In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reported-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in theory multiple unwinders could be compiled in, it does
not make sense in practise. Use a choice to make the unwinder
selection mutually exclusive and mandatory.
Already before this commit it has not been possible to deselect
FRAME_POINTER. Remove the obsolete comment.
Furthermore, to produce a meaningful backtrace with FRAME_POINTER
enabled the kernel needs a specific function prologue:
mov ip, sp
stmfd sp!, {fp, ip, lr, pc}
sub fp, ip, #4
To get to the required prologue gcc uses apcs and no-sched-prolog.
This compiler options are not available on clang, and clang is not
able to generate the required prologue. Make the FRAME_POINTER
config symbol depending on !clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Link: https://github.com/ClangBuiltLinux/linux/issues/1146 Reported-by: Andy Lavr <andy.lavr@gmail.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The naked attribute is known to confuse some old gcc versions when
function arguments aren't explicitly listed as inline assembly operands
despite the gcc documentation. That resulted in commit 9a40ac86152c
("ARM: 6164/1: Add kto and kfrom to input operands list.").
Yet that commit has problems of its own by having assembly operand
constraints completely wrong. If the generated code has been OK since
then, it is due to luck rather than correctness. So this patch also
provides proper assembly operand constraints, and removes two instances
of redundant register usages in the implementation while at it.
Inspection of the generated code with this patch doesn't show any
obvious quality degradation either, so not relying on __naked at all
will make the code less fragile, and avoid some issues with clang.
The only remaining __naked instances (excluding the kprobes test cases)
are exynos_pm_power_up_setup(), tc2_pm_power_up_setup() and
cci_enable_port_for_self(. But in the first two cases, only the function
address is used by the compiler with no chance of inlining it by
mistake, and the third case is called from assembly code only. And the
fact that no stack is available when the corresponding code is executed
does warrant the __naked usage in those cases.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/129 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In resp_mode_select() sanity check the block descriptor len to avoid UAF.
BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032
Without the bound checks for scpi_pd->name, it could result in the buffer
overflow when copying the SCPI device name from the corresponding device
tree node as the name string is set at maximum size of 30.
Let us fix it by using devm_kasprintf so that the string buffer is
allocated dynamically.
Fixes: 8bec4337ad40 ("firmware: scpi: add device power domain support using genpd") Reported-by: Pedro Batista <pedbap.g@gmail.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org Cc: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20211209120456.696879-1-sudeep.holla@arm.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries") Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-pci@vger.kernel.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Marek Vasut <marex@denx.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.
Fixes: 61fad6816fc1 ("net/packet: tpacket_rcv: avoid a producer race condition") Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed") Signed-off-by: Cyril Novikov <cnovikov@lynx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions) Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification") Link: https://github.com/ClangBuiltLinux/linux/issues/1488 Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reserving memory using efi_mem_reserve() calls into the x86
efi_arch_mem_reserve() function. This function will insert a new EFI
memory descriptor into the EFI memory map representing the area of
memory to be reserved and marking it as EFI runtime memory. As part
of adding this new entry, a new EFI memory map is allocated and mapped.
The mapping is where a problem can occur. This new memory map is mapped
using early_memremap() and generally mapped encrypted, unless the new
memory for the mapping happens to come from an area of memory that is
marked as EFI_BOOT_SERVICES_DATA memory. In this case, the new memory will
be mapped unencrypted. However, during replacement of the old memory map,
efi_mem_type() is disabled, so the new memory map will now be long-term
mapped encrypted (in efi.memmap), resulting in the map containing invalid
data and causing the kernel boot to crash.
Since it is known that the area will be mapped encrypted going forward,
explicitly map the new memory map as encrypted using early_memremap_prot().
Cc: <stable@vger.kernel.org> # 4.14.x Fixes: 8f716c9b5feb ("x86/mm: Add support to access boot related data in the clear") Link: https://lore.kernel.org/all/ebf1eb2940405438a09d51d121ec0d02c8755558.1634752931.git.thomas.lendacky@amd.com/ Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ardb: incorporate Kconfig fix by Arnd] Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn ARCH_USE_MEMREMAP_PROT into a generic Kconfig symbol, and fix the
dependency expression to reflect that AMD_MEM_ENCRYPT depends on it,
instead of the other way around. This will permit ARCH_USE_MEMREMAP_PROT
to be selected by other architectures.
Note that the encryption related early memremap routines in
arch/x86/mm/ioremap.c cannot be built for 32-bit x86 without triggering
the following warning:
arch/x86//mm/ioremap.c: In function 'early_memremap_encrypted':
>> arch/x86/include/asm/pgtable_types.h:193:27: warning: conversion from
'long long unsigned int' to 'long unsigned int' changes
value from '9223372036854776163' to '355' [-Woverflow]
#define __PAGE_KERNEL_ENC (__PAGE_KERNEL | _PAGE_ENC)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86//mm/ioremap.c:713:46: note: in expansion of macro '__PAGE_KERNEL_ENC'
return early_memremap_prot(phys_addr, size, __PAGE_KERNEL_ENC);
which essentially means they are 64-bit only anyway. However, we cannot
make them dependent on CONFIG_ARCH_HAS_MEM_ENCRYPT, since that is always
defined, even for i386 (and changing that results in a slew of build errors)
So instead, build those routines only if CONFIG_AMD_MEM_ENCRYPT is
defined.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Alexander Graf <agraf@suse.de> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Jeffrey Hugo <jhugo@codeaurora.org> Cc: Lee Jones <lee.jones@linaro.org> Cc: Leif Lindholm <leif.lindholm@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20190202094119.13230-9-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f4523 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[Salvatore Bonaccorso: Backport for context changes to versions which do
not have 20b7d86f29d3 ("nfsd: use boottime for lease expiry calculation")] Signed-off-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org Fixes: 5b52330bbfe63 ("audit: fix auditd/kernel connection state tracking") Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com> Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On s390, recordmcount.pl is looking for "bcrl 0,<xxx>" instructions in
the objdump -d outpout. However since binutils 2.37, objdump -d
display "jgnop <xxx>" for the same instruction. Update the
mcount_regex so that it accepts both.
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503f3 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Acked-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After scrubbing the BPF prog a bit from the noise, turns out it called
bpf_skb_change_head() for the lwt_xmit prog with headroom of 2. Nothing
wrong in that, however, this was run with repeat >> 0 in bpf_prog_test_run_skb()
and the same skb thus keeps changing until the pskb_expand_head() called
from skb_cow() keeps bailing out in atomic alloc context with -ENOMEM.
So upon return we'll basically have 0 headroom left yet blindly do the
__skb_push() of 14 bytes and keep copying data from there in bpf_test_finish()
out of bounds. Fix to check if we have enough headroom and if pskb_expand_head()
fails, bail out with error.
Another bug independent of this fix (but related in triggering above) is
that BPF_PROG_TEST_RUN should be reworked to reset the skb/xdp buffer to
it's original state from input as otherwise repeating the same test in a
loop won't work for benchmarking when underlying input buffer is getting
changed by the prog each time and reused for the next run leading to
unexpected results.
Fixes: 1cf1cae963c2 ("bpf: introduce BPF_PROG_TEST_RUN command") Reported-by: syzbot+709412e651e55ed96498@syzkaller.appspotmail.com Reported-by: syzbot+54f39d6ab58f39720a55@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[connoro: drop test_verifier.c changes not applicable to 4.14] Signed-off-by: Connor O'Brien <connoro@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is elts->pages[i] is alloced by get_zeroed_page.
and kmemleak will not scan the area alloced by get_zeroed_page.
The address stored in elts->pages will be regarded as leaked.
That is, the elts->pages[i] will have pointers loaded onto it as well, and
without telling kmemleak about it, those pointers will look like memory
without a reference.
To fix this, call kmemleak_alloc to tell kmemleak to scan elts->pages[i]
Adding a check on len parameter to avoid empty skb. This prevents a
division error in netem_enqueue function which is caused when skb->len=0
and skb->data_len=0 in the randomized corruption step as shown below.
When link modes were initially added in commit 2c762679435dc
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d0eb
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221443
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch> Signed-off-by: Erik Ekman <erik@kryo.se> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "data_lanes" property of the dsi output endpoint is missing in
the DT, num_data_lanes would be 0 by default, which could cause
dsi_host_attach() to fail if dsi->lanes is set to a non-zero value
by the bridge driver.
According to the binding document of msm dsi controller, the
input/output endpoint of the controller is expected to have 4 lanes.
So let's set num_data_lanes to 4 by default.
According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers
Fixes: 292ec080491d ("irqchip: Add support for ARMv7-M NVIC") Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue") Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
When ACPI type is ACPI_SMO8500, the data->dready_trig will not be set, the
memory allocated by iio_triggered_buffer_setup() will not be freed, and cause
memory leak as follows:
Fix it by remove data->dready_trig condition in probe and remove.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: a25691c1f967 ("iio: accel: kxcjk1013: allow using an external trigger") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: <Stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211025124159.2700301-1-yangyingliang@huawei.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de961d ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs") Signed-off-by: Evgeny Boger <boger@wirenboard.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering a trigger can fail and the return value of
devm_iio_trigger_register() must be checked. Otherwise undefined behavior
can occur when the trigger is used.
Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20211101133043.6974-1-lars@metafoo.de Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce05691 ("iio: mma8452: Add support for interrupt driven triggers.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae18 ("staging:iio:triggers. Add a reference get to the core for triggers.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors") Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com> Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa873782 ("[PATCH] qla3xxx NIC driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211207082416.GA16110@kili Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd578 (net: fec: clear receive interrupts before processing a packet) Cc: Russell King <rmk+kernel@arm.linux.org.uk> Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org> Fixes: 289507d3364f9 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning") Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
do_each_pid_thread(PIDTYPE_PGID) can race with a concurrent
change_pid(PIDTYPE_PGID) that can move the task from one hlist
to another while iterating. Serialize ioprio_get to take
the tasklist_lock in this case, just like it's set counterpart.
As people have been asking to allow non-root processes to have access to
the tracefs directory, it was considered best to only allow groups to have
access to the directory, where it is easier to just set the tracefs file
system to a specific group (as other would be too dangerous), and that way
the admins could pick which processes would have access to tracefs.
Unfortunately, this broke tooling on Android that expected the other bit
to be set. For some special cases, for non-root tools to trace the system,
tracefs would be mounted and change the permissions of the top level
directory which gave access to all running tasks permission to the
tracing directory. Even though this would be dangerous to do in a
production environment, for testing environments this can be useful.
Now with the new changes to not allow other (which is still the proper
thing to do), it breaks the testing tooling. Now more code needs to be
loaded on the system to change ownership of the tracing directory.
The real solution is to have tracefs honor the gid=xxx option when
mounting. That is,
(tracing group tracing has value 1003)
mount -t tracefs -o gid=1003 tracefs /sys/kernel/tracing
should have it that all files in the tracing directory should be of the
given group.
Copy the logic from d_walk() from dcache.c and simplify it for the mount
case of tracefs if gid is set. All the files in tracefs will be walked and
their group will be set to the value passed in.
Link: https://lkml.kernel.org/r/20211207171729.2a54e1b3@gandalf.local.home Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-fsdevel@vger.kernel.org Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Kalesh Singh <kaleshsingh@google.com> Reported-by: Yabin Cui <yabinc@google.com> Fixes: 49d67e445742 ("tracefs: Have tracefs directories not set OTH permission bits by default") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wake_up_poll() uses nr_exclusive=1, so it's not guaranteed to wake up
all exclusive waiters. Yet, POLLFREE *must* wake up all waiters. epoll
and aio poll are fortunately not affected by this, but it's very
fragile. Thus, the new function wake_up_pollfree() has been introduced.
Convert signalfd to use wake_up_pollfree().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Fixes: d80e731ecab4 ("epoll: introduce POLLFREE to flush ->signalfd_wqh before kfree()") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211209010455.42744-4-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wake_up_poll() uses nr_exclusive=1, so it's not guaranteed to wake up
all exclusive waiters. Yet, POLLFREE *must* wake up all waiters. epoll
and aio poll are fortunately not affected by this, but it's very
fragile. Thus, the new function wake_up_pollfree() has been introduced.
Several ->poll() implementations are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, using 'wake_up_poll(wq, EPOLLHUP | POLLFREE);'.
However, that has a bug: wake_up_poll() calls __wake_up() with
nr_exclusive=1. Therefore, if there are multiple "exclusive" waiters,
and the wakeup function for the first one returns a positive value, only
that one will be called. That's *not* what's needed for POLLFREE;
POLLFREE is special in that it really needs to wake up everyone.
Considering the three non-blocking poll systems:
- io_uring poll doesn't handle POLLFREE at all, so it is broken anyway.
- aio poll is unaffected, since it doesn't support exclusive waits.
However, that's fragile, as someone could add this feature later.
- epoll doesn't appear to be broken by this, since its wakeup function
returns 0 when it sees POLLFREE. But this is fragile.
Although there is a workaround (see epoll), it's better to define a
function which always sends POLLFREE to all waiters. Add such a
function. Also make it verify that the queue really becomes empty after
all waiters have been woken up.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
After calling netif_receive_skb(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is dereferenced
just after the call netif_receive_skb(skb).
If directories in tracefs have their ownership changed, then any new files
and directories that are created under those directories should inherit
the ownership of the director they are created in.
Link: https://lkml.kernel.org/r/20211208075720.4855d180@gandalf.local.home Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Yabin Cui <yabinc@google.com> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: stable@vger.kernel.org Fixes: 4282d60689d4f ("tracefs: Add new tracefs file system") Reported-by: Kalesh Singh <kaleshsingh@google.com>
Reported: https://lore.kernel.org/all/CAC_TJve8MMAv+H_NdLSJXZUSoxOEq2zB_pVaJ9p=7H6Bu3X76g@mail.gmail.com/ Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A couple of calls in snd_pcm_oss_change_params_locked() ignore the
possible errors. Catch those errors and abort the operation for
avoiding further problems.
Set the practical limit to the period size (the fragment shift in OSS)
instead of a full 31bit; a too large value could lead to the exhaust
of memory as we allocate temporary buffers of the period size, too.
As of this patch, we set to 16MB limit, which should cover all use
cases.
The period size calculation in OSS layer may receive a negative value
as an error, but the code there assumes only the positive values and
handle them with size_t. Due to that, a too big value may be passed
to the lower layers.
This patch changes the code to handle with ssize_t and adds the proper
error checks appropriately.
When control_compat.c:copy_ctl_value_to_user() is used, by
ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the
snd_ctl_elem_id value that may have been updated (filled in) by the call
to snd_ctl_elem_read/snd_ctl_elem_write().
This matches the functionality provided by snd_ctl_elem_read_user() and
snd_ctl_elem_write_user(), via snd_ctl_build_ioff().
Without this, and without making additional calls to snd_ctl_info()
which are unnecessary when using the non-compat calls, a userspace
application will not know the numid value for the element and
consequently will not be able to use the poll/read interface on the
control file to determine which elements have updates.
Initialize min_ratio if it is set during bdi unregistration. This can
prevent problems that may occur a when bdi is removed without resetting
min_ratio.
For example.
1) insert external sdcard
2) set external sdcard's min_ratio 70
3) remove external sdcard without setting min_ratio 0
4) insert external sdcard
5) set external sdcard's min_ratio 70 << error occur(can't set)
Because when an sdcard is removed, the present bdi_min_ratio value will
remain. Currently, the only way to reset bdi_min_ratio is to reboot.
[akpm@linux-foundation.org: tweak comment and coding style]
Link: https://lkml.kernel.org/r/20211021161942.5983-1-mj0123.lee@samsung.com Signed-off-by: Manjong Lee <mj0123.lee@samsung.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Changheun Lee <nanich.lee@samsung.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: <seunghwan.hyun@samsung.com> Cc: <sookwan7.kim@samsung.com> Cc: <yt0928.kim@samsung.com> Cc: <junho89.kim@samsung.com> Cc: <jisoo2146.oh@samsung.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an IPv4 packet is received, the ip_rcv_core(...) sets the receiving
interface index into the IPv4 socket control block (v5.16-rc4,
net/ipv4/ip_input.c line 510):
IPCB(skb)->iif = skb->skb_iif;
If that IPv4 packet is meant to be encapsulated in an outer IPv6+SRH
header, the seg6_do_srh_encap(...) performs the required encapsulation.
In this case, the seg6_do_srh_encap function clears the IPv6 socket control
block (v5.16-rc4 net/ipv6/seg6_iptunnel.c line 163):
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
The memset(...) was introduced in commit ef489749aae5 ("ipv6: sr: clear
IP6CB(skb) on SRH ip4ip6 encapsulation") a long time ago (2019-01-29).
Since the IPv6 socket control block and the IPv4 socket control block share
the same memory area (skb->cb), the receiving interface index info is lost
(IP6CB(skb)->iif is set to zero).
As a side effect, that condition triggers a NULL pointer dereference if
commit 0857d6f8c759 ("ipv6: When forwarding count rx stats on the orig
netdev") is applied.
To fix that issue, we set the IP6CB(skb)->iif with the index of the
receiving interface once again.
Fixes: ef489749aae5 ("ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation") Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20211208195409.12169-1-andrea.mayer@uniroma2.it Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a
CPP area structure. But in line 807 (#2), when the cache is allocated
failed, this CPP area structure is not freed, which will result in
memory leak.
We can fix it by freeing the CPP area when the cache is allocated
failed (#2).
The first commit cited below attempts to fix the off-by-one error that
appeared in some comparisons with an open range. Due to this error,
arithmetically equivalent pieces of code could get different verdicts
from the verifier, for example (pseudocode):
// 1. Passes the verifier:
if (data + 8 > data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
// 2. Rejected by the verifier (should still pass):
if (data + 7 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The attempted fix, however, shifts the range by one in a wrong
direction, so the bug not only remains, but also such piece of code
starts failing in the verifier:
// 3. Rejected by the verifier, but the check is stricter than in #1.
if (data + 8 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The change performed by that fix converted an off-by-one bug into
off-by-two. The second commit cited below added the BPF selftests
written to ensure than code chunks like #3 are rejected, however,
they should be accepted.
This commit fixes the off-by-two error by adjusting new_range in the
right direction and fixes the tests by changing the range into the
one that should actually fail.
Fixes: fb2a311a31d3 ("bpf: fix off by one for range markings with L{T, E} patterns") Fixes: b37242c773b2 ("bpf: add test cases to bpf selftests to cover all access tests") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211130181607.593149-1-maximmi@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The done() netlink callback nfc_genl_dump_ses_done() should check if
received argument is non-NULL, because its allocation could fail earlier
in dumpit() (nfc_genl_dump_ses()).
Many HID drivers assume that the HID device assigned to them is a USB
device as that was the only way HID devices used to be able to be
created in Linux. However, with the additional ways that HID devices
can be created for many different bus types, that is no longer true, so
properly check that we have a USB device associated with the HID device
before allowing a driver that makes this assumption to claim it.
Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Michael Zaidman <michael.zaidman@gmail.com> Cc: Stefan Achatz <erazor_de@users.sourceforge.net> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: linux-input@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
[bentiss: amended for thrustmater.c hunk to apply] Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20211201183503.2373082-3-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wacom driver accepts devices of more than just USB types, but some
code paths can cause problems if the device being controlled is not a
USB device due to a lack of checking. Add the needed checks to ensure
that the USB device accesses are only happening on a "real" USB device,
and not one on some other bus.
Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: linux-input@vger.kernel.org Cc: stable@vger.kernel.org Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20211201183503.2373082-2-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some HID drivers are only for USB drivers, yet did not depend on
CONFIG_USB_HID. This was hidden by the fact that the USB functions were
stubbed out in the past, but now that drivers are checking for USB
devices properly, build errors can occur with some random
configurations.
The chicony HID driver only controls USB devices, yet did not have a
dependancy on USB_HID. This causes build errors on some configurations
like sparc when building due to new changes to the chicony driver.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: stable@vger.kernel.org Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20211203075927.2829218-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The prodikeys HID driver only controls USB devices, yet did not have a
dependancy on USB_HID. This causes build errors on some configurations
like nios2 when building due to new changes to the prodikeys driver.
Reported-by: kernel test robot <lkp@intel.com> Cc: stable@vger.kernel.org Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20211203081231.2856936-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of HID drivers already call hid_is_using_ll_driver() but only
for the detection of if this is a USB device or not. Make this more
obvious by creating hid_is_usb() and calling the function that way.
Also converts the existing hid_is_using_ll_driver() functions to use the
new call.
Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: linux-input@vger.kernel.org Cc: stable@vger.kernel.org Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20211201183503.2373082-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c8c3735997a3 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
projects / linux-stable / log