mlx4_delete_all_resources_for_slave in resource tracker should free all
memory allocated for a slave.
While releasing memory of fs_rule, it misses releasing memory of
fs_rule->mirr_mbox.
Fixes: 78efed275117 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports') Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We try to hold TX virtqueue mutex in vhost_net_rx_peek_head_len()
after RX virtqueue mutex is held in handle_rx(). This requires an
appropriate lock nesting notation to calm down deadlock detector.
Fixes: 0308813724606 ("vhost_net: basic polling support") Reported-by: syzbot+7f073540b1384a614e09@syzkaller.appspotmail.com Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same fix as in 'bonding: move dev_mc_sync after master_upper_dev_link
in bond_enslave' is needed for team driver.
The panic can be reproduced easily:
ip link add team1 type team
ip link set team1 up
ip link add link team1 vlan1 type vlan id 80
ip link set vlan1 master team1
Fixes: cb41c997d444 ("team: team should sync the port's uc/mc addrs when add a port") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this patch, when one packet is hashed into path [1]
(hash <= nh_upper_bound) and it's neigh is dead, it will try
path [2]. However, if path [2]'s neigh is alive but it's
hash > nh_upper_bound, it will not return this alive path.
This packet will never be sent even if path [2] is alive.
3.3.3.1/24:
nexthop via 1.1.1.254 dev eth1 weight 1 <--[1] (dead neigh)
nexthop via 2.2.2.254 dev eth2 weight 1 <--[2]
With sysctl_fib_multipath_use_neigh set is supposed to find an
available path respecting to the l3/l4 hash. But if there is
no available route with this hash, it should at least return
an alive route even with other hash.
This patch is to fix it by processing fib_multipath_use_neigh
earlier than the hash check, so that it will at least return
an alive route if there is when fib_multipath_use_neigh is
enabled. It's also compatible with before when there are alive
routes with the l3/l4 hash.
Fixes: a6db4494d218 ("net: ipv4: Consider failed nexthops in multipath routes") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vq log_base is the userspace address of bitmap which has nothing to do
with IOTLB. So it needs to be validated unconditionally otherwise we
may try use 0 as log_base which may lead to pin pages that will lead
unexpected result (e.g trigger BUG_ON() in set_bit_to_user()).
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API") Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase representor netdev RQ size to avoid dropped packets.
The current size (two) is just too small to keep up with
conventional slow path traffic patterns.
Also match the SQ size to the RQ size.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Global pause and PFC configuration should be mutually exclusive (i.e. only
one of them at most can be set). However, once PFC was turned off,
driver automatically turned Global pause on. This is a bug.
Fix the driver behaviour to turn off PFC/Global once the user turned the
other on.
This also fixed a weird behaviour that at a current time, the profile
had both PFC and global pause configuration turned on, which is
Hardware-wise impossible and caused returning false positive indication
to query tools.
In addition, fix error code when setting global pause or PFC to change
metadata only upon successful change.
Also, removed useless debug print.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strp_parser_err is called with a negative code everywhere, which then
calls abort_parser with a negative code. strp_msg_timeout calls
abort_parser directly with a positive code. Negate ETIMEDOUT
to match signed-ness of other calls.
The default abort_parser callback, strp_abort_strp, sets
sk->sk_err to err. Also negate the error here so sk_err always
holds a positive value, as the rest of the net code expects. Currently
a negative sk_err can result in endless loops, or user code that
thinks it actually sent/received err bytes.
Found while testing net/tls_sw recv path.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Signed-off-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
# tc action replace action skbmod swap mac index 100
is run for the first time, and tcf_skbmod_init() fails to allocate struct
tcf_skbmod_params, tcf_skbmod_cleanup() calls kfree_rcu(NULL), thus
causing the following error:
is run for the first time, and tunnel_key_init() fails to allocate struct
tcf_tunnel_key_params, tunnel_key_release() dereferences NULL pointers.
This causes the following error:
When mlx5_core is loaded it is expected to sync ports
with all vxlan devices so it can support vxlan encap/decap.
This is done via udp_tunnel_get_rx_info(). Currently this
call is set in mlx5e_nic_enable() and if the netdev is not in
NETREG_REGISTERED state it will not be called.
Normally on load the netdev state is not NETREG_REGISTERED
so udp_tunnel_get_rx_info() will not be called.
Moving udp_tunnel_get_rx_info() to mlx5e_open() so
it will be called on netdev UP event and allow encap/decap.
Fixes: 610e89e05c3f ("net/mlx5e: Don't sync netdev state when not registered") Signed-off-by: Shahar Klein <shahark@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianbo Liu [Fri, 2 Mar 2018 02:09:08 +0000 (02:09 +0000)]
net/mlx5e: Don't override vport admin link state in switchdev mode
The vport admin original link state will be re-applied after returning
back to legacy mode, it is not right to change the admin link state value
when in switchdev mode.
Use direct vport commands to alter logical vport state in netdev
representor open/close flows rather than the administrative eswitch API.
Fixes: 20a1ea674783 ('net/mlx5e: Support VF vport link state control for SRIOV switchdev mode') Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling TSO can lead to abysmal performances when using seg6 in
encap mode, such as with the ixgbe driver. This patch adds a call to
iptunnel_handle_offloads() to remove the encapsulation bit if needed.
Before:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[ 4] local fc45::4 port 36592 connected to fc00::55 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 196 KBytes 1.60 Mbits/sec 47 6.66 KBytes
[ 4] 1.00-2.00 sec 304 KBytes 2.49 Mbits/sec 100 5.33 KBytes
[ 4] 2.00-3.00 sec 284 KBytes 2.32 Mbits/sec 92 5.33 KBytes
After:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[ 4] local fc45::4 port 43062 connected to fc00::55 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 1.03 GBytes 8.89 Gbits/sec 0 743 KBytes
[ 4] 1.00-2.00 sec 1.03 GBytes 8.87 Gbits/sec 0 743 KBytes
[ 4] 2.00-3.00 sec 1.03 GBytes 8.87 Gbits/sec 0 743 KBytes
Reported-by: Tom Herbert <tom@quantonium.net> Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NSP default buffer is a piece of NFP memory where additional
command data can be placed. Its format has been copied from
host buffer, but the PCIe selection bits do not make sense in
this case. If those get masked out from a NFP address - writes
to random place in the chip memory may be issued and crash the
device.
Even in the general NSP buffer case, it doesn't make sense to have the
PCIe selection bits there anymore. These are unused at the moment, and
when it becomes necessary, the PCIe selection bits should rather be
moved to another register to utilise more bits for the buffer address.
This has never been an issue because the buffer used to be
allocated in memory with less-than-38-bit-long address but that
is about to change.
Fixes: 1a64821c6af7 ("nfp: add support for service processor access") Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
# tc action add action sample rate 100 group 100 index 100
is run for the first time, and psample_group_get(100) fails to create a
new group, tcf_sample_cleanup() calls psample_group_put(NULL), thus
causing the following error:
For NIC flows, the parsed attributes are not freed when we exit
successfully from mlx5e_configure_flower().
There is possible double free for eswitch flows. If error is returned
from rhashtable_insert_fast(), the parse attrs will be freed in
mlx5e_tc_del_flow(), but they will be freed again before exiting
mlx5e_configure_flower().
To fix both issues we do the following:
(1) change the condition that determines if to issue the free call to
check if this flow is NIC flow, or it does not have encap action.
(2) reorder the code such that that the check and free calls are done
before we attempt to add into the hash table.
Fixes: 232c001398ae ('net/mlx5e: Add support to neighbour update flow') Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we use the global ipv6_stub var to access the ipv6 global
nd table. This practice gets us to troubles when the stub is only partially
set e.g when ipv6 is loaded under the disabled policy. In this case, as of commit 343d60aada5a ("ipv6: change ipv6_stub_impl.ipv6_dst_lookup to take net argument")
the stub is not null, but stub->nd_tbl is and we crash.
As we can access the ipv6 nd_tbl directly, the fix is just to avoid the
reference through the stub. There is one place in the code where we
issue ipv6 route lookup and keep doing it through the stub, but that
mentioned commit makes sure we get -EAFNOSUPPORT from the stack.
Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow") Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Aviv Heller <avivh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is run for the first time, and tcf_vlan_init() fails allocating struct
tcf_vlan_params, tcf_vlan_cleanup() calls kfree_rcu(NULL, ...). This causes
the following error:
When we delete a u32 key via u32_delete_key(), we forget to
call idr_remove() to remove its handle from IDR.
Fixes: e7614370d6f0 ("net_sched: use idr to allocate u32 filter handles") Reported-by: Marcin Kabiesz <admin@hostcenter.eu> Tested-by: Marcin Kabiesz <admin@hostcenter.eu> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default TX moderation mode was mistakenly set to CQE based. The
intention was to add a control ability in order to improve some specific
use-cases. In general, we prefer to use EQE based moderation as it gives
much better numbers for the common cases.
CQE based causes a degradation in the common case since it resets the
moderation timer on CQE generation. This causes an issue when TSO is
well utilized (large TSO sessions). The timer is set to 16us so traffic
of ~64KB TSO sessions per second would mean timer reset (CQE per TSO
session -> long time between CQEs). In this case we quickly reach the
tcp_limit_output_bytes (256KB by default) and cause a halt in TX traffic.
By setting EQE based moderation we make sure timer would expire after
16us regardless of the packet rate.
This fixes an up to 40% packet rate and up to 23% bandwidth degradtions.
Fixes: 0088cbbc4b66 ("net/mlx5e: Enable CQE based moderation on TX CQ") Signed-off-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ip6gre_tunnel_locate+0x334/0x860 net/ipv6/ip6_gre.c:339
Write of size 20 at addr ffff8801afb9f7b8 by task syzkaller851048/4466
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ipip6_tunnel_locate+0x63b/0xaa0 net/ipv6/sit.c:254
Write of size 33 at addr ffff8801b64076d8 by task syzkaller932654/4453
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_tunnel_create+0xca/0x6b0 net/ipv4/ip_tunnel.c:257
Write of size 20 at addr ffff8801ac79f810 by task syzkaller268107/4482
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to use dev_valid_name() to validate tunnel names,
so better use strnlen(name, IFNAMSIZ) than strlen(name) to make
sure to not upset KASAN.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dev_set_promiscuity(1) succeeds but dev_set_allmulti(1) fails,
dev_set_promiscuity(-1) should be done before going to the err path.
Otherwise, dev->promiscuity will leak.
Fixes: 7e1a1ac1fbaa ("bonding: Check return of dev_set_promiscuity/allmulti") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is actually a dead lock caused by sync slave hwaddr from master when
the master is the slave's 'slave'. This dead loop check is actually done
by netdev_master_upper_dev_link. However, Commit 1f718f0f4f97 ("bonding:
populate neighbour's private on enslave") moved it after dev_mc_sync.
This patch is to fix it by moving dev_mc_sync after master_upper_dev_link,
so that this loop check would be earlier than dev_mc_sync. It also moves
if (mode == BOND_MODE_8023AD) into if (!bond_uses_primary) clause as an
improvement.
Note team driver also has this issue, I will fix it in another patch.
Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave") Reported-by: Beniamino Galvani <bgalvani@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vlan_vids_add_by_dev is called right after dev hwaddr sync, so on
the err path it should unsync dev hwaddr. Otherwise, the slave
dev's hwaddr will never be unsync when this err happens.
Fixes: 1ff412ad7714 ("bonding: change the bond's vlan syncing functions with the standard ones") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miguel reported an skb use after free / double free in vrf_finish_output
when neigh_output returns an error. The vrf driver should return after
the call to neigh_output as it takes over the skb on error path as well.
Patch is a simplified version of Miguel's patch which was written for 4.9,
and updated to top of tree.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device") Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like function ethtool_get_ts_info(), we should also consider the
phy_driver ts_info call back. For example, driver dp83640.
Fixes: 37dd9255b2f6 ("vlan: Pass ethtool get_ts_info queries to real device.") Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We tried to remove vq poll from wait queue, but do not check whether
or not it was in a list before. This will lead double free. Fixing
this by switching to use vhost_poll_stop() which zeros poll->wqh after
removing poll from waitqueue to make sure it won't be freed twice.
Cc: Darren Kenny <darren.kenny@oracle.com> Reported-by: syzbot+c0272972b01b872e604a@syzkaller.appspotmail.com Fixes: 2b8b328b61c79 ("vhost_net: handle polling errors when setting backend") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----address@SYSC_bind
Variable was created at:
SYSC_bind+0x6f/0x4b0 net/socket.c:1461
SyS_bind+0x54/0x80 net/socket.c:1460
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----addr@___sys_recvmsg
Variable was created at:
___sys_recvmsg+0xd5/0x810 net/socket.c:2172
__sys_recvmmsg+0x54e/0xdb0 net/socket.c:2313
Bytes 8-15 of 16 are uninitialized
==================================================================
Kernel panic - not syncing: panic_on_warn set ...
pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.
Fix this by calling pci_set_drvdata() before registering the
net_device.
This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.
The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once dst has been cached in socket via sk_setup_caps(),
it is illegal to call ip_rt_put() (or dst_release()),
since sk_setup_caps() did not change dst refcount.
We can still dereference it since we hold socket lock.
Caugth by syzbot :
BUG: KASAN: use-after-free in atomic_dec_return include/asm-generic/atomic-instrumented.h:198 [inline]
BUG: KASAN: use-after-free in dst_release+0x27/0xa0 net/core/dst.c:185
Write of size 4 at addr ffff8801c54dc040 by task syz-executor4/20088
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when tcf_bpf_init_from_ops() fails (e.g. because of program having invalid
number of instructions), tcf_bpf_cfg_cleanup() calls bpf_prog_put(NULL) or
bpf_prog_destroy(NULL). Unless CONFIG_BPF_SYSCALL is unset, this causes
the following error:
Fix it in tcf_bpf_cfg_cleanup(), ensuring that bpf_prog_{put,destroy}(f)
is called only when f is not NULL.
Fixes: bbc09e7842a5 ("net/sched: fix idr leak on the error path of tcf_bpf_init()") Reported-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a bug in the tcf_dump_walker function that can cause some actions
to not be reported when dumping a large number of actions. This issue
became more aggrevated when cookies feature was added. In particular
this issue is manifest when large cookie values are assigned to the
actions and when enough actions are created that the resulting table
must be dumped in multiple batches.
The number of actions returned in each batch is limited by the total
number of actions and the memory buffer size. With small cookies
the numeric limit is reached before the buffer size limit, which avoids
the code path triggering this bug. When large cookies are used buffer
fills before the numeric limit, and the erroneous code path is hit.
For example after creating 32 csum actions with the cookie aaaabbbbccccdddd
$ tc actions ls action csum
total acts 26
action order 0: csum (tcp) action continue
index 1 ref 1 bind 0
cookie aaaabbbbccccdddd
.....
action order 25: csum (tcp) action continue
index 26 ref 1 bind 0
cookie aaaabbbbccccdddd
total acts 6
action order 0: csum (tcp) action continue
index 28 ref 1 bind 0
cookie aaaabbbbccccdddd
......
action order 5: csum (tcp) action continue
index 32 ref 1 bind 0
cookie aaaabbbbccccdddd
Note that the action with index 27 is omitted from the report.
Fixes: 4b3550ef530c ("[NET_SCHED]: Use nla_nest_start/nla_nest_end")" Signed-off-by: Craig Dillabaugh <cdillaba@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx5 modify cq limits the coalescing time parameter to 12 bit
and coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
KMSAN reports use of uninitialized memory in the case when |alen| is
smaller than sizeof(struct sockaddr_nl), and therefore |nladdr| isn't
fully copied from the userspace.
Signed-off-by: Alexander Potapenko <glider@google.com> Fixes: 1da177e4c3f41524 ("Linux-2.6.12-rc2") Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of ip6_forward(), IPSTATS_MIB_OUTFORWDATAGRAMS and
IPSTATS_MIB_OUTOCTETS are incremented immediately before the NF_HOOK call
for NFPROTO_IPV6 / NF_INET_FORWARD. As a result, these counters get
incremented regardless of whether or not the netfilter hook allows the
packet to continue being processed. This change increments the counters
in ip6_forward_finish() so that it will not happen if the netfilter hook
chooses to terminate the packet, which is similar to how IPv4 works.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Donald reported that IPv6 route leaking between VRFs is not working.
The root cause is the strict argument in the call to rt6_lookup when
validating the nexthop spec.
ip6_route_check_nh validates the gateway and device (if given) of a
route spec. It in turn could call rt6_lookup (e.g., lookup in a given
table did not succeed so it falls back to a full lookup) and if so
sets the strict argument to 1. That means if the egress device is given,
the route lookup needs to return a result with the same device. This
strict requirement does not work with VRFs (IPv4 or IPv6) because the
oif in the flow struct is overridden with the index of the VRF device
to trigger a match on the l3mdev rule and force the lookup to its table.
The right long term solution is to add an l3mdev index to the flow
struct such that the oif is not overridden. That solution will not
backport well, so this patch aims for a simpler solution to relax the
strict argument if the route spec device is an l3mdev slave. As done
in other places, use the FLOWI_FLAG_SKIP_NH_OIF to know that the
RT6_LOOKUP_F_IFACE flag needs to be removed.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack") Reported-by: Donald Sharp <sharpd@cumulusnetworks.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb mac header is not necessarily set at the time skb_network_protocol()
is called. Use skb->data instead.
BUG: KASAN: slab-out-of-bounds in skb_network_protocol+0x46b/0x4b0 net/core/dev.c:2739
Read of size 2 at addr ffff8801b3097a0b by task syz-executor5/14242
Fixes: 19acc327258a ("gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pravin B Shelar <pshelar@ovn.org> Reported-by: Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com> Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.
Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.
Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While building ipv6 datagram we currently allow arbitrary large
extheaders, even beyond pmtu size. The syzbot has found a way
to exploit the above to trigger the following splat:
When a host fragments an IPv6 datagram, it MUST include the entire
IPv6 Header Chain in the First Fragment.
So this patch addresses the issue dropping datagrams with excessive
extheader length. It also updates the error path to report to the
calling socket nonnegative pmtu values.
The issue apparently predates git history.
v1 -> v2: cleanup error path, as per Eric's suggestion
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+91e6f9932ff122fa4410@syzkaller.appspotmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arp_filter performs an ip_route_output search for arp source address and
checks if output device is the same where the arp request was received,
if it is not, the arp request is not answered.
This route lookup is always done on main route table so l3slave devices
never find the proper route and arp is not answered.
Passing l3mdev_master_ifindex_rcu(dev) return value as oif fixes the
lookup for l3slave devices while maintaining same behavior for non
l3slave devices as this function returns 0 in that case.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:
microcode: microcode_reload_late: late_cpus: 4
microcode: __reload_late: cpu 2 entered
microcode: __reload_late: cpu 1 entered
microcode: __reload_late: cpu 3 entered
microcode: __reload_late: cpu 0 entered
microcode: __reload_late: cpu 1 left
microcode: Timeout while waiting for CPUs rendezvous, remaining: 1
CPU1 above would finish, leave and the others will still spin waiting for
it to join.
So do two synchronization atomics instead, which makes the code a lot more
straightforward.
Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.
That's ok because the moment all CPUs are done, that timeout will be cut
short.
Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.
Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
Original idea by Ashok, completely rewritten by Borislav.
Before you read any further: the early loading method is still the
preferred one and you should always do that. The following patch is
improving the late loading mechanism for long running jobs and cloud use
cases.
Gather all cores and serialize the microcode update on them by doing it
one-by-one to make the late update process as reliable as possible and
avoid potential issues caused by the microcode update.
[ Borislav: Rewrite completely. ]
Co-developed-by: Borislav Petkov <bp@suse.de> Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-8-bp@alien8.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... so that any newer version can land in the cache and can later be
fished out by the application functions. Do that before grabbing the
hotplug lock.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-7-bp@alien8.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid loading microcode if any of the CPUs are offline, and issue a
warning. Having different microcode revisions on the system at any time
is outright dangerous.
Updating microcode is less error prone when caches have been flushed and
depending on what exactly the microcode is updating. For example, some
of the issues around certain Broadwell parts can be addressed by doing a
full cache flush.
[ Borislav: Massage it and use native_wbinvd() in both cases. ]
After updating microcode on one of the threads of a core, the other
thread sibling automatically gets the update since the microcode
resources on a hyperthreaded core are shared between the two threads.
Check the microcode revision on the CPU before performing a microcode
update and thus save us the WRMSR 0x79 because it is a particularly
expensive operation.
With some microcode upgrades, new CPUID features can become visible on
the CPU. Check what the kernel has mirrored now and issue a warning
hinting at possible things the user/admin can do to make use of the
newly visible features.
Originally-by: Ashok Raj <ashok.raj@intel.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180216112640.11554-4-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a callback function which the microcode loader calls when microcode
has been updated to a newer revision. Do the callback only when no error
was encountered during loading.
Tested-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180216112640.11554-3-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the table result is out of bounds on the array map
there is something really wrong with VBT pin so we don't
return that vbt_pin, but only return 0 instead.
This basically reverts commit 'a8e6f3888b05 ("drm/i915/cnp:
Ignore VBT request for know invalid DDC pin.")'
Also this properly fixes commit 9c3b2689d01f ("drm/i915/cnl:
Map VBT DDC Pin to BSpec DDC Pin.")
v2: Do in a way that we don't break other platforms. (Jani)
v3: Keep debug message (Jani)
v4: Don't mess with 0 mapping was noticed by Jani and
addressed with a simple solution suggested by Lucas
that makes this even simpler.
Fixes: a8e6f3888b05 ("drm/i915/cnp: Ignore VBT request for know invalid DDC pin.") Fixes: 9c3b2689d01f ("drm/i915/cnl: Map VBT DDC Pin to BSpec DDC Pin.") Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Kai Heng Feng <kai.heng.feng@canonical.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180125222524.22059-1-rodrigo.vivi@intel.com
(cherry picked from commit 3393ce1ed8fc43dbdb83952facaf04e644ca1d54) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we cannot setup a cmd because we run out of ring space
or global pages release the blocks before sleeping. This
prevents a deadlock where dev0 has waiting_blocks set and
needs N blocks, but dev1 to devX have each allocated N / X blocks
and also hit the global block limit so they went to sleep.
find_free_blocks is not able to take the sleeping dev's
blocks becaause their waiting_blocks is set and even
if it was not the block returned by find_last_bit could equal
dbi_max. The latter will probably never happen because
DATA_BLOCK_BITS is so high but in the next patches
DATA_BLOCK_BITS and TCMU_GLOBAL_MAX_BLOCKS will be settable so
it might be lower and could happen.
Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to increase output offset in each iteration, not decrease it as
we currently do.
I guess we were lucky to finish in most cases in first iteration, so the
bug never showed. However it shows a lot when working with big (~4GB)
size data.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 9c9f5a2f1944 ("perf tools: Introduce copyfile_offset() function") Link: http://lkml.kernel.org/r/20180109133923.25406-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing other changes, I discovered that gcc-7.2.1 produces badly
optimized code for aes_encrypt/aes_decrypt. This is especially true when
CONFIG_UBSAN_SANITIZE_ALL is enabled, where it leads to extremely
large stack usage that in turn might cause kernel stack overflows:
crypto/aes_generic.c: In function 'aes_encrypt':
crypto/aes_generic.c:1371:1: warning: the frame size of 4880 bytes is larger than 2048 bytes [-Wframe-larger-than=]
crypto/aes_generic.c: In function 'aes_decrypt':
crypto/aes_generic.c:1441:1: warning: the frame size of 4864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
I verified that this problem exists on all architectures that are
supported by gcc-7.2, though arm64 in particular is less affected than
the others. I also found that gcc-7.1 and gcc-8 do not show the extreme
stack usage but still produce worse code than earlier versions for this
file, apparently because of optimization passes that generally provide
a substantial improvement in object code quality but understandably fail
to find any shortcuts in the AES algorithm.
Possible workarounds include
a) disabling -ftree-pre and -ftree-sra optimizations, this was an earlier
patch I tried, which reliably fixed the stack usage, but caused a
serious performance regression in some versions, as later testing
found.
b) disabling UBSAN on this file or all ciphers, as suggested by Ard
Biesheuvel. This would lead to massively better crypto performance in
UBSAN-enabled kernels and avoid the stack usage, but there is a concern
over whether we should exclude arbitrary files from UBSAN at all.
c) Forcing the optimization level in a different way. Similar to a),
but rather than deselecting specific optimization stages,
this now uses "gcc -Os" for this file, regardless of the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE/SIZE option. This is a reliable
workaround for the stack consumption on all architecture, and I've
retested the performance results now on x86, cycles/byte (lower is
better) for cbc(aes-generic) with 256 bit keys:
This implements the option c) by enabling forcing -Os on all compiler
versions starting with gcc-7.1. As a workaround for PR83356, it would
only be needed for gcc-7.2+ with UBSAN enabled, but since it also shows
better performance on gcc-7.1 without UBSAN, it seems appropriate to
use the faster version here as well.
Side note: during testing, I also played with the AES code in libressl,
which had a similar performance regression from gcc-6 to gcc-7.2,
but was three times slower overall. It might be interesting to
investigate that further and possibly port the Linux implementation
into that.
Reads from NAND devices usually trigger bitflips, this is an expected
behavior. While bitflips are under a given threshold, the MTD core
returns 0. However, when the number of corrected bitflips is above this
same threshold, -EUCLEAN is returned to inform the upper layer that this
block is slightly dying and soon the ECC engine will be overtaken so
actions should be taken to move the data out of it.
This particular condition should not be treated like an error and the
test should continue.
We should not try to do any i2c transfers before the controller is
resumed (which happens before our resume method gets called).
So we need to disable our IRQ while suspended to enforce this. The
code paths for devices with GPIOs for the int and reset pins already
disable the IRQ the through goodix_free_irq().
This commit also disables the IRQ while suspended for devices without
GPIOs for the int and reset pins.
This fixes the i2c bus sometimes getting stuck after a suspend/resume
causing the touchscreen to sometimes not work after a suspend/resume.
This has been tested on a GPD pocked device.
Initiating a kdump via the command line can cause a pending interrupt
to be handled by the ibmvnic driver when initializing the sub-CRQ
irqs during driver initialization.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Edison the Broadcom Wi-Fi card, which is connected to SDIO,
requires 2.0v, while the host, according to Intel Merrifield TRM,
supports 1.8v supply only.
The card announces itself as
mmc2: new ultra high speed DDR50 SDIO card at address 0001
Introduce a custom OCR mask for SDIO host controller on Intel Merrifield
and add a special case to sdhci_set_power_noreg() to override 2.0v supply
by enforcing 1.8v power choice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On machines where the GART aperture is mapped over physical RAM
/proc/vmcore contains the remapped range and reading it may cause hangs or
reboots.
In the past, the GART region was added into the resource map, implemented
by commit 56dd669a138c ("[PATCH] Insert GART region into resource map")
However, inserting the iomem_resource from the early GART code caused
resource conflicts with some AGP drivers (bko#72201), which got avoided by
reverting the patch in commit 707d4eefbdb3 ("Revert [PATCH] Insert GART
region into resource map"). This revert introduced the /proc/vmcore bug.
The vmcore ELF header is either prepared by the kernel (when using the
kexec_file_load syscall) or by the kexec userspace (when using the kexec_load
syscall). Since we no longer have the GART iomem resource, the userspace
kexec has no way of knowing which region to exclude from the ELF header.
Changes from v1 of this patch:
Instead of excluding the aperture from the ELF header, this patch
makes /proc/vmcore return zeroes in the second kernel when attempting to
read the aperture region. This is done by reusing the
gart_oldmem_pfn_is_ram infrastructure originally intended to exclude XEN
balooned memory. This works for both, the kexec_file_load and kexec_load
syscalls.
[Note that the GART region is the same in the first and second kernels:
regardless whether the first kernel fixed up the northbridge/bios setting
and mapped the aperture over physical memory, the second kernel finds the
northbridge properly configured by the first kernel and the aperture
never overlaps with e820 memory because the second kernel has a fake e820
map created from the crashkernel memory regions. Thus, the second kernel
keeps the aperture address/size as configured by the first kernel.]
register_oldmem_pfn_is_ram can only register one callback and returns an error
if the callback has been registered already. Since XEN used to be the only user
of this function, it never checks the return value. Now that we have more than
one user, I added a WARN_ON just in case agp, XEN, or any other future user of
register_oldmem_pfn_is_ram were to step on each other's toes.
Fixes: 707d4eefbdb3 ("Revert [PATCH] Insert GART region into resource map") Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Baoquan He <bhe@redhat.com> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: David Airlie <airlied@linux.ie> Cc: yinghai@kernel.org Cc: joro@8bytes.org Cc: kexec@lists.infradead.org Cc: Borislav Petkov <bp@alien8.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Dave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Link: https://lkml.kernel.org/r/20180106010013.73suskgxm7lox7g6@dwarf.suse.cz Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'if' logic in ucma_query_path was broken with OPA was introduced
and started to treat RoCE paths as as OPA paths. Invert the logic
of the 'if' so only OPA paths are treated as OPA paths.
Otherwise the path records returned to rdma_cma users are mangled
when in RoCE mode.
Fixes: 57520751445b ("IB/SA: Add OPA path record type") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue - Driver returns DID_NO_CONNECT when unload is in progress,
indicated using instance->unload flag. In case of dynamic unload of
driver, this flag is set before calling scsi_remove_host(). While doing
manual driver unload, user will see lots of prints for Sync Cache
command with DID_NO_CONNECT status.
Fix - Set the instance->unload flag after scsi_remove_host(). Allow
device removal process to be completed and do not block any command
before that. SCSI commands (like SYNC_CACHE) are received (as part of
scsi_remove_host) by driver during unload will be submitted further down
to the drives.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently driver does not validate ldcount provided by firmware. If the
value is invalid, fail RAID map validation accordingly. This issue is
rare to hit in field and is fixed as part of code review.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 10da65423fdb (PM / Domains: Call driver's noirq callbacks)
started to respect driver's noirq callbacks, but while doing that it
also introduced a few potential problems.
More precisely, in genpd_finish_suspend() and genpd_resume_noirq()
the noirq callbacks at the driver level should be invoked, no matter
of whether dev->power.wakeup_path is set or not.
Additionally, the commit in question also made genpd_resume_noirq()
to ignore the return value from pm_runtime_force_resume().
We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and
the extant logic would flag that as an error. This was already fixed in
cxgb4 driver with "92ddcc7 cxgb4: Fix some small bugs in
t4_sge_init_soft() when our Page Size is 64KB".
Original Work by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In i40evf_reset_task we use netif_running() to determine whether or not
the device is currently up. This allows us to properly free queue memory
and shut down things before we request the hardware reset.
It turns out that we cannot be guaranteed of netif_running() returning
false until the device is fully up, as the kernel core code sets
__LINK_STATE_START prior to calling .ndo_open. Since we're not holding
the rtnl_lock(), it's possible that the driver's i40evf_open handler
function is currently being called while we're resetting.
We can't simply hold the rtnl_lock() while checking netif_running() as
this could cause a deadlock with the i40evf_open() function.
Additionally, we can't avoid the deadlock by holding the rtnl_lock()
over the whole reset path, as this essentially serializes all resets,
and can cause massive delays if we have multiple VFs on a system.
Instead, lets just check our own internal state __I40EVF_RUNNING state
field. This allows us to ensure that the state is correct and is only
set after we've finished bringing the device up.
Without this change we might free data structures about device queues
and other memory before they've been fully allocated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51a1 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.
Fixes: 3e81a4ca51a1 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->close, ->suspend and ->resume hooks assume presence of a valid IRQ
if the device is wakeup capable. However it's entirely possible that
wakeup was enabled by some other entity besides this driver and in this
case the user will get a WARN splat if no valid IRQ was found. Avoid by
checking if the IRQ is valid, i.e. > 0.
Case in point: On recent MacBook Pros, the Bluetooth device lacks an
IRQ (because host wakeup is handled by the SMC, independently of the
operating system), but it does possess a _PRW method (which specifies
the SMC's GPE as wake event). The ACPI core therefore automatically
marks the physical Bluetooth device wakeup capable upon binding it to
its ACPI companion:
Commit 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices")
amended this driver to request a shutdown and device wake GPIO on probe,
but mandated that only one of them need to be present:
/* Make sure at-least one of the GPIO is defined and that
* a name is specified for this instance
*/
if ((!dev->device_wakeup && !dev->shutdown) || !dev->name) {
dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
However the same commit added a call to bcm_gpio_set_power() to the
->probe hook, which unconditionally accesses *both* GPIOs. Luckily,
the resulting NULL pointer deref was never reported, suggesting there's
no machine where either GPIO is missing.
Commit 8a92056837fd ("Bluetooth: hci_bcm: Add (runtime)pm support to the
serdev driver") removed the check whether at least one of the GPIOs is
present without specifying a reason.
Because commit 62aaefa7d038 ("Bluetooth: hci_bcm: improve use of gpios
API") refactored the driver to use devm_gpiod_get_optional() instead of
devm_gpiod_get(), one is now tempted to believe that the driver doesn't
require *any* of the two GPIOs.
Which is wrong, the driver still requires both GPIOs to avoid a NULL
pointer deref. To this end, establish the status quo ante and request
the GPIOs with devm_gpiod_get() again. Bail out of ->probe if either
of them is missing.
Oddly enough, whereas bcm_gpio_set_power() accesses the device wake pin
unconditionally, bcm_suspend_device() and bcm_resume_device() do check
for its presence before accessing it. Those checks are superfluous,
so remove them.
In order for userspace application to signal host, it needs the
host to support the monitor page property. Check for the flag
and fail if this is not supported.
ACPI enumerated serdev-controllers do not have an ACPI companion, the ACPI
companion belongs to the serdev-device child of the serdev-controller, not
to the controller itself. This was causing serdev_uevent to always return
-ENODEV when called on a serdev-controller leading to errors like these:
kernel: serial serial0: uevent: failed to send synthetic uevent
being logged. This commit modifies serdev_uevent to directly return 0
when called on an ACPI enumerated serdev-controller fixing this.
Note: I do not think that setting a modalias on a devicetree enumerated
serdev-controller makes sense either. So perhaps the !dev->of_node part of
the check can be dropped too, but I'm not entirely sure that doing this
on devicetree too is correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For each pair [device for which bfq is selected as I/O scheduler,
group in blkio/io], bfq maintains a corresponding bfq group. Each such
bfq group contains a set of async queues, with each async queue
created on demand, i.e., when some I/O request arrives for it. On
creation, an async queue gets an extra reference, to make sure that
the queue is not freed as long as its bfq group exists. Accordingly,
to allow the queue to be freed after the group exited, this extra
reference must released on group exit.
The above holds also for a bfq root group, i.e., for the bfq group
corresponding to the root blkio/io root for a given device. Yet, by
mistake, the references to the existing async queues of a root group
are not released when the latter exits. This causes a memory leak when
the instance of bfq for a given device exits. In a similar vein,
bfqg_stats_xfer_dead is not executed for a root group.
This commit fixes bfq_pd_offline so that the latter executes the above
missing operations for a root group too.
Some devices have the control dlci stay in ADM mode instead of the UA
mode. This can seen at least on droid 4 when trying to open the ts
27.010 mux port. Enabling n_gsm debug mode shows the control dlci
always respond with DM to SABM instead of UA:
Note that this is different issue from other n_gsm -EL2HLT issues such
as timeouts when the control dlci does not respond at all.
The ADM mode seems to be a quite common according to "RF Wireless World"
article "GSM Issue-UE sends SABM and gets a DM response instead of
UA response":
This issue is most commonly observed in GSM networks where in UE sends
SABM and expects network to send UA response but it ends up receiving
DM response from the network. SABM stands for Set asynchronous balanced
mode, UA stands for Unnumbered Acknowledge and DA stands for
Disconnected Mode.
An RLP entity can be in one of two modes:
- Asynchronous Balanced Mode (ABM)
- Asynchronous Disconnected Mode (ADM)
Currently Linux kernel closes the control dlci after several retries
in gsm_dlci_t1() on DM. This causes n_gsm /dev/gsmtty ports to produce
error code -EL2HLT when trying to open them as the closing of control
dlci has already set gsm->dead.
Let's fix the issue by allowing control dlci stay in ADM mode after the
retries so the /dev/gsmtty ports can be opened and used. It seems that
it might take several attempts to get any response from the control
dlci, so it's best to allow ADM mode only after the SABM retries are
done.
Note that for droid 4 additional patches are needed to mux the ttyS0
pins and to toggle RTS gpio_149 to wake up the mdm6600 modem are also
needed to use n_gsm. And the mdm6600 modem needs to be powered on.
Cc: linux-serial@vger.kernel.org Cc: Alan Cox <alan@llwyncelyn.cymru> Cc: Jiri Prchal <jiri.prchal@aksignal.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russ Gorby <russ.gorby@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW queues may be unmapped in some cases, such as blk_mq_update_nr_hw_queues(),
then we need to check it before calling blk_mq_tag_idle(), otherwise
the following kernel oops can be triggered, so fix it by checking if
the hw queue is unmapped since it doesn't make sense to idle the tags
any more after hw queues are unmapped.
The current implementation takes the child timestamp object from
the parent since the rq in mlx5i_complete_rx_cqe belongs to the parent.
This change fixes the issue by taking the correct timestamp.
Fixes: 7e7f4780c340 ("net/mlx5e: IPoIB, Use hash-table to map between QPN to child netdev") Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status of SAS PHY is in sas_phy->enabled. There is an issue that the
status of a remote SAS PHY may be initialized incorrectly: if disable
remote SAS PHY through sysfs interface (such as echo 0 >
/sys/class/sas_phy/phy-1:0:0/enable), then reboot the system, and we
will find the status of remote SAS PHY which is disabled before is
1 (cat /sys/class/sas_phy/phy-1:0:0/enable). But actually the status of
remote SAS PHY is disabled and the device attached is not found.
In SAS protocol, NEGOTIATED LOGICAL LINK RATE field of DISCOVER response
is 0x1 when remote SAS PHY is disabled. So initialize sas_phy->enabled
according to the value of NEGOTIATED LOGICAL LINK RATE field.
Signed-off-by: chenxiang <chenxiang66@hisilicon.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intend purpose here was to goto out if smp_execute_task() returned
error. Obviously something got screwed up. We will never get these link
error statistics below:
Now libsas hotplug work is static, every sas event type has its own
static work, LLDD driver queues the hotplug work into shost->work_q. If
LLDD driver burst posts lots hotplug events to libsas, the hotplug
events may pending in the workqueue like
shost->work_q
new work[PORTE_BYTES_DMAED] --> |[PHYE_LOSS_OF_SIGNAL][PORTE_BYTES_DMAED] -> processing
|<-------wait worker to process-------->|
In this case, a new PORTE_BYTES_DMAED event coming, libsas try to queue
it to shost->work_q, but this work is already pending, so it would be
lost. Finally, libsas delete the related sas port and sas devices, but
LLDD driver expect libsas add the sas port and devices(last sas event).
This patch use dynamic allocated work to avoid this issue.
Signed-off-by: Yijing Wang <wangyijing@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In such scenario that there are some flash only volumes
, and some cached devices, when many tasks request these devices in
writeback mode, the write IOs may fall to the same bucket as bellow:
| cached data | flash data | cached data | cached data| flash data|
then after writeback of these cached devices, the bucket would
be like bellow bucket:
| free | flash data | free | free | flash data |
So, there are many free space in this bucket, but since data of flash
only volumes still exists, so this bucket cannot be reclaimable,
which would cause waste of bucket space.
In this patch, we segregate flash only volume write streams from
cached devices, so data from flash only volumes and cached devices
can store in different buckets.
Compare to v1 patch, this patch do not add a additionally open bucket
list, and it is try best to segregate flash only volume write streams
from cached devices, sectors of flash only volumes may still be mixed
with dirty sectors of cached device, but the number is very small.
[mlyle: fixed commit log formatting, permissions, line endings]
Currently, when a cached device detaching from cache, writeback thread is
not stopped, and writeback_rate_update work is not canceled. For example,
after the following command:
echo 1 >/sys/block/sdb/bcache/detach
you can still see the writeback thread. Then you attach the device to the
cache again, bcache will create another writeback thread, for example,
after below command:
echo ba0fb5cd-658a-4533-9806-6ce166d883b9 > /sys/block/sdb/bcache/attach
then you will see 2 writeback threads.
This patch stops writeback thread and cancels writeback_rate_update work
when cached device detaching from cache.
Compare with patch v1, this v2 patch moves code down into the register
lock for safety in case of any future changes as Coly and Mike suggested.
The read request might meet error when searching the btree, but the error
was not handled in cache_lookup(), and this kind of metadata failure will
not go into cached_dev_read_error(), finally, the upper layer will receive
bi_status=0. In this patch we judge the metadata error by the return
value of bch_btree_map_keys(), there are two potential paths give rise to
the error:
1. Because the btree is not totally cached in memery, we maybe get error
when read btree node from cache device (see bch_btree_node_get()), the
likely errno is -EIO, -ENOMEM
2. When read miss happens, bch_btree_insert_check_key() will be called to
insert a "replace_key" to btree(see cached_dev_cache_miss(), just for
doing preparatory work before insert the missed data to cache device),
a failure can also happen in this situation, the likely errno is
-ENOMEM
bch_btree_map_keys() will return MAP_DONE in normal scenario, but we will
get either -EIO or -ENOMEM in above two cases. if this happened, we should
NOT recover data from backing device (when cache device is dirty) because
we don't know whether bkeys the read request covered are all clean. And
after that happened, s->iop.status is still its initially value(0) before
we submit s->bio.bio, we set it to BLK_STS_IOERR, so it can go into
cached_dev_read_error(), and finally it can be passed to upper layer, or
recovered by reread from backing device.
when changing MTU, The new MTU must need to be set to netdevice.
Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member "stats_offset" was designed to indicate the offset
of each member of struct ring_stats in struct hns3_enet_ring,
but forgot to add the offset of the member in struct ring_stats.
Fixes: 496d03e960a ("net: hns3: Add Ethtool support to HNS3 driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log