Jan Beulich [Tue, 18 May 2021 16:13:42 +0000 (18:13 +0200)]
xen-pciback: redo VF placement in the virtual topology
The commit referenced below was incomplete: It merely affected what
would get written to the vdev-<N> xenstore node. The guest would still
find the function at the original function number as long as
__xen_pcibk_get_pci_dev() wouldn't be in sync. The same goes for AER wrt
__xen_pcibk_get_pcifront_dev().
Undo overriding the function to zero and instead make sure that VFs at
function zero remain alone in their slot. This has the added benefit of
improving overall capacity, considering that there's only a total of 32
slots available right now (PCI segment and bus can both only ever be
zero at present).
select_idle_cpu() will scan the LLC domain for idle CPUs,
it's always expensive. so the next commit :
1ad3aaf3fcd2 ("sched/core: Implement new approach to scale select_idle_cpu()")
introduces a way to limit how many CPUs we scan.
But it consume some CPUs out of 'nr' that are not allowed
for the task and thus waste our attempts. The function
always return nr_cpumask_bits, and we can't find a CPU
which our task is allowed to run.
Cpumask may be too big, similar to select_idle_core(), use
per_cpu_ptr 'select_idle_mask' to prevent stack overflow.
Fixes: 1ad3aaf3fcd2 ("sched/core: Implement new approach to scale select_idle_cpu()") Signed-off-by: Cheng Jian <cj.chengjian@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lkml.kernel.org/r/20191213024530.28052-1-cj.chengjian@huawei.com Signed-off-by: Yang Wei <yang.wei@linux.alibaba.com> Tested-by: Yang Wei <yang.wei@linux.alibaba.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop bits 63:32 on loads/stores to/from DRs and CRs when the vCPU is not
in 64-bit mode. The APM states bits 63:32 are dropped for both DRs and
CRs:
In 64-bit mode, the operand size is fixed at 64 bits without the need
for a REX prefix. In non-64-bit mode, the operand size is fixed at 32
bits and the upper 32 bits of the destination are forced to 0.
Fixes: 7ff76d58a9dc ("KVM: SVM: enhance MOV CR intercept handler") Fixes: cae3797a4639 ("KVM: SVM: enhance mov DR intercept handler") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422022128.3464144-4-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sudip: manual backport to old file] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_port is meant to distinguish the network ports belonging to
the same PCI function. Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 801c6058d14a ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.
Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.
Fixes: 7fedb63a8307 ("bpf: Tighten speculative pointer arithmetic mask") Reported-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implemented mechanisms to mitigate data disclosure under
speculation mainly address stack and map value oob access from the
speculative domain. However, Piotr discovered that uninitialized BPF
stack is not protected yet, and thus old data from the kernel stack,
potentially including addresses of kernel structures, could still be
extracted from that 512 bytes large window. The BPF stack is special
compared to map values since it's not zero initialized for every
program invocation, whereas map values /are/ zero initialized upon
their initial allocation and thus cannot leak any prior data in either
domain. In the non-speculative domain, the verifier ensures that every
stack slot read must have a prior stack slot write by the BPF program
to avoid such data leaking issue.
However, this is not enough: for example, when the pointer arithmetic
operation moves the stack pointer from the last valid stack offset to
the first valid offset, the sanitation logic allows for any intermediate
offsets during speculative execution, which could then be used to
extract any restricted stack content via side-channel.
Given for unprivileged stack pointer arithmetic the use of unknown
but bounded scalars is generally forbidden, we can simply turn the
register-based arithmetic operation into an immediate-based arithmetic
operation without the need for masking. This also gives the benefit
of reducing the needed instructions for the operation. Given after
the work in 7fedb63a8307 ("bpf: Tighten speculative pointer arithmetic
mask"), the aux->alu_limit already holds the final immediate value for
the offset register with the known scalar. Thus, a simple mov of the
immediate to AX register with using AX as the source for the original
instruction is sufficient and possible now in this case.
Reported-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Piotr Krysiuk <piotras@gmail.com> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: fixed minor 4.14 conflict because of renamed function] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly revert the previous workaround and make
'dubious pointer arithmetic' test useful again.
Use (ptr - ptr) << const instead of ptr << const to generate large scalar.
The rest stays as before commit 2b36047e7889.
Fixes: 2b36047e7889 ("selftests/bpf: fix test_align") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[fllinden@amazon.com: adjust for 4.14 (no liveness of regs in output)] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit 82abbf8d2fc4 the verifier rejects the bit-wise
arithmetic on pointers earlier.
The test 'dubious pointer arithmetic' now has less output to match on.
Adjust it.
Fixes: 82abbf8d2fc4 ("bpf: do not allow root to mangle valid pointers") Reported-by: kernel test robot <xiaolong.ye@intel.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subtraction of pointers was accidentally allowed for unpriv programs
by commit 82abbf8d2fc4. Revert that part of commit.
Fixes: 82abbf8d2fc4 ("bpf: do not allow root to mangle valid pointers") Reported-by: Jann Horn <jannh@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[fllinden@amazon.com: backport to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not allow root to convert valid pointers into unknown scalars.
In particular disallow:
ptr &= reg
ptr <<= reg
ptr += ptr
and explicitly allow:
ptr -= ptr
since pkt_end - pkt == length
1.
This minimizes amount of address leaks root can do.
In the future may need to further tighten the leaks with kptr_restrict.
2.
If program has such pointer math it's likely a user mistake and
when verifier complains about it right away instead of many instructions
later on invalid memory access it's easier for users to fix their progs.
3.
when register holding a pointer cannot change to scalar it allows JITs to
optimize better. Like 32-bit archs could use single register for pointers
instead of a pair required to hold 64-bit scalars.
4.
reduces architecture dependent behavior. Since code:
r1 = r10;
r1 &= 0xff;
if (r1 ...)
will behave differently arm64 vs x64 and offloaded vs native.
A significant chunk of ptr mangling was allowed by
commit f1174f77b50c ("bpf/verifier: rework value tracking")
yet some of it was allowed even earlier.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[fllinden@amazon.com: backport to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* The 'Rx tried to sub from different maps, paths, or prohibited types'
is reworked into more specific/differentiated error messages for better
guidance.
* The change into 'value -4294967168 makes map_value pointer be out of
bounds' is due to moving the mixed bounds check into the speculation
handling and thus occuring slightly later than above mentioned sanity
check.
* The change into 'math between map_value pointer and register with
unbounded min value' is similarly due to register sanity check coming
before the mixed bounds check.
* The case of 'map access: known scalar += value_ptr from different maps'
now loads fine given masks are the same from the different paths (despite
max map value size being different).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com - 4.14 backport, account for split test_verifier and
different / missing tests] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This work tightens the offset mask we use for unprivileged pointer arithmetic
in order to mitigate a corner case reported by Piotr and Benedict where in
the speculative domain it is possible to advance, for example, the map value
pointer by up to value_size-1 out-of-bounds in order to leak kernel memory
via side-channel to user space.
Before this change, the computed ptr_limit for retrieve_ptr_limit() helper
represents largest valid distance when moving pointer to the right or left
which is then fed as aux->alu_limit to generate masking instructions against
the offset register. After the change, the derived aux->alu_limit represents
the largest potential value of the offset register which we mask against which
is just a narrower subset of the former limit.
For minimal complexity, we call sanitize_ptr_alu() from 2 observation points
in adjust_ptr_min_max_vals(), that is, before and after the simulated alu
operation. In the first step, we retieve the alu_state and alu_limit before
the operation as well as we branch-off a verifier path and push it to the
verification stack as we did before which checks the dst_reg under truncation,
in other words, when the speculative domain would attempt to move the pointer
out-of-bounds.
In the second step, we retrieve the new alu_limit and calculate the absolute
distance between both. Moreover, we commit the alu_state and final alu_limit
via update_alu_sanitation_state() to the env's instruction aux data, and bail
out from there if there is a mismatch due to coming from different verification
paths with different states.
Reported-by: Piotr Krysiuk <piotras@gmail.com> Reported-by: Benedict Schlueter <benedict.schlueter@rub.de> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Benedict Schlueter <benedict.schlueter@rub.de>
[fllinden@amazon.com: backported to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a small sanitize_needed() helper function and move sanitize_val_alu()
out of the main opcode switch. In upcoming work, we'll move sanitize_ptr_alu()
as well out of its opcode switch so this helps to streamline both.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backported to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bounds check in adjust_ptr_min_max_vals() into a small helper named
sanitize_check_bounds() in order to simplify the former a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consolidate all error handling and provide more user-friendly error messages
from sanitize_ptr_alu() and sanitize_val_alu().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mixed signed bounds check really belongs into retrieve_ptr_limit()
instead of outside of it in adjust_ptr_min_max_vals(). The reason is
that this check is not tied to PTR_TO_MAP_VALUE only, but to all pointer
types that we handle in retrieve_ptr_limit() and given errors from the latter
propagate back to adjust_ptr_min_max_vals() and lead to rejection of the
program, it's a better place to reside to avoid anything slipping through
for future types. The reason why we must reject such off_reg is that we
otherwise would not be able to derive a mask, see details in 9d7eceede769
("bpf: restrict unknown scalars of mixed signed bounds for unprivileged").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Small refactor to drag off_reg into sanitize_ptr_alu(), so we later on can
use off_reg for generalizing some of the checks for all pointer types.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: fix minor contextual conflict for 4.14] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up test_verifier error messages for the case where the original error
message changed, or for the case where pointer alu errors differ between
privileged and unprivileged tests. Also, add alternative tests for keeping
coverage of the original verifier rejection error message (fp alu), and
newly reject map_ptr += rX where rX == 0 given we now forbid alu on these
types for unprivileged. All test_verifier cases pass after the change. The
test case fixups were kept separate to ease backporting of core changes.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com> Co-developed-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 4.14, skipping non-existent tests] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The userfaultfd hugetlb tests cause a resv_huge_pages underflow. This
happens when hugetlb_mcopy_atomic_pte() is called with !is_continue on
an index for which we already have a page in the cache. When this
happens, we allocate a second page, double consuming the reservation,
and then fail to insert the page into the cache and return -EEXIST.
To fix this, we first check if there is a page in the cache which
already consumed the reservation, and return -EEXIST immediately if so.
There is still a rare condition where we fail to copy the page contents
AND race with a call for hugetlb_no_page() for this index and again we
will underflow resv_huge_pages. That is fixed in a more complicated
patch not targeted for -stable.
Test:
Hacked the code locally such that resv_huge_pages underflows produce a
warning, then:
./tools/testing/selftests/vm/userfaultfd hugetlb_shared 10
2 /tmp/kokonut_test/huge/userfaultfd_test && echo test success
./tools/testing/selftests/vm/userfaultfd hugetlb 10
2 /tmp/kokonut_test/huge/userfaultfd_test && echo test success
Both tests succeed and produce no warnings. After the test runs number
of free/resv hugepages is correct.
[mike.kravetz@oracle.com: changelog fixes]
Link: https://lkml.kernel.org/r/20210528004649.85298-1-almasrymina@google.com Fixes: 8fb5debc5fcd ("userfaultfd: hugetlbfs: add hugetlb_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Mina Almasry <almasrymina@google.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
while (1) {
ret = whatever();
if (ret)
goto out;
}
ret = 0
out:
return ret;
However several places in this while loop we simply break; when there's
a problem, thus clearing the return value, and in one case we do a
return -EIO, and leak the memory for the path.
Fix this by re-arranging the loop to deal with ret == 1 coming from
btrfs_search_slot, and then simply delete the
ret = 0;
out:
bit so everybody can break if there is an error, which will allow for
proper error handling to occur.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error injection stress would sometimes fail with checksums on disk that
did not have a corresponding extent. This occurred because the pattern
in btrfs_del_csums was
while (1) {
ret = btrfs_search_slot();
if (ret < 0)
break;
}
ret = 0;
out:
btrfs_free_path(path);
return ret;
If we got an error from btrfs_search_slot we'd clear the error because
we were breaking instead of goto out. Instead of using goto out, simply
handle the cases where we may leave a random value in ret, and get rid
of the
ret = 0;
out:
pattern and simply allow break to have the proper error reporting. With
this fix we properly abort the transaction and do not commit thinking we
successfully deleted the csum.
Reviewed-by: Qu Wenruo <wqu@suse.com> CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to trigger NULL pointer dereference by local unprivileged
user, when calling getsockname() after failed bind() (e.g. the bind
fails because LLCP_SAP_MAX used as SAP):
When fallocate punches holes out of inode size, if original isize is in
the middle of last cluster, then the part from isize to the end of the
cluster will be zeroed with buffer write, at that time isize is not yet
updated to match the new size, if writeback is kicked in, it will invoke
ocfs2_writepage()->block_write_full_page() where the pages out of inode
size will be dropped. That will cause file corruption. Fix this by
zero out eof blocks when extending the inode size.
Running the following command with qemu-image 4.2.1 can get a corrupted
coverted image file easily.
Link: https://lkml.kernel.org/r/20210528210648.9124-1-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Jan Kara <jack@suse.cz> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During boot, kernel_init_freeable() initializes `cad_pid` to the init
task's struct pid. Later on, we may change `cad_pid` via a sysctl, and
when this happens proc_do_cad_pid() will increment the refcount on the
new pid via get_pid(), and will decrement the refcount on the old pid
via put_pid(). As we never called get_pid() when we initialized
`cad_pid`, we decrement a reference we never incremented, can therefore
free the init task's struct pid early. As there can be dangling
references to the struct pid, we can later encounter a use-after-free
(e.g. when delivering signals).
This was spotted when fuzzing v5.13-rc3 with Syzkaller, but seems to
have been around since the conversion of `cad_pid` to struct pid in
commit 9ec52099e4b8 ("[PATCH] replace cad_pid by a struct pid") from the
pre-KASAN stone age of v2.6.19.
Fix this by getting a reference to the init task's struct pid when we
assign it to `cad_pid`.
Full KASAN splat below.
==================================================================
BUG: KASAN: use-after-free in ns_of_pid include/linux/pid.h:153 [inline]
BUG: KASAN: use-after-free in task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509
Read of size 4 at addr ffff23794dda0004 by task syz-executor.0/273
Memory state around the buggy address: ffff23794dd9ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff23794dd9ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff23794dda0000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff23794dda0080: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc ffff23794dda0100: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Link: https://lkml.kernel.org/r/20210524172230.38715-1-mark.rutland@arm.com Fixes: 9ec52099e4b8678a ("[PATCH] replace cad_pid by a struct pid") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: Christian Brauner <christian@brauner.io> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Kees Cook <keescook@chromium.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch's modification is according to Jan Kara's suggestion in:
https://patchwork.ozlabs.org/project/linux-ext4/patch/20210428085158.3728201-1-yebin10@huawei.com/
"I see. Now I understand your patch. Honestly, seeing how fragile is trying
to fix extent tree after split has failed in the middle, I would probably
go even further and make sure we fix the tree properly in case of ENOSPC
and EDQUOT (those are easily user triggerable). Anything else indicates a
HW problem or fs corruption so I'd rather leave the extent tree as is and
don't try to fix it (which also means we will not create overlapping
extents)."
Cc: stable@kernel.org Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210506141042.3298679-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_timer_notify1() calls the notification to each slave for a master
event, but it passes a wrong event number. It should be +10 offset,
corresponding to SNDRV_TIMER_EVENT_MXXX, but it's incorrectly with
+100 offset. Casually this was spotted by UBSAN check via syzkaller.
In case of caif_enroll_dev() fail, allocated
link_support won't be assigned to the corresponding
structure. So simply free allocated pointer in case
of error.
Fixes: 7ad65bf68d70 ("caif: Add support for CAIF over CDC NCM USB interface") Cc: stable@vger.kernel.org Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of caif_enroll_dev() fail, allocated
link_support won't be assigned to the corresponding
structure. So simply free allocated pointer in case
of error
Fixes: 7c18d2205ea7 ("caif: Restructure how link caif link layer enroll") Cc: stable@vger.kernel.org Reported-and-tested-by: syzbot+7ec324747ce876a29db6@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
caif_enroll_dev() can fail in some cases. Ingnoring
these cases can lead to memory leak due to not assigning
link_support pointer to anywhere.
Fixes: 7c18d2205ea7 ("caif: Restructure how link caif link layer enroll") Cc: stable@vger.kernel.org Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hci_sock_dev_event() function will cleanup the hdev object for
sockets even if this object may still be in used within the
hci_sock_bound_ioctl() function, result in UAF vulnerability.
This patch replace the BH context lock to serialize these affairs
and prevent the race condition.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the cleanup routine for failed initialization of HCI device,
the flush_work(&hdev->rx_work) need to be finished before the
flush_work(&hdev->cmd_work). Otherwise, the hci_rx_work() can
possibly invoke new cmd_work and cause a bug, like double free,
in late processings.
This was assigned CVE-2021-3564.
This patch reorder the flush_work() to fix this bug.
Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Hao Xiong <mart1n@zju.edu.cn> Cc: stable <stable@vger.kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private helper data size cannot be updated. However, updates that
contain NFCTH_PRIV_DATA_LEN might bogusly hit EBUSY even if the size is
the same.
clang doesn't like printing a 32-bit integer using %hX format string:
drivers/hid/i2c-hid/i2c-hid-core.c:994:18: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~
drivers/hid/i2c-hid/i2c-hid-core.c:994:31: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~~
Use an explicit cast to truncate it to the low 16 bits instead.
syzbot reported memory leak [1] when adding service with
HASHED flag. We should ignore this flag both from sockopt
and netlink provided data, otherwise the service is not
hashed and not visible while releasing resources.
zap_vma_ptes() is only available when CONFIG_MMU is set/enabled.
Without CONFIG_MMU, vfio_pci.o has build errors, so make
VFIO_PCI depend on MMU.
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `vfio_pci_mmap_open':
vfio_pci.c:(.text+0x1ec): undefined reference to `zap_vma_ptes'
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `.L0 ':
vfio_pci.c:(.text+0x165c): undefined reference to `zap_vma_ptes'
Fixes: 11c4cd07ba11 ("vfio-pci: Fault mmaps to enable vma tracking") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Cornelia Huck <cohuck@redhat.com> Cc: kvm@vger.kernel.org Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210515190856.2130-1-rdunlap@infradead.org> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
snprintf() should be given the full buffer size, not one less. And it
guarantees nul-termination, so doing it manually afterwards is
pointless.
It's even potentially harmful (though probably not in practice because
CPER_REC_LEN is 256), due to the "return how much would have been
written had the buffer been big enough" semantics. I.e., if the bank
and/or device strings are long enough that the "DIMM location ..."
output gets truncated, writing to msg[n] is a buffer overflow.
UEFI spec 2.9, p.108, table 4-1 lists the scenario that both attributes
are cleared with the description "No memory access protection is
possible for Entry". So we can have valid entries where both attributes
are cleared, so remove the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: 10f0d2f577053 ("efi: Implement generic support for the Memory Attributes table") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472
https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.
Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[fixes gcc-11 build warnings - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new clang diagnostic (-Wsizeof-array-div) warns about the calculation
to determine the number of u32's in an array of unsigned longs.
Suppress warning by adding parentheses.
While looking at the above issue, noticed that the 'address' parameter
to hugetlb_fault_mutex_hash is no longer used. So, remove it from the
definition and all callers.
No functional change.
Link: http://lkml.kernel.org/r/20190919011847.18400-1-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Davidlohr Bueso <dbueso@suse.de> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Ilie Halip <ilie.halip@gmail.com> Cc: David Bolvansky <david.bolvansky@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rt2880_wdt.c uses (well, attempts to use) rt_sysc_membase. However,
when this watchdog driver is built as a loadable module, there is a
build error since the rt_sysc_membase symbol is not exported.
Export it to quell the build error.
board-xxs1500.c references 2 functions without declaring them, so add
the header file to placate the build.
../arch/mips/alchemy/board-xxs1500.c: In function 'board_setup':
../arch/mips/alchemy/board-xxs1500.c:56:2: error: implicit declaration of function 'alchemy_gpio1_input_enable' [-Werror=implicit-function-declaration]
56 | alchemy_gpio1_input_enable();
../arch/mips/alchemy/board-xxs1500.c:57:2: error: implicit declaration of function 'alchemy_gpio2_enable'; did you mean 'alchemy_uart_enable'? [-Werror=implicit-function-declaration]
57 | alchemy_gpio2_enable();
Fixes: 8e026910fcd4 ("MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Manuel Lauss <manuel.lauss@googlemail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If Qdisc_ops->init() is failed, Qdisc_ops->reset() would be called.
When dsmark_init(Qdisc_ops->init()) is failed, it possibly doesn't
initialize dsmark_qdisc_data->q. But dsmark_reset(Qdisc_ops->reset())
uses dsmark_qdisc_data->q pointer wihtout any null checking.
So, panic would occur.
Test commands:
sysctl net.core.default_qdisc=dsmark -w
ip link add dummy0 type dummy
ip link add vw0 link dummy0 type virt_wifi
ip link set vw0 up
Commit dbd1759e6a9c ("ipv6: on reassembly, record frag_max_size")
filled the frag_max_size field in IP6CB in the input path.
The field should also be filled in case of atomic fragments.
Fixes: dbd1759e6a9c ('ipv6: on reassembly, record frag_max_size') Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9e4 ("ixgbe: Enable jumbo frames support w/ SR-IOV") Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com> Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The skb_change_head() helper did not set "skb->mac_len", which is
problematic when it's used in combination with skb_redirect_peer().
Without it, redirecting a packet from a L3 device such as wireguard to
the veth peer device will cause skb->data to point to the middle of the
IP header on entry to tcp_v4_rcv() since the L2 header is not pulled
correctly due to mac_len=0.
Fixes: 3a0af8fd61f9 ("bpf: BPF for lightweight tunnel infrastructure") Signed-off-by: Jussi Maki <joamaki@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210519154743.2554771-2-joamaki@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This error path returns zero (success) but it should return -EINVAL.
Fixes: 3333cb7187b9 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/YKXuyGEzhPT35R3G@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mld_newpack() doesn't allow to allocate high order page,
only order-0 allocation is allowed.
If headroom size is too large, a kernel panic could occur in skb_put().
Test commands:
ip netns del A
ip netns del B
ip netns add A
ip netns add B
ip link add veth0 type veth peer name veth1
ip link set veth0 netns A
ip link set veth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set veth0 up
ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0
ip netns exec B ip link set lo up
ip netns exec B ip link set veth1 up
ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1
for i in {1..99}
do
let A=$i-1
ip netns exec A ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100
ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i
ip netns exec A ip link set ip6gre$i up
ip netns exec B ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100
ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i
ip netns exec B ip link set ip6gre$i up
done
Allowing high order page allocation could fix this problem.
Fixes: 72e09ad107e7 ("ipv6: avoid high order allocations") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to return -EPERM from the error handling case instead of 0, as done
elsewhere in this function.
Fixes: b6016b767397 ("[BNX2]: New Broadcom gigabit network driver.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the error handling path of the
probe function and in remove function.
Suggested-By: Andrew Lunn <andrew@lunn.ch> Fixes: 35d2aeac9810 ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the remove function.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: xinhui pan <xinhui.pan@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
See MS-SMB2 3.2.4.1.4, file ids in compounded requests should be set to
0xFFFFFFFFFFFFFFFF (we were treating it as u32 not u64 and setting
it incorrectly).
Signed-off-by: Steve French <stfrench@microsoft.com> Reported-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can get -EIO or any number of legitimate errors from
btrfs_search_slot(), panicing here is not the appropriate response. The
error path for this code handles errors properly, simply return the
error.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This came up in the discussion of the requirements of qspinlock on an
architecture. OpenRISC uses qspinlock, but it was noticed that the
memmory barrier was not defined.
Peter defined it in the mail thread writing:
As near as I can tell this should do. The arch spec only lists
this one instruction and the text makes it sound like a completion
barrier.
This is correct so applying this patch.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
[shorne@gmail.com:Turned the mail into a patch] Signed-off-by: Stafford Horne <shorne@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 391e2f25601e ("[SCSI] BusLogic: Port driver to 64-bit")
introduced a serious issue for 64-bit systems. With this commit,
64-bit kernel will enumerate 8*15 non-existing disks. This is caused
by the broken CCB structure. The change from u32 data to void *data
increased CCB length on 64-bit system, which introduced an extra 4
byte offset of the CDB. This leads to incorrect response to INQUIRY
commands during enumeration.
Fix disk enumeration failure by reverting the portion of the commit
above which switched the data pointer from u32 to void.
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Place a comment in hidma_mgmt_init explaining why success must
currently be assumed, due to the cleanup issue that would need to
be considered were this module ever to be unloadable or were this
platform_driver_register call ever to fail.
Acked-By: Vinod Koul <vkoul@kernel.org> Acked-By: Sinan Kaya <okaya@kernel.org> Signed-off-by: Phillip Potter <phil@philpotter.co.uk> Link: https://lore.kernel.org/r/20210503115736.2104747-52-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move hw->cfg.mode and hw->addr.mode assignments from hw->ci->cfg_mode
and hw->ci->addr_mode respectively, to be before the subsequent checks
for memory IO mode (and possible ioremap calls in this case).
Also introduce ioremap error checks at both locations. This allows
resources to be properly freed on ioremap failure, as when the caller
of setup_io then subsequently calls release_io via its error path,
release_io can now correctly determine the mode as it has been set
before the ioremap call.
Finally, refactor release_io function so that it will call
release_mem_region in the memory IO case, regardless of whether or not
hw->cfg.p/hw->addr.p are NULL. This means resources are then properly
released on failure.
This properly implements the original reverted commit (d721fe99f6ad)
from the University of Minnesota, whilst also implementing the ioremap
check for the hw->ci->cfg_mode if block as well.
The function hpet_resources() calls ioremap() two times, but in both
cases it does not check if ioremap() returned a null pointer. Fix this
by adding null pointer checks and returning an appropriate error.
The condition of dev == NULL is impossible in caif_xmit(), hence it is
for the removal.
Explanation:
The static caif_xmit() is only called upon via a function pointer
`ndo_start_xmit` defined in include/linux/netdevice.h:
```
struct net_device_ops {
...
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev);
...
}
```
The exhausive list of call points are:
```
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c
dev->netdev_ops->ndo_start_xmit(skb, dev);
^ ^
drivers/infiniband/ulp/opa_vnic/opa_vnic_netdev.c
struct opa_vnic_adapter *adapter = opa_vnic_priv(netdev);
^ ^
return adapter->rn_ops->ndo_start_xmit(skb, netdev); // adapter would crash first
^ ^
In each of the enumerated scenarios, it is impossible for the NULL-valued dev to
reach the caif_xmit() without crashing the kernel earlier, therefore `BUG_ON(dev ==
NULL)` is rather useless, hence the removal.
In fmvj18x_get_hwinfo(), if ioremap fails there will be NULL pointer
deref. To fix this, check the return value of ioremap and return -1
to the caller in case of failure.
The macro "spi_register_driver" invokes the function
"__spi_register_driver()" which has a return type of int and can fail,
returning a negative value in such a case. This is currently ignored and
the init() function yields success even if the spi driver failed to
register.
Fix this by collecting the return value of "__spi_register_driver()" and
also unregister the uart driver in case of failure.
On some hosts, rlim.rlim_max can be returned as RLIM_INFINITY.
By casting it to int, it is interpreted as -1, which will cause get_maxfds
to return 0, causing "Invalid argument" errors in nftw() calls.
Fix this by casting the second argument of min() to rlim_t instead.
Fixes: 80eeb67fe577 ("perf jevents: Program to convert JSON file") Signed-off-by: Felix Fietkau <nbd@nbd.name> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Link: http://lore.kernel.org/lkml/20210525160758.97829-1-nbd@nbd.name Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the i2c-i801 driver supports interrupts, setting the KILL bit
in a attempt to recover from a timed out transaction triggers an
interrupt. Unfortunately, the interrupt handler (i801_isr) is not
prepared for this situation and will try to process the interrupt as
if it was signaling the end of a successful transaction. In the case
of a block transaction, this can result in an out-of-range memory
access.
Interrupt handler processes multiple message write requests one after
another, till the driver message queue is drained. However if driver
encounters a read message without preceding START, it stops the I2C
transfer as it is an invalid condition for the controller. At least the
comment describes a requirement "the controller forces us to send a new
START when we change direction". This stop results in clearing the
message queue (i2c->msg = NULL).
The code however immediately jumped back to label "retry_write" which
dereferenced the "i2c->msg" making it a possible NULL pointer
dereference.
The Coverity analysis:
1. Condition !is_msgend(i2c), taking false branch.
if (!is_msgend(i2c)) {
4. write_zero_model: Passing i2c to s3c24xx_i2c_stop, which sets i2c->msg to NULL.
s3c24xx_i2c_stop(i2c, -EINVAL);
5. Jumping to label retry_write.
goto retry_write;
6. var_deref_model: Passing i2c to is_msgend, which dereferences null i2c->msg.
if (!is_msgend(i2c)) {"
All previous calls to s3c24xx_i2c_stop() in this interrupt service
routine are followed by jumping to end of function (acknowledging
the interrupt and returning). This seems a reasonable choice also here
since message buffer was entirely emptied.
Addresses-Coverity: Explicit null dereferenced Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not a good idea to append the frag skb to a skb's frag_list if
the frag_list already has skbs from elsewhere, such as this skb was
created by pskb_copy() where the frag_list was cloned (all the skbs
in it were skb_get'ed) and shared by multiple skbs.
However, the new appended frag skb should have been only seen by the
current skb. Otherwise, it will cause use after free crashes as this
appended frag skb are seen by multiple skbs but it only got skb_get
called once.
The same thing happens with a skb updated by pskb_may_pull() with a
skb_cloned skb. Li Shuang has reported quite a few crashes caused
by this when doing testing over macvlan devices:
This patch is to fix it by linearizing the head skb if it has frag_list
set in tipc_buf_append(). Note that we choose to do this before calling
skb_unshare(), as __skb_linearize() will avoid skb_copy(). Also, we can
not just drop the frag_list either as the early time.
Fixes: 45c8b7b175ce ("tipc: allow non-linear first fragment buffer") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 6bf24dc0cc0c ("net:tipc: Fix a double free in tipc_sk_mcast_rcv") Acked-by: Jon Maloy <jmaloy@redhat.com> Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix SFP and QSFP* EEPROM queries by setting i2c_address, offset and page
number correctly. For SFP set the following params:
- I2C address for offsets 0-255 is 0x50. For 256-511 - 0x51.
- Page number is zero.
- Offset is 0-255.
At the same time, QSFP* parameters are different:
- I2C address is always 0x50.
- Page number is not limited to zero.
- Offset is 0-255 for page zero and 128-255 for others.
To set parameters accordingly to cable used, implement function to query
module ID and implement respective helper functions to set parameters
correctly.
Fixes: 135dd9594f12 ("net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bdcc2cd14e4e ("NFSv4.2: handle NFS-specific llseek errors"),
nfs42_proc_llseek would return -EOPNOTSUPP rather than -ENOTSUPP when
SEEK_DATA on NFSv4.0/v4.1.
This will lead xfstests generic/285 not run on NFSv4.0/v4.1 when set the
CONFIG_NFS_V4_2, rather than run failed.
The "sizeof(struct nfs_fh)" is two bytes too large and could lead to
memory corruption. It should be NFS_MAXFHSIZE because that's the size
of the ->data[] buffer.
I reversed the size of the arguments to put the variable on the left.
When cmtp_attach_device fails, cmtp_add_connection returns the error value
which leads to the caller to doing fput through sockfd_put. But
cmtp_session kthread, which is stopped in this path will also call fput,
leading to a potential refcount underflow or a use-after-free.
Add a refcount before we signal the kthread to stop. The kthread will try
to grab the cmtp_session_sem mutex before doing the fput, which is held
when get_file is called, so there should be no races there.
Reported-by: Ryota Shiga Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb3_start_pipen() is called by renesas_usb3_ep_queue() and
usb3_request_done_pipen() so that usb3_start_pipen() is possible
to cause a race when getting usb3_first_req like below:
renesas_usb3_ep_queue()
spin_lock_irqsave()
list_add_tail()
spin_unlock_irqrestore()
usb3_start_pipen()
usb3_first_req = usb3_get_request() --- [1]
--- interrupt ---
usb3_irq_dma_int()
usb3_request_done_pipen()
usb3_get_request()
usb3_start_pipen()
usb3_first_req = usb3_get_request()
...
(the req is possible to be finished in the interrupt)
The usb3_first_req [1] above may have been finished after the interrupt
ended so that this driver caused to start a transfer wrongly. To fix this
issue, getting/checking the usb3_first_req are under spin_lock_irqsave()
in the same section.
projects / linux-stable / log