NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0cf4 ("mac80211: add ieee80211_tx_status_noskb") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes stale beacon-int values that would keep a netdev
from going up.
To reproduce:
Create two VAP on one radio.
vap1 has beacon-int 100, start it.
vap2 has beacon-int 240, start it (and it will fail
because beacon-int mismatch).
reconfigure vap2 to have beacon-int 100 and start it.
It will fail because the stale beacon-int 240 will be used
in the ifup path and hostapd never gets a chance to set the
new beacon interval.
Cc: stable@vger.kernel.org Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise if network manager starts configuring Wi-Fi interface
immidiatelly after getting notification of its creation, we will get
NULL pointer dereference:
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
[1]: https://github.com/pmem/ndctl/issues/76
Fixes: cfe30b872058 ("libnvdimm, pmem: adjust for section collisions with...") Cc: <stable@vger.kernel.org> Reported-by: Patrick Geary <patrickg@supermicro.com> Tested-by: Patrick Geary <patrickg@supermicro.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: Macpaul Lin <macpaul@gmail.com> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since Commit 761ed4a94582 ('tty: serial_core: convert uart_close to use
tty_port_close') and Commit 4dda864d7307 ('tty: serial_core: Fix serial
console crash on port shutdown), a serial port which is used as
console can be stuck when logging out if there is a remained process.
After logged out, agetty will try to grab the serial port but it will
be failed because the previous process did not release the port
correctly. To fix this, TTY_IO_ERROR bit should not be enabled of
tty_port_close if the port is console port.
Reproduce step:
- Run background processes from serial console
$ while true; do sleep 10; done &
- Log out
$ logout
-> Stuck
- Read journal log by journalctl | tail
Jan 28 16:07:01 ubuntu systemd[1]: Stopped Serial Getty on ttyAMA0.
Jan 28 16:07:01 ubuntu systemd[1]: Started Serial Getty on ttyAMA0.
Jan 28 16:07:02 ubuntu agetty[1643]: /dev/ttyAMA0: not a tty
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close") Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Rob Herring <robh@kernel.org> Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by: Chanho Park <parkch98@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling") Signed-off-by: Peter Shih <pihsun@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmbus_process_offer() mustn't call channel->sc_creation_callback()
directly for sub-channels, because sc_creation_callback() ->
vmbus_open() may never get the host's response to the
OPEN_CHANNEL message (the host may rescind a channel at any time,
e.g. in the case of hot removing a NIC), and vmbus_onoffer_rescind()
may not wake up the vmbus_open() as it's blocked due to a non-zero
vmbus_connection.offer_in_progress, and finally we have a deadlock.
The above is also true for primary channels, if the related device
drivers use sync probing mode by default.
And, usually the handling of primary channels and sub-channels can
depend on each other, so we should offload them to different
workqueues to avoid possible deadlock, e.g. in sync-probing mode,
NIC1's netvsc_subchan_work() can race with NIC2's netvsc_probe() ->
rtnl_lock(), and causes deadlock: the former gets the rtnl_lock
and waits for all the sub-channels to appear, but the latter
can't get the rtnl_lock and this blocks the handling of sub-channels.
The patch can fix the multiple-NIC deadlock described above for
v3.x kernels (e.g. RHEL 7.x) which don't support async-probing
of devices, and v4.4, v4.9, v4.14 and v4.18 which support async-probing
but don't enable async-probing for Hyper-V drivers (yet).
The patch can also fix the hang issue in sub-channel's handling described
above for all versions of kernels, including v4.19 and v4.20-rc4.
So actually the patch should be applied to all the existing kernels,
not only the kernels that have 8195b1396ec8.
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug") Cc: stable@vger.kernel.org Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8b7a13c3f404 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
Fixes: 8b7a13c3f404 ("staging: r8712u: Fix possible buffer overrun") Signed-off-by: Young Xiao <YangX92@hotmail.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[for older kernels only, atomisp has been removed from upstream]
gcc-8 rightfully warns that this instance of strncpy is just copying
from the source, to the same source, for a few bytes. Meaning this call
does nothing. As the author of the code obviously meant it to do
something, but this code must be working properly, just replace the call
to the kernel internal strscpy() which gcc doesn't know about, so the
warning goes away.
As this driver was deleted from newer kernel versions, none of this
really matters but now at least we do not have to worry about a build
warning in the stable trees.
[for older kernels only, lustre has been removed from upstream]
When someone writes:
strncpy(dest, source, sizeof(source));
they really are just doing the same thing as:
strcpy(dest, source);
but somehow they feel better because they are now using the "safe"
version of the string functions. Cargo-cult programming at its
finest...
gcc-8 rightfully warns you about doing foolish things like this. Now
that the stable kernels are all starting to be built using gcc-8, let's
get rid of this warning so that we do not have to gaze at this horror.
To dropt the warning, just convert the code to using strcpy() so that if
someone really wants to audit this code and find all of the obvious
problems, it will be easier to do so.
This patch adds f2fs_is_valid_blkaddr() in below functions to do sanity
check with block address to avoid pentential panic:
- f2fs_grab_read_bio()
- __written_first_block()
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Cc: <stable@vger.kernel.org> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm compiler internally interprets an inline assembly label
as an unsigned long value, not a pointer. As a result, under
CONFIG_FORTIFY_SOURCE, the address of a label has a size of 4 bytes,
which was tripping the runtime checks. Instead, we can just cast the label
(as done with the size calculations earlier).
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes: 975faaeb9985 ("dma: cppi41: start tear down only if channel is busy") Cc: stable@vger.kernel.org # v3.15+ Signed-off-by: Bin Liu <b-liu@ti.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
call_encode can be invoked more than once per RPC call. Ensure that
each call to gss_wrap_req_priv does not overwrite pointers to
previously allocated memory.
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Cc: stable@vger.kernel.org Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432
This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.
Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.
Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Colin Ian King <colin.king@canonical.com> Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-3-pasic@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().
This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-2-pasic@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've got a regression report for some Thinkpad models (at least
T570s) which shows the too low speaker output volume. The bisection
leaded to the commit 61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad
Dock device for ALC298 platform"), and it's basically adding the two
pin configurations for the dock, and looks harmless.
The real culprit seems, though, that the DAC assignment for the
speaker pin is implicitly assumed on these devices, i.e. pin NID 0x14
to be coupled with DAC NID 0x03. When more pins are configured by the
commit above, the auto-parser changes the DAC assignment, and this
resulted in the regression.
As a workaround, just provide the fixed pin / DAC mapping table for
this Thinkpad fixup function. It's no generic solution, but the
problem itself is pretty much device-specific, so must be good
enough.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1554304 Fixes: 61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform") Cc: <stable@vger.kernel.org> Reported-and-tested-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As addressed in alsa-lib (commit b420056604f0), we need to fix the
case where the evaluation of PCM interval "(x x+1]" leading to
-EINVAL. After applying rules, such an interval may be translated as
"(x x+1)".
Fixes: ff2d6acdf6f1 ("ALSA: pcm: Fix snd_interval_refine first/last with open min/max") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the PCM core calls snd_pcm_unlink() always unconditionally
at closing a stream. However, since snd_pcm_unlink() invokes the
global rwsem down, the lock can be easily contended. More badly, when
a thread runs in a high priority RT-FIFO, it may stall at spinning.
Basically the call of snd_pcm_unlink() is required only for the linked
streams that are already rare occasion. For normal use cases, this
code path is fairly superfluous.
As an optimization (and also as a workaround for the RT problem
above in normal situations without linked streams), this patch adds a
check before calling snd_pcm_unlink() and calls it only when needed.
Commit 67ec1072b053 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM
stream") fixes deadlock for non-atomic PCM stream. But, This patch
causes antother stuck.
If writer is RT thread and reader is a normal thread, the reader
thread will be difficult to get scheduled. It may not give chance to
release readlocks and writer gets stuck for a long time if they are
pinned to single cpu.
The deadlock described in the previous commit is because the linux
rwsem queues like a FIFO. So, we might need non-FIFO writelock, not
non-block one.
My suggestion is that the writer gives reader a chance to be scheduled
by using the minimum msleep() instaed of spinning without blocking by
writer. Also, The *_nonblock may be changed to *_nonfifo appropriately
to this concept.
In terms of performance, when trylock is failed, this minimum periodic
msleep will have the same performance as the tick-based
schedule()/wake_up_q().
[ Although this has a fairly high performance penalty, the relevant
code path became already rare due to the previous commit ("ALSA:
pcm: Call snd_pcm_unlink() conditionally at closing"). That is, now
this unconditional msleep appears only when using linked streams,
and this must be a rare case. So we accept this as a quick
workaround until finding a more suitable one -- tiwai ]
If a USB sound card reports 0 interfaces, an error condition is triggered
and the function usb_audio_probe errors out. In the error path, there was a
use-after-free vulnerability where the memory object of the card was first
freed, followed by a decrement of the number of active chips. Moving the
decrement above the atomic_dec fixes the UAF.
[ The original problem was introduced in 3.1 kernel, while it was
developed in a different form. The Fixes tag below indicates the
original commit but it doesn't mean that the patch is applicable
cleanly. -- tiwai ]
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 63f53dea0c98 ("mm: warn about allocations which stall for too
long") was a great step for reducing possibility of silent hang up
problem caused by memory allocation stalls. But this commit reverts it,
for it is possible to trigger OOM lockup and/or soft lockups when many
threads concurrently called warn_alloc() (in order to warn about memory
allocation stalls) due to current implementation of printk(), and it is
difficult to obtain useful information due to limitation of synchronous
warning approach.
Current printk() implementation flushes all pending logs using the
context of a thread which called console_unlock(). printk() should be
able to flush all pending logs eventually unless somebody continues
appending to printk() buffer.
Since warn_alloc() started appending to printk() buffer while waiting
for oom_kill_process() to make forward progress when oom_kill_process()
is processing pending logs, it became possible for warn_alloc() to force
oom_kill_process() loop inside printk(). As a result, warn_alloc()
significantly increased possibility of preventing oom_kill_process()
from making forward progress.
---------- Pseudo code start ----------
Before warn_alloc() was introduced:
retry:
if (mutex_trylock(&oom_lock)) {
while (atomic_read(&printk_pending_logs) > 0) {
atomic_dec(&printk_pending_logs);
print_one_log();
}
// Send SIGKILL here.
mutex_unlock(&oom_lock)
}
goto retry;
After warn_alloc() was introduced:
retry:
if (mutex_trylock(&oom_lock)) {
while (atomic_read(&printk_pending_logs) > 0) {
atomic_dec(&printk_pending_logs);
print_one_log();
}
// Send SIGKILL here.
mutex_unlock(&oom_lock)
} else if (waited_for_10seconds()) {
atomic_inc(&printk_pending_logs);
}
goto retry;
---------- Pseudo code end ----------
Although waited_for_10seconds() becomes true once per 10 seconds,
unbounded number of threads can call waited_for_10seconds() at the same
time. Also, since threads doing waited_for_10seconds() keep doing
almost busy loop, the thread doing print_one_log() can use little CPU
resource. Therefore, this situation can be simplified like
when printk() is called faster than print_one_log() can process a log.
One of possible mitigation would be to introduce a new lock in order to
make sure that no other series of printk() (either oom_kill_process() or
warn_alloc()) can append to printk() buffer when one series of printk()
(either oom_kill_process() or warn_alloc()) is already in progress.
Such serialization will also help obtaining kernel messages in readable
form.
But this commit does not go that direction, for we don't want to
introduce a new lock dependency, and we unlikely be able to obtain
useful information even if we serialized oom_kill_process() and
warn_alloc().
Synchronous approach is prone to unexpected results (e.g. too late [1],
too frequent [2], overlooked [3]). As far as I know, warn_alloc() never
helped with providing information other than "something is going wrong".
I want to consider asynchronous approach which can obtain information
during stalls with possibly relevant threads (e.g. the owner of
oom_lock and kswapd-like threads) and serve as a trigger for actions
(e.g. turn on/off tracepoints, ask libvirt daemon to take a memory dump
of stalling KVM guest for diagnostic purpose).
This commit temporarily loses ability to report e.g. OOM lockup due to
unable to invoke the OOM killer due to !__GFP_FS allocation request.
But asynchronous approach will be able to detect such situation and emit
warning. Thus, let's remove warn_alloc().
[1] https://bugzilla.kernel.org/show_bug.cgi?id=192981
[2] http://lkml.kernel.org/r/CAM_iQpWuPVGc2ky8M-9yukECtS+zKjiDasNymX7rMcBjBFyM_A@mail.gmail.com
[3] commit db73ee0d46379922 ("mm, vmscan: do not loop on too_many_isolated for ever"))
Link: http://lkml.kernel.org/r/1509017339-4802-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: yuwang.yuwang <yuwang.yuwang@alibaba-inc.com> Reported-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
team_notify_peers() will send ARP and NA to notify peers. team_mcast_rejoin()
will send multicast join group message to notify peers. We should do this when
enabling/changed to a new port. But it doesn't make sense to do it when a port
is disabled.
On the other hand, when we set mcast_rejoin_count to 2, and do a failover,
team_port_disable() will increase mcast_rejoin.count_pending to 2 and then
team_port_enable() will increase mcast_rejoin.count_pending to 4. We will send
4 mcast rejoin messages at latest, which will make user confused. The same
with notify_peers.count.
Fix it by deleting team_notify_peers() and team_mcast_rejoin() in
team_port_disable().
Reported-by: Liang Li <liali@redhat.com> Fixes: fc423ff00df3a ("team: add peer notification") Fixes: 492b200efdd20 ("team: add support for sending multicast rejoins") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.
In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".
[V2]
Remove unnecessary curly braces.
Signed-off-by: Vincent Chen <vincentc@andestech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration") Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address bffd3000
[ 11.209254] pgd = e463054d
[ 11.211948] [bffd3000] *pgd=2fffb811, *pte=00000000, *ppte=00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
Reported-by: Adrian Amborzewicz <adrian.ambrozewicz@intel.com> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3edfb7bd76bd ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize the uid variable to zero to avoid the compilation warning.
Fixes: 7a89399ffad7 ("net/mlx4: Add mlx4_bitmap zone allocator") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This register should have been programmed with the physical address
of the memory location containing the shadow tail pointer for
the guest virtual APIC log instead of the base address.
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net> Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
In the case where eq->fw->size > PAGE_SIZE the error return rc
is being set to EINVAL however this is being overwritten to
rc = req->fw->size because the error exit path via label 'out' is
not being taken. Fix this by adding the jump to the error exit
path 'out'.
Detected by CoverityScan, CID#1453465 ("Unused value")
Fixes: c92316bf8e94 ("test_firmware: add batched firmware tests") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9413b43 ("can: rcar_can: support all input clocks") Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8ec ("brcmfmac: fix for proper support of 160MHz bandwidth") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While there are issues related to object lifetime management, unregister the
media device first when the driver is being unbound. This is slightly
safer.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
passing the strlen() of the source string as the destination
length is pointless, and gcc-8 now warns about it:
drivers/net/ethernet/qlogic/qed/qed_debug.c: In function 'qed_grc_dump':
include/linux/string.h:253: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
This changes qed_grc_dump_big_ram() to instead uses the length of
the destination buffer, and use strscpy() to guarantee nul-termination.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is caused by the nr_indirectly_reclaimable counter,
which is hidden from the /proc/vmstat, but not from the
/proc/zoneinfo. Let's fix this inconsistency and hide the
counter from /proc/zoneinfo exactly as from /proc/vmstat.
BTW, in 4.19+ the counter has been renamed and exported by
the commit b29940c1abd7 ("mm: rename and change semantics of
nr_indirectly_reclaimable_bytes"), so there is no such a problem
anymore.
Cc: <stable@vger.kernel.org> # 4.14.x-4.18.x Fixes: 7aaf77272358 ("mm: don't show nr_indirectly_reclaimable in /proc/vmstat") Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sensor is all setup, bind, resetted, acked, etc... every single second.
That was the way to workaround a problem with the interrupt bouncing again and
again.
With the following changes, we fix all in one:
- Do the setup, one time, at probe time
- Add the IRQF_ONESHOT, ack the interrupt in the threaded handler
- Remove the interrupt handler
- Set the correct value for the LAG register
- Remove all the irq_enabled stuff in the code as the interruption
handling is fixed
- Remove the 3ms delay
- Reorder the initialization routine to be in the right order
It ends up to a nicer code and more efficient, the 3-5ms delay is removed from
the get_temp() path.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by: Leo Yan <leo.yan@linaro.org> Tested-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TEMP0_CFG configuration register contains different field to set up the
temperature controller. However in the code, nothing prevents a setup to
overwrite the previous one: eg. writing the hdak value overwrites the sensor
selection, the sensor selection overwrites the hdak value.
In order to prevent such thing, use a regmap-like mechanism by reading the
value before, set the corresponding bits and write the result.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The threaded interrupt inspect the sensors structure to look in the temp
threshold field, but this field is read-only in all the code, except in the
probe function before the threaded interrupt is set. In other words there
is not race window in the threaded interrupt when reading the field value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By essence, the tsensor does not really support multiple sensor at the same
time. It allows to set a sensor and use it to get the temperature, another
sensor could be switched but with a delay of 3-5ms. It is difficult to read
simultaneously several sensors without a big delay.
Today, just one sensor is used, it is not necessary to deal with multiple
sensors in the code. Remove them and if it is needed in the future add them
on top of a code which will be clean up in the meantime.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by: Leo Yan <leo.yan@linaro.org> Acked-by: Wangtao (Kevin, Kirin) <kevin.wangtao@hisilicon.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If all pages are deleted from the mapping by memory reclaim and also
moved to the cleancache:
__delete_from_page_cache
(no shadow case)
unaccount_page_cache_page
cleancache_put_page
page_cache_delete
mapping->nrpages -= nr
(nrpages becomes 0)
We don't clean the cleancache for an inode after final file truncation
(removal).
truncate_inode_pages_final
check (nrpages || nrexceptional) is false
no truncate_inode_pages
no cleancache_invalidate_inode(mapping)
These way when reading the new file created with same inode we may get
these trash leftover pages from cleancache and see wrong data instead of
the contents of the new file.
Fix it by always doing truncate_inode_pages which is already ready for
nrpages == 0 && nrexceptional == 0 case and just invalidates inode.
[akpm@linux-foundation.org: add comment, per Jan] Link: http://lkml.kernel.org/r/20181112095734.17979-1-ptikhomirov@virtuozzo.com Fixes: commit 91b0abe36a7b ("mm + fs: store shadow entries in page cache") Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Reviewed-by: Vasily Averin <vvs@virtuozzo.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Matthew Wilcox <willy@infradead.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bb475230b8e5 ("reset: make optional functions really optional")
gave a new meaning to _get_optional variants.
The differentiation by WARN_ON() is not needed any more. We already
have inconsistency about this; (devm_)reset_control_get_exclusive()
has WARN_ON() check, but of_reset_control_get_exclusive() does not.
Commit bb475230b8e5 ("reset: make optional functions really optional")
converted *_get_optional* functions, but device_reset_optional() was
left behind. Convert it in the same way.
Commit c26f6c615788 ("udf: Fix conversion of 'dstring' fields to UTF8")
started to be more strict when checking whether converted strings are
properly formatted. Sudip reports that there are DVDs where the volume
identification string is actually too long - UDF reports:
during mount and fails the mount. This is mostly harmless failure as we
don't need volume identification (and even less volume set
identification) for anything. So just truncate the volume identification
string if it is too long and replace it with 'Invalid' if we just cannot
convert it for other reasons. This keeps slightly incorrect media still
mountable.
CC: stable@vger.kernel.org Fixes: c26f6c615788 ("udf: Fix conversion of 'dstring' fields to UTF8") Reported-and-tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.
In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.
This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.
Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.
When a metadata read is served the endio routine btree_readpage_end_io_hook
is called which eventually runs the tree-checker. If tree-checker fails
to validate the read eb then it sets EXTENT_BUFFER_CORRUPT flag. This
leads to btree_read_extent_buffer_pages wrongly assuming that all
available copies of this extent buffer are wrong and failing prematurely.
Fix this modify btree_read_extent_buffer_pages to read all copies of
the data.
This failure was exhibitted in xfstests btrfs/124 which would
spuriously fail its balance operations. The reason was that when balance
was run following re-introduction of the missing raid1 disk
__btrfs_map_block would map the read request to stripe 0, which
corresponded to devid 2 (the disk which is being removed in the test):
This caused read requests for a checksum item that to be routed to the
stale disk which triggered the aforementioned logic involving
EXTENT_BUFFER_CORRUPT flag. This then triggered cascading failures of
the balance operation.
Fixes: a826d6dcb32d ("Btrfs: check items for correctness as we search") CC: stable@vger.kernel.org # 4.4+ Suggested-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
bg_start=12018974720 bg_len=10888413184, invalid block group size, \
have 10888413184 expect (0, 10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
The cros_ec_keyb_bs array lists buttons and switches together, expecting
that its users will match the appropriate type and bit fields. But
cros_ec_keyb_register_bs() only checks the 'bit' field, which causes
misreported input capabilities in some cases. For example, tablets
(e.g., Scarlet -- a.k.a. Acer Chromebook Tab 10) were reporting a SW_LID
capability, because EC_MKBP_POWER_BUTTON and EC_MKBP_LID_OPEN happen to
share the same bit.
(This has comedic effect on a tablet, in which a power-management daemon
then thinks this "lid" is closed, and so puts the system to sleep as
soon as it boots!)
To fix this, check both the 'ev_type' and 'bit' fields before reporting
the capability.
Tested with a lid (Kevin / Samsung Chromebook Plus) and without a lid
(Scarlet / Acer Chromebook Tab 10).
This error got introduced when porting the feature from the downstream
Chromium OS kernel to be upstreamed.
"of_get_named_gpio()" returns a negative error value if it fails
and drivers should check for this. This missing check was now
added to the matrix_keypad driver.
In my case "of_get_named_gpio()" returned -EPROBE_DEFER because
the referenced GPIOs belong to an I/O expander, which was not yet
probed at the point in time when the matrix_keypad driver was
loading. Because the driver did not check for errors from the
"of_get_named_gpio()" routine, it was assuming that "-EPROBE_DEFER"
is actually a GPIO number and continued as usual, which led to further
errors like this later on:
Note that the "GPIO number" -517 in the error message above is
actually "-EPROBE_DEFER".
As part of the patch a misleading error message "no platform data defined"
was also removed. This does not lead to information loss because the other
error paths in matrix_keypad_parse_dt() already print an error.
Signed-off-by: Christian Hoff <christian_hoff@gmx.net> Suggested-by: Sebastian Reichel <sre@kernel.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Use the new of_get_compatible_child() helper to lookup the legacy
pwrlevels child node instead of using of_find_compatible_node(), which
searches the entire tree from a given start node and thus can return an
unrelated (i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the probed device's node).
While at it, also fix the related child-node reference leak.
Fixes: e2af8b6b0ca1 ("drm/msm: gpu: Use OPP tables if we can") Cc: stable <stable@vger.kernel.org> # 4.12 Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org>
[ johan: backport to 4.14 ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
After 2dd453168643 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd453168643 ("kgdboc: Fix restrict error") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meddlesome gcc warns about the possible shortname string in
trident driver code:
sound/pci/trident/trident.c: In function ‘snd_trident_probe’:
sound/pci/trident/trident.c:126:2: warning: ‘strcat’ accessing 17 or more bytes at offsets 36 and 20 may overlap 1 byte at offset 36 [-Wrestrict]
strcat(card->shortname, card->driver);
It happens since gcc calculates the possible string size from
card->driver, but this can't be true since we did set the string just
before that, and they are much shorter.
For shutting it up, use the exactly same string set to card->driver
for strcat() to card->shortname, too.
After the VMA to register the uffd onto is found, check that it has
VM_MAYWRITE set before allowing registration. This way we inherit all
common code checks before allowing to fill file holes in shmem and
hugetlbfs with UFFDIO_COPY.
The userfaultfd memory model is not applicable for readonly files unless
it's a MAP_PRIVATE.
Link: http://lkml.kernel.org/r/20181126173452.26955-4-aarcange@redhat.com Fixes: ff62a3421044 ("hugetlb: implement memfd sealing") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Reported-by: Jann Horn <jannh@google.com> Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Cc: <stable@vger.kernel.org> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanly fill memory for "vendor" and "model" with 0-bytes for the
"compatible" case rather than adding only a single 0 byte. This
simplifies the devinfo code a a bit, and avoids mistakes in other places
of the code (not in current upstream, but we had one such mistake in the
SUSE kernel).
[mkp: applied by hand and added braces]
Signed-off-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the page dirty if VM_WRITE is not set because in such case the pte
won't be marked dirty and the page would be reclaimed without writepage
(i.e. swapout in the shmem case).
This was found by source review. Most apps (certainly including QEMU)
only use UFFDIO_COPY on PROT_READ|PROT_WRITE mappings or the app can't
modify the memory in the first place. This is for correctness and it
could help the non cooperative use case to avoid unexpected data loss.
Link: http://lkml.kernel.org/r/20181126173452.26955-6-aarcange@redhat.com Reviewed-by: Hugh Dickins <hughd@google.com> Cc: stable@vger.kernel.org Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Reported-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log