Starting with gcc-8.1, we get a warning about all system call definitions,
which use an alias between functions with incompatible prototypes, e.g.:
In file included from ../mm/process_vm_access.c:19:
../include/linux/syscalls.h:211:18: warning: 'sys_process_vm_readv' alias between functions of incompatible types 'long int(pid_t, const struct iovec *, long unsigned int, const struct iovec *, long unsigned int, long unsigned int)' {aka 'long int(int, const struct iovec *, long unsigned int, const struct iovec *, long unsigned int, long unsigned int)'} and 'long int(long int, long int, long int, long int, long int, long int)' [-Wattribute-alias]
asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
^~~
../include/linux/syscalls.h:207:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
^~~~~~~~~~~~~~~~~
../include/linux/syscalls.h:201:36: note: in expansion of macro 'SYSCALL_DEFINEx'
#define SYSCALL_DEFINE6(name, ...) SYSCALL_DEFINEx(6, _##name, __VA_ARGS__)
^~~~~~~~~~~~~~~
../mm/process_vm_access.c:300:1: note: in expansion of macro 'SYSCALL_DEFINE6'
SYSCALL_DEFINE6(process_vm_readv, pid_t, pid, const struct iovec __user *, lvec,
^~~~~~~~~~~~~~~
../include/linux/syscalls.h:215:18: note: aliased declaration here
asmlinkage long SyS##name(__MAP(x,__SC_LONG,__VA_ARGS__)) \
^~~
../include/linux/syscalls.h:207:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
^~~~~~~~~~~~~~~~~
../include/linux/syscalls.h:201:36: note: in expansion of macro 'SYSCALL_DEFINEx'
#define SYSCALL_DEFINE6(name, ...) SYSCALL_DEFINEx(6, _##name, __VA_ARGS__)
^~~~~~~~~~~~~~~
../mm/process_vm_access.c:300:1: note: in expansion of macro 'SYSCALL_DEFINE6'
SYSCALL_DEFINE6(process_vm_readv, pid_t, pid, const struct iovec __user *, lvec,
This is really noisy and does not indicate a real problem. In the latest
mainline kernel, this was addressed by commit bee20031772a ("disable
-Wattribute-alias warning for SYSCALL_DEFINEx()"), which seems too invasive
to backport.
This takes a much simpler approach and just disables the warning across the
kernel.
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.
This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.
This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).
Fix that by enabling the RXOFLW interrupt.
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.
Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().
Fixes: b1201e44f50b ("can: xilinx CAN controller support") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.
Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.
There are several issues with the suspend/resume handling code of the
driver:
- The device is attached and detached in the runtime_suspend() and
runtime_resume() callbacks if the interface is running. However,
during xcan_chip_start() the interface is considered running,
causing the resume handler to incorrectly call netif_start_queue()
at the beginning of xcan_chip_start(), and on xcan_chip_start() error
return the suspend handler detaches the device leaving the user
unable to bring-up the device anymore.
- The device is not brought properly up on system resume. A reset is
done and the code tries to determine the bus state after that.
However, after reset the device is always in Configuration mode
(down), so the state checking code does not make sense and
communication will also not work.
- The suspend callback tries to set the device to sleep mode (low-power
mode which monitors the bus and brings the device back to normal mode
on activity), but then immediately disables the clocks (possibly
before the device reaches the sleep mode), which does not make sense
to me. If a clean shutdown is wanted before disabling clocks, we can
just bring it down completely instead of only sleep mode.
Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.
The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.
xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.
Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.
Tested on Zynq-7000 integrated CAN.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Commit 52cdbdd49853 (driver core: correct device's shutdown order)
introduced a regression by breaking device shutdown on some systems.
Namely, the devices_kset_move_last() call in really_probe() added by
that commit is a mistake as it may cause parents to follow children
in the devices_kset list which then causes shutdown to fail. For
example, if a device has children before really_probe() is called
for it (which is not uncommon), that call will cause it to be
reordered after the children in the devices_kset list and the
ordering of that list will not reflect the correct device shutdown
order any more.
Also it causes the devices_kset list to be constantly reordered
until all drivers have been probed which is totally pointless
overhead in the majority of cases and it only covered an issue
with system shutdown, while system-wide suspend/resume potentially
had the same issue on the affected platforms (which was not covered).
Moreover, the shutdown issue originally addressed by the change in
really_probe() made by commit 52cdbdd49853 is not present in 4.18-rc
any more, since dra7 started to use the sdhci-omap driver which
doesn't disable any regulators during shutdown, so the really_probe()
part of commit 52cdbdd49853 can be safely reverted. [The original
issue was related to the omap_hsmmc driver used by dra7 previously.]
For the above reasons, revert the really_probe() modifications made
by commit 52cdbdd49853.
The other code changes made by commit 52cdbdd49853 are useful and
they need not be reverted.
Fixes: 52cdbdd49853 (driver core: correct device's shutdown order) Link: https://lore.kernel.org/lkml/CAFgQCTt7VfqM=UyCnvNFxrSw8Z6cUtAi3HUwR4_xPAc03SgHjQ@mail.gmail.com/ Reported-by: Pingfan Liu <kernelfans@gmail.com> Tested-by: Pingfan Liu <kernelfans@gmail.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4e4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
The commit 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in a more supported way") Cc: <stable@vger.kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens") Cc: <stable@vger.kernel.org> Tested-by: Alessandro Antenucci <antenucci@korg.it> Signed-off-by: Bin Liu <b-liu@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If softsynthx_read() is called with `count < 3`, `count - 3` wraps, causing
the loop to copy as much data as available to the provided buffer. If
softsynthx_read() is invoked through sys_splice(), this causes an
unbounded kernel write; but even when userspace just reads from it
normally, a small size could cause userspace crashes.
In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.
I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.
Fixes: 9f5afeae5152 ("tcp: use an RB tree for ooo receive queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.
1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.
We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.
In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :
if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
tcp_clamp_window(sk);
tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])
Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.
Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.
Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.
Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.
Strategy taken in this patch is to purge ~12.5 % of the queue capacity.
Fixes: 36a6503fedda ("tcp: refine tcp_prune_ofo_queue() to not drop all packets") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, when a data segment was sent an ACK was piggybacked
on the data segment without generating a CA_EVENT_NON_DELAYED_ACK
event to notify congestion control modules. So the DCTCP
ca->delayed_ack_reserved flag could incorrectly stay set when
in fact there were no delayed ACKs being reserved. This could result
in sending a special ECN notification ACK that carries an older
ACK sequence, when in fact there was no need for such an ACK.
DCTCP keeps track of the delayed ACK status with its own separate
state ca->delayed_ack_reserved. Previously it may accidentally cancel
the delayed ACK without updating this field upon sending a special
ACK that carries a older ACK sequence. This inconsistency would
lead to DCTCP receiver never acknowledging the latest data until the
sender times out and retry in some cases.
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Reported-by: Larry Brakmo <brakmo@fb.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c79 ("vxlan: add implicit fdb entry for default destination") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new option do_notify to vxlan_fdb_destroy to make
sending netlink notify optional. Used by a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current sg coalescing logic in sk_alloc_sg() (latter is used by tls and
sockmap) is not quite correct in that we do fetch the previous sg entry,
however the subsequent check whether the refilled page frag from the
socket is still the same as from the last entry with prior offset and
length matching the start of the current buffer is comparing always the
first sg list entry instead of the prior one.
Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable interrupt") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hangbin Liu [Fri, 20 Jul 2018 06:04:27 +0000 (14:04 +0800)]
multicast: do not restore deleted record source filter mode to new one
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
Fixes: 24803f38a5c0b (igmp: do not remove igmp souce list info when set link down) Fixes: 1666d49e1d416 (mld: do not remove mld souce list info when set link down) Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff74384600a ("net: vrf: Handle ipv6 multicast and link-local addresses") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When driver converts HW timestamp to wall clock time it subtracts
the last saved cycle counter from the HW timestamp and converts the
difference to nanoseconds.
The conversion is done by multiplying the cycles difference with the
clock multiplier value as a first step and therefore the cycles
difference should be small enough so that the multiplication product
doesn't exceed 64bit.
The overflow handling routine is in charge of updating the last saved
cycle counter in driver and it is called periodically using kernel
delayed workqueue.
The delay period for this work is calculated using the max HW cycle
counter value (a 41 bit mask) as a base which doesn't take the 64bit
limit into account so the delay period may be incorrect and too
long to prevent a large difference between the HW counter and the last
saved counter in SW.
This change adjusts the work period for the HW clock overflow work by
taking the minimum between the previous value and the quotient of max
u64 value and the clock multiplier value.
Fixes: ddff00d42043 ("net: Move skb_has_shared_frag check out of GRE code and into segmentation") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.
However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.
Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
Fixes: b73c3d0e4f0e ("net: Save TX flow hash in sock and set in skbuf on xmit") Fixes: 67800f9b1f4e ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda0744, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu> Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A CRTC being enabled doesn't mean it's on! It doesn't even necessarily
mean it's being used. This fixes runtime PM leaks on the P50 I've got
next to me.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A VM which has:
- a DMA capable device passed through to it (eg. network card);
- running a malicious kernel that ignores H_PUT_TCE failure;
- capability of using IOMMU pages bigger that physical pages
can create an IOMMU mapping that exposes (for example) 16MB of
the host physical memory to the device when only 64K was allocated to the VM.
The remaining 16MB - 64K will be some other content of host memory, possibly
including pages of the VM, but also pages of host kernel memory, host
programs or other VMs.
The attacking VM does not control the location of the page it can map,
and is only allowed to map as many pages as it has pages of RAM.
We already have a check in drivers/vfio/vfio_iommu_spapr_tce.c that
an IOMMU page is contained in the physical page so the PCI hardware won't
get access to unassigned host memory; however this check is missing in
the KVM fastpath (H_PUT_TCE accelerated code). We were lucky so far and
did not hit this yet as the very first time when the mapping happens
we do not have tbl::it_userspace allocated yet and fall back to
the userspace which in turn calls VFIO IOMMU driver, this fails and
the guest does not retry,
This stores the smallest preregistered page size in the preregistered
region descriptor and changes the mm_iommu_xxx API to check this against
the IOMMU page size.
This calculates maximum page size as a minimum of the natural region
alignment and compound page size. For the page shift this uses the shift
returned by find_linux_pte() which indicates how the page is mapped to
the current userspace - if the page is huge and this is not a zero, then
it is a leaf pte and the page is mapped within the range.
The MIPS implementation of pci_resource_to_user() introduced in v3.12 by
commit 4c2924b725fb ("MIPS: PCI: Use pci_resource_to_user to map pci
memory space properly") incorrectly sets *end to the address of the
byte after the resource, rather than the last byte of the resource.
This results in userland seeing resources as a byte larger than they
actually are, for example a 32 byte BAR will be reported by a tool such
as lspci as being 33 bytes in size:
Region 2: I/O ports at 1000 [disabled] [size=33]
Correct this by subtracting one from the calculated end address,
reporting the correct address to userland.
Signed-off-by: Paul Burton <paul.burton@mips.com> Reported-by: Rui Wang <rui.wang@windriver.com> Fixes: 4c2924b725fb ("MIPS: PCI: Use pci_resource_to_user to map pci memory space properly") Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org # v3.12+
Patchwork: https://patchwork.linux-mips.org/patch/19829/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philip reports:
seems adding "cifs: Fix slab-out-of-bounds in send_set_info() on SMB2
ACE setting" (commit 748144f) [1] created a regression within linux
v4.14 kernel series. Writing to a mounted cifs either freezes on writing
or crashes the PC. A more detailed explanation you may find in our
forums [2]. Reverting the patch, seems to "fix" it. Thoughts?
[2] https://forum.manjaro.org/t/53250
Reported-by: Philip Müller <philm@manjaro.org> Cc: Jianhong Yin <jiyin@redhat.com> Cc: Stefano Brivio <sbrivio@redhat.com> Cc: Aurelien Aptel <aaptel@suse.com> Cc: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror
SPRN_USPRG3 are used as userspace VDSO write and read registers
respectively.
SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not
restored. As a result, any read from SPRN_USPRG3 returns zero on an
exit from stop4 (Power9 only) and above.
Thus in this situation, on POWER9, any call from sched_getcpu() always
returns zero, as on powerpc, we call __kernel_getcpu() which relies
upon SPRN_USPRG3 to report the CPU and NUMA node information.
Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state
with the sprg_vdso value that is cached in PACA.
Fixes: e1c1cfed5432 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Florian Weimer <fweimer@redhat.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.
If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.
Ugly scapy test script running on veth0:
def loop():
pkt=sniff(iface="veth0", filter="icmp6", count=1)
pkt = pkt[0]
b = bytearray(pkt[Raw].load)
b[1] += 1
b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
pkt[Raw].load = bytes(b)
pkt[IPv6].plen += 8
# fixup checksum after modifying the payload
pkt[IPv6].payload.cksum -= 0x3b44
if pkt[IPv6].payload.cksum < 0:
pkt[IPv6].payload.cksum += 0xffff
sendp(pkt, iface="veth0")
This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.
Fixes: adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a51803 ("netvsc: optimize receive completions") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244c0 ("ptp: Allow reassigning calibration pin function") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.
Fixes: cd2fbe1b6b51 ("net: Use VRF device index for lookups on RX") Reported-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b7008620b84 ("net: Don't copy pfmemalloc flag in
__copy_skb_header()") introduced a different handling for the
pfmemalloc flag in copy and clone paths.
In __skb_clone(), now, the flag is set only if it was set in the
original skb, but not cleared if it wasn't. This is wrong and
might lead to socket buffers being flagged with pfmemalloc even
if the skb data wasn't allocated from pfmemalloc reserves. Copy
the flag instead of ORing it.
Reported-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 8b7008620b84 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit b19372273164 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit a9e419dc7be6 ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.
Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.
Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath Fixes: d7226c7a4dd1 ("net: diag: Fix refcnt leak in error path destroying socket") Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rhashtable_init() currently does not take into account the user-passed
min_size parameter unless param->nelem_hint is set as well. As such,
the default size (number of buckets) will always be HASH_DEFAULT_SIZE
even if the smallest allowed size is larger than that. Remediate this
by unconditionally calling into rounded_hashtable_size() and handling
things accordingly.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.
>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.
Fixes: 79ff2fc31e0f ("ila: Cache a route to translated address") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.
This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Tested-by: Pete Heist <pete@heistp.net> Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100ffffea001da3be08ffffea001da25a08ffff88084000d0c0
[ 201.039582] raw: 000000000000000000000000000d000d00000001ffffffff0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.
When cpu_stop_queue_two_works() begins to wake the stopper threads, it does
so without preemption disabled, which leads to the following race
condition:
The source CPU calls cpu_stop_queue_two_works(), with cpu1 as the source
CPU, and cpu2 as the destination CPU. When adding the stopper threads to
the wake queue used in this function, the source CPU stopper thread is
added first, and the destination CPU stopper thread is added last.
When wake_up_q() is invoked to wake the stopper threads, the threads are
woken up in the order that they are queued in, so the source CPU's stopper
thread is woken up first, and it preempts the thread running on the source
CPU.
The stopper thread will then execute on the source CPU, disable preemption,
and begin executing multi_cpu_stop(), and wait for an ack from the
destination CPU's stopper thread, with preemption still disabled. Since the
worker thread that woke up the stopper thread on the source CPU is affine
to the source CPU, and preemption is disabled on the source CPU, that
thread will never run to dequeue the destination CPU's stopper thread from
the wake queue, and thus, the destination CPU's stopper thread will never
run, causing the source CPU's stopper thread to wait forever, and stall.
Disable preemption when waking the stopper threads in
cpu_stop_queue_two_works().
The size is always equal to 1 page so let's use this. Later on this will
be used for other checks which use page shifts to check the granularity
of access.
This should cause no behavioral change.
Cc: stable@vger.kernel.org # v4.12+ Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing info.index before indirectly using it to index
vdev->region
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744da (intel_pstate: skip the driver if ACPI has power mgmt option) Reported-by: Andreas Herrmann <aherrmann@suse.com> Reviewed-by: Andreas Herrmann <aherrmann@suse.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Andreas Herrmann <aherrmann@suse.com> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__split_huge_pmd_locked() must check if the cleared huge pmd was dirty,
and propagate that to PageDirty: otherwise, data may be lost when a huge
tmpfs page is modified then split then reclaimed.
How has this taken so long to be noticed? Because there was no problem
when the huge page is written by a write system call (shmem_write_end()
calls set_page_dirty()), nor when the page is allocated for a write fault
(fault_dirty_shared_page() calls set_page_dirty()); but when allocated for
a read fault (which MAP_POPULATE simulates), no set_page_dirty().
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1807111741430.1106@eggly.anvils Fixes: d21b9e57c74c ("thp: handle file pages in split_huge_pmd()") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Ashwin Chaugule <ashwinch@google.com> Reviewed-by: Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that a kernel crash happened in mem_cgroup_iter(), which
can be triggered if the legacy cgroup-v1 non-hierarchical mode is used.
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f
......
Call trace:
mem_cgroup_iter+0x2e0/0x6d4
shrink_zone+0x8c/0x324
balance_pgdat+0x450/0x640
kswapd+0x130/0x4b8
kthread+0xe8/0xfc
ret_from_fork+0x10/0x20
mem_cgroup_iter():
......
if (css_tryget(css)) <-- crash here
break;
......
The crashing reason is that mem_cgroup_iter() uses the memcg object whose
pointer is stored in iter->position, which has been freed before and
filled with POISON_FREE(0x6b).
And the root cause of the use-after-free issue is that
invalidate_reclaim_iterators() fails to reset the value of iter->position
to NULL when the css of the memcg is released in non- hierarchical mode.
Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com Fixes: 6df38689e0e9 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim") Signed-off-by: Jing Xia <jing.xia.mail@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <chunyan.zhang@unisoc.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mprotect(EXEC) was failing for stack mappings as default vm flags was
missing MAYEXEC.
This was triggered by glibc test suite nptl/tst-execstack testcase
What is surprising is that despite running LTP for years on, we didn't
catch this issue as it lacks a directed test case.
gcc dejagnu tests with nested functions also requiring exec stack work
fine though because they rely on the GNU_STACK segment spit out by
compiler and handled in kernel elf loader.
This glibc case is different as the stack is non exec to begin with and
a dlopen of shared lib with GNU_STACK segment triggers the exec stack
proceedings using a mprotect(PROT_EXEC) which was broken.
We used to have pre-set CONFIG_INITRAMFS_SOURCE with local path
to intramfs in ARC defconfigs. This was quite convenient for
in-house development but not that convenient for newcomers
who obviusly don't have folders like "arc_initramfs" next to
the Linux source tree. Which leads to quite surprising failure
of defconfig building:
------------------------------->8-----------------------------
../scripts/gen_initramfs_list.sh: Cannot open '../../arc_initramfs_hs/'
../usr/Makefile:57: recipe for target 'usr/initramfs_data.cpio.gz' failed
make[2]: *** [usr/initramfs_data.cpio.gz] Error 1
------------------------------->8-----------------------------
So now when more and more people start to deal with our defconfigs
let's make their life easier with removal of CONFIG_INITRAMFS_SOURCE.
swap was broken on ARC due to silly copy-paste issue.
We encode offset from swapcache page in __swp_entry() as (off << 13) but
were not decoding back in __swp_offset() as (off >> 13) - it was still
(off << 13).
This manifsted as strace segfaulting on HSDK because gcc was targetting
the accumulator registers as GPRs, which kernek was not saving/restoring
by default.
The SNDRV_RAWMIDI_IOCTL_PARAMS ioctl may resize the buffers and the
current code is racy. For example, the sequencer client may write to
buffer while it being resized.
As a simple workaround, let's switch to the resized buffer inside the
stream runtime lock.
In parse_options(), if match_strdup() failed, parse_options() leaves
opts->iocharset in unexpected state (i.e. still pointing the freed
string). And this can be the cause of double free.
To fix, this initialize opts->iocharset always when freeing.
commit b3b7c4795c ("x86/MCE: Serialize sysfs changes") introduced a min
interval limitation when setting the check interval for polled MCEs.
However, the logic is that 0 disables polling for corrected MCEs, see
Documentation/x86/x86_64/machinecheck. The limitation prevents disabling.
Remove this limitation and allow the value 0 to disable polling again.
Markus reported that BTS is sporadically missing the tail of the trace
in the perf_event data buffer: [decode error (1): instruction overflow]
shown in GDB; and bisected it to the conversion of debug_store to PTI.
A little "optimization" crept into alloc_bts_buffer(), which mistakenly
placed bts_interrupt_threshold away from the 24-byte record boundary.
Intel SDM Vol 3B 17.4.9 says "This address must point to an offset from
the BTS buffer base that is a multiple of the BTS record size."
Revert "max" from a byte count to a record count, to calculate the
bts_interrupt_threshold correctly: which turns out to fix problem seen.
Fixes: c1961a4631da ("x86/events/intel/ds: Map debug buffers in cpu_entry_area") Reported-and-tested-by: Markus T Metzger <markus.t.metzger@intel.com> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@intel.com> Cc: Andi Kleen <andi.kleen@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org # v4.14+ Link: https://lkml.kernel.org/r/alpine.LSU.2.11.1807141248290.1614@eggly.anvils Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: dd84441a7971 ("x86/speculation: Use IBRS if available before calling into firmware") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709133534.5963-1-ville.syrjala@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reports crashes in kvm_irqfd_assign(), caused by use-after-free
when kvm_irqfd_assign() and kvm_irqfd_deassign() run in parallel
for one specific eventfd. When the assign path hasn't finished but irqfd
has been added to kvm->irqfds.items list, another thead may deassign the
eventfd and free struct kvm_kernel_irqfd(). The assign path then uses
the struct kvm_kernel_irqfd that has been freed by deassign path. To avoid
such issue, keep irqfd under kvm->irq_srcu protection after the irqfd
has been added to kvm->irqfds.items list, and call synchronize_srcu()
in irq_shutdown() to make sure that irqfd has been fully initialized in
the assign path.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Tianyu Lan <tianyu.lan@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the description of sd_zbc_check_zone_size() to correctly explain that
the returned value is a number of device blocks, not bytes. Additionally,
the 32 bits "ret" variable used in this function may truncate the 64 bits
zone_blocks variable value upon return. To fix this, change "ret" type to
s64.
Fixes: ccce20fc79 ("sd_zbc: Avoid that resetting a zone fails sporadically") Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: stable@kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
e7fd37ba1217 ("cgroup: avoid copying strings longer than the buffers")
converted possibly unsafe strncpy() usages in cgroup to strscpy().
However, although the callsites are completely fine with truncated
copied, because strscpy() is marked __must_check, it led to the
following warnings.
kernel/cgroup/cgroup.c: In function ‘cgroup_file_name’:
kernel/cgroup/cgroup.c:1400:10: warning: ignoring return value of ‘strscpy’, declared with attribute warn_unused_result [-Wunused-result]
strscpy(buf, cft->name, CGROUP_FILE_NAME_MAX);
^
To avoid the warnings, 50034ed49645 ("cgroup: use strlcpy() instead of
strscpy() to avoid spurious warning") switched them to strlcpy().
strlcpy() is worse than strlcpy() because it unconditionally runs
strlen() on the source string, and the only reason we switched to
strlcpy() here was because it was lacking __must_check, which doesn't
reflect any material differences between the two function. It's just
that someone added __must_check to strscpy() and not to strlcpy().
These basic string copy operations are used in variety of ways, and
one of not-so-uncommon use cases is safely handling truncated copies,
where the caller naturally doesn't care about the return value. The
__must_check doesn't match the actual use cases and forces users to
opt for inferior variants which lack __must_check by happenstance or
spread ugly (void) casts.
Remove __must_check from strscpy() and restore strscpy() usages in
cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Chris Metcalf <cmetcalf@ezchip.com>
[backport only the string.h portion to remove build warnings starting to show up - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all our infrastructure is in place, let's expose the
availability of ARCH_WORKAROUND_2 to guests. We take this opportunity
to tidy up a couple of SMCCC constants.
Acked-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to forward the guest's ARCH_WORKAROUND_2 calls to EL3,
add a small(-ish) sequence to handle it at EL2. Special care must
be taken to track the state of the guest itself by updating the
workaround flags. We also rely on patching to enable calls into
the firmware.
Note that since we need to execute branches, this always executes
after the Spectre-v2 mitigation has been applied.
Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to offer ARCH_WORKAROUND_2 support to guests, we need
a bit of infrastructure.
Let's add a flag indicating whether or not the guest uses
SSBD mitigation. Depending on the state of this flag, allow
KVM to disable ARCH_WORKAROUND_2 before entering the guest,
and enable it when exiting it.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we're going to require to access per-cpu variables at EL2,
let's craft the minimum set of accessors required to implement
reading a per-cpu variable, relying on tpidr_el2 to contain the
per-cpu offset.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log