Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.
This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C
Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #11350 [hci0] 84680.231216
Address: 56:BC:E8:24:11:68 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #11351 [hci0] 84680.246022
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #11352 [hci0] 84680.246417
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #11353 [hci0] 84680.248854
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11354 [hci0] 84680.249466
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #11355 [hci0] 84680.253222
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #11356 [hci0] 84680.458387
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11357 [hci0] 84680.458737
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #11358 [hci0] 84680.469982
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #11359 [hci0] 84680.470444
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #11360 [hci0] 84680.474971
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4 #11362 [hci0] 84682.551014
LE Create Connection Cancel (0x08|0x000e) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #11363 [hci0] 84682.551074
LE Connection Complete (0x01)
Status: Unknown Connection Identifier (0x02)
Handle: 0
Role: Master (0x00)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Connection interval: 0.00 msec (0x0000)
Connection latency: 0 (0x0000)
Supervision timeout: 0 msec (0x0000)
Master clock accuracy: 0x00
After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #210 [hci0] 667.152459
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #211 [hci0] 667.153613
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #212 [hci0] 667.153704
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #213 [hci0] 667.154584
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #214 [hci0] 667.182619
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #215 [hci0] 667.182704
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #216 [hci0] 667.183599
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #217 [hci0] 667.183645
Address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #218 [hci0] 667.184590
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #219 [hci0] 667.184613
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #220 [hci0] 667.186558
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #221 [hci0] 667.485824
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 0
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13 {0x0002} [hci0] 667.485996
LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
Flags: 0x00000000
Data length: 0
Patch series "mm/get_user_pages_fast fixes, cleanups", v2.
Turns out get_user_pages_fast and __get_user_pages_fast return different
values on error when given a single page: __get_user_pages_fast returns
0. get_user_pages_fast returns either 0 or an error.
Callers of get_user_pages_fast expect an error so fix it up to return an
error consistently.
Stress the difference between get_user_pages_fast and
__get_user_pages_fast to make sure callers aren't confused.
This patch (of 3):
__gup_benchmark_ioctl does not handle the case where get_user_pages_fast
fails:
- a negative return code will cause a buffer overrun
- returning with partial success will cause use of uninitialized
memory.
[akpm@linux-foundation.org: simplification] Link: http://lkml.kernel.org/r/1522962072-182137-3-git-send-email-mst@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_user_pages_fast is supposed to be a faster drop-in equivalent of
get_user_pages. As such, callers expect it to return a negative return
code when passed an invalid address, and never expect it to return 0
when passed a positive number of pages, since its documentation says:
* Returns number of pages pinned. This may be fewer than the number
* requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno.
When get_user_pages_fast fall back on get_user_pages this is exactly
what happens. Unfortunately the implementation is inconsistent: it
returns 0 if passed a kernel address, confusing callers: for example,
the following is pretty common but does not appear to do the right thing
with a kernel address:
ret = get_user_pages_fast(addr, 1, writeable, &page);
if (ret < 0)
return ret;
Change get_user_pages_fast to return -EFAULT when supplied a kernel
address to make it match expectations.
All callers have been audited for consistency with the documented
semantics.
Link: http://lkml.kernel.org/r/1522962072-182137-4-git-send-email-mst@redhat.com Fixes: 5b65c4677a57 ("mm, x86/mm: Fix performance regression in get_user_pages_fast()") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Git commit c60a03fee0e5 ("s390: switch to {get,put}_compat_sigset()")
contains a typo and now copies the wrong pointer to user space.
Use the correct pointer instead.
Reported-and-tested-by: Stefan Liebler <stli@linux.vnet.ibm.com> Fixes: c60a03fee0e5 ("s390: switch to {get,put}_compat_sigset()") Cc: <stable@vger.kernel.org> # v4.15+ Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On an Output queue, both EMPTY and PENDING buffer states imply that the
buffer is ready for completion-processing by the upper-layer drivers.
So for a non-QEBSM Output queue, get_buf_states() merges mixed
batches of PENDING and EMPTY buffers into one large batch of EMPTY
buffers. The upper-layer driver (ie. qeth) later distuingishes PENDING
from EMPTY by inspecting the slsb_state for
QDIO_OUTBUF_STATE_FLAG_PENDING.
But the merge logic in get_buf_states() contains a bug that causes us to
erronously also merge ERROR buffers into such a batch of EMPTY buffers
(ERROR is 0xaf, EMPTY is 0xa1; so ERROR & EMPTY == EMPTY).
Effectively, most outbound ERROR buffers are currently discarded
silently and processed as if they had succeeded.
Note that this affects _all_ non-QEBSM device types, not just IQD with CQ.
Fix it by explicitly spelling out the exact conditions for merging.
For extracting the "get initial state" part out of the loop, this relies
on the fact that get_buf_states() is never called with a count of 0. The
QEBSM path already strictly requires this, and the two callers with
variable 'count' make sure of it.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Cc: <stable@vger.kernel.org> #v3.2+ Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate retry of EQBS after CCQ 96 means that we potentially misreport
the state of buffers inspected during the first EQBS call.
This occurs when
1. the first EQBS finds all inspected buffers still in the initial state
set by the driver (ie INPUT EMPTY or OUTPUT PRIMED),
2. the EQBS terminates early with CCQ 96, and
3. by the time that the second EQBS comes around, the state of those
previously inspected buffers has changed.
If the state reported by the second EQBS is 'driver-owned', all we know
is that the previous buffers are driver-owned now as well. But we can't
tell if they all have the same state. So for instance
- the second EQBS reports OUTPUT EMPTY, but any number of the previous
buffers could be OUTPUT ERROR by now,
- the second EQBS reports OUTPUT ERROR, but any number of the previous
buffers could be OUTPUT EMPTY by now.
Effectively, this can result in both over- and underreporting of errors.
If the state reported by the second EQBS is 'HW-owned', that doesn't
guarantee that the previous buffers have not been switched to
driver-owned in the mean time. So for instance
- the second EQBS reports INPUT EMPTY, but any number of the previous
buffers could be INPUT PRIMED (or INPUT ERROR) by now.
This would result in failure to process pending work on the queue. If
it's the final check before yielding initiative, this can cause
a (temporary) queue stall due to IRQ avoidance.
Fixes: 25f269f17316 ("[S390] qdio: EQBS retry after CCQ 96") Cc: <stable@vger.kernel.org> #v3.2+ Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf03c00e7c1 "nfit: scrub and register regions in a workqueue"
mistakenly attempts to register a region per BLK aperture. There is
nothing to register for individual apertures as they belong as a set to
a BLK aperture group that are registered with a corresponding
DIMM-control-region. Filter them for registration to prevent some
needless devm_kzalloc() allocations.
Cc: <stable@vger.kernel.org> Fixes: 1cf03c00e7c1 ("nfit: scrub and register regions in a workqueue") Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ 92.931922] 1 lock held by systemd-udevd/525:
[ 92.933642] #0: 00000000a2849e25 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x73/0x4f0
----------------------------------------
The reason of deadlock turned out that wait_event_interruptible() in
blk_queue_enter() got stuck with bdev->bd_mutex held at __blkdev_put()
due to q->mq_freeze_depth == 1.
[ 92.943530] 1 lock held by a.out/634:
[ 92.945105] #0: 00000000a2849e25 (&bdev->bd_mutex){+.+.}, at: __blkdev_put+0x3c/0x1e0
----------------------------------------
The reason of q->mq_freeze_depth == 1 turned out that loop_set_status()
forgot to call blk_mq_unfreeze_queue() at error paths for
info->lo_encrypt_type != NULL case.
Resource auditing is using the peer field which is not available
when the rlim data struct is used, because it is a different element
of the same union. Accessing peer during resource auditing could
cause garbage log entries or even oops the kernel.
Move the rlim data block into the same struct as the peer field
so they can be used together.
CC: <stable@vger.kernel.org> Fixes: 86b92cb782b3 ("apparmor: move resource checks to using labels") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .ns_name should not be virtualized by the current ns view. It
needs to report the ns base name as that is being used during startup
as part of determining apparmor policy namespace support.
The existence test is not being properly logged as the signal mapping
maps it to the last entry in the named signal table. This is done
to help catch bugs by making the 0 mapped signal value invalid so
that we can catch the signal value not being filled in.
When fixing the off-by-one comparision logic the reporting of the
existence test was broken, because the logic behind the mapped named
table was hidden. Fix this by adding a define for the name lookup
and using it.
Cc: Stable <stable@vger.kernel.org> Fixes: f7dc4c9a855a1 ("apparmor: fix off-by-one comparison on MAXMAPPED_SIG") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The description of commit e39a97353e53 is wrong: it mentions that commit 2a842acab109 introduced a bug in __scsi_error_from_host_byte() although that
commit did not change the behavior of that function. Additionally, commit e39a97353e53 introduced a bug: it causes commands that fail with
hostbyte=DID_OK and driverbyte=DRIVER_SENSE to be completed with
BLK_STS_OK. Hence revert that commit.
Fixes: e39a97353e53 ("scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()") Reported-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Damien Le Moal <damien.lemoal@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lee Duncan <lduncan@suse.com> Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that fixes the crashes in the following commit introduced a small
memory leak:
commit 6a2cf8d3663e ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure")
Fixing this requires a bit of reworking, which I've explained. Also provide
some code cleanup.
There is a small window in qla2x00_probe_one where if qla2x00_alloc_queues
fails, we end up never freeing req and rsp and leak 0xc0 and 0xc8 bytes
respectively (the sizes of req and rsp).
I originally put in checks to test for this condition which were based on
the incorrect assumption that if ha->rsp_q_map and ha->req_q_map were
allocated, then rsp and req were allocated as well. This is incorrect.
There is a window between these allocations:
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
goto probe_hw_failed;
ret = qla2x00_request_irqs(ha, rsp);
goto probe_failed;
if (qla2x00_alloc_queues(ha, req, rsp)) {
goto probe_failed;
[if successful, now ha->rsp_q_map and ha->req_q_map allocated]
To simplify this, we should just set req and rsp to NULL after we free
them. Sounds simple enough? The problem is that req and rsp are pointers
defined in the qla2x00_probe_one and they are not always passed by reference
to the routines that free them.
Here are paths which can free req and rsp:
PATH 1:
qla2x00_probe_one
ret = qla2x00_mem_alloc(ha, req_length, rsp_length, &req, &rsp);
[req and rsp are passed by reference, but if this fails, we currently
do not NULL out req and rsp. Easily fixed]
PATH 2:
qla2x00_probe_one
failing in qla2x00_request_irqs or qla2x00_alloc_queues
probe_failed:
qla2x00_free_device(base_vha);
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 3:
qla2x00_probe_one:
failing in qla2x00_mem_alloc or qla2x00_create_host
probe_hw_failed:
qla2x00_free_req_que(ha, req)
qla2x00_free_rsp_que(ha, rsp)
PATH 1: This should currently work, but it doesn't because rsp and rsp are
not set to NULL in qla2x00_mem_alloc. Easily remedied.
PATH 2: req and rsp aren't passed in at all to qla2x00_free_device but are
derived from ha->req_q_map[0] and ha->rsp_q_map[0]. These are only set up if
qla2x00_alloc_queues succeeds.
In qla2x00_free_queues, we are protected from crashing if these don't exist
because req_qid_map and rsp_qid_map are only set on their allocation. We are
guarded in this way:
for (cnt = 0; cnt < ha->max_req_queues; cnt++) {
if (!test_bit(cnt, ha->req_qid_map))
continue;
PATH 3: This works. We haven't freed req or rsp yet (or they were never
allocated if qla2x00_mem_alloc failed), so we'll attempt to free them here.
To summarize, there are a few small changes to make this work correctly and
(and for some cleanup):
1) (For PATH 1) Set *rsp and *req to NULL in case of failure in
qla2x00_mem_alloc so these are correctly set to NULL back in
qla2x00_probe_one
2) After jumping to probe_failed: and calling qla2x00_free_device,
explicitly set rsp and req to NULL so further calls with these pointers do
not crash, i.e. the free queue calls in the probe_hw_failed section we fall
through to.
3) Fix return code check in the call to qla2x00_alloc_queues. We currently
drop the return code on the floor. The probe fails but the caller of the
probe doesn't have an error code, so it attaches to pci. This can result in
a crash on module shutdown.
4) Remove unnecessary NULL checks in qla2x00_free_req_que,
qla2x00_free_rsp_que, and the egregious NULL checks before kfrees and vfrees
in qla2x00_mem_free.
I tested this out running a scenario where the card breaks at various times
during initialization. I made sure I forced every error exit path in
qla2x00_probe_one.
Cc: <stable@vger.kernel.org> # v4.16 Fixes: 6a2cf8d3663e ("scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure") Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently scsi_dh_lookup() doesn't check for NULL as a device name. This
combined with nvme over dm-mpath results in the following messages
emitted by device-mapper:
device-mapper: multipath: Could not failover device 259:67: Handler scsi_dh_(null) error 14.
Let scsi_dh_lookup() fail fast on NULL names.
[mkp: typo fix]
Cc: <stable@vger.kernel.org> # v4.16 Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're neglecting to clear the umask after it's set, which can cause a
later unrelated rpc to (incorrectly) use the same umask if it happens to
be processed by the same thread.
There's a more subtle problem here too:
An NFSv4 compound request is decoded all in one pass before any
operations are executed.
Currently we're setting current->fs->umask at the time we decode the
compound. In theory a single compound could contain multiple creates
each setting a umask. In that case we'd end up using whichever umask
was passed in the *last* operation as the umask for all the creates,
whether that was correct or not.
So, we should just be saving the umask at decode time and waiting to set
it until we actually process the corresponding operation.
In practice it's unlikely any client would do multiple creates in a
single compound. And even if it did they'd likely be from the same
process (hence carry the same umask). So this is a little academic, but
we should get it right anyway.
Fixes: 47057abde515 (nfsd: add support for the umask attribute) Cc: stable@vger.kernel.org Reported-by: Lucash Stach <l.stach@pengutronix.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a fix for a regression in 32 bit kernels caused by an invalid
check for pgoff overflow in hugetlbfs mmap setup. The check incorrectly
specified that the size of a loff_t was the same as the size of a long.
The regression prevents mapping hugetlbfs files at offsets greater than
4GB on 32 bit kernels.
On 32 bit kernels conversion from a page based unsigned long can not
overflow a loff_t byte offset. Therefore, skip this check if
sizeof(unsigned long) != sizeof(loff_t).
Link: http://lkml.kernel.org/r/20180330145402.5053-1-mike.kravetz@oracle.com Fixes: 63489f8e8211 ("hugetlbfs: check for pgoff value overflow") Reported-by: Dan Rue <dan.rue@linaro.org> Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Tested-by: Anders Roxell <anders.roxell@linaro.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Nic Losby <blurbdust@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple
concurrent xenstore accesses") made a subtle change to the semantic of
xenbus_dev_request_and_reply() and xenbus_transaction_end().
Before on an error response to XS_TRANSACTION_END
xenbus_dev_request_and_reply() would not decrement the active
transaction counter. But xenbus_transaction_end() has always counted the
transaction as finished regardless of the response.
The new behavior is that xenbus_dev_request_and_reply() and
xenbus_transaction_end() will always count the transaction as finished
regardless the response code (handled in xs_request_exit()).
But xenbus_dev_frontend tries to end a transaction on closing of the
device if the XS_TRANSACTION_END failed before. Trying to close the
transaction twice corrupts the reference count. So fix this by also
considering a transaction closed if we have sent XS_TRANSACTION_END once
regardless of the return code.
Eddie Horng reported that readdir of an overlayfs directory that
was exported via NFSv3 returns entries with d_type set to DT_UNKNOWN.
The reason is that while preparing the response for readdirplus, nfsd
checks inside encode_entryplus_baggage() that a child dentry's inode
number matches the value of d_ino returns by overlayfs readdir iterator.
Because the overlayfs inodes use arbitrary inode numbers that are not
correlated with the values of st_ino/d_ino, NFSv3 falls back to not
encoding d_type. Although this is an allowed behavior, we can fix it for
the case of all overlayfs layers on the same underlying filesystem.
When NFS export is enabled and d_ino is consistent with st_ino
(samefs), set the same value also to i_ino in ovl_fill_inode() for all
overlayfs inodes, nfsd readdirplus sanity checks will pass.
ovl_fill_inode() may be called from ovl_new_inode(), before real inode
was created with ino arg 0. In that case, i_ino will be updated to real
upper inode i_ino on ovl_inode_init() or ovl_inode_update().
Reported-by: Eddie Horng <eddiehorng.tw@gmail.com> Tested-by: Eddie Horng <eddiehorng.tw@gmail.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Fixes: 8383f1748829 ("ovl: wire up NFS export operations") Cc: <stable@vger.kernel.org> #v4.16 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of now if we encounter an opaque dir while looking for a dentry, we set
d->last=true. This means that there is no need to look further in any of
the lower layers. This works fine as long as there are no redirets or
relative redircts. But what if there is an absolute redirect on the
children dentry of opaque directory. We still need to continue to look into
next lower layer. This patch fixes it.
Here is an example to demonstrate the issue. Say you have following setup.
upper: /redirect (redirect=/a/b/c)
lower1: /a/[b]/c ([b] is opaque) (c has absolute redirect=/a/b/d/)
lower0: /a/b/d/foo
Now "redirect" dir should merge with lower1:/a/b/c/ and lower0:/a/b/d.
Note, despite the fact lower1:/a/[b] is opaque, we need to continue to look
into lower0 because children c has an absolute redirect.
d->last signifies that this is the last layer we are looking into and there
is no more. And that means this allows for some optimzation opportunities
during lookup. For example, in ovl_lookup_single() we don't have to check
for opaque xattr of a directory is this is the last layer we are looking
into (d->last = true).
But knowing for sure whether we are looking into last layer can be very
tricky. If redirects are not enabled, then we can look at poe->numlower and
figure out if the lookup we are about to is last layer or not. But if
redircts are enabled then it is possible poe->numlower suggests that we are
looking in last layer, but there is an absolute redirect present in found
element and that redirects us to a layer in root and that means lookup will
continue in lower layers further.
In this case pure is "pure upper". When we look for "foo", that time
poe->numlower=0. But that alone does not mean that we will not search for a
merge candidate in /lowerdir. Absolute redirect changes that.
IOW, d->last should not be set just based on poe->numlower if redirects are
enabled. That can lead to setting d->last while it should not have and that
means we will not check for opaque xattr while we should have.
So do this.
- If redirects are not enabled, then continue to rely on poe->numlower
information to determine if it is last layer or not.
- If redirects are enabled, then set d->last = true only if this is the
last layer in root ovl_entry (roe).
From commit 4b855ad37194 ("blk-mq: Create hctx for each present CPU),
blk-mq doesn't remap queue after CPU topo is changed, that said when
some of these offline CPUs become online, they are still mapped to
hctx 0, then hctx 0 may become the bottleneck of IO dispatch and
completion.
This patch sets up the mapping from the beginning, and aligns to
queue mapping for PCI device (blk_mq_pci_map_queues()).
Cc: Stefan Haberland <sth@linux.vnet.ibm.com> Cc: Keith Busch <keith.busch@intel.com> Cc: stable@vger.kernel.org Fixes: 4b855ad37194 ("blk-mq: Create hctx for each present CPU) Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From commit 20e4d81393196 (blk-mq: simplify queue mapping & schedule
with each possisble CPU), one hctx can be mapped from all offline CPUs,
then hctx->next_cpu can be set as wrong.
This patch fixes this issue by making hctx->next_cpu pointing to the
first CPU in hctx->cpumask if all CPUs in hctx->cpumask are offline.
Cc: Stefan Haberland <sth@linux.vnet.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Fixes: 20e4d81393196 ("blk-mq: simplify queue mapping & schedule with each possisble CPU") Cc: stable@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch orders getting budget and driver tag by making sure to acquire
driver tag after budget is got, this way can help to avoid the following
race:
1) before dispatch request from scheduler queue, get one budget first, then
dequeue a request, call it request A.
2) in another IO path for dispatching request B which is from hctx->dispatch,
driver tag is got, then try to get budget in blk_mq_dispatch_rq_list(),
unfortunately the budget is held by request A.
3) meantime blk_mq_dispatch_rq_list() is called for dispatching request
A, and try to get driver tag first, unfortunately no driver tag is
available because the driver tag is held by request B
4) both two IO pathes can't move on, and IO stall is caused.
This issue can be observed when running dbench on USB storage.
This patch fixes this issue by always getting budget before getting
driver tag.
Cc: stable@vger.kernel.org Fixes: de1482974080ec9e ("blk-mq: introduce .get_budget and .put_budget in blk_mq_ops") Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request abortion is performed by overriding deadline to now and
scheduling timeout handling immediately. For the latter part, the
code was using mod_timer(timeout, 0) which can't guarantee that the
timer runs afterwards. Let's schedule the underlying work item
directly instead.
This fixes the hangs during probing reported by Sitsofe but it isn't
yet clear to me how the failure can happen reliably if it's just the
above described race condition.
Calling __stack_chk_guard_setup() in decompress_kernel() is too late
that stack checking always fails for decompress_kernel() itself. So
remove __stack_chk_guard_setup() and initialize __stack_chk_guard before
we call decompress_kernel().
Original code comes from ARM but also used for MIPS and SH, so fix them
together. If without this fix, compressed booting of these archs will
fail because stack checking is enabled by default (>=4.16).
If a task is holding a reference to a namespace on a removed controller,
the head will not be released. If the same controller is added again
later, its namespaces may not be successfully added. Instead, the user
will see kernel message "Duplicate IDs for nsid <X>".
This patch fixes that by skipping heads that don't have namespaces when
considering if a new namespace is safe to add.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com> Cc: stable@vger.kernel.org Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scsi_device_quiesce() uses synchronize_rcu() to guarantee that the
effect of blk_set_preempt_only() will be visible for percpu_ref_tryget()
calls that occur after the queue unfreeze by using the approach
explained in https://lwn.net/Articles/573497/. The rcu read lock and
unlock calls in blk_queue_enter() form a pair with the synchronize_rcu()
call in scsi_device_quiesce(). Both scsi_device_quiesce() and
blk_queue_enter() must either use regular RCU or RCU-sched.
Since neither the RCU-protected code in blk_queue_enter() nor
blk_queue_usage_counter_release() sleeps, regular RCU protection
is sufficient. Note: scsi_device_quiesce() does not have to be
modified since it already uses synchronize_rcu().
Reported-by: Tejun Heo <tj@kernel.org> Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Hannes Reinecke <hare@suse.com> Cc: Ming Lei <ming.lei@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Oleksandr Natalenko <oleksandr@natalenko.name> Cc: Martin Steigerwald <martin@lichtvoll.de> Cc: stable@vger.kernel.org # v4.15 Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a20b8a61eff81bdb7097a578752a74860e9d142 ("f2fs: allocate node
and hot data in the beginning of partition") introduces another mount
option, heap, to reset it back. But it does not do anything for heap
mode, so fix it.
Cc: stable@vger.kernel.org Signed-off-by: Yunlong Song <yunlong.song@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is wrong because it makes no sense to init() the request before a
key has been set, given that the initial state depends on the key. And
digest() is short for init() + update() + final(), so in this case
there's no need to explicitly call init() at all.
Before commit 9fa68f620041 ("crypto: hash - prevent using keyed hashes
without setting key") the extra init() had no real effect, at least for
the software HMAC implementation. (There are also hardware drivers that
implement HMAC-MD5, and it's not immediately obvious how gracefully they
handle init() before setkey().) But now the crypto API detects this
incorrect initialization and returns -ENOKEY. This is breaking NFS
mounts in some cases.
Fix it by removing the incorrect call to crypto_ahash_init().
Reported-by: Michael Young <m.a.young@durham.ac.uk> Fixes: 9fa68f620041 ("crypto: hash - prevent using keyed hashes without setting key") Fixes: fffdaef2eb4a ("gss_krb5: Add support for rc4-hmac encryption") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The APIC ID as parsed from ACPI MADT is validity checked with the
apic->apic_id_valid() callback, which depends on the selected APIC type.
For non X2APIC types APIC IDs >= 0xFF are invalid, but values > 0x7FFFFFFF
are detected as valid. This happens because the 'apicid' argument of the
apic_id_valid() callback is type 'int'. So the resulting comparison
apicid < 0xFF
evaluates to true for all unsigned int values > 0x7FFFFFFF which are handed
to default_apic_id_valid(). As a consequence, invalid APIC IDs in !X2APIC
mode are considered valid and accounted as possible CPUs.
Change the apicid argument type of the apic_id_valid() callback to u32 so
the evaluation is unsigned and returns the correct result.
[ tglx: Massaged changelog ]
Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Cc: jgross@suse.com Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: hpa@zytor.com Link: https://lkml.kernel.org/r/1523322966-10296-1-git-send-email-lirongqing@baidu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consistently use types provided by <linux/types.h> to fix the following
asm/bootparam.h userspace compilation errors:
/usr/include/asm/bootparam.h:140:2: error: unknown type name 'u16'
u16 version;
/usr/include/asm/bootparam.h:141:2: error: unknown type name 'u16'
u16 compatible_version;
/usr/include/asm/bootparam.h:142:2: error: unknown type name 'u16'
u16 pm_timer_address;
/usr/include/asm/bootparam.h:143:2: error: unknown type name 'u16'
u16 num_cpus;
/usr/include/asm/bootparam.h:144:2: error: unknown type name 'u64'
u64 pci_mmconfig_base;
/usr/include/asm/bootparam.h:145:2: error: unknown type name 'u32'
u32 tsc_khz;
/usr/include/asm/bootparam.h:146:2: error: unknown type name 'u32'
u32 apic_khz;
/usr/include/asm/bootparam.h:147:2: error: unknown type name 'u8'
u8 standard_ioapic;
/usr/include/asm/bootparam.h:148:2: error: unknown type name 'u8'
u8 cpu_ids[255];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: <stable@vger.kernel.org> # v4.16 Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4a362601baa6 ("x86/jailhouse: Add infrastructure for running in non-root cell") Link: http://lkml.kernel.org/r/20180405043210.GA13254@altlinux.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf9809 ("ath9k: Switch to using mac80211 intermediate software queues.") Cc: stable@vger.kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The block address is saved after the block is initialized when
threshold_init_device() is called.
Use the saved block address, if available, rather than trying to
rediscover it.
This will avoid a call trace, when resuming from suspend, due to the
rdmsr_safe_on_cpu() call in get_block_address(). The rdmsr_safe_on_cpu()
call issues an IPI but we're running with interrupts disabled. This
triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
Currently, bank 4 is reserved on Fam17h, so we chose not to initialize
bank 4 in the smca_banks array. This means that when we check if a bank
is initialized, like during boot or resume, we will see that bank 4 is
not initialized and try to initialize it.
This will cause a call trace, when resuming from suspend, due to
rdmsr_*on_cpu() calls in the init path. The rdmsr_*on_cpu() calls issue
an IPI but we're running with interrupts disabled. This triggers:
WARNING: CPU: 0 PID: 11523 at kernel/smp.c:291 smp_call_function_single+0xdc/0xe0
...
Reserved banks will be read-as-zero, so their MCA_IPID register will be
zero. So, like the smca_banks array, the threshold_banks array will not
have an entry for a reserved bank since all its MCA_MISC* registers will
be zero.
Enumerate a "Reserved" bank type that matches on a HWID_MCATYPE of 0,0.
Use the "Reserved" type when checking if a bank is reserved. It's
possible that other bank numbers may be reserved on future systems.
Don't try to find the block address on reserved banks.
Pass the bank number to smca_get_bank_type() since that's all we need.
Also, we should compare the bank number to MAX_NR_BANKS (size of the
smca_banks array) not the number of bank types. Bank types are reused
for multiple banks, so the number of types can be different from the
number of banks in a system and thus we could return an invalid bank
type.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: <stable@vger.kernel.org> # 4.14.x Cc: <stable@vger.kernel.org> # 4.14.x: 11cf887728a3 x86/MCE/AMD: Define a function to get SMCA bank type Cc: <stable@vger.kernel.org> # 4.14.x: c6708d50f166 x86/MCE: Report only DRAM ECC as memory errors on AMD systems Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/20180221101900.10326-6-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In randconfig testing, we sometimes get this warning:
drivers/gpu/drm/radeon/radeon_object.c: In function 'radeon_bo_create':
drivers/gpu/drm/radeon/radeon_object.c:242:2: error: #warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance thanks to write-combining [-Werror=cpp]
#warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance \
This is rather annoying since almost all other code produces no build-time
output unless we have found a real bug. We already fixed this in the
amdgpu driver in commit 31bb90f1cd08 ("drm/amdgpu: shut up #warning for
compile testing") by adding a CONFIG_COMPILE_TEST check last year and
agreed to do the same here, but both Michel and I then forgot about it
until I came across the issue again now.
For stable kernels, as this is one of very few remaining randconfig
warnings in 4.14.
Cc: stable@vger.kernel.org Link: https://patchwork.kernel.org/patch/9550009/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A use-after-free bug was caught by KASAN while running usdt related
code (BCC project. bcc/tests/python/test_usdt2.py):
==================================================================
BUG: KASAN: use-after-free in uprobe_perf_close+0x222/0x3b0
Read of size 4 at addr ffff880384f9b4a4 by task test_usdt2.py/870
The buggy address belongs to the object at ffff880384f9b480
which belongs to the cache task_struct of size 12928
It occurs because task_struct is freed before perf_event which refers
to the task and task flags are checked while teardown of the event.
perf_event_alloc() assigns task_struct to hw.target of perf_event,
but there is no reference counting for it.
As a fix we get_task_struct() in perf_event_alloc() at above mentioned
assignment and put_task_struct() in _free_event().
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 63b6da39bb38e8f1a1ef3180d32a39d6 ("perf: Fix perf_event_exit_task() race") Link: http://lkml.kernel.org/r/20180409100346.6416-1-bhole_prashant_q7@lab.ntt.co.jp Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a TIP packet is expected but there is a different packet, it is an
error. However the unexpected packet might be something important like a
TSC packet, so after the error, it is necessary to continue from there,
rather than the next packet. That is achieved by setting pkt_step to
zero.
sync_switch is a facility to synchronize decoding more closely with the
point in the kernel when the context actually switched.
The flag when sync_switch is enabled was global to the decoding, whereas
it is really specific to the CPU.
The trace data for different CPUs is put on different queues, so add
sync_switch to the intel_pt_queue structure and use that in preference
to the global setting in the intel_pt structure.
That fixes problems decoding one CPU's trace because sync_switch was
disabled on a different CPU's queue.
Overlap detection was not not updating the buffer's 'consecutive' flag.
Marking buffers consecutive has the advantage that decoding begins from
the start of the buffer instead of the first PSB. Fix overlap detection
to identify consecutive buffers correctly.
I suspect the reason is the per-cpu data is not in the linear chunk.
This could be restored if that was able to be fixed, but for now,
just remove the tracepoints.
1. With the patch "x86/vector/msi: Switch to global reservation mode",
the recent v4.15 and newer kernels always hang for 1-vCPU Hyper-V VM
with SR-IOV. This is because when we reach hv_compose_msi_msg() by
request_irq() -> request_threaded_irq() ->__setup_irq()->irq_startup()
-> __irq_startup() -> irq_domain_activate_irq() -> ... ->
msi_domain_activate() -> ... -> hv_compose_msi_msg(), local irq is
disabled in __setup_irq().
Note: when we reach hv_compose_msi_msg() by another code path:
pci_enable_msix_range() -> ... -> irq_domain_activate_irq() -> ... ->
hv_compose_msi_msg(), local irq is not disabled.
hv_compose_msi_msg() depends on an interrupt from the host.
With interrupts disabled, a UP VM always hangs in the busy loop in
the function, because the interrupt callback hv_pci_onchannelcallback()
can not be called.
We can do nothing but work it around by polling the channel. This
is ugly, but we don't have any other choice.
2. If the host is ejecting the VF device before we reach
hv_compose_msi_msg(), in a UP VM, we can hang in hv_compose_msi_msg()
forever, because at this time the host doesn't respond to the
CREATE_INTERRUPT request. This issue exists the first day the
pci-hyperv driver appears in the kernel.
Luckily, this can also by worked around by polling the channel
for the PCI_EJECT message and hpdev->state, and by checking the
PCI vendor ID.
Note: actually the above 2 issues also happen to a SMP VM, if
"hbus->hdev->channel->target_cpu == smp_processor_id()" is true.
Fixes: 4900be83602b ("x86/vector/msi: Switch to global reservation mode") Tested-by: Adrian Suhov <v-adsuho@microsoft.com> Tested-by: Chris Valean <v-chvale@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: <stable@vger.kernel.org> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we hot-remove the device, we first receive a PCI_EJECT message and
then receive a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
The first message is offloaded to hv_eject_device_work(), and the second
is offloaded to pci_devices_present_work(). Both the paths can be running
list_del(&hpdev->list_entry), causing general protection fault, because
system_wq can run them concurrently.
The patch eliminates the race condition.
Since access to present/eject work items is serialized, we do not need the
hbus->enum_sem anymore, so remove it.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Link: https://lkml.kernel.org/r/KL1P15301MB00064DA6B4D221123B5241CFBFD70@KL1P15301MB0006.APCP153.PROD.OUTLOOK.COM Tested-by: Adrian Suhov <v-adsuho@microsoft.com> Tested-by: Chris Valean <v-chvale@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: squashed semaphore removal patch] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: <stable@vger.kernel.org> # v4.6+ Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pci-hyperv driver's channel callback hv_pci_onchannelcallback() is not
really a hot path, so we don't need to mark it as a perf_device, meaning
with this patch all HV_PCIE channels' target_cpu will be CPU0.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: stable@vger.kernel.org Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the HPMC (High Priority Machine Check) handler is 16-byte
aligned and that it's length in the IVT is a multiple of 16 bytes.
Otherwise PDC may decide not to call the HPMC crash handler.
As found by the ubsan checker, the value of the 'index' variable can be
out of range for the bc[] array:
UBSAN: Undefined behaviour in arch/parisc/kernel/drivers.c:655:21
index 6 is out of range for type 'char [6]'
Backtrace:
[<104fa850>] __ubsan_handle_out_of_bounds+0x68/0x80
[<1019d83c>] check_parent+0xc0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019d86c>] check_parent+0xf0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019d938>] descend_children+0x4c/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019cffc>] hwpath_to_device+0xa4/0xc4
device_remove_group() was called on any cleanup, even if the
device attrs had not been added yet. That can occur in certain
error scenarios, so add a flag to know if it has been added.
Also make sure we remove the dev if we added it ourselves.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: stable@vger.kernel.org # 4.15 Cc: Laura Abbott <labbott@redhat.com> Tested-by: Bill Perkins <wmp@grnwood.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow dual pipelines utilising two WPF entities when available, the
VSP was updated to support header-mode display list in continuous
pipelines.
A small bug in the status check of the command register causes the
second pipeline to be directly afflicted by the running of the first;
appearing as a perceived performance issue with stuttering display.
Fix the vsp1_dl_list_hw_update_pending() call to ensure that the read
comparison corresponds to the correct pipeline.
At put_v4l2_window32(), it tries to access kp->clips. However,
kp points to an userspace pointer. So, it should be obtained
via get_user(), otherwise it can OOPS:
The size of devnode_nums[] bit array is too short to store information
for VFL_TYPE_TOUCH. That causes it to override other memory regions.
Thankfully, on recent reports, it is overriding video_device[] array,
trigging a WARN_ON(). Yet, it just warns about the problem, but let
the code excecuting, with generates an OOPS:
Each Oracle DAX CCB has a corresponding completion area, and the required
number of areas must fit within a previously allocated array of completion
areas beginning at the requested index. Since the completion area index
is specified by a file offset, a user can pass arbitrary values, including
negative numbers. So the index must be thoroughly range checked to prevent
access to addresses outside the bounds of the allocated completion
area array. The index cannot be negative, and it cannot exceed the
total array size, less the number of CCBs requested. The old code did
not check for negative values and was off by one on the upper bound.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Jonathan Helman <jonathan.helman@oracle.com> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lan78xx_read_otp tries to return -EINVAL in the event of invalid OTP
content, but the value gets overwritten before it is returned and the
read goes ahead anyway. Make the read conditional as it should be
and preserve the error code.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhost_copy_to_user is used to copy vring used elements to userspace.
We should use VHOST_ADDR_USED instead of VHOST_ADDR_DESC.
Fixes: f88949138058 ("vhost: introduce O(1) vq metadata cache") Signed-off-by: Eric Auger <eric.auger@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit dd9d598c6657 ("ip_gre: add the support for i/o_flags update via
netlink") added the ability to change o_flags, but missed that the
GSO/LLTX features are disabled by default, and only enabled some gre
features are unused. Thus we also need to disable the GSO/LLTX features
on the device when the TUNNEL_SEQ or TUNNEL_CSUM flags are set.
These two examples should result in the same features being set:
ip link add gre_none type gre local 192.168.0.10 remote 192.168.0.20 ttl 255 key 0
ip link set gre_none type gre seq
ip link add gre_seq type gre local 192.168.0.10 remote 192.168.0.20 ttl 255 key 1 seq
Fixes: dd9d598c6657 ("ip_gre: add the support for i/o_flags update via netlink") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use l2tp_tunnel_find() to prevent l2tp_nl_cmd_tunnel_create()
from creating a duplicate tunnel. A tunnel can be concurrently
registered after l2tp_tunnel_find() returns. Therefore, searching for
duplicates must be done at registration time.
Finally, remove l2tp_tunnel_find() entirely as it isn't use anywhere
anymore.
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_tunnel_create() inserts the new tunnel into the namespace's tunnel
list and sets the socket's ->sk_user_data field, before returning it to
the caller. Therefore, there are two ways the tunnel can be accessed
and freed, before the caller even had the opportunity to take a
reference. In practice, syzbot could crash the module by closing the
socket right after a new tunnel was returned to pppol2tp_create().
This patch moves tunnel registration out of l2tp_tunnel_create(), so
that the caller can safely hold a reference before publishing the
tunnel. This second step is done with the new l2tp_tunnel_register()
function, which is now responsible for associating the tunnel to its
socket and for inserting it into the namespace's list.
While moving the code to l2tp_tunnel_register(), a few modifications
have been done. First, the socket validation tests are done in a helper
function, for clarity. Also, modifying the socket is now done after
having inserted the tunnel to the namespace's tunnels list. This will
allow insertion to fail, without having to revert theses modifications
in the error path (a followup patch will check for duplicate tunnels
before insertion). Either the socket is a kernel socket which we
control, or it is a user-space socket for which we have a reference on
the file descriptor. In any case, the socket isn't going to be closed
from under us.
Reported-by: syzbot+fbeeb5c3b538e8545644@syzkaller.appspotmail.com Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the patch the short-circuit logic for A was inverted:
if (A || vq->iotlb)
return A;
return B;
This patch fixes the regression by rewriting the checks in the obvious
way, no longer returning A when vq->iotlb is non-NULL (which is hard to
understand).
Reported-by: syzbot+65a84dde0214b0387ccd@syzkaller.appspotmail.com Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On receiving a packet the state index points to the rstate which must be
used to fill up IP and TCP headers. But if the state index points to a
rstate which is unitialized, i.e. filled with zeros, it gets stuck in an
infinite loop inside ip_fast_csum trying to compute the ip checsum of a
header with zero length.
./scripts/faddr2line vmlinux slhc_uncompress+0x464/0x468 output:
ip_fast_csum at arch/arm64/include/asm/checksum.h:40
(inlined by) slhc_uncompress at drivers/net/slip/slhc.c:615
Adding a variable to indicate if the current rstate is initialized. If
such a packet arrives, move to toss state.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rds_sendmsg() calls rds_send_mprds_hash() to find a c_path to use to
send a message. Suppose the RDS connection is not yet up. In
rds_send_mprds_hash(), it does
if (conn->c_npaths == 0)
wait_event_interruptible(conn->c_hs_waitq,
(conn->c_npaths != 0));
If it is interrupted before the connection is set up,
rds_send_mprds_hash() will return a non-zero hash value. Hence
rds_sendmsg() will use a non-zero c_path to send the message. But if
the RDS connection ends up to be non-MP capable, the message will be
lost as only the zero c_path can be used.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.
The modem is controlled via AT commands through the exposed TTYs.
AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NSP default buffer is a piece of NFP memory where additional
command data can be placed. Its format has been copied from
host buffer, but the PCIe selection bits do not make sense in
this case. If those get masked out from a NFP address - writes
to random place in the chip memory may be issued and crash the
device.
Even in the general NSP buffer case, it doesn't make sense to have the
PCIe selection bits there anymore. These are unused at the moment, and
when it becomes necessary, the PCIe selection bits should rather be
moved to another register to utilise more bits for the buffer address.
This has never been an issue because the buffer used to be
allocated in memory with less-than-38-bit-long address but that
is about to change.
Fixes: 1a64821c6af7 ("nfp: add support for service processor access") Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we delete a u32 key via u32_delete_key(), we forget to
call idr_remove() to remove its handle from IDR.
Fixes: e7614370d6f0 ("net_sched: use idr to allocate u32 filter handles") Reported-by: Marcin Kabiesz <admin@hostcenter.eu> Tested-by: Marcin Kabiesz <admin@hostcenter.eu> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ip6gre_tunnel_locate+0x334/0x860 net/ipv6/ip6_gre.c:339
Write of size 20 at addr ffff8801afb9f7b8 by task syzkaller851048/4466
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in ipip6_tunnel_locate+0x63b/0xaa0 net/ipv6/sit.c:254
Write of size 33 at addr ffff8801b64076d8 by task syzkaller932654/4453
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_valid_name() to make sure user does not provide illegal
device name.
syzbot caught the following bug :
BUG: KASAN: stack-out-of-bounds in strlcpy include/linux/string.h:300 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_tunnel_create+0xca/0x6b0 net/ipv4/ip_tunnel.c:257
Write of size 20 at addr ffff8801ac79f810 by task syzkaller268107/4482
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to use dev_valid_name() to validate tunnel names,
so better use strnlen(name, IFNAMSIZ) than strlen(name) to make
sure to not upset KASAN.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like function ethtool_get_ts_info(), we should also consider the
phy_driver ts_info call back. For example, driver dp83640.
Fixes: 37dd9255b2f6 ("vlan: Pass ethtool get_ts_info queries to real device.") Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----address@SYSC_bind
Variable was created at:
SYSC_bind+0x6f/0x4b0 net/socket.c:1461
SyS_bind+0x54/0x80 net/socket.c:1460
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----addr@___sys_recvmsg
Variable was created at:
___sys_recvmsg+0xd5/0x810 net/socket.c:2172
__sys_recvmmsg+0x54e/0xdb0 net/socket.c:2313
Bytes 8-15 of 16 are uninitialized
==================================================================
Kernel panic - not syncing: panic_on_warn set ...
Once dst has been cached in socket via sk_setup_caps(),
it is illegal to call ip_rt_put() (or dst_release()),
since sk_setup_caps() did not change dst refcount.
We can still dereference it since we hold socket lock.
Caugth by syzbot :
BUG: KASAN: use-after-free in atomic_dec_return include/asm-generic/atomic-instrumented.h:198 [inline]
BUG: KASAN: use-after-free in dst_release+0x27/0xa0 net/core/dst.c:185
Write of size 4 at addr ffff8801c54dc040 by task syz-executor4/20088
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when tcf_bpf_init_from_ops() fails (e.g. because of program having invalid
number of instructions), tcf_bpf_cfg_cleanup() calls bpf_prog_put(NULL) or
bpf_prog_destroy(NULL). Unless CONFIG_BPF_SYSCALL is unset, this causes
the following error:
Fix it in tcf_bpf_cfg_cleanup(), ensuring that bpf_prog_{put,destroy}(f)
is called only when f is not NULL.
Fixes: bbc09e7842a5 ("net/sched: fix idr leak on the error path of tcf_bpf_init()") Reported-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of ip6_forward(), IPSTATS_MIB_OUTFORWDATAGRAMS and
IPSTATS_MIB_OUTOCTETS are incremented immediately before the NF_HOOK call
for NFPROTO_IPV6 / NF_INET_FORWARD. As a result, these counters get
incremented regardless of whether or not the netfilter hook allows the
packet to continue being processed. This change increments the counters
in ip6_forward_finish() so that it will not happen if the netfilter hook
chooses to terminate the packet, which is similar to how IPv4 works.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com> Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arp_filter performs an ip_route_output search for arp source address and
checks if output device is the same where the arp request was received,
if it is not, the arp request is not answered.
This route lookup is always done on main route table so l3slave devices
never find the proper route and arp is not answered.
Passing l3mdev_master_ifindex_rcu(dev) return value as oif fixes the
lookup for l3slave devices while maintaining same behavior for non
l3slave devices as this function returns 0 in that case.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change moving addr_lsb into the _sigfault union failed to take
into account that _sigfault._addr_bnd._lower being a pointer forced
the entire union to have pointer alignment. The fix for
_sigfault._addr_bnd._lower having pointer alignment failed to take
into account that m68k has a pointer alignment less than the size
of a pointer. So simply making the padding members pointers changed
the location of later members in the structure.
Fix this by directly computing the needed size of the padding members,
and making the padding members char arrays of the needed size. AKA
if __alignof__(void *) is 1 sizeof(short) otherwise __alignof__(void *).
Which should be exactly the same rules the compiler whould have
used when computing the padding.
I have tested this change by adding BUILD_BUG_ONs to m68k to verify
the offset of every member of struct siginfo, and with those testing
that the offsets of the fields in struct siginfo is the same before
I changed the generic _sigfault member and after the correction
to the _sigfault member.
I have also verified that the x86 with it's own BUILD_BUG_ONs to verify
the offsets of the siginfo members also compiles cleanly.
Cc: stable@vger.kernel.org Reported-by: Eugene Syromiatnikov <esyr@redhat.com> Fixes: 859d880cf544 ("signal: Correct the offset of si_pkey in struct siginfo") Fixes: b68a68d3dcc1 ("signal: Move addr_lsb into the _sigfault union for clarity") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined"
since at least March 1984. The Linux kernel has treated it as SGR 22
"normal intensity" since it was added in Linux-0.96b in June 1992.
Before that, it was simply ignored. Other terminal emulators have
either ignored it, or treat it as double underline now. xterm for
example added support in its 304 release (May 2014) [2] where it was
previously ignoring it.
Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no
script is using libtinfo/libcurses to look this up, or using tput
to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals
already do not work correctly on non-Linux VTs (including running
under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and
they're using SGR 21 (instead of SGR 22), the output should still
be readable.
imo it's important to change this as the Linux VT's non-conformance
is sometimes used as an argument for other terminal emulators to not
implement SGR 21 at all, or do so incorrectly.
The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request
Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Reset i8042 before probing because of insufficient BIOS initialisation of
the i8042 serial controller. This makes Synaptics touchpad detection
possible. Without resetting the Synaptics touchpad is not detected because
there are always NACK messages from AUX port.
The primary interface for the touchpad device in Thinkpad L570 is SMBus,
so ALPS overlooked PS2 interface Firmware setting of TrackStick, and
shipped with TrackStick otp bit is disabled.
The address 0xD7 contains device number information, so we can identify
the device by checking this value, but to access it we need to enable
Command mode, and then re-enable the device. Devices shipped in Thinkpad
L570 report either 0x0C or 0x1D as device numbers, if we see them we assume
that the devices are DualPoints.
The same issue exists on Dell Latitude 7370.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929 Fixes: 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads") Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Tested-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Jonathan Liu <net147@gmail.com> Tested-by: Jaak Ristioja <jaak@ristioja.ee> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 452562abb5b7 ("base: arch_topology: fix section
mismatch build warnings"). It causes the notifier call hangs in some
use-cases.
In some cases with using maxcpus, some of cpus are booted first and
then the remaining cpus are booted. As an example, some users who want
to realize fast boot up often use the following procedure.
1) Define all CPUs on device tree (CA57x4 + CA53x4)
2) Add "maxcpus=4" in bootargs
3) Kernel boot up with CA57x4
4) After kernel boot up, CA53x4 is booted from user
When kernel init was finished, CPUFREQ_POLICY_NOTIFIER was not still
unregisterd. This means that "__init init_cpu_capacity_callback()"
will be called after kernel init sequence. To avoid this problem,
it needs to remove __init{,data} annotations by reverting this commit.
Also, this commit was needed to fix kernel compile issue below.
However, this issue was also fixed by another patch: commit 82d8ba717ccb
("arch_topology: Fix section miss match warning due to
free_raw_capacity()") in v4.15 as well.
Whereas commit 452562abb5b7 added all the missing __init annotations,
commit 82d8ba717ccb removed it from free_raw_capacity().
WARNING: vmlinux.o(.text+0x548f24): Section mismatch in reference
from the function init_cpu_capacity_callback() to the variable
.init.text:$x
The function init_cpu_capacity_callback() references
the variable __init $x.
This is often because init_cpu_capacity_callback lacks a __init
annotation or the annotation of $x is wrong.
Fixes: 82d8ba717ccb ("arch_topology: Fix section miss match warning due to free_raw_capacity()") Cc: stable <stable@vger.kernel.org> Signed-off-by: Gaku Inami <gaku.inami.xh@renesas.com> Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fstests generic/475 provides a way to fail metadata reads while
checking if checksum exists for the inode inside run_delalloc_nocow(),
and csum_exist_in_range() interprets error (-EIO) as inode having
checksum and makes its caller enter the cow path.
In case of free space inode, this ends up with a warning in
cow_file_range().
The same problem applies to btrfs_cross_ref_exist() since it may also
read metadata in between.
With this, run_delalloc_nocow() bails out when errors occur at the two
places.
cc: <stable@vger.kernel.org> v2.6.28+ Fixes: 17d217fe970d ("Btrfs: fix nodatasum handling in balancing code") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 6 new ACPI HIDs to enable bluetooth on devices using these HIDs,
I've tested the following HIDs / devices:
BCM2E74: Jumper ezPad mini 3
BCM2E83: Acer Iconia Tab8 w1-810
BCM2E90: Meegopad T08
BCM2EAA: Chuwi Vi8 plus (CWI519)
The reporter of Red Hat bugzilla 1554835 has tested:
BCM2E84: Lenovo Yoga2
The reporter of kernel bugzilla 274481 has tested:
BCM2E38: Toshiba Encore
Note the Lenovo Yoga2 and Toshiba Encore also needs the earlier patch to
treat all Interrupt ACPI resources as active low.
Cc: stable@vger.kernel.org Buglink: https://bugzilla.kernel.org/attachment.cgi?id=274481 Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835 Reported-and-tested-by: Robert R. Howell <rhowell@uwyo.edu> Reported-and-tested-by: Christian Herzog <daduke@daduke.org> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log