VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
We currently don't validate the beacon head, i.e. the header,
fixed part and elements that are to go in front of the TIM
element. This means that the variable elements there can be
malformed, e.g. have a length exceeding the buffer size, but
most downstream code from this assumes that this has already
been checked.
Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it and since we'll need it, also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.
Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronization is recommended before disabling the trace registers
to prevent any start or stop points being speculative at the point
of disabling the unit (section 7.3.77 of ARM IHI 0064D).
Synchronization is also recommended after programming the trace
registers to ensure all updates are committed prior to normal code
resuming (section 4.3.7 of ARM IHI 0064D).
Let's ensure these syncronization points are present in the code
and clearly commented.
Note that we could rely on the barriers in CS_LOCK and
coresight_disclaim_device_unlocked or the context switch to user
space - however coresight may be of use in the kernel.
On armv8 the mb macro is defined as dsb(sy) - Given that the etm4x is
only used on armv8 let's directly use dsb(sy) instead of mb(). This
removes some ambiguity and makes it easier to correlate the code with
the TRM.
Signed-off-by: Andrew Murray <andrew.murray@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed capital letter for "use" in title] Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/20190829202842.580-11-mathieu.poirier@linaro.org Cc: stable@vger.kernel.org # 4.9+ Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today, put_compat_statfs64() disallows nearly any field value over
2^32 if f_bsize is only 32 bits, but that makes no sense.
compat_statfs64 is there for the explicit purpose of providing 64-bit
fields for f_files, f_ffree, etc. And f_bsize is always only 32 bits.
As a result, 32-bit userspace gets -EOVERFLOW for i.e. large file
counts even with -D_FILE_OFFSET_BITS=64 set.
In reality, only f_bsize and f_frsize can legitimately overflow
(fields like f_type and f_namelen should never be large), so test
only those fields.
This bug was discussed at length some time ago, and this is the proposal
Al suggested at https://lkml.org/lkml/2018/8/6/640. It seemed to get
dropped amid the discussion of other related changes, but this
part seems obviously correct on its own, so I've picked it up and
sent it, for expediency.
Fixes: 64d2ab32efe3 ("vfs: fix put_compat_statfs64() does not handle errors") Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prev_raw_counts is allocated when using intervals. This is used when
calculating the difference in the counts of events when using interval.
The current counts are stored in prev_raw_counts to calculate the
differences in the next iteration.
On the first interval of the second and subsequent repetitions,
prev_raw_counts would be the values stored in the last interval of the
previous repetitions, while the current counts will only be for the
first interval of the current repetition.
Hence there is a possibility of events showing up as big number.
Fix this by resetting prev_raw_counts whenever perf stat repeats the
command.
With the fix:
# perf stat -r 3 -I 2000 -e faults -e sched:sched_switch -a sleep 5
This was broken since the cset introducing the --interval feature, i.e.
--repeat + --interval wasn't tested at that point, add the Fixes tag so
that automatic scripts can pick this up.
Fixes: 13370a9b5bb8 ("perf stat: Add interval printing") Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org # v3.9+ Link: http://lore.kernel.org/lkml/20190904094738.9558-2-srikar@linux.vnet.ibm.com
[ Fixed up conflicts with libperf, i.e. some perf_{evsel,evlist} lost the 'perf' prefix ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Observe a segmentation fault when 'perf stat' is asked to repeat forever
with the interval option.
Without fix:
# perf stat -r 0 -I 5000 -e cycles -a sleep 10
# time counts unit events
5.000211692 3,13,89,82,34,157 cycles
10.000380119 1,53,98,52,22,294 cycles
10.040467280 17,16,79,265 cycles
Segmentation fault
This problem was only observed when we use forever option aka -r 0 and
works with limited repeats. Calling print_counter with ts being set to
NULL, is not a correct option when interval is set. Hence avoid
print_counter(NULL,..) if interval is set.
Did the 'git bisect' to find the cset introducing the problem to add the
Fixes tag below, and at that time the problem reproduced as:
(gdb) run stat -r0 -I500 sleep 1
<SNIP>
Program received signal SIGSEGV, Segmentation fault.
print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
866 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, csv_sep);
(gdb) bt
#0 print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
#1 0x000000000041860a in print_counters (ts=ts@entry=0x0, argc=argc@entry=2, argv=argv@entry=0x7fffffffd640) at builtin-stat.c:938
#2 0x0000000000419a7f in cmd_stat (argc=2, argv=0x7fffffffd640, prefix=<optimized out>) at builtin-stat.c:1411
#3 0x000000000045c65a in run_builtin (p=p@entry=0x6291b8 <commands+216>, argc=argc@entry=5, argv=argv@entry=0x7fffffffd640) at perf.c:370
#4 0x000000000045c893 in handle_internal_command (argc=5, argv=0x7fffffffd640) at perf.c:429
#5 0x000000000045c8f1 in run_argv (argcp=argcp@entry=0x7fffffffd4ac, argv=argv@entry=0x7fffffffd4a0) at perf.c:473
#6 0x000000000045cac9 in main (argc=<optimized out>, argv=<optimized out>) at perf.c:588
(gdb)
Mostly the same as just before this patch:
Program received signal SIGSEGV, Segmentation fault.
0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
964 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep);
(gdb) bt
#0 0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
#1 0x0000000000588047 in perf_evlist__print_counters (evlist=0xbc9b90, config=0xa1f2a0 <stat_config>, _target=0xa1f0c0 <target>, ts=0x0, argc=2, argv=0x7fffffffd670)
at util/stat-display.c:1172
#2 0x000000000045390f in print_counters (ts=0x0, argc=2, argv=0x7fffffffd670) at builtin-stat.c:656
#3 0x0000000000456bb5 in cmd_stat (argc=2, argv=0x7fffffffd670) at builtin-stat.c:1960
#4 0x00000000004dd2e0 in run_builtin (p=0xa30e00 <commands+288>, argc=5, argv=0x7fffffffd670) at perf.c:310
#5 0x00000000004dd54d in handle_internal_command (argc=5, argv=0x7fffffffd670) at perf.c:362
#6 0x00000000004dd694 in run_argv (argcp=0x7fffffffd4cc, argv=0x7fffffffd4c0) at perf.c:406
#7 0x00000000004dda11 in main (argc=5, argv=0x7fffffffd670) at perf.c:531
(gdb)
Fixes: d4f63a4741a8 ("perf stat: Introduce print_counters function") Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # v4.2+ Link: http://lore.kernel.org/lkml/20190904094738.9558-3-srikar@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We release wrong pointer on error path in cpu_cache_level__read
function, leading to segfault:
(gdb) r record ls
Starting program: /root/perf/tools/perf/perf record ls
...
[ perf record: Woken up 1 times to write data ]
double free or corruption (out)
Thread 1 "perf" received signal SIGABRT, Aborted.
0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
(gdb) bt
#0 0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6
#1 0x00007ffff7443bac in abort () from /lib64/power9/libc.so.6
#2 0x00007ffff74af8bc in __libc_message () from /lib64/power9/libc.so.6
#3 0x00007ffff74b92b8 in malloc_printerr () from /lib64/power9/libc.so.6
#4 0x00007ffff74bb874 in _int_free () from /lib64/power9/libc.so.6
#5 0x0000000010271260 in __zfree (ptr=0x7fffffffa0b0) at ../../lib/zalloc..
#6 0x0000000010139340 in cpu_cache_level__read (cache=0x7fffffffa090, cac..
#7 0x0000000010143c90 in build_caches (cntp=0x7fffffffa118, size=<optimiz..
...
Releasing the proper pointer.
Fixes: 720e98b5faf1 ("perf tools: Add perf data cache feature") Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org: # v4.6+ Link: http://lore.kernel.org/lkml/20190912105235.10689-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a cpu requests broadcasting, before starting the tick broadcast
hrtimer, bc_set_next() checks if the timer callback (bc_handler) is active
using hrtimer_try_to_cancel(). But hrtimer_try_to_cancel() does not provide
the required synchronization when the callback is active on other core.
The callback could have already executed tick_handle_oneshot_broadcast()
and could have also returned. But still there is a small time window where
the hrtimer_try_to_cancel() returns -1. In that case bc_set_next() returns
without doing anything, but the next_event of the tick broadcast clock
device is already set to a timeout value.
In the race condition diagram below, CPU #1 is running the timer callback
and CPU #2 is entering idle state and so calls bc_set_next().
In the worst case, the next_event will contain an expiry time, but the
hrtimer will not be started which happens when the racing callback returns
HRTIMER_NORESTART. The hrtimer might never recover if all further requests
from the CPUs to subscribe to tick broadcast have timeout greater than the
next_event of tick broadcast clock device. This leads to cascading of
failures and finally noticed as rcu stall warnings
Here is a depiction of the race condition
CPU #1 (Running timer callback) CPU #2 (Enter idle
and subscribe to
tick broadcast)
--------------------- ---------------------
__run_hrtimer() tick_broadcast_enter()
bc_handler() __tick_broadcast_oneshot_control()
tick_handle_oneshot_broadcast()
raw_spin_lock(&tick_broadcast_lock);
dev->next_event = KTIME_MAX; //wait for tick_broadcast_lock
//next_event for tick broadcast clock
set to KTIME_MAX since no other cores
subscribed to tick broadcasting
raw_spin_unlock(&tick_broadcast_lock);
if (dev->next_event == KTIME_MAX)
return HRTIMER_NORESTART
// callback function exits without
restarting the hrtimer //tick_broadcast_lock acquired
raw_spin_lock(&tick_broadcast_lock);
tick_broadcast_set_event()
clockevents_program_event()
dev->next_event = expires;
bc_set_next()
hrtimer_try_to_cancel()
//returns -1 since the timer
callback is active. Exits without
restarting the timer
cpu_base->running = NULL;
The comment that hrtimer cannot be armed from within the callback is
wrong. It is fine to start the hrtimer from within the callback. Also it is
safe to start the hrtimer from the enter/exit idle code while the broadcast
handler is active. The enter/exit idle code and the broadcast handler are
synchronized using tick_broadcast_lock. So there is no need for the
existing try to cancel logic. All this can be removed which will eliminate
the race condition as well.
Fixes: 5d1638acb9f6 ("tick: Introduce hrtimer based broadcast") Originally-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Balasubramani Vivekanandan <balasubramani_vivekanandan@mentor.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190926135101.12102-2-balasubramani_vivekanandan@mentor.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the re-allocation of tep->cmdlines succeeds, then the previous
allocation of tep->cmdlines will be freed. If we later fail in
add_new_comm(), we must not free cmdlines, and also should assign
tep->cmdlines to the new allocation. Otherwise when freeing tep, the
tep->cmdlines will be pointing to garbage.
Fixes: a6d2a61ac653a ("tools lib traceevent: Remove some die() calls") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20190828191819.970121417@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The calls to arch_add_memory()/arch_remove_memory() are always made
with the read-side cpu_hotplug_lock acquired via memory_hotplug_begin().
On pSeries, arch_add_memory()/arch_remove_memory() eventually call
resize_hpt() which in turn calls stop_machine() which acquires the
read-side cpu_hotplug_lock again, thereby resulting in the recursive
acquisition of this lock.
In the absence of CONFIG_PROVE_LOCKING, we hadn't observed a system
lockup during a memory hotplug operation because cpus_read_lock() is a
per-cpu rwsem read, which, in the fast-path (in the absence of the
writer, which in our case is a CPU-hotplug operation) simply
increments the read_count on the semaphore. Thus a recursive read in
the fast-path doesn't cause any problems.
However, we can hit this problem in practice if there is a concurrent
CPU-Hotplug operation in progress which is waiting to acquire the
write-side of the lock. This will cause the second recursive read to
block until the writer finishes. While the writer is blocked since the
first read holds the lock. Thus both the reader as well as the writers
fail to make any progress thereby blocking both CPU-Hotplug as well as
Memory Hotplug operations.
Memory-Hotplug CPU-Hotplug
CPU 0 CPU 1
------ ------
that limited the number of devices to 256. Before the patch we could
create 1000s of devices, but the patch switched us from using our
own thread to using a work queue which has a default limit of 256
active works.
The problem is that our recv_work function sits in a loop until
disconnection but only handles IO for one connection. The work is
started when the connection is started/restarted, but if we end up
creating 257 or more connections, the queue_work call just queues
connection257+'s recv_work and that waits for connection 1 - 256's
recv_work to be disconnected and that work instance completing.
Instead of reverting back to kthreads, this has us allocate a
workqueue_struct per device, so we can block in the work.
Cc: stable@vger.kernel.org Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This will allow the blksize to be set zero and then use 1024 as
default.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Xiubo Li <xiubli@redhat.com>
[fix to use goto out instead of return in genl_connect] Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a vCPU is brought done, the XIVE VP (Virtual Processor) is first
disabled and then the event notification queues are freed. When freeing
the queues, we check for possible escalation interrupts and free them
also.
But when a XIVE VP is disabled, the underlying XIVE ENDs also are
disabled in OPAL. When an END (Event Notification Descriptor) is
disabled, its ESB pages (ESn and ESe) are disabled and loads return all
1s. Which means that any access on the ESB page of the escalation
interrupt will return invalid values.
When an interrupt is freed, the shutdown handler computes a 'saved_p'
field from the value returned by a load in xive_do_source_set_mask().
This value is incorrect for escalation interrupts for the reason
described above.
This has no impact on Linux/KVM today because we don't make use of it
but we will introduce in future changes a xive_get_irqchip_state()
handler. This handler will use the 'saved_p' field to return the state
of an interrupt and 'saved_p' being incorrect, softlockup will occur.
Fix the vCPU cleanup sequence by first freeing the escalation interrupts
if any, then disable the XIVE VP and last free the queues.
Fixes: 90c73795afa2 ("KVM: PPC: Book3S HV: Add a new KVM device for the XIVE native exploitation mode") Fixes: 5af50993850a ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190806172538.5087-1-clg@kaod.org Signed-off-by: Sasha Levin <sashal@kernel.org>
An oops can be triggered in the scheduler when running qemu on arm64:
Unable to handle kernel paging request at virtual address ffff000008effe40
Internal error: Oops: 96000007 [#1] SMP
Process migration/0 (pid: 12, stack limit = 0x00000000084e3736)
pstate: 20000085 (nzCv daIf -PAN -UAO)
pc : __ll_sc___cmpxchg_case_acq_4+0x4/0x20
lr : move_queued_task.isra.21+0x124/0x298
...
Call trace:
__ll_sc___cmpxchg_case_acq_4+0x4/0x20
__migrate_task+0xc8/0xe0
migration_cpu_stop+0x170/0x180
cpu_stopper_thread+0xec/0x178
smpboot_thread_fn+0x1ac/0x1e8
kthread+0x134/0x138
ret_from_fork+0x10/0x18
__set_cpus_allowed_ptr() will choose an active dest_cpu in affinity mask to
migrage the process if process is not currently running on any one of the
CPUs specified in affinity mask. __set_cpus_allowed_ptr() will choose an
invalid dest_cpu (dest_cpu >= nr_cpu_ids, 1024 in my virtual machine) if
CPUS in an affinity mask are deactived by cpu_down after cpumask_intersects
check. cpumask_test_cpu() of dest_cpu afterwards is overflown and may pass if
corresponding bit is coincidentally set. As a consequence, kernel will
access an invalid rq address associate with the invalid CPU in
migration_cpu_stop->__migrate_task->move_queued_task and the Oops occurs.
The reproduce the crash:
1) A process repeatedly binds itself to cpu0 and cpu1 in turn by calling
sched_setaffinity.
2) A shell script repeatedly does "echo 0 > /sys/devices/system/cpu/cpu1/online"
and "echo 1 > /sys/devices/system/cpu/cpu1/online" in turn.
3) Oops appears if the invalid CPU is set in memory after tested cpumask.
Signed-off-by: KeMeng Shi <shikemeng@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1568616808-16808-1-git-send-email-shikemeng@huawei.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
thermal_zone_device_unregister() cancels the delayed work that polls the
thermal zone, but it does not wait for it to finish. This is racy with
respect to the freeing of the thermal zone device, which can result in a
use-after-free [1].
Fix this by waiting for the delayed work to finish before freeing the
thermal zone device. Note that thermal_zone_device_set_polling() is
never invoked from an atomic context, so it is safe to call
cancel_delayed_work_sync() that can block.
[1]
[ +0.002221] ==================================================================
[ +0.000064] BUG: KASAN: use-after-free in __mutex_lock+0x1076/0x11c0
[ +0.000016] Read of size 8 at addr ffff8881e48e0450 by task kworker/1:0/17
LPTimer can use a 32KHz clock for counting. It depends on clock tree
configuration. In such a case, PWM output frequency range is limited.
Although unlikely, nothing prevents user from requesting a PWM frequency
above counting clock (32KHz for instance):
- This causes (prd - 1) = 0xffff to be written in ARR register later in
the apply() routine.
This results in badly configured PWM period (and also duty_cycle).
Add a check to report an error is such a case.
IF the server rejected our layout return with a state error such as
NFS4ERR_BAD_STATEID, or even a stale inode error, then we do want
to clear out all the remaining layout segments and mark that stateid
as invalid.
Do not try to allocate any amount of memory requested by the user.
Instead limit it to 128 registers. Actually the longest series of
consecutive allowed registers are 48, mmGB_TILE_MODE0-31 and
mmGB_MACROTILE_MODE0-15 (0x2644-0x2673).
... this works:
nft add rule ip filter input add @set1 { ip saddr }
-> whenever rule is triggered, the source ip address is inserted
into the set (if it did not exist).
This won't work:
nft add rule ip filter input ip saddr @set1 counter
Error: Could not process rule: Operation not supported
In other words, we can add entries to the set, but then can't make
matching decision based on that set.
That is just wrong -- all set backends support lookups (else they would
not be very useful).
The failure comes from an explicit rejection in nft_lookup.c.
Looking at the history, it seems like NFT_SET_EVAL used to mean
'set contains expressions' (aka. "is a meter"), for instance something like
nft add rule ip filter input meter example { ip saddr limit rate 10/second }
or
nft add rule ip filter input meter example { ip saddr counter }
The actual meaning of NFT_SET_EVAL however, is
'set can be updated from the packet path'.
'meters' and packet-path insertions into sets, such as
'add @set { ip saddr }' use exactly the same kernel code (nft_dynset.c)
and thus require a set backend that provides the ->update() function.
The only set that provides this also is the only one that has the
NFT_SET_EVAL feature flag.
Removing the wrong check makes the above example work.
While at it, also fix the flag check during set instantiation to
allow supported combinations only.
Fixes: 8aeff920dcc9b3f ("netfilter: nf_tables: add stateful object reference to set elements") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If client mds session is evicted in CEPH_MDS_SESSION_OPENING state,
mds won't send session msg to client, and delayed_work skip
CEPH_MDS_SESSION_OPENING state session, the session hang forever.
Allow ceph_con_keepalive to reconnect a session in OPENING to avoid
session hang. Also, ensure that we skip sessions in RESTARTING and
REJECTED states since those states can't be resurrected by issuing
a keepalive.
When filling an inode with info from the MDS, i_blkbits is being
initialized using fl_stripe_unit, which contains the stripe unit in
bytes. Unfortunately, this doesn't make sense for directories as they
have fl_stripe_unit set to '0'. This means that i_blkbits will be set
to 0xff, causing an UBSAN undefined behaviour in i_blocksize():
UBSAN: Undefined behaviour in ./include/linux/fs.h:731:12
shift exponent 255 is too large for 32-bit type 'int'
Fix this by initializing i_blkbits to CEPH_BLOCK_SHIFT if fl_stripe_unit
is zero.
Signed-off-by: Luis Henriques <lhenriques@suse.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If MCFG area is not reserved in E820, Xen by default will defer its usage
until Dom0 registers it explicitly after ACPI parser recognizes it as
a reserved resource in DSDT. Having it reserved in E820 is not
mandatory according to "PCI Firmware Specification, rev 3.2" (par. 4.1.2)
and firmware is free to keep a hole in E820 in that place. Xen doesn't know
what exactly is inside this hole since it lacks full ACPI view of the
platform therefore it's potentially harmful to access MCFG region
without additional checks as some machines are known to provide
inconsistent information on the size of the region.
Now xen_mcfg_late() runs after acpi_init() which is too late as some basic
PCI enumeration starts exactly there as well. Trying to register a device
prior to MCFG reservation causes multiple problems with PCIe extended
capability initializations in Xen (e.g. SR-IOV VF BAR sizing). There are
no convenient hooks for us to subscribe to so register MCFG areas earlier
upon the first invocation of xen_add_device(). It should be safe to do once
since all the boot time buses must have their MCFG areas in MCFG table
already and we don't support PCI bus hot-plug.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently on mmap cache policy, we always attach writeback_fid
whether mmap type is SHARED or PRIVATE. However, in the use case
of kata-container which combines 9p(Guest OS) with overlayfs(Host OS),
this behavior will trigger overlayfs' copy-up when excute command
inside container.
In encode_attrs(), there is an if statement on line 1145 to check
whether label is NULL:
if (label && (attrmask[2] & FATTR4_WORD2_SECURITY_LABEL))
When label is NULL, it is used on lines 1178-1181:
*p++ = cpu_to_be32(label->lfs);
*p++ = cpu_to_be32(label->pi);
*p++ = cpu_to_be32(label->len);
p = xdr_encode_opaque_fixed(p, label->label, label->len);
To fix these bugs, label is checked before being used.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
integrity_kernel_read() returns the number of bytes read. If this is
a short read then this positive value is returned from
ima_calc_file_hash_atfm(). Currently this is only indirectly called from
ima_calc_file_hash() and this function only tests for the return value
being zero or nonzero and also doesn't forward the return value.
Nevertheless there's no point in returning a positive value as an error,
so translate a short read into -EINVAL.
In a few places we don't properly initialize on-stack chandefs,
resulting in EDMG data to be non-zero, which broke things.
Additionally, in a few places we rely on the driver to init the
data completely, but perhaps we shouldn't as non-EDMG drivers
may not initialize the EDMG data, also initialize it there.
Cc: stable@vger.kernel.org Fixes: 2a38075cd0be ("nl80211: Add support for EDMG channels") Reported-by: Dmitry Osipenko <digetx@gmail.com> Tested-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/1569239475-I2dcce394ecf873376c386a78f31c2ec8b538fa25@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a user process using xenbus has open transactions and is killed
e.g. via ctrl-C the following cleanup of the allocated resources might
result in a deadlock due to trying to end a transaction in the xenbus
worker thread:
This patch reverts commit 75437bb304b20 (locking/pvqspinlock: Don't
wait if vCPU is preempted). A large performance regression was caused
by this commit. on over-subscription scenarios.
The test was run on a Xeon Skylake box, 2 sockets, 40 cores, 80 threads,
with three VMs of 80 vCPUs each. The score of ebizzy -M is reduced from
13000-14000 records/s to 1700-1800 records/s:
Exit from aggressive wait-early mechanism can result in premature yield
and extra scheduling latency.
Actually, only 6% of wait_early events are caused by vcpu_is_preempted()
being true. However, when one vCPU voluntarily releases its vCPU, all
the subsequently waiters in the queue will do the same and the cascading
effect leads to bad performance.
kvm optimizations:
[1] commit d73eb57b80b (KVM: Boost vCPUs that are delivering interrupts)
[2] commit 266e85a5ec9 (KVM: X86: Boost queue head vCPU to mitigate lock waiter preemption)
Tested-by: loobinliu@tencent.com Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Waiman Long <longman@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: loobinliu@tencent.com Cc: stable@vger.kernel.org Fixes: 75437bb304b20 (locking/pvqspinlock: Don't wait if vCPU is preempted) Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must not unconditionally set the DMA snoop bit; if the DMA API is
assuming that the device is not DMA coherent, and the device snoops the
CPU caches, the device can see stale cache lines brought in by
speculative prefetch.
This leads to the device seeing stale data, potentially resulting in
corrupted data transfers. Commonly, this results in a descriptor fetch
error such as:
but can lead to other errors, and potentially direct the SDHCI
controller to read/write data to other memory locations (e.g. if a valid
descriptor is visible to the device in a stale cache line.)
Fix this by ensuring that the DMA snoop bit corresponds with the
behaviour of the DMA API. Since the driver currently only supports DT,
use of_dma_is_coherent(). Note that device_get_dma_attr() can not be
used as that risks re-introducing this bug if/when the driver is
converted to ACPI.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.
Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().
We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service. What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered. Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP36xx and AM/DM37x TRMs say that the maximum divider for DSS fclk
(in CM_CLKSEL_DSS) is 32. Experimentation shows that this is not
correct, and using divider of 32 breaks DSS with a flood or underflows
and sync losts. Dividers up to 31 seem to work fine.
There is another patch to the DT files to limit the divider correctly,
but as the DSS driver also needs to know the maximum divider to be able
to iteratively find good rates, we also need to do the fix in the DSS
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Adam Ford <aford173@gmail.com> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20191002122542.8449-1-tomi.valkeinen@ti.com Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Converting from ms to s requires dividing by 1000, not multiplying. So
this is currently taking the smaller of new_timeout and 1.28e8,
i.e. effectively new_timeout.
The driver knows what it set max_hw_heartbeat_ms to, so use that
value instead of doing a division at run-time.
FWIW, this can easily be tested by booting into a busybox shell and
doing "watchdog -t 5 -T 130 /dev/watchdog" - without this patch, the
watchdog fires after 130&127 == 2 seconds.
Fixes: b07e228eee69 "watchdog: imx2_wdt: Fix set_timeout for big timeout values" Cc: stable@vger.kernel.org # 5.2 plus anything the above got backported to Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190812131356.23039-1-linux@rasmusvillemoes.dk Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that the code in collect_expired_timers() uses jiffies
unprotected:
if (next_event > jiffies)
base->clk = jiffies;
As the compiler is allowed to reload the value base->clk can advance
between the check and the store and in the worst case advance farther than
next event. That causes the timer expiry to be delayed until the wheel
pointer wraps around.
Convert the code to use READ_ONCE()
Fixes: 236968383cf5 ("timers: Optimize collect_expired_timers() for NOHZ") Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Liang ZhiCheng <liangzhicheng@baidu.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1568894687-14499-1-git-send-email-lirongqing@baidu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
all execve()s will fail due to argv copying into kmap()ed pages, and on
usercopy checking the calls ultimately of virt_to_page() will be looking
for "bad" kmap (highmem) pointers due to CONFIG_DEBUG_VIRTUAL=y:
kaddr = kmap(kmapped_page);
...
if (copy_from_user(kaddr+offset, str, bytes_to_copy)) ...
Now we can fetch the correct page to avoid the pfn check. In both cases,
hardened usercopy will need to walk the page-span checker (if enabled)
to do sanity checking.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Fixes: f5509cc18daa ("mm: Hardened usercopy") Cc: Matthew Wilcox <willy@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Link: https://lore.kernel.org/r/201909171056.7F2FFD17@keescook Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IV transfer from ofifo to class2 (set up at [29][30]) is not guaranteed
to be scheduled before the data transfer from ofifo to external memory
(set up at [38]:
If ofifo -> external memory transfer happens first, DECO will hang
(issuing a Watchdog Timeout error, if WDOG is enabled) waiting for
data availability in ofifo for the ofifo -> c2 ififo transfer.
Make sure IV transfer happens first by waiting for all CAAM internal
transfers to end before starting payload transfer.
New descriptor with jump command inserted at [37]:
[Note: the issue is present in the descriptor from the very beginning
(cf. Fixes tag). However I've marked it v4.19+ since it's the oldest
maintained kernel that the patch applies clean against.]
skcipher_walk_done may be called with an error by internal or
external callers. For those internal callers we shouldn't unmap
pages but for external callers we must unmap any pages that are
in use.
This patch distinguishes between the two cases by checking whether
walk->nbytes is zero or not. For internal callers, we now set
walk->nbytes to zero prior to the call. For external callers,
walk->nbytes has always been non-zero (as zero is used to indicate
the termination of a walk).
It seems that smp_processor_id() is only used for a best-effort
load-balancing, refer to qat_crypto_get_instance_node(). It's not feasible
to disable preemption for the duration of the crypto requests. Therefore,
just silence the warning. This commit is similar to e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").
Silences the following splat:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/2904
caller is qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
CPU: 1 PID: 2904 Comm: cryptomgr_test Tainted: P O 4.14.69 #1
...
Call Trace:
dump_stack+0x5f/0x86
check_preemption_disabled+0xd3/0xe0
qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
skcipher_setkey_ablkcipher+0x2b/0x40
__test_skcipher+0x1f3/0xb20
? cpumask_next_and+0x26/0x40
? find_busiest_group+0x10e/0x9d0
? preempt_count_add+0x49/0xa0
? try_module_get+0x61/0xf0
? crypto_mod_get+0x15/0x30
? __kmalloc+0x1df/0x1f0
? __crypto_alloc_tfm+0x116/0x180
? crypto_skcipher_init_tfm+0xa6/0x180
? crypto_create_tfm+0x4b/0xf0
test_skcipher+0x21/0xa0
alg_test_skcipher+0x3f/0xa0
alg_test.part.6+0x126/0x2a0
? finish_task_switch+0x21b/0x260
? __schedule+0x1e9/0x800
? __wake_up_common+0x8d/0x140
cryptomgr_test+0x40/0x50
kthread+0xff/0x130
? cryptomgr_notify+0x540/0x540
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x24/0x50
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tools/lib/traceevent/Makefile had a test added to it to detect a failure
of the "nm" when making the dynamic list file (whatever that is). The
problem is that the test sorts the values "U W w" and some versions of sort
will place "w" ahead of "W" (even though it has a higher ASCII value, and
break the test.
Add 'tr "w" "W"' to merge the two and not worry about the ordering.
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Carrillo-Cisneros <davidcc@google.com> Cc: He Kuang <hekuang@huawei.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Michal rarek <mmarek@suse.com> Cc: Paul Turner <pjt@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Wang Nan <wangnan0@huawei.com> Cc: stable@vger.kernel.org Fixes: 6467753d61399 ("tools lib traceevent: Robustify do_generate_dynamic_list_file") Link: http://lkml.kernel.org/r/20190805130150.25acfeb1@gandalf.local.home Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kHz to Hz is incorrectly converted in a few places in the code,
this results in a wrong frequency being calculated because devfreq core
uses OPP frequencies that are given in Hz to clamp the rate, while
tegra-devfreq gives to the core value in kHz and then it also expects to
receive value in kHz from the core. In a result memory freq is always set
to a value which is close to ULONG_MAX because of the bug. Hence the EMC
frequency is always capped to the maximum and the driver doesn't do
anything useful. This patch was tested on Tegra30 and Tegra124 SoC's, EMC
frequency scaling works properly now.
Jack Wang [Mon, 7 Oct 2019 12:36:53 +0000 (14:36 +0200)]
KVM: nVMX: handle page fault in vmread fix
During backport f7eea636c3d5 ("KVM: nVMX: handle page fault in vmread"),
there was a mistake the exception reference should be passed to function
kvm_write_guest_virt_system, instead of NULL, other wise, we will get
NULL pointer deref, eg
On POWER9, when userspace reads the value of the DPDES register on a
vCPU, it is possible for 0 to be returned although there is a doorbell
interrupt pending for the vCPU. This can lead to a doorbell interrupt
being lost across migration. If the guest kernel uses doorbell
interrupts for IPIs, then it could malfunction because of the lost
interrupt.
This happens because a newly-generated doorbell interrupt is signalled
by setting vcpu->arch.doorbell_request to 1; the DPDES value in
vcpu->arch.vcore->dpdes is not updated, because it can only be updated
when holding the vcpu mutex, in order to avoid races.
To fix this, we OR in vcpu->arch.doorbell_request when reading the
DPDES value.
ccw console is created early in start_kernel and used before css is
initialized or ccw console subchannel is registered. Until then console
subchannel does not have a parent. For that reason assume subchannels
with no parent are not pseudo subchannels. This fixes the following
kasan finding:
BUG: KASAN: global-out-of-bounds in sch_is_pseudo_sch+0x8e/0x98
Read of size 8 at addr 00000000000005e8 by task swapper/0/0
Fix the following kasan finding:
BUG: KASAN: global-out-of-bounds in ccwgroup_create_dev+0x850/0x1140
Read of size 1 at addr 0000000000000000 by task systemd-udevd.r/561
If the KVM_S390_MEM_OP ioctl is called with an access register >= 16,
then there is certainly a bug in the calling userspace application.
We check for wrong access registers, but only if the vCPU was already
in the access register mode before (i.e. the SIE block has recorded
it). The check is also buried somewhere deep in the calling chain (in
the function ar_translation()), so this is somewhat hard to find.
It's better to always report an error to the userspace in case this
field is set wrong, and it's safer in the KVM code if we block wrong
values here early instead of relying on a check somewhere deep down
the calling chain, so let's add another check to kvm_s390_guest_mem_op()
directly.
We also should check that the "size" is non-zero here (thanks to Janosch
Frank for the hint!). If we do not check the size, we could call vmalloc()
with this 0 value, and this will cause a kernel warning.
Signed-off-by: Thomas Huth <thuth@redhat.com> Link: https://lkml.kernel.org/r/20190829122517.31042-1-thuth@redhat.com Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With THREAD_INFO_IN_TASK (which is selected on s390) task's stack usage
is refcounted and should always be protected by get/put when touching
other task's stack to avoid race conditions with task's destruction code.
syzbot found that a thread can stall for minutes inside kexec_load() after
that thread was killed by SIGKILL [1]. It turned out that the reproducer
was trying to allocate 2408MB of memory using kimage_alloc_page() from
kimage_load_normal_segment(). Let's check for SIGKILL before doing memory
allocation.
nfc_genl_deactivate_target() relies on the NFC_ATTR_TARGET_INDEX
attribute being present, but doesn't check whether it is actually
provided by the user. Same goes for nfc_genl_fw_download() and
NFC_ATTR_FIRMWARE_NAME.
This patch adds appropriate checks.
Found with syzkaller.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inode_smack::smk_lock is taken during smack_d_instantiate(), which is
called during a filesystem transaction when creating a file on ext4.
Therefore to avoid a deadlock, all code that takes this lock must use
GFP_NOFS, to prevent memory reclaim from waiting for the filesystem
transaction to complete.
There is a logic bug in the current smack_bprm_set_creds():
If LSM_UNSAFE_PTRACE is set, but the ptrace state is deemed to be
acceptable (e.g. because the ptracer detached in the meantime), the other
->unsafe flags aren't checked. As far as I can tell, this means that
something like the following could work (but I haven't tested it):
- task A: create task B with fork()
- task B: set NO_NEW_PRIVS
- task B: install a seccomp filter that makes open() return 0 under some
conditions
- task B: replace fd 0 with a malicious library
- task A: attach to task B with PTRACE_ATTACH
- task B: execve() a file with an SMACK64EXEC extended attribute
- task A: while task B is still in the middle of execve(), exit (which
destroys the ptrace relationship)
Make sure that if any flags other than LSM_UNSAFE_PTRACE are set in
bprm->unsafe, we reject the execve().
Cc: stable@vger.kernel.org Fixes: 5663884caab1 ("Smack: unify all ptrace accesses in the smack") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in __ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.
Since the DAD sequence can not be aborted, add a check for the missing
host route in __ipv6_ifa_notify. The only way this should happen is due
to the previously mentioned race. The host route is created when the
address is added to an interface; it is only removed on a down event
where the address is kept. Add a warning if the host route is missing
AND the device is up; this is a situation that should never happen.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have identified a problem with the "oversubscription" policy in the
link transmission code.
When small messages are transmitted, and the sending link has reached
the transmit window limit, those messages will be bundled and put into
the link backlog queue. However, bundles of data messages are counted
at the 'CRITICAL' level, so that the counter for that level, instead of
the counter for the real, bundled message's level is the one being
increased.
Subsequent, to-be-bundled data messages at non-CRITICAL levels continue
to be tested against the unchanged counter for their own level, while
contributing to an unrestrained increase at the CRITICAL backlog level.
This leaves a gap in congestion control algorithm for small messages
that can result in starvation for other users or a "real" CRITICAL
user. Even that eventually can lead to buffer exhaustion & link reset.
We fix this by keeping a 'target_bskb' buffer pointer at each levels,
then when bundling, we only bundle messages at the same importance
level only. This way, we know exactly how many slots a certain level
have occupied in the queue, so can manage level congestion accurately.
By bundling messages at the same level, we even have more benefits. Let
consider this:
- One socket sends 64-byte messages at the 'CRITICAL' level;
- Another sends 4096-byte messages at the 'LOW' level;
When a 64-byte message comes and is bundled the first time, we put the
overhead of message bundle to it (+ 40-byte header, data copy, etc.)
for later use, but the next message can be a 4096-byte one that cannot
be bundled to the previous one. This means the last bundle carries only
one payload message which is totally inefficient, as for the receiver
also! Later on, another 64-byte message comes, now we make a new bundle
and the same story repeats...
With the new bundling algorithm, this will not happen, the 64-byte
messages will be bundled together even when the 4096-byte message(s)
comes in between. However, if the 4096-byte messages are sent at the
same level i.e. 'CRITICAL', the bundling algorithm will again cause the
same overhead.
Also, the same will happen even with only one socket sending small
messages at a rate close to the link transmit's one, so that, when one
message is bundled, it's transmitted shortly. Then, another message
comes, a new bundle is created and so on...
We will solve this issue radically by another patch.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Reported-by: Hoang Le <hoang.h.le@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xennet_fill_frags() uses ~0U as return value when the sk_buff is not able
to cache extra fragments. This is incorrect because the return type of
xennet_fill_frags() is RING_IDX and 0xffffffff is an expected value for
ring buffer index.
In the situation when the rsp_cons is approaching 0xffffffff, the return
value of xennet_fill_frags() may become 0xffffffff which xennet_poll() (the
caller) would regard as error. As a result, queue->rx.rsp_cons is set
incorrectly because it is updated only when there is error. If there is no
error, xennet_poll() would be responsible to update queue->rx.rsp_cons.
Finally, queue->rx.rsp_cons would point to the rx ring buffer entries whose
queue->rx_skbs[i] and queue->grant_rx_ref[i] are already cleared to NULL.
This leads to NULL pointer access in the next iteration to process rx ring
buffer entries.
The symptom is similar to the one fixed in
commit 00b368502d18 ("xen-netfront: do not assume sk_buff_head list is
empty in error handling").
This patch changes the return type of xennet_fill_frags() to indicate
whether it is successful or failed. The queue->rx.rsp_cons will be
always updated inside this function.
Fixes: ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rds_ibdev:ipaddr_list and rds_ibdev:conn_list are initialized
after allocation some resources such as protection domain.
If allocation of such resources fail, then these uninitialized
variables are accessed in rds_ib_dev_free() in failure path. This
can potentially crash the system. The code has been updated to
initialize these variables very early in the function.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Sudhakar Dindukurti <sudhakar.dindukurti@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep is unhappy if two locks from the same class are held.
Fix the below warning for hyperv and virtio sockets (vmci socket code
doesn't have the issue) by using lock_sock_nested() when __vsock_release()
is called recursively:
============================================
WARNING: possible recursive locking detected
5.3.0+ #1 Not tainted
--------------------------------------------
server/1795 is trying to acquire lock: ffff8880c5158990 (sk_lock-AF_VSOCK){+.+.}, at: hvs_release+0x10/0x120 [hv_sock]
but task is already holding lock: ffff8880c5158150 (sk_lock-AF_VSOCK){+.+.}, at: __vsock_release+0x2e/0xf0 [vsock]
other info that might help us debug this:
Possible unsafe locking scenario:
Fixes: 758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "reuse->sock[]" array is shared by multiple sockets. The going away
sk must unpublish itself from "reuse->sock[]" before making call_rcu()
call. However, this unpublish-action is currently done after a grace
period and it may cause use-after-free.
The fix is to move reuseport_detach_sock() to sk_destruct().
Due to the above reason, any socket with sk_reuseport_cb has
to go through the rcu grace period before freeing it.
It is a rather old bug (~3 yrs). The Fixes tag is not necessary
the right commit but it is the one that introduced the SOCK_RCU_FREE
logic and this fix is depending on it.
Fixes: a4298e4522d6 ("net: add SOCK_RCU_FREE socket flag") Cc: Eric Dumazet <eric.dumazet@gmail.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c09551c6ff7f ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.
If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.
Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().
Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.
The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.
Reported-by: Xiumei Mu <xmu@redhat.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This began with a syzbot report. syzkaller was injecting
IPv6 TCP SYN packets having a v4mapped source address.
After an unsuccessful 4-tuple lookup, TCP creates a request
socket (SYN_RECV) and calls reqsk_queue_hash_req()
reqsk_queue_hash_req() calls sk_ehashfn(sk)
At this point we have AF_INET6 sockets, and the heuristic
used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses
is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr)
For the particular spoofed packet, we end up hashing V4 addresses
which were not initialized by the TCP IPv6 stack, so KMSAN fired
a warning.
I first fixed sk_ehashfn() to test both source and destination addresses,
but then faced various problems, including user-space programs
like packetdrill that had similar assumptions.
Instead of trying to fix the whole ecosystem, it is better
to admit that we have a dual stack behavior, and that we
can not build linux kernels without V4 stack anyway.
The dual stack API automatically forces the traffic to be IPv4
if v4mapped addresses are used at bind() or connect(), so it makes
no sense to allow IPv6 traffic to use the same v4mapped class.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 542f54823614 ("tty: Modem functions for the HSO driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
erspan driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the erspan device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Tested:
Before patch:
# ip link set erspan0 mtu 1600
Error: mtu greater than device maximum.
After patch:
# ip link set erspan0 mtu 1600
# ip -d link show erspan0
21: erspan0@NONE: <BROADCAST,MULTICAST> mtu 1600 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 0
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD") Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzkaller managed to trigger the warning in bpf_jit_free() which checks via
bpf_prog_kallsyms_verify_off() for potentially unlinked JITed BPF progs
in kallsyms, and subsequently trips over GPF when walking kallsyms entries:
Upon further debugging, it turns out that whenever we trigger this
issue, the kallsyms removal in bpf_prog_ksym_node_del() was /skipped/
but yet bpf_jit_free() reported that the entry is /in use/.
Problem is that symbol exposure via bpf_prog_kallsyms_add() but also
perf_event_bpf_event() were done /after/ bpf_prog_new_fd(). Once the
fd is exposed to the public, a parallel close request came in right
before we attempted to do the bpf_prog_kallsyms_add().
Given at this time the prog reference count is one, we start to rip
everything underneath us via bpf_prog_release() -> bpf_prog_put().
The memory is eventually released via deferred free, so we're seeing
that bpf_jit_free() has a kallsym entry because we added it from
bpf_prog_load() but /after/ bpf_prog_put() from the remote CPU.
Therefore, move both notifications /before/ we install the fd. The
issue was never seen between bpf_prog_alloc_id() and bpf_prog_new_fd()
because upon bpf_prog_get_fd_by_id() we'll take another reference to
the BPF prog, so we're still holding the original reference from the
bpf_prog_load().
Fixes: 6ee52e2a3fe4 ("perf, bpf: Introduce PERF_RECORD_BPF_EVENT") Fixes: 74451e66d516 ("bpf: make jited programs visible in traces") Reported-by: syzbot+bd3bba6ff3fcea7a6ec6@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Song Liu <songliubraving@fb.com> Signed-off-by: Zubin Mithra <zsm@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a scenario causing ocfs2 umount hang when multiple hosts are
rebooting at the same time.
NODE1 NODE2 NODE3
send unlock requset to NODE2
dies
become recovery master
recover NODE2
find NODE2 dead
mark resource RECOVERING
directly remove lock from grant list
calculate usage but RECOVERING marked
**miss the window of purging
clear RECOVERING
To reproduce this issue, crash a host and then umount ocfs2
from another node.
To solve this, just let unlock progress wait for recovery done.
Link: http://lkml.kernel.org/r/1550124866-20367-1-git-send-email-gechangwei@live.cn Signed-off-by: Changwei Ge <gechangwei@live.cn> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 9e3596b0c653 ("kbuild: initramfs cleanup, set target from Kconfig")
"make clean" leaves behind compressed initramfs images. Example:
$ make defconfig
$ sed -i 's|CONFIG_INITRAMFS_SOURCE=""|CONFIG_INITRAMFS_SOURCE="/tmp/ir.cpio"|' .config
$ make olddefconfig
$ make -s
$ make -s clean
$ git clean -ndxf | grep initramfs
Would remove usr/initramfs_data.cpio.gz
clean rules do not have CONFIG_* context so they do not know which
compression format was used. Thus they don't know which files to delete.
Tell clean to delete all possible compression formats.
Once patched usr/initramfs_data.cpio.gz and friends are deleted by
"make clean".
Link: http://lkml.kernel.org/r/20190722063251.55541-1-gthelen@google.com Fixes: 9e3596b0c653 ("kbuild: initramfs cleanup, set target from Kconfig") Signed-off-by: Greg Thelen <gthelen@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In hypfs_fill_super(), if hypfs_create_update_file() fails,
sbi->update_file is left holding an error number. This is passed to
hypfs_kill_super() which doesn't check for this.
Fix this by not setting sbi->update_value until after we've checked for
error.
Fixes: 24bbb1faf3f0 ("[PATCH] s390_hypfs filesystem") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
cc: Heiko Carstens <heiko.carstens@de.ibm.com>
cc: linux-s390@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Anatoly reports that he gets the below warning when booting -git on
a sparc64 box on debian unstable:
...
[ 13.352975] aes_sparc64: Using sparc64 aes opcodes optimized AES
implementation
[ 13.428002] ------------[ cut here ]------------
[ 13.428081] WARNING: CPU: 21 PID: 586 at
drivers/block/pktcdvd.c:2597 pkt_setup_dev+0x2e4/0x5a0 [pktcdvd]
[ 13.428147] Attempt to register a non-SCSI queue
[ 13.428184] Modules linked in: pktcdvd libdes cdrom aes_sparc64
n2_rng md5_sparc64 sha512_sparc64 rng_core sha256_sparc64 flash
sha1_sparc64 ip_tables x_tables ipv6 crc_ccitt nf_defrag_ipv6 autofs4
ext4 crc16 mbcache jbd2 raid10 raid456 async_raid6_recov async_memcpy
async_pq async_xor xor async_tx raid6_pq raid1 raid0 multipath linear
md_mod crc32c_sparc64
[ 13.428452] CPU: 21 PID: 586 Comm: pktsetup Not tainted 5.3.0-10169-g574cc4539762 #1234
[ 13.428507] Call Trace:
[ 13.428542] [00000000004635c0] __warn+0xc0/0x100
[ 13.428582] [0000000000463634] warn_slowpath_fmt+0x34/0x60
[ 13.428626] [000000001045b244] pkt_setup_dev+0x2e4/0x5a0 [pktcdvd]
[ 13.428674] [000000001045ccf4] pkt_ctl_ioctl+0x94/0x220 [pktcdvd]
[ 13.428724] [00000000006b95c8] do_vfs_ioctl+0x628/0x6e0
[ 13.428764] [00000000006b96c8] ksys_ioctl+0x48/0x80
[ 13.428803] [00000000006b9714] sys_ioctl+0x14/0x40
[ 13.428847] [0000000000406294] linux_sparc_syscall+0x34/0x44
[ 13.428890] irq event stamp: 4181
[ 13.428924] hardirqs last enabled at (4189): [<00000000004e0a74>]
console_unlock+0x634/0x6c0
[ 13.428984] hardirqs last disabled at (4196): [<00000000004e0540>]
console_unlock+0x100/0x6c0
[ 13.429048] softirqs last enabled at (3978): [<0000000000b2e2d8>]
__do_softirq+0x498/0x520
[ 13.429110] softirqs last disabled at (3967): [<000000000042cfb4>]
do_softirq_own_stack+0x34/0x60
[ 13.429172] ---[ end trace 2220ca468f32967d ]---
[ 13.430018] pktcdvd: setup of pktcdvd device failed
[ 13.455589] des_sparc64: Using sparc64 des opcodes optimized DES
implementation
[ 13.515334] camellia_sparc64: Using sparc64 camellia opcodes
optimized CAMELLIA implementation
[ 13.522856] pktcdvd: setup of pktcdvd device failed
[ 13.529327] pktcdvd: setup of pktcdvd device failed
[ 13.532932] pktcdvd: setup of pktcdvd device failed
[ 13.536165] pktcdvd: setup of pktcdvd device failed
[ 13.539372] pktcdvd: setup of pktcdvd device failed
[ 13.542834] pktcdvd: setup of pktcdvd device failed
[ 13.546536] pktcdvd: setup of pktcdvd device failed
[ 15.431071] XFS (dm-0): Mounting V5 Filesystem
...
Apparently debian auto-attaches any cdrom like device to pktcdvd, which
can lead to the above warning. There's really no reason to warn for this
situation, kill it.
If userspace reads the buffer via blockdev while mounting,
sb_getblk()+modify can race with buffer read via blockdev.
For example,
FS userspace
bh = sb_getblk()
modify bh->b_data
read
ll_rw_block(bh)
fill bh->b_data by on-disk data
/* lost modified data by FS */
set_buffer_uptodate(bh)
set_buffer_uptodate(bh)
Userspace should not use the blockdev while mounting though, the udev
seems to be already doing this. Although I think the udev should try to
avoid this, workaround the race by small overhead.
Link: http://lkml.kernel.org/r/87pnk7l3sw.fsf_-_@mail.parknet.co.jp Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The calculation of memblock_limit in adjust_lowmem_bounds() assumes that
bank 0 starts from a PMD-aligned address. However, the beginning of the
first bank may be NOMAP memory and the start of usable memory
will be not aligned to PMD boundary. In such case the memblock_limit will
be set to the end of the NOMAP region, which will prevent any memblock
allocations.
Mark the region between the end of the NOMAP area and the next PMD-aligned
address as NOMAP as well, so that the usable memory will start at
PMD-aligned address.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_of_phy_get() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate devres structures. Propagating only -EPROBE_DEFER
is problematic because it results in these legitimately fatal errors
being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get() returns -ENODEV in this case, so
that's the special case that we need to handle. So we propagate all
errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Cc: Jingoo Han <jingoohan1@gmail.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: kernel@pengutronix.de Cc: linux-imx@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Shawn Lin <shawn.lin@rock-chips.com> Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: linux-rockchip@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes an issue in which key down events for function keys would be
repeatedly emitted even after the user has raised the physical key. For
example, the driver fails to emit the F5 key up event when going through
the following steps:
- fnmode=1: hold FN, hold F5, release FN, release F5
- fnmode=2: hold F5, hold FN, release F5, release FN
The repeated F5 key down events can be easily verified using xev.
Signed-off-by: Joao Moreno <mail@joaomoreno.com> Co-developed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Translation faults arising from cache maintenance instructions are
rather unhelpfully reported with an FSR value where the WnR field is set
to 1, indicating that the faulting access was a write. Since cache
maintenance instructions on 32-bit ARM do not require any particular
permissions, this can cause our private 'cacheflush' system call to fail
spuriously if a translation fault is generated due to page aging when
targetting a read-only VMA.
In this situation, we will return -EFAULT to userspace, although this is
unfortunately suppressed by the popular '__builtin___clear_cache()'
intrinsic provided by GCC, which returns void.
Although it's tempting to write this off as a userspace issue, we can
actually do a little bit better on CPUs that support LPAE, even if the
short-descriptor format is in use. On these CPUs, cache maintenance
faults additionally set the CM field in the FSR, which we can use to
suppress the write permission checks in the page fault handler and
succeed in performing cache maintenance to read-only areas even in the
presence of a translation fault.
Reported-by: Orion Hodson <oth@google.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
klp_module_coming() is called for every module appearing in the system.
It sets obj->mod to a patched module for klp_object obj. Unfortunately
it leaves it set even if an error happens later in the function and the
patched module is not allowed to be loaded.
klp_is_object_loaded() uses obj->mod variable and could currently give a
wrong return value. The bug is probably harmless as of now.
Signed-off-by: Miroslav Benes <mbenes@suse.cz> Reviewed-by: Petr Mladek <pmladek@suse.com> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each iteration of for_each_child_of_node() executes of_node_put() on the
previous node, but in some return paths in the middle of the loop
of_node_put() is missing thus causing a reference leak.
Hence stash these mid-loop return values in a variable 'err' and add a
new label err_node_put which executes of_node_put() on the previous node
and returns 'err' on failure.
Change mid-loop return statements to point to jump to this label to
fix the reference leak.
Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.
This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.
The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem is that the CHT Whiskey Cove PMIC's builtin i2c-adapter is
itself a part of an i2c-client (the PMIC). This means that transfers done
through it take adapter->bus_lock twice, once for the parent i2c-adapter
and once for its own bus_lock. Lockdep does not like this nested locking.
To make lockdep happy in the case of busses with muxes, the i2c-core's
i2c_adapter_lock_bus function calls:
But i2c_adapter_depth only works when the direct parent of the adapter is
another adapter, as it is only meant for muxes. In this case there is an
i2c-client and MFD instantiated platform_device in the parent->child chain
between the 2 devices.
This commit overrides the default i2c_lock_operations, passing a hardcoded
depth of 1 to rt_mutex_lock_nested, making lockdep happy.
Note that if there were to be a mux attached to the i2c-wc-cht adapter,
this would break things again since the i2c-mux code expects the
root-adapter to have a locking depth of 0. But the i2c-wc-cht adapter
always has only 1 client directly attached in the form of the charger IC
paired with the CHT Whiskey Cove PMIC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log