The Counter (CNTR) register is 24 bits wide, but we can have an
effective 25-bit count value by setting bit 24 to the XOR of the Borrow
flag and Carry flag. The flags can be read from the FLAG register, but a
race condition exists: the Borrow flag and Carry flag are instantaneous
and could change by the time the count value is read from the CNTR
register.
Since the race condition could result in an incorrect 25-bit count
value, remove support for 25-bit count values from this driver;
hard-coded maximum count values are replaced by a LS7267_CNTR_MAX define
for consistency and clarity.
Fixes: 28e5d3bb0325 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8") Cc: <stable@vger.kernel.org> # 6.1.x Cc: <stable@vger.kernel.org> # 6.2.x Link: https://lore.kernel.org/r/20230312231554.134858-1-william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
SCTP sets its own sk->sk_destruct() in the sctp_init_sock(), and
SCTPv6 socket reuses it as the init function.
To call inet6_sock_destruct() from SCTPv6 sk->sk_destruct(), we
set sctp_v6_destruct_sock() in a new init function.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
DCCP sets its own sk->sk_destruct() in the dccp_init_sock(), and
DCCPv6 socket shares it by calling the same init function via
dccp_v6_init_sock().
To call inet6_sock_destruct() from DCCPv6 sk->sk_destruct(), we
export it and set dccp_v6_sk_destruct() in the init function.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
Now we can remove unnecessary inet6_destroy_sock() calls in
sk->sk_prot->destroy().
DCCP and SCTP have their own sk->sk_destruct() function, so we
change them separately in the following patches.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, inet6_sk(sk)->XXX were changed under lock_sock(), so we were
able to clean them up by calling inet6_destroy_sock() during the IPv6 ->
IPv4 conversion by IPV6_ADDRFORM. However, commit 03485f2adcde ("udpv6:
Add lockless sendmsg() support") added a lockless memory allocation path,
which could cause a memory leak:
setsockopt(IPV6_ADDRFORM) sendmsg()
+-----------------------+ +-------+
- do_ipv6_setsockopt(sk, ...) - udpv6_sendmsg(sk, ...)
- sockopt_lock_sock(sk) ^._ called via udpv6_prot
- lock_sock(sk) before WRITE_ONCE()
- WRITE_ONCE(sk->sk_prot, &tcp_prot)
- inet6_destroy_sock() - if (!corkreq)
- sockopt_release_sock(sk) - ip6_make_skb(sk, ...)
- release_sock(sk) ^._ lockless fast path for
the non-corking case
- __ip6_append_data(sk, ...)
- ipv6_local_rxpmtu(sk, ...)
- xchg(&np->rxpmtu, skb)
^._ rxpmtu is never freed.
- goto out_no_dst;
- lock_sock(sk)
For now, rxpmtu is only the case, but not to miss the future change
and a similar bug fixed in commit e27326009a3d ("net: ping6: Fix
memleak in ipv6_renew_options()."), let's set a new function to IPv6
sk->sk_destruct() and call inet6_cleanup_sock() there. Since the
conversion does not change sk->sk_destruct(), we can guarantee that
we can clean up IPv6 resources finally.
We can now remove all inet6_destroy_sock() calls from IPv6 protocol
specific ->destroy() functions, but such changes are invasive to
backport. So they can be posted as a follow-up later for net-next.
Commit 4b340ae20d0e ("IPv6: Complete IPV6_DONTFRAG support") forgot
to add a change to free inet6_sk(sk)->rxpmtu while converting an IPv6
socket into IPv4 with IPV6_ADDRFORM. After conversion, sk_prot is
changed to udp_prot and ->destroy() never cleans it up, resulting in
a memory leak.
This is due to the discrepancy between inet6_destroy_sock() and
IPV6_ADDRFORM, so let's call inet6_destroy_sock() from IPV6_ADDRFORM
to remove the difference.
However, this is not enough for now because rxpmtu can be changed
without lock_sock() after commit 03485f2adcde ("udpv6: Add lockless
sendmsg() support"). We will fix this case in the following patch.
Note we will rename inet6_destroy_sock() to inet6_cleanup_sock() and
remove unnecessary inet6_destroy_sock() calls in sk_prot->destroy()
in the future.
Hulk Robot reported a issue:
==================================================================
BUG: KASAN: use-after-free in ext4_xattr_set_entry+0x18ab/0x3500
Write of size 4105 at addr ffff8881675ef5f4 by task syz-executor.0/7092
Above issue may happen as follows:
-------------------------------------
ext4_xattr_set
ext4_xattr_set_handle
ext4_xattr_ibody_find
>> s->end < s->base
>> no EXT4_STATE_XATTR
>> xattr_check_inode is not executed
ext4_xattr_ibody_set
ext4_xattr_set_entry
>> size_t min_offs = s->end - s->base
>> UAF in memcpy
we can easily reproduce this problem with the following commands:
mkfs.ext4 -F /dev/sda
mount -o debug_want_extra_isize=128 /dev/sda /mnt
touch /mnt/file
setfattr -n user.cat -v `seq -s z 4096|tr -d '[:digit:]'` /mnt/file
In ext4_xattr_ibody_find, we have the following assignment logic:
header = IHDR(inode, raw_inode)
= raw_inode + EXT4_GOOD_OLD_INODE_SIZE + i_extra_isize
is->s.base = IFIRST(header)
= header + sizeof(struct ext4_xattr_ibody_header)
is->s.end = raw_inode + s_inode_size
In the calculation formula, all values except s_inode_size and
i_extra_size are fixed values. When i_extra_size is the maximum value
s_inode_size - EXT4_GOOD_OLD_INODE_SIZE, min_offs is -4 and free is -8.
The value overflows. As a result, the preceding issue is triggered when
memcpy is executed.
Therefore, when finding xattr or setting xattr, check whether
there is space for storing xattr in the inode to resolve this issue.
Cc: stable@kernel.org Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220616021358.2504451-3-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ext4_xattr_ibody_inline_set() & ext4_xattr_ibody_set() have the exact
same definition. Hence remove ext4_xattr_ibody_inline_set() and all
its call references. Convert the callers of it to call
ext4_xattr_ibody_set() instead.
[ Modified to preserve ext4_xattr_ibody_set() and remove
ext4_xattr_ibody_inline_set() instead. -- TYT ]
The order in which patches are queued to stable matters. This patch
has a logical dependency on commit 310c097c2bdbea253d6ee4e064f3e65580ef93ac
upstream, and failing to queue the latter results in a null-ptr-deref
reported at the Link below.
In order to avoid conflicts on stable, revert the commit just so that we
can queue its prerequisite patch first and then queue the same after.
Purgatory.ro is a standalone binary that is not linked against the rest of
the kernel. Its image is copied into an array that is linked to the
kernel, and from there kexec relocates it wherever it desires.
Unlike the debug info for vmlinux, which can be used for analyzing crash
such info is useless in purgatory.ro. And discarding them can save about
200K space.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Steve Wahl <steve.wahl@hpe.com> Acked-by: Dave Young <dyoung@redhat.com> Link: https://lore.kernel.org/r/1596433788-3784-1-git-send-email-kernelfans@gmail.com Signed-off-by: Alyssa Ross <hi@alyssa.is> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling dev_set_name() memory is allocated for the name for the
struct device. Once that structure device is registered, or attempted
to be registerd, with the driver core, the driver core will handle
cleaning up that memory when the device is removed from the system.
Unfortunatly for the memstick code, there is an error path that causes
the struct device to never be registered, and so the memory allocated in
dev_set_name will be leaked. Fix that leak by manually freeing it right
before the memory for the device is freed.
Syzbot still reports uninit-value in nilfs_add_checksums_on_logs() for
KMSAN enabled kernels after applying commit 7397031622e0 ("nilfs2:
initialize "struct nilfs_binfo_dat"->bi_pad field").
This is because the unused bytes at the end of each block in segment
summaries are not initialized. So this fixes the issue by padding the
unused bytes with null bytes.
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some USB-SATA adapters have broken behavior when an unsupported VPD page is
probed: Depending on the VPD page number, a 4-byte header with a valid VPD
page number but with a 0 length is returned. Currently, scsi_vpd_inquiry()
only checks that the page number is valid to determine if the page is
valid, which results in receiving only the 4-byte header for the
non-existent page. This error manifests itself very often with page 0xb9
for the Concurrent Positioning Ranges detection done by sd_read_cpr(),
resulting in the following error message:
Building sigaltstack with clang via:
$ ARCH=x86 make LLVM=1 -C tools/testing/selftests/sigaltstack/
produces the following warning:
warning: variable 'sp' is uninitialized when used here [-Wuninitialized]
if (sp < (unsigned long)sstack ||
^~
Clang expects these to be declared at global scope; we've fixed this in
the kernel proper by using the macro `current_stack_pointer`. This is
defined in different headers for different target architectures, so just
create a new header that defines the arch-specific register names for
the stack pointer register, and define it for more targets (at least the
ones that support current_stack_pointer/ARCH_HAS_CURRENT_STACK_POINTER).
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org> Link: https://lore.kernel.org/lkml/CA+G9fYsi3OOu7yCsMutpzKDnBMAzJBCPimBp86LhGBa0eCnEpA@mail.gmail.com/ Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the nid_t field so that its size is correctly reported in the text
format embedded in trace.dat files. As it stands, it is reported as
being of size 4:
field:nid_t nid[3]; offset:24; size:4; signed:0;
Instead of 12:
field:nid_t nid[3]; offset:24; size:12; signed:0;
This also fixes the reported offset of subsequent fields so that they
match with the actual struct layout.
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While using i219-LM card currently it was only possible to achieve
about 60% of maximum speed due to regression introduced in Linux 5.8.
This was caused by TSO not being disabled by default despite commit f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround").
Fix that by disabling TSO during driver probe.
Fixes: f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround") Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230417205345.1030801-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function mlxfw_mfa2_tlv_multi_get() returns NULL if 'tlv' in
question does not pass checks in mlxfw_mfa2_tlv_payload_get(). This
behaviour may lead to NULL pointer dereference in 'multi->total_len'.
Fix this issue by testing mlxfw_mfa2_tlv_multi_get()'s return value
against NULL.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Add error handling of i40e_setup_misc_vector() in i40e_rebuild().
In case interrupt vectors setup fails do not re-open vsi-s and
do not bring up vf-s, we have no interrupts to serve a traffic
anyway.
Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix accessing vsi->active_filters without holding the mac_filter_hash_lock.
Move vsi->active_filters = 0 inside critical section and
move clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state) after the critical
section to ensure the new filters from other threads can be added only after
filters cleaning in the critical section is finished.
Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Here we copy the data from the original buf to the new page. But we
not check that it may be overflow.
As long as the size received(including vnethdr) is greater than 3840
(PAGE_SIZE -VIRTIO_XDP_HEADROOM). Then the memcpy will overflow.
And this is completely possible, as long as the MTU is large, such
as 4096. In our test environment, this will cause crash. Since crash is
caused by the written memory, it is meaningless, so I do not include it.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the TCA_QFQ_LMAX value is not offered through nlattr, lmax is determined by the MTU value of the network device.
The MTU of the loopback device can be set up to 2^31-1.
As a result, it is possible to have an lmax value that exceeds QFQ_MIN_LMAX.
Due to the invalid lmax value, an index is generated that exceeds the QFQ_MAX_INDEX(=24) value, causing out-of-bounds read/write errors.
Code starting with the faulting instruction
===========================================
[ 84.595047] RAX: ffffffffffffffda RBX: 00007ffce388cc70 RCX: 00007fe568032066
[ 84.595281] RDX: 0000000000000040 RSI: 00005605fdad6d10 RDI: 0000000000000003
[ 84.595515] RBP: 00005605fdad6d10 R08: 00007ffce388eeec R09: 0000000000000010
[ 84.595749] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[ 84.595984] R13: 00007ffce388cc30 R14: 00007ffce388b4f0 R15: 0000001d00000001
[ 84.596218] </TASK>
[ 84.596295]
[ 84.596351] Allocated by task 291:
[ 84.596467] kasan_save_stack (mm/kasan/common.c:46)
[ 84.596597] kasan_set_track (mm/kasan/common.c:52)
[ 84.596725] __kasan_kmalloc (mm/kasan/common.c:384)
[ 84.596852] __kmalloc_node (./include/linux/kasan.h:196 mm/slab_common.c:967 mm/slab_common.c:974)
[ 84.596979] qdisc_alloc (./include/linux/slab.h:610 ./include/linux/slab.h:731 net/sched/sch_generic.c:938)
[ 84.597100] qdisc_create (net/sched/sch_api.c:1244)
[ 84.597222] tc_modify_qdisc (net/sched/sch_api.c:1680)
[ 84.597357] rtnetlink_rcv_msg (net/core/rtnetlink.c:6174)
[ 84.597495] netlink_rcv_skb (net/netlink/af_netlink.c:2574)
[ 84.597627] netlink_unicast (net/netlink/af_netlink.c:1340 net/netlink/af_netlink.c:1365)
[ 84.597759] netlink_sendmsg (net/netlink/af_netlink.c:1942)
[ 84.597891] sock_sendmsg (net/socket.c:724 net/socket.c:747)
[ 84.598016] ____sys_sendmsg (net/socket.c:2501)
[ 84.598147] ___sys_sendmsg (net/socket.c:2557)
[ 84.598275] __sys_sendmsg (./include/linux/file.h:31 net/socket.c:2586)
[ 84.598399] do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
[ 84.598520] entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
[ 84.598688]
[ 84.598744] The buggy address belongs to the object at ffff88810f674000
[ 84.598744] which belongs to the cache kmalloc-8k of size 8192
[ 84.599135] The buggy address is located 2664 bytes to the right of
[ 84.599135] allocated 7904-byte region [ffff88810f674000, ffff88810f675ee0)
[ 84.599544]
[ 84.599598] The buggy address belongs to the physical page:
[ 84.599777] page:00000000e638567f refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10f670
[ 84.600074] head:00000000e638567f order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[ 84.600330] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 84.600517] raw: 0200000000010200ffff888100043180dead0000000001220000000000000000
[ 84.600764] raw: 0000000000000000000000008002000200000001ffffffff0000000000000000
[ 84.601009] page dumped because: kasan: bad access detected
[ 84.601187]
[ 84.601241] Memory state around the buggy address:
[ 84.601396] ffff88810f676800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 84.601620] ffff88810f676880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 84.601845] >ffff88810f676900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 84.602069] ^
[ 84.602243] ffff88810f676980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 84.602468] ffff88810f676a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 84.602693] ==================================================================
[ 84.602924] Disabling lock debugging due to kernel taint
Fixes: 3015f3d2a3cd ("pkt_sched: enable QFQ to support TSO/GSO") Reported-by: Gwangun Jung <exsociety@gmail.com> Signed-off-by: Gwangun Jung <exsociety@gmail.com> Acked-by: Jamal Hadi Salim<jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The introduction of the SVE registers to userspace started with a
refactoring of the way we expose any register via the ONE_REG
interface.
Unfortunately, this change doesn't exactly behave as expected
if the number of registers is non-zero and consider everything
to be an error. The visible result is that QEMU barfs very early
when creating vcpus.
Make sure we only exit early in case there is an actual error, rather
than a positive number of registers...
Fixes: be25bbb392fa ("KVM: arm64: Factor out core register ID enumeration") Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Takahiro Itazuri <itazur@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit d26c25a9d19b ("arm64: KVM: Tighten guest core register
access from userspace"), KVM_{GET,SET}_ONE_REG rejects register IDs
that do not correspond to a single underlying architectural register.
KVM_GET_REG_LIST was not changed to match however: instead, it
simply yields a list of 32-bit register IDs that together cover the
whole kvm_regs struct. This means that if userspace tries to use
the resulting list of IDs directly to drive calls to KVM_*_ONE_REG,
some of those calls will now fail.
This was not the intention. Instead, iterating KVM_*_ONE_REG over
the list of IDs returned by KVM_GET_REG_LIST should be guaranteed
to work.
This patch fixes the problem by splitting validate_core_offset()
into a backend core_reg_size_from_offset() which does all of the
work except for checking that the size field in the register ID
matches, and kvm_arm_copy_reg_indices() and num_core_regs() are
converted to use this to enumerate the valid offsets.
kvm_arm_copy_reg_indices() now also sets the register ID size field
appropriately based on the value returned, so the register ID
supplied to userspace is fully qualified for use with the register
access ioctls.
Cc: stable@vger.kernel.org Fixes: d26c25a9d19b ("arm64: KVM: Tighten guest core register access from userspace") Signed-off-by: Dave Martin <Dave.Martin@arm.com> Reviewed-by: Andrew Jones <drjones@redhat.com> Tested-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Takahiro Itazuri <itazur@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding logic to filter out some KVM_REG_ARM_CORE
registers from the KVM_GET_REG_LIST output, this patch factors out
the core register enumeration into a separate function and rebuilds
num_core_regs() on top of it.
This may be a little more expensive (depending on how good a job
the compiler does of specialising the code), but KVM_GET_REG_LIST
is not a hot path.
This will make it easier to consolidate ID filtering code in one
place.
No functional change.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Takahiro Itazuri <itazur@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to honour the max_hw_heartbeat_ms while programming the timeout
value to WOR. Clamp the timeout passed to sbsa_gwdt_set_timeout() to
make sure the programmed value is within the permissible range.
Fixes: abd3ac7902fb ("watchdog: sbsa: Support architecture version 1") Signed-off-by: George Cherian <george.cherian@marvell.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230209021117.1512097-1-george.cherian@marvell.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Tyler Hicks (Microsoft) <code@tyhicks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a successful cpuset_can_attach() call which increments the
attach_in_progress flag, either cpuset_cancel_attach() or cpuset_attach()
will be called later. In cpuset_attach(), tasks in cpuset_attach_wq,
if present, will be woken up at the end. That is not the case in
cpuset_cancel_attach(). So missed wakeup is possible if the attach
operation is somehow cancelled. Fix that by doing the wakeup in
cpuset_cancel_attach() as well.
Fixes: e44193d39e8d ("cpuset: let hotplug propagation work wait for task attaching") Signed-off-by: Waiman Long <longman@redhat.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following process will make ubi attaching failed since commit 1b42b1a36fc946 ("ubi: ensure that VID header offset ... size"):
ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048" # set vid_hdr offset as 2048 (one page)
(dmesg):
ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
UBI error: cannot attach mtd0
UBI error: cannot initialize UBI, error -22
Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.
Fixes: 1b42b1a36fc946 ("ubi: ensure that VID header offset ... size") Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Tested-by: Nicolas Schichan <nschichan@freebox.fr> Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19 Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PE Format Specification (section "The Attribute Certificate Table
(Image Only)") states that `dwLength` is to be rounded up to 8-byte
alignment when used for traversal. Therefore, the field is not required
to be an 8-byte multiple in the first place.
Accordingly, pesign has not performed this alignment since version
0.110. This causes kexec failure on pesign'd binaries with "PEFILE:
Signature wrapper len wrong". Update the comment and relax the check.
Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For quite some time we were chasing a bug which looked like a sudden
permanent failure of networking and mmc on some of our devices.
The bug was very sensitive to any software changes and even more to
any kernel debug options.
Finally we got a setup where the problem was reproducible with
CONFIG_DMA_API_DEBUG=y and it revealed the issue with the rx dma:
Lars was fast to find an explanation: according to the datasheet
bit 2 of the rx buffer descriptor entry has a different meaning in the
extended mode:
Address [2] of beginning of buffer, or
in extended buffer descriptor mode (DMA configuration register [28] = 1),
indicates a valid timestamp in the buffer descriptor entry.
The macb driver didn't mask this bit while getting an address and it
eventually caused a memory corruption and a dma failure.
The problem is resolved by explicitly clearing the problematic bit
if hw timestamping is used.
Fixes: 7b4296148066 ("net: macb: Add support for PTP timestamps in DMA descriptors") Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev> Co-developed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230412232144.770336-1-roman.gushchin@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism") Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.
Fix this by changing direct return to a goto 'out_err'.
Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 71ebd71921e4 ("xen/9pfs: connect to the backend") Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential race condition in hidp_session_thread that may
lead to use-after-free. For instance, the timer is active while
hidp_del_timer is called in hidp_session_thread(). After hidp_session_put,
then 'session' will be freed, causing kernel panic when hidp_idle_timeout
is running.
The solution is to use del_timer_sync instead of del_timer.
Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit d0be8347c623 ("Bluetooth: L2CAP: Fix use-after-free
caused by l2cap_chan_put"), just use l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.
Cc: stable@kernel.org Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIOS botches this one completely - it says the 2nd S/PDIF output is
used, while in fact it's the 1st one. This is tested on DP45SG, but I'm
assuming it's valid for the other boards in the series as well.
Also add some comments regarding the pins.
FWIW, the codec is apparently still sold by Tempo Semiconductor, Inc.,
where one can download the documentation.
Due to two copy/pastos, closing the MIC or EFX capture device would
make a running ADC capture hang due to unsetting its interrupt handler.
In principle, this would have also allowed dereferencing dangling
pointers, but we're actually rather thorough at disabling and flushing
the ints.
While it may sound like one, this actually wasn't a hypothetical bug:
PortAudio will open a capture stream at startup (and close it right
away) even if not asked to. If the first device is busy, it will just
proceed with the next one ... thus killing a concurrent capture.
The si->lock must be held when deleting the si from the available list.
Otherwise, another thread can re-add the si to the available list, which
can lead to memory corruption. The only place we have found where this
happens is in the swapoff path. This case can be described as below:
core 0 core 1
swapoff
del_from_avail_list(si) waiting
try lock si->lock acquire swap_avail_lock
and re-add si into
swap_avail_head
acquire si->lock but missing si already being added again, and continuing
to clear SWP_WRITEOK, etc.
It can be easily found that a massive warning messages can be triggered
inside get_swap_pages() by some special cases, for example, we call
madvise(MADV_PAGEOUT) on blocks of touched memory concurrently, meanwhile,
run much swapon-swapoff operations (e.g. stress-ng-swap).
However, in the worst case, panic can be caused by the above scene. In
swapoff(), the memory used by si could be kept in swap_info[] after
turning off a swap. This means memory corruption will not be caused
immediately until allocated and reset for a new swap in the swapon path.
A panic message caused: (with CONFIG_PLIST_DEBUG enabled)
Now, si->lock locked before calling 'del_from_avail_list()' to make sure
other thread see the si had been deleted and SWP_WRITEOK cleared together,
will not reinsert again.
This problem exists in versions after stable 5.10.y.
Link: https://lkml.kernel.org/r/20230404154716.23058-1-rongwei.wang@linux.alibaba.com Fixes: a2468cc9bfdff ("swap: choose swap device according to numa node") Tested-by: Yongchen Yin <wb-yyc939293@alibaba-inc.com> Signed-off-by: Rongwei Wang <rongwei.wang@linux.alibaba.com> Cc: Bagas Sanjaya <bagasdotme@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Aaron Lu <aaron.lu@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When user reads file 'trace_pipe', kernel keeps printing following logs
that warn at "cpu_buffer->reader_page->read > rb_page_size(reader)" in
rb_get_reader_page(). It just looks like there's an infinite loop in
tracing_read_pipe(). This problem occurs several times on arm64 platform
when testing v5.10 and below.
Then I dump the vmcore and look into the problematic per_cpu ring_buffer,
I found that tail_page/commit_page/reader_page are on the same page while
reader_page->read is obviously abnormal:
tail_page == commit_page == reader_page == {
.write = 0x100d20,
.read = 0x8f9f4805, // Far greater than 0xd20, obviously abnormal!!!
.entries = 0x10004c,
.real_end = 0x0,
.page = {
.time_stamp = 0x857257416af0,
.commit = 0xd20, // This page hasn't been full filled.
// .data[0...0xd20] seems normal.
}
}
The root cause is most likely the race that reader and writer are on the
same page while reader saw an event that not fully committed by writer.
To fix this, add memory barriers to make sure the reader can see the
content of what is committed. Since commit a0fcaaed0c46 ("ring-buffer: Fix
race between reset page and reading page") has added the read barrier in
rb_get_reader_page(), here we just need to add the write barrier.
Link: https://lore.kernel.org/linux-trace-kernel/20230325021247.2923907-1-zhengyejian1@huawei.com Cc: stable@vger.kernel.org Fixes: 77ae365eca89 ("ring-buffer: make lockless") Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the compiler decides not to inline this function then preemption
tracing will always show an IP inside the preemption disabling path and
never the function actually calling preempt_{enable,disable}.
Link: https://lore.kernel.org/linux-trace-kernel/20230327173647.1690849-1-john@metanate.com Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: stable@vger.kernel.org Fixes: f904f58263e1d ("sched/debug: Fix preempt_disable_ip recording for preempt_disable()") Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same task check in perf_event_set_output has some potential issues
for some usages.
For the current perf code, there is a problem if using of
perf_event_open() to have multiple samples getting into the same mmap’d
memory when they are both attached to the same process.
https://lore.kernel.org/all/92645262-D319-4068-9C44-2409EF44888E@gmail.com/
Because the event->ctx is not ready when the perf_event_set_output() is
invoked in the perf_event_open().
Besides the above issue, before the commit bd2756811766 ("perf: Rewrite
core context handling"), perf record can errors out when sampling with
a hardware event and a software event as below.
$ perf record -e cycles,dummy --per-thread ls
failed to mmap with 22 (Invalid argument)
That's because that prior to the commit a hardware event and a software
event are from different task context.
The problem should be a long time issue since commit c3f00c70276d
("perk: Separate find_get_context() from event initialization").
The task struct is stored in the event->hw.target for each per-thread
event. It is a more reliable way to determine whether two events are
attached to the same task.
The event->hw.target was also introduced several years ago by the
commit 50f16a8bf9d7 ("perf: Remove type specific target pointers"). It
can not only be used to fix the issue with the current code, but also
back port to fix the issues with an older kernel.
Note: The event->hw.target was introduced later than commit c3f00c70276d. The patch may cannot be applied between the commit c3f00c70276d and commit 50f16a8bf9d7. Anybody that wants to back-port
this at that period may have to find other solutions.
Fixes: c3f00c70276d ("perf: Separate find_get_context() from event initialization") Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Zhengjun Xing <zhengjun.xing@linux.intel.com> Link: https://lkml.kernel.org/r/20230322202449.512091-1-kan.liang@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The current nilfs2 sysfs support has issues with the timing of creation
and deletion of sysfs entries, potentially leading to null pointer
dereferences, use-after-free, and lockdep warnings.
Some of the sysfs attributes for nilfs2 per-filesystem instance refer to
metadata file "cpfile", "sufile", or "dat", but
nilfs_sysfs_create_device_group that creates those attributes is executed
before the inodes for these metadata files are loaded, and
nilfs_sysfs_delete_device_group which deletes these sysfs entries is
called after releasing their metadata file inodes.
Therefore, access to some of these sysfs attributes may occur outside of
the lifetime of these metadata files, resulting in inode NULL pointer
dereferences or use-after-free.
In addition, the call to nilfs_sysfs_create_device_group() is made during
the locking period of the semaphore "ns_sem" of nilfs object, so the
shrinker call caused by the memory allocation for the sysfs entries, may
derive lock dependencies "ns_sem" -> (shrinker) -> "locks acquired in
nilfs_evict_inode()".
Since nilfs2 may acquire "ns_sem" deep in the call stack holding other
locks via its error handler __nilfs_error(), this causes lockdep to report
circular locking. This is a false positive and no circular locking
actually occurs as no inodes exist yet when
nilfs_sysfs_create_device_group() is called. Fortunately, the lockdep
warnings can be resolved by simply moving the call to
nilfs_sysfs_create_device_group() out of "ns_sem".
This fixes these sysfs issues by revising where the device's sysfs
interface is created/deleted and keeping its lifetime within the lifetime
of the metadata files above.
The finalization of nilfs_segctor_thread() can race with
nilfs_segctor_kill_thread() which terminates that thread, potentially
causing a use-after-free BUG as KASAN detected.
At the end of nilfs_segctor_thread(), it assigns NULL to "sc_task" member
of "struct nilfs_sc_info" to indicate the thread has finished, and then
notifies nilfs_segctor_kill_thread() of this using waitqueue
"sc_wait_task" on the struct nilfs_sc_info.
However, here, immediately after the NULL assignment to "sc_task", it is
possible that nilfs_segctor_kill_thread() will detect it and return to
continue the deallocation, freeing the nilfs_sc_info structure before the
thread does the notification.
This fixes the issue by protecting the NULL assignment to "sc_task" and
its notification, with spinlock "sc_state_lock" of the struct
nilfs_sc_info. Since nilfs_segctor_kill_thread() does a final check to
see if "sc_task" is NULL with "sc_state_lock" locked, this can eliminate
the race.
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports") Cc: stable@vger.kernel.org Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes: 3b8df5fd526e ("iio: Add IIO support for the Measurement Computing CIO-DAC family") Cc: stable@vger.kernel.org Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Silicon Labs IFS-USB-DATACABLE is used in conjunction with for example
the Quint UPSes. It is used to enable Modbus communication with the UPS to
query configuration, power and battery status.
Signed-off-by: Kees Jan Koster <kjkoster@kjkoster.org> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is because icmp6hdr does not in skb linear region under the scenario
of SOCK_RAW socket. Access icmp6_hdr(skb)->icmp6_type directly will
trigger the uninit variable access bug.
Use a local variable icmp6_type to carry the correct value in different
scenarios.
Fixes: 14878f75abd5 ("[IPV6]: Add ICMPMsgStats MIB (RFC 4293) [rev 2]") Reported-by: syzbot+8257f4dcef79de670baf@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=3d605ec1d0a7f2a269a1a6936ac7f2b85975ee9c Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Above issue may happens as follows:
ext4_da_write_begin
ext4_da_write_inline_data_begin
ext4_da_convert_inline_data_to_extent
ext4_clear_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA);
ext4_da_write_end
ext4_run_li_request
ext4_mb_prefetch
ext4_read_block_bitmap_nowait
ext4_validate_block_bitmap
ext4_mark_group_bitmap_corrupted(sb, block_group, EXT4_GROUP_INFO_BBITMAP_CORRUPT)
percpu_counter_sub(&sbi->s_freeclusters_counter,grp->bb_free);
-> sbi->s_freeclusters_counter become zero
ext4_da_write_begin
if (ext4_nonda_switch(inode->i_sb)) -> As freeclusters_counter is zero will return true
*fsdata = (void *)FALL_BACK_TO_NONDELALLOC;
ext4_write_begin
ext4_da_write_end
if (write_mode == FALL_BACK_TO_NONDELALLOC)
ext4_write_end
if (inline_data)
ext4_write_inline_data_end
ext4_write_inline_data
BUG_ON(pos + len > EXT4_I(inode)->i_inline_size);
-> As inode is already convert to extent, so 'pos + len' > inline_size
-> then trigger BUG.
To solve this issue, instead of checking ext4_has_inline_data() which
is only cleared after data has been written back, check the
EXT4_STATE_MAY_INLINE_DATA flag in ext4_write_end().
Fixes: f19d5870cbf7 ("ext4: add normal write support for inline data") Reported-by: syzbot+4faa160fa96bfba639f8@syzkaller.appspotmail.com Reported-by: Jun Nie <jun.nie@linaro.org> Signed-off-by: Ye Bin <yebin10@huawei.com> Link: https://lore.kernel.org/r/20221206144134.1919987-1-yebin@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org
[ta: Fix conflict in if expression and use the local variable inline_data
as it is initialized with ext4_has_inline_data(inode) anyway.] Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is supposed to clear the RH_A_NPS and RH_A_PSM bits, but it's
a no-op because of the & vs | typo. This bug predates git and it was
only discovered using static analysis so it must not affect too many
people in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190817065520.GA29951@mwanda Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing earlyclobber annotation to size, to, and tmp2 operands of the
__clear_user() inline assembly since they are modified or written to before
the last usage of all input operands. This can lead to incorrect register
allocation for the inline assembly.
Fixes: 6c2a9e6df604 ("[S390] Use alternative user-copy operations for new hardware.") Reported-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/all/20230321122514.1743889-3-mark.rutland@arm.com/ Cc: stable@vger.kernel.org Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_gem_prime_mmap() takes a reference on the GEM object, but before that
drm_gem_mmap_obj() already takes a reference, which will be leaked as only
one reference is dropped when the mapping is closed. Drop the extra
reference when dma_buf_mmap() succeeds.
Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been reported that the recent kernel can't probe the PCM devices
on Roland VS-100 properly, and it turned out to be a regression by the
recent addition of the bit shift range check for the format bits.
In the old code, we just did bit-shift and it resulted in zero, which
is then corrected to the standard PCM format, while the new code
explicitly returns an error in such a case.
For addressing the regression, relax the check and fallback to the
standard PCM type (with the info output).
The recent commit f83bb2592482 ("ALSA: hda/conexant: Add quirk for
LENOVO 20149 Notebook model") introduced a quirk for the device with
17aa:3977, but this caused a regression on another model (Lenovo
Ideadpad U31) with the very same PCI SSID. And, through skimming over
the net, it seems that this PCI SSID is used for multiple different
models, so it's no good idea to apply the quirk with the SSID.
Although we may take a different ID check (e.g. the codec SSID instead
of the PCI SSID), unfortunately, the original patch author couldn't
identify the hardware details any longer as the machine was returned,
and we can't develop the further proper fix.
In this patch, instead, we partially revert the change so that the
quirk won't be applied as default for addressing the regression.
Meanwhile, the quirk function itself is kept, and it's now made to be
applicable via the explicit model=lenovo-20149 option.
Since commit d59f6617eef0 ("genirq: Allow fwnode to carry name
information only") an IRQ domain is always given a name during
allocation (e.g. used for the debugfs entry).
Drop the no longer valid name assignment, which would lead to an attempt
to free a string constant when removing the domain on late probe
failures (e.g. probe deferral).
Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only") Cc: stable@vger.kernel.org # 4.13 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> # on SAMA7G5 Link: https://lore.kernel.org/r/20230224130828.27985-1-johan+linaro@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiled with CONFIG_CIFS_DFS_UPCALL disabled, cifs_dfs_d_automount
is NULL. cifs.ko logic for mapping CIFS_FATTR_DFS_REFERRAL attributes to
S_AUTOMOUNT and corresponding dentry flags is retained regardless of
CONFIG_CIFS_DFS_UPCALL, leading to a NULL pointer dereference in
VFS follow_automount() when traversing a DFS referral link:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
<TASK>
__traverse_mounts+0xb5/0x220
? cifs_revalidate_mapping+0x65/0xc0 [cifs]
step_into+0x195/0x610
? lookup_fast+0xe2/0xf0
path_lookupat+0x64/0x140
filename_lookup+0xc2/0x140
? __create_object+0x299/0x380
? kmem_cache_alloc+0x119/0x220
? user_path_at_empty+0x31/0x50
user_path_at_empty+0x31/0x50
__x64_sys_chdir+0x2a/0xd0
? exit_to_user_mode_prepare+0xca/0x100
do_syscall_64+0x42/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
This fix adds an inline cifs_dfs_d_automount() {return -EREMOTE} handler
when CONFIG_CIFS_DFS_UPCALL is disabled. An alternative would be to
avoid flagging S_AUTOMOUNT, etc. without CONFIG_CIFS_DFS_UPCALL. This
approach was chosen as it provides more control over the error path.
Signed-off-by: David Disseldorp <ddiss@suse.de> Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change of -funsigned-char causes additions of negative
numbers to become additions of large positive numbers, leading to wrong
calculations of mouse movement. Change these casts to be explicitly
signed, to take into account negative offsets.
CPU: 1 PID: 5034 Comm: syz-executor350 Not tainted 6.2.0-rc6-syzkaller-80422-geda666ff2276 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
=====================================================
We can follow the call chain and find that 'bcm_tx_setup' function
calls 'memcpy_from_msg' to copy some content to the newly allocated
frame of 'op->frames'. After that the 'len' field of copied structure
being compared with some constant value (64 or 8). However, if
'memcpy_from_msg' returns an error, we will compare some uninitialized
memory. This triggers 'uninit-value' issue.
This patch will add 'memcpy_from_msg' possible errors processing to
avoid uninit-value issue.
When a physical disk is attached directly "without JBOD MAP support" (see
megasas_get_tm_devhandle()) then there is no real error handling in the
driver. Return FAILED instead of SUCCESS.
Fixes: 18365b138508 ("megaraid_sas: Task management support") Signed-off-by: Tomas Henzl <thenzl@redhat.com> Link: https://lore.kernel.org/r/20230324150134.14696-1-thenzl@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
var->pixclock can be assigned to zero by user. Without
proper check, divide by zero would occur when invoking
macro PICOS2KHZ in au1200fb_fb_check_var.
Variable var->pixclock is controlled by user and can be assigned
to zero. Without proper check, divide by zero would occur in
intelfbhw_validate_mode and intelfbhw_mode_to_hw.
variable var->pixclock can be set by user. In case it
equals to zero, divide by zero would occur in nvidiafb_set_par.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to nvidia_check_var and nvidiafb_set_par. We believe it
could also be triggered in driver nvidia from user site.
The getaffinity() system call uses 'cpumask_size()' to decide how big
the CPU mask is - so far so good. It is indeed the allocation size of a
cpumask.
But the code also assumes that the whole allocation is initialized
without actually doing so itself. That's wrong, because we might have
fixed-size allocations (making copying and clearing more efficient), but
not all of it is then necessarily used if 'nr_cpu_ids' is smaller.
Having checked other users of 'cpumask_size()', they all seem to be ok,
either using it purely for the allocation size, or explicitly zeroing
the cpumask before using the size in bytes to copy it.
See for example the ublk_ctrl_get_queue_affinity() function that uses
the proper 'zalloc_cpumask_var()' to make sure that the whole mask is
cleared, whether the storage is on the stack or if it was an external
allocation.
Fix this by just zeroing the allocation before using it. Do the same
for the compat version of sched_getaffinity(), which had the same logic.
Also, for consistency, make sched_getaffinity() use 'cpumask_bits()' to
access the bits. For a cpumask_var_t, it ends up being a pointer to the
same data either way, but it's just a good idea to treat it like you
would a 'cpumask_t'. The compat case already did that.
fb_set_var would by called when user invokes ioctl with cmd
FBIOPUT_VSCREENINFO. User-provided data would finally reach
tgafb_check_var. In case var->pixclock is assigned to zero,
divide by zero would occur when checking whether reciprocal
of var->pixclock is too high.
Similar crashes have happened in other fbdev drivers. There
is no check and modification on var->pixclock along the call
chain to tgafb_check_var. We believe it could also be triggered
in driver tgafb from user site.
sound/pci/hda/patch_ca0132.c:4229:2: note: After for loop, i has value 12
for (i = 0; i < TUNING_CTLS_COUNT; i++)
^
sound/pci/hda/patch_ca0132.c:4234:43: note: Array index out of bounds
dspio_set_param(codec, ca0132_tuning_ctls[i].mid, 0x20,
^
This patch cares non match case.
Therefore, We will get too many warning via cppcheck, like below
sound/pci/asihpi/hpi6205.c:238:27: warning: Possible null pointer dereference: pao [nullPointer]
struct hpi_hw_obj *phw = pao->priv;
^
sound/pci/asihpi/hpi6205.c:433:13: note: Calling function '_HPI_6205', 1st argument 'NULL' value is 0
_HPI_6205(NULL, phm, phr);
^
sound/pci/asihpi/hpi6205.c:401:20: note: Calling function 'control_message', 1st argument 'pao' value is 0
control_message(pao, phm, phr);
^
Set phr->error like many functions doing, and don't call _HPI_6205()
with NULL.
slot_store() uses kstrtouint() to get a slot number, but stores the
result in an "int" variable (by casting a pointer).
This can result in a negative slot number if the unsigned int value is
very large.
A negative number means that the slot is empty, but setting a negative
slot number this way will not remove the device from the array. I don't
think this is a serious problem, but it could cause confusion and it is
best to fix it.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When buffered write fails to copy data into underlying page cache page,
ocfs2_write_end_nolock() just zeroes out and dirties the page. This can
leave dirty page beyond EOF and if page writeback tries to write this page
before write succeeds and expands i_size, page gets into inconsistent
state where page dirty bit is clear but buffer dirty bits stay set
resulting in page data never getting written and so data copied to the
page is lost. Fix the problem by invalidating page beyond EOF after
failed write.
Link: https://lkml.kernel.org/r/20230302153843.18499-1-jack@suse.cz Fixes: 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ replace block_invalidate_folio to block_invalidatepage ] Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 829c1651e9c4 ("sched/fair: sanitize vruntime of entity being placed")
fixes an overflowing bug, but ignore a case that se->exec_start is reset
after a migration.
For fixing this case, we delay the reset of se->exec_start after
placing the entity which se->exec_start to detect long sleeping task.
In order to take into account a possible divergence between the clock_task
of 2 rqs, we increase the threshold to around 104 days.
Fixes: 829c1651e9c4 ("sched/fair: sanitize vruntime of entity being placed") Originally-by: Zhang Qiao <zhangqiao22@huawei.com> Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Zhang Qiao <zhangqiao22@huawei.com> Link: https://lore.kernel.org/r/20230317160810.107988-1-vincent.guittot@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a scheduling entity is placed onto cfs_rq, its vruntime is pulled
to the base level (around cfs_rq->min_vruntime), so that the entity
doesn't gain extra boost when placed backwards.
However, if the entity being placed wasn't executed for a long time, its
vruntime may get too far behind (e.g. while cfs_rq was executing a
low-weight hog), which can inverse the vruntime comparison due to s64
overflow. This results in the entity being placed with its original
vruntime way forwards, so that it will effectively never get to the cpu.
To prevent that, ignore the vruntime of the entity being placed if it
didn't execute for much longer than the characteristic sheduler time
scale.
The data->block[0] variable comes from user and is a number between
0-255. Without proper check, the variable may be very large to cause
an out-of-bounds when performing memcpy in slimpro_i2c_blkwr.
The ioctl helper function nilfs_ioctl_wrap_copy(), which exchanges a
metadata array to/from user space, may copy uninitialized buffer regions
to user space memory for read-only ioctl commands NILFS_IOCTL_GET_SUINFO
and NILFS_IOCTL_GET_CPINFO.
This can occur when the element size of the user space metadata given by
the v_size member of the argument nilfs_argv structure is larger than the
size of the metadata element (nilfs_suinfo structure or nilfs_cpinfo
structure) on the file system side.
KMSAN-enabled kernels detect this issue as follows:
The user may call role_store() when driver is handling
ci_handle_id_switch() which is triggerred by otg event or power lost
event. Unfortunately, the controller may go into chaos in this case.
Fix this by protecting it with mutex lock.
projects / linux-stable / log