When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
With CONFIG_KASAN, we get an overly long stack frame due to inlining
the register access functions:
drivers/media/tuners/r820t.c: In function 'generic_set_freq.isra.7':
drivers/media/tuners/r820t.c:1334:1: error: the frame size of 2880 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
This is caused by a gcc bug that has now been fixed in gcc-8.
To work around the problem, we can pass the register data
through a local variable that older gcc versions can optimize
out as well.
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
According to the comment added to exynos_dt_pmu_match[] in commit 8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b062 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ce0fa3e56ad2 ("x86/mm, mm/hwpoison: Clear PRESENT bit for kernel 1:1 mappings of poison pages")
... we added code to memory_failure() to unmap the page from the
kernel 1:1 virtual address space to avoid speculative access to the
page logging additional errors.
But memory_failure() may not always succeed in taking the page offline,
especially if the page belongs to the kernel. This can happen if
there are too many corrected errors on a page and either mcelog(8)
or drivers/ras/cec.c asks to take a page offline.
Since we remove the 1:1 mapping early in memory_failure(), we can
end up with the page unmapped, but still in use. On the next access
the kernel crashes :-(
There are also various debug paths that call memory_failure() to simulate
occurrence of an error. Since there is no actual error in memory, we
don't need to map out the page for those cases.
Revert most of the previous attempt and keep the solution local to
arch/x86/kernel/cpu/mcheck/mce.c. Unmap the page only when:
1) there is a real error
2) memory_failure() succeeds.
All of this only applies to 64-bit systems. 32-bit kernel doesn't map
all of memory into kernel space. It isn't worth adding the code to unmap
the piece that is mapped because nobody would run a 32-bit kernel on a
machine that has recoverable machine checks.
Signed-off-by: Tony Luck <tony.luck@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave <dave.hansen@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert (Persistent Memory) <elliott@hpe.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Cc: stable@vger.kernel.org #v4.14 Fixes: ce0fa3e56ad2 ("x86/mm, mm/hwpoison: Clear PRESENT bit for kernel 1:1 mappings of poison pages") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit 2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Add quirk to ensure a sync endpoint is properly configured.
This patch is a fix for same symptoms on Behringer UFX1204 as patch
from Albertto Aquirre on Dec 8 2016 for Axe-Fx II.
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
Thinkpad Dock device support for ALC298 platform.
It need to use SSID for the quirk table.
Because IdeaPad also has ALC298 platform.
Use verb for the quirk table will confuse.
The layout of the UAC2 Control request and response varies depending on
the request type. With the current implementation, only the Layout 2
Parameter Block (with the 2-byte sized RANGE attribute) is handled
properly. For the Control requests with the 1-byte sized RANGE attribute
(Bass Control, Mid Control, Tremble Control), the response is parsed
incorrectly.
This commit:
* fixes the wLength field value in the request
* fixes parsing the range values from the response
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0") Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 3cf32d180227 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit 6a623e076944 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e076944 ("mtd: nand: add ooblayout for old hamming layout") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a 9p request is successfully flushed, the server is expected to just
mark it as used without sending a 9p reply (ie, without writing data into
the buffer). In this case, virtqueue_get_buf() will return len == 0 and
we must not report a REQ_STATUS_RCVD status to the client, otherwise the
client will erroneously assume the request has not been flushed.
Cc: stable@vger.kernel.org Signed-off-by: Greg Kurz <groug@kaod.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The highest objectid, which is assigned to new inode, is decided at
the time of initializing fs roots. However, in cases where log replay
gets processed, the btree which fs root owns might be changed, so we
have to search it again for the highest objectid, otherwise creating
new inode would end up with -EEXIST.
cc: <stable@vger.kernel.org> v4.4-rc6+ Fixes: f32e48e92596 ("Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that btrfs_sync_log() bails out after one of the two
btrfs_write_marked_extents() which convert extent state's state bit into
EXTENT_NEED_WAIT from EXTENT_DIRTY/EXTENT_NEW, however only EXTENT_DIRTY
and EXTENT_NEW are searched by free_log_tree() so that those extent states
with EXTENT_NEED_WAIT lead to memory leak.
cc: <stable@vger.kernel.org> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases that the whole fs flips into readonly status due to failures in
critical sections, then log tree's blocks are still dirty, and this leads
to a crash during umount time, the crash is about use-after-free,
cc: <stable@vger.kernel.org> v3.12+ Fixes: 681ae50917df ("Btrfs: cleanup reserved space when freeing tree log on error") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
@cur_offset is not set back to what it should be (@cow_start) if
btrfs_next_leaf() returns something wrong, and the range [cow_start,
cur_offset) remains locked forever.
cc: <stable@vger.kernel.org> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org (v3.14+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Christie reports:
Starting in 4.14 iscsi logins will fail around 50% of the time.
Problem appears to be that iscsi_target_sk_data_ready() callback may
return without doing anything in case it finds the login work queue
is still blocked in sock_recvmsg().
Nicholas Bellinger says:
It would indicate users providing their own ->sk_data_ready() callback
must be responsible for waking up a kthread context blocked on
sock_recvmsg(..., MSG_WAITALL), when a second ->sk_data_ready() is
received before the first sock_recvmsg(..., MSG_WAITALL) completes.
So, do this and invoke the original data_ready() callback -- in
case of tcp sockets this takes care of waking the thread.
Disclaimer: I do not understand why this problem did not show up before
tcp prequeue removal.
(Drop WARN_ON usage - nab)
Reported-by: Mike Christie <mchristi@redhat.com> Bisected-by: Mike Christie <mchristi@redhat.com> Tested-by: Mike Christie <mchristi@redhat.com> Diagnosed-by: Nicholas Bellinger <nab@linux-iscsi.org> Fixes: e7942d0633c4 ("tcp: remove prequeue support") Signed-off-by: Florian Westphal <fw@strlen.de> Cc: stable@vger.kernel.org # 4.14+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If chap_server_compute_md5() fails early, e.g. via CHAP_N mismatch, then
crypto_free_shash() is called with a NULL pointer which gets
dereferenced in crypto_shash_tfm().
Fixes: 69110e3cedbb ("iscsi-target: Use shash and ahash") Suggested-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David Disseldorp <ddiss@suse.de> Cc: stable@vger.kernel.org # 4.6+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikulas reported a workload that saw bad performance, and figured
out what it was due to various other types of requests being
accounted as reads. Flush requests, for instance. Due to the
high latency of those, we heavily throttle the writes to keep
the latencies in balance. But they really should be accounted
as writes.
Fix this by checking the exact type of the request. If it's a
read, account as a read, if it's a write or a flush, account
as a write. Any other request we disregard. Previously everything
would have been mistakenly accounted as reads.
Michal Kalderon reports a BUG that occurs just after device removal:
[ 169.112490] rpcrdma: removing device qedr0 for 192.168.110.146:20049
[ 169.143909] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 169.181837] IP: rpcrdma_dma_unmap_regbuf+0xa/0x60 [rpcrdma]
The RPC/RDMA client transport attempts to allocate some resources
on demand. Registered buffers are one such resource. These are
allocated (or re-allocated) by xprt_rdma_allocate to hold RPC Call
and Reply messages. A hardware resource is associated with each of
these buffers, as they can be used for a Send or Receive Work
Request.
If a device is removed from under an NFS/RDMA mount, the transport
layer is responsible for releasing all hardware resources before
the device can be finally unplugged. A BUG results when the NFS
mount hasn't yet seen much activity: the transport tries to release
resources that haven't yet been allocated.
rpcrdma_free_regbuf() already checks for this case, so just move
that check to cover the DEVICE_REMOVAL case as well.
Reported-by: Michal Kalderon <Michal.Kalderon@cavium.com> Fixes: bebd031866ca ("xprtrdma: Support unplugging an HCA ...") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Michal Kalderon <Michal.Kalderon@cavium.com> Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 16f906d66cd7 ("xprtrdma: Reduce required number of send
SGEs") introduced the rpcrdma_ia::ri_max_send_sges field. This fixes
a problem where xprtrdma would not work if the device's max_sge
capability was small (low single digits).
At least RPCRDMA_MIN_SEND_SGES are needed for the inline parts of
each RPC. ri_max_send_sges is set to this value:
Then when marshaling each RPC, rpcrdma_args_inline uses that value
to determine whether the device has enough Send SGEs to convey an
NFS WRITE payload inline, or whether instead a Read chunk is
required.
More recently, commit ae72950abf99 ("xprtrdma: Add data structure to
manage RDMA Send arguments") used the ri_max_send_sges value to
calculate the size of an array, but that commit erroneously assumed
ri_max_send_sges contains a value similar to the device's max_sge,
and not one that was reduced by the minimum SGE count.
This assumption results in the calculated size of the sendctx's
Send SGE array to be too small. When the array is used to marshal
an RPC, the code can write Send SGEs into the following sendctx
element in that array, corrupting it. When the device's max_sge is
large, this issue is entirely harmless; but it results in an oops
in the provider's post_send method, if dev.attrs.max_sge is small.
So let's straighten this out: ri_max_send_sges will now contain a
value with the same meaning as dev.attrs.max_sge, which makes
the code easier to understand, and enables rpcrdma_sendctx_create
to calculate the size of the SGE array correctly.
Reported-by: Michal Kalderon <Michal.Kalderon@cavium.com> Fixes: 16f906d66cd7 ("xprtrdma: Reduce required number of send SGEs") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Michal Kalderon <Michal.Kalderon@cavium.com> Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When KASAN is enabled, the swapper page table contains many identical
mappings of the zero page, which can lead to a stall during boot whilst
the G -> nG code continually walks the same page table entries looking
for global mappings.
This patch sets the nG bit (bit 11, which is IGNORED) in table entries
after processing the subtree so we can easily skip them if we see them
a second time.
Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b75
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem") Cc: Stable <stable@vger.kernel.org> # 4.14+ Fix-suggested-by: Pkshih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3 Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpls_label_ok() validates that the 'platform_label' array index from a
userspace netlink message payload is valid. Under speculation the
mpls_label_ok() result may not resolve in the CPU pipeline until after
the index is used to access an array element. Sanitize the index to zero
to prevent userspace-controlled arbitrary out-of-bounds speculation, a
precursor for a speculative execution side channel vulnerability.
Cc: <stable@vger.kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For substring - sure, but what about something like "*a*b" and "a*b"?
AFAICS, filter_parse_regex() ends up with identical results in both
cases - MATCH_GLOB and *search = "a*b". And no way for the caller
to tell one from another.
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Commit 82616f9599a7 ("xen: remove tests for pvh mode in pure pv paths")
removed the check for autotranslation from {set,clear}_foreign_p2m_mapping
but those are called by grant-table.c also on PVH/HVM guests.
Cc: <stable@vger.kernel.org> # 4.14 Fixes: 82616f9599a7 ("xen: remove tests for pvh mode in pure pv paths") Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This feature bit restricts older clients from performing certain
maintenance operations against an image (e.g. clone, snap create).
krbd does not perform maintenance operations.
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent display node was also prematurely
freed.
Note that the display and timings node references are never put after a
successful dt-initialisation so the nodes would leak on later probe
deferrals and on driver unbind.
Fix child-node lookup during initialisation which was using the wrong
OF-helper and ended up searching the whole device tree depth-first
starting at the parent rather than just matching on its children.
To make things worse, the parent pci node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Any matching child interrupt-controller node was also leaked.
Certain Thunderbolt 1 controllers claim to support Command Completed events
(value of 0b in the No Command Completed Support field of the Slot
Capabilities register) but in reality they neither set the Command
Completed bit in the Slot Status register nor signal a Command Completed
interrupt:
All known newer chips (Redwood Ridge and onwards) set No Command Completed
Support, indicating that they do not support Command Completed events.
The user-visible impact is that after unplugging such a device, 2 seconds
elapse until pciehp is unbound. That's because on ->remove,
pcie_write_cmd() is called via pcie_disable_notification() and every call
to pcie_write_cmd() takes 2 seconds (1 second for each invocation of
pcie_wait_cmd()):
That by itself has always been unpleasant, but the situation has become
worse with commit cc27b735ad3a ("PCI/portdrv: Turn off PCIe services during
shutdown"): Now pciehp is unbound on ->shutdown. Because Thunderbolt
controllers typically have 4 hotplug ports, every reboot and shutdown is
now delayed by 8 seconds, plus another 2 seconds for every attached
Thunderbolt 1 device.
Thunderbolt hotplug slots are not physical slots that one inserts cards
into, but rather logical hotplug slots implemented in silicon. Devices
appear beyond those logical slots once a PCI tunnel is established on top
of the Thunderbolt Converged I/O switch. One would expect commands written
to the Slot Control register to be executed immediately by the silicon, so
for simplicity we always assume NoCompl+ for Thunderbolt ports.
Fixes: cc27b735ad3a ("PCI/portdrv: Turn off PCIe services during shutdown") Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org # v4.12+ Cc: Sinan Kaya <okaya@codeaurora.org> Cc: Yehezkel Bernat <yehezkel.bernat@intel.com> Cc: Michael Jamet <michael.jamet@intel.com> Cc: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the inbound DMA mapping supported added, the iProc PCIe driver
parses DT property "dma-ranges" through call to
"of_pci_dma_range_parser_init()". In the case of BCMA, this results in a
NULL pointer deference due to a missing of_node.
Fix this by adding a guard in pcie-iproc-platform.c to only enable the
inbound DMA mapping logic when DT property "dma-ranges" is present.
HiSilicon Hip06/Hip07 can operate as either a Root Port or an Endpoint. It
always advertises an MSI capability, but it can only generate MSIs when in
Endpoint mode.
The device has the same Vendor and Device IDs in both modes, so check the
Class Code and disable MSI only when operating as a Root Port.
Commit 73fbc1eba7ff ("MIPS: fix mem=X@Y commandline processing") added a
fix to ensure that the memory range between PHYS_OFFSET and low memory
address specified by mem= cmdline argument is not later processed by
free_all_bootmem. This change was incorrect for systems where the
commandline specifies more than 1 mem argument, as it will cause all
memory between PHYS_OFFSET and each of the memory offsets to be marked
as reserved, which results in parts of the RAM marked as reserved
(Creator CI20's u-boot has a default commandline argument 'mem=256M@0x0
mem=768M@0x30000000').
Change the behaviour to ensure that only the range between PHYS_OFFSET
and the lowest start address of the memories is marked as protected.
This change also ensures that the range is marked protected even if it's
only defined through the devicetree and not only via commandline
arguments.
Commit 17278a91e04f ("MIPS: CPS: Fix r1 .set mt assembler warning")
added .set MIPS_ISA_LEVEL_RAW to silence warnings about .set mt on r1,
however this can result in a MOVE being encoded as a 64-bit DADDU
instruction on certain version of binutils (e.g. 2.22), and reserved
instruction exceptions at runtime on 32-bit hardware.
Reduce the sizes of the push/pop sections to include only instructions
that are part of the MT ASE or which won't convert to 64-bit
instructions after .set mips64r2/mips64r6.
MIPS_GENERIC selects some options conditional on BIG_ENDIAN which does
not exist.
Replace BIG_ENDIAN with CPU_BIG_ENDIAN which is the correct kconfig
name. Note that BMIPS_GENERIC does the same which confirms that this
patch is needed.
The functions devm_memremap_pages() and devm_memremap_pages_release() use
different ways to calculate the section-aligned amount of memory. The
latter function may use an incorrect size if the memory region is small
but straddles a section border.
Use the same code for both.
Cc: <stable@vger.kernel.org> Fixes: 5f29a77cd957 ("mm: fix mixed zone detection in devm_memremap_pages") Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function __ext4_grp_locked_error(), __save_error_info()
is called to save error info in super block block, but does not sync
that information to disk to info the subsequence fsck after reboot.
This patch writes the error information to disk. After this patch,
I think there is no obvious EXT4 error handle branches which leads to
"Remounting filesystem read-only" will leave the disk partition miss
the subsequence fsck.
This patch fixes a race between the shutdown path and bio completion
handling. In the ext4 direct io path with async io, after submitting a
bio to the block layer, if journal starting fails,
ext4_direct_IO_write() would bail out pretending that the IO
failed. The caller would have had no way of knowing whether or not the
IO was successfully submitted. So instead, we return -EIOCBQUEUED in
this case. Now, the caller knows that the IO was submitted. The bio
completion handler takes care of the error.
Tested: Ran the shutdown xfstest test 461 in loop for over 2 hours across
4 machines resulting in over 400 runs. Verified that the race didn't
occur. Usually the race was seen in about 20-30 iterations.
Sphinx emits various (26) warnings when building make target 'htmldocs'.
Currently struct definitions contain duplicate documentation, some as
kernel-docs and some as standard c89 comments. We can reduce
duplication while cleaning up the kernel docs.
Move all kernel-docs to right above each struct member. Use the set of
all existing comments (kernel-doc and c89). Add documentation for
missing struct members and function arguments.
Commit 4eebd5a4e726 ("apple-gmux: lock iGP IO to protect from vgaarb
changes") amended this driver's ->probe hook to lock decoding of normal
(non-legacy) I/O space accesses to the integrated GPU on dual-GPU
MacBook Pros. The lock stays in place until the driver is unbound.
The change was made to work around an issue with the out-of-tree nvidia
graphics driver (available at http://www.nvidia.com/object/unix.html).
It contains the following sequence in nvidia/nv.c:
This code was reported to cause deadlocks with VFIO already in 2013:
https://devtalk.nvidia.com/default/topic/545560
I've reported the issue to Nvidia developers once more in 2017:
https://www.spinics.net/lists/dri-devel/msg138754.html
On the MacBookPro10,1, this code apparently breaks backlight control
(which is handled by apple-gmux via an I/O region starting at 0x700),
as reported by Petri Hodju:
https://bugzilla.kernel.org/show_bug.cgi?id=86121
I tried to replicate Petri's observations on my MacBook9,1, which uses
the same Intel Ivy Bridge + Nvidia GeForce GT 650M architecture, to no
avail. On my machine apple-gmux' I/O region remains accessible even
with the nvidia driver loaded and commit 4eebd5a4e726 reverted.
Petri reported that apple-gmux becomes accessible again after a
suspend/resume cycle because the BIOS changed the VGA routing on the
root port to the Nvidia GPU. Perhaps this is a BIOS issue after all
that can be fixed with an update?
In any case, the change made by commit 4eebd5a4e726 has turned out to
cause two new issues:
* Wilfried Klaebe reports a deadlock when launching Xorg because it
opens /dev/vga_arbiter and calls vga_get(), but apple-gmux is holding
a lock on I/O space indefinitely. It looks like apple-gmux' current
behavior is an abuse of the vgaarb API as locks are not meant to be
held for longer periods:
https://bugzilla.kernel.org/show_bug.cgi?id=88861#c11
https://bugzilla.kernel.org/attachment.cgi?id=217541
* On dual GPU MacBook Pros introduced since 2013, the integrated GPU is
powergated on boot und thus becomes invisible to Linux unless a custom
EFI protocol is used to leave it powered on. (A patch exists but is
not in mainline yet due to several negative side effects.) On these
machines, locking I/O to the integrated GPU (as done by 4eebd5a4e726)
fails and backlight control is therefore broken:
https://bugzilla.kernel.org/show_bug.cgi?id=105051
So let's revert commit 4eebd5a4e726 please. Users experiencing the
issue with the proprietary nvidia driver can comment out the above-
quoted problematic code as a workaround (or try updating the BIOS).
Cc: Petri Hodju <petrihodju@yahoo.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Bruno Prémont <bonbons@linux-vserver.org> Cc: Andy Ritger <aritger@nvidia.com> Cc: Ronald Tschalär <ronald@innovation.ch> Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The consumers of this routine expects the affinity map of of vector
index relative to the first completion vector. The upper layers are
not aware of internal/private completion vectors that mlx5 allocates
for its own usage.
Hence, return the affinity map of vector index relative to the first
completion vector.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627d1 ("mmc: meson-gx: include tx phase in the tuning process") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
According to the OPAL docs:
skiboot-5.2.5/doc/opal-api/opal-rtc-read-3.txt
skiboot-5.2.5/doc/opal-api/opal-rtc-write-4.txt
OPAL_HARDWARE may be returned from OPAL_RTC_READ or OPAL_RTC_WRITE and
this indicates either a transient or permanent error.
Prior to this patch, Linux was not dealing with OPAL_HARDWARE being a
permanent error particularly well, in that you could end up in a busy
loop.
This was not too hard to trigger on an AMI BMC based OpenPOWER machine
doing a continuous "ipmitool mc reset cold" to the BMC, the result of
that being that we'd get stuck in an infinite loop in
opal_get_rtc_time().
We now retry a few times before returning the error higher up the
stack.
Fixes: 16b1d26e77b1 ("rtc/tpo: Driver to support rtc and wakeup on PowerNV platform") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uncore_pci_remove() runs, it tries to get the package ID to
clear the value of uncore_extra_pci_dev[].dev[] by using
topology_phys_to_logical_pkg(). The warning messesages are
shown because topology_phys_to_logical_pkg() returns -1.
Check the variable that was most recently initialized.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, y, f, g, e, m;
statement S1,S2,S3,S4;
@@
x = f(...);
if (\(<+...x...+>\&e\)) S1 else S2
(
x = g(...);
|
m = g(...,&x,...);
|
y = g(...);
*if (e)
S3 else S4
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
References to CPU part number MIDR_QCOM_FALKOR were dropped from the
mailing list patch due to mainline/arm64 branch dependency. So this
patch adds the missing part number.
Don't let a lessee control what the current DRM master is set to;
that's the job of the "real" master. Otherwise, the lessee would
disable all access to master operations for the owner and all lessees
under it.
This matches the same check made in the SET_MASTER ioctl.
QXL associates mouse state with its primary plane.
Destroying a primary plane and putting a new one in place has the side
effect of destroying the cursor as well.
This commit changes the driver to reapply the cursor any time a new
primary is created. It achieves this by keeping a reference to the
cursor bo on the qxl_crtc struct.
This fix is very similar to
commit 4532b241a4b7 ("drm/qxl: reapply cursor after SetCrtc calls")
which got implicitly reverted as part of implementing the atomic
modeset feature.
Cc: Gerd Hoffmann <kraxel@redhat.com> Cc: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1512097 Fixes: 1277eed5fecb ("drm: qxl: Atomic phase 1: convert cursor to universal plane") Cc: stable@vger.kernel.org Signed-off-by: Ray Strode <rstrode@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buf pointer was not being incremented inside the loop
meaning the same block of data would be read or written
repeatedly.
(v2) Change 'buf' pointer to uint8_t* type
Cc: stable@vger.kernel.org Fixes: 09ac4fcb3f25 ("drm/ttm: Implement vm_operations_struct.access v2") Signed-off-by: Tom St Denis <tom.stdenis@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A BO that's already swapped would be added back to the swap-LRU list
for example if its validation failed under high memory pressure. This
could later lead to swapping it out again and leaking previous swap
storage.
This commit adds a condition to prevent that from happening.
v2: Check page_flags instead of swap_storage
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"The paranoid exit code only restores the saved CR3 when it switches back
to the user GS. However, even in the kernel GS case, it's possible that
it needs to restore a user CR3, if for example, the paranoid exception
occurred in the syscall exit path between SWITCH_TO_USER_CR3_STACK and
SWAPGS."
Josh also confirmed via targeted testing that it's possible to hit this bug.
Fix the bug by also restoring CR3 in the paranoid_exit_no_swapgs branch.
The reason we haven't seen this bug reported by users yet is probably because
"paranoid" entry points are limited to the following cases:
Amongst those entry points only machine_check is one that will interrupt an
IRQS-off critical section asynchronously - and machine check events are rare.
The other main asynchronous entries are NMI entries, which can be very high-freq
with perf profiling, but they are special: they don't use the 'idtentry' macro but
are open coded and restore user CR3 unconditionally so don't have this bug.
Reported-and-tested-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Andy Lutomirski <luto@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180214073910.boevmg65upbk3vqb@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, x86_cache_size is of type int, which makes no sense as we
will never have a valid cache size equal or less than 0. So instead of
initializing this variable to -1, it can perfectly be initialized to 0
and use it as an unsigned variable instead.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org>
Addresses-Coverity-ID: 1464429 Link: http://lkml.kernel.org/r/20180213192208.GA26414@embeddedor.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_tlb_single() and flush_tlb_one() sound almost identical, but
they really mean "flush one user translation" and "flush one kernel
translation". Rename them to flush_tlb_one_user() and
flush_tlb_one_kernel() to make the semantics more obvious.
[ I was looking at some PTI-related code, and the flush-one-address code
is unnecessarily hard to understand because the names of the helpers are
uninformative. This came up during PTI review, but no one got around to
doing it. ]
Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Linux-MM <linux-mm@kvack.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: http://lkml.kernel.org/r/3303b02e3c3d049dc5235d5651e0ae6d29a34354.1517414378.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Konno reported a compile failure resulting from using an MSR
without inclusion of <asm/msr-index.h>, and while the current code builds
fine (by accident) this needs fixing for future patches.
For architectures providing their own implementation of
array_index_mask_nospec() in asm/barrier.h, attempting to use WARN_ONCE() to
complain about out-of-range parameters using WARN_ON() results in a mess
of mutually-dependent include files.
Rather than unpick the dependencies, simply have the core code in nospec.h
perform the checking for us.
Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1517840166-15399-1-git-send-email-will.deacon@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the Intel SDM added an ModR/M byte to UD0 and binutils followed
that specification, we now cannot disassemble our kernel anymore.
This now means Intel and AMD disagree on the encoding of UD0. And instead
of playing games with additional bytes that are valid ModR/M and single
byte instructions (0xd6 for instance), simply use UD2 for both WARN() and
BUG().
Requested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180208194406.GD25181@hirez.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, objtool assumes that a UD2 is a dead end. This is mainly
because GCC 7+ sometimes inserts a UD2 when it detects a divide-by-zero
condition.
Now that WARN() is moving back to UD2, annotate the code after it as
reachable so objtool can follow the code flow.
Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kbuild test robot <fengguang.wu@intel.com> Link: http://lkml.kernel.org/r/0e483379275a42626ba8898117f918e1bf661e40.1518130694.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra's patch for converting WARN() to use UD2 triggered a
bunch of false "unreachable instruction" warnings, which then triggered
a seg fault in ignore_unreachable_insn().
The seg fault happened when it tried to dereference a NULL 'insn->func'
pointer. Thanks to static_cpu_has(), some functions can jump to a
non-function area in the .altinstr_aux section. That breaks
ignore_unreachable_insn()'s assumption that it's always inside the
original function.
Make sure ignore_unreachable_insn() only follows jumps within the
current function.
Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kbuild test robot <fengguang.wu@intel.com> Link: http://lkml.kernel.org/r/bace77a60d5af9b45eddb8f8fb9c776c8de657ef.1518130694.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ldt_gdt and ptrace_syscall selftests, even in their 64-bit variant, use
hard-coded 32-bit syscall numbers and call "int $0x80".
This will fail on 64-bit systems with CONFIG_IA32_EMULATION=y disabled.
Therefore, do not build these tests if we cannot build 32-bit binaries
(which should be a good approximation for CONFIG_IA32_EMULATION=y being enabled).
On 64-bit builds, we should not rely on "int $0x80" working (it only does if
CONFIG_IA32_EMULATION=y is enabled). To keep the "Set TF and check int80"
test running on 64-bit installs with CONFIG_IA32_EMULATION=y enabled, build
this test only if we can also build 32-bit binaries (which should be a
good approximation for that).
It turns out that commit 3974320ca6 "Implement iomap for block_map"
introduced a few bugs that trigger occasional failures with xfstest
generic/476:
In gfs2_iomap_begin, we jump to do_alloc when we determine that we are
beyond the end of the allocated metadata (height > ip->i_height).
There, we can end up calling hole_size with a metapath that doesn't
match the current metadata tree, which doesn't make sense. After
untangling the code at do_alloc, fix this by checking if the block we
are looking for is within the range of allocated metadata.
In addition, add a BUG() in case gfs2_iomap_begin is accidentally called
for reading stuffed files: this is handled separately. Make sure we
don't truncate iomap->length for reads beyond the end of the file; in
that case, the entire range counts as a hole.
Finally, revert to taking a bitmap write lock when doing allocations.
It's unclear why that change didn't lead to any failures during testing.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
protection_keys.c: In function ‘dumpit’:
protection_keys.c:419:3: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result [-Wunused-result]
write(1, buf, nr_read);
^~~~~~~~~~~~~~~~~~~~~~
Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a couple of magically connected buffer length literal constants with
a common definition that makes their relationship obvious. Also document
why our sscanf() usage is safe.
The vDSO selftest tries to execute a vsyscall unconditionally, even if it
is not present on the test system (e.g. if booted with vsyscall=none or
with CONFIG_LEGACY_VSYSCALL_NONE=y set. Fix this by copying (and tweaking)
the vsyscall check from test_vsyscall.c
f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros")
... one of my suggested improvements triggered a frame pointer warning:
arch/x86/entry/entry_64.o: warning: objtool: paranoid_entry()+0x11: call without frame pointer save/setup
The warning is correct for the build-time code, but it's actually not
relevant at runtime because of paravirt patching. The paravirt swapgs
call gets replaced with either a SWAPGS instruction or NOPs at runtime.
Go back to the previous behavior by removing the ELF function annotation
for paranoid_entry() and adding an unwind hint, which effectively
silences the warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kbuild-all@01.org Cc: tipbuild@zytor.com Fixes: f09d160992d1 ("x86/entry/64: Get rid of the ALLOC_PT_GPREGS_ON_STACK and SAVE_AND_CLEAR_REGS macros") Link: http://lkml.kernel.org/r/20180212174503.5acbymg5z6p32snu@treble Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log