USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Cc: stable@vger.kernel.org # 2.6.37 Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211025120910.6339-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bulk and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.
Note that the bulk-out transfer timeout was set to the endpoint
bInterval value, which should be ignored for bulk endpoints and is
typically set to zero. This meant that a failing bulk-out transfer
would never time out.
Assume that the 10 second timeout used for all other transfers is more
than enough also for the bulk-out endpoint.
Fixes: 985cafccbf9b ("Staging: Comedi: vmk80xx: Add k8061 support") Fixes: 951348b37738 ("staging: comedi: vmk80xx: wait for URBs to complete") Cc: stable@vger.kernel.org # 2.6.31 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20211025114532.4599-6-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using endpoint-sized buffers but must not assume that the
tx and rx buffers are of equal size or a malicious device could overflow
the slab-allocated receive buffer when doing bulk transfers.
The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.
Commit e1f13c879a7c ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.
Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.
The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize.
The driver uses endpoint-sized USB transfer buffers but had no sanity
checks on the sizes. This can lead to zero-size-pointer dereferences or
overflowed transfer buffers in ni6501_port_command() and
ni6501_counter_command() if a (malicious) device has smaller max-packet
sizes than expected (or when doing descriptor fuzz testing).
Add the missing sanity checks to probe().
Fixes: a03bb00e50ab ("staging: comedi: add NI USB-6501 support") Cc: stable@vger.kernel.org # 3.18 Cc: Luca Ellero <luca.ellero@brickedbrain.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211027093529.30896-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.
Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.
Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is.
Fixes: 63274cd7d38a ("Staging: comedi: add usb dt9812 driver") Cc: stable@vger.kernel.org # 2.6.29 Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211027093529.30896-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When isofs image is suitably corrupted isofs_read_inode() can read data
beyond the end of buffer. Sanity-check the directory entry length before
using it.
Reported-and-tested-by: syzbot+6fc7fb214625d82af7d1@syzkaller.appspotmail.com CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 48021f98130880dd74 ("printk: handle blank console arguments
passed in.") prevented crash caused by empty console= parameter value.
Unfortunately, this value is widely used on Chromebooks to disable
the console output. The above commit caused performance regression
because the messages were pushed on slow console even though nobody
was watching it.
Use ttynull driver explicitly for console="" and console=null
parameters. It has been created for exactly this purpose.
It causes that preferred_console is set. As a result, ttySX and ttyX
are not used as a fallback. And only ttynull console gets registered by
default.
It still allows to register other consoles either by additional console=
parameters or SPCR. It prevents regression because it worked this way even
before. Also it is a sane semantic. Preventing output on all consoles
should be done another way, for example, by introducing mute_console
parameter.
These drive enclosures have firmware bugs that make it impossible to mount
a new virtual ISO image after Linux ejects the old one if the device is
locked by Linux. Windows bypasses this problem by the fact that they do
not lock the device. Add a quirk to disable device locking for these
drive enclosures.
musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.
Remove the request from the list on error.
Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue") Cc: stable <stable@vger.kernel.org> Signed-off-by: Viraj Shah <viraj.shah@linutronix.de> Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
The commit has the wrong reasoning, as KVM_MAX_VCPU_ID is not defining the
maximum allowed vcpu-id as its name suggests, but the number of vcpu-ids.
So revert this patch again.
This patch introduces helpers of 'mp_bvec_iter_*' for multi-page bvec
support.
The introduced helpers treate one bvec as real multi-page segment,
which may include more than one pages.
The existed helpers of bvec_iter_* are interfaces for supporting current
bvec iterator which is thought as single-page by drivers, fs, dm and
etc. These introduced helpers will build single-page bvec in flight, so
this way won't break current bio/bvec users, which needn't any change.
Follows some multi-page bvec background:
- bvecs stored in bio->bi_io_vec is always multi-page style
- bvec(struct bio_vec) represents one physically contiguous I/O
buffer, now the buffer may include more than one page after
multi-page bvec is supported, and all these pages represented
by one bvec is physically contiguous. Before multi-page bvec
support, at most one page is included in one bvec, we call it
single-page bvec.
- .bv_page of the bvec points to the 1st page in the multi-page bvec
- .bv_offset of the bvec is the offset of the buffer in the bvec
The effect on the current drivers/filesystem/dm/bcache/...:
- almost everyone supposes that one bvec only includes one single
page, so we keep the sp interface not changed, for example,
bio_for_each_segment() still returns single-page bvec
- bio_for_each_segment_all() will return single-page bvec too
- during iterating, iterator variable(struct bvec_iter) is always
updated in multi-page bvec style, and bvec_iter_advance() is kept
not changed
- returned(copied) single-page bvec is built in flight by bvec
helpers from the stored multi-page bvec
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overflowing either addrlimit or bytes_togo can allow userspace to trigger
a buffer overflow of kernel memory. Check for overflows in all the places
doing math on user controlled buffers.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Link: https://lore.kernel.org/r/20211012175519.7298.77738.stgit@awfm-01.cornelisnetworks.com Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*pkt) + sizeof(pkt->addr[0])*n
with:
struct_size(pkt, addr, n)
Also, notice that variable size is unnecessary, hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 77a7300abad7 ("of/irq: Get rid of NO_IRQ usage"),
no irq case has been removed, irq_of_parse_and_map() will return
0 in all cases when get error from parse and map an interrupt into
linux virq space.
amba_device_register() is only used on no-DT initialization, see
s3c64xx_pl080_init() arch/arm/mach-s3c/pl080.c
ep93xx_init_devices() arch/arm/mach-ep93xx/core.c
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb3a ("staging: zsmalloc: zsmalloc memory allocation library") Fixes: 02390b87a945 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS") Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
[florian: patch arch/powerpc/include/asm/pte-common.h for 4.14.y
removed arch/riscv/include/asm/pgtable.h which does not exist] Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bounds checking in avc_ca_pmt() is not strict enough. It should
be checking "read_pos + 4" because it's reading 5 bytes. If the
"es_info_length" is non-zero then it reads a 6th byte so there needs to
be an additional check for that.
I also added checks for the "write_pos". I don't think these are
required because "read_pos" and "write_pos" are tied together so
checking one ought to be enough. But they make the code easier to
understand for me. The check on write_pos is:
if (write_pos + 4 >= sizeof(c->operand) - 4) {
The first "+ 4" is because we're writing 5 bytes and the last " - 4"
is to leave space for the CRC.
The other problem is that "length" can be invalid. It comes from
"data_length" in fdtv_ca_pmt().
Cc: stable@vger.kernel.org Reported-by: Luo Likang <luolikang@nsfocus.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCSI host release is triggered when SCSI device is freed. We have to make
sure that the low-level device driver module won't be unloaded before SCSI
host instance is released because shost->hostt is required in the release
handler.
Make sure to put LLD module refcnt after SCSI device is released.
Fixes a kernel panic of 'BUG: unable to handle page fault for address'
reported by Changhui and Yi.
Link: https://lore.kernel.org/r/20211008050118.1440686-1-ming.lei@redhat.com Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Changhui Zhong <czhong@redhat.com> Reported-by: Yi Zhang <yi.zhang@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp_sf_ootb() is called when processing DATA chunk in closed state,
and many other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
When fails to verify the vtag from the chunk, this patch sets asoc
to NULL, so that the abort will be made with the vtag from the
received chunk later.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sctp_sf_do_8_5_1_E_sa() is called when processing SHUTDOWN_ACK chunk
in cookie_wait and cookie_echoed state.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Note that when fails to verify the vtag from SHUTDOWN-ACK chunk,
SHUTDOWN COMPLETE message will still be sent back to peer, but
with the vtag from SHUTDOWN-ACK chunk, as said in 5) of
rfc4960#section-8.4.
While at it, also remove the unnecessary chunk length check from
sctp_sf_shut_8_4_5(), as it's already done in both places where
it calls sctp_sf_shut_8_4_5().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sctp_sf_violation() is called when processing HEARTBEAT_ACK chunk
in cookie_wait state, and some other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When asoc is NULL, making packet for abort will use chunk's vtag
in sctp_ootb_pkt_new(). But when asoc exists, vtag from the chunk
should be verified before using peer.i.init_tag to make packet
for abort in sctp_ootb_pkt_new(), and just discard it if vtag is
not correct.
2. In the other states: in sctp_sf_do_5_2_4_dupcook():
asoc always exists, but duplicate cookie_echo's vtag will be
handled by sctp_tietags_compare() and then take actions, so before
that we only verify the vtag for the abort sent for invalid chunk
length.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently Linux SCTP uses the verification tag of the existing SCTP
asoc when failing to process and sending the packet with the ABORT
chunk. This will result in the peer accepting the ABORT chunk and
removing the SCTP asoc. One could exploit this to terminate a SCTP
asoc.
This patch is to fix it by always using the initiate tag of the
received INIT chunk for the ABORT chunk to be sent.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A hard hang is observed whenever the ethernet interface is brought
down. If the PHY is stopped before the LPC core block is reset,
the SoC will hang. Comparing lpc_eth_close() and lpc_eth_open() I
re-arranged the ordering of the functions calls in lpc_eth_close() to
reset the hardware before stopping the PHY. Fixes: b7370112f519 ("lpc32xx: Added ethernet driver") Signed-off-by: Trevor Woerner <twoerner@gmail.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make[1]: *** No rule to make target 'arch/nios2/boot/dts/""',
needed by 'arch/nios2/boot/dts/built-in.a'. Stop.
make: [Makefile:1868: arch/nios2/boot/dts] Error 2 (ignored)
This is seen with compile tests since those enable NIOS2_DTB_SOURCE_BOOL,
which in turn enables NIOS2_DTB_SOURCE. This causes the build error
because the default value for NIOS2_DTB_SOURCE is an empty string.
Disable NIOS2_DTB_SOURCE_BOOL for compile tests to avoid the error.
Syzbot reported ODEBUG warning in batadv_nc_mesh_free(). The problem was
in wrong error handling in batadv_mesh_init().
Before this patch batadv_mesh_init() was calling batadv_mesh_free() in case
of any batadv_*_init() calls failure. This approach may work well, when
there is some kind of indicator, which can tell which parts of batadv are
initialized; but there isn't any.
All written above lead to cleaning up uninitialized fields. Even if we hide
ODEBUG warning by initializing bat_priv->nc.work, syzbot was able to hit
GPF in batadv_nc_purge_paths(), because hash pointer in still NULL. [1]
To fix these bugs we can unwind batadv_*_init() calls one by one.
It is good approach for 2 reasons: 1) It fixes bugs on error handling
path 2) It improves the performance, since we won't call unneeded
batadv_*_free() functions.
So, this patch makes all batadv_*_init() clean up all allocated memory
before returning with an error to no call correspoing batadv_*_free()
and open-codes batadv_mesh_free() with proper order to avoid touching
uninitialized fields.
Link: https://lore.kernel.org/netdev/000000000000c87fbd05cef6bcb0@google.com/ Reported-and-tested-by: syzbot+28b0702ada0bf7381f58@syzkaller.appspotmail.com Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 3f4ff561bc88b ("regmap: rbtree: Make cache_present bitmap per node") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: stable@vger.kernel.org # 4.3 Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.
Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
During probing, the driver tries to get a list (mask) of supported
command types in port100_get_command_type_mask() function. The value
is u64 and 0 is treated as invalid mask (no commands supported). The
function however returns also -ERRNO as u64 which will be interpret as
valid command mask.
Return 0 on every error case of port100_get_command_type_mask(), so the
probing will stop.
Cc: <stable@vger.kernel.org> Fixes: 0347a6ab300a ("NFC: port100: Commands mechanism implementation") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return error code if usb_maxpacket() returns 0 in usbnet_probe()
Fixes: 397430b50a36 ("usbnet: sanity check for maxpacket") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211026124015.3025136-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been a no-op in binutils since 2004 (see commit dea514f51da1 in
that tree). Given that the lowest officially supported of binutils for
the kernel is 2.20, which was released in 2009, nobody needs this flag
around so just remove it. Commit 1a381d4a0a9a ("arm64: remove no-op -p
linker flag") did the same for arm64.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by: Song Liu <songliubraving@fb.com> Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/c674ca18c3046885602caebb326213731c675d06.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
[cascardo: use PPC_LI instead of EMIT(PPC_RAW_LI)] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With extra warnings enabled, gcc complains about this function
definition:
arch/arm/probes/kprobes/core.c: In function 'arch_init_kprobes':
arch/arm/probes/kprobes/core.c:465:12: warning: old-style function definition [-Wold-style-definition]
465 | int __init arch_init_kprobes()
Both the decompressor code and the kasan logic try to override
the memcpy() and memmove() definitions, which leading to a clash
in a KASAN-enabled kernel with XZ decompression:
A kernel built with CONFIG_THUMB2_KERNEL=y and using clang as the
assembler could generate non-naturally-aligned v7wbi_tlb_fns which
results in a boot failure. The original commit adding the macro missed
the .align directive on this data.
tglx notes:
This function [futex_detect_cmpxchg] is only needed when an
architecture has to runtime discover whether the CPU supports it or
not. ARM has unconditional support for this, so the obvious thing to
do is the below.
Fixes linkage failure from Clang randconfigs:
kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text'
and boot failures for CONFIG_THUMB2_KERNEL.
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/ Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com> Cc: Helge Deller <deller@gmx.de> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Jisheng Zhang <jszhang@kernel.org> Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com> Cc: Guo Ren <guoren@kernel.org> Cc: stable@vger.kernel.org Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at
can_queue"), a 416-CPU VM running on Hyper-V hangs during boot because the
hv_storvsc driver sets scsi_driver.can_queue to an integer value that
exceeds SHRT_MAX, and hence scsi_add_host_with_dma() sets
shost->cmd_per_lun to a negative "short" value.
Use min_t(int, ...) to work around the issue.
Link: https://lore.kernel.org/r/20211008043546.6006-1-decui@microsoft.com Fixes: ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at can_queue") Cc: stable@vger.kernel.org Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5ed ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449be ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org> Cc: Benson Leung <bleung@chromium.org> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently inode_in_dir() ignores errors returned from
btrfs_lookup_dir_index_item() and from btrfs_lookup_dir_item(), treating
any errors as if the directory entry does not exists in the fs/subvolume
tree, which is obviously not correct, as we can get errors such as -EIO
when reading extent buffers while searching the fs/subvolume's tree.
Fix that by making inode_in_dir() return the errors and making its only
caller, add_inode_ref(), deal with returned errors as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During this process, the kernel thread would call detach_capi_ctr()
to detach a register controller. if the controller
was not attached yet, detach_capi_ctr() would
trigger an array-index-out-bounds bug.
[ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in
drivers/isdn/capi/kcapi.c:483:21
[ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]'
[ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted
5.15.0-rc2+ #8
[ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX,
1996), BIOS 1.14.0-2 04/01/2014
[ 46.870107][ T6479] Call Trace:
[ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d
[ 46.870974][ T6479] ubsan_epilogue+0x5/0x40
[ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48
[ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0
[ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0
[ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60
[ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120
[ 46.874256][ T6479] kthread+0x147/0x170
[ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40
[ 46.875248][ T6479] ret_from_fork+0x1f/0x30
[ 46.875773][ T6479]
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put callback of a kcontrol is supposed to return 1 when the value
is changed, and this will be notified to user-space. However, some
DAPM kcontrols always return 0 (except for errors), hence the
user-space misses the update of a control value.
This patch corrects the behavior by properly returning 1 when the
value gets updated.
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13
The GSP670 has 2 playback and 1 recording device that by default are
detected in an incompatible order for alsa. This may have been done to make
it compatible for the console by the manufacturer and only affects the
latest firmware which uses its own ID.
This quirk will resolve this by reordering the channels.
If we open a file without read access and then pass the fd to a syscall
whose implementation calls kernel_read_file_from_fd(), we get a warning
from __kernel_read():
if (WARN_ON_ONCE(!(file->f_mode & FMODE_READ)))
This currently affects both finit_module() and kexec_file_load(), but it
could affect other syscalls in the future.
Link: https://lkml.kernel.org/r/20211007220110.600005-1-willy@infradead.org Fixes: b844f0ecbc56 ("vfs: define kernel_copy_file_from_fd()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reported-by: Hao Sun <sunhao.th@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Mimi Zohar <zohar@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6e7b64b9dd6d ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an
ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the
trace below. Problem seems to be that strings for cluster stack and
cluster name are not guaranteed to be null terminated in the disk
representation, while strlcpy assumes that the source string is always
null terminated. This causes a read outside of the source string
triggering the buffer overflow detection.
Commit 6dbf7bb55598 ("fs: Don't invalidate page buffers in
block_write_full_page()") uncovered a latent bug in ocfs2 conversion
from inline inode format to a normal inode format.
The code in ocfs2_convert_inline_data_to_extents() attempts to zero out
the whole cluster allocated for file data by grabbing, zeroing, and
dirtying all pages covering this cluster. However these pages are
beyond i_size, thus writeback code generally ignores these dirty pages
and no blocks were ever actually zeroed on the disk.
This oversight was fixed by commit 693c241a5f6a ("ocfs2: No need to zero
pages past i_size.") for standard ocfs2 write path, inline conversion
path was apparently forgotten; the commit log also has a reasoning why
the zeroing actually is not needed.
After commit 6dbf7bb55598, things became worse as writeback code stopped
invalidating buffers on pages beyond i_size and thus these pages end up
with clean PageDirty bit but with buffers attached to these pages being
still dirty. So when a file is converted from inline format, then
writeback triggers, and then the file is grown so that these pages
become valid, the invalid dirtiness state is preserved,
mark_buffer_dirty() does nothing on these pages (buffers are already
dirty) but page is never written back because it is clean. So data
written to these pages is lost once pages are reclaimed.
After unmounting and mounting the fs again, you can observe that end of
'ocfs2_file' has lost its contents.
Fix the problem by not doing the pointless zeroing during conversion
from inline format similarly as in the standard write path.
[akpm@linux-foundation.org: fix whitespace, per Joseph]
Link: https://lkml.kernel.org/r/20210930095405.21433-1-jack@suse.cz Fixes: 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com> Acked-by: Gang He <ghe@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: "Markov, Andrey" <Markov.Andrey@Dell.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both arch/nios2/ and drivers/mmc/host/tmio_mmc.c define a macro
with the name "CTL_STATUS". Change the one in arch/nios2/ to be
"CTL_FSTATUS" (flags status) to eliminate the build warning.
In file included from ../drivers/mmc/host/tmio_mmc.c:22:
drivers/mmc/host/tmio_mmc.h:31: warning: "CTL_STATUS" redefined
31 | #define CTL_STATUS 0x1c
arch/nios2/include/asm/registers.h:14: note: this is the location of the previous definition
14 | #define CTL_STATUS 0
If nfsd has existing listening sockets without any processes, then an error
returned from svc_create_xprt() for an additional transport will remove
those existing listeners. We're seeing this in practice when userspace
attempts to create rpcrdma transports without having the rpcrdma modules
present before creating nfsd kernel processes. Fix this by checking for
existing sockets before calling nfsd_destroy().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rebooting xtensa images loaded with the '-kernel' option in qemu does
not work. When executing a reboot command, the qemu session either hangs
or experiences an endless sequence of error messages.
Kernel panic - not syncing: Unrecoverable error in exception handler
Reset code jumps to the CPU restart address, but Linux can not recover
from there because code and data in the kernel init sections have been
discarded and overwritten at this point.
XTFPGA platforms have a means to reset the CPU by writing 0xdead into a
specific FPGA IO address. When used in QEMU the kernel image loaded with
the '-kernel' option gets restored to its original state allowing the
machine to boot successfully.
Use that mechanism to attempt a platform reset. If it does not work,
fall back to the existing mechanism.
Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF
is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not
selected but CONFIG_OF is.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without a sensor node, the ISC will simply fail to probe, as the
corresponding port node is missing.
It is then logical to disable the node in the devicetree.
If we add a port with a connection to a sensor endpoint, ISC can be enabled.
There's a priority inversion that exists currently with btrfs fsync. In
some cases we will collect outstanding ordered extents onto a list and
only wait on them at the very last second. However this "very last
second" falls inside of a transaction handle, so if we are in a lower
priority cgroup we can end up holding the transaction open for longer
than needed, so if a high priority cgroup is also trying to fsync()
it'll see latency.
Signed-off-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a2a1 ("r8152: support request_firmware for RTL8153") Fixes: ac718b69301c7 ("net/usb: new driver for RTL8152") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
The initialization of pointer dev dereferences pointer edp before
edp is null checked, so there is a potential null pointer deference
issue. Fix this by only dereferencing edp after edp has been null
checked.
Addresses-Coverity: ("Dereference before null check") Fixes: ab5b0107ccf3 ("drm/msm: Initial add eDP support in msm drm driver (v5)") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210929121857.213922-1-colin.king@canonical.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes: 2c66daecc409 ("NFC Digital: Add NFC-A technology support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes: 1c7a4c24fbfd ("NFC Digital: Add target NFC-DEP support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nfc proto id is using, nfc_proto_register() return -EBUSY error
code, but forgot to unregister proto. Fix it by adding proto_unregister()
in the error handling case.
Fixes: c7fe3b52c128 ("NFC: add NFC socket family") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211013034932.2833737-1-william.xuanziyang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
devm_regmap_init may return error which caused by like out of memory,
this will results in null pointer dereference later when reading
or writing register:
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode':
emac_main.c:(.text+0xb11): undefined reference to `crc32_le'
The crc32_le() call comes through the ether_crc_le() call in
arc_emac_set_rx_mode().
[v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing,
but the error comes from emac_main.o, which is part of the arc_emac module,
which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is
different from emac_arc...]
sctp_make_strreset_req() makes repeated calls to sctp_addto_chunk()
which will automatically account for padding on each call. inreq and
outreq are already 4 bytes aligned, but the payload is not and doing
SCTP_PAD4(a + b) (which _sctp_make_chunk() did implicitly here) is
different from SCTP_PAD4(a) + SCTP_PAD4(b) and not enough. It led to
possible attempt to use more buffer than it was allocated and triggered
a BUG_ON.
The ssp_print_mcu_debug() function should return negative error codes on
error. Returning "length" is meaningless. This change does not affect
runtime because the callers only care about zero/non-zero.
Reported-by: Jonathan Cameron <jic23@kernel.org> Fixes: 50dd64d57eee ("iio: common: ssp_sensors: Add sensorhub driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20210914105333.GA11657@kili Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A successful 'regulator_enable()' call should be balanced by a
corresponding 'regulator_disable()' call in the error handling path of the
probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: 913b86468674 ("iio: adc: Add TI ADC128S052") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com> Link: https://lore.kernel.org/r/85189f1cfcf6f5f7b42d8730966f2a074b07b5f5.1629542160.git.christophe.jaillet@wanadoo.fr Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Kconfig option was added initially so that memory encryption is
enabled by default on machines which support it.
However, devices which have DMA masks that are less than the bit
position of the encryption bit, aka C-bit, require the use of an IOMMU
or the use of SWIOTLB.
If the IOMMU is disabled or in passthrough mode, the kernel would switch
to SWIOTLB bounce-buffering for those transfers.
In order to avoid that,
2cc13bb4f59f ("iommu: Disable passthrough mode when SME is active")
disables the default IOMMU passthrough mode so that devices for which the
default 256K DMA is insufficient, can use the IOMMU instead.
However 2, there are cases where the IOMMU is disabled in the BIOS, etc.
(think the usual hardware folk "oops, I dropped the ball there" cases) or a
driver doesn't properly use the DMA APIs or a device has a firmware or
hardware bug, e.g.:
ea68573d408f ("drm/amdgpu: Fail to load on RAVEN if SME is active")
However 3, in the above GPU use case, there are APIs like Vulkan and
some OpenGL/OpenCL extensions which are under the assumption that
user-allocated memory can be passed in to the kernel driver and both the
GPU and CPU can do coherent and concurrent access to the same memory.
That cannot work with SWIOTLB bounce buffers, of course.
So, in order for those devices to function, drop the "default y" for the
SME by default active option so that users who want to have SME enabled,
will need to either enable it in their config or use "mem_encrypt=on" on
the kernel command line.