If using a kernel with CONFIG_XFS_RT=y and we set the RHINHERIT flag on
a directory in a filesystem that does not have a realtime device and
create a new file in that directory, it gets marked as a real time file.
When data is written and a fsync is issued, the filesystem attempts to
flush a non-existent rt device during the fsync process.
This results in a crash dereferencing a null buftarg pointer in
xfs_blkdev_issue_flush():
Setting RT inode flags does not require special privileges so any
unprivileged user can cause this oops to occur. To reproduce, confirm
kernel is compiled with CONFIG_XFS_RT=y and run:
There are a number of callers of nfs_pageio_complete() that want to
continue using the nfs_pageio_descriptor without needing to call
nfs_pageio_init() again. Examples include nfs_pageio_resend() and
nfs_pageio_cond_complete().
The problem is that nfs_pageio_complete() also calls
nfs_pageio_cleanup_mirroring(), which frees up the array of mirrors.
This can lead to writeback errors, in the next call to
nfs_pageio_setup_mirroring().
Fix by simply moving the allocation of the mirrors to
nfs_pageio_setup_mirroring().
Since commit 18290650b1c8 ("NFS: Move buffered I/O locking into
nfs_file_write()") nfs_file_write() has not flushed the correct byte
range during synchronous writes. generic_write_sync() expects that
iocb->ki_pos points to the right edge of the range rather than the
left edge.
To replicate the problem, open a file with O_DSYNC, have the client
write at increasing offsets, and then print the successful offsets.
Block port 2049 partway through that sequence, and observe that the
client application indicates successful writes in advance of what the
server received.
When there's a fatal signal pending, arm's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9e4 ("arm64: dts: add the Marvell Armada 3700 family and a development board") Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 41977e86c984 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c984 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829 Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu> Cc: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 147277540bbc ("kvm: svm: Add support for additional SVM NPF error
codes", 2016-11-23) added a new error code to aid nested page fault
handling. The commit unprotects (kvm_mmu_unprotect_page) the page when
we get a NPF due to guest page table walk where the page was marked RO.
However, if an L0->L2 shadow nested page table can also be marked read-only
when a page is read only in L1's nested page table. If such a page
is accessed by L2 while walking page tables it can cause a nested
page fault (page table walks are write accesses). However, after
kvm_mmu_unprotect_page we may get another page fault, and again in an
endless stream.
To cover this use case, we qualify the new error_code check with
vcpu->arch.mmu_direct_map so that the error_code check would run on L1
guest, and not the L2 guest. This avoids hitting the above scenario.
Fixes: 147277540bbc54119172481c8ef6d930cc9fbfc2 Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Lendacky <thomas.lendacky@amd.com> Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen while reading the code, in handle_mm_fault(), in the case
arch_vma_access_permitted() is failing the call to
mem_cgroup_oom_disable() is not made.
To fix that, move the call to mem_cgroup_oom_enable() after calling
arch_vma_access_permitted() as it should not have entered the memcg OOM.
If initializing a small swap file fails because the swap file has a
problem (holes, etc.) then we need to free the cluster info as part of
cleanup. Unfortunately a previous patch changed the code to use kvzalloc
but did not change all the vfree calls to use kvfree.
Found by running generic/357 from xfstests.
Link: http://lkml.kernel.org/r/20170831233515.GR3775@magnolia Fixes: 54f180d3c181 ("mm, swap: use kvzalloc to allocate some swap data structures") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: "Huang, Ying" <ying.huang@intel.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__radix_tree_preload() only disables preemption if no error is returned.
So we really need to make sure callers always check the return value.
idr_preload() contract is to always disable preemption, so we need
to add a missing preempt_disable() if an error happened.
Similarly, ida_pre_get() only needs to call preempt_enable() in the
case no error happened.
Link: http://lkml.kernel.org/r/1504637190.15310.62.camel@edumazet-glaptop3.roam.corp.google.com Fixes: 0a835c4f090a ("Reimplement IDR and IDA using the radix tree") Fixes: 7ad3d4d85c7a ("ida: Move ida_bitmap to a percpu variable") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit bcd37f4a0831 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a0831 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several distributions mount the "proper root" as ro during initrd and
then remount it as rw before pivot_root(2). Thus, if a rescan had been
aborted by a previous shutdown, the rescan would never be resumed.
This issue would manifest itself as several btrfs ioctl(2)s causing the
entire machine to hang when btrfs_qgroup_wait_for_completion was hit
(due to the fs_info->qgroup_rescan_running flag being set but the rescan
itself not being resumed). Notably, Docker's btrfs storage driver makes
regular use of BTRFS_QUOTA_CTL_DISABLE and BTRFS_IOC_QUOTA_RESCAN_WAIT
(causing this problem to be manifested on boot for some machines).
Cc: Jeff Mahoney <jeffm@suse.com> Fixes: b382a324b60f ("Btrfs: fix qgroup rescan resume on mount") Signed-off-by: Aleksa Sarai <asarai@suse.de> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default host NQN, which is generated based on the host's UUID,
does not follow the UUID-based NQN format laid out in the NVMe 1.3
specification. Remove the "NVMf:" portion of the NQN to match the spec.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Fixes: 78f3482d7480 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c51d0ac59f24 ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Fixes: c51d0ac59f24 ("mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c") Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f70e4df2b384 ("rtlwifi: Add code to read new versions of
firmware") added code to load an old firmware file if the new one is
not available. Unfortunately that code is never reached because
request_firmware_nowait() does not wait for the firmware to show up
and returns 0 even if the file is not there.
Use the existing fallback mechanism introduced by commit 62009b7f1279
("rtlwifi: rtl8192cu: Add new firmware") instead.
Fixes: f70e4df2b384 ("rtlwifi: Add code to read new versions of firmware") Signed-off-by: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of_device_get_modalias() returns the number of bytes that would have
been written to the target string, regardless of how much did fit in the
buffer, it's possible that the returned index points beyond the buffer
passed to of_device_modalias() - causing memory beyond the buffer to be
null terminated.
Fixes: 0634c2958927 ("of: Add function for generating a DT modalias with a newline") Cc: Rob Herring <robh@kernel.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1bc0eb044615 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Commit 0a94efb5acbb ("workqueue: implicit ordered attribute should be
overridable") introduced a __WQ_ORDERED_EXPLICIT flag but gave it the
same value as __WQ_LEGACY. I don't believe these were intended to
mean the same thing, so renumber __WQ_ORDERED_EXPLICIT.
Fixes: 0a94efb5acbb ("workqueue: implicit ordered attribute should be ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it more clear that post commit return ret is really return 0,
and add a missing drm_atomic_helper_cleanup_planes when
drm_atomic_helper_wait_for_fences fails.
Fixes: 839ca903f12e ("drm/nouveau/kms/nv50: transition to atomic interfaces internally") Cc: Ben Skeggs <bskeggs@redhat.com> Cc: dri-devel@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-2-maarten.lankhorst@linux.intel.com Reviewed-by: Sean Paul <seanpaul@chromium.org>
[mlankhorst: Use if (ret) to remove the goto in success case.] Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that MSI does not work on either G5 PPC nor on a E5500-based
platform, where other hardware is reported to work fine with MSI.
Both tests were conducted with NV4x hardware, so perhaps other (or even
this) hardware can be made to work. It's still possible to force-enable
with config=NvMSI=1 on load.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now there is a potential hang situation for postcopy migrations,
if the guest is enabling storage keys on the target system during the
postcopy process.
For storage key virtualization, we have to forbid the empty zero page as
the storage key is a property of the physical page frame. As we enable
storage key handling lazily we then drop all mappings for empty zero
pages for lazy refaulting later on.
This does not work with the postcopy migration, which relies on the
empty zero page never triggering a fault again in the future. The reason
is that postcopy migration will simply read a page on the target system
if that page is a known zero page to fault in an empty zero page. At
the same time postcopy remembers that this page was already transferred
- so any future userfault on that page will NOT be retransmitted again
to avoid races.
If now the guest enters the storage key mode while in postcopy, we will
break this assumption of postcopy.
The solution is to disable the empty zero page for KVM guests early on
and not during storage key enablement. With this change, the postcopy
migration process is guaranteed to start after no zero pages are left.
As guest pages are very likely not empty zero pages anyway the memory
overhead is also pretty small.
While at it this also adds proper page table locking to the zero page
removal.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the resources and DMI ID's for the MEN SC31,
which uses a different address region to map the LPC bus than
the one used for the existing SC24.
Signed-off-by: Michael Moese <michael.moese@men.de>
[jth add stable tag] Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mwifiex records information about various channels as it receives scan
information. It does this by appending to a buffer that was sized
to the max number of supported channels on any band, but there are
numerous problems:
(a) scans can return info from more than one band (e.g., both 2.4 and 5
GHz), so the determined "max" is not large enough
(b) some firmware appears to return multiple results for a given
channel, so the max *really* isn't large enough
(c) there is no bounds checking when stashing these stats, so problems
(a) and (b) can easily lead to buffer overflows
Let's patch this by setting a slightly-more-correct max (that accounts
for a combination of both 2.4G and 5G bands) and adding a bounds check
when writing to our statistics buffer.
Due to problem (b), we still might not properly report all known survey
information (e.g., with "iw <dev> survey dump"), since duplicate results
(or otherwise "larger than expected" results) will cause some
truncation. But that's a problem for a future bugfix.
(And because of this known deficiency, only log the excess at the WARN
level, since that isn't visible by default in this driver and would
otherwise be a bit too noisy.)
Fixes: bf35443314ac ("mwifiex: channel statistics support for mwifiex") Cc: Avinash Patil <patila@marvell.com> Cc: Xinming Hu <huxm@marvell.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Can be reproduced when running dlm_controld (tested on 4.4.x, 4.12.4):
# seq 1 100 | xargs -P0 -n1 dlm_tool join
# seq 1 100 | xargs -P0 -n1 dlm_tool leave
misc_register fails due to duplicate sysfs entry, which causes
dlm_device_register to free ls->ls_device.name.
In dlm_device_deregister the name was freed again, causing memory
corruption.
According to the comment in dlm_device_deregister the name should've been
set to NULL when registration fails,
so this patch does that.
Trackpoint buttons detection fails on ThinkPad 570 and 470 series,
this makes the middle button of the trackpoint to not being recogized.
As I don't believe there is any trackpoint with less than 3 buttons this
patch just assumes three buttons when the extended button information
read fails.
Signed-off-by: Oscar Campos <oscar.campos@member.fsf.org> Acked-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global spinlock `l3_remap_lock` is reinitialized every time the
"probe" function `alt_fpga_bridge_probe()` is called. It should only be
initialized once. Use `DEFINE_SPINLOCK()` to initialize it statically.
Fixes: e5f8efa5c8bf ("ARM: socfpga: fpga bridge driver support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-By: Moritz Fischer <mdf@kernel.org> Signed-off-by: Alan Tull <atull@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):
drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_done':
drivers/crypto/caam/caamalg_qi.c:794:2: error: implicit declaration of function 'dbg_dump_sg' [-Werror=implicit-function-declaration]
dbg_dump_sg(KERN_ERR, "dst @" __stringify(__LINE__)": ",
Since dbg_dump_sg() is shared between caam/jr and caam/qi, move it
in a shared location and export it.
At the same time:
-reduce ifdeferry by providing a no-op implementation for !DEBUG case
-rename it to caam_dump_sg() to be consistent in terms of
exported symbols namespace (caam_*)
On binder_init() the devices string is duplicated and smashed into individual
device names which are passed along. However, the original duplicated string
wasn't freed in case binder_init() failed. Let's free it on error.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.
Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0. Fix this by shifting only by 4 bits to correctly get the upper nybble.
Detected by CoverityScan, CID#142891 ("Operands don't affect result")
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
binder_fd_array_object starts with a 4-byte header,
followed by a few fields that are 8 bytes when
ANDROID_BINDER_IPC_32BIT=N.
This can cause alignment issues in a 64-bit kernel
with a 32-bit userspace, as on x86_32 an 8-byte primitive
may be aligned to a 4-byte address. Pad with a __u32
to fix this.
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend") Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume") Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe") Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Daniel Mack <zonque@gmail.com> Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
The race was introduced by me in commit 971316f0503a ("epoll:
ep_unregister_pollwait() can use the freed pwq->whead"). I did not
realize that nothing can protect eventpoll after ep_poll_callback() sets
->whead = NULL, only whead->lock can save us from the race with
ep_free() or ep_remove().
Move ->whead = NULL to the end of ep_poll_callback() and add the
necessary barriers.
TODO: cleanup the ewake/EPOLLEXCLUSIVE logic, it was confusing even
before this patch.
Hopefully this explains use-after-free reported by syzcaller:
BUG: KASAN: use-after-free in debug_spin_lock_before
...
_raw_spin_lock_irqsave+0x4a/0x60 kernel/locking/spinlock.c:159
ep_poll_callback+0x29f/0xff0 fs/eventpoll.c:1148
this is spin_lock(eventpoll->lock),
...
Freed by task 17774:
...
kfree+0xe8/0x2c0 mm/slub.c:3883
ep_free+0x22c/0x2a0 fs/eventpoll.c:865
Fixes: 971316f0503a ("epoll: ep_unregister_pollwait() can use the freed pwq->whead") Reported-by: 范龙飞 <long7573@126.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since switching the I2C-over-AUX helpers, there have been regressions on
some display combinations due to us not having support for "address only"
transactions.
This commits enables support for them for GF119 and newer.
Earlier GPUs have been reverted to a custom I2C-over-AUX algorithm.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMe 1.3 specification defines the Optional Admin Command Support feature
flags, bit 8 set to '1' then the controller supports the Doorbell Buffer
Config command. Bit 7 is used for Virtualization Mangement command.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: f9f38e33 ("nvme: improve performance for virtual NVMe devices") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fail to get needed page for pool, need to put allocated pages
into pool. But current code has a miscalculation of allocated pages,
correct it.
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Monk Liu <monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'dir' parameter in xfrm_migrate() is a user-controlled byte which is used
as an array index. This can lead to an out-of-bound access, kernel lockup and
DoS. Add a check for the 'dir' value.
Using sg_miter_start and sg_miter_next, the buffer of an SG is kmap'ed
to *buff. The current code calls sg_miter_stop (and thus kunmap) on the
SG entry before the last access of *buff.
The patch moves the sg_miter_stop call after the last access to *buff to
ensure that the memory pointed to by *buff is still mapped.
Fixes: 4816c9406430 ("lib/mpi: Fix SG miter leak") Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
[ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
[ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
.owner_cpu: 0
[ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W 4.12.0-03002-gec979a4-dirty #40
[ 5668.772796] Hardware name: Nokia RX-51 board
[ 5668.773071] Workqueue: phy1 wl1251_irq_work
[ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
(show_stack+0x10/0x14)
[ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
(do_raw_spin_lock+0x6c/0xa0)
[ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
(_raw_spin_lock_irqsave+0x10/0x18)
[ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
(wl1251_op_tx+0x38/0x5c)
[ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
(ieee80211_tx_frags+0x188/0x1c0)
[ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
(__ieee80211_tx+0x6c/0x130)
[ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
(ieee80211_tx+0xdc/0x104)
[ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
(__ieee80211_subif_start_xmit+0x454/0x8c8)
[ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
[<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
[ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
[<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...
by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmwgfx currently cannot support non-blocking commit because when
vmw_*_crtc_page_flip is called, drm_atomic_nonblocking_commit()
schedules the update on a thread. This means vmw_*_crtc_page_flip
cannot rely on the new surface being bound before the subsequent
dirty and flush operations happen.
Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Charmaine Lee <charmainel@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the block layer in single queue mode, get_request()
returns ERR_PTR(-EAGAIN) if the queue is dying and the REQ_NOWAIT
flag has been passed to get_request(). Avoid that the kernel
reports soft lockup complaints in this case due to continuous
requeuing activity.
Fixes: 7083abbbf ("dm mpath: avoid that path removal can trigger an infinite loop") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Tested-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent patch had an endian warning ie
cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup()
Signed-off-by: Steve French <smfrench@gmail.com> CC: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the maximum size of SMB2/3 header is set incorrectly which
leads to hanging of directory listing operations on encrypted SMB3
connections. Fix this by setting the maximum size to 170 bytes that
is calculated as RFC1002 length field size (4) + transform header
size (52) + SMB2 header size (64) + create response size (56).
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Acked-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tests/attr.c: In function 'store_event':
tests/attr.c:66:27: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__u64 {aka long unsigned int}' [-Werror=format=]
snprintf(path, PATH_MAX, "%s/event-%d-%llu-%d", dir,
^
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory_pressure control file was incorrectly set up without
a private value (0, by default). As a result, this control
file was treated like memory_migrate on read. By adding back the
FILE_MEMORY_PRESSURE private value, the correct memory pressure value
will be returned.
Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 7dbdb199d3bf ("cgroup: replace cftype->mode with CFTYPE_WORLD_WRITABLE") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When !NUMA, cpumask_of_node(@node) equals cpu_online_mask regardless of
@node. The assumption seems that if !NUMA, there shouldn't be more than
one node and thus reporting cpu_online_mask regardless of @node is
correct. However, that assumption was broken years ago to support
DISCONTIGMEM and whether a system has multiple nodes or not is
separately controlled by NEED_MULTIPLE_NODES.
This means that, on a system with !NUMA && NEED_MULTIPLE_NODES,
cpumask_of_node() will report cpu_online_mask for all possible nodes,
indicating that the CPUs are associated with multiple nodes which is an
impossible configuration.
This bug has been around forever but doesn't look like it has caused any
noticeable symptoms. However, it triggers a WARN recently added to
workqueue to verify NUMA affinity configuration.
Fix it by reporting empty cpumask on non-zero nodes if !NUMA.
ceph_readpage() unlocks page prematurely prematurely in the case
that page is reading from fscache. Caller of readpage expects that
page is uptodate when it get unlocked. So page shoule get locked
by completion callback of fscache_read_or_alloc_pages()
Wendy Wang reported off-list that a RAS HWPOISON-SOFT test case failed
and bisected it to the commit 479f854a207c ("mm, page_alloc: defer
debugging checks of pages allocated from the PCP").
The problem is that a page that was poisoned with madvise() is reused.
The commit removed a check that would trigger if DEBUG_VM was enabled
but re-enabling the check only fixes the problem as a side-effect by
printing a bad_page warning and recovering.
The root of the problem is that an madvise() can leave a poisoned page
on the per-cpu list. This patch drains all per-cpu lists after pages
are poisoned so that they will not be reused. Wendy reports that the
test case in question passes with this patch applied. While this could
be done in a targeted fashion, it is over-complicated for such a rare
operation.
Commit 7c051267931a ("mm, fork: make dup_mmap wait for mmap_sem for
write killable") made it possible to kill a forking task while it is
waiting to acquire its ->mmap_sem for write, in dup_mmap().
However, it was overlooked that this introduced an new error path before
the new mm_struct's ->uprobes_state.xol_area has been set to NULL after
being copied from the old mm_struct by the memcpy in dup_mm(). For a
task that has previously hit a uprobe tracepoint, this resulted in the
'struct xol_area' being freed multiple times if the task was killed at
just the right time while forking.
Fix it by setting ->uprobes_state.xol_area to NULL in mm_init() rather
than in uprobe_dup_mmap().
With CONFIG_UPROBE_EVENTS=y, the bug can be reproduced by the same C
program given by commit 2b7e8665b4ff ("fork: fix incorrect fput of
->exe_file causing use-after-free"), provided that a uprobe tracepoint
has been set on the fork_thread() function. For example:
For asynchronous operation, SGs are allocated without a page mapped to
them or with a page that is not used (ref-counted). If the SGL is freed,
the code must only call put_page for an SG if there was a page assigned
and ref-counted in the first place.
This fixes a kernel crash when using io_submit with more than one iocb
using the sendmsg and sendpage (vmsplice/splice) interface.
Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9ae433bc79f9 ("crypto: chacha20 - convert generic and x86 versions
to skcipher") ported the existing chacha20 code to use the new skcipher
API, and introduced a bug along the way. Unfortunately, the tcrypt tests
did not catch the error, and it was only found recently by Tobias.
Stefan kindly diagnosed the error, and proposed a fix which is similar
to the one below, with the exception that 'walk.stride' is used rather
than the hardcoded block size. This does not actually matter in this
case, but it's a better example of how to use the skcipher walk API.
Fixes: 9ae433bc79f9 ("crypto: chacha20 - convert generic and x86 ...") Cc: Steffen Klassert <steffen.klassert@secunet.com> Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.
When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.
Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.
User-modified input settings no longer survive a suspend/resume cycle.
Starting with 4.12, the touchpad is reinitialized on every reconnect
because the hardware appears to be different. This can be reproduced
by running the following as root:
[30378.295794] psmouse serio1: synaptics: hardware appears to be
different: id(149271-149271), model(114865-114865),
caps(d047b3-d047b1), ext(b40000-b40000).
Note the single bit difference in caps: bit 1 (SYN_CAP_MULTIFINGER).
This happens because we modify our stored copy of the device info
capabilities when we enable advanced gesture mode but this change is
not reflected in the actual hardware capabilities.
It worked in the past because synaptics_query_hardware used to modify
the stored synaptics_device_info struct instead of filling in a new
one, as it does now.
Fix it by no longer faking the SYN_CAP_MULTIFINGER bit when setting
advanced gesture mode. This necessitated a small refactoring.
Fixes: 6c53694fb222 ("Input: synaptics - split device info into a separate structure") Signed-off-by: Anthony Martin <ality@pbrane.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support") Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The x86 version of insb/insw/insl uses an inline assembly that does
not have the target buffer listed as an output. This can confuse
the compiler, leading it to think that a subsequent access of the
buffer is uninitialized:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_mgmt_scan_confirm’:
drivers/net/wireless/wl3501_cs.c:665:9: error: ‘sig.status’ is used uninitialized in this function [-Werror=uninitialized]
drivers/net/wireless/wl3501_cs.c:668:12: error: ‘sig.cap_info’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c: In function 'sb1000_rx':
drivers/net/sb1000.c:775:9: error: 'st[0]' is used uninitialized in this function [-Werror=uninitialized]
drivers/net/sb1000.c:776:10: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c:784:11: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I tried to mark the exact input buffer as an output here, but couldn't
figure it out. As suggested by Linus, marking all memory as clobbered
however is good enough too. For the outs operations, I also add the
memory clobber, to force the input to be written to local variables.
This is probably already guaranteed by the "asm volatile", but it can't
hurt to do this for symmetry.
When there's a fatal signal pending, arm64's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Laura Abbott <labbott@redhat.com> Reviewed-by: Steve Capper <steve.capper@arm.com> Tested-by: Steve Capper <steve.capper@arm.com> Reviewed-by: James Morse <james.morse@arm.com> Tested-by: James Morse <james.morse@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no guarantee that the various isync's involved with
the context switch will order the update of the CPU mask with
the first TLB entry for the new context being loaded by the HW.
Be safe here and add a memory barrier to order any subsequent
load/store which may bring entries into the TLB.
The corresponding barrier on the other side already exists as
pte updates use pte_xchg() which uses __cmpxchg_u64 which has
a sync after the atomic operation.
Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add comments in the code]
[mpe: Backport to 4.12, minor context change] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle
EC events) introduced acpi_ec_ecdt_start(), but that function is
invoked before acpi_ec_query_init(), which is too early. This causes
the kernel to crash if an EC event occurs after boot, when ec_query_wq
is not valid:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
...
Workqueue: events acpi_ec_event_handler
task: ffff9f539790dac0 task.stack: ffffb437c0e10000
RIP: 0010:__queue_work+0x32/0x430
Normally, the DSDT EC should always be valid, so acpi_ec_ecdt_start()
is actually a no-op in the majority of cases. However, commit c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe)
caused the probing of the DSDT EC as the "boot EC" to be skipped when
the ECDT EC is valid and uncovered the bug.
Fix this issue by invoking acpi_ec_ecdt_start() after acpi_ec_query_init()
in acpi_ec_init().
Link: https://jira01.devtools.intel.com/browse/LCK-4348 Fixes: 2a5708409e4e (ACPI / EC: Fix a gap that ECDT EC cannot handle EC events) Fixes: c712bb58d827 (ACPI / EC: Add support to skip boot stage DSDT probe) Reported-by: Wang Wendy <wendy.wang@intel.com> Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI HID for Hisilicon Hip07/08 should be HISI02A1/2,
not HISI0A21/2, HISI02A1/2 was tested ok but was modified
by the stupid typo when upstream the patches (by me),
correct them to the right IDs (matching the IDs in
drivers/i2c/busses/i2c-designware-platdrv.c).
Fixes: 6e14cf361a0c (ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller) Reported-by: Tao Tian <tiantao6@huawei.com> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log