Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.
If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.
Ugly scapy test script running on veth0:
def loop():
pkt=sniff(iface="veth0", filter="icmp6", count=1)
pkt = pkt[0]
b = bytearray(pkt[Raw].load)
b[1] += 1
b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
pkt[Raw].load = bytes(b)
pkt[IPv6].plen += 8
# fixup checksum after modifying the payload
pkt[IPv6].payload.cksum -= 0x3b44
if pkt[IPv6].payload.cksum < 0:
pkt[IPv6].payload.cksum += 0xffff
sendp(pkt, iface="veth0")
This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.
Fixes: adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.
Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc and/or allmulti to pass
the traffic in.
We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.
Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a51803 ("netvsc: optimize receive completions") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b6c5734db070 ("sctp: fix the handling of ICMP Frag Needed
for too small MTUs"), sctp_transport_update_pmtu would refetch pathmtu
from the dst and set it to transport's pathmtu without any check.
The new pathmtu may be lower than MINSEGMENT if the dst is obsolete and
updated by .get_dst() in sctp_transport_update_pmtu. In this case, it
could have a smaller MTU as well, and thus we should validate it
against MINSEGMENT instead.
Syzbot reported a warning in sctp_mtu_payload caused by this.
This patch refetches the pathmtu by calling sctp_dst_mtu where it does
the check against MINSEGMENT.
v1->v2:
- refetch the pathmtu by calling sctp_dst_mtu instead as Marcelo's
suggestion.
Fixes: b6c5734db070 ("sctp: fix the handling of ICMP Frag Needed for too small MTUs") Reported-by: syzbot+f0d9d7cba052f9344b03@syzkaller.appspotmail.com Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Which makes sure that the MTU respects the minimum value of
SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh
It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer
skb_cow_head() call was added in e41c7c68ea77 ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.
This patch moves ipv6hdr pointer assignment after skb_cow_head() call.
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support") Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fq_codel_init fails, qdisc_create_dflt will cleanup by using
qdisc_destroy. This function calls the ->reset() op prior to calling the
->destroy() op.
Unfortunately, during the failure flow for sch_fq_codel, the ->flows
parameter is not initialized, so the fq_codel_reset function will null
pointer dereference.
This is caused because flows_cnt is non-zero, but flows hasn't been
initialized. fq_codel_init has left the private data in a partially
initialized state.
To fix this, reset flows_cnt to 0 when we fail to initialize.
Additionally, to make the state more consistent, also cleanup the flows
pointer when the allocation of backlogs fails.
This fixes the NULL pointer dereference, since both the for-loop and
memset in fq_codel_reset will be no-ops when flow_cnt is zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rhashtable_free_and_destroy() cancels re-hash deferred work
then walks and destroys elements. at this moment, some elements can be
still in future_tbl. that elements are not destroyed.
test case:
nft_rhash_destroy() calls rhashtable_free_and_destroy() to destroy
all elements of sets before destroying sets and chains.
But rhashtable_free_and_destroy() doesn't destroy elements of future_tbl.
so that splat occurred.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244c0 ("ptp: Allow reassigning calibration pin function") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric reported that reverting the patch that fixed and simplified IPv6
multipath routes means reverting back to invalid userspace notifications.
eg.,
$ ip -6 route add 2001:db8:1::/64 nexthop dev eth0 nexthop dev eth1
only generates a single notification:
2001:db8:1::/64 dev eth0 metric 1024 pref medium
While working on a fix for this problem I found another case that is just
broken completely - a multipath route with a gateway followed by device
followed by gateway:
$ ip -6 ro add 2001:db8:103::/64
nexthop via 2001:db8:1::64
nexthop dev dummy2
nexthop via 2001:db8:3::64
In this case the device only route is dropped completely - no notification
to userpsace but no addition to the FIB either:
$ ip -6 ro ls
2001:db8:1::/64 dev dummy1 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy2 proto kernel metric 256 pref medium
2001:db8:3::/64 dev dummy3 proto kernel metric 256 pref medium
2001:db8:103::/64 metric 1024
nexthop via 2001:db8:1::64 dev dummy1 weight 1
nexthop via 2001:db8:3::64 dev dummy3 weight 1 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy2 proto kernel metric 256 pref medium
fe80::/64 dev dummy3 proto kernel metric 256 pref medium
Really, IPv6 multipath is just FUBAR'ed beyond repair when it comes to
device only routes, so do not allow it all.
This change will break any scripts relying on the mpath api for insert,
but I don't see any other way to handle the permutations. Besides, since
the routes are added to the FIB as standalone (non-multipath) routes the
kernel is not doing what the user requested, so it might as well tell the
user that.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin reported that icmp replies may not use the address on the device the
echo request is received if the destination address is broadcast. Instead
a route lookup is done without considering VRF context. Fix by setting
oif in flow struct to the master device if it is enslaved. That directs
the lookup to the VRF table. If the device is not enslaved, oif is still
0 so no affect.
Fixes: cd2fbe1b6b51 ("net: Use VRF device index for lookups on RX") Reported-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b7008620b84 ("net: Don't copy pfmemalloc flag in
__copy_skb_header()") introduced a different handling for the
pfmemalloc flag in copy and clone paths.
In __skb_clone(), now, the flag is set only if it was set in the
original skb, but not cleared if it wasn't. This is wrong and
might lead to socket buffers being flagged with pfmemalloc even
if the skb data wasn't allocated from pfmemalloc reserves. Copy
the flag instead of ORing it.
Reported-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 8b7008620b84 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit b19372273164 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit a9e419dc7be6 ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tcp_diag_destroy closes a TCP_NEW_SYN_RECV socket, it first
frees it by calling inet_csk_reqsk_queue_drop_and_and_put in
tcp_abort, and then frees it again by calling sock_gen_put.
Since tcp_abort only has one caller, and all the other codepaths
in tcp_abort don't free the socket, just remove the free in that
function.
Cc: David Ahern <dsa@cumulusnetworks.com>
Tested: passes Android sock_diag_test.py, which exercises this codepath Fixes: d7226c7a4dd1 ("net: diag: Fix refcnt leak in error path destroying socket") Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rhashtable_init() currently does not take into account the user-passed
min_size parameter unless param->nelem_hint is set as well. As such,
the default size (number of buckets) will always be HASH_DEFAULT_SIZE
even if the smallest allowed size is larger than that. Remediate this
by unconditionally calling into rounded_hashtable_size() and handling
things accordingly.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.
>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.
Fixes: 79ff2fc31e0f ("ila: Cache a route to translated address") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.
This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Tested-by: Pete Heist <pete@heistp.net> Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100ffffea001da3be08ffffea001da25a08ffff88084000d0c0
[ 201.039582] raw: 000000000000000000000000000d000d00000001ffffffff0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This breaks DDC in certain cases. Revert for 4.18 and previous kernels.
For 4.19, this is fixed with the following more extensive patches:
drm/amd/display: Serialize is_dp_sink_present
drm/amd/display: Break out function to simply read aux reply
drm/amd/display: Return aux replies directly to DRM
drm/amd/display: Right shift AUX reply value sooner than later
drm/amd/display: Read AUX channel even if only status byte is returned
Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.
Without this, there could not be enough slots, which could trigger the
BUG_ON in reservation_object_add_shared_fence.
v2:
* Jump to the error label instead of returning directly (Jerry Zhang)
v3:
* Reserve slots for command submission after VM updates (Christian König)
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/106418 Reported-by: mikhail.v.gavrilov@gmail.com Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror
SPRN_USPRG3 are used as userspace VDSO write and read registers
respectively.
SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not
restored. As a result, any read from SPRN_USPRG3 returns zero on an
exit from stop4 (Power9 only) and above.
Thus in this situation, on POWER9, any call from sched_getcpu() always
returns zero, as on powerpc, we call __kernel_getcpu() which relies
upon SPRN_USPRG3 to report the CPU and NUMA node information.
Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state
with the sprg_vdso value that is cached in PACA.
Fixes: e1c1cfed5432 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Florian Weimer <fweimer@redhat.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cpu_stop_queue_two_works() begins to wake the stopper threads, it does
so without preemption disabled, which leads to the following race
condition:
The source CPU calls cpu_stop_queue_two_works(), with cpu1 as the source
CPU, and cpu2 as the destination CPU. When adding the stopper threads to
the wake queue used in this function, the source CPU stopper thread is
added first, and the destination CPU stopper thread is added last.
When wake_up_q() is invoked to wake the stopper threads, the threads are
woken up in the order that they are queued in, so the source CPU's stopper
thread is woken up first, and it preempts the thread running on the source
CPU.
The stopper thread will then execute on the source CPU, disable preemption,
and begin executing multi_cpu_stop(), and wait for an ack from the
destination CPU's stopper thread, with preemption still disabled. Since the
worker thread that woke up the stopper thread on the source CPU is affine
to the source CPU, and preemption is disabled on the source CPU, that
thread will never run to dequeue the destination CPU's stopper thread from
the wake queue, and thus, the destination CPU's stopper thread will never
run, causing the source CPU's stopper thread to wait forever, and stall.
Disable preemption when waking the stopper threads in
cpu_stop_queue_two_works().
The size is always equal to 1 page so let's use this. Later on this will
be used for other checks which use page shifts to check the granularity
of access.
This should cause no behavioral change.
Cc: stable@vger.kernel.org # v4.12+ Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing info.index before indirectly using it to index
vdev->region
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744da (intel_pstate: skip the driver if ACPI has power mgmt option) Reported-by: Andreas Herrmann <aherrmann@suse.com> Reviewed-by: Andreas Herrmann <aherrmann@suse.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Andreas Herrmann <aherrmann@suse.com> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__split_huge_pmd_locked() must check if the cleared huge pmd was dirty,
and propagate that to PageDirty: otherwise, data may be lost when a huge
tmpfs page is modified then split then reclaimed.
How has this taken so long to be noticed? Because there was no problem
when the huge page is written by a write system call (shmem_write_end()
calls set_page_dirty()), nor when the page is allocated for a write fault
(fault_dirty_shared_page() calls set_page_dirty()); but when allocated for
a read fault (which MAP_POPULATE simulates), no set_page_dirty().
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1807111741430.1106@eggly.anvils Fixes: d21b9e57c74c ("thp: handle file pages in split_huge_pmd()") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Ashwin Chaugule <ashwinch@google.com> Reviewed-by: Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that a kernel crash happened in mem_cgroup_iter(), which
can be triggered if the legacy cgroup-v1 non-hierarchical mode is used.
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f
......
Call trace:
mem_cgroup_iter+0x2e0/0x6d4
shrink_zone+0x8c/0x324
balance_pgdat+0x450/0x640
kswapd+0x130/0x4b8
kthread+0xe8/0xfc
ret_from_fork+0x10/0x20
mem_cgroup_iter():
......
if (css_tryget(css)) <-- crash here
break;
......
The crashing reason is that mem_cgroup_iter() uses the memcg object whose
pointer is stored in iter->position, which has been freed before and
filled with POISON_FREE(0x6b).
And the root cause of the use-after-free issue is that
invalidate_reclaim_iterators() fails to reset the value of iter->position
to NULL when the css of the memcg is released in non- hierarchical mode.
Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com Fixes: 6df38689e0e9 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim") Signed-off-by: Jing Xia <jing.xia.mail@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <chunyan.zhang@unisoc.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mprotect(EXEC) was failing for stack mappings as default vm flags was
missing MAYEXEC.
This was triggered by glibc test suite nptl/tst-execstack testcase
What is surprising is that despite running LTP for years on, we didn't
catch this issue as it lacks a directed test case.
gcc dejagnu tests with nested functions also requiring exec stack work
fine though because they rely on the GNU_STACK segment spit out by
compiler and handled in kernel elf loader.
This glibc case is different as the stack is non exec to begin with and
a dlopen of shared lib with GNU_STACK segment triggers the exec stack
proceedings using a mprotect(PROT_EXEC) which was broken.
We used to have pre-set CONFIG_INITRAMFS_SOURCE with local path
to intramfs in ARC defconfigs. This was quite convenient for
in-house development but not that convenient for newcomers
who obviusly don't have folders like "arc_initramfs" next to
the Linux source tree. Which leads to quite surprising failure
of defconfig building:
------------------------------->8-----------------------------
../scripts/gen_initramfs_list.sh: Cannot open '../../arc_initramfs_hs/'
../usr/Makefile:57: recipe for target 'usr/initramfs_data.cpio.gz' failed
make[2]: *** [usr/initramfs_data.cpio.gz] Error 1
------------------------------->8-----------------------------
So now when more and more people start to deal with our defconfigs
let's make their life easier with removal of CONFIG_INITRAMFS_SOURCE.
swap was broken on ARC due to silly copy-paste issue.
We encode offset from swapcache page in __swp_entry() as (off << 13) but
were not decoding back in __swp_offset() as (off >> 13) - it was still
(off << 13).
This manifsted as strace segfaulting on HSDK because gcc was targetting
the accumulator registers as GPRs, which kernek was not saving/restoring
by default.
The SNDRV_RAWMIDI_IOCTL_PARAMS ioctl may resize the buffers and the
current code is racy. For example, the sequencer client may write to
buffer while it being resized.
As a simple workaround, let's switch to the resized buffer inside the
stream runtime lock.
In parse_options(), if match_strdup() failed, parse_options() leaves
opts->iocharset in unexpected state (i.e. still pointing the freed
string). And this can be the cause of double free.
To fix, this initialize opts->iocharset always when freeing.
commit b3b7c4795c ("x86/MCE: Serialize sysfs changes") introduced a min
interval limitation when setting the check interval for polled MCEs.
However, the logic is that 0 disables polling for corrected MCEs, see
Documentation/x86/x86_64/machinecheck. The limitation prevents disabling.
Remove this limitation and allow the value 0 to disable polling again.
Markus reported that BTS is sporadically missing the tail of the trace
in the perf_event data buffer: [decode error (1): instruction overflow]
shown in GDB; and bisected it to the conversion of debug_store to PTI.
A little "optimization" crept into alloc_bts_buffer(), which mistakenly
placed bts_interrupt_threshold away from the 24-byte record boundary.
Intel SDM Vol 3B 17.4.9 says "This address must point to an offset from
the BTS buffer base that is a multiple of the BTS record size."
Revert "max" from a byte count to a record count, to calculate the
bts_interrupt_threshold correctly: which turns out to fix problem seen.
Fixes: c1961a4631da ("x86/events/intel/ds: Map debug buffers in cpu_entry_area") Reported-and-tested-by: Markus T Metzger <markus.t.metzger@intel.com> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@intel.com> Cc: Andi Kleen <andi.kleen@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org # v4.14+ Link: https://lkml.kernel.org/r/alpine.LSU.2.11.1807141248290.1614@eggly.anvils Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: dd84441a7971 ("x86/speculation: Use IBRS if available before calling into firmware") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709133534.5963-1-ville.syrjala@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pvti_cpu0_va is the address of shared kvmclock data structure.
pvti_cpu0_va is currently kept unset (1) on 32 bit systems, (2) when
kvmclock vsyscall is disabled, and (3) if kvmclock is not stable.
This poses a problem, because kvm_ptp needs pvti_cpu0_va, but (1) can
work on 32 bit, (2) has little relation to the vsyscall, and (3) does
not need stable kvmclock (although kvmclock won't be used for system
clock if it's not stable, so kvm_ptp is pointless in that case).
Expose pvti_cpu0_va whenever kvmclock is enabled to allow all users to
work with it.
This fixes a regression found on Gentoo: https://bugs.gentoo.org/658544.
Fixes: 9f08890ab906 ("x86/pvclock: add setter for pvclock_pvti_cpu0_va") Cc: stable@vger.kernel.org Reported-by: Andreas Steinmetz <ast@domdv.de> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we switched from doing rdmsr() to reading FS/GS base values from
current->thread we completely forgot about legacy 32-bit userspaces which
we still support in KVM (why?). task->thread.{fsbase,gsbase} are only
synced for 64-bit processes, calling save_fsgs_for_kvm() and using
its result from current is illegal for legacy processes.
There's no ARCH_SET_FS/GS prctls for legacy applications. Base MSRs are,
however, not always equal to zero. Intel's manual says (3.4.4 Segment
Loading Instructions in IA-32e Mode):
"In order to set up compatibility mode for an application, segment-load
instructions (MOV to Sreg, POP Sreg) work normally in 64-bit mode. An
entry is read from the system descriptor table (GDT or LDT) and is loaded
in the hidden portion of the segment register.
...
The hidden descriptor register fields for FS.base and GS.base are
physically mapped to MSRs in order to load all address bits supported by
a 64-bit implementation.
"
The issue was found by strace test suite where 32-bit ioctl_kvm_run test
started segfaulting.
Reported-by: Dmitry V. Levin <ldv@altlinux.org> Bisected-by: Masatake YAMATO <yamato@redhat.com> Fixes: 42b933b59721 ("x86/kvm/vmx: read MSR_{FS,KERNEL_GS}_BASE from current->thread") Cc: stable@vger.kernel.org Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When eVMCS is enabled, all VMCS allocated to be used by KVM are marked
with revision_id of KVM_EVMCS_VERSION instead of revision_id reported
by MSR_IA32_VMX_BASIC.
However, even though not explictly documented by TLFS, VMXArea passed
as VMXON argument should still be marked with revision_id reported by
physical CPU.
This issue was found by the following setup:
* L0 = KVM which expose eVMCS to it's L1 guest.
* L1 = KVM which consume eVMCS reported by L0.
This setup caused the following to occur:
1) L1 execute hardware_enable().
2) hardware_enable() calls kvm_cpu_vmxon() to execute VMXON.
3) L0 intercept L1 VMXON and execute handle_vmon() which notes
vmxarea->revision_id != VMCS12_REVISION and therefore fails with
nested_vmx_failInvalid() which sets RFLAGS.CF.
4) L1 kvm_cpu_vmxon() don't check RFLAGS.CF for failure and therefore
hardware_enable() continues as usual.
5) L1 hardware_enable() then calls ept_sync_global() which executes
INVEPT.
6) L0 intercept INVEPT and execute handle_invept() which notes
!vmx->nested.vmxon and thus raise a #UD to L1.
7) Raised #UD caused L1 to panic.
A comment warning against this bug is there, but the code is not doing what
the comment says. Therefore it is possible that an EPOLLHUP races against
irq_bypass_register_consumer. The EPOLLHUP handler schedules irqfd_shutdown,
and if that runs soon enough, you get a use-after-free.
Reported-by: syzbot <syzkaller@googlegroups.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reports crashes in kvm_irqfd_assign(), caused by use-after-free
when kvm_irqfd_assign() and kvm_irqfd_deassign() run in parallel
for one specific eventfd. When the assign path hasn't finished but irqfd
has been added to kvm->irqfds.items list, another thead may deassign the
eventfd and free struct kvm_kernel_irqfd(). The assign path then uses
the struct kvm_kernel_irqfd that has been freed by deassign path. To avoid
such issue, keep irqfd under kvm->irq_srcu protection after the irqfd
has been added to kvm->irqfds.items list, and call synchronize_srcu()
in irq_shutdown() to make sure that irqfd has been fully initialized in
the assign path.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Tianyu Lan <tianyu.lan@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes crash for FCoE adapter. Once driver initialization is
complete, firmware will start posting Asynchronous Event, However driver
has not yet allocated workqueue to process and queue up work. This delay
of allocating workqueue results into NULL pointer access.
Cc: <stable@vger.kernel.org> # v4.17+ Fixes: 9b3e0f4d4147 ("scsi: qla2xxx: Move work element processing out of DPC thread" Reported-by: Li Wang <liwang@redhat.com> Tested-by: Li Wang <liwang@redhat.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPNFT command allocates 2 buffer for switch query. On completion, the same
buffers were freed using different size, instead of using original size at
the time of allocation.
This patch saves the size of the request and response buffers and uses that
to free them.
Following stack trace can be seen when using debug kernel
Fix the description of sd_zbc_check_zone_size() to correctly explain that
the returned value is a number of device blocks, not bytes. Additionally,
the 32 bits "ret" variable used in this function may truncate the 64 bits
zone_blocks variable value upon return. To fix this, change "ret" type to
s64.
Fixes: ccce20fc79 ("sd_zbc: Avoid that resetting a zone fails sporadically") Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: stable@kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Partially undo commit 9facc336876f ("bpf: reject any prog that failed
read-only lock") since it caused a regression, that is, syzkaller was
able to manage to cause a panic via fault injection deep in set_memory_ro()
path by letting an allocation fail: In x86's __change_page_attr_set_clr()
it was able to change the attributes of the primary mapping but not in
the alias mapping via cpa_process_alias(), so the second, inner call
to the __change_page_attr() via __change_page_attr_set_clr() had to split
a larger page and failed in the alloc_pages() with the artifically triggered
allocation error which is then propagated down to the call site.
Thus, for set_memory_ro() this means that it returned with an error, but
from debugging a probe_kernel_write() revealed EFAULT on that memory since
the primary mapping succeeded to get changed. Therefore the subsequent
hdr->locked = 0 reset triggered the panic as it was performed on read-only
memory, so call-site assumptions were infact wrong to assume that it would
either succeed /or/ not succeed at all since there's no such rollback in
set_memory_*() calls from partial change of mappings, in other words, we're
left in a state that is "half done". A later undo via set_memory_rw() is
succeeding though due to matching permissions on that part (aka due to the
try_preserve_large_page() succeeding). While reproducing locally with
explicitly triggering this error, the initial splitting only happens on
rare occasions and in real world it would additionally need oom conditions,
but that said, it could partially fail. Therefore, it is definitely wrong
to bail out on set_memory_ro() error and reject the program with the
set_memory_*() semantics we have today. Shouldn't have gone the extra mile
since no other user in tree today infact checks for any set_memory_*()
errors, e.g. neither module_enable_ro() / module_disable_ro() for module
RO/NX handling which is mostly default these days nor kprobes core with
alloc_insn_page() / free_insn_page() as examples that could be invoked long
after bootup and original 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks") did neither when it got first introduced to BPF
so "improving" with bailing out was clearly not right when set_memory_*()
cannot handle it today.
Kees suggested that if set_memory_*() can fail, we should annotate it with
__must_check, and all callers need to deal with it gracefully given those
set_memory_*() markings aren't "advisory", but they're expected to actually
do what they say. This might be an option worth to move forward in future
but would at the same time require that set_memory_*() calls from supporting
archs are guaranteed to be "atomic" in that they provide rollback if part
of the range fails, once that happened, the transition from RW -> RO could
be made more robust that way, while subsequent RO -> RW transition /must/
continue guaranteeing to always succeed the undo part.
Reported-by: syzbot+a4eb8c7766952a1ca872@syzkaller.appspotmail.com Reported-by: syzbot+d866d1925855328eac3b@syzkaller.appspotmail.com Fixes: 9facc336876f ("bpf: reject any prog that failed read-only lock") Cc: Laura Abbott <labbott@redhat.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any eBPF JIT that where its underlying arch supports ARCH_HAS_SET_MEMORY
would need to use bpf_jit_binary_{un,}lock_ro() pair instead of the
set_memory_{ro,rw}() pair directly as otherwise changes to the former
might break. arm32's eBPF conversion missed to change it, so fix this
up here.
After commit 9facc336876f ("bpf: reject any prog that failed read-only lock")
offsetof(struct bpf_binary_header, image) became 3 instead of 4,
breaking powerpc BPF badly, since instructions need to be word aligned.
Fixes: 9facc336876f ("bpf: reject any prog that failed read-only lock") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all our infrastructure is in place, let's expose the
availability of ARCH_WORKAROUND_2 to guests. We take this opportunity
to tidy up a couple of SMCCC constants.
Acked-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to forward the guest's ARCH_WORKAROUND_2 calls to EL3,
add a small(-ish) sequence to handle it at EL2. Special care must
be taken to track the state of the guest itself by updating the
workaround flags. We also rely on patching to enable calls into
the firmware.
Note that since we need to execute branches, this always executes
after the Spectre-v2 mitigation has been applied.
Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to offer ARCH_WORKAROUND_2 support to guests, we need
a bit of infrastructure.
Let's add a flag indicating whether or not the guest uses
SSBD mitigation. Depending on the state of this flag, allow
KVM to disable ARCH_WORKAROUND_2 before entering the guest,
and enable it when exiting it.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we're going to require to access per-cpu variables at EL2,
let's craft the minimum set of accessors required to implement
reading a per-cpu variable, relying on tpidr_el2 to contain the
per-cpu offset.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If running on a system that performs dynamic SSBD mitigation, allow
userspace to request the mitigation for itself. This is implemented
as a prctl call, allowing the mitigation to be enabled or disabled at
will for this particular thread.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to allow userspace to be mitigated on demand, let's
introduce a new thread flag that prevents the mitigation from
being turned off when exiting to userspace, and doesn't turn
it on on entry into the kernel (with the assumption that the
mitigation is always enabled in the kernel itself).
This will be used by a prctl interface introduced in a later
patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system where firmware can dynamically change the state of the
mitigation, the CPU will always come up with the mitigation enabled,
including when coming back from suspend.
If the user has requested "no mitigation" via a command line option,
let's enforce it by calling into the firmware again to disable it.
Similarily, for a resume from hibernate, the mitigation could have
been disabled by the boot kernel. Let's ensure that it is set
back on in that case.
Acked-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid checking arm64_ssbd_callback_required on each
kernel entry/exit even if no mitigation is required, let's
add yet another alternative that by default jumps over the mitigation,
and that gets nop'ed out if we're doing dynamic mitigation.
Think of it as a poor man's static key...
Reviewed-by: Julien Grall <julien.grall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system where the firmware implements ARCH_WORKAROUND_2,
it may be useful to either permanently enable or disable the
workaround for cases where the user decides that they'd rather
not get a trap overhead, and keep the mitigation permanently
on or off instead of switching it on exception entry/exit.
In any case, default to the mitigation being enabled.
Reviewed-by: Julien Grall <julien.grall@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the kernel to protect itself, let's call the SSBD mitigation
implemented by the higher exception level (either hypervisor or firmware)
on each transition between userspace and kernel.
We must take the PSCI conduit into account in order to target the
right exception level, hence the introduction of a runtime patching
callback.
Reviewed-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Julien Grall <julien.grall@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've so far used the PSCI return codes for SMCCC because they
were extremely similar. But with the new ARM DEN 0070A specification,
"NOT_REQUIRED" (-2) is clashing with PSCI's "PSCI_RET_INVALID_PARAMS".
Let's bite the bullet and add SMCCC specific return codes. Users
can be repainted as and when required.
Acked-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly, tbl->entries is not initialized after kmalloc(),
therefore causes an uninit-value warning in ip_vs_lblc_check_expire(),
as reported by syzbot.
Reported-by: <syzbot+3e9695f147fb529aa9bc@syzkaller.appspotmail.com> Cc: Simon Horman <horms@verge.net.au> Cc: Julian Anastasov <ja@ssi.bg> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Julian Anastasov <ja@ssi.bg> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting stalls at nfc_llcp_send_ui_frame() [1]. This is
because nfc_llcp_send_ui_frame() is retrying the loop without any delay
when nonblocking nfc_alloc_send_skb() returned NULL.
Since there is no need to use MSG_DONTWAIT if we retry until
sock_alloc_send_pskb() succeeds, let's use blocking call.
Also, in case an unexpected error occurred, let's break the loop
if blocking nfc_alloc_send_skb() failed.
What happens in jit_subprogs() is that kcalloc() for the subprog func
buffer is failing with NULL where we then bail out. Latter is a plain
return -ENOMEM, and this is definitely not okay since earlier in the
loop we are walking all subprogs and temporarily rewrite insn->off to
remember the subprog id as well as insn->imm to temporarily point the
call to __bpf_call_base + 1 for the initial JIT pass. Thus, bailing
out in such state and handing this over to the interpreter is troublesome
since later/subsequent e.g. find_subprog() lookups are based on wrong
insn->imm.
Therefore, once we hit this point, we need to jump to out_free path
where we undo all changes from earlier loop, so that interpreter can
work on unmodified insn->{off,imm}.
Another point is that should find_subprog() fail in jit_subprogs() due
to a verifier bug, then we also should not simply defer the program to
the interpreter since also here we did partial modifications. Instead
we should just bail out entirely and return an error to the user who is
trying to load the program.
Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs") Reported-by: syzbot+7d427828b2ea6e592804@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when a sock is closed and the bpf_tcp_close() callback is
used we remove memory but do not free the skb. Call consume_skb() if
the skb is attached to the buffer.
This fixes a crash where we assign tcp_prot to IPv6 sockets instead
of tcpv6_prot.
Previously we overwrote the sk->prot field with tcp_prot even in the
AF_INET6 case. This patch ensures the correct tcp_prot and tcpv6_prot
are used.
Tested with 'netserver -6' and 'netperf -H [IPv6]' as well as
'netperf -H [IPv4]'. The ESTABLISHED check resolves the previously
crashing case here.
Fixes: 174a79ff9515 ("bpf: sockmap with sk redirect support") Reported-by: syzbot+5c063698bdbfac19f363@syzkaller.appspotmail.com Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we end up splitting a bio and the queue goes away between
the initial submission and the later split submission, then we
can block forever in blk_queue_enter() waiting for the reference
to drop to zero. This will never happen, since we already hold
a reference.
Mark a split bio as already having entered the queue, so we can
just use the live non-blocking queue enter variant.
Loop transport which is self loopback, remote port congestion
update isn't relevant. Infact the xmit path already ignores it.
Receive path needs to do the same.
Reported-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently lock any JITed image as read-only via bpf_jit_binary_lock_ro()
as well as the BPF image as read-only through bpf_prog_lock_ro(). In
the case any of these would fail we throw a WARN_ON_ONCE() in order to
yell loudly to the log. Perhaps, to some extend, this may be comparable
to an allocation where __GFP_NOWARN is explicitly not set.
Added via 65869a47f348 ("bpf: improve read-only handling"), this behavior
is slightly different compared to any of the other in-kernel set_memory_ro()
users who do not check the return code of set_memory_ro() and friends /at
all/ (e.g. in the case of module_enable_ro() / module_disable_ro()). Given
in BPF this is mandatory hardening step, we want to know whether there
are any issues that would leave both BPF data writable. So it happens
that syzkaller enabled fault injection and it triggered memory allocation
failure deep inside x86's change_page_attr_set_clr() which was triggered
from set_memory_ro().
Now, there are two options: i) leaving everything as is, and ii) reworking
the image locking code in order to have a final checkpoint out of the
central bpf_prog_select_runtime() which probes whether any of the calls
during prog setup weren't successful, and then bailing out with an error.
Option ii) is a better approach since this additional paranoia avoids
altogether leaving any potential W+X pages from BPF side in the system.
Therefore, lets be strict about it, and reject programs in such unlikely
occasion. While testing I noticed also that one bpf_prog_lock_ro()
call was missing on the outer dummy prog in case of calls, e.g. in the
destructor we call bpf_prog_free_deferred() on the main prog where we
try to bpf_prog_unlock_free() the program, and since we go via
bpf_prog_select_runtime() do that as well.
Reported-by: syzbot+3b889862e65a98317058@syzkaller.appspotmail.com Reported-by: syzbot+9e762b52dd17e616a7a5@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting NULL pointer dereference at wb_workfn() [1] due to
wb->bdi->dev being NULL. And Dmitry confirmed that wb->state was
WB_shutting_down after wb->bdi->dev became NULL. This indicates that
unregister_bdi() failed to call wb_shutdown() on one of wb objects.
The problem is in cgwb_bdi_unregister() which does cgwb_kill() and thus
drops bdi's reference to wb structures before going through the list of
wbs again and calling wb_shutdown() on each of them. This way the loop
iterating through all wbs can easily miss a wb if that wb has already
passed through cgwb_remove_from_bdi_list() called from wb_shutdown()
from cgwb_release_workfn() and as a result fully shutdown bdi although
wb_workfn() for this wb structure is still running. In fact there are
also other ways cgwb_bdi_unregister() can race with
cgwb_release_workfn() leading e.g. to use-after-free issues:
We solve these issues by synchronizing writeback structure shutdown from
cgwb_bdi_unregister() with cgwb_release_workfn() using a new mutex. That
way we also no longer need synchronization using WB_shutting_down as the
mutex provides it for CONFIG_CGROUP_WRITEBACK case and without
CONFIG_CGROUP_WRITEBACK wb_shutdown() can be called only once from
bdi_unregister().
Reported-by: syzbot <syzbot+4a7438e774b21ddd8eca@syzkaller.appspotmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet reports:
Here is a reproducer of an annoying bug detected by syzkaller on our production kernel
[..]
./b78305423 enable_conntrack
Then :
sleep 60
dmesg | tail -10
[ 171.599093] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 181.631024] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 191.687076] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 201.703037] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 211.711072] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 221.959070] unregister_netdevice: waiting for lo to become free. Usage count = 2
Reproducer sends ipv6 fragment that hits nfct defrag via LOCAL_OUT hook.
skb gets queued until frag timer expiry -- 1 minute.
Normally nf_conntrack_reasm gets called during prerouting, so skb has
no dst yet which might explain why this wasn't spotted earlier.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Tested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The autofs subsystem does not check that the "path" parameter is present
for all cases where it is required when it is passed in via the "param"
struct.
In particular it isn't checked for the AUTOFS_DEV_IOCTL_OPENMOUNT_CMD
ioctl command.
To solve it, modify validate_dev_ioctl(function to check that a path has
been provided for ioctl commands that require it.
Link: http://lkml.kernel.org/r/153060031527.26631.18306637892746301555.stgit@pluto.themaw.net Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: syzbot+60c837b428dc84e83a93@syzkaller.appspotmail.com Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the zerocopy sendmsg() path, there are error checks to revert
the zerocopy if we get any error code. syzkaller has discovered
that tls_push_record can return -ECONNRESET, which is fatal, and
happens after the point at which it is safe to revert the iter,
as we've already passed the memory to do_tcp_sendpages.
Previously this code could return -ENOMEM and we would want to
revert the iter, but AFAIK this no longer returns ENOMEM after a447da7d004 ("tls: fix waitall behavior in tls_sw_recvmsg"),
so we fail for all error codes.
Reported-by: syzbot+c226690f7b3126c5ee04@syzkaller.appspotmail.com Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com Signed-off-by: Dave Watson <davejwatson@fb.com> Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My recent fix for dns_resolver_preparse() printing very long strings was
incomplete, as shown by syzbot which still managed to hit the
WARN_ONCE() in set_precision() by adding a crafted "dns_resolver" key:
precision 50001 too large
WARNING: CPU: 7 PID: 864 at lib/vsprintf.c:2164 vsnprintf+0x48a/0x5a0
The bug this time isn't just a printing bug, but also a logical error
when multiple options ("#"-separated strings) are given in the key
payload. Specifically, when separating an option string into name and
value, if there is no value then the name is incorrectly considered to
end at the end of the key payload, rather than the end of the current
option. This bypasses validation of the option length, and also means
that specifying multiple options is broken -- which presumably has gone
unnoticed as there is currently only one valid option anyway.
A similar problem also applied to option values, as the kstrtoul() when
parsing the "dnserror" option will read past the end of the current
option and into the next option.
Fix these bugs by correctly computing the length of the option name and
by copying the option value, null-terminated, into a temporary buffer.
Reproducer for "dnserror" option being parsed incorrectly (expected
behavior is to fail when seeing the unknown option "foo", actual
behavior was to read the dnserror value as "1#foo" and fail there):
Reported-by: syzbot <syzkaller@googlegroups.com> Fixes: 4a2d789267e0 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ReiserFS prepares log messages into a 1024-byte buffer with no bounds
checks. Long messages, such as the "unknown mount option" warning when
userspace passes a crafted mount options string, overflow this buffer.
This causes KASAN to report a global-out-of-bounds write.
Fix it by truncating messages to the buffer size.
Link: http://lkml.kernel.org/r/20180707203621.30922-1-ebiggers3@gmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+b890b3335a4d8c608963@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the ebtables evaluation loop expects targets to return
positive values (jumps), or negative values (absolute verdicts).
This is completely different from what xtables does.
In xtables, targets are expected to return the standard netfilter
verdicts, i.e. NF_DROP, NF_ACCEPT, etc.
ebtables will consider these as jumps.
Therefore reject any target found due to unspec fallback.
v2: also reject watchers. ebtables ignores their return value, so
a target that assumes skb ownership (and returns NF_STOLEN) causes
use-after-free.
The only watchers in the 'ebtables' front-end are log and nflog;
both have AF_BRIDGE specific wrappers on kernel side.
Commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
uses local_bh_disable()/enable(), because hv_pci_onchannelcallback() can
also run in tasklet context as the channel event callback, so bottom halves
should be disabled to prevent a race condition.
With CONFIG_PROVE_LOCKING=y in the recent mainline, or old kernels that
don't have commit f71b74bca637 ("irq/softirqs: Use lockdep to assert IRQs
are disabled/enabled"), when the upper layer IRQ code calls
hv_compose_msi_msg() with local IRQs disabled, we'll see a warning at the
beginning of __local_bh_enable_ip():
IRQs not enabled as expected
WARNING: CPU: 0 PID: 408 at kernel/softirq.c:162 __local_bh_enable_ip
The warning exposes an issue in de0aa7b2f97d: local_bh_enable() can
potentially call do_softirq(), which is not supposed to run when local IRQs
are disabled. Let's fix this by using local_irq_save()/restore() instead.
Note: hv_pci_onchannelcallback() is not a hot path because it's only called
when the PCI device is hot added and removed, which is infrequent.
Fixes: de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()") Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: stable@vger.kernel.org Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log