Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.
This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C
Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #11350 [hci0] 84680.231216
Address: 56:BC:E8:24:11:68 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #11351 [hci0] 84680.246022
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #11352 [hci0] 84680.246417
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #11353 [hci0] 84680.248854
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11354 [hci0] 84680.249466
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #11355 [hci0] 84680.253222
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #11356 [hci0] 84680.458387
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11357 [hci0] 84680.458737
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #11358 [hci0] 84680.469982
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #11359 [hci0] 84680.470444
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #11360 [hci0] 84680.474971
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4 #11362 [hci0] 84682.551014
LE Create Connection Cancel (0x08|0x000e) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #11363 [hci0] 84682.551074
LE Connection Complete (0x01)
Status: Unknown Connection Identifier (0x02)
Handle: 0
Role: Master (0x00)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Connection interval: 0.00 msec (0x0000)
Connection latency: 0 (0x0000)
Supervision timeout: 0 msec (0x0000)
Master clock accuracy: 0x00
After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #210 [hci0] 667.152459
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #211 [hci0] 667.153613
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #212 [hci0] 667.153704
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #213 [hci0] 667.154584
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #214 [hci0] 667.182619
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #215 [hci0] 667.182704
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #216 [hci0] 667.183599
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #217 [hci0] 667.183645
Address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #218 [hci0] 667.184590
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #219 [hci0] 667.184613
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #220 [hci0] 667.186558
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #221 [hci0] 667.485824
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 0
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13 {0x0002} [hci0] 667.485996
LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
Flags: 0x00000000
Data length: 0
Patch series "mm/get_user_pages_fast fixes, cleanups", v2.
Turns out get_user_pages_fast and __get_user_pages_fast return different
values on error when given a single page: __get_user_pages_fast returns
0. get_user_pages_fast returns either 0 or an error.
Callers of get_user_pages_fast expect an error so fix it up to return an
error consistently.
Stress the difference between get_user_pages_fast and
__get_user_pages_fast to make sure callers aren't confused.
This patch (of 3):
__gup_benchmark_ioctl does not handle the case where get_user_pages_fast
fails:
- a negative return code will cause a buffer overrun
- returning with partial success will cause use of uninitialized
memory.
[akpm@linux-foundation.org: simplification] Link: http://lkml.kernel.org/r/1522962072-182137-3-git-send-email-mst@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_user_pages_fast is supposed to be a faster drop-in equivalent of
get_user_pages. As such, callers expect it to return a negative return
code when passed an invalid address, and never expect it to return 0
when passed a positive number of pages, since its documentation says:
* Returns number of pages pinned. This may be fewer than the number
* requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno.
When get_user_pages_fast fall back on get_user_pages this is exactly
what happens. Unfortunately the implementation is inconsistent: it
returns 0 if passed a kernel address, confusing callers: for example,
the following is pretty common but does not appear to do the right thing
with a kernel address:
ret = get_user_pages_fast(addr, 1, writeable, &page);
if (ret < 0)
return ret;
Change get_user_pages_fast to return -EFAULT when supplied a kernel
address to make it match expectations.
All callers have been audited for consistency with the documented
semantics.
Link: http://lkml.kernel.org/r/1522962072-182137-4-git-send-email-mst@redhat.com Fixes: 5b65c4677a57 ("mm, x86/mm: Fix performance regression in get_user_pages_fast()") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Git commit c60a03fee0e5 ("s390: switch to {get,put}_compat_sigset()")
contains a typo and now copies the wrong pointer to user space.
Use the correct pointer instead.
Reported-and-tested-by: Stefan Liebler <stli@linux.vnet.ibm.com> Fixes: c60a03fee0e5 ("s390: switch to {get,put}_compat_sigset()") Cc: <stable@vger.kernel.org> # v4.15+ Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On an Output queue, both EMPTY and PENDING buffer states imply that the
buffer is ready for completion-processing by the upper-layer drivers.
So for a non-QEBSM Output queue, get_buf_states() merges mixed
batches of PENDING and EMPTY buffers into one large batch of EMPTY
buffers. The upper-layer driver (ie. qeth) later distuingishes PENDING
from EMPTY by inspecting the slsb_state for
QDIO_OUTBUF_STATE_FLAG_PENDING.
But the merge logic in get_buf_states() contains a bug that causes us to
erronously also merge ERROR buffers into such a batch of EMPTY buffers
(ERROR is 0xaf, EMPTY is 0xa1; so ERROR & EMPTY == EMPTY).
Effectively, most outbound ERROR buffers are currently discarded
silently and processed as if they had succeeded.
Note that this affects _all_ non-QEBSM device types, not just IQD with CQ.
Fix it by explicitly spelling out the exact conditions for merging.
For extracting the "get initial state" part out of the loop, this relies
on the fact that get_buf_states() is never called with a count of 0. The
QEBSM path already strictly requires this, and the two callers with
variable 'count' make sure of it.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Cc: <stable@vger.kernel.org> #v3.2+ Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate retry of EQBS after CCQ 96 means that we potentially misreport
the state of buffers inspected during the first EQBS call.
This occurs when
1. the first EQBS finds all inspected buffers still in the initial state
set by the driver (ie INPUT EMPTY or OUTPUT PRIMED),
2. the EQBS terminates early with CCQ 96, and
3. by the time that the second EQBS comes around, the state of those
previously inspected buffers has changed.
If the state reported by the second EQBS is 'driver-owned', all we know
is that the previous buffers are driver-owned now as well. But we can't
tell if they all have the same state. So for instance
- the second EQBS reports OUTPUT EMPTY, but any number of the previous
buffers could be OUTPUT ERROR by now,
- the second EQBS reports OUTPUT ERROR, but any number of the previous
buffers could be OUTPUT EMPTY by now.
Effectively, this can result in both over- and underreporting of errors.
If the state reported by the second EQBS is 'HW-owned', that doesn't
guarantee that the previous buffers have not been switched to
driver-owned in the mean time. So for instance
- the second EQBS reports INPUT EMPTY, but any number of the previous
buffers could be INPUT PRIMED (or INPUT ERROR) by now.
This would result in failure to process pending work on the queue. If
it's the final check before yielding initiative, this can cause
a (temporary) queue stall due to IRQ avoidance.
Fixes: 25f269f17316 ("[S390] qdio: EQBS retry after CCQ 96") Cc: <stable@vger.kernel.org> #v3.2+ Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf03c00e7c1 "nfit: scrub and register regions in a workqueue"
mistakenly attempts to register a region per BLK aperture. There is
nothing to register for individual apertures as they belong as a set to
a BLK aperture group that are registered with a corresponding
DIMM-control-region. Filter them for registration to prevent some
needless devm_kzalloc() allocations.
Cc: <stable@vger.kernel.org> Fixes: 1cf03c00e7c1 ("nfit: scrub and register regions in a workqueue") Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ 92.931922] 1 lock held by systemd-udevd/525:
[ 92.933642] #0: 00000000a2849e25 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x73/0x4f0
----------------------------------------
The reason of deadlock turned out that wait_event_interruptible() in
blk_queue_enter() got stuck with bdev->bd_mutex held at __blkdev_put()
due to q->mq_freeze_depth == 1.
[ 92.943530] 1 lock held by a.out/634:
[ 92.945105] #0: 00000000a2849e25 (&bdev->bd_mutex){+.+.}, at: __blkdev_put+0x3c/0x1e0
----------------------------------------
The reason of q->mq_freeze_depth == 1 turned out that loop_set_status()
forgot to call blk_mq_unfreeze_queue() at error paths for
info->lo_encrypt_type != NULL case.
Resource auditing is using the peer field which is not available
when the rlim data struct is used, because it is a different element
of the same union. Accessing peer during resource auditing could
cause garbage log entries or even oops the kernel.
Move the rlim data block into the same struct as the peer field
so they can be used together.
CC: <stable@vger.kernel.org> Fixes: 86b92cb782b3 ("apparmor: move resource checks to using labels") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .ns_name should not be virtualized by the current ns view. It
needs to report the ns base name as that is being used during startup
as part of determining apparmor policy namespace support.
The existence test is not being properly logged as the signal mapping
maps it to the last entry in the named signal table. This is done
to help catch bugs by making the 0 mapped signal value invalid so
that we can catch the signal value not being filled in.
When fixing the off-by-one comparision logic the reporting of the
existence test was broken, because the logic behind the mapped named
table was hidden. Fix this by adding a define for the name lookup
and using it.
Cc: Stable <stable@vger.kernel.org> Fixes: f7dc4c9a855a1 ("apparmor: fix off-by-one comparison on MAXMAPPED_SIG") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that fixes the crashes in the following commit introduced a small
memory leak:
commit 6a2cf8d3663e ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Fixing this requires a bit of reworking, which I've explained. Also provide
some code cleanup.
There is a small window in qla2x00_probe_one where if qla2x00_alloc_queues
fails, we end up never freeing req and rsp and leak 0xc0 and 0xc8 bytes
respectively (the sizes of req and rsp).
I originally put in checks to test for this condition which were based on
the incorrect assumption that if ha->rsp_q_map and ha->req_q_map were
allocated, then rsp and req were allocated as well. This is incorrect.
There is a window between these allocations:
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
goto probe_hw_failed;
ret = qla2x00_request_irqs(ha, rsp);
goto probe_failed;
if (qla2x00_alloc_queues(ha, req, rsp)) {
goto probe_failed;
[if successful, now ha->rsp_q_map and ha->req_q_map allocated]
To simplify this, we should just set req and rsp to NULL after we free
them. Sounds simple enough? The problem is that req and rsp are pointers
defined in the qla2x00_probe_one and they are not always passed by reference
to the routines that free them.
Here are paths which can free req and rsp:
PATH 1:
qla2x00_probe_one
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
[req and rsp are passed by reference, but if this fails, we currently
do not NULL out req and rsp. Easily fixed]
PATH 2:
qla2x00_probe_one
failing in qla2x00_request_irqs or qla2x00_alloc_queues
probe_failed:
qla2x00_free_device(base_vha);
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 3:
qla2x00_probe_one:
failing in qla2x00_mem_alloc or qla2x00_create_host
probe_hw_failed:
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 1: This should currently work, but it doesn't because rsp and rsp are
not set to NULL in qla2x00_mem_alloc. Easily remedied.
PATH 2: req and rsp aren't passed in at all to qla2x00_free_device but are
derived from ha->req_q_map[0] and ha->rsp_q_map[0]. These are only set up if
qla2x00_alloc_queues succeeds.
In qla2x00_free_queues, we are protected from crashing if these don't exist
because req_qid_map and rsp_qid_map are only set on their allocation. We are
guarded in this way:
for (cnt = 0; cnt < ha->max_req_queues; cnt++) {
if (!test_bit(cnt, ha->req_qid_map))
continue;
PATH 3: This works. We haven't freed req or rsp yet (or they were never
allocated if qla2x00_mem_alloc failed), so we'll attempt to free them here.
To summarize, there are a few small changes to make this work correctly and
(and for some cleanup):
1) (For PATH 1) Set *rsp and *req to NULL in case of failure in
qla2x00_mem_alloc so these are correctly set to NULL back in
qla2x00_probe_one
2) After jumping to probe_failed: and calling qla2x00_free_device,
explicitly set rsp and req to NULL so further calls with these pointers do
not crash, i.e. the free queue calls in the probe_hw_failed section we fall
through to.
3) Fix return code check in the call to qla2x00_alloc_queues. We currently
drop the return code on the floor. The probe fails but the caller of the
probe doesn't have an error code, so it attaches to pci. This can result in
a crash on module shutdown.
4) Remove unnecessary NULL checks in qla2x00_free_req_que,
qla2x00_free_rsp_que, and the egregious NULL checks before kfrees and vfrees
in qla2x00_mem_free.
I tested this out running a scenario where the card breaks at various times
during initialization. I made sure I forced every error exit path in
qla2x00_probe_one.
Cc: <stable@vger.kernel.org> # v4.16 Fixes: 6a2cf8d3663e ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure") Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're neglecting to clear the umask after it's set, which can cause a
later unrelated rpc to (incorrectly) use the same umask if it happens to
be processed by the same thread.
There's a more subtle problem here too:
An NFSv4 compound request is decoded all in one pass before any
operations are executed.
Currently we're setting current->fs->umask at the time we decode the
compound. In theory a single compound could contain multiple creates
each setting a umask. In that case we'd end up using whichever umask
was passed in the *last* operation as the umask for all the creates,
whether that was correct or not.
So, we should just be saving the umask at decode time and waiting to set
it until we actually process the corresponding operation.
In practice it's unlikely any client would do multiple creates in a
single compound. And even if it did they'd likely be from the same
process (hence carry the same umask). So this is a little academic, but
we should get it right anyway.
Fixes: 47057abde515 (nfsd: add support for the umask attribute) Cc: stable@vger.kernel.org Reported-by: Lucash Stach <l.stach@pengutronix.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a fix for a regression in 32 bit kernels caused by an invalid
check for pgoff overflow in hugetlbfs mmap setup. The check incorrectly
specified that the size of a loff_t was the same as the size of a long.
The regression prevents mapping hugetlbfs files at offsets greater than
4GB on 32 bit kernels.
On 32 bit kernels conversion from a page based unsigned long can not
overflow a loff_t byte offset. Therefore, skip this check if
sizeof(unsigned long) != sizeof(loff_t).
Link: http://lkml.kernel.org/r/20180330145402.5053-1-mike.kravetz@oracle.com Fixes: 63489f8e8211 ("hugetlbfs: check for pgoff value overflow") Reported-by: Dan Rue <dan.rue@linaro.org> Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Tested-by: Anders Roxell <anders.roxell@linaro.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Nic Losby <blurbdust@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple
concurrent xenstore accesses") made a subtle change to the semantic of
xenbus_dev_request_and_reply() and xenbus_transaction_end().
Before on an error response to XS_TRANSACTION_END
xenbus_dev_request_and_reply() would not decrement the active
transaction counter. But xenbus_transaction_end() has always counted the
transaction as finished regardless of the response.
The new behavior is that xenbus_dev_request_and_reply() and
xenbus_transaction_end() will always count the transaction as finished
regardless the response code (handled in xs_request_exit()).
But xenbus_dev_frontend tries to end a transaction on closing of the
device if the XS_TRANSACTION_END failed before. Trying to close the
transaction twice corrupts the reference count. So fix this by also
considering a transaction closed if we have sent XS_TRANSACTION_END once
regardless of the return code.
As of now if we encounter an opaque dir while looking for a dentry, we set
d->last=true. This means that there is no need to look further in any of
the lower layers. This works fine as long as there are no redirets or
relative redircts. But what if there is an absolute redirect on the
children dentry of opaque directory. We still need to continue to look into
next lower layer. This patch fixes it.
Here is an example to demonstrate the issue. Say you have following setup.
upper: /redirect (redirect=/a/b/c)
lower1: /a/[b]/c ([b] is opaque) (c has absolute redirect=/a/b/d/)
lower0: /a/b/d/foo
Now "redirect" dir should merge with lower1:/a/b/c/ and lower0:/a/b/d.
Note, despite the fact lower1:/a/[b] is opaque, we need to continue to look
into lower0 because children c has an absolute redirect.
From commit 4b855ad37194 ("blk-mq: Create hctx for each present CPU),
blk-mq doesn't remap queue after CPU topo is changed, that said when
some of these offline CPUs become online, they are still mapped to
hctx 0, then hctx 0 may become the bottleneck of IO dispatch and
completion.
This patch sets up the mapping from the beginning, and aligns to
queue mapping for PCI device (blk_mq_pci_map_queues()).
Cc: Stefan Haberland <sth@linux.vnet.ibm.com> Cc: Keith Busch <keith.busch@intel.com> Cc: stable@vger.kernel.org Fixes: 4b855ad37194 ("blk-mq: Create hctx for each present CPU) Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch orders getting budget and driver tag by making sure to acquire
driver tag after budget is got, this way can help to avoid the following
race:
1) before dispatch request from scheduler queue, get one budget first, then
dequeue a request, call it request A.
2) in another IO path for dispatching request B which is from hctx->dispatch,
driver tag is got, then try to get budget in blk_mq_dispatch_rq_list(),
unfortunately the budget is held by request A.
3) meantime blk_mq_dispatch_rq_list() is called for dispatching request
A, and try to get driver tag first, unfortunately no driver tag is
available because the driver tag is held by request B
4) both two IO pathes can't move on, and IO stall is caused.
This issue can be observed when running dbench on USB storage.
This patch fixes this issue by always getting budget before getting
driver tag.
Cc: stable@vger.kernel.org Fixes: de1482974080ec9e ("blk-mq: introduce .get_budget and .put_budget in blk_mq_ops") Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a task is holding a reference to a namespace on a removed controller,
the head will not be released. If the same controller is added again
later, its namespaces may not be successfully added. Instead, the user
will see kernel message "Duplicate IDs for nsid <X>".
This patch fixes that by skipping heads that don't have namespaces when
considering if a new namespace is safe to add.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com> Cc: stable@vger.kernel.org Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scsi_device_quiesce() uses synchronize_rcu() to guarantee that the
effect of blk_set_preempt_only() will be visible for percpu_ref_tryget()
calls that occur after the queue unfreeze by using the approach
explained in https://lwn.net/Articles/573497/. The rcu read lock and
unlock calls in blk_queue_enter() form a pair with the synchronize_rcu()
call in scsi_device_quiesce(). Both scsi_device_quiesce() and
blk_queue_enter() must either use regular RCU or RCU-sched.
Since neither the RCU-protected code in blk_queue_enter() nor
blk_queue_usage_counter_release() sleeps, regular RCU protection
is sufficient. Note: scsi_device_quiesce() does not have to be
modified since it already uses synchronize_rcu().
Reported-by: Tejun Heo <tj@kernel.org> Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Hannes Reinecke <hare@suse.com> Cc: Ming Lei <ming.lei@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Oleksandr Natalenko <oleksandr@natalenko.name> Cc: Martin Steigerwald <martin@lichtvoll.de> Cc: stable@vger.kernel.org # v4.15 Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a20b8a61eff81bdb7097a578752a74860e9d142 ("f2fs: allocate node
and hot data in the beginning of partition") introduces another mount
option, heap, to reset it back. But it does not do anything for heap
mode, so fix it.
Cc: stable@vger.kernel.org Signed-off-by: Yunlong Song <yunlong.song@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is wrong because it makes no sense to init() the request before a
key has been set, given that the initial state depends on the key. And
digest() is short for init() + update() + final(), so in this case
there's no need to explicitly call init() at all.
Before commit 9fa68f620041 ("crypto: hash - prevent using keyed hashes
without setting key") the extra init() had no real effect, at least for
the software HMAC implementation. (There are also hardware drivers that
implement HMAC-MD5, and it's not immediately obvious how gracefully they
handle init() before setkey().) But now the crypto API detects this
incorrect initialization and returns -ENOKEY. This is breaking NFS
mounts in some cases.
Fix it by removing the incorrect call to crypto_ahash_init().
Reported-by: Michael Young <m.a.young@durham.ac.uk> Fixes: 9fa68f620041 ("crypto: hash - prevent using keyed hashes without setting key") Fixes: fffdaef2eb4a ("gss_krb5: Add support for rc4-hmac encryption") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The APIC ID as parsed from ACPI MADT is validity checked with the
apic->apic_id_valid() callback, which depends on the selected APIC type.
For non X2APIC types APIC IDs >= 0xFF are invalid, but values > 0x7FFFFFFF
are detected as valid. This happens because the 'apicid' argument of the
apic_id_valid() callback is type 'int'. So the resulting comparison
apicid < 0xFF
evaluates to true for all unsigned int values > 0x7FFFFFFF which are handed
to default_apic_id_valid(). As a consequence, invalid APIC IDs in !X2APIC
mode are considered valid and accounted as possible CPUs.
Change the apicid argument type of the apic_id_valid() callback to u32 so
the evaluation is unsigned and returns the correct result.
[ tglx: Massaged changelog ]
Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Cc: jgross@suse.com Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: hpa@zytor.com Link: https://lkml.kernel.org/r/1523322966-10296-1-git-send-email-lirongqing@baidu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf9809 ("ath9k: Switch to using mac80211 intermediate software queues.") Cc: stable@vger.kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize data->config_lock mutex before it is used by the driver code.
This fixes following warning on Odroid XU3 boards:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180115-00001-gb75575dee3f2 #107
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0111504>] (unwind_backtrace) from [<c010dbec>] (show_stack+0x10/0x14)
[<c010dbec>] (show_stack) from [<c09b3f74>] (dump_stack+0x90/0xc8)
[<c09b3f74>] (dump_stack) from [<c0179528>] (register_lock_class+0x1c0/0x59c)
[<c0179528>] (register_lock_class) from [<c017bd1c>] (__lock_acquire+0x78/0x1850)
[<c017bd1c>] (__lock_acquire) from [<c017de30>] (lock_acquire+0xc8/0x2b8)
[<c017de30>] (lock_acquire) from [<c09ca59c>] (__mutex_lock+0x60/0xa0c)
[<c09ca59c>] (__mutex_lock) from [<c09cafd0>] (mutex_lock_nested+0x1c/0x24)
[<c09cafd0>] (mutex_lock_nested) from [<c068b0d0>] (ina2xx_set_shunt+0x70/0xb0)
[<c068b0d0>] (ina2xx_set_shunt) from [<c068b218>] (ina2xx_probe+0x88/0x1b0)
[<c068b218>] (ina2xx_probe) from [<c0673d90>] (i2c_device_probe+0x1e0/0x2d0)
[<c0673d90>] (i2c_device_probe) from [<c053a268>] (driver_probe_device+0x2b8/0x4a0)
[<c053a268>] (driver_probe_device) from [<c053a54c>] (__driver_attach+0xfc/0x120)
[<c053a54c>] (__driver_attach) from [<c05384cc>] (bus_for_each_dev+0x58/0x7c)
[<c05384cc>] (bus_for_each_dev) from [<c0539590>] (bus_add_driver+0x174/0x250)
[<c0539590>] (bus_add_driver) from [<c053b5e0>] (driver_register+0x78/0xf4)
[<c053b5e0>] (driver_register) from [<c0675ef0>] (i2c_register_driver+0x38/0xa8)
[<c0675ef0>] (i2c_register_driver) from [<c0102b40>] (do_one_initcall+0x48/0x18c)
[<c0102b40>] (do_one_initcall) from [<c0e00df0>] (kernel_init_freeable+0x110/0x1d4)
[<c0e00df0>] (kernel_init_freeable) from [<c09c8120>] (kernel_init+0x8/0x114)
[<c09c8120>] (kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Fixes: 5d389b125186 ("hwmon: (ina2xx) Make calibration register value fixed") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The block address is saved after the block is initialized when
threshold_init_device() is called.
Use the saved block address, if available, rather than trying to
rediscover it.
This will avoid a call trace, when resuming from suspend, due to the
rdmsr_safe_on_cpu() call in get_block_address(). The rdmsr_safe_on_cpu()
call issues an IPI but we're running with interrupts disabled. This
triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
A use-after-free bug was caught by KASAN while running usdt related
code (BCC project. bcc/tests/python/test_usdt2.py):
==================================================================
BUG: KASAN: use-after-free in uprobe_perf_close+0x222/0x3b0
Read of size 4 at addr ffff880384f9b4a4 by task test_usdt2.py/870
The buggy address belongs to the object at ffff880384f9b480
which belongs to the cache task_struct of size 12928
It occurs because task_struct is freed before perf_event which refers
to the task and task flags are checked while teardown of the event.
perf_event_alloc() assigns task_struct to hw.target of perf_event,
but there is no reference counting for it.
As a fix we get_task_struct() in perf_event_alloc() at above mentioned
assignment and put_task_struct() in _free_event().
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 63b6da39bb38e8f1a1ef3180d32a39d6 ("perf: Fix perf_event_exit_task() race") Link: http://lkml.kernel.org/r/20180409100346.6416-1-bhole_prashant_q7@lab.ntt.co.jp Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I suspect the reason is the per-cpu data is not in the linear chunk.
This could be restored if that was able to be fixed, but for now,
just remove the tracepoints.
1. With the patch "x86/vector/msi: Switch to global reservation mode",
the recent v4.15 and newer kernels always hang for 1-vCPU Hyper-V VM
with SR-IOV. This is because when we reach hv_compose_msi_msg() by
request_irq() -> request_threaded_irq() ->__setup_irq()->irq_startup()
-> __irq_startup() -> irq_domain_activate_irq() -> ... ->
msi_domain_activate() -> ... -> hv_compose_msi_msg(), local irq is
disabled in __setup_irq().
Note: when we reach hv_compose_msi_msg() by another code path:
pci_enable_msix_range() -> ... -> irq_domain_activate_irq() -> ... ->
hv_compose_msi_msg(), local irq is not disabled.
hv_compose_msi_msg() depends on an interrupt from the host.
With interrupts disabled, a UP VM always hangs in the busy loop in
the function, because the interrupt callback hv_pci_onchannelcallback()
can not be called.
We can do nothing but work it around by polling the channel. This
is ugly, but we don't have any other choice.
2. If the host is ejecting the VF device before we reach
hv_compose_msi_msg(), in a UP VM, we can hang in hv_compose_msi_msg()
forever, because at this time the host doesn't respond to the
CREATE_INTERRUPT request. This issue exists the first day the
pci-hyperv driver appears in the kernel.
Luckily, this can also by worked around by polling the channel
for the PCI_EJECT message and hpdev->state, and by checking the
PCI vendor ID.
Note: actually the above 2 issues also happen to a SMP VM, if
"hbus->hdev->channel->target_cpu == smp_processor_id()" is true.
Fixes: 4900be83602b ("x86/vector/msi: Switch to global reservation mode") Tested-by: Adrian Suhov <v-adsuho@microsoft.com> Tested-by: Chris Valean <v-chvale@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: <stable@vger.kernel.org> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we hot-remove the device, we first receive a PCI_EJECT message and
then receive a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
The first message is offloaded to hv_eject_device_work(), and the second
is offloaded to pci_devices_present_work(). Both the paths can be running
list_del(&hpdev->list_entry), causing general protection fault, because
system_wq can run them concurrently.
The patch eliminates the race condition.
Since access to present/eject work items is serialized, we do not need the
hbus->enum_sem anymore, so remove it.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Link: https://lkml.kernel.org/r/KL1P15301MB00064DA6B4D221123B5241CFBFD70@KL1P15301MB0006.APCP153.PROD.OUTLOOK.COM Tested-by: Adrian Suhov <v-adsuho@microsoft.com> Tested-by: Chris Valean <v-chvale@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: squashed semaphore removal patch] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: <stable@vger.kernel.org> # v4.6+ Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pci-hyperv driver's channel callback hv_pci_onchannelcallback() is not
really a hot path, so we don't need to mark it as a perf_device, meaning
with this patch all HV_PCIE channels' target_cpu will be CPU0.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: stable@vger.kernel.org Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the HPMC (High Priority Machine Check) handler is 16-byte
aligned and that it's length in the IVT is a multiple of 16 bytes.
Otherwise PDC may decide not to call the HPMC crash handler.
As found by the ubsan checker, the value of the 'index' variable can be
out of range for the bc[] array:
UBSAN: Undefined behaviour in arch/parisc/kernel/drivers.c:655:21
index 6 is out of range for type 'char [6]'
Backtrace:
[<104fa850>] __ubsan_handle_out_of_bounds+0x68/0x80
[<1019d83c>] check_parent+0xc0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019d86c>] check_parent+0xf0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019d938>] descend_children+0x4c/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019cffc>] hwpath_to_device+0xa4/0xc4
device_remove_group() was called on any cleanup, even if the
device attrs had not been added yet. That can occur in certain
error scenarios, so add a flag to know if it has been added.
Also make sure we remove the dev if we added it ourselves.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: stable@vger.kernel.org # 4.15 Cc: Laura Abbott <labbott@redhat.com> Tested-by: Bill Perkins <wmp@grnwood.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow dual pipelines utilising two WPF entities when available, the
VSP was updated to support header-mode display list in continuous
pipelines.
A small bug in the status check of the command register causes the
second pipeline to be directly afflicted by the running of the first;
appearing as a perceived performance issue with stuttering display.
Fix the vsp1_dl_list_hw_update_pending() call to ensure that the read
comparison corresponds to the correct pipeline.
At put_v4l2_window32(), it tries to access kp->clips. However,
kp points to an userspace pointer. So, it should be obtained
via get_user(), otherwise it can OOPS:
lan78xx_read_otp tries to return -EINVAL in the event of invalid OTP
content, but the value gets overwritten before it is returned and the
read goes ahead anyway. Make the read conditional as it should be
and preserve the error code.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhost_copy_to_user is used to copy vring used elements to userspace.
We should use VHOST_ADDR_USED instead of VHOST_ADDR_DESC.
Fixes: f88949138058 ("vhost: introduce O(1) vq metadata cache") Signed-off-by: Eric Auger <eric.auger@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit dd9d598c6657 ("ip_gre: add the support for i/o_flags update via
netlink") added the ability to change o_flags, but missed that the
GSO/LLTX features are disabled by default, and only enabled some gre
features are unused. Thus we also need to disable the GSO/LLTX features
on the device when the TUNNEL_SEQ or TUNNEL_CSUM flags are set.
These two examples should result in the same features being set:
ip link add gre_none type gre local 192.168.0.10 remote 192.168.0.20 ttl 255 key 0
ip link set gre_none type gre seq
ip link add gre_seq type gre local 192.168.0.10 remote 192.168.0.20 ttl 255 key 1 seq
Fixes: dd9d598c6657 ("ip_gre: add the support for i/o_flags update via netlink") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use l2tp_tunnel_find() to prevent l2tp_nl_cmd_tunnel_create()
from creating a duplicate tunnel. A tunnel can be concurrently
registered after l2tp_tunnel_find() returns. Therefore, searching for
duplicates must be done at registration time.
Finally, remove l2tp_tunnel_find() entirely as it isn't use anywhere
anymore.
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_tunnel_create() inserts the new tunnel into the namespace's tunnel
list and sets the socket's ->sk_user_data field, before returning it to
the caller. Therefore, there are two ways the tunnel can be accessed
and freed, before the caller even had the opportunity to take a
reference. In practice, syzbot could crash the module by closing the
socket right after a new tunnel was returned to pppol2tp_create().
This patch moves tunnel registration out of l2tp_tunnel_create(), so
that the caller can safely hold a reference before publishing the
tunnel. This second step is done with the new l2tp_tunnel_register()
function, which is now responsible for associating the tunnel to its
socket and for inserting it into the namespace's list.
While moving the code to l2tp_tunnel_register(), a few modifications
have been done. First, the socket validation tests are done in a helper
function, for clarity. Also, modifying the socket is now done after
having inserted the tunnel to the namespace's tunnels list. This will
allow insertion to fail, without having to revert theses modifications
in the error path (a followup patch will check for duplicate tunnels
before insertion). Either the socket is a kernel socket which we
control, or it is a user-space socket for which we have a reference on
the file descriptor. In any case, the socket isn't going to be closed
from under us.
Reported-by: syzbot+fbeeb5c3b538e8545644@syzkaller.appspotmail.com Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the patch the short-circuit logic for A was inverted:
if (A || vq->iotlb)
return A;
return B;
This patch fixes the regression by rewriting the checks in the obvious
way, no longer returning A when vq->iotlb is non-NULL (which is hard to
understand).
Reported-by: syzbot+65a84dde0214b0387ccd@syzkaller.appspotmail.com Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On receiving a packet the state index points to the rstate which must be
used to fill up IP and TCP headers. But if the state index points to a
rstate which is unitialized, i.e. filled with zeros, it gets stuck in an
infinite loop inside ip_fast_csum trying to compute the ip checsum of a
header with zero length.
./scripts/faddr2line vmlinux slhc_uncompress+0x464/0x468 output:
ip_fast_csum at arch/arm64/include/asm/checksum.h:40
(inlined by) slhc_uncompress at drivers/net/slip/slhc.c:615
Adding a variable to indicate if the current rstate is initialized. If
such a packet arrives, move to toss state.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rds_sendmsg() calls rds_send_mprds_hash() to find a c_path to use to
send a message. Suppose the RDS connection is not yet up. In
rds_send_mprds_hash(), it does
if (conn->c_npaths == 0)
wait_event_interruptible(conn->c_hs_waitq,
(conn->c_npaths != 0));
If it is interrupted before the connection is set up,
rds_send_mprds_hash() will return a non-zero hash value. Hence
rds_sendmsg() will use a non-zero c_path to send the message. But if
the RDS connection ends up to be non-MP capable, the message will be
lost as only the zero c_path can be used.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.
The modem is controlled via AT commands through the exposed TTYs.
AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.
In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.
v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)
Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369 Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit c0cfb10d9e1de490e36d3b9d4228c0ea0ca30677) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlx4_delete_all_resources_for_slave in resource tracker should free all
memory allocated for a slave.
While releasing memory of fs_rule, it misses releasing memory of
fs_rule->mirr_mbox.
Fixes: 78efed275117 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports') Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We try to hold TX virtqueue mutex in vhost_net_rx_peek_head_len()
after RX virtqueue mutex is held in handle_rx(). This requires an
appropriate lock nesting notation to calm down deadlock detector.
Fixes: 0308813724606 ("vhost_net: basic polling support") Reported-by: syzbot+7f073540b1384a614e09@syzkaller.appspotmail.com Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same fix as in 'bonding: move dev_mc_sync after master_upper_dev_link
in bond_enslave' is needed for team driver.
The panic can be reproduced easily:
ip link add team1 type team
ip link set team1 up
ip link add link team1 vlan1 type vlan id 80
ip link set vlan1 master team1
Fixes: cb41c997d444 ("team: team should sync the port's uc/mc addrs when add a port") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this patch, when one packet is hashed into path [1]
(hash <= nh_upper_bound) and it's neigh is dead, it will try
path [2]. However, if path [2]'s neigh is alive but it's
hash > nh_upper_bound, it will not return this alive path.
This packet will never be sent even if path [2] is alive.
3.3.3.1/24:
nexthop via 1.1.1.254 dev eth1 weight 1 <--[1] (dead neigh)
nexthop via 2.2.2.254 dev eth2 weight 1 <--[2]
With sysctl_fib_multipath_use_neigh set is supposed to find an
available path respecting to the l3/l4 hash. But if there is
no available route with this hash, it should at least return
an alive route even with other hash.
This patch is to fix it by processing fib_multipath_use_neigh
earlier than the hash check, so that it will at least return
an alive route if there is when fib_multipath_use_neigh is
enabled. It's also compatible with before when there are alive
routes with the l3/l4 hash.
Fixes: a6db4494d218 ("net: ipv4: Consider failed nexthops in multipath routes") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vq log_base is the userspace address of bitmap which has nothing to do
with IOTLB. So it needs to be validated unconditionally otherwise we
may try use 0 as log_base which may lead to pin pages that will lead
unexpected result (e.g trigger BUG_ON() in set_bit_to_user()).
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API") Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase representor netdev RQ size to avoid dropped packets.
The current size (two) is just too small to keep up with
conventional slow path traffic patterns.
Also match the SQ size to the RQ size.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Global pause and PFC configuration should be mutually exclusive (i.e. only
one of them at most can be set). However, once PFC was turned off,
driver automatically turned Global pause on. This is a bug.
Fix the driver behaviour to turn off PFC/Global once the user turned the
other on.
This also fixed a weird behaviour that at a current time, the profile
had both PFC and global pause configuration turned on, which is
Hardware-wise impossible and caused returning false positive indication
to query tools.
In addition, fix error code when setting global pause or PFC to change
metadata only upon successful change.
Also, removed useless debug print.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands") Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strp_parser_err is called with a negative code everywhere, which then
calls abort_parser with a negative code. strp_msg_timeout calls
abort_parser directly with a positive code. Negate ETIMEDOUT
to match signed-ness of other calls.
The default abort_parser callback, strp_abort_strp, sets
sk->sk_err to err. Also negate the error here so sk_err always
holds a positive value, as the rest of the net code expects. Currently
a negative sk_err can result in endless loops, or user code that
thinks it actually sent/received err bytes.
Found while testing net/tls_sw recv path.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Signed-off-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
# tc action replace action skbmod swap mac index 100
is run for the first time, and tcf_skbmod_init() fails to allocate struct
tcf_skbmod_params, tcf_skbmod_cleanup() calls kfree_rcu(NULL), thus
causing the following error:
is run for the first time, and tunnel_key_init() fails to allocate struct
tcf_tunnel_key_params, tunnel_key_release() dereferences NULL pointers.
This causes the following error:
When mlx5_core is loaded it is expected to sync ports
with all vxlan devices so it can support vxlan encap/decap.
This is done via udp_tunnel_get_rx_info(). Currently this
call is set in mlx5e_nic_enable() and if the netdev is not in
NETREG_REGISTERED state it will not be called.
Normally on load the netdev state is not NETREG_REGISTERED
so udp_tunnel_get_rx_info() will not be called.
Moving udp_tunnel_get_rx_info() to mlx5e_open() so
it will be called on netdev UP event and allow encap/decap.
Fixes: 610e89e05c3f ("net/mlx5e: Don't sync netdev state when not registered") Signed-off-by: Shahar Klein <shahark@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianbo Liu [Fri, 2 Mar 2018 02:09:08 +0000 (02:09 +0000)]
net/mlx5e: Don't override vport admin link state in switchdev mode
The vport admin original link state will be re-applied after returning
back to legacy mode, it is not right to change the admin link state value
when in switchdev mode.
Use direct vport commands to alter logical vport state in netdev
representor open/close flows rather than the administrative eswitch API.
Fixes: 20a1ea674783 ('net/mlx5e: Support VF vport link state control for SRIOV switchdev mode') Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling TSO can lead to abysmal performances when using seg6 in
encap mode, such as with the ixgbe driver. This patch adds a call to
iptunnel_handle_offloads() to remove the encapsulation bit if needed.
Before:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[ 4] local fc45::4 port 36592 connected to fc00::55 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 196 KBytes 1.60 Mbits/sec 47 6.66 KBytes
[ 4] 1.00-2.00 sec 304 KBytes 2.49 Mbits/sec 100 5.33 KBytes
[ 4] 2.00-3.00 sec 284 KBytes 2.32 Mbits/sec 92 5.33 KBytes
After:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[ 4] local fc45::4 port 43062 connected to fc00::55 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 1.03 GBytes 8.89 Gbits/sec 0 743 KBytes
[ 4] 1.00-2.00 sec 1.03 GBytes 8.87 Gbits/sec 0 743 KBytes
[ 4] 2.00-3.00 sec 1.03 GBytes 8.87 Gbits/sec 0 743 KBytes
Reported-by: Tom Herbert <tom@quantonium.net> Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NSP default buffer is a piece of NFP memory where additional
command data can be placed. Its format has been copied from
host buffer, but the PCIe selection bits do not make sense in
this case. If those get masked out from a NFP address - writes
to random place in the chip memory may be issued and crash the
device.
Even in the general NSP buffer case, it doesn't make sense to have the
PCIe selection bits there anymore. These are unused at the moment, and
when it becomes necessary, the PCIe selection bits should rather be
moved to another register to utilise more bits for the buffer address.
This has never been an issue because the buffer used to be
allocated in memory with less-than-38-bit-long address but that
is about to change.
Fixes: 1a64821c6af7 ("nfp: add support for service processor access") Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
# tc action add action sample rate 100 group 100 index 100
is run for the first time, and psample_group_get(100) fails to create a
new group, tcf_sample_cleanup() calls psample_group_put(NULL), thus
causing the following error:
For NIC flows, the parsed attributes are not freed when we exit
successfully from mlx5e_configure_flower().
There is possible double free for eswitch flows. If error is returned
from rhashtable_insert_fast(), the parse attrs will be freed in
mlx5e_tc_del_flow(), but they will be freed again before exiting
mlx5e_configure_flower().
To fix both issues we do the following:
(1) change the condition that determines if to issue the free call to
check if this flow is NIC flow, or it does not have encap action.
(2) reorder the code such that that the check and free calls are done
before we attempt to add into the hash table.
Fixes: 232c001398ae ('net/mlx5e: Add support to neighbour update flow') Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we use the global ipv6_stub var to access the ipv6 global
nd table. This practice gets us to troubles when the stub is only partially
set e.g when ipv6 is loaded under the disabled policy. In this case, as of commit 343d60aada5a ("ipv6: change ipv6_stub_impl.ipv6_dst_lookup to take net argument")
the stub is not null, but stub->nd_tbl is and we crash.
As we can access the ipv6 nd_tbl directly, the fix is just to avoid the
reference through the stub. There is one place in the code where we
issue ipv6 route lookup and keep doing it through the stub, but that
mentioned commit makes sure we get -EAFNOSUPPORT from the stack.
Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow") Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Aviv Heller <avivh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is run for the first time, and tcf_vlan_init() fails allocating struct
tcf_vlan_params, tcf_vlan_cleanup() calls kfree_rcu(NULL, ...). This causes
the following error:
When we delete a u32 key via u32_delete_key(), we forget to
call idr_remove() to remove its handle from IDR.
Fixes: e7614370d6f0 ("net_sched: use idr to allocate u32 filter handles") Reported-by: Marcin Kabiesz <admin@hostcenter.eu> Tested-by: Marcin Kabiesz <admin@hostcenter.eu> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default TX moderation mode was mistakenly set to CQE based. The
intention was to add a control ability in order to improve some specific
use-cases. In general, we prefer to use EQE based moderation as it gives
much better numbers for the common cases.
CQE based causes a degradation in the common case since it resets the
moderation timer on CQE generation. This causes an issue when TSO is
well utilized (large TSO sessions). The timer is set to 16us so traffic
of ~64KB TSO sessions per second would mean timer reset (CQE per TSO
session -> long time between CQEs). In this case we quickly reach the
tcp_limit_output_bytes (256KB by default) and cause a halt in TX traffic.
By setting EQE based moderation we make sure timer would expire after
16us regardless of the packet rate.
This fixes an up to 40% packet rate and up to 23% bandwidth degradtions.
Fixes: 0088cbbc4b66 ("net/mlx5e: Enable CQE based moderation on TX CQ") Signed-off-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ip6gre_tunnel_locate+0x334/0x860 net/ipv6/ip6_gre.c:339
Write of size 20 at addr ffff8801afb9f7b8 by task syzkaller851048/4466
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ipip6_tunnel_locate+0x63b/0xaa0 net/ipv6/sit.c:254
Write of size 33 at addr ffff8801b64076d8 by task syzkaller932654/4453
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_tunnel_create+0xca/0x6b0 net/ipv4/ip_tunnel.c:257
Write of size 20 at addr ffff8801ac79f810 by task syzkaller268107/4482
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to use dev_valid_name() to validate tunnel names,
so better use strnlen(name, IFNAMSIZ) than strlen(name) to make
sure to not upset KASAN.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dev_set_promiscuity(1) succeeds but dev_set_allmulti(1) fails,
dev_set_promiscuity(-1) should be done before going to the err path.
Otherwise, dev->promiscuity will leak.
Fixes: 7e1a1ac1fbaa ("bonding: Check return of dev_set_promiscuity/allmulti") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is actually a dead lock caused by sync slave hwaddr from master when
the master is the slave's 'slave'. This dead loop check is actually done
by netdev_master_upper_dev_link. However, Commit 1f718f0f4f97 ("bonding:
populate neighbour's private on enslave") moved it after dev_mc_sync.
This patch is to fix it by moving dev_mc_sync after master_upper_dev_link,
so that this loop check would be earlier than dev_mc_sync. It also moves
if (mode == BOND_MODE_8023AD) into if (!bond_uses_primary) clause as an
improvement.
Note team driver also has this issue, I will fix it in another patch.
Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave") Reported-by: Beniamino Galvani <bgalvani@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vlan_vids_add_by_dev is called right after dev hwaddr sync, so on
the err path it should unsync dev hwaddr. Otherwise, the slave
dev's hwaddr will never be unsync when this err happens.
Fixes: 1ff412ad7714 ("bonding: change the bond's vlan syncing functions with the standard ones") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miguel reported an skb use after free / double free in vrf_finish_output
when neigh_output returns an error. The vrf driver should return after
the call to neigh_output as it takes over the skb on error path as well.
Patch is a simplified version of Miguel's patch which was written for 4.9,
and updated to top of tree.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device") Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like function ethtool_get_ts_info(), we should also consider the
phy_driver ts_info call back. For example, driver dp83640.
Fixes: 37dd9255b2f6 ("vlan: Pass ethtool get_ts_info queries to real device.") Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We tried to remove vq poll from wait queue, but do not check whether
or not it was in a list before. This will lead double free. Fixing
this by switching to use vhost_poll_stop() which zeros poll->wqh after
removing poll from waitqueue to make sure it won't be freed twice.
Cc: Darren Kenny <darren.kenny@oracle.com> Reported-by: syzbot+c0272972b01b872e604a@syzkaller.appspotmail.com Fixes: 2b8b328b61c79 ("vhost_net: handle polling errors when setting backend") Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----address@SYSC_bind
Variable was created at:
SYSC_bind+0x6f/0x4b0 net/socket.c:1461
SyS_bind+0x54/0x80 net/socket.c:1460
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----addr@___sys_recvmsg
Variable was created at:
___sys_recvmsg+0xd5/0x810 net/socket.c:2172
__sys_recvmmsg+0x54e/0xdb0 net/socket.c:2313
Bytes 8-15 of 16 are uninitialized
==================================================================
Kernel panic - not syncing: panic_on_warn set ...
pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.
Fix this by calling pci_set_drvdata() before registering the
net_device.
This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.
The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once dst has been cached in socket via sk_setup_caps(),
it is illegal to call ip_rt_put() (or dst_release()),
since sk_setup_caps() did not change dst refcount.
We can still dereference it since we hold socket lock.
Caugth by syzbot :
BUG: KASAN: use-after-free in atomic_dec_return include/asm-generic/atomic-instrumented.h:198 [inline]
BUG: KASAN: use-after-free in dst_release+0x27/0xa0 net/core/dst.c:185
Write of size 4 at addr ffff8801c54dc040 by task syz-executor4/20088
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when tcf_bpf_init_from_ops() fails (e.g. because of program having invalid
number of instructions), tcf_bpf_cfg_cleanup() calls bpf_prog_put(NULL) or
bpf_prog_destroy(NULL). Unless CONFIG_BPF_SYSCALL is unset, this causes
the following error:
Fix it in tcf_bpf_cfg_cleanup(), ensuring that bpf_prog_{put,destroy}(f)
is called only when f is not NULL.
Fixes: bbc09e7842a5 ("net/sched: fix idr leak on the error path of tcf_bpf_init()") Reported-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a bug in the tcf_dump_walker function that can cause some actions
to not be reported when dumping a large number of actions. This issue
became more aggrevated when cookies feature was added. In particular
this issue is manifest when large cookie values are assigned to the
actions and when enough actions are created that the resulting table
must be dumped in multiple batches.
The number of actions returned in each batch is limited by the total
number of actions and the memory buffer size. With small cookies
the numeric limit is reached before the buffer size limit, which avoids
the code path triggering this bug. When large cookies are used buffer
fills before the numeric limit, and the erroneous code path is hit.
For example after creating 32 csum actions with the cookie aaaabbbbccccdddd
$ tc actions ls action csum
total acts 26
action order 0: csum (tcp) action continue
index 1 ref 1 bind 0
cookie aaaabbbbccccdddd
.....
action order 25: csum (tcp) action continue
index 26 ref 1 bind 0
cookie aaaabbbbccccdddd
total acts 6
action order 0: csum (tcp) action continue
index 28 ref 1 bind 0
cookie aaaabbbbccccdddd
......
action order 5: csum (tcp) action continue
index 32 ref 1 bind 0
cookie aaaabbbbccccdddd
Note that the action with index 27 is omitted from the report.
Fixes: 4b3550ef530c ("[NET_SCHED]: Use nla_nest_start/nla_nest_end")" Signed-off-by: Craig Dillabaugh <cdillaba@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx5 modify cq limits the coalescing time parameter to 12 bit
and coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
KMSAN reports use of uninitialized memory in the case when |alen| is
smaller than sizeof(struct sockaddr_nl), and therefore |nladdr| isn't
fully copied from the userspace.
Signed-off-by: Alexander Potapenko <glider@google.com> Fixes: 1da177e4c3f41524 ("Linux-2.6.12-rc2") Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of ip6_forward(), IPSTATS_MIB_OUTFORWDATAGRAMS and
IPSTATS_MIB_OUTOCTETS are incremented immediately before the NF_HOOK call
for NFPROTO_IPV6 / NF_INET_FORWARD. As a result, these counters get
incremented regardless of whether or not the netfilter hook allows the
packet to continue being processed. This change increments the counters
in ip6_forward_finish() so that it will not happen if the netfilter hook
chooses to terminate the packet, which is similar to how IPv4 works.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Donald reported that IPv6 route leaking between VRFs is not working.
The root cause is the strict argument in the call to rt6_lookup when
validating the nexthop spec.
ip6_route_check_nh validates the gateway and device (if given) of a
route spec. It in turn could call rt6_lookup (e.g., lookup in a given
table did not succeed so it falls back to a full lookup) and if so
sets the strict argument to 1. That means if the egress device is given,
the route lookup needs to return a result with the same device. This
strict requirement does not work with VRFs (IPv4 or IPv6) because the
oif in the flow struct is overridden with the index of the VRF device
to trigger a match on the l3mdev rule and force the lookup to its table.
The right long term solution is to add an l3mdev index to the flow
struct such that the oif is not overridden. That solution will not
backport well, so this patch aims for a simpler solution to relax the
strict argument if the route spec device is an l3mdev slave. As done
in other places, use the FLOWI_FLAG_SKIP_NH_OIF to know that the
RT6_LOOKUP_F_IFACE flag needs to be removed.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack") Reported-by: Donald Sharp <sharpd@cumulusnetworks.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb mac header is not necessarily set at the time skb_network_protocol()
is called. Use skb->data instead.
BUG: KASAN: slab-out-of-bounds in skb_network_protocol+0x46b/0x4b0 net/core/dev.c:2739
Read of size 2 at addr ffff8801b3097a0b by task syz-executor5/14242
Fixes: 19acc327258a ("gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pravin B Shelar <pshelar@ovn.org> Reported-by: Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com> Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>