A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
Ziyang Xuan [Sat, 22 Jan 2022 10:25:06 +0000 (18:25 +0800)]
can: bcm: fix UAF of bcm op
Stopping tasklet and hrtimer rely on the active state of tasklet and
hrtimer sequentially in bcm_remove_op(), the op object will be freed
if they are all unactive. Assume the hrtimer timeout is short, the
hrtimer cb has been excuted after tasklet conditional judgment which
must be false after last round tasklet_kill() and before condition
hrtimer_active(), it is false when execute to hrtimer_active(). Bug
is triggerd, because the stopping action is end and the op object
will be freed, but the tasklet is scheduled. The resources of the op
object will occur UAF bug.
Move hrtimer_cancel() behind tasklet_kill() and switch 'while () {...}'
to 'do {...} while ()' to fix the op UAF problem.
Fixes: a06393ed0316 ("can: bcm: fix hrtimer/tasklet termination in bcm op removal") Reported-by: syzbot+5ca851459ed04c778d1d@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set up the connection to the NFSv4 server in nfs4_alloc_client(), before
we've added the struct nfs_client to the net-namespace's nfs_client_list
so that a downed server won't cause other mounts to hang in the trunking
detection code.
Reported-by: Michael Wakabayashi <mwakabayashi@vmware.com> Fixes: 5c6e5b60aae4 ("NFS: Fix an Oops in the pNFS files and flexfiles connection setup to the DS") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com> Signed-off-by: Jim Gruen <jgruen@spacex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d069dbe8aaf ("fuse: fix bad inode") replaced make_bad_inode()
in fuse_iget() with a private implementation fuse_make_bad().
The private implementation fails to remove the bad inode from inode
cache, so the retry loop with iget5_locked() finds the same bad inode
and marks it bad forever.
Jan Kara's analysis of the syzbot report (edited):
The reproducer opens a directory on FUSE filesystem, it then attaches
dnotify mark to the open directory. After that a fuse_do_getattr() call
finds that attributes returned by the server are inconsistent, and calls
make_bad_inode() which, among other things does:
inode->i_mode = S_IFREG;
This then confuses dnotify which doesn't tear down its structures
properly and eventually crashes.
Avoid calling make_bad_inode() on a live inode: switch to a private flag on
the fuse inode. Also add the test to ops which the bad_inode_ops would
have caught.
This bug goes back to the initial merge of fuse in 2.6.14...
Reported-by: syzbot+f427adf9324b92652ccc@syzkaller.appspotmail.com Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Jan Kara <jack@suse.cz> Cc: <stable@vger.kernel.org>
[bwh: Backported to 4.19:
- Drop changes in fuse_dir_fsync(), fuse_readahead(), fuse_evict_inode()
- In fuse_get_link(), return ERR_PTR(-EIO) for bad inodes
- Convert some additional calls to is_bad_inode()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is confusing, and from my reading of all the drivers only
nouveau got this right.
Just make the API act under driver control of it's own allocation
failing, and don't call destroy, if the page table fails to
create there is nothing to cleanup here.
(I'm willing to believe I've missed something here, so please
review deeply).
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200728041736.20689-1-airlied@gmail.com
[bwh: Backported to 4.14:
- Drop change in ttm_sg_tt_init()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 24 Jan 2022 15:11:18 +0000 (16:11 +0100)]
mips,s390,sh,sparc: gup: Work around the "COW can break either way" issue
In Linux 4.14 and 4.19 these architectures still have their own
implementations of get_user_pages_fast(). These also need to force
the write flag on when taking the fast path.
Fixes: 407faed92b4a ("gup: document and work around "COW can break either way" issue") Fixes: 5e24029791e8 ("gup: document and work around "COW can break either way" issue") Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 115978859272 ("i825xx: Move the Intel 82586/82593/82596 based drivers") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dtx_diff suggests to use <(...) syntax to pipe two inputs into it, but
this has never worked: The /proc/self/fds/... paths passed by the shell
will fail the `[ -f "${dtx}" ] && [ -r "${dtx}" ]` check in compile_to_dts,
but even with this check removed, the function cannot work: hexdump will
eat up the DTB magic, making the subsequent dtc call fail, as a pipe
cannot be rewound.
Simply remove this broken example, as there is already an alternative one
that works fine.
Fixes: 10eadc253ddf ("dtc: create tool to diff device trees") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220113081918.10387-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f267d ("net: bcmgenet: request Wake-on-LAN interrupt") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b765b79e9a ("htb: improved accuracy at high rates") broke
"overhead X", "linklayer atm" and "mpu X" attributes.
"overhead X" and "linklayer atm" have already been fixed. This restores
the "mpu X" handling, as might be used by DOCSIS or Ethernet shaping:
tc class add ... htb rate X overhead 4 mpu 64
The code being fixed is used by htb, tbf and act_police. Cake has its
own mpu handling. qdisc_calculate_pkt_len still uses the size table
containing values adjusted for mpu by user space.
iproute2 tc has always passed mpu into the kernel via a tc_ratespec
structure, but the kernel never directly acted on it, merely stored it
so that it could be read back by `tc class show`.
Rather, tc would generate length-to-time tables that included the mpu
(and linklayer) in their construction, and the kernel used those tables.
Since v3.7, the tables were no longer used. Along with "mpu", this also
broke "overhead" and "linklayer" which were fixed in 01cb71d2d47b
("net_sched: restore "overhead xxx" handling", v3.10) and 8a8e3d84b171
("net_sched: restore "linklayer atm" handling", v3.11).
"overhead" was fixed by simply restoring use of tc_ratespec::overhead -
this had originally been used by the kernel but was initially omitted
from the new non-table-based calculations.
"linklayer" had been handled in the table like "mpu", but the mode was
not originally passed in tc_ratespec. The new implementation was made to
handle it by getting new versions of tc to pass the mode in an extended
tc_ratespec, and for older versions of tc the table contents were analysed
at load time to deduce linklayer.
As "mpu" has always been given to the kernel in tc_ratespec,
accompanying the mpu-based table, we can restore system functionality
with no userspace change by making the kernel act on the tc_ratespec
value.
Fixes: 56b765b79e9a ("htb: improved accuracy at high rates") Signed-off-by: Kevin Bracey <kevin@bracey.fi> Cc: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Vimalkumar <j.vimal@gmail.com> Link: https://lore.kernel.org/r/20220112170210.1014351-1-kevin@bracey.fi Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware channel next descriptor view structure contains just
fields of 32 bits, while dma_addr_t can be of type u64 or u32
depending on CONFIG_ARCH_DMA_ADDR_T_64BIT. Force u32 to comply with
what the hardware expects.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove
at_xdmac_start_xfer() from at_xdmac_tx_submit(). Clients of at_xdmac that
assume that tx_submit() starts the transfer must be updated and call
dma_async_issue_pending() if they miss to call it (one example is
atmel_serial).
As the at_xdmac_start_xfer() is now called only from
at_xdmac_advance_work() when !at_xdmac_chan_is_enabled(), the
at_xdmac_chan_is_enabled() check is no longer needed in
at_xdmac_start_xfer(), thus remove it.
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
When under stress, cleanup_net() can have to dismantle
netns in big numbers. ops_exit_list() currently calls
many helpers [1] that have no schedule point, and we can
end up with soft lockups, particularly on hosts
with many cpus.
Even for moderate amount of netns processed by cleanup_net()
this patch avoids latency spikes.
[1] Some of these helpers like fib_sync_up() and fib_sync_down_dev()
are very slow because net/ipv4/fib_semantics.c uses host-wide hash tables,
and ifindex is used as the only input of two hash functions.
ifindexes tend to be the same for all netns (lo.ifindex==1 per instance)
This will be fixed in a separate patch.
Fixes: 72ad937abd0a ("net: Add support for batching network namespace cleanups") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_unix_gc() reads unix_tot_inflight & gc_in_progress
without synchronization.
Adds READ_ONCE()/WRITE_ONCE() and their associated comments
to better document the intent.
BUG: KCSAN: data-race in unix_inflight / wait_for_unix_gc
write to 0xffffffff86e2b7c0 of 4 bytes by task 9380 on cpu 0:
unix_inflight+0x1e8/0x260 net/unix/scm.c:63
unix_attach_fds+0x10c/0x1e0 net/unix/scm.c:121
unix_scm_to_skb net/unix/af_unix.c:1674 [inline]
unix_dgram_sendmsg+0x679/0x16b0 net/unix/af_unix.c:1817
unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
__do_sys_sendmmsg net/socket.c:2578 [inline]
__se_sys_sendmmsg net/socket.c:2575 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffffffff86e2b7c0 of 4 bytes by task 9375 on cpu 1:
wait_for_unix_gc+0x24/0x160 net/unix/garbage.c:196
unix_dgram_sendmsg+0x8e/0x16b0 net/unix/af_unix.c:1772
unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
__do_sys_sendmmsg net/socket.c:2578 [inline]
__se_sys_sendmmsg net/socket.c:2575 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000002 -> 0x00000004
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 9375 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
arch/powerpc/platforms/cell/pervasive.c:81:2: error: unannotated fall-through between switch labels
case SRR1_WAKEEE:
^
arch/powerpc/platforms/cell/pervasive.c:81:2: note: insert 'break;' to avoid fall-through
case SRR1_WAKEEE:
^
break;
1 error generated.
Clang is more pedantic than GCC, which does not warn when failing
through to a case that is just break or return. Clang's version is more
in line with the kernel's own stance in deprecated.rst. Add athe missing
break to silence the warning.
Fixes: 6e83985b0f6e ("powerpc/cbe: Do not process external or decremeter interrupts from sreset") Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211207110228.698956-1-anders.roxell@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The config RANDOMIZE_SLAB does not exist, the authors probably intended to
refer to the config RANDOMIZE_BASE, which provides kernel address-space
randomization. They probably just confused SLAB with BASE (these two
four-letter words coincidentally share three common letters), as they also
point out the config SLAB_FREELIST_RANDOM as further randomization within
the same sentence.
Fix the reference of the config for kernel address-space randomization to
the config that provides that.
Fixes: 6e88559470f5 ("Documentation: Add section about CPU vulnerabilities for Spectre") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20211230171940.27558-1-lukas.bulwahn@gmail.com Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The help text for GOOGLE_FIRMWARE states that it should only be
enabled when building a kernel for Google's own servers. However,
many of the drivers dependent on it are also useful on Chromebooks or
on any platform using coreboot.
Update the help text to reflect this double duty.
Fixes: d384d6f43d1e ("firmware: google memconsole: Add coreboot support") Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Link: https://lore.kernel.org/r/20180618225540.GD14131@decadent.org.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value was never initialized so the cleanup code executed when
it isn't even necessary.
Just add proper error handling.
Fixes: ab50cb9df889 ("drm/radeon/radeon_kms: Fix a NULL pointer dereference in radeon_driver_open_kms()") Signed-off-by: Christian König <christian.koenig@amd.com> Tested-by: Jan Stancek <jstancek@redhat.com> Tested-by: Borislav Petkov <bp@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The include/linux/crypto.h struct crypto_alg field cra_driver_name description
states "Unique name of the transformation provider. " ... " this contains the
name of the chip or provider and the name of the transformation algorithm."
In case of the stm32-crc driver, field cra_driver_name is identical for all
registered transformation providers and set to the name of the driver itself,
which is incorrect. This patch fixes it by assigning a unique cra_driver_name
to each registered transformation provider.
The kernel crash is triggered when the driver calls crypto_register_shashes()
which calls crypto_register_shash(), which calls crypto_register_alg(), which
calls __crypto_register_alg(), which returns -EEXIST, which is propagated
back through this call chain. Upon -EEXIST from crypto_register_shash(), the
crypto_register_shashes() starts unregistering the providers back, and calls
crypto_unregister_shash(), which calls crypto_unregister_alg(), and this is
where the BUG() triggers due to incorrect cra_refcnt.
Fixes: b51dbe90912a ("crypto: stm32 - Support for STM32 CRC32 crypto module") Signed-off-by: Marek Vasut <marex@denx.de> Cc: <stable@vger.kernel.org> # 4.12+ Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@st.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Lionel Debieve <lionel.debieve@st.com> Cc: Nicolas Toromanoff <nicolas.toromanoff@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-crypto@vger.kernel.org Acked-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We probably want to remove the indirect block to extents migration
feature after a deprecation window, but until then, let's fix a
potential data loss problem caused by the fact that we put the
tmp_inode on the orphan list. In the unlikely case where we crash and
do a journal recovery, the data blocks belonging to the inode being
migrated are also represented in the tmp_inode on the orphan list ---
and so its data blocks will get marked unallocated, and available for
reuse.
Instead, stop putting the tmp_inode on the oprhan list. So in the
case where we crash while migrating the inode, we'll leak an inode,
which is not a disaster. It will be easily fixed the next time we run
fsck, and it's better than potentially having blocks getting claimed
by two different files, and losing data as a result.
In order to reproduce this problem, the following conditions need to be met:
1. Ext4 filesystem with no journal;
2. Filesystem image with incorrect quota data;
3. Abort filesystem forced by user;
4. umount filesystem;
As in ext4_quota_write:
...
if (EXT4_SB(sb)->s_journal && !handle) {
ext4_msg(sb, KERN_WARNING, "Quota write (off=%llu, len=%llu)"
" cancelled because transaction is not started",
(unsigned long long)off, (unsigned long long)len);
return -EIO;
}
...
We only check handle if NULL when filesystem has journal. There is need
check handle if NULL even when filesystem has no journal.
Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20211223015506.297766-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When migrating to extents, the temporary inode will have it's own checksum
seed. This means that, when swapping the inodes data, the inode checksums
will be incorrect.
This can be fixed by recalculating the extents checksums again. Or simply
by copying the seed into the temporary inode.
When we hit an error when enabling quotas and setting inode flags, we do
not properly shutdown quota subsystem despite returning error from
Q_QUOTAON quotactl. This can lead to some odd situations like kernel
using quota file while it is still writeable for userspace. Make sure we
properly cleanup the quota subsystem in case of error.
With the introduction of 6GHz channels the scan guard timeout should
be adjusted to account for the following extreme case:
- All 6GHz channels are scanned passively: 58 channels.
- The scan is fragmented with the following parameters: 3 fragments,
95 TUs suspend time, 44 TUs maximal out of channel time.
The above would result with scan time of more than 24 seconds. Thus,
set the timeout to 30 seconds.
cpuacct.stat in no-root cgroups shows user time without guest time
included int it. This doesn't match with user time shown in root
cpuacct.stat and /proc/<pid>/stat. This also affects cgroup2's cpu.stat
in the same way.
Make account_guest_time() to add user time to cgroup's cpustat to
fix this.
Commit a6845e1e1b78 ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b78 ("serial: core: Consider rs485 settings to drive RTS") Cc: stable@vger.kernel.org # v4.14+ Cc: Rafael Gago Castano <rgc@hms.se> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Su Bao Cheng <baocheng.su@siemens.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Filesystem initially mounted read-only, free space fixup flag set.
2. mount -o remount,rw <mountpoint>
3. it takes some time (free space fixup running)
... try to terminate running mount by CTRL-C
... does not respond, only after free space fixup is complete
... then "ubifs_remount_fs: cannot spawn "ubifs_bgt0_0", error -4"
4. mount -o remount,rw <mountpoint>
... now finished instantly (fixup already done).
5. Create file or just unmount the filesystem and we get the oops.
Cc: <stable@vger.kernel.org> Fixes: b50b9f408502 ("UBIFS: do not free write-buffers when in R/O mode") Signed-off-by: Petr Cvachoucek <cvachoucek@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The allocated buffers are used as a command payload, for which the block
layer and/or DMA API do the proper bounce buffering if needed.
Link: https://lore.kernel.org/r/20211222090842.920724-1-hch@lst.de Reported-by: Baoquan He <bhe@redhat.com> Reviewed-by: Baoquan He <bhe@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A large number of the following errors is reported when compiling
with clang:
cvmx-bootinfo.h:326:3: error: adding 'int' to a string does not append to the string [-Werror,-Wstring-plus-int]
ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NULL)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
case x: return(#x + 16); /* Skip CVMX_BOARD_TYPE_ */
~~~^~~~
cvmx-bootinfo.h:326:3: note: use array indexing to silence this warning
cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
case x: return(#x + 16); /* Skip CVMX_BOARD_TYPE_ */
^
Follow the prompts to use the address operator '&' to fix this error.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was found by coccicheck:
./arch/mips/cavium-octeon/octeon-platform.c, 332, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 324, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-platform.c, 395, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 387, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 512, 3-9, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 543, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.
Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ALSA sequencer core tries to process the queued events as
much as possible when they become dispatchable. If applications try
to queue too massive events to be processed at the very same timing,
the sequencer core would still try to process such all events, either
in the interrupt context or via some notifier; in either away, it
might be a cause of RCU stall or such problems.
As a potential workaround for those problems, this patch adds the
upper limit of the amount of events to be processed. The remaining
events are processed in the next batch, so they won't be lost.
For the time being, it's limited up to 1000 events per queue, which
should be high enough for any normal usages.
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
setup_profiling_timer() is only needed when CONFIG_PROFILING is enabled.
Fixes the following W=1 warning when CONFIG_PROFILING=n:
linux/arch/powerpc/kernel/smp.c:1638:5: error: no previous prototype for ‘setup_profiling_timer’
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible for all CPUs to miss the pending cpumask becoming clear,
and then nobody resetting it, which will cause the lockup detector to
stop working. It will eventually expire, but watchdog_smp_panic will
avoid doing anything if the pending mask is clear and it will never be
reset.
Order the cpumask clear vs the subsequent test to close this race.
Add an extra check for an empty pending mask when the watchdog fires and
finds its bit still clear, to try to catch any other possible races or
bugs here and keep the watchdog working. The extra test in
arch_touch_nmi_watchdog is required to prevent the new warning from
firing off.
In handle_interruption(), we call faulthandler_disabled() to check whether the
fault handler is not disabled. If the fault handler is disabled, we immediately
call do_page_fault(). It then calls faulthandler_disabled(). If disabled,
do_page_fault() attempts to fixup the exception by jumping to no_context:
no_context:
if (!user_mode(regs) && fixup_exception(regs)) {
return;
}
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72b8 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr. At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr. However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens. Add an ASSERT() for the developers,
return -EUCLEAN for mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.
Blind cache flush on entering S5 causes problems for TDX.
Flushing happens with WBINVD that is not supported in the TDX
environment.
TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.
Link: https://github.com/acpica/acpica/commit/3dd7e1f3 Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.
This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS. For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.
Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.
Link: https://github.com/acpica/acpica/commit/d984f120 Link: https://github.com/acpica/acpica/pull/685 Reported-by: Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS. Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.
To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.
Link: https://github.com/acpica/acpica/commit/c11af67d Link: https://github.com/acpica/acpica/pull/652 Reported-by: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.
Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.
This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.
Link: https://github.com/acpica/acpica/commit/bc02c76d Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.
This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
- jffs2_write_begin() locks a cache page
- jffs2_write_end() tries to lock "alloc_sem" from
jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
- jffs2_garbage_collect_pass() locks "alloc_sem"
- try to lock the same cache page in read_cache_page() <-- STUCK
So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.
The function names init_registers() and restore_registers() are used
in several net/ethernet/ and gpu/drm/ drivers for other purposes (not
calls to UML functions), so rename them.
This fixes multiple build errors.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: linux-um@lists.infradead.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, iwlwifi crashes
when the opmode module cannot be loaded, due to completing
the completion before using drv->dev, which can then already
be freed.
Fix this by removing the (fairly useless) message. Moving the
completion later causes a deadlock instead, so that's not an
option.
If firmware load fails after having loaded some parts of the
firmware, e.g. the IML image, then this would leak. For the
host command list we'd end up running into a WARN on the next
attempt to load another firmware image.
Fix this by calling iwl_dealloc_ucode() on failures, and make
that also clear the data so we start fresh on the next round.
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of saa7146_register_device(). There is a dereference of
dev->vv_data in saa7146_vv_release(), which could lead to a NULL
pointer dereference on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_GEMINI=m show no new warnings,
and our static analyzer no longer warns about this code.
The WARN_ONCE() in bpf_warn_invalid_xdp_action() can be triggered by
any bugged program, and even attaching a correct program to a NIC
not supporting the given action.
The resulting splat, beyond polluting the logs, fouls automated tools:
e.g. a syzkaller reproducers using an XDP program returning an
unsupported action will never pass validation.
Replace the WARN_ONCE with a less intrusive pr_warn_once().
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
We need to check the max request size that is from user space before
allocating pages. If the request size exceeds the limit, return -EINVAL.
This check can avoid the warning below from page allocator.
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the configuration used by the b850v3, the STDP2690 is used to read EDID
data whilst it's the STDP4028 which can detect when monitors are connected.
This can result in problems at boot with monitors connected when the
STDP4028 is probed first, a monitor is detected and an attempt is made to
read the EDID data before the STDP2690 has probed:
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
A out-of-bounds bug can be triggered by an interrupt, the reason for
this bug is the lack of checking of register values.
In flexcop_pci_isr, the driver reads value from a register and uses it as
a dma address. Finally, this address will be passed to the count parameter
of find_next_packet. If this value is larger than the size of dma, the
index of buffer will be out-of-bounds.
Fix this by adding a check after reading the value of the register.
The following KASAN report reveals it:
BUG: KASAN: slab-out-of-bounds in find_next_packet
drivers/media/dvb-core/dvb_demux.c:528 [inline]
BUG: KASAN: slab-out-of-bounds in _dvb_dmx_swfilter
drivers/media/dvb-core/dvb_demux.c:572 [inline]
BUG: KASAN: slab-out-of-bounds in dvb_dmx_swfilter+0x3fa/0x420
drivers/media/dvb-core/dvb_demux.c:603
Read of size 1 at addr ffff8880608c00a0 by task swapper/2/0
Memory state around the buggy address: ffff8880608bff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880608c0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880608c0080: 00 00 00 00 fc fc fc fc fc fc fc fc 00 00 00 00
^ ffff8880608c0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880608c0180: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
projects / linux-stable / log