the LOOKUP_OPEN flag and forces revalidation if the flag is
set.
Since that commit, nfs_weak_revalidate() is used for NFSv3 (which
ignores the flags) and nothing is used for NFSv4.
This is fixed by using nfs_lookup_verify_inode() in
nfs_weak_revalidate(). This does the revalidation exactly when needed.
Also, add a definition of .d_weak_revalidate for NFSv4.
The incorrect behavior is easily demonstrated by running "echo *" in
some non-mountpoint NFS directory while watching network traffic.
Without this patch, "echo *" sometimes doesn't produce any traffic.
With the patch it always does.
Fixes: ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op")
cc: stable@vger.kernel.org (3.9+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c6539931 ("mtd: Add panic_write for NAND flashes") Cc: <stable@vger.kernel.org> Signed-off-by: Brent Taylor <motobud@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Fixes: d02fd93e2cd8 ("drm/panel: simple - Disable panel on shutdown") Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Jonathan Liu <net147@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170807115545.27747-1-net147@gmail.com Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the PTR macro, which conflicts with the PTR macro
in include/uapi/linux/bcache.h.
Sometimes, a processor might execute an instruction while another
processor is updating the page tables for that instruction's code page,
but before the TLB shootdown completes. The interesting case happens
if the page is in the TLB.
In general, the processor will succeed in executing the instruction and
nothing bad happens. However, what if the instruction is an MMIO access?
If *that* happens, KVM invokes the emulator, and the emulator gets the
updated page tables. If the update side had marked the code page as non
present, the page table walk then will fail and so will x86_decode_insn.
Unfortunately, even though kvm_fetch_guest_virt is correctly returning
X86EMUL_PROPAGATE_FAULT, x86_decode_insn's caller treats the failure as
a fatal error if the instruction cannot simply be reexecuted (as is the
case for MMIO). And this in fact happened sometimes when rebooting
Windows 2012r2 guests. Just checking ctxt->have_exception and injecting
the exception if true is enough to fix the case.
Thanks to Eduardo Habkost for helping in the debugging of this issue.
Instruction emulation after trapping a #UD exception can result in an
MMIO access, for example when emulating a MOVBE on a processor that
doesn't support the instruction. In this case, the #UD vmexit handler
must exit to user mode, but there wasn't any code to do so. Add it for
both VMX and SVM.
Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When guest passes KVM it's pvclock-page GPA via WRMSR to
MSR_KVM_SYSTEM_TIME / MSR_KVM_SYSTEM_TIME_NEW, KVM don't initialize
pvclock-page to some start-values. It just requests a clock-update which
will happen before entering to guest.
The clock-update logic will call kvm_setup_pvclock_page() to update the
pvclock-page with info. However, kvm_setup_pvclock_page() *wrongly*
assumes that the version-field is initialized to an even number. This is
wrong because at first-time write, field could be any-value.
Fix simply makes sure that if first-time version-field is odd, increment
it once more to make it even and only then start standard logic.
This follows same logic as done in other pvclock shared-pages (See
kvm_write_wall_clock() and record_steal_time()).
We discovered a box that had double allocations, and suspected the space
cache may be to blame. While auditing the write out path I noticed that
if we've already setup the space cache we will just carry on. This
means that any error we hit after cache_save_setup before we go to
actually write the cache out we won't reset the inode generation, so
whatever was already written will be considered correct, except it'll be
stale. Fix this by _always_ resetting the generation on the block group
inode, this way we only ever have valid or invalid cache.
With this patch I was no longer able to reproduce cache corruption with
dm-log-writes and my bpf error injection tool.
Cc: stable@vger.kernel.org Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
MADVISE_WILLNEED has always been a noop for DAX (formerly XIP) mappings.
Unfortunately madvise_willneed() doesn't communicate this information
properly to the generic madvise syscall implementation. The calling
convention is quite subtle there. madvise_vma() is supposed to either
return an error or update &prev otherwise the main loop will never
advance to the next vma and it will keep looping for ever without a way
to get out of the kernel.
It seems this has been broken since introduction. Nobody has noticed
because nobody seems to be using MADVISE_WILLNEED on these DAX mappings.
[mhocko@suse.com: rewrite changelog] Link: http://lkml.kernel.org/r/20171127115318.911-1-guoxuenan@huawei.com Fixes: fe77ba6f4f97 ("[PATCH] xip: madvice/fadvice: execute in place") Signed-off-by: chenjie <chenjie6@huawei.com> Signed-off-by: guoxuenan <guoxuenan@huawei.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Minchan Kim <minchan@kernel.org> Cc: zhangyi (F) <yi.zhang@huawei.com> Cc: Miao Xie <miaoxie@huawei.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Shaohua Li <shli@fb.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Carsten Otte <cotte@de.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Starting with this commit 35eb8b81edd4 ("x86/efi: Build our own page
table structures") efi regions have a separate page directory called
"efi_pgd". In order to access any efi region we have to first shift %cr3
to this page table. In the bgrt code we are trying to copy bgrt_header
and image, but these regions fall under "EFI_BOOT_SERVICES_DATA"
and to access these regions we have to shift %cr3 to efi_pgd and not
doing so will cause page fault as shown below.
As said above one way to fix this bug is to shift %cr3 to efi_pgd but we
are not doing that way because it leaks inner details of how we switch
to EFI page tables into a new call site and it also adds duplicate code.
Instead, we remove the call to efi_lookup_mapped_addr() and always
perform early_mem*() instead of early_io*() because we want to remap RAM
regions and not I/O regions. We also delete efi_lookup_mapped_addr()
because we are no longer using it.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Reported-by: Wendy Wang <wendy.wang@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Ravi Shankar <ravi.v.shankar@intel.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
With commit e1a58320a38d ("x86/mm: Warn on W^X mappings") all
users booting on 64-bit UEFI machines see the following warning,
------------[ cut here ]------------
WARNING: CPU: 7 PID: 1 at arch/x86/mm/dump_pagetables.c:225 note_page+0x5dc/0x780()
x86/mm: Found insecure W+X mapping at address ffff88000005f000/0xffff88000005f000
...
x86/mm: Checked W+X mappings: FAILED, 165660 W+X pages found.
...
This is caused by mapping EFI regions with RWX permissions.
There isn't much we can do to restrict the permissions for these
regions due to the way the firmware toolchains mix code and
data, but we can at least isolate these mappings so that they do
not appear in the regular kernel page tables.
In commit d2f7cbe7b26a ("x86/efi: Runtime services virtual
mapping") we started using 'trampoline_pgd' to map the EFI
regions because there was an existing identity mapping there
which we use during the SetVirtualAddressMap() call and for
broken firmware that accesses those addresses.
But 'trampoline_pgd' shares some PGD entries with
'swapper_pg_dir' and does not provide the isolation we require.
Notably the virtual address for __START_KERNEL_map and
MODULES_START are mapped by the same PGD entry so we need to be
more careful when copying changes over in
efi_sync_low_kernel_mappings().
This patch doesn't go the full mile, we still want to share some
PGD entries with 'swapper_pg_dir'. Having completely separate
page tables brings its own issues such as synchronising new
mappings after memory hotplug and module loading. Sharing also
keeps memory usage down.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Borislav Petkov <bp@suse.de> Acked-by: Borislav Petkov <bp@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1448658575-17029-6-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This change is a prerequisite for pending patches that switch to
a dedicated EFI page table, instead of using 'trampoline_pgd'
which shares PGD entries with 'swapper_pg_dir'. The pending
patches make it impossible to dereference the runtime service
function pointer without first switching %cr3.
It's true that we now have duplicated switching code in
efi_call_virt() and efi_call_phys_{prolog,epilog}() but we are
sacrificing code duplication for a little more clarity and the
ease of writing the page table switching code in C instead of
asm.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Borislav Petkov <bp@suse.de> Acked-by: Borislav Petkov <bp@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1448658575-17029-5-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The x86 pageattr code is confused about the data that is stored
in cpa->pfn, sometimes it's treated as a page frame number,
sometimes it's treated as an unshifted physical address, and in
one place it's treated as a pte.
The result of this is that the mapping functions do not map the
intended physical address.
This isn't a problem in practice because most of the addresses
we're mapping in the EFI code paths are already mapped in
'trampoline_pgd' and so the pageattr mapping functions don't
actually do anything in this case. But when we move to using a
separate page table for the EFI runtime this will be an issue.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Borislav Petkov <bp@suse.de> Acked-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1448658575-17029-3-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
An independent security researcher, Mohamed Ghannam, has reported
this vulnerability to Beyond Security's SecuriTeam Secure Disclosure
program.
The xfrm_dump_policy_done function expects xfrm_dump_policy to
have been called at least once or it will crash. This can be
triggered if a dump fails because the target socket's receive
buffer is full.
This patch fixes it by using the cb->start mechanism to ensure that
the initialisation is always done regardless of the buffer situation.
Fixes: 12a169e7d8f4 ("ipsec: Put dumpers on the dump list") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The start callback allows the caller to set up a context for the
dump callbacks. Presumably, the context can then be destroyed in
the done callback.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When accessing Xenstore in a transaction the user is specifying a
transaction id which he normally obtained from Xenstore when starting
the transaction. Xenstore is validating a transaction id against all
known transaction ids of the connection the request came in. As all
requests of a domain not being the one where Xenstore lives share
one connection, validation of transaction ids of different users of
Xenstore in that domain should be done by the kernel of that domain
being the multiplexer between the Xenstore users in that domain and
Xenstore.
In order to prohibit one Xenstore user "hijacking" a transaction from
another user the xenbus driver has to verify a given transaction id
against all known transaction ids of the user before forwarding it to
Xenstore.
s390 version of commit 334bb7738764 ("x86/kbuild: enable modversions
for symbols exported from asm") so we get also rid of all these
warnings:
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memcpy" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memmove" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memset" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "save_fpu_regs" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie64a" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie_exit" [vmlinux] version generation failed, symbol will not be versioned.
Protect against corrupt firmware files by ensuring that the length we
get for the data in a region actually lies within the available firmware
file data buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
On an error, snd_ctl_add already free's kctrl, so calling snd_ctl_free_one
to free it again leads to a double free error. Fix this by removing
the extraneous snd_ctl_free_one call.
Issue found using static analysis with CoverityScan, CID 1372908
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In function cm3232_reg_init(), it returns 0 even if the last call to
i2c_smbus_write_byte_data() returns a negative value (indicates error).
As a result, the return value may be inconsistent with the execution
status, and the caller of cm3232_reg_init() will not be able to detect
the error. This patch fixes the bug.
Previously, kernel sends NEW_PEER_CANDIDATE event to user land even if
the found peer does not have any room to accept other peer. This causes
continuous connection trials.
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Setting shutup when the action is HDA_FIXUP_ACT_PRE_PROBE might
not have the desired effect since it could be overridden by
another more generic shutup function. Prevent this by setting
the more specific shutup function on HDA_FIXUP_ACT_PROBE.
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
I reported the include issue for tracepoints a while ago, but nothing
seems to have happened. Now it bit us, since the drm_mm_print
conversion was broken for armada. Fix it, so I can re-enable armada
in the drm-misc build configs.
v2: Rebase just the compile fix on top of Chris' build fix.
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Reported-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de> Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de> Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
The first message to a remote node should prompt a new
connection even if it is RDMA operation. For RDMA operation
the MR mapping can fail because connections is not yet up.
Since the connection establishment is asynchronous,
we make sure the map failure because of unavailable
connection reach to the user by appropriate error code.
Before returning to the user, lets trigger the connection
so that its ready for the next retry.
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Because userspace gets Very Unhappy when calls like stat() and execve()
return -EINTR on 9p filesystem mounts. For instance, when bash is
looking in PATH for things to execute and some SIGCHLD interrupts
stat(), bash can throw a spurious 'command not found' since it doesn't
retry the stat().
In practice, hitting the problem is rare and needs a really
slow/bogged down 9p server.
Cc: stable@vger.kernel.org Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v3.17 and up Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Make sure to check that we actually have an Interface Association
Descriptor before dereferencing it during probe to avoid dereferencing a
NULL-pointer.
Let's allocate the the structure dynamically so we can get the firmware
loaded correctly:
[ 14.243057] as10x_usb: firmware: as102_data1_st.hex loaded with success
[ 14.500777] as10x_usb: firmware: as102_data2_st.hex loaded with success
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes: 129b69df9c90 ("powerpc: Use get_signal() signal_setup_done()") Cc: stable@vger.kernel.org # v3.17+ Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 3.13+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
A recent change fixing NFC device allocation itself introduced an
error-handling bug by returning an error pointer in case device-id
allocation failed. This is clearly broken as the callers still expected
NULL to be returned on errors as detected by Dan's static checker.
Fix this up by returning NULL in the event that we've run out of memory
when allocating a new device id.
Note that the offending commit is marked for stable (3.8) so this fix
needs to be backported along with it.
Fixes: 20777bc57c34 ("NFC: fix broken device allocation") Cc: stable <stable@vger.kernel.org> # 3.8 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce81f ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Fixes: 660e15519399 ("clk: ti: dra7-atl-clock: Fix of_node reference counting") Cc: stable <stable@vger.kernel.org> # 3.16: 660e15519399 Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
For many years some users of assigned devices have reported worse
performance on AMD processors with NPT than on AMD without NPT,
Intel or bare metal.
The reason turned out to be that SVM is discarding the guest PAT
setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-,
PA3=UC). The guest might be using a different setting, and
especially might want write combining but isn't getting it
(instead getting slow UC or UC- accesses).
Thanks a lot to geoff@hostfission.com for noticing the relation
to the g_pat setting. The patch has been tested also by a bunch
of people on VFIO users forums.
Fixes: 709ddebf81cb40e3c36c6109a7892e8b93a09464 Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409 Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Tested-by: Nick Sarnie <commendsarnex@gmail.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
This patch fixes a se_cmd->cmd_kref reference leak that can
occur when a non immediate TMR is proceeded our of command
sequence number order, and CMDSN_LOWER_THAN_EXP is returned
by iscsit_sequence_cmd().
To address this bug, call target_put_sess_cmd() during this
special case following what iscsit_process_scsi_cmd() does
upon CMDSN_LOWER_THAN_EXP.
Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Commit fd2421f54423 ("fs/9p: When doing inode lookup compare qid details
and inode mode bits.") transformed v9fs_qid_iget() to use iget5_locked()
instead of iget_locked(). However, the test() callback is not checking
fid.path at all, which means that a lookup in the inode cache can now
accidentally locate a completely wrong inode from the same inode hash
bucket if the other fields (qid.type and qid.version) match.
Fixes: fd2421f54423 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.") Cc: stable@vger.kernel.org Reviewed-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Some timer compat ioctls have NULL checks of timer instance with
snd_BUG_ON() that bring up WARN_ON() when the debug option is set.
Actually the condition can be met in the normal situation and it's
confusing and bad to spew kernel warnings with stack trace there.
Let's remove snd_BUG_ON() invocation and replace with the simple
checks. Also, correct the error code to EBADFD to follow the native
ioctl error handling.
The helper functions to parse and look for the clock source, selector
and multiplier unit may return the descriptor with a too short length
than required, while there is no sanity check in the caller side.
Add some sanity checks in the parsers, at least, to guarantee the
given descriptor size, for avoiding the potential crashes.
The usb-audio driver may trigger an out-of-bound access at parsing a
malformed selector unit, as it checks the header length only after
evaluating bNrInPins field, which can be already above the given
length. Fix it by adding the length check beforehand.
When the usb-audio descriptor contains the malformed feature unit
description with a too short length, the driver may access
out-of-bounds. Add a sanity check of the header size at the beginning
of parse_audio_feature_unit().
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0") Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
commit 3179f6200188 ("ALSA: core: add .get_time_info") had a side effect
of changing the behaviour of the PCM runtime tstamp. Prior to this
change tstamp was not updated by snd_pcm_update_hw_ptr0() unless the
hw_ptr had moved, after this change tstamp was always updated.
For an application using alsa-lib, doing snd_pcm_readi() followed by
snd_pcm_status() to estimate the age of the read samples by subtracting
status->avail * [sample rate] from status->tstamp this change degraded
the accuracy of the estimate on devices where the pcm hw does not
provide a granular hw_ptr, e.g., devices using
soc-generic-dmaengine-pcm.c and a dma-engine with residue_granularity
DMA_RESIDUE_GRANULARITY_DESCRIPTOR. The accuracy of the estimate
depended on the latency between the PCM hw completing a period and the
driver called snd_pcm_period_elapsed() to notify ALSA core, typically
determined by interrupt handling latency. After the change the accuracy
of the estimate depended on the latency between the PCM hw completing a
period and the application calling snd_pcm_status(), determined by the
scheduling of the application process. The maximum error of the
estimate is one period length in both cases, but the error average and
variance is smaller when it depends on interrupt latency.
Instead of always updating tstamp, update it only if audio_tstamp
changed.
If there are pending writes subject to delayed allocation, then i_size
will show size after the writes have completed, while i_disksize
contains the value of i_size on the disk (since the writes have not
been persisted to disk).
If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either
with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size
after the fallocate(2) is between i_size and i_disksize, then after a
crash, if a journal commit has resulted in the changes made by the
fallocate() call to be persisted after a crash, but the delayed
allocation write has not resolved itself, i_size would not be updated,
and this would cause the following e2fsck complaint:
Inode 12, end of extent exceeds allowed value
(logical block 33, physical block 33441, len 7)
This can only take place on a sparse file, where the fallocate(2) call
is allocating blocks in a range which is before a pending delayed
allocation write which is extending i_size. Since this situation is
quite rare, and the window in which the crash must take place is
typically < 30 seconds, in practice this condition will rarely happen.
Nevertheless, it can be triggered in testing, and in particular by
xfstests generic/456.
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
If a delegation has been revoked by the server, operations using that
delegation should error out with NFS4ERR_DELEG_REVOKED in the >4.1
case, and NFS4ERR_BAD_STATEID otherwise.
The server needs NFSv4.1 clients to explicitly free revoked delegations.
If the server returns NFS4ERR_DELEG_REVOKED, the client will do that;
otherwise it may just forget about the delegation and be unable to
recover when it later sees SEQ4_STATUS_RECALLABLE_STATE_REVOKED set on a
SEQUENCE reply. That can cause the Linux 4.1 client to loop in its
stage manager.
Signed-off-by: Andrew Elble <aweits@rit.edu> Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
nfs4_get_referral is wiping out any cached attributes with what was
returned via GETATTR(fs_locations), but the bit mask for that
operation does not request any file attributes.
Retrieve owner and timestamp information so that the memcpy in
nfs4_get_referral fills in more attributes.
Changes since v1:
- Don't request attributes that the client unconditionally replaces
- Request only MOUNTED_ON_FILEID or FILEID attribute, not both
- encode_fs_locations() doesn't use the third bitmask word
Fixes: 6b97fd3da1ea ("NFSv4: Follow a referral") Suggested-by: Pradeep Thomas <pradeepthomas@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
isofs uses a 'char' variable to load the number of years since
1900 for an inode timestamp. On architectures that use a signed
char type by default, this results in an invalid date for
anything beyond 2027.
This changes the function argument to a 'u8' array, which
is defined the same way on all architectures, and unambiguously
lets us use years until 2155.
This should be backported to all kernels that might still be
in use by that date.
Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In bcache code, sysfs entries are created before all resources get
allocated, e.g. allocation thread of a cache set.
There is posibility for NULL pointer deference if a resource is accessed
but which is not initialized yet. Indeed Jorg Bornschein catches one on
cache set allocation thread and gets a kernel oops.
The reason for this bug is, when bch_bucket_alloc() is called during
cache set registration and attaching, ca->alloc_thread is not properly
allocated and initialized yet, call wake_up_process() on ca->alloc_thread
triggers NULL pointer deference failure. A simple and fast fix is, before
waking up ca->alloc_thread, checking whether it is allocated, and only
wake up ca->alloc_thread when it is not NULL.
Signed-off-by: Coly Li <colyli@suse.de> Reported-by: Jorg Bornschein <jb@capsec.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: stable@vger.kernel.org Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
There is a race condition between nilfs_dirty_inode() and
nilfs_set_file_dirty().
When a file is opened, nilfs_dirty_inode() is called to update the
access timestamp in the inode. It calls __nilfs_mark_inode_dirty() in a
separate transaction. __nilfs_mark_inode_dirty() caches the ifile
buffer_head in the i_bh field of the inode info structure and marks it
as dirty.
After some data was written to the file in another transaction, the
function nilfs_set_file_dirty() is called, which adds the inode to the
ns_dirty_files list.
Then the segment construction calls nilfs_segctor_collect_dirty_files(),
which goes through the ns_dirty_files list and checks the i_bh field.
If there is a cached buffer_head in i_bh it is not marked as dirty
again.
Since nilfs_dirty_inode() and nilfs_set_file_dirty() use separate
transactions, it is possible that a segment construction that writes out
the ifile occurs in-between the two. If this happens the inode is not
on the ns_dirty_files list, but its ifile block is still marked as dirty
and written out.
In the next segment construction, the data for the file is written out
and nilfs_bmap_propagate() updates the b-tree. Eventually the bmap root
is written into the i_bh block, which is not dirty, because it was
written out in another segment construction.
As a result the bmap update can be lost, which leads to file system
corruption. Either the virtual block address points to an unallocated
DAT block, or the DAT entry will be reused for something different.
The error can remain undetected for a long time. A typical error
message would be one of the "bad btree" errors or a warning that a DAT
entry could not be found.
This bug can be reproduced reliably by a simple benchmark that creates
and overwrites millions of 4k files.
Currently if the autofs kernel module gets an error when writing to the
pipe which links to the daemon, then it marks the whole moutpoint as
catatonic, and it will stop working.
It is possible that the error is transient. This can happen if the
daemon is slow and more than 16 requests queue up. If a subsequent
process tries to queue a request, and is then signalled, the write to
the pipe will return -ERESTARTSYS and autofs will take that as total
failure.
So change the code to assess -ERESTARTSYS and -ENOMEM as transient
failures which only abort the current request, not the whole mountpoint.
It isn't a crash or a data corruption, but having autofs mountpoints
suddenly stop working is rather inconvenient.
Ian said:
: And given the problems with a half dozen (or so) user space applications
: consuming large amounts of CPU under heavy mount and umount activity this
: could happen more easily than we expect.
Link: http://lkml.kernel.org/r/87y3norvgp.fsf@notabene.neil.brown.name Signed-off-by: NeilBrown <neilb@suse.com> Acked-by: Ian Kent <raven@themaw.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Fix a commit 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
regression, then activated by commit 6a9c001b7ec3 ("MIPS: Switch ELF
core dumper to use regsets.)", that caused n32 processes to dump o32
core files by failing to set the EF_MIPS_ABI2 flag in the ELF core file
header's `e_flags' member:
statement placed in arch/mips/kernel/binfmt_elfn32.c, however in the
regset case, i.e. when CORE_DUMP_USE_REGSET is set, ELF_CORE_EFLAGS is
no longer used by `fill_note_info' in fs/binfmt_elf.c, and instead the
`->e_flags' member of the regset view chosen is. We have the views
defined in arch/mips/kernel/ptrace.c, however only an o32 and an n64
one, and the latter is used for n32 as well. Consequently an o32 core
file is incorrectly dumped from n32 processes (the ELF32 vs ELF64 class
is chosen elsewhere, and the 32-bit one is correctly selected for n32).
Correct the issue then by defining an n32 regset view and using it as
appropriate. Issue discovered in GDB testing.
The bug can be easily triggered, if an extra delay (e.g. 10ms) is added
between the test of DMF_FREEING & DMF_DELETING and dm_get() in
dm_get_from_kobject().
To fix it, we need to ensure the test of DMF_FREEING & DMF_DELETING and
dm_get() are done in an atomic way, so _minor_lock is used.
The other callers of dm_get() have also been checked to be OK: some
callers invoke dm_get() under _minor_lock, some callers invoke it under
_hash_lock, and dm_start_request() invoke it after increasing
md->open_count.
Cc: stable@vger.kernel.org Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The default max_cache_size_bytes for dm-bufio is meant to be the lesser
of 25% of the size of the vmalloc area and 2% of the size of lowmem.
However, on 32-bit systems the intermediate result in the expression
overflows, causing the wrong result to be computed. For example, on a
32-bit system where the vmalloc area is 520093696 bytes, the result is 1174405 rather than the expected 130023424, which makes the maximum
cache size much too small (far less than 2% of lowmem). This causes
severe performance problems for dm-verity users on affected systems.
Fix this by using mult_frac() to correctly multiply by a percentage. Do
this for all places in dm-bufio that multiply by a percentage. Also
replace (VMALLOC_END - VMALLOC_START) with VMALLOC_TOTAL, which contrary
to the comment is now defined in include/linux/vmalloc.h.
Depends-on: 9993bc635 ("sched/x86: Fix overflow in cyc2ns_offset") Fixes: 95d402f057f2 ("dm: add bufio") Cc: <stable@vger.kernel.org> # v3.2+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.
In a kernel with the AP2 bug, the dump looks like this:
Fixes: ded947798469 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE") Signed-off-by: Philip Derrin <philip@cog.systems> Tested-by: Neil Dick <neil@cog.systems> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).
For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.
The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.
Fixes: 1e3479225acb ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error") Signed-off-by: Philip Derrin <philip@cog.systems> Reported-by: Neil Dick <neil@cog.systems> Tested-by: Neil Dick <neil@cog.systems> Tested-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c
Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked 1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
The current implementation of synchronize_sched_expedited() incorrectly
assumes that resched_cpu() is unconditional, which it is not. This means
that synchronize_sched_expedited() can hang when resched_cpu()'s trylock
fails as follows (analysis by Neeraj Upadhyay):
o CPU1 is waiting for expedited wait to complete:
sync_rcu_exp_select_cpus
rdp->exp_dynticks_snap & 0x1 // returns 1 for CPU5
IPI sent to CPU5
synchronize_sched_expedited_wait
ret = swait_event_timeout(rsp->expedited_wq,
sync_rcu_preempt_exp_done(rnp_root),
jiffies_stall);
expmask = 0x20, CPU 5 in idle path (in cpuidle_enter())
o CPU5 handles IPI and fails to acquire rq lock.
Handles IPI
sync_sched_exp_handler
resched_cpu
returns while failing to try lock acquire rq->lock
need_resched is not set
o CPU5 calls rcu_idle_enter() and as need_resched is not set, goes to
idle (schedule() is not called).
o CPU 1 reports RCU stall.
Given that resched_cpu() is now used only by RCU, this commit fixes the
assumption by making resched_cpu() unconditional.
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org> Suggested-by: Neeraj Upadhyay <neeraju@codeaurora.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Just switch to the new wait API like we did for commit d9dc8b0f8b4e ("net: fix sleeping for sk_wait_event()").
Reported-by: Michal Kubecek <mkubecek@suse.cz> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Jorgen Hansen <jhansen@vmware.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
When a thread is prepared for waiting by calling prepare_to_wait, sleeping
is not allowed until either the wait has taken place or finish_wait has
been called. The existing code in af_vsock imposed unnecessary no-sleep
assumptions to a broad list of backend functions.
This patch shrinks the influence of prepare_to_wait to the area where it
is strictly needed, therefore relaxing the no-sleep restriction there.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
In commit 242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes: 242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf") Reported-by: jeffy <jeffy.chen@rock-chips.com> Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Current buffer size of 64 is too small. objdump shows that there are
instructions which would require up to 75 bytes buffer (with current
formating). 128 bytes "ought to be enough for anybody".
Also replaces 8 spaces with a single tab to reduce the memory footprint.
Fixes the following KASAN finding:
BUG: KASAN: stack-out-of-bounds in number+0x3fe/0x538
Write of size 1 at addr 000000005a4a75a0 by task bash/1282
The e7 opcode table does not have an end marker. Hence when trying to
find an unknown e7 instruction the code will access memory behind the
table until it finds something that matches the opcode, or the kernel
crashes, whatever comes first.
This affects not only the in-kernel disassembler but also uprobes and
kprobes which refuse to set a probe on unknown instructions, and
therefore search the opcode tables to figure out if instructions are
known or not.
For PREEMPT enabled kernels the runtime instrumentation (RI) code
contains a possible use-after-free bug. If a task that makes use of RI
exits, it will execute do_exit() while still enabled for preemption.
That function will call exit_thread_runtime_instr() via
exit_thread(). If exit_thread_runtime_instr() gets preempted after the
RI control block of the task has been freed but before the pointer to
it is set to NULL, then save_ri_cb(), called from switch_to(), will
write to already freed memory.
Avoid this and simply disable preemption while freeing the control
block and setting the pointer to NULL.
Fixes: e4b8b3f33fca ("s390: add support for runtime instrumentation") Cc: <stable@vger.kernel.org> # v3.7+ Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
projects / linux-stable / log