The return value of hga_card_detect() is not properly handled causing
the probe to succeed even though hga_card_detect() failed. Since probe
succeeds, hgafb_open() can be called which will end up operating on an
unmapped hga_vram. This results in an out-of-bounds access as reported
by kernel test robot [1].
To fix this, correctly detect failure of hga_card_detect() by checking
for a non-zero error code.
syzbot is reporting OOB write at vga16fb_imageblit() [1], for
resize_screen() from ioctl(VT_RESIZE) returns 0 without checking whether
requested rows/columns fit the amount of memory reserved for the graphical
screen if current mode is KD_GRAPHICS.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d0763361b ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e400b6ec4ede ("vt/vgacon: Check if screen resize request comes from userspace") Cc: stable@vger.kernel.org # v2.6.24+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qlcnic_dl_lb_test() currently calls netdev_alloc_skb()
without checking afterwards that the allocation succeeded. Fix this by
checking if the skb is NULL and returning an error in such a case.
Breaking out of the loop if the skb is NULL is not correct as no error
would be reported to the caller and no message would be printed for the
user.
Check return value of lp5xx_read and if non-zero, jump to code at end of
the function, causing lp5523_stop_all_engines to be executed before
returning the error value up the call chain. This fixes the original
commit (248b57015f35) which was reverted due to the University of Minnesota
problems.
If alloc_workqueue() fails, properly catch this and propagate the error
to the calling functions, so that the devuce initialization will
properly error out.
In case clk_prepare() fails, capture and propagate the error code up the
stack. If regulator_enable() was called earlier, properly unwind it by
calling regulator_disable().
niu_pci_eeprom_read() may fail, so add checks to its return value and
propagate the error up the callstack.
An examination of the callstack up to niu_pci_eeprom_read shows that:
niu_pci_eeprom_read() // returns int
niu_pci_vpd_scan_props() // returns int
niu_pci_vpd_fetch() // returns *void*
niu_get_invariants() // returns int
since niu_pci_vpd_fetch() returns void which breaks the bubbling up,
change its return type to int so that error is propagated upwards.
Signed-off-by: Du Cheng <ducheng2@gmail.com> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-24-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change here was incorrect. While it is nice to check if
niu_pci_eeprom_read() succeeded or not when using the data, any error
that might have happened was not propagated upwards properly, causing
the kernel to assume that these reads were successful, which results in
invalid data in the buffer that was to contain the successfully read
data.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Fixes: 26fd962bde0b ("niu: fix missing checks of niu_pci_eeprom_read") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-23-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit does not properly detect if an error happens because the
logic after this loop will not detect that there was a failed
allocation.
Cc: Aditya Pakki <pakki001@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: 5bf7295fe34a ("qlcnic: Avoid potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-25-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Bryan Brattlof <hello@bryanbrattlof.com> Fixes: 765976285a8c ("rtlwifi: fix a potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all as
the media core already prevents memory disclosure on this codepath, so
just drop the extra memset happening here.
As Peter points out, if we were to disconnect and then reconnect this
driver from a device, the "global" state of the device would contain odd
values and could cause problems. Fix this up by just initializing the
whole thing to 0 at probe() time.
Ideally this would be a per-device variable, but given the age and the
total lack of users of it, that would require a lot of s/./->/g changes
for really no good reason.
Reported-by: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Reviewed-by: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/YJP2j6AU82MqEY2M@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fields, "toc" and "cd_info", of "struct gdrom_unit gd" are allocated
in "probe_gdrom()". Prevent a memory leak by making sure "gd.cd_info" is
deallocated in the "remove_gdrom()" function.
Also prevent double free of the field "gd.toc" by moving it from the
module's exit function to "remove_gdrom()". This is because, in
"probe_gdrom()", the function makes sure to deallocate "gd.toc" in case
of any errors, so the exit function invoked later would again free
"gd.toc".
The patch also maintains consistency by deallocating the above mentioned
fields in "remove_gdrom()" along with another memory allocated field
"gd.disk".
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Because of this, all submissions from this group must be reverted from
the kernel tree and will need to be re-reviewed again to determine if
they actually are a valid fix. Until that work is complete, remove this
change to ensure that no problems are being introduced into the
codebase.
Cc: Wenwen Wang <wang6495@umn.edu> Cc: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Fixes: 093c48213ee3 ("gdrom: fix a memory leak bug") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-27-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit log for this change was incorrect, no "error
handling code" was added, things will blow up just as badly as before if
any of these cases ever were true. As this BUG_ON() never fired, and
most of these checks are "obviously" never going to be true, let's just
revert to the original code for now until this gets unwound to be done
correctly in the future.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here, while technically correct, did not fully
handle all of the reported issues that the commit stated it was fixing,
so revert it until it can be "fixed" fully.
Note, ioremap() probably will never fail for old hardware like this, and
if anyone actually used this hardware (a PowerMac era PCI display card),
they would not be using fbdev anymore.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu> Fixes: 9aa3aa15f4c2 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe") Cc: stable <stable@vger.kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit does not properly unwind if there is an error
condition so it needs to be reverted at this point in time.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: stable <stable@vger.kernel.org> Fixes: 248b57015f35 ("leds: lp5523: fix a missing check of return value of lp55xx_read") Link: https://lore.kernel.org/r/20210503115736.2104747-9-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: f86a3b83833e ("net: stmicro: fix a missing check of clk_prepare") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This patch "looks" correct, but the driver keeps on running and will
fail horribly right afterward if this error condition ever trips.
So points for trying to resolve an issue, but a huge NEGATIVE value for
providing a "fake" fix for the problem as nothing actually got resolved
at all. I'll go fix this up properly...
modprobe brd rd_size=1048576
dmsetup create o --table "0 `blockdev --getsize /dev/ram0` snapshot-origin /dev/ram0"
dmsetup create s --table "0 `blockdev --getsize /dev/ram0` snapshot /dev/ram0 /dev/ram1 N 0"
The reason is that when we test for zero chunk size, we jump to the label
bad_read_metadata without setting the "r" variable. The function
snapshot_ctr destroys all the structures and then exits with "r == 0". The
kernel then crashes because it falsely believes that snapshot_ctr
succeeded.
In order to fix the bug, we set the variable "r" to -EINVAL.
When multiple PCI devices get assigned to a guest right at boot, libxl
incrementally populates the backend tree. The writes for the first of
the devices trigger the backend watch. In turn xen_pcibk_setup_backend()
will set the XenBus state to Initialised, at which point no further
reconfigures would happen unless a device got hotplugged. Arrange for
reconfigure to also get triggered from the backend watch handler.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: stable@vger.kernel.org Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/2337cbd6-94b9-4187-9862-c03ea12e0c61@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case create_workqueue() fails, release all resources and return -ENOMEM
to caller to avoid potential NULL pointer deref later. Move up the
create_workequeue() call to return early and avoid unwinding the call to
riocm_rx_fill().
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit has a memory leak on the error path here, it does
not clean up everything properly.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Fixes: 23015b22e47c ("rapidio: fix a NULL pointer dereference when create_workqueue() fails") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-45-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ubuntu users reported an audio bug on the Lenovo Yoga Slim 7 14IIL05,
he installed dual OS (Windows + Linux), if he booted to the Linux
from Windows, the Speaker can't work well, it has crackling noise,
if he poweroff the machine first after Windows, the Speaker worked
well.
Before rebooting or shutdown from Windows, the Windows changes the
codec eapd coeff value, but the BIOS doesn't re-initialize its value,
when booting into the Linux from Windows, the eapd coeff value is not
correct. To fix it, set the codec default value to that coeff register
in the alsa driver.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit message for this change was incorrect as the code
path can never result in a NULL dereference, alluding to the fact that
whatever tool was used to "find this" is broken. It's just an optional
resource reservation, so removing this check is fine.
Cc: Kangjie Lu <kjlu@umn.edu> Acked-by: Takashi Iwai <tiwai@suse.de> Fixes: dcd0feac9bab ("ALSA: sb8: add a check for request_region") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-35-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mackie d.2 has an extension card for IEEE 1394 communication, which uses
BridgeCo DM1000 ASIC. On the other hand, Mackie d.4 Pro has built-in
function for IEEE 1394 communication by Oxford Semiconductor OXFW971,
according to schematic diagram available in Mackie website. Although I
misunderstood that Mackie d.2 Pro would be also a model with OXFW971,
it's wrong. Mackie d.2 Pro is a model which includes the extension card
as factory settings.
This commit fixes entries in Kconfig and comment in ALSA OXFW driver.
Cc: <stable@vger.kernel.org> Fixes: fd6f4b0dc167 ("ALSA: bebob: Add skelton for BeBoB based devices") Fixes: ec4dba5053e1 ("ALSA: oxfw: Add support for Behringer/Mackie devices") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20210513125652.110249-3-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usbmidi_get_ms_info() may access beyond the border when a
malformed descriptor is passed. This patch adds the sanity checks of
the given MS endpoint descriptors, and skips invalid ones.
The initialization of MIDI devices that are found on some LINE6
drivers are currently done in a racy way; namely, the MIDI buffer
instance is allocated and initialized in each private_init callback
while the communication with the interface is already started via
line6_init_cap_control() call before that point. This may lead to
Oops in line6_data_received() when a spurious event is received, as
reported by syzkaller.
This patch moves the MIDI initialization to line6_init_cap_control()
as well instead of the too-lately-called private_init for avoiding the
race. Also this reduces slightly more lines, so it's a win-win
change.
When using smb2_copychunk_range() for large ranges we will
run through several iterations of a loop calling SMB2_ioctl()
but never actually free the returned buffer except for the final
iteration.
This leads to memory leaks everytime a large copychunk is requested.
Fixes: 9bf0c9cd4314 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files") Cc: <stable@vger.kernel.org> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we have 2 threads, the group-leader L and a sub-theread T,
both parked in ptrace_stop(). Debugger tries to resume both threads
and does
ptrace(PTRACE_CONT, T);
ptrace(PTRACE_CONT, L);
If the sub-thread T execs in between, the 2nd PTRACE_CONT doesn not
resume the old leader L, it resumes the post-exec thread T which was
actually now stopped in PTHREAD_EVENT_EXEC. In this case the
PTHREAD_EVENT_EXEC event is lost, and the tracer can't know that the
tracee changed its pid.
This patch makes ptrace() fail in this case until debugger does wait()
and consumes PTHREAD_EVENT_EXEC which reports old_pid. This affects all
ptrace requests except the "asynchronous" PTRACE_INTERRUPT/KILL.
The patch doesn't add the new PTRACE_ option to not complicate the API,
and I _hope_ this won't cause any noticeable regression:
- If debugger uses PTRACE_O_TRACEEXEC and the thread did an exec
and the tracer does a ptrace request without having consumed
the exec event, it's 100% sure that the thread the ptracer
thinks it is targeting does not exist anymore, or isn't the
same as the one it thinks it is targeting.
- To some degree this patch adds nothing new. In the scenario
above ptrace(L) can fail with -ESRCH if it is called after the
execing sub-thread wakes the leader up and before it "steals"
the leader's pid.
rxe_qp_do_cleanup() relies on valid pointer values in QP for the properly
created ones, but in case rxe_qp_from_init() failed it was filled with
garbage and caused tot the following error.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
[iwamatsu: Adjust context] Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same reasons than for the previous commits : 6289a98f0817 ("sit: proper dev_{hold|put} in ndo_[un]init methods") 40cb881b5aaa ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods") 7f700334be9a ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
In RT system, the spin_lock will be replaced by sleepable rt_mutex lock,
in __call_rcu(), disable interrupts before calling
kasan_record_aux_stack(), will trigger this calltrace:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:951
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 19, name: pgdatinit0
Call Trace:
___might_sleep.cold+0x1b2/0x1f1
rt_spin_lock+0x3b/0xb0
stack_depot_save+0x1b9/0x440
kasan_save_stack+0x32/0x40
kasan_record_aux_stack+0xa5/0xb0
__call_rcu+0x117/0x880
__exit_signal+0xafb/0x1180
release_task+0x1d6/0x480
exit_notify+0x303/0x750
do_exit+0x678/0xcf0
kthread+0x364/0x4f0
ret_from_fork+0x22/0x30
Replace spinlock with raw_spinlock.
Link: https://lkml.kernel.org/r/20210329084009.27013-1-qiang.zhang@windriver.com Signed-off-by: Zqiang <qiang.zhang@windriver.com> Reported-by: Andrew Halaney <ahalaney@redhat.com> Cc: Alexander Potapenko <glider@google.com> Cc: Gustavo A. R. Silva <gustavoars@kernel.org> Cc: Vijayanand Jitta <vjitta@codeaurora.org> Cc: Vinayak Menon <vinmenon@codeaurora.org> Cc: Yogesh Lal <ylal@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
blkdev_read_iter can truncate iov_iter's count since the count + pos may
exceed the size of the blkdev. This will confuse io_read that we have
consume the iovec. And once we do the iov_iter_revert in io_read, we
will trigger the slab-out-of-bounds. Fix it by reexpand the count with
size has been truncated.
Without this change, the DAC ctl's name could be changed only when
the machine has both Speaker and Headphone, but we met some machines
which only has Lineout and Headhpone, and the Lineout and Headphone
share the Audio Mixer0 and DAC0, the ctl's name is set to "Front".
On most of machines, the "Front" is used for Speaker only or Lineout
only, but on this machine it is shared by Lineout and Headphone,
This introduces an issue in the pipewire and pulseaudio, suppose users
want the Headphone to be on and the Speaker/Lineout to be off, they
could turn off the "Front", this works on most of the machines, but on
this machine, the "Front" couldn't be turned off otherwise the
headphone will be off too. Here we do some change to let the ctl's
name change to "Headphone+LO" on this machine, and pipewire and
pulseaudio already could handle "Headphone+LO" and "Speaker+LO".
(https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/747)
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ritesh reported a bug [1] against UML, noting that it crashed on
startup. The backtrace shows the following (heavily redacted):
(gdb) bt
...
#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268
#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2
#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72
...
#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359
...
#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486
#45 0x00007f8990968b85 in __getgrnam_r [...]
#46 0x00007f89909d6b77 in grantpt [...]
#47 0x00007f8990a9394e in __GI_openpty [...]
#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407
#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598
#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45
#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334
#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144
indicating that the UML function openpty_cb() calls openpty(),
which internally calls __getgrnam_r(), which causes the nsswitch
machinery to get started.
This loads, through lots of indirection that I snipped, the
libcom_err.so.2 library, which (in an unknown function, "??")
calls sem_init().
Now, of course it wants to get libpthread's sem_init(), since
it's linked against libpthread. However, the dynamic linker
looks up that symbol against the binary first, and gets the
kernel's sem_init().
Hajime Tazaki noted that "objcopy -L" can localize a symbol,
so the dynamic linker wouldn't do the lookup this way. I tried,
but for some reason that didn't seem to work.
Doing the same thing in the linker script instead does seem to
work, though I cannot entirely explain - it *also* works if I
just add "VERSION { { global: *; }; }" instead, indicating that
something else is happening that I don't really understand. It
may be that explicitly doing that marks them with some kind of
empty version, and that's different from the default.
Explicitly marking them with a version breaks kallsyms, so that
doesn't seem to be possible.
Marking all the symbols as local seems correct, and does seem
to address the issue, so do that. Also do it for static link,
nsswitch libraries could still be loaded there.
[1] https://bugs.debian.org/983379
Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com Signed-off-by: Feilong Lin <linfeilong@huawei.com> Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enabling function_graph tracer on ARM causes kernel panic, because the
function graph tracer updates the "return address" of a function in order
to insert a trace callback on function exit, it saves the function's
original return address in a return trace stack, but cpu_suspend() may not
return through the normal return path.
cpu_suspend() will resume directly via the cpu_resume path, but the return
trace stack has been set-up by the subfunctions of cpu_suspend(), which
makes the "return address" inconsistent with cpu_suspend().
fixes the issue by pausing/resuming the function graph tracer on the thread
executing cpu_suspend(), so that the function graph tracer state is kept
consistent across functions that enter power down states and never return
by effectively disabling graph tracer while they are executing.
Signed-off-by: louis.wang <liang26812@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
gcc-11 complains about a prototype declaration that is different
from the function definition:
drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}
62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}
64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~
Change the definition to make them match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names") Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)
Because their data pointers are not updated to point to per-netns
structures, they must be marked read-only in a non-init_net ns.
Otherwise, changes in any net namespace are reflected in (leaked into)
all other net namespaces. This problem has existed since the
introduction of net namespaces.
The current logic marks them read-only only if the net namespace is
owned by an unprivileged user (other than init_user_ns).
Commit d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in
unprivileged namespaces") "exposes all sysctls even if the namespace is
unpriviliged." Since we need to mark them readonly in any case, we can
forego the unprivileged user check altogether.
Fixes: d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces") Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
The current code sets an affinity hint with a cpumask_t stored on the
stack. This value can then be accessed through /proc/irq/*/affinity_hint/,
causing a segfault or returning corrupt data.
Move the cpumask_t into struct i40iw_msix_vector so it is available later.
The tz->lock must be hold during the looping over the instances in that
thermal zone. This lock was missing in the governor code since the
beginning, so it's hard to point into a particular commit.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210422153624.6074-2-lukasz.luba@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b4c
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.") Reported-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems. It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support. However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.
Make DEFXX_MMIO the configuration default then, except where configured
for EISA. This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core. Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.
The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.
Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e89a2cfb7d7b ("[TC] defxx: TURBOchannel support") Cc: stable@vger.kernel.org # v2.6.21+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201 Reported-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Fixes: 0d2602ca30e4 ("blk-mq: improve support for shared tags maps") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'acpi_device_set_name()' fails, we must free
'acpi_device_bus_id->bus_id' or there is a (potential) memory leak.
Fixes: eb50aaf960e3 ("ACPI: scan: Use unique number for instance_no") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue
doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and
another one is 4K 30Hz (pixelclock 297MHz).
The issue is gone after setting "power_dpm_force_performance_level" to
"high". Following the indication, we found that the issue occurs when
sclk is too low.
So resolve the issue by disabling sclk switching when there are two
monitors requires high pixelclock (> 297MHz).
v2:
- Only apply the fix to Oland. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Userspace issues a UFFD ioctl, which ends up calling into
shmem_mfill_atomic_pte(). We successfully account the blocks, we
shmem_alloc_page(), but then the copy_from_user() fails. We return
-ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after
dropping the mmap_lock, and retries, calling back into
shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and
immediately returns - without releasing the page.
This triggers a BUG_ON in our caller, which asserts that the page
should always be consumed, unless -ENOENT is returned.
To fix this, detect if we have such a "dangling" page when accounting
fails, and if so, release it before returning.
Link: https://lkml.kernel.org/r/20210428230858.348400-1-axelrasmussen@google.com Fixes: cb658a453b93 ("userfaultfd: shmem: avoid leaking blocks and used blocks in UFFDIO_COPY") Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reported-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sysbot has reported a "divide error" which has been identified as being
caused by a corrupted file_size value within the file inode. This value
has been corrupted to a much larger value than expected.
Calculate_skip() is passed i_size_read(inode) >> msblk->block_log. Due to
the file_size value corruption this overflows the int argument/variable in
that function, leading to the divide error.
This patch changes the function to use u64. This will accommodate any
unexpectedly large values due to corruption.
The value returned from calculate_skip() is clamped to be never more than
SQUASHFS_CACHED_BLKS - 1, or 7. So file_size corruption does not lead to
an unexpectedly large return result here.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
When vzalloc() returns NULL to sha_regions, no error return code of
kexec_calculate_store_digests() is assigned. To fix this bug, ret is
assigned with -ENOMEM in this case.
Link: https://lkml.kernel.org/r/20210309083904.24321-1-baijiaju1990@gmail.com Fixes: a43cac0d9dc2 ("kexec: split kexec_file syscall code to kexec_file.c") Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Acked-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Android userspace has been using TCA_KIND with a char[IFNAMESIZ]
many-null-terminated buffer containing the string 'bpf'.
This works on 4.19 and ceases to work on 5.10.
I'm not entirely sure what fixes tag to use, but I think the issue
was likely introduced in the below mentioned 5.4 commit.
Reported-by: Nucca Chen <nuccachen@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: David Ahern <dsahern@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@mellanox.com> Cc: Jiri Pirko <jiri@resnulli.us> Fixes: 62794fc4fbf5 ("net_sched: add max len check for TCA_KIND")
Change-Id: I66dc281f165a2858fc29a44869a270a2d698a82b Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing rmap_item from stable tree, STABLE_FLAG of rmap_item is
cleared with head reserved. So the following scenario might happen: For
ksm page with rmap_item1:
cmp_and_merge_page
stable_node->head = &migrate_nodes;
remove_rmap_item_from_tree, but head still equal to stable_node;
try_to_merge_with_ksm_page failed;
return;
For the same ksm page with rmap_item2, stable node migration succeed this
time. The stable_node->head does not equal to migrate_nodes now. For ksm
page with rmap_item1 again:
We would miss the rmap_item for stable_node and might result in failed
rmap_walk_ksm(). Fix this by set rmap_item->head to NULL when rmap_item
is removed from stable tree.
Link: https://lkml.kernel.org/r/20210330140228.45635-5-linmiaohe@huawei.com Fixes: 4146d2d673e8 ("ksm: make !merge_across_nodes migration safe") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A rare out of memory error would prevent removal of the reserve map region
for a page. hugetlb_fix_reserve_counts() handles this rare case to avoid
dangling with incorrect counts. Unfortunately, hugepage_subpool_get_pages
and hugetlb_acct_memory could possibly fail too. We should correctly
handle these cases.
Link: https://lkml.kernel.org/r/20210410072348.20437-5-linmiaohe@huawei.com Fixes: b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Feilong Lin <linfeilong@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In writable and !referenced case, the result value should be
SCAN_LACK_REFERENCED_PAGE for trace_mm_collapse_huge_page_isolate()
instead of default 0 (SCAN_FAIL) here.
Link: https://lkml.kernel.org/r/20210306032947.35921-5-linmiaohe@huawei.com Fixes: 7d2eba0557c1 ("mm: add tracepoint for scanning pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An out of bounds write happens when setting the default power state.
KASAN sees this as:
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
==================================================================
BUG: KASAN: slab-out-of-bounds in
radeon_atombios_parse_power_table_1_3+0x1837/0x1998 [radeon]
Write of size 4 at addr ffff88810178d858 by task systemd-udevd/157
Without KASAN, this will manifest later when the kernel attempts to
allocate memory that was stomped, since it collides with the inline slab
freelist pointer:
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the client ignores the value of the sr_eof of the SEEK
operation. According to the spec, if the server didn't find the
requested extent and reached the end of the file, the server
would return sr_eof=true. In case the request for DATA and no
data was found (ie in the middle of the hole), then the lseek
expects that ENXIO would be returned.
We (adam zabrocki, alexander matrosov, alexander tereshkin, maksym
bazalii) observed the check:
if (fh->size > sizeof(struct nfs_fh))
should not use the size of the nfs_fh struct which includes an extra two
bytes from the size field.
struct nfs_fh {
unsigned short size;
unsigned char data[NFS_MAXFHSIZE];
}
but should determine the size from data[NFS_MAXFHSIZE] so the memcpy
will not write 2 bytes beyond destination. The proposed fix is to
compare against the NFS_MAXFHSIZE directly, as is done elsewhere in fs
code base.
Fixes: d67ae825a59d ("pnfs/flexfiles: Add the FlexFile Layout Driver") Signed-off-by: Nikola Livic <nlivic@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to use unsigned long subtraction and then convert to signed in
order to deal correcly with C overflow rules.
Fixes: f5062003465c ("NFS: Set an attribute barrier on all updates") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>