Driver is missing the interrupts if two requests are queued up at the same
time as the interrupt handler is servicing a request that was just
delivered.
The ISR clears the interrupt at the end but it could be clearing the
interrupt for an outstanding event. Therefore, second interrupt never
arrives.
Clear the interrupt first and then check for completions.
Also, make sure that request start and interrupt clear do not overlap in
time by using a spinlock.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A warning that I thought I had fixed before occasionally comes
back in rare randconfig builds (I found 7 instances in the last
100000 builds, originally it was much more frequent):
drivers/infiniband/hw/mlx5/mr.c: In function 'mlx5_ib_reg_user_mr':
drivers/infiniband/hw/mlx5/mr.c:1229:5: error: 'order' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (order <= mr_cache_max_order(dev)) {
^
drivers/infiniband/hw/mlx5/mr.c:1247:8: error: 'ncont' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/infiniband/hw/mlx5/mr.c:1247:8: error: 'page_shift' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/infiniband/hw/mlx5/mr.c:1260:2: error: 'npages' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I've looked at all those findings again and noticed that they are all
with CONFIG_INFINIBAND_USER_MEM=n, which means ib_umem_get() returns
an error unconditionally and we never initialize or use those variables.
This triggers a condition in gcc iff mr_umem_get() is partially but not
entirely inlined, which in turn depends on the exact combination of
optimization settings. This is a known problem with gcc, with no
easy solution in the compiler, so this adds another workaround that
should be more reliable than my previous attempt.
Returning an error from mlx5_ib_reg_user_mr() earlier means that we
can completely bypass the logic that caused the warning, the compiler
can now see that the variable is never accessed.
Custom policies can require file signatures based on LSM labels. These
files are normally created and only afterwards labeled, requiring them
to be signed.
Instead of requiring file signatures based on LSM labels, entire
filesystems could require file signatures. In this case, we need the
ability of writing new files without requiring file signatures.
The definition of a "new" file was originally defined as any file with
a length of zero. Subsequent patches redefined a "new" file to be based
on the FILE_CREATE open flag. By combining the open flag with a file
size of zero, this patch relaxes the file signature requirement.
Things can explode for locktorture if the user does combinations
of nwriters_stress=0 nreaders_stress=0. Fix this by not assuming
we always want to torture writer threads.
Reported-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Jeremy Linton <jeremy.linton@arm.com> Tested-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'configinit.sh' script checks the format of optional argument for the
build directory, printing an error message if the format is not valid.
However, the error message uses the wrong variable, indicating an empty
string even though the user entered a non-empty (but erroneous) string.
This commit fixes the script to use the correct variable.
Fixes: c87b9c601ac8 ("rcutorture: Add KVM-based test framework") Signed-off-by: SeongJae Park <sj38.park@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <amit.sikka@ericsson.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c84 ("mmc: mmc_test: Disable Command Queue while mmc_test is used") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix below warnings on ARMv7 by using %zu for printing size_t values:
drivers/crypto/caam/caamalg_qi.c: In function aead_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:417:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:672:16: note: in expansion of macro CAAM_QI_MAX_AEAD_SG
qm_sg_ents, CAAM_QI_MAX_AEAD_SG);
^
drivers/crypto/caam/caamalg_qi.c: In function ablkcipher_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:440:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:909:16: note: in expansion of macro CAAM_QI_MAX_ABLKCIPHER_SG
qm_sg_ents, CAAM_QI_MAX_ABLKCIPHER_SG);
^
drivers/crypto/caam/caamalg_qi.c: In function ablkcipher_giv_edesc_alloc:
drivers/crypto/caam/caamalg_qi.c:440:17: warning: format %lu expects argument of type long unsigned int, but argument 4 has type unsigned int [-Wformat=]
sizeof(struct qm_sg_entry))
^
drivers/crypto/caam/caamalg_qi.c:1062:16: note: in expansion of macro CAAM_QI_MAX_ABLKCIPHER_SG
qm_sg_ents, CAAM_QI_MAX_ABLKCIPHER_SG);
^
Fixes: eb9ba37dc15a ("crypto: caam/qi - handle large number of S/Gs case") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ieee80211_setup_sdata() we check if the interface type is valid
and, if not, call BUG(). This should never happen, but if there is
something wrong with the code, it will not be caught until the bug
happens when an interface is being set up. Calling BUG() is too
extreme for this and a WARN_ON() would be better used instead. Change
that.
Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll,
only if PS_ENABLED was set before.
This is required due to commit c9491367b759 ("mac80211: always update the
PM state of a peer on MGMT / DATA frames") that enforces the ap to
check only mgmt/data frames ps bit, and then update station's power save
accordingly.
When sending only ps-poll (control frame) the ap will not be aware that
the station entered power save.
Setting ps enable before triggering ps_poll, will send NDP with PM bit
enabled first.
Before accessing the GGTT we must flush the PTE writes and make them
visible to the chipset, or else the indirect access may end up in the
wrong page. In commit 3497971a71d8 ("agp/intel: Flush chipset writes
after updating a single PTE"), we noticed corruption of the uploads for
pwrite and for capturing GPU error states, but it was presumed that the
explicit calls to intel_gtt_chipset_flush() were sufficient for the
execbuffer path. However, we have not been flushing the chipset between
the PTE writes and access via the GTT itself.
For simplicity, do the flush after any PTE update rather than try and
batch the flushes on a just-in-time basis.
References: 3497971a71d8 ("agp/intel: Flush chipset writes after updating a single PTE") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: drm-intel-fixes@lists.freedesktop.org Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171208214616.30147-1-chris@chris-wilson.co.uk Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.
On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
When an interrupt is returning to a soft-disabled context (which can
happen for non-maskable interrupts or synchronous interrupts), it goes
through the motions of soft-disabling again, including calling
TRACE_DISABLE_INTS (i.e., trace_hardirqs_off()).
This is not necessary, because we must already be soft-disabled in the
interrupt context, it also may be causing crashes in the irq tracing
code to re-enter as an nmi. Replace it with a warning to ensure that
soft-interrupts are still disabled.
Fixes: 7c0482e3d055 ("powerpc/irq: Fix another case of lazy IRQ state getting out of sync") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC didn't insert a nop after the branch to net_set_todo() because it's
a sibling call, so it never returns. The nop isn't needed after the
branch in that case.
Kobject created using kobject_create_and_add() can be freed using
kobject_put() when there is no referenece any more. However,
kobject memory allocated with kzalloc() has to set up a release
callback in order to free it when the counter decreases to 0.
Otherwise it causes memory leak.
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qdisc_graft_qdisc a "new" qdisc is attached and the 'qdisc_destroy'
operation is called on the old qdisc. The destroy operation will wait
a rcu grace period and call qdisc_rcu_free(). At which point
gso_cpu_skb is free'd along with all stats so no need to zero stats
and gso_cpu_skb from the graft operation itself.
Further after dropping the qdisc locks we can not continue to call
qdisc_reset before waiting an rcu grace period so that the qdisc is
detached from all cpus. By removing the qdisc_reset() here we get
the correct property of waiting an rcu grace period and letting the
qdisc_destroy operation clean up the qdisc correctly.
Note, a refcnt greater than 1 would cause the destroy operation to
be aborted however if this ever happened the reference to the qdisc
would be lost and we would have a memory leak.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 39e6c8208d7b ("net: solve a NAPI race") napi has been able
to be rescheduled within napi_complete_done() even in non-busypoll case,
but virtnet_poll() always enabled interrupts before complete, and when
napi was rescheduled within napi_complete_done() it did not disable
interrupts.
This caused more interrupts when event idx is disabled.
According to commit cbdadbbf0c79 ("virtio_net: fix race in RX VQ
processing") we cannot place virtqueue_enable_cb_prepare() after
NAPI_STATE_SCHED is cleared, so disable interrupts again if
napi_complete_done() returned false.
Tested with vhost-user of OVS 2.7 on host, which does not have the event
idx feature.
* Before patch:
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
Interrupts on guest: 4941299
Packets/interrupt: 6.64
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array. The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.
Fixes: ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The raid set size is being revalidated unconditionally before a
reshaping conversion is started. MD requires the size to only be
reduced in case of a stripe removing (i.e. shrinking) reshape but not
when growing because the raid array has to stay small until after the
growing reshape finishes.
Fix by avoiding the size revalidation in preresume unless a shrinking
reshape is requested.
When used as part of a display pipeline, the VSP is stopped and
restarted explicitly by the DU from its suspend and resume handlers.
There is thus no need to stop or restart pipelines in the VSP suspend
and resume handlers, and doing so would cause the hardware to be
left in a misconfigured state.
Ensure that the VSP suspend and resume handlers do not affect DRM-based
pipelines.
Commit 4b2d9fe87950 ("staging: fsl-dpaa2/eth: Extra headroom in RX
buffers") removes the software annotation (SWA) area from the RX
buffer layout, as it's not used by anyone, but fails to update the
macros for accessing hardware annotation (HWA) fields, which is
right after the SWA in the buffer headroom.
This may lead to some frame annotation status fields (e.g. indication
if L3/L4 checksum is valid) to be read incorrectly.
Turn the accessor macros into inline functions and add a bool param
to specify if SWA is present or not.
Since scsi_get_device_flags_keyed() callers do not check whether or not
the returned value is an error code, change that function such that it
returns a flags value even if the 'key' argument is invalid. Note:
since commit 28a0bc4120d3 ("scsi: sd: Implement blacklist option for
WRITE SAME w/ UNMAP") bit 31 is a valid device information flag so
checking whether bit 31 is set in the return value is not sufficient to
tell the difference between an error code and a flags value.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e8af (spi: sunxi: Add Allwinner A31 SPI controller driver) Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indeed musl doesn't define old SIGCLD signal name but only new one SIGCHLD.
SIGCHLD is the new POSIX name for that signal so it doesn't change
anything on other libcs.
This fixes this kind of build error:
usbipd.c: In function ‘set_signal’:
usbipd.c:459:12: error: 'SIGCLD' undeclared (first use in this function)
sigaction(SIGCLD, &act, NULL);
^~~~~~
usbipd.c:459:12: note: each undeclared identifier is reported only once
for each function it appears in
Makefile:407: recipe for target 'usbipd.o' failed
make[3]: *** [usbipd.o] Error 1
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(1) Change virtual interface operation in cfg80211 process reset and
reinitilize private data structure.
(2) Scan result event processed in main process will dereference private
data structure concurrently, ocassionly crash the kernel.
The cornel case could be trigger by below steps:
(1) wpa_cli mlan0 scan
(2) ./hostapd mlan0.conf
Cfg80211 asynchronous scan procedure is not all the time operated
under rtnl lock, here we add the protect to serialize the cfg80211
scan and change_virtual interface operation.
Signed-off-by: Limin Zhu <liminzhu@marvell.com> Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:160 bnxt_tc_parse_actions()
error: uninitialized symbol 'rc'.
"rc" is either uninitialized or set to zero here so we can just remove
the check.
Fixes: 8c95f773b4a3 ("bnxt_en: add support for Flower based vxlan encap/decap offload") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a bug introduced by AMDGPU_GEM_CREATE_EXPLICIT_SYNC. We still need
to wait for pipelined moves in the shared fences list.
v2: fix typo
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Andres Rodriguez <andresx7@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We might erroneously get to error dumping code when the
device is already stopped.
In that case the driver will detect a defective value and will try to
reset the HW, assuming it is only a bus issue. The driver than
proceeds with the dumping.
The result has two side effects:
1. The device won't be stopped again, since the transport status is
already stopped, so the device remains powered on while it actually
should be stopped.
2. The dump in that case is completely garbaged and useless.
Detect and avoid this. It will also make debugging such issues
easier.
The command 'perf annotate' parses the output of objdump and also
investigates the comments produced by objdump. For example the
output of objdump produces (on x86):
and the function mov__parse() is called to investigate the complete
line. Mov__parse() breaks this line into several parts and finally
calls function comment__symbol() to parse the data after the comment
character '#'. Comment__symbol() expects a hexadecimal address followed
by a symbol in '<' and '>' brackets.
However the 2nd parameter given to function comment__symbol()
always points to the comment character '#'. The address parsing
always returns 0 because the character '#' is not a digit and
strtoull() fails without being noticed.
Fix this by advancing the second parameter to function comment__symbol()
by one byte before invocation and add an error check after strtoull()
has been called.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Acked-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Fixes: 6de783b6f50f ("perf annotate: Resolve symbols using objdump comment") Link: http://lkml.kernel.org/r/20171128075632.72182-1-tmricht@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug introduced with commit d9f8dfa9baf9 ("perf
annotate s390: Implement jump types for perf annotate").
'perf annotate' displays annotated assembler output by reading output of
command objdump and parsing the disassembled lines. For each shown
mnemonic this function sequence is executed:
The s390x specific function assigned to function pointer
associate_instruction_ops refers to function s390__associate_ins_ops().
This function checks for supported mnemonics and assigns a NULL pointer
to unsupported mnemonics. However even the NULL pointer is added to the
architecture dependend instruction array.
This leads to an extremely large architecture instruction array
(due to array resize logic in function arch__grow_instructions()).
Depending on the objdump output being parsed the array can end up
with several ten-thousand elements.
This patch checks if a mnemonic is supported and only adds supported
ones into the architecture instruction array. The array does not contain
elements with NULL pointers anymore.
Before the patch (With some debug printf output):
[root@s35lp76 perf]# time ./perf annotate --stdio > /tmp/xxxbb
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR16 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7795 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E.
This patch adds can_clk function to r8a7743/r8a7791 which is cleaner,
and allows for independent configuration.
We keep the can_clk* pins definitions from within can0_groups and
can1_groups for uniformity and backwards compatibility.
We are testing if there is a match with the ses device in a loop by
calling ses_match_to_enclosure(), which will issue scsi receive
diagnostics commands to the ses device for every device on the same
host. On one of our boxes with 840 disks, it takes a long time to load
the driver:
[root@g1b-oss06 ~]# time modprobe ses
real 40m48.247s
user 0m0.001s
sys 0m0.196s
With the patch:
[root@g1b-oss06 ~]# time modprobe ses
real 0m17.915s
user 0m0.008s
sys 0m0.053s
Note that we still need to refresh page 10 when we see a new disk to
create the link.
Signed-off-by: Li Dongyang <dongyang.li@anu.edu.au> Tested-by: Jason Ozolins <jason.ozolins@hpe.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is unloading, the nvme transport could be in the process
of submitting new requests, will send abort requests to terminate
associations, or may make LS-related requests. The driver's abort and
request entry points currently is ignorant of the unloading state and is
starting the requests even though the infrastructure to complete them
continues to teardown.
Change the entry points for new requests to check whether unloading and
if so, reject the requests. Abort routines check unloading, and if so,
noop the request. An abort is noop'd as the teardown paths are already
aborting/terminating the io outstanding at the time the teardown
initiated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Monk Liu <Monk.Liu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AMD platforms, under certain conditions insn_len may be zero on #NPF.
This can happen if a guest gets a page-fault on data access but the HW
table walker is not able to read the instruction page (e.g instruction
page is not present in memory).
Typically, when insn_len is zero, x86_emulate_instruction() walks the
guest page table and fetches the instruction bytes from guest memory.
When SEV is enabled, the guest memory is encrypted with guest-specific
key hence hypervisor will not able to fetch the instruction bytes.
In those cases we simply restart the guest.
I have encountered this issue when running kernbench inside the guest.
It is possible to remove a cpufreq governor module after
cpufreq_parse_governor() has returned success in
store_scaling_governor() and before cpufreq_set_policy()
acquires a reference to it, because the governor list is
not protected during that period and nothing prevents the
governor from being unregistered then.
Prevent that from happening by acquiring an extra reference
to the governor module temporarily in cpufreq_parse_governor(),
under cpufreq_governor_mutex, and dropping it in
store_scaling_governor(), when cpufreq_set_policy() returns.
Note that the second cpufreq_parse_governor() call site is fine,
because it only cares about the policy member of new_policy.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The etnaviv driver causes a link failure if it is built-in but THERMAL
is built as a module:
drivers/gpu/drm/etnaviv/etnaviv_gpu.o: In function `etnaviv_gpu_bind':
etnaviv_gpu.c:(.text+0x4c4): undefined reference to `thermal_of_cooling_device_register'
etnaviv_gpu.c:(.text+0x600): undefined reference to `thermal_cooling_device_unregister'
drivers/gpu/drm/etnaviv/etnaviv_gpu.o: In function `etnaviv_gpu_unbind':
etnaviv_gpu.c:(.text+0x2aac): undefined reference to `thermal_cooling_device_unregister'
Adding a Kconfig dependency on THERMAL || !THERMAL to avoid this causes
a dependency loop on x86_64:
drivers/gpu/drm/tve200/Kconfig:1:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/tve200/Kconfig:1: symbol DRM_TVE200 depends on CMA
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
mm/Kconfig:489: symbol CMA is selected by DRM_ETNAVIV
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/etnaviv/Kconfig:2: symbol DRM_ETNAVIV depends on THERMAL
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/thermal/Kconfig:5: symbol THERMAL is selected by ACPI_VIDEO
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/acpi/Kconfig:189: symbol ACPI_VIDEO is selected by BACKLIGHT_CLASS_DEVICE
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/video/backlight/Kconfig:158: symbol BACKLIGHT_CLASS_DEVICE is selected by DRM_PARADE_PS8622
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/bridge/Kconfig:62: symbol DRM_PARADE_PS8622 depends on DRM_BRIDGE
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpu/drm/bridge/Kconfig:1: symbol DRM_BRIDGE is selected by DRM_TVE200
To work around this, add a new option DRM_ETNAVIV_THERMAL to optionally
enable thermal throttling support and make DRM_ETNAVIV select THERMAL
at the same time.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs when we enable the backup battery charging, we should
go through the error handling path directly.
Before commit db43e6c473b5 ("ab8500-bm: Add usb power path support") this
was the case, but this commit has added some code between the last test and
the 'out' label.
So, in case of error, this added code is executed and the error may be
silently ignored.
Fix it by adding the missing 'goto out', as done in all other error
handling paths.
Fixes: db43e6c473b5 ("ab8500-bm: Add usb power path support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer returned by of_device_get_match_data() doesn't have the same
size as u32 on 64-bit architectures, causing a compile warning when
compile-testing the driver on such platform.
Cast the return value of of_device_get_match_data() to unsigned long and
then to u32 to silence this warning.
In case of wrap around, replay_esn->oseq_hi is not updated
before it is tested for it's actual value, leading function
to fail with overflow indication and packets being dropped.
This patch updates replay_esn->oseq_hi in the right place.
When vfs_submount was added the test to limit automounts from
filesystems that with s_user_ns != &init_user_ns accidentially left
in follow_automount. The test was never about any security concerns
and was always about how do we implement this for filesystems whose
s_user_ns != &init_user_ns.
At the moment this check makes no difference as there are no
filesystems that both set FS_USERNS_MOUNT and implement d_automount.
Remove this check now while I am thinking about it so there will not
be odd booby traps for someone who does want to make this combination
work.
vfs_submount still needs improvements to allow this combination to work,
and vfs_submount contains a check that presents a warning.
The autofs4 filesystem could be modified to set FS_USERNS_MOUNT and it would
need not work on this code path, as userspace performs the mounts.
Fixes: 93faccbbfa95 ("fs: Better permission checking for submounts") Fixes: aeaa4a79ff6a ("fs: Call d_automount with the filesystems creds") Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on T81 there are only 4 cores, hence setting max queue count to 4
would leave nothing for XDP_TX. This patch fixes this by doubling
max queue count in above scenarios.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: cjacob <cjacob@caviumnetworks.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Do not allow OPEN_SOURCE & OPEN_DRAIN flags in a single request. If
the hardware actually supports enabling both at the same time the
electrical result would be disastrous.
Currently it is possible to add or update socket policies, but
not clear them. Therefore, once a socket policy has been applied,
the socket cannot be used for unencrypted traffic.
This patch allows (privileged) users to clear socket policies by
passing in a NULL pointer and zero length argument to the
{IP,IPV6}_{IPSEC,XFRM}_POLICY setsockopts. This results in both
the incoming and outgoing policies being cleared.
The simple approach taken in this patch cannot clear socket
policies in only one direction. If desired this could be added
in the future, for example by continuing to pass in a length of
zero (which currently is guaranteed to return EMSGSIZE) and
making the policy be a pointer to an integer that contains one
of the XFRM_POLICY_{IN,OUT} enum values.
An alternative would have been to interpret the length as a
signed integer and use XFRM_POLICY_IN (i.e., 0) to clear the
input policy and -XFRM_POLICY_OUT (i.e., -1) to clear the output
policy.
The PERF_RECORD_USER_ events are synthesized by the tool to assist in
processing the PERF_RECORD_ ones generated by the kernel, the printing
of that information doesn't come with a perf_sample structure, so, when
dumping the event fields using 'perf report -D' there were columns that
end up not being printed.
To tidy up a bit this, fake a perf_sample structure with zeroes to have
the missing columns printed and avoid the occasional surprise with that.
We're currently calling ktime_to_timespec64() on stack garbage
hence the debug output for vblank timestamps also contains garbage.
Let's assing something to the ktime_t first before we go converting
it to a timespec.
While at it micro-optimize the ktime_to_timespec64() calls away
when vblank debugging isn't enabled.
Fixes: 67680d3c0464 ("drm: vblank: use ktime_t instead of timeval") Cc: Arnd Bergmann <arnd@arndb.de> Cc: Keith Packard <keithp@keithp.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171113150210.11311-1-ville.syrjala@linux.intel.com Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file /sys/module/firmware_class/parameters/path can be used
to set a custom firmware path. The fw_filesystem.sh script creates
a temporary directory to add a test firmware file to be used during
testing, in order for this to work it uses the custom path syfs file
and it was supposed to reset back the file on execution exit. The
script failed to do this due to a typo, it was using OLD_PATH instead
of OLD_FWPATH, since its inception since v3.17.
Its not as easy to just keep the old setting, it turns out that
resetting an empty setting won't actually do what we want, we need
to check if it was empty and set an empty space.
Without this we end up having the temporary path always set after
we run these tests.
The object info is being leaked on an error return path, fix this
by setting ret to -ENOMEM and exiting via the request_cleanup path
that will free info.
Detected by CoverityScan, CID#1408439 ("Resource Leak")
Fixes: c694b233295b ("crypto: cavium - Add the Virtual Function driver for CPT") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
crypto/keywrap.c: In function ‘crypto_kw_decrypt’:
crypto/keywrap.c:191: warning: integer constant is too large for ‘long’ type
crypto/keywrap.c: In function ‘crypto_kw_encrypt’:
crypto/keywrap.c:224: warning: integer constant is too large for ‘long’ type
If crypto_get_default_rng returns an error, the
function ecc_gen_privkey should return an error.
Instead, it currently tries to use the default_rng
nevertheless, thus creating a kernel panic with a
NULL pointer dereference.
Returning the error directly, as was supposedly
intended when looking at the code, fixes this.
Signed-off-by: Pierre Ducroquet <pinaraf@pinaraf.info> Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This splat cannot be generated by expedited grace periods because they
always invoke resched_cpu() on the current CPU, which is good because
expedited grace periods require that resched_cpu() unconditionally
succeed. However, other parts of RCU can tolerate resched_cpu() acting
as a no-op, at least as long as it doesn't happen too often.
This commit therefore makes resched_cpu() invoke resched_curr() only if
the CPU is either online or is the current CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rcutorture test suite occasionally provokes a splat due to invoking
rt_mutex_lock() which needs to boost the priority of a task currently
sitting on a runqueue that belongs to an offline CPU:
But the target task's priority has already been adjusted, so the only
purpose of switched_to_rt() invoking resched_curr() is to wake up the
CPU running some task that needs to be preempted by the boosted task.
But the CPU is offline, which presumably means that the task must be
migrated to some other CPU, and that this other CPU will undertake any
needed preemption at the time of migration. Because the runqueue lock
is held when resched_curr() is invoked, we know that the boosted task
cannot go anywhere, so it is not necessary to invoke resched_curr()
in this particular case.
This commit therefore makes switched_to_rt() refrain from invoking
resched_curr() when the target CPU is offline.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rs485 allows for robust half-duplex serial communication. It is often
implemented by attaching an rs485 transceiver to a UART. The UART's
RTS line is wired to the transceiver's Transmit Enable pin and
determines whether the transceiver is sending or receiving.
Examples for such transceivers are Maxim MAX13451E and TI SN65HVD1781A:
https://datasheets.maximintegrated.com/en/ds/MAX13450E-MAX13451E.pdf
http://www.ti.com/lit/ds/symlink/sn65hvd1781a-q1.pdf
In the devicetree, the transceiver itself is not represented, only the
UART is. A few rs485-specific dt-bindings already exist and these go
into the UART's device node.
This commit adds a binding to set the RTS polarity. Most (if not all)
transceivers require the Transmit Enable pin be driven high for sending,
but in some cases boards may negate the pin and RTS must then be driven
low. Consequently the polarity defaults to active high but can be
inverted with the newly added "rs485-rts-active-low" binding.
Document this binding in rs485.txt and in the two drivers fsl-imx-uart
and fsl-lpuart that are about to be amended with support for it.
Curiously, the omap_serial driver defaults to active low and already
supports an "rs485-rts-active-high" binding to invert the polarity.
This is left unchanged to retain compatibility, but the binding is
herewith documented.
Cc: Mark Jackson <mpfj@newflow.co.uk> Cc: Michał Oleszczyk <oleszczyk.m@gmail.com> Cc: Rafael Gago Castano <rgc@hms.se> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code looks up a USB device node from a given parent USB device but
never dropped its reference to the returned node.
As only the address of the node is used for a later matching, the
reference can be dropped immediately.
Note that this trigger implementation confuses the description of the
USB device connected to a port with the port itself (which does not have
a device-tree representation).
Fixes: 4f04c210d031 ("usb: core: read USB ports from DT in the usbport LED trigger driver") Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expectation in the FUSB302 driver is that a TX_SUCCESS event
should occur after a message has been sent, but before a GCRCSENT
event is raised to indicate successful receipt of a message from
the partner. However in some circumstances it is possible to see
the hardware raise a GCRCSENT event before a TX_SUCCESS event
is raised. The upshot of this is that the GCRCSENT handling portion
of code ends up reporting the GoodCRC message to TCPM because the
TX_SUCCESS event hasn't yet arrived to trigger a consumption of it.
When TX_SUCCESS is then raised by the chip it ends up consuming the
actual message that was meant for TCPM, and this incorrect sequence
results in a hard reset from TCPM.
To avoid this problem, this commit updates the message reading
code to check whether a GoodCRC message was received or not. Based
on this check it will either report that the previous transmission
has completed or it will pass the msg data to TCPM for futher
processing. This way the incorrect ordering of the events no longer
matters.
According to the datasheet, in Meson-GXBB/GXL series,
The clock gate bit for SARADC is HHI_GCLK_MPEG2 bit[22],
while clock gate bit for SANA is HHI_GCLK_MPEG0 bit[10].
Test passed at gxl-s905x-p212 board.
The following published datasheets are wrong and should be updated
[1] GXBB v1.1.4
[2] GXL v0.3_20170314
cec-clock is a fixed clock generator that is not controlled by i2c5 and
thus should not be a child of the i2c5 bus node. Rather, it should be
a child of the root node of the DT.
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
ELO devices have one Button usage in GenDesk field, which makes hid-input map
it to BTN_LEFT; that confuses userspace, which then considers the device to be
a mouse/touchpad instead of touchscreen.
Fix that by unmapping BTN_LEFT and keeping only BTN_TOUCH in place.
This fixes a typo where the intent was to assign to 'j' in order to
skip some number of bits in the dirty bitmap for a guest. The effect
of the typo is benign since it means we just iterate through all the
bits rather than skipping bits which we know will be zero. This issue
was found by Coverity.
HDMI 2.0 Appendix F suggest that we should keep sending the infoframe
when switching from 3D to 2D mode, even if the infoframe isn't strictly
necessary (ie. not needed to transmit the VIC or stereo information).
This is a workaround against some sinks that fail to realize that they
should switch from 3D to 2D mode when the source stop transmitting
the infoframe.
v2: Handle unpack() as well
Pull the length calculation into a helper
"Currently with fence-array, we have a potential deadlock situation. If
we fence_add_callback() on an array-fence, the array-fence's lock is
acquired first, and in it's ->enable_signaling() callback, it will install
cbs on it's array-member fences, so the array-member's lock is acquired
second.
But in the signal path, the array-member's lock is acquired first, and
the array-fence's lock acquired second."
Rob proposed either extensive changes to dma-fence to unnest the
fence-array signaling, or to defer the signaling onto a workqueue. This
is a more refined version of the later, that should keep the latency
of the fence signaling to a minimum by using an irq-work, which is
executed asap.
Reported-by: Rob Clark <robdclark@gmail.com> Suggested-by: Rob Clark <robdclark@gmail.com>
References: 1476635975-21981-1-git-send-email-robdclark@gmail.com Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Rob Clark <robdclark@gmail.com> Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20171114162719.30958-1-chris@chris-wilson.co.uk Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since drm_edid_to_eld() knows the connector type, we can set the type in
ELD while at it. Most connectors this gets called on are not DP
encoders, and with the HDMI type being 0, this does not change behaviour
for non-DP.
For i915 having this in place earlier would have saved a considerable
amount of debugging that lead to the fix 2d8f63297b9f ("drm/i915: always
update ELD connector type after get modes"). I don't see other drivers,
even the ones calling drm_edid_to_eld() on DP connectors, setting the
connector type in ELD.
Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Russell King <linux@armlinux.org.uk> Cc: CK Hu <ck.hu@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Mark Yao <mark.yao@rock-chips.com> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Eric Anholt <eric@anholt.net> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/d527b31619528c477c2c136f25cdf118bc0cfc1d.1509545641.git.jani.nikula@intel.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kvmppc_hpte_page_shifts function decodes the actual and base page
sizes for a HPTE, returning -1 if it doesn't recognize the page size
encoding. This then gets used as a shift amount in various places,
which is undefined behaviour. This was reported by Coverity.
In fact this should never occur, since we should only get HPTEs in the
HPT which have a recognized page size encoding. The only place where
this might not be true is in the call to kvmppc_actual_pgsz() near the
beginning of kvmppc_do_h_enter(), where we are validating the HPTE
value passed in from the guest.
So to fix this and eliminate the undefined behaviour, we make
kvmppc_hpte_page_shifts return 0 for unrecognized page size encodings,
and make kvmppc_actual_pgsz() detect that case and return 0 for the
page size, which will then cause kvmppc_do_h_enter() to return an
error and refuse to insert any HPTE with an unrecognized page size
encoding.
To ensure that we don't get undefined behaviour in compute_tlbie_rb(),
we take the 4k page size path for any unrecognized page size encoding.
This should never be hit in practice because it is only used on HPTE
values which have previously been checked for having a recognized
page size encoding.
Devices in "single finger hybrid mode" will send one report per finger,
on some devices only the first report of such a multi-packet frame will
contain a value for BTN_LEFT, in subsequent reports (if multiple fingers
are down) the value is always 0, causing hid-mt to report BTN_LEFT going
1 - 0 - 1 - 0 when pressing a clickpad and putting down a second finger.
This happens for example on USB 0603:0002 mt touchpads.
This commit fixes this by only reporting non touch fields for the first
packet of a (possibly) multi-packet frame.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 974488e4ce1e ("spi: imx: Fix failure path leak on GPIO request
error"), spi_bitbang_start() was moved later in the probe sequence. But
this doesn't work, as spi_bitbang_start() has to be called before
requesting GPIOs because the GPIO data in the spi master is populated when
the master is registed, and that doesn't happen until spi_bitbang_start()
is called. The default only works if one uses one CS.
So add a failure path call to spi_bitbang_stop() to fix the leak.
CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Mark Brown <broonie@kernel.org> CC: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one caller which checks whether rpi_touchscreen_i2c_read()
returns negative error codes. Currently it can't because negative
error codes are truncated to u8, but that's easy to fix if we change the
type to int.
Fixes: 2f733d6194bd ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/20171020002845.kar2wg7gqxg7tzqi@mwanda Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that commit 3229c18c0d6b2 'Fixes to "Implement iomap for
block_map"' introduced another bug in gfs2_iomap_begin that can cause
gfs2_block_map to set bh->b_size of an actual buffer to 0. This can
lead to arbitrary incorrect behavior including crashes or disk
corruption. Revert the incorrect part of that commit.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log