Fix the following warning in MIPS allmodconfig by adding a
MODULE_LICENSE() at the end of rtc-goldfish.c, based on the file header
comment which says GNU General Public License version 2:
WARNING: modpost: missing MODULE_LICENSE() in drivers/rtc/rtc-goldfish.o
The shifting of buf[5] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. If
the top bit of buf[5] is set then all then all the upper bits sec
end up as also being set because of the sign-extension. Fix this by
casting buf[5] to an unsigned long before the shift.
Detected by CoverityScan, CID#1465292 ("Unintended sign extension")
Fixes: 0e1492330cd2 ("rtc: add rtc-tx4939 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also, there is another possible race condition. The probe function is not
allowed to fail after the RTC is registered because the following may
happen:
On 32bit platforms, time_t is still a signed 32bit long. If it is
overflowed, userspace and the kernel cant agree on the current system time.
This causes multiple issues, in particular with systemd:
https://github.com/systemd/systemd/issues/1143
A good workaround is to simply avoid using hctosys which is something I
greatly encourage as the time is better set by userspace.
However, many distribution enable it and use systemd which is rendering the
system unusable in case the RTC holds a date after 2038 (and more so after
2106). Many drivers have workaround for this case and they should be
eliminated so there is only one place left to fix when userspace is able to
cope with dates after the 31bit overflow.
commit 179a502f8c46 ("rtc: snvs: add Freescale rtc-snvs driver") introduces
the SNVS RTC driver with a function snvs_rtc_enable().
snvs_rtc_enable() can return an error on the enable path however this
driver does not currently trap that failure on the probe() path and
consequently if enabling the RTC fails we encounter a later error spinning
forever in rtc_write_sync_lp().
[ 36.093481] [<c010d630>] (__irq_svc) from [<c0c2e9ec>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 36.102122] [<c0c2e9ec>] (_raw_spin_unlock_irqrestore) from [<c072e32c>] (regmap_read+0x4c/0x5c)
[ 36.110938] [<c072e32c>] (regmap_read) from [<c085d0f4>] (rtc_write_sync_lp+0x6c/0x98)
[ 36.118881] [<c085d0f4>] (rtc_write_sync_lp) from [<c085d160>] (snvs_rtc_alarm_irq_enable+0x40/0x4c)
[ 36.128041] [<c085d160>] (snvs_rtc_alarm_irq_enable) from [<c08567b4>] (rtc_timer_do_work+0xd8/0x1a8)
[ 36.137291] [<c08567b4>] (rtc_timer_do_work) from [<c01441b8>] (process_one_work+0x28c/0x76c)
[ 36.145840] [<c01441b8>] (process_one_work) from [<c01446cc>] (worker_thread+0x34/0x58c)
[ 36.153961] [<c01446cc>] (worker_thread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.161388] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
[ 36.168635] rcu_sched kthread starved for 2602 jiffies! g496 c495 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=0
[ 36.178564] rcu_sched R running task 0 8 2 0x00000000
[ 36.185664] [<c0c288b0>] (__schedule) from [<c0c29134>] (schedule+0x3c/0xa0)
[ 36.192739] [<c0c29134>] (schedule) from [<c0c2db80>] (schedule_timeout+0x78/0x4e0)
[ 36.200422] [<c0c2db80>] (schedule_timeout) from [<c01a7ab0>] (rcu_gp_kthread+0x648/0x1864)
[ 36.208800] [<c01a7ab0>] (rcu_gp_kthread) from [<c014aee4>] (kthread+0x138/0x150)
[ 36.216309] [<c014aee4>] (kthread) from [<c0107e14>] (ret_from_fork+0x14/0x20)
This patch fixes by parsing the result of rtc_write_sync_lp() and
propagating both in the probe and elsewhere. If the RTC doesn't start we
don't proceed loading the driver and don't get into this loop mess later
on.
Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d896d77 ("serial: altera_uart:
add earlycon support").
Fixes: 2780ad42f5fe ("tty: serial: altera_uart: Use port->regshift to store bus shift") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes missing characters on kernel console at low baud rates (i.e.9600).
The driver should poll TX_RDY or TX_FIFO_EMP instead of TX_EMP to ensure
that the transmitter holding register (THR) is ready to receive a new byte.
TX_EMP tells us when it is possible to send a break sequence via
SND_BRK_SEQ. While this also indicates that both the THR and the TSR are
empty, it does not guarantee that a new byte can be written just yet.
Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port") Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Gabriel Matni <gabriel.matni@exfo.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently an out of range dev->nr is detected by just reporting the
issue and later on an out-of-bounds read on array card occurs because
of this. Fix this by checking the upper range of dev->nr with the size
of array card (removes the hard coded size), move this check earlier
and also exit with the error -ENOSYS to avoid the later out-of-bounds
array read.
Detected by CoverityScan, CID#711191 ("Out-of-bounds-read")
Fixes: commit 02b20b0b4cde ("V4L/DVB (12730): Add conexant cx25821 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: %ld -> %zd] Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vivid driver has two custom controls that change the behavior of RDS.
Depending on the control setting the V4L2_CAP_READWRITE capability is toggled.
However, after an earlier commit the capability was no longer set correctly.
This is now fixed.
Fixes: 9765a32cd8 ("vivid: set device_caps in video_device") Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes vb2_vmalloc_get_userptr() to ioremap correct area.
Since the current code does ioremap the page address, if the offset > 0,
it does not do ioremap the last page and results in kernel panic.
This fixes to pass the size + offset to ioremap so that ioremap
can map correct area. Also, this uses __pfn_to_phys() to get the physical
address of given PFN.
The ADV748x handles interlaced media using V4L2_FIELD_ALTERNATE field
types. The correct specification for the height on the mbus is the
image height, in this instance, the field height.
The AFE component already correctly adjusts the height on the mbus, but
the HDMI component got left behind.
Adjust the mbus height to correctly describe the image height of the
fields when processing interlaced video for HDMI pipelines.
Make sure we don't accept more inputs than the hardware can handle. This
is a temporary fix to avoid display stall, we need to instead allocate
the BRU or BRS to display pipelines dynamically based on the number of
planes they each use.
Both lgdt33606a_release and lgdt3306a_remove kfree state, but _release is
called first, then _remove operates on states members before kfree'ing it.
This can lead to random oops/GPF/etc on USB disconnect.
While experimenting with older compiler versions, I ran
into a warning that no longer shows up on gcc-4.8 or newer:
drivers/media/platform/s3c-camif/camif-capture.c: In function '__camif_subdev_try_format':
drivers/media/platform/s3c-camif/camif-capture.c:1265:25: error: array subscript is below array bounds
This is an off-by-one bug, leading to an access before the start of the
array, while newer compilers silently assume this undefined behavior
cannot happen and leave the loop at index 0 if no other entry matches.
As Sylvester explains, we actually need to ensure that the
value is within the range, so this reworks the loop to be
easier to parse correctly, and an additional check to fall
back on the first format value for any unexpected input.
I found an existing gcc bug for it and added a reduced version
of the function there.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69249#c3 Fixes: babde1c243b2 ("[media] V4L: Add driver for S3C24XX/S3C64XX SoC series camera interface") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
The device node obtained with of_graph_get_next_endpoint() should be
released by calling of_node_put(). But it was not released when
v4l2_fwnode_endpoint_parse() failed.
This change moves the of_node_put() call before the error check and
fixes the issue.
The fixed_pll also has a fractional part. On axg s400 board, without
this parameter, the calculated rate is off by ~8Mhz (0,4%). The fixed_pll
being the root of the peripheral clock tree, this error is propagated to
the rest of the clocks
Adding the definition of the parameter fixes the problem
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
If the RCLK mux clock configuration is specified in DT and no set_sysclk()
callback is used in the sound card driver the sclk_srcrate field will remain
set to 0, leading to an incorrect PSR divider setting.
To fix this the frequency value is retrieved from the CLK_I2S_RCLK_SRC clock,
so the actual RCLK mux selection is taken into account.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the change required to create the TLV data
for dapm widget kcontrols from topology. This also fixes the following
TLV read error shown in amixer while showing the card control contents.
"amixer: Control hw:1 element TLV read error: No such device or address"
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver controls when the hardware sends completions that communicate
consumption of elements from the WQ. This is done by setting a WQEC bit
on a WQE.
The current driver sets it on every Nth WQE posting. However, the driver
isn't clearing the bit if the WQE is reused. Thus, if the queue depth
isn't evenly divisible by N, with enough time, it can be set on every
element, creating a lot of overhead and risking CQ full conditions.
Correct by clearing the bit when not setting it on an Nth element.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A stress test repeatedly resetting the adapter while performing io would
eventually report I/O failures and missing nvme namespaces.
The driver was setting the nvmefc_fcp_req->private pointer to NULL
during the IO completion routine before upcalling done(). If the
transport was also running an abort for that IO, the driver would fail
the abort with message 6140. Failing the abort is not allowed by the
nvme-fc transport, as it mandates that the io must be returned back to
the transport. As that does not happen, the transport controller delete
has an outstanding reference and can't complete teardown.
The NULL-ing of the private pointer should be done only when the io is
considered complete. It's complete when the adapter returns the exchange
with the "exchange busy" flag clear.
Move the NULL'ing of the structure to the done case. This leaves the io
contexts set while it is busy and until the subsequent XRI_ABORTED
completion which returns the exchange is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was simultaneously setting a combination of flags that caused
lpfc_do_work()to effectively spin between slow path work and new event
data, causing the lockup.
Ensure in the typical wq completions, that new event data flags are set
if the slow path flag is running. The slow path will eventually
reschedule the wq handling.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a test that is doing large numbers of cable swaps on the target, the
nvme controllers wouldn't reconnect.
During the cable swaps, the targets n_port_id would change. This
information was passed to the nvme-fc transport, in the new remoteport
registration. However, the nvme-fc transport didn't update the n_port_id
value in the remoteport struct when it reused an existing structure.
Later, when a new association was attempted on the remoteport, the
driver's NVME LS routine would use the stale n_port_id from the
remoteport struct to address the LS. As the device is no longer at that
address, the LS would go into never never land.
Separately, the nvme-fc transport will be corrected to update the
n_port_id value on a re-registration.
However, for now, there's no reason to use the transports values. The
private pointer points to the drivers node structure and the node
structure is up to date. Therefore, revise the LS routine to use the
drivers data structures for the LS. Augmented the debug message for
better debugging in the future.
Also removed a duplicate if check that seems to have slipped in.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver ignored checks on whether the link should be kept
administratively down after a link bounce. Correct the checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI PRE-FETCH (10 or 16) command is present both on hard disks
and some SSDs. It is useful when the address of the next block(s) to
be read is known but it is not following the LBA of the current READ
(so read-ahead won't help). It returns two "good" SCSI Status values.
If the requested blocks have fitted (or will most likely fit (when
the IMMED bit is set)) into the disk's cache, it returns CONDITION
MET. If it didn't (or will not) fit then it returns GOOD status.
The goal of this patch is to stop the SCSI subsystem treating the
CONDITION MET SCSI status as an error. The current state makes the
PRE-FETCH command effectively unusable via pass-throughs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"The DISK-SUBSYSTEM is a special model name returned when LUs
are not installed. For example, when LU#0 is not installed in "OPEN-"
models, LU#0 is detected as the DISK-SUBSYSTEM model":
https://marc.info/?l=linux-scsi&m=125424006417825
If a recursive IOP_RESET is invoked, usually due to the eh_thread
handling errors after the first reset, be sure we flag that the command
thread has been stopped to avoid an Oops of the form;
When exiting a transformation, the cra_exit() helper is called in each
driver providing one. The Inside Secure SafeXcel driver has one, which
is responsible of freeing some areas and of sending one invalidation
request to the crypto engine, to invalidate the context that was used
during the transformation.
We could see in some setups (when lots of transformations were being
used with a short lifetime, and hence lots of cra_exit() calls) NULL
pointer dereferences and other weird issues. All these issues were
coming from accessing the tfm context.
The issue is the invalidation request completion is checked using a
wait_for_completion_interruptible() call in both the cipher and hash
cra_exit() helpers. In some cases this was interrupted while the
invalidation request wasn't processed yet. And then cra_exit() returned,
and its caller was freeing the tfm instance. Only then the request was
being handled by the SafeXcel driver, which lead to the said issues.
This patch fixes this by using wait_for_completion() calls in these
specific cases.
This patch fixes the Inside Secure SafeXcel driver not to overwrite the
interrupt threshold value. In certain cases the value of this register,
which controls when to fire an interrupt, was overwritten. This lead to
packet not being processed or acked as the driver never was aware of
their completion.
This patch fixes this behaviour by not setting the threshold when
requests are being processed by the engine.
Fixes: dc7e28a3286e ("crypto: inside-secure - dequeue all requests at once") Suggested-by: Ofer Heifetz <oferh@marvell.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the extra cache computation when the queued data is a
multiple of a block size. This fixes the hash support in some cases.
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the cache length computation as cache_len could end up
being a negative value. The check between the queued size and the
block size is updated to reflect the caching mechanism which can cache
up to a full block size (included!).
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check in the SafeXcel dequeue function, to avoid
processing request further if no hardware command was issued. This can
happen in certain cases where the ->send() function caches all the data
that would have been send.
Fixes: 809778e02cd4 ("crypto: inside-secure - fix hash when length is a multiple of a block") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I don't why we need take a single write lock and disable interrupts
while setting up debugfs. This is what what happens when we try anyway:
|ccp 0000:03:00.2: enabling device (0000 -> 0002)
|BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:69
|in_atomic(): 1, irqs_disabled(): 1, pid: 3, name: kworker/0:0
|irq event stamp: 17150
|hardirqs last enabled at (17149): [<0000000097a18c49>] restore_regs_and_return_to_kernel+0x0/0x23
|hardirqs last disabled at (17150): [<000000000773b3a9>] _raw_write_lock_irqsave+0x1b/0x50
|softirqs last enabled at (17148): [<0000000064d56155>] __do_softirq+0x3b8/0x4c1
|softirqs last disabled at (17125): [<0000000092633c18>] irq_exit+0xb1/0xc0
|CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.16.0-rc2+ #30
|Workqueue: events work_for_cpu_fn
|Call Trace:
| dump_stack+0x7d/0xb6
| ___might_sleep+0x1eb/0x250
| down_write+0x17/0x60
| start_creating+0x4c/0xe0
| debugfs_create_dir+0x9/0x100
| ccp5_debugfs_setup+0x191/0x1b0
| ccp5_init+0x8a7/0x8c0
| ccp_dev_init+0xb8/0xe0
| sp_init+0x6c/0x90
| sp_pci_probe+0x26e/0x590
| local_pci_probe+0x3f/0x90
| work_for_cpu_fn+0x11/0x20
| process_one_work+0x1ff/0x650
| worker_thread+0x1d4/0x3a0
| kthread+0xfe/0x130
| ret_from_fork+0x27/0x50
If any locking is required, a simple mutex will do it.
Cc: Gary R Hook <gary.hook@amd.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Atmel AES driver uses memzero_explicit on the keys on error, but the
variable zeroed isn't the right one because of a typo. Fix this by using
the right variable.
Fixes: 89a82ef87e01 ("crypto: atmel-authenc - add support to authenc(hmac(shaX), Y(aes)) modes") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the safexcel_hmac_init_pad() function to also wait
for completion when the digest return code is -EBUSY, as it would mean
the request is in the backlog to be processed later.
This patches moves the digest information from the transformation
context to the request context. This fixes cases where HMAC init
functions were called and override the digest value for a short period
of time, as the HMAC init functions call the SHA init one which reset
the value. This lead to a small percentage of HMAC being incorrectly
computed under heavy load.
Fixes: 1b44c5a60c13 ("crypto: inside-secure - add SafeXcel EIP197 crypto engine driver") Suggested-by: Ofer Heifetz <oferh@marvell.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Ofer here did all the work, from seeing the issue to understanding the
root cause. I only made the patch.] Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8f18c8a48b73 ("staging: lustre: lmv: separate master object
with master stripe") changed how lmo_root inodes were managed,
particularly when LMV_HASH_FLAG_MIGRATION is not set.
Previously lsm_md_oinfo[0].lmo_root was always a borrowed
inode reference and didn't need to by iput().
Since the change, that special case only applies when
LMV_HASH_FLAG_MIGRATION is set
In the upstream (lustre-release) version of this patch [Commit 60e07b972114 ("LU-4690 lod: separate master object with master
stripe")] the for loop in the lmv_unpack_md() was changed to count
from 0 and to ignore entry 0 if LMV_HASH_FLAG_MIGRATION is set.
In the patch that got applied to Linux, that change was missing,
so lsm_md_oinfo[0].lmo_root is never iput().
This results in a "VFS: Busy inodes" warning at unmount.
Fixes: 8f18c8a48b73 ("staging: lustre: lmv: separate master object with master stripe") Signed-off-by: NeilBrown <neilb@suse.com> Reviewed-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The case statement in get_ap_information() should not use literal integers
to parse information element IDs when these values are provided by name
in 'enum ieee80211_eid' in the header 'linux/ieee80211.h'.
Currently the allocation of priv->oldaddr is not null checked which will
lead to subsequent errors when accessing priv->oldaddr. Fix this with
a null pointer check and a return of -ENOMEM on allocation failure.
Detected with Coccinelle:
drivers/staging/rtl8192u/r8192U_core.c:1708:2-15: alloc with no test,
possible model on line 1723
Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use netdev_alloc_frag() instead of kmalloc to allocate space for
the S/G table of egress multi-buffer frames.
This fixes a bug where an unaligned pointer received from the
allocator would be overwritten with the 64B aligned value,
leading to a wrong address being later passed to kfree.
syzbot is reporting crashes after memory allocation failure inside
do_kexec_load() [1]. This is because free_transition_pgtable() is called
by both init_transition_pgtable() and machine_kexec_cleanup() when memory
allocation failed inside init_transition_pgtable().
Regarding 32bit code, machine_kexec_free_page_tables() is called by both
machine_kexec_alloc_page_tables() and machine_kexec_cleanup() when memory
allocation failed inside machine_kexec_alloc_page_tables().
Fix this by leaving the error handling to machine_kexec_cleanup()
(and optionally setting NULL after free_page()).
syzbot is reporting ODEBUG messages at hfsplus_fill_super() [1]. This
is because hfsplus_fill_super() forgot to call cancel_delayed_work_sync().
As far as I can see, it is hfsplus_mark_mdb_dirty() from
hfsplus_new_inode() in hfsplus_fill_super() that calls
queue_delayed_work(). Therefore, I assume that hfsplus_new_inode() does
not fail if queue_delayed_work() was called, and the out_put_hidden_dir
label is the appropriate location to call cancel_delayed_work_sync().
There's currently no limit on wiphy names, other than netlink
message size and memory limitations, but that causes issues when,
for example, the wiphy name is used in a uevent, e.g. in rfkill
where we use the same name for the rfkill instance, and then the
buffer there is "only" 2k for the environment variables.
This was reported by syzkaller, which used a 4k name.
Limit the name to something reasonable, I randomly picked 128.
Reported-by: syzbot+230d9e642a85d3fec29c@syzkaller.appspotmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2d1d4c1e591f made loop_get_status() drop lo_ctx_mutex before
returning, but the loop_get_status_old(), loop_get_status64(), and
loop_get_status_compat() wrappers don't call loop_get_status() if the
passed argument is NULL. The callers expect that the lock is dropped, so
make sure we drop it in that case, too.
We hit an issue where a loop device on NFS was stuck in
loop_get_status() doing vfs_getattr() after the NFS server died, which
caused a pile-up of uninterruptible processes waiting on lo_ctl_mutex.
There's no reason to hold this lock while we wait on the filesystem;
let's drop it so that other processes can do their thing. We need to
grab a reference on lo_backing_file while we use it, and we can get rid
of the check on lo_device, which has been unnecessary since commit a34c0ae9ebd6 ("[PATCH] loop: remove the bio remapping capability") in
the linux-history tree.
The Intel Bluetooth device 22560 family (HarrisonPeak, QnJ, and IcyPeak)
use the same firmware loading mechanism as previous generation,
so include new USB product ID and whitelist the hardware variant.
Hauppauge em28xx bulk devices exhibit continuity errors and corrupted
packets, when run in VMWare virtual machines. Unknown if other
manufacturers bulk models exhibit the same issue. KVM/Qemu is unaffected.
According to documentation the maximum packet multiplier for em28xx in bulk
transfer mode is 256 * 188 bytes. This changes the size of bulk transfers
to maximum supported value and have a bonus beneficial alignment.
Before:
After:
This sets up USB to expect just as many bytes as the em28xx is set to emit.
Successful usage under load afterwards natively and in both VMWare
and KVM/Qemu virtual machines.
Signed-off-by: Brad Love <brad@nextdimension.cc> Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When used as an i2c device there is a module usage count mismatch on
removal, preventing the driver from being used thereafter. dvb_attach
increments the usage count so it is properly balanced on removal.
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a AIO read() operation on the function FS gadget driver a URB is
submitted asynchronously and on URB completion the received data is copied
to the userspace buffer associated with the read operation.
This is done from a kernel worker thread invoking copy_to_user() (through
copy_to_iter()). And while the user space process memory is made available
to the kernel thread using use_mm(), some architecture require in addition
to this that the operation runs with USER_DS set. Otherwise the userspace
memory access will fail.
For example on ARM64 with Privileged Access Never (PAN) and User Access
Override (UAO) enabled the following crash occurs.
Internal error: Accessing user space memory with fs=KERNEL_DS: 9600004f [#1] SMP
Modules linked in:
CPU: 2 PID: 1636 Comm: kworker/2:1 Not tainted 4.9.0-04081-g8ab2dfb-dirty #487
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
Workqueue: events ffs_user_copy_worker
task: ffffffc87afc8080 task.stack: ffffffc87a00c000
PC is at __arch_copy_to_user+0x190/0x220
LR is at copy_to_iter+0x78/0x3c8
[...]
[<ffffff800847b790>] __arch_copy_to_user+0x190/0x220
[<ffffff80086f25d8>] ffs_user_copy_worker+0x70/0x130
[<ffffff80080b8c64>] process_one_work+0x1dc/0x460
[<ffffff80080b8f38>] worker_thread+0x50/0x4b0
[<ffffff80080bf5a0>] kthread+0xd8/0xf0
[<ffffff8008083680>] ret_from_fork+0x10/0x50
Address this by placing a set_fs(USER_DS) before of the copy operation
and revert it again once the copy operation has finished.
This patch is analogous to commit d7ffde35e31a ("vhost: use USER_DS in
vhost_worker thread") which addresses the same underlying issue.
Some UDC drivers (like the DWC3) expect that the response to a setup()
request is queued from within the setup function itself so that it is
available as soon as setup() has completed.
Upon receiving a setup request the function fs driver creates an event that
is made available to userspace. And only once userspace has acknowledged
that event the response to the setup request is queued.
So it violates the requirement of those UDC drivers and random failures can
be observed. This is basically a race condition and if userspace is able to
read the event and queue the response fast enough all is good. But if it is
not, for example because other processes are currently scheduled to run,
the USB host that sent the setup request will observe an error.
To avoid this the gadget framework provides the USB_GADGET_DELAYED_STATUS
return code. If a setup() callback returns this value the UDC driver is
aware that response is not yet available and can uses the appropriate
methods to handle this case.
Since in the case of function fs the response will never be available when
the setup() function returns make sure that this status code is used.
This fixed random occasional failures that were previously observed on a
DWC3 based system under high system load.
Added missing GUSBCFG programming in host mode, which fixes
transaction errors issue on HiKey and Altera Cyclone V boards.
These field even if was programmed in device mode (in function
dwc2_hsotg_core_init_disconnected()) will be resetting to POR values
after core soft reset applied.
So, each time when switching to host mode required to set this field
to correct value.
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST
bit is cleared, we must wait at least 50ms before accessing the PHY
domain (synchronization delay).
Add native DSD support quirk for Luxman DA-06 DAC, by adding the
PID/VID 1852:5065.
Rename "is_marantz_denon_dac()" function to "is_itf_usb_dsd_2alts_dac()"
to cover broader device family sharing the same USB audio
implementation(*).
For the same reason, rename "is_teac_dsd_dac()" function to
"is_itf_usb_dsd_3alts_dac()".
(*)
These devices have the same USB controller "ITF-USB DSD", supplied by
INTERFACE Co., Ltd.
"ITF-USB DSD" USB controller has two patterns,
Pattern 1. (2 altsets version)
- Altset 0: for control
- Altset 1: for stream (S32)
- Altset 2: for stream (S32, DSD_U32)
Pattern 2. (3 altsets version)
- Altset 0: for control
- Altset 1: for stream (S16)
- Altset 2: for stream (S32)
- Altset 3: for stream (S32, DSD_U32)
"is_itf_usb_dsd_2alts_dac()" returns true, if the DAC has "Pattern 1"
USB controller, and "is_itf_usb_dsd_3alts_dac()" returns true, if
"Pattern2".
zfcp_erp_adapter_reopen() schedules blocking of all of the adapter's
rports via zfcp_scsi_schedule_rports_block() and enqueues a reopen
adapter ERP action via zfcp_erp_action_enqueue(). Both are separately
processed asynchronously and concurrently.
Blocking of rports is done in a kworker by zfcp_scsi_rport_work(). It
calls zfcp_scsi_rport_block(), which then traces a DBF REC "scpdely" via
zfcp_dbf_rec_trig(). zfcp_dbf_rec_trig() acquires the DBF REC spin lock
and then iterates with list_for_each() over the adapter's ERP ready list
without holding the ERP lock. This opens a race window in which the
current list entry can be moved to another list, causing list_for_each()
to iterate forever on the wrong list, as the erp_ready_head is never
encountered as terminal condition.
Meanwhile the ERP action can be processed in the ERP thread by
zfcp_erp_thread(). It calls zfcp_erp_strategy(), which acquires the ERP
lock and then calls zfcp_erp_action_to_running() to move the ERP action
from the ready to the running list. zfcp_erp_action_to_running() can
move the ERP action using list_move() just during the aforementioned
race window. It then traces a REC RUN "erator1" via zfcp_dbf_rec_run().
zfcp_dbf_rec_run() tries to acquire the DBF REC spin lock. If this is
held by the infinitely looping kworker, it effectively spins forever.
Any adapter recovery can trigger this, such as setting the device offline
or reboot.
V4.9 commit 4eeaa4f3f1d6 ("zfcp: close window with unblocked rport
during rport gone") introduced additional tracing of (un)blocking of
rports. It missed that the adapter->erp_lock must be held when calling
zfcp_dbf_rec_trig().
This fix uses the approach formerly introduced by commit aa0fec62391c
("[SCSI] zfcp: Fix sparse warning by providing new entry in dbf") that got
later removed by commit ae0904f60fab ("[SCSI] zfcp: Redesign of the debug
tracing for recovery actions.").
Introduce zfcp_dbf_rec_trig_lock(), a wrapper for zfcp_dbf_rec_trig() that
acquires and releases the adapter->erp_lock for read.
Reported-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Jens Remus <jremus@linux.ibm.com> Fixes: 4eeaa4f3f1d6 ("zfcp: close window with unblocked rport during rport gone") Cc: <stable@vger.kernel.org> # 2.6.32+ Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This shall help avoid copying uninitialized memory to the userspace when
calling ioctl(fd, SG_IO) with an empty command.
Reported-by: syzbot+7d26fc1eea198488deab@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BPF JIT need safe guarding against spectre v2 in the sk_load_xxx
assembler stubs and the indirect branches generated by the JIT itself
need to be converted to expolines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>