Ido Schimmel points out that since commit 52cff74eef5d ("dcbnl : Disable
software interrupts before taking dcb_lock"), the DCB API can be called
by drivers from softirq context.
One such in-tree example is the chelsio cxgb4 driver:
dcb_rpl
-> cxgb4_dcb_handle_fw_update
-> dcb_ieee_setapp
If the firmware for this driver happened to send an event which resulted
in a call to dcb_ieee_setapp() at the exact same time as another
DCB-enabled interface was unregistering on the same CPU, the softirq
would deadlock, because the interrupted process was already holding the
dcb_lock in dcbnl_flush_dev().
Fix this unlikely event by using spin_lock_bh() in dcbnl_flush_dev() as
in the rest of the dcbnl code.
Fixes: 91b0383fef06 ("net: dcb: flush lingering app table entries for unregistered devices") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220302193939.1368823-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the docker program tries to add F_SEAL_WRITE through the following
command, but it fails unexpectedly with errno EBUSY:
fcntl(5, F_ADD_SEALS, F_SEAL_WRITE) = -1.
That is because memfd_tag_pins() and memfd_wait_for_pins() were never
updated for shmem huge pages: checking page_mapcount() against
page_count() is hopeless on THP subpages - they need to check
total_mapcount() against page_count() on THP heads only.
Make memfd_tag_pins() (compared > 1) as strict as memfd_wait_for_pins()
(compared != 1): either can be justified, but given the non-atomic
total_mapcount() calculation, it is better now to be strict. Bear in
mind that total_mapcount() itself scans all of the THP subpages, when
choosing to take an XA_CHECK_SCHED latency break.
Also fix the unlikely xa_is_value() case in memfd_wait_for_pins(): if a
page has been swapped out since memfd_tag_pins(), then its refcount must
have fallen, and so it can safely be untagged.
Link: https://lkml.kernel.org/r/a4f79248-df75-2c8c-3df-ba3317ccb5da@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Zeal Robot <zealci@zte.com.cn> Reported-by: wangyong <wang.yong12@zte.com.cn> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: CGEL ZTE <cgel.zte@gmail.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Song Liu <songliubraving@fb.com> Cc: Yang Yang <yang.yang29@zte.com.cn> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()] Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function pci_find_capability() in t3_prep_adapter() can fail, so its
return value should be checked.
Fixes: 4d22de3e6cc4 ("Add support for the latest 1G/10G Chelsio adapter, T3") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the possible failure of the ioremap(), the par_io could be NULL.
Therefore it should be better to check it and return error in order to
guarantee the success of the initiation.
But, I also notice that all the caller like mpc85xx_qe_par_io_init() in
`arch/powerpc/platforms/85xx/common.c` don't check the return value of
the par_io_init().
Actually, par_io_init() needs to check to handle the potential error.
I will submit another patch to fix that.
Anyway, par_io_init() itsely should be fixed.
Fixes: 7aa1aa6ecec2 ("QE: Move QE from arch/powerpc to drivers/soc") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
early_param() handlers should return 0 on success.
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 would cause the "option=value" string
to be added to init's environment strings, polluting it.
../arch/arm/mm/mmu.c: In function 'test_early_cachepolicy':
../arch/arm/mm/mmu.c:215:1: error: no return statement in function returning non-void [-Werror=return-type]
../arch/arm/mm/mmu.c: In function 'test_noalign_setup':
../arch/arm/mm/mmu.c:221:1: error: no return statement in function returning non-void [-Werror=return-type]
Fixes: b849a60e0903 ("ARM: make cr_alignment read-only #ifndef CONFIG_CPU_CP15") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: patches@armlinux.org.uk Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses an atomic_t variable: gs_usb:active_channels to keep
track of the number of opened channels in order to only allocate
memory for the URBs when this count changes from zero to one.
However, the driver does not decrement the counter when an error
occurs in gs_can_open(). This issue is fixed by changing the type from
atomic_t to u8 and by simplifying the logic accordingly.
It is safe to use an u8 here because the network stack big kernel lock
(a.k.a. rtnl_mutex) is being hold. For details, please refer to [1].
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Link: https://lore.kernel.org/all/20220214234814.1321599-1-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the "block" flag is false, the old code would sometimes still call
check_var_size(), which wrongly tells ->query_variable_store() that it can
block.
As far as I can tell, this can't really materialize as a bug at the moment,
because ->query_variable_store only does something on X86 with generic EFI,
and in that configuration we always take the efivar_entry_set_nonblocking()
path.
During driver initialization, the pointer of card info, i.e. the
variable 'ci' is required. However, the definition of
'com20020pci_id_table' reveals that this field is empty for some
devices, which will cause null pointer dereference when initializing
these devices.
Fix this by checking whether the 'ci' is a null pointer first.
Fixes: 8c14f9c70327 ("ARCNET: add com20020 PCI IDs with metadata") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: acc18c147b22 ("net: sxgbe: add EEE(Energy Efficient Ethernet) for Samsung sxgbe") Fixes: 1edb9ca69e8a ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Siva Reddy <siva.kallam@samsung.com> Cc: Girish K S <ks.giri@samsung.com> Cc: Byungho An <bh74.an@samsung.com> Link: https://lore.kernel.org/r/20220224033528.24640-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.") Fixes: f3240e2811f0 ("stmmac: remove warning when compile as built-in (V2)") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Jose Abreu <joabreu@synopsys.com> Link: https://lore.kernel.org/r/20220224033536.25056-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two problems with the current code that have been highlighted
with the AQL feature that is now enbaled by default.
First problem is in ieee80211_rx_h_mesh_fwding(),
ieee80211_select_queue_80211() is used on received packets to choose
the sending AC queue of the forwarding packet although this function
should only be called on TX packet (it uses ieee80211_tx_info).
This ends with forwarded mesh packets been sent on unrelated random AC
queue. To fix that, AC queue can directly be infered from skb->priority
which has been extracted from QOS info (see ieee80211_parse_qos()).
Second problem is the value of queue_mapping set on forwarded mesh
frames via skb_set_queue_mapping() is not the AC of the packet but a
hardware queue index. This may or may not work depending on AC to HW
queue mapping which is driver specific.
Both of these issues lead to improper AC selection while forwarding
mesh packets but more importantly due to improper airtime accounting
(which is done on a per STA, per AC basis) caused traffic stall with
the introduction of AQL.
An initialised kobject must be freed using kobject_put() to avoid
leaking associated resources (e.g. the object name).
Commit fe3c60684377 ("firmware: Fix a reference count leak.") "fixed"
the leak in the first error path of the file registration helper but
left the second one unchanged. This "fix" would however result in a NULL
pointer dereference due to the release function also removing the never
added entry from the fw_cfg_entry_cache list. This has now been
addressed.
Fix the remaining kobject leak by restoring the common error path and
adding the missing kobject_put().
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Callback function fw_cfg_sysfs_release_entry() in kobject_put()
can handle the pointer "entry" properly.
The problem of SMC_CLC_DECL_ERR_REGRMB on the server is very clear.
Based on the fact that whether a new SMC connection can be accepted or
not depends on not only the limit of conn nums, but also the available
entries of rtoken. Since the rtoken release is trigger by peer, while
the conn nums is decrease by local, tons of thing can happen in this
time difference.
This only thing that needs to be mentioned is that now all connection
creations are completely protected by smc_server_lgr_pending lock, it's
enough to check only the available entries in rtokens_used_mask.
Fixes: cd6851f30386 ("smc: remote memory buffers (RMBs)") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
smc_lgr_unregister_conn() makes current link available to assigned to new
incoming connection, while smcr_buf_unuse() has not executed yet, which
means that smc_rtoken_add may fail because of insufficient rtoken_entry,
reversing their execution order will avoid this problem.
Fixes: 3e034725c0d8 ("net/smc: common functions for RMBs and send buffers") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If I'm not mistaken (and I don't think I am), the way in which the
dcbnl_ops work is that drivers call dcb_ieee_setapp() and this populates
the application table with dynamically allocated struct dcb_app_type
entries that are kept in the module-global dcb_app_list.
However, nobody keeps exact track of these entries, and although
dcb_ieee_delapp() is supposed to remove them, nobody does so when the
interface goes away (example: driver unbinds from device). So the
dcb_app_list will contain lingering entries with an ifindex that no
longer matches any device in dcb_app_lookup().
Reclaim the lost memory by listening for the NETDEV_UNREGISTER event and
flushing the app table entries of interfaces that are now gone.
In fact something like this used to be done as part of the initial
commit (blamed below), but it was done in dcbnl_exit() -> dcb_flushapp(),
essentially at module_exit time. That became dead code after commit 7a6b6f515f77 ("DCB: fix kconfig option") which essentially merged
"tristate config DCB" and "bool config DCBNL" into a single "bool config
DCB", so net/dcb/dcbnl.c could not be built as a module anymore.
Commit 36b9ad8084bd ("net/dcb: make dcbnl.c explicitly non-modular")
recognized this and deleted dcbnl_exit() and dcb_flushapp() altogether,
leaving us with the version we have today.
Since flushing application table entries can and should be done as soon
as the netdevice disappears, fundamentally the commit that is to blame
is the one that introduced the design of this API.
Fixes: 9ab933ab2cc8 ("dcbnl: add appliction tlv handlers") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi") Reported-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct xfrm_user_offload has flags variable that received user input,
but kernel didn't check if valid bits were provided. It caused a situation
where not sanitized input was forwarded directly to the drivers.
For example, XFRM_OFFLOAD_IPV6 define that was exposed, was used by
strongswan, but not implemented in the kernel at all.
As a solution, check and sanitize input flags to forward
XFRM_OFFLOAD_INBOUND to the drivers.
We must not dereference @new_hooks after nf_hook_mutex has been released,
because other threads might have freed our allocated hooks already.
BUG: KASAN: use-after-free in nf_hook_entries_get_hook_ops include/linux/netfilter.h:130 [inline]
BUG: KASAN: use-after-free in hooks_validate net/netfilter/core.c:171 [inline]
BUG: KASAN: use-after-free in __nf_register_net_hook+0x77a/0x820 net/netfilter/core.c:438
Read of size 2 at addr ffff88801c1a8000 by task syz-executor237/4430
A Packet Too Big ICMPv6 message received in response to an ESP
packet will prevent all further communication through the tunnel
if the reported MTU minus the ESP overhead is smaller than 1280.
E.g. in a case of a tunnel-mode ESP with sha256/aes the overhead
is 92 bytes. Receiving a PTB with MTU of 1371 or less will result
in all further packets in the tunnel dropped. A ping through the
tunnel fails with "ping: sendmsg: Invalid argument".
Apparently the MTU on the xfrm route is smaller than 1280 and
fails the check inside ip6_setup_cork() added by 749439bf.
We found this by debugging USGv6/ipv6ready failures. Failing
tests are: "Phase-2 Interoperability Test Scenario IPsec" /
5.3.11 and 5.4.11 (Tunnel Mode: Fragmentation).
Commit b515d2637276a3810d6595e10ab02c13bfd0b63a ("xfrm:
xfrm_state_mtu should return at least 1280 for ipv6") attempted
to fix this but caused another regression in TCP MSS calculations
and had to be reverted.
The patch below fixes the situation by dropping the MTU
check and instead checking for the underflows described in the 749439bf commit message.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Fixes: 749439bfac6e ("ipv6: fix udpv6 sendmsg crash caused by too small MTU") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the $val/$val2 values passed in from userspace are always >= 0
integers, the limits of the control can be signed integers and the $min
can be non-zero and less than zero. To correctly validate $val/$val2
against platform_max, add the $min offset to val first.
Fixes: 817f7c9335ec0 ("ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220215130645.164025-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCM buffers might be allocated dynamically when the buffer
preallocation failed or a larger buffer is requested, and it's not
guaranteed that substream->dma_buffer points to the actually used
buffer. The driver needs to refer to substream->runtime->dma_addr
instead for the buffer address.
pm_runtime_get_() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
When cifs_get_root() fails during cifs_smb3_do_mount() we call
deactivate_locked_super() which eventually will call delayed_free() which
will free the context.
In this situation we should not proceed to enter the out: section in
cifs_smb3_do_mount() and free the same resources a second time.
[Thu Feb 10 12:59:06 2022] BUG: KASAN: use-after-free in rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] Read of size 8 at addr ffff888364f4d110 by task swapper/1/0
[Thu Feb 10 12:59:06 2022] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G OE 5.17.0-rc3+ #4
[Thu Feb 10 12:59:06 2022] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
[Thu Feb 10 12:59:06 2022] Call Trace:
[Thu Feb 10 12:59:06 2022] <IRQ>
[Thu Feb 10 12:59:06 2022] dump_stack_lvl+0x5d/0x78
[Thu Feb 10 12:59:06 2022] print_address_description.constprop.0+0x24/0x150
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] kasan_report.cold+0x7d/0x117
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] __asan_load8+0x86/0xa0
[Thu Feb 10 12:59:06 2022] rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] rcu_core+0x547/0xca0
[Thu Feb 10 12:59:06 2022] ? call_rcu+0x3c0/0x3c0
[Thu Feb 10 12:59:06 2022] ? __this_cpu_preempt_check+0x13/0x20
[Thu Feb 10 12:59:06 2022] ? lock_is_held_type+0xea/0x140
[Thu Feb 10 12:59:06 2022] rcu_core_si+0xe/0x10
[Thu Feb 10 12:59:06 2022] __do_softirq+0x1d4/0x67b
[Thu Feb 10 12:59:06 2022] __irq_exit_rcu+0x100/0x150
[Thu Feb 10 12:59:06 2022] irq_exit_rcu+0xe/0x30
[Thu Feb 10 12:59:06 2022] sysvec_hyperv_stimer0+0x9d/0xc0
...
[Thu Feb 10 12:59:07 2022] Freed by task 58179:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] kasan_set_track+0x25/0x30
[Thu Feb 10 12:59:07 2022] kasan_set_free_info+0x24/0x40
[Thu Feb 10 12:59:07 2022] ____kasan_slab_free+0x137/0x170
[Thu Feb 10 12:59:07 2022] __kasan_slab_free+0x12/0x20
[Thu Feb 10 12:59:07 2022] slab_free_freelist_hook+0xb3/0x1d0
[Thu Feb 10 12:59:07 2022] kfree+0xcd/0x520
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0x149/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thu Feb 10 12:59:07 2022] Last potentially related work creation:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] __kasan_record_aux_stack+0xb6/0xc0
[Thu Feb 10 12:59:07 2022] kasan_record_aux_stack_noalloc+0xb/0x10
[Thu Feb 10 12:59:07 2022] call_rcu+0x76/0x3c0
[Thu Feb 10 12:59:07 2022] cifs_umount+0xce/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] cifs_kill_sb+0xc8/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] deactivate_locked_super+0x5d/0xd0
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0xab9/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: José Expósito <jose.exposito89@gmail.com> Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> BugLink: https://github.com/raspberrypi/linux/issues/3064 Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mac80211_hwsim, the probe_req frame is created and sent while
scanning. It is sent with ieee80211_tx_info which is not initialized.
Uninitialized ieee80211_tx_info can cause problems when using
mac80211_hwsim with wmediumd. wmediumd checks the tx_rates field of
ieee80211_tx_info and doesn't relay probe_req frame to other clients
even if it is a broadcasting message.
Call ieee80211_tx_prepare_skb() to initialize ieee80211_tx_info for
the probe_req that is created by hw_scan_work in mac80211_hwsim.
Commit 054aa8d439b9 ("fget: check that the fd still exists after getting
a ref to it") fixed a race with getting a reference to a file just as it
was being closed. It was a fairly minimal patch, and I didn't think
re-checking the file pointer lookup would be a measurable overhead,
since it was all right there and cached.
But I was wrong, as pointed out by the kernel test robot.
The 'poll2' case of the will-it-scale.per_thread_ops benchmark regressed
quite noticeably. Admittedly it seems to be a very artificial test:
doing "poll()" system calls on regular files in a very tight loop in
multiple threads.
That means that basically all the time is spent just looking up file
descriptors without ever doing anything useful with them (not that doing
'poll()' on a regular file is useful to begin with). And as a result it
shows the extra "re-check fd" cost as a sore thumb.
Happily, the regression is fixable by just writing the code to loook up
the fd to be better and clearer. There's still a cost to verify the
file pointer, but now it's basically in the noise even for that
benchmark that does nothing else - and the code is more understandable
and has better comments too.
[ Side note: this patch is also a classic case of one that looks very
messy with the default greedy Myers diff - it's much more legible with
either the patience of histogram diff algorithm ]
memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Fixes: 3010f876500f ("mm: discard memblock data later") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older stable branches backporting this commit is complicated as relevant
code changed quite a bit. Furthermore most of the affected hardware barely
works on those and users would want to use the newer kernels anyway.
Cc: stable@vger.kernel.org # 5.4 4.19 and 4.14 Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Lyude Paul <lyude@redhat.com> Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/149 Signed-off-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Dell DW5829e same as DW5821e except CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
There are 2 types product of DW5829e: normal and eSIM.
So we will add 2 PID for DW5829e.
And for each PID, it support MBIM or RMNET.
Let's see test evidence as below:
BTW, the interface 0x6 of MBIM mode is GNSS port, which not same as NMEA
port. So it's banned from serial option driver.
The remaining interfaces 0x2-0x5 are: MODEM, MODEM, NMEA, DIAG.
Signed-off-by: Slark Xiao <slark_xiao@163.com> Link: https://lore.kernel.org/r/20220214021401.6264-1-slark_xiao@163.com
[ johan: drop unnecessary reservation of interface 1 ] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro brought it to my attention that the dentries may not be filled
when the parse_options() is called, causing the call to set_gid() to
possibly crash. It should only be called if parse_options() succeeds
totally anyway.
He suggested the logical place to do the update is in apply_options().
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
CH341 has Product ID 0x5512 in EPP/MEM mode which is used for
I2C/SPI/GPIO interfaces. In asynchronous serial interface mode
CH341 has PID 0x5523 which is already in the table.
The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.
Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.") Cc: stable@vger.kernel.org Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the flush_workqueue(system_long_wq) call since flushing
system_long_wq is deadlock-prone and since that call is redundant with a
preceding cancel_work_sync()
Link: https://lore.kernel.org/r/20220215210511.28303-3-bvanassche@acm.org Fixes: ef6c49d87c34 ("IB/srp: Eliminate state SRP_TARGET_DEAD") Reported-by: syzbot+831661966588c802aae9@syzkaller.appspotmail.com Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.
One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D
Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex.
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71ad8 ("drm: parse color format support for digital displays") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-by: Matthias Reichl <hias@horus.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a70b ("ipip: add GSO/TSO support") Signed-off-by: Tao Liu <thomas.liu@ucloud.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: Ross Maynard <bids.7405@bigpond.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usually the kernel provides fixup routines to emulate the fldd and fstd
floating-point instructions if they load or store 8-byte from/to a not
natuarally aligned memory location.
On a 32-bit kernel I noticed that those unaligned handlers didn't worked and
instead the application got a SEGV.
While checking the code I found two problems:
First, the OPCODE_FLDD_L and OPCODE_FSTD_L cases were ifdef'ed out by the
CONFIG_PA20 option, and as such those weren't built on a pure 32-bit kernel.
This is now fixed by moving the CONFIG_PA20 #ifdef to prevent the compilation
of OPCODE_LDD_L and OPCODE_FSTD_L only, and handling the fldd and fstd
instructions.
The second problem are two bugs in the 32-bit inline assembly code, where the
wrong registers where used. The calculation of the natural alignment used %2
(vall) instead of %3 (ior), and the first word was stored back to address %1
(valh) instead of %3 (ior).
vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.
vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.
Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.
When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko") Cc: stable@vger.kernel.org Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As previously discussed(https://lkml.org/lkml/2022/1/20/51),
cpuset_attach() is affected with similar cpu hotplug race,
as follow scenario:
cpuset_attach() cpu hotplug
--------------------------- ----------------------
down_write(cpuset_rwsem)
guarantee_online_cpus() // (load cpus_attach)
sched_cpu_deactivate
set_cpu_active()
// will change cpu_active_mask
set_cpus_allowed_ptr(cpus_attach)
__set_cpus_allowed_ptr_locked()
// (if the intersection of cpus_attach and
cpu_active_mask is empty, will return -EINVAL)
up_write(cpuset_rwsem)
To avoid races such as described above, protect cpuset_attach() call
with cpu_hotplug_lock.
Fixes: be367d099270 ("cgroups: let ss->can_attach and ss->attach do whole threadgroups at a time") Cc: stable@vger.kernel.org # v2.6.32+ Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com> Acked-by: Waiman Long <longman@redhat.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dell DW5829e same as DW5821e except the CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
Also, DW5829e includes normal and eSIM type.
Please see below test evidence:
The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.
This is similar to other kernel parameter issues, such as:
Commit 745a600cf1a6 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)
Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.
Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix following coccicheck warning:
./arch/arm/mach-omap2/omap_hwmod.c:753:1-23: WARNING: Function
for_each_matching_node should have of_node_put() before break
Early exits from for_each_matching_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The result of the writeback, whether it is an ENOSPC or an EIO, or
anything else, does not inhibit the NFS client from reporting the
correct file timestamps.
AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't mask off the high nybble when configuring a
RAW perf event.
Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM") Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-2-jmattson@google.com> Reviewed-by: David Dunn <daviddunn@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
The functions copy_page_to_iter_pipe() and push_pipe() can both
allocate a new pipe_buffer, but the "flags" member initializer is
missing.
Fixes: 241699cd72a8 ("new iov_iter flavour: pipe-backed")
To: Alexander Viro <viro@zeniv.linux.org.uk>
To: linux-fsdevel@vger.kernel.org
To: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Max Kellermann <max.kellermann@ionos.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Do alignment logic properly and use the "ptr" local variable for
calculating the remainder of the alignment.
This became an issue because struct edac_mc_layer has a size that is not
zero modulo eight, and the next offset that was prepared for the private
data was unaligned, causing an alignment exception.
The patch in Fixes: which broke this actually wanted to "what we
actually care about is the alignment of the actual pointer that's about
to be returned." But it didn't check that alignment.
Commit ac795161c936 (NFSv4: Handle case where the lookup of a directory
fails) [1], part of Linux since 5.17-rc2, introduced a regression, where
a symbolic link on an NFS mount to a directory on another NFS does not
resolve(?) the first time it is accessed:
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Fixes: ac795161c936 ("NFSv4: Handle case where the lookup of a directory fails") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Tested-by: Donald Buczek <buczek@molgen.mpg.de> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the 'ifdef CONFIG_PPC64' around the 'ptesync' in function
'emulate_update_regs()' to like it is in 'analyse_instr()'. Since it looks like
it got dropped inadvertently by commit 3cdfcbfd32b9 ("powerpc: Change
analyse_instr so it doesn't modify *regs").
A key detail is that analyse_instr() will never recognise lwsync or
ptesync on 32-bit (because of the existing ifdef), and as a result
emulate_update_regs() should never be called with an op specifying
either of those on 32-bit. So removing them from emulate_update_regs()
should be a nop in terms of runtime behaviour.
Fixes: 3cdfcbfd32b9 ("powerpc: Change analyse_instr so it doesn't modify *regs") Cc: stable@vger.kernel.org # v4.14+ Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[mpe: Add last paragraph of change log mentioning analyse_instr() details] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220211005113.1361436-1-anders.roxell@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.
When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.
By some unknown reason, BIOS on Shenker Dock 15 doesn't set up the
codec mask properly for the onboard audio. Let's set the forced codec
mask to enable the codec discovery.
The forced probe mask via probe_mask 0x100 bit doesn't work any longer
as expected since the bus init code was moved and it's clearing the
codec_mask value that was set beforehand. This patch fixes the
long-time regression by moving the check_probe_mask() call.
GCC 12 correctly reports a potential use-after-free condition in the
xrealloc helper. Fix the warning by avoiding an implicit "free(ptr)"
when size == 0:
In file included from help.c:12:
In function 'xrealloc',
inlined from 'add_cmdname' at help.c:24:2: subcmd-util.h:56:23: error: pointer may be used after 'realloc' [-Werror=use-after-free]
56 | ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:58:31: error: pointer may be used after 'realloc' [-Werror=use-after-free]
58 | ret = realloc(ptr, 1);
| ^~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
syzbot reported that two threads might write over agg_select_timer
at the same time. Make agg_select_timer atomic to fix the races.
BUG: KCSAN: data-race in bond_3ad_initiate_agg_selection / bond_3ad_state_machine_handler
read to 0xffff8881242aea90 of 4 bytes by task 1846 on cpu 1:
bond_3ad_state_machine_handler+0x99/0x2810 drivers/net/bonding/bond_3ad.c:2317
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25910 Comm: syz-executor.1 Tainted: G W 5.17.0-rc4-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()
Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.
BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit
write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
notifier_call_chain kernel/notifier.c:84 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
call_netdevice_notifiers net/core/dev.c:1945 [inline]
unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
ops_exit_list net/core/net_namespace.c:173 [inline]
cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
trace_napi_poll include/trace/events/napi.h:14 [inline]
__napi_poll+0x36b/0x3f0 net/core/dev.c:6366
napi_poll net/core/dev.c:6432 [inline]
net_rx_action+0x29e/0x650 net/core/dev.c:6519
__do_softirq+0x158/0x2de kernel/softirq.c:558
do_softirq+0xb1/0xf0 kernel/softirq.c:459
__local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:394 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0xffff88815883e000 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker
Fixes: 4ea7e38696c7 ("dropmon: add ability to detect when hardware dropsrxpackets") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log