The introduction of generic_max_swapfile_size and arch-specific versions has
broken linking on x86 with CONFIG_SWAP=n due to undefined reference to
'generic_max_swapfile_size'. Fix it by compiling the x86-specific
max_swapfile_size() only with CONFIG_SWAP=y.
Commit 0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
breaks non-SMP builds.
[ I suspect the 'bool' fields should just be made to be bitfields and be
exposed regardless of configuration, but that's a separate cleanup
that I'll leave to the owners of this file for later. - Linus ]
Fixes: 0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once") Cc: Dave Hansen <dave.hansen@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Abel Vesa <abelvesa@linux.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function has an inline "return false;" definition with CONFIG_SMP=n
but the "real" definition is also visible leading to "redefinition of
‘apic_id_is_primary_thread’" compiler error.
The mmio tracer sets io mapping PTEs and PMDs to non present when enabled
without inverting the address bits, which makes the PTE entry vulnerable
for L1TF.
Make it use the right low level macros to actually invert the address bits
to protect against L1TF.
In principle this could be avoided because MMIO tracing is not likely to be
enabled on production machines, but the fix is straigt forward and for
consistency sake it's better to get rid of the open coded PTE manipulation.
set_memory_np() is used to mark kernel mappings not present, but it has
it's own open coded mechanism which does not have the L1TF protection of
inverting the address bits.
Replace the open coded PTE manipulation with the L1TF protecting low level
PTE routines.
Some cases in THP like:
- MADV_FREE
- mprotect
- split
mark the PMD non present for temporarily to prevent races. The window for
an L1TF attack in these contexts is very small, but it wants to be fixed
for correctness sake.
Use the proper low level functions for pmd/pud_mknotpresent() to address
this.
For kernel mappings PAGE_PROTNONE is not necessarily set for a non present
mapping, but the inversion logic explicitely checks for !PRESENT and
PROT_NONE.
Remove the PROT_NONE check and make the inversion unconditional for all not
present mappings.
Josh reported that the late SMT evaluation in cpu_smt_state_init() sets
cpu_smt_control to CPU_SMT_NOT_SUPPORTED in case that 'nosmt' was supplied
on the kernel command line as it cannot differentiate between SMT disabled
by BIOS and SMT soft disable via 'nosmt'. That wreckages the state and
makes the sysfs interface unusable.
Rework this so that during bringup of the non boot CPUs the availability of
SMT is determined in cpu_smt_allowed(). If a newly booted CPU is not a
'primary' thread then set the local cpu_smt_available marker and evaluate
this explicitely right after the initial SMP bringup has finished.
SMT evaulation on x86 is a trainwreck as the firmware has all the
information _before_ booting the kernel, but there is no interface to query
it.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS") Reported-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nested virtualization is in use, VMENTER operations from the nested
hypervisor into the nested guest will always be processed by the bare metal
hypervisor, and KVM's "conditional cache flushes" mode in particular does a
flush on nested vmentry. Therefore, include the "skip L1D flush on
vmentry" bit in KVM's suggested ARCH_CAPABILITIES setting.
Add the relevant Documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 3 of ARCH_CAPABILITIES tells a hypervisor that L1D flush on vmentry is
not needed. Add a new value to enum vmx_l1d_flush_state, which is used
either if there is no L1TF bug at all, or if bit 3 is set in ARCH_CAPABILITIES.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last missing piece to having vmx_l1d_flush() take interrupts after
VMEXIT into account is to set the kvm_cpu_l1tf_flush_l1d per-cpu flag on
irq entry.
Issue calls to kvm_set_cpu_l1tf_flush_l1d() from entering_irq(),
ipi_entering_ack_irq(), smp_reschedule_interrupt() and
uv_bau_message_interrupt().
Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Part of the L1TF mitigation for vmx includes flushing the L1D cache upon
VMENTRY.
L1D flushes are costly and two modes of operations are provided to users:
"always" and the more selective "conditional" mode.
If operating in the latter, the cache would get flushed only if a host side
code path considered unconfined had been traversed. "Unconfined" in this
context means that it might have pulled in sensitive data like user data
or kernel crypto keys.
The need for L1D flushes is tracked by means of the per-vcpu flag
l1tf_flush_l1d. KVM exit handlers considered unconfined set it. A
vmx_l1d_flush() subsequently invoked before the next VMENTER will conduct a
L1d flush based on its value and reset that flag again.
Currently, interrupts delivered "normally" while in root operation between
VMEXIT and VMENTER are not taken into account. Part of the reason is that
these don't leave any traces and thus, the vmx code is unable to tell if
any such has happened.
As proposed by Paolo Bonzini, prepare for tracking all interrupts by
introducing a new per-cpu flag, "kvm_cpu_l1tf_flush_l1d". It will be in
strong analogy to the per-vcpu ->l1tf_flush_l1d.
A later patch will make interrupt handlers set it.
For the sake of cache locality, group kvm_cpu_l1tf_flush_l1d into x86'
per-cpu irq_cpustat_t as suggested by Peter Zijlstra.
Provide the helpers kvm_set_cpu_l1tf_flush_l1d(),
kvm_clear_cpu_l1tf_flush_l1d() and kvm_get_cpu_l1tf_flush_l1d(). Make them
trivial resp. non-existent for !CONFIG_KVM_INTEL as appropriate.
Let vmx_l1d_flush() handle kvm_cpu_l1tf_flush_l1d in the same way as
l1tf_flush_l1d.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An upcoming patch will extend KVM's L1TF mitigation in conditional mode
to also cover interrupts after VMEXITs. For tracking those, stores to a
new per-cpu flag from interrupt handlers will become necessary.
In order to improve cache locality, this new flag will be added to x86's
irq_cpustat_t.
Make some space available there by shrinking the ->softirq_pending bitfield
from 32 to 16 bits: the number of bits actually used is only NR_SOFTIRQS,
i.e. 10.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vmx_l1d_flush_always static key is only ever evaluated if
vmx_l1d_should_flush is enabled. In that case however, there are only two
L1d flushing modes possible: "always" and "conditional".
The "conditional" mode's implementation tends to require more sophisticated
logic than the "always" mode.
Avoid inverted logic by replacing the 'vmx_l1d_flush_always' static key
with a 'vmx_l1d_flush_cond' one.
If SMT is disabled in BIOS, the CPU code doesn't properly detect it.
The /sys/devices/system/cpu/smt/control file shows 'on', and the 'l1tf'
vulnerabilities file shows SMT as vulnerable.
Fix it by forcing 'cpu_smt_control' to CPU_SMT_NOT_SUPPORTED in such a
case. Unfortunately the detection can only be done after bringing all
the CPUs online, so we have to overwrite any previous writes to the
variable.
Reported-by: Joe Mario <jmario@redhat.com> Tested-by: Jiri Kosina <jkosina@suse.cz> Fixes: f048c399e0f7 ("x86/topology: Provide topology_smt_supported()") Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The slow path in vmx_l1d_flush() reads from vmx_l1d_flush_pages in order
to evict the L1d cache.
However, these pages are never cleared and, in theory, their data could be
leaked.
More importantly, KSM could merge a nested hypervisor's vmx_l1d_flush_pages
to fewer than 1 << L1D_CACHE_ORDER host physical pages and this would break
the L1d flushing algorithm: L1D on x86_64 is tagged by physical addresses.
Fix this by initializing the individual vmx_l1d_flush_pages with a
different pattern each.
Rename the "empty_zp" asm constraint identifier in vmx_l1d_flush() to
"flush_pages" to reflect this change.
pfn_modify_allowed() and arch_has_pfn_modify_check() are outside of the
!__ASSEMBLY__ section in include/asm-generic/pgtable.h, which confuses
assembler on archs that don't have __HAVE_ARCH_PFN_MODIFY_ALLOWED (e.g.
ia64) and breaks build:
include/asm-generic/pgtable.h: Assembler messages:
include/asm-generic/pgtable.h:538: Error: Unknown opcode `static inline bool pfn_modify_allowed(unsigned long pfn,pgprot_t prot)'
include/asm-generic/pgtable.h:540: Error: Unknown opcode `return true'
include/asm-generic/pgtable.h:543: Error: Unknown opcode `static inline bool arch_has_pfn_modify_check(void)'
include/asm-generic/pgtable.h:545: Error: Unknown opcode `return false'
arch/ia64/kernel/entry.S:69: Error: `mov' does not fit into bundle
Move those two static inlines into the !__ASSEMBLY__ section so that they
don't confuse the asm build pass.
Fixes: 42e4089c7890 ("x86/speculation/l1tf: Disallow non privileged high MMIO PROT_NONE mappings") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce the 'l1tf=' kernel command line option to allow for boot-time
switching of mitigation that is used on processors affected by L1TF.
The possible values are:
full
Provides all available mitigations for the L1TF vulnerability. Disables
SMT and enables all mitigations in the hypervisors. SMT control via
/sys/devices/system/cpu/smt/control is still possible after boot.
Hypervisors will issue a warning when the first VM is started in
a potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
full,force
Same as 'full', but disables SMT control. Implies the 'nosmt=force'
command line option. sysfs control of SMT and the hypervisor flush
control is disabled.
flush
Leaves SMT enabled and enables the conditional hypervisor mitigation.
Hypervisors will issue a warning when the first VM is started in a
potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
flush,nosmt
Disables SMT and enables the conditional hypervisor mitigation. SMT
control via /sys/devices/system/cpu/smt/control is still possible
after boot. If SMT is reenabled or flushing disabled at runtime
hypervisors will issue a warning.
flush,nowarn
Same as 'flush', but hypervisors will not warn when
a VM is started in a potentially insecure configuration.
off
Disables hypervisor mitigations and doesn't emit any warnings.
Default is 'flush'.
Let KVM adhere to these semantics, which means:
- 'lt1f=full,force' : Performe L1D flushes. No runtime control
possible.
- 'l1tf=full'
- 'l1tf-flush'
- 'l1tf=flush,nosmt' : Perform L1D flushes and warn on VM start if
SMT has been runtime enabled or L1D flushing
has been run-time enabled
- 'l1tf=flush,nowarn' : Perform L1D flushes and no warnings are emitted.
- 'l1tf=off' : L1D flushes are not performed and no warnings
are emitted.
KVM can always override the L1D flushing behavior using its 'vmentry_l1d_flush'
module parameter except when lt1f=full,force is set.
This makes KVM's private 'nosmt' option redundant, and as it is a bit
non-systematic anyway (this is something to control globally, not on
hypervisor level), remove that option.
Add the missing Documentation entry for the l1tf vulnerability sysfs file
while at it.
All mitigation modes can be switched at run time with a static key now:
- Use sysfs_streq() instead of strcmp() to handle the trailing new line
from sysfs writes correctly.
- Make the static key management handle multiple invocations properly.
- Set the module parameter file to RW
In preparation of allowing run time control for L1D flushing, move the
setup code to the module parameter handler.
In case of pre module init parsing, just store the value and let vmx_init()
do the actual setup after running kvm_init() so that enable_ept is having
the correct state.
During run-time invoke it directly from the parameter setter to prepare for
run-time control.
If Extended Page Tables (EPT) are disabled or not supported, no L1D
flushing is required. The setup function can just avoid setting up the L1D
flush for the EPT=n case.
Invoke it after the hardware setup has be done and enable_ept has the
correct state and expose the EPT disabled state in the mitigation status as
well.
The VMX module parameter to control the L1D flush should become
writeable.
The MSR list is set up at VM init per guest VCPU, but the run time
switching is based on a static key which is global. Toggling the MSR list
at run time might be feasible, but for now drop this optimization and use
the regular MSR write to make run-time switching possible.
The default mitigation is the conditional flush anyway, so for extra
paranoid setups this will add some small overhead, but the extra code
executed is in the noise compared to the flush itself.
Aside of that the EPT disabled case is not handled correctly at the moment
and the MSR list magic is in the way for fixing that as well.
If it's really providing a significant advantage, then this needs to be
revisited after the code is correct and the control is writable.
Writing 'off' to /sys/devices/system/cpu/smt/control offlines all SMT
siblings. Writing 'on' merily enables the abilify to online them, but does
not online them automatically.
Make 'on' more useful by onlining all offline siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IA32_FLUSH_CMD MSR needs only to be written on VMENTER. Extend
add_atomic_switch_msr() with an entry_only parameter to allow storing the
MSR only in the guest (ENTRY) MSR array.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no semantic change but this change allows an unbalanced amount of
MSRs to be loaded on VMEXIT and VMENTER, i.e. the number of MSRs to save or
restore on VMEXIT or VMENTER may be different.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
336996-Speculative-Execution-Side-Channel-Mitigations.pdf defines a new MSR
(IA32_FLUSH_CMD aka 0x10B) which has similar write-only semantics to other
MSRs defined in the document.
The semantics of this MSR is to allow "finer granularity invalidation of
caching structures than existing mechanisms like WBINVD. It will writeback
and invalidate the L1 data cache, including all cachelines brought in by
preceding instructions, without invalidating all caches (eg. L2 or
LLC). Some processors may also invalidate the first level level instruction
cache on a L1D_FLUSH command. The L1 data and instruction caches may be
shared across the logical processors of a core."
Use it instead of the loop based L1 flush algorithm.
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199511
[ tglx: Avoid allocating pages when the MSR is available ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To mitigate the L1 Terminal Fault vulnerability it's required to flush L1D
on VMENTER to prevent rogue guests from snooping host memory.
CPUs will have a new control MSR via a microcode update to flush L1D with a
single MSR write, but in the absence of microcode a fallback to a software
based flush algorithm is required.
Add a software flush loop which is based on code from Intel.
[ tglx: Split out from combo patch ]
[ bpetkov: Polish the asm code ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a mitigation mode parameter "vmentry_l1d_flush" for CVE-2018-3620, aka
L1 terminal fault. The valid arguments are:
- "always" L1D cache flush on every VMENTER.
- "cond" Conditional L1D cache flush, explained below
- "never" Disable the L1D cache flush mitigation
"cond" is trying to avoid L1D cache flushes on VMENTER if the code executed
between VMEXIT and VMENTER is considered safe, i.e. is not bringing any
interesting information into L1D which might exploited.
[ tglx: Split out from a larger patch ]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the L1TF CPU bug is present we allow the KVM module to be loaded as the
major of users that use Linux and KVM have trusted guests and do not want a
broken setup.
Cloud vendors are the ones that are uncomfortable with CVE 2018-3620 and as
such they are the ones that should set nosmt to one.
Setting 'nosmt' means that the system administrator also needs to disable
SMT (Hyper-threading) in the BIOS, or via the 'nosmt' command line
parameter, or via the /sys/devices/system/cpu/smt/control. See commit 05736e4ac13c ("cpu/hotplug: Provide knobs to control SMT").
Other mitigations are to use task affinity, cpu sets, interrupt binding,
etc - anything to make sure that _only_ the same guests vCPUs are running
on sibling threads.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the way Machine Check Exceptions work on X86 hyperthreads it's
required to boot up _all_ logical cores at least once in order to set the
CR4.MCE bit.
So instead of ignoring the sibling threads right away, let them boot up
once so they can configure themselves. After they came out of the initial
boot stage check whether its a "secondary" sibling and cancel the operation
which puts the CPU back into offline state.
Reported-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen reported, that it's outright dangerous to keep SMT siblings
disabled completely so they are stuck in the BIOS and wait for SIPI.
The reason is that Machine Check Exceptions are broadcasted to siblings and
the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
reboots the machine. The MCE chapter in the SDM contains the following
blurb:
Because the logical processors within a physical package are tightly
coupled with respect to shared hardware resources, both logical
processors are notified of machine check errors that occur within a
given physical processor. If machine-check exceptions are enabled when
a fatal error is reported, all the logical processors within a physical
package are dispatched to the machine-check exception handler. If
machine-check exceptions are disabled, the logical processors enter the
shutdown state and assert the IERR# signal. When enabling machine-check
exceptions, the MCE flag in control register CR4 should be set for each
logical processor.
Reverting the commit which ignores siblings at enumeration time solves only
half of the problem. The core cpuhotplug logic needs to be adjusted as
well.
This thoughtful engineered mechanism also turns the boot process on all
Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
before the secondary CPUs are brought up. Depending on the number of
physical cores the window in which this situation can happen is smaller or
larger. On a HSW-EX it's about 750ms:
MCE is enabled on the boot CPU:
[ 0.244017] mce: CPU supports 22 MCE banks
The corresponding sibling #72 boots:
[ 1.008005] .... node #0, CPUs: #72
That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
between these two points the machine is going to shutdown. At least it's a
known safe state.
It's obvious that the early boot can be hit by an MCE as well and then runs
into the same situation because MCEs are not yet enabled on the boot CPU.
But after enabling them on the boot CPU, it does not make any sense to
prevent the kernel from recovering.
Adjust the nosmt kernel parameter documentation as well.
Reverts: 2207def700f9 ("x86/apic: Ignore secondary threads if nosmt=force") Reported-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan has noticed that pte_pfn and co. resp. pfn_pte are incorrect for
CONFIG_PAE because phys_addr_t is wider than unsigned long and so the
pte_val reps. shift left would get truncated. Fix this up by using proper
types.
Fixes: 6b28baca9b1f ("x86/speculation/l1tf: Protect PROT_NONE PTEs against speculation") Reported-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PAE 3-level paging code currently doesn't mitigate L1TF by flipping the
offset bits, and uses the high PTE word, thus bits 32-36 for type, 37-63 for
offset. The lower word is zeroed, thus systems with less than 4GB memory are
safe. With 4GB to 128GB the swap type selects the memory locations vulnerable
to L1TF; with even more memory, also the swap offfset influences the address.
This might be a problem with 32bit PAE guests running on large 64bit hosts.
By continuing to keep the whole swap entry in either high or low 32bit word of
PTE we would limit the swap size too much. Thus this patch uses the whole PAE
PTE with the same layout as the 64bit version does. The macros just become a
bit tricky since they assume the arch-dependent swp_entry_t to be 32bit.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TOPOEXT reenablement is a workaround for broken BIOSen which didn't
enable the CPUID bit. amd_get_topology_early(), however, relies on
that bit being set so that it can read out the CPUID leaf and set
smp_num_siblings properly.
Move the reenablement up to early_init_amd(). While at it, simplify
amd_get_topology_early().
nosmt on the kernel command line merely prevents the onlining of the
secondary SMT siblings.
nosmt=force makes the APIC detection code ignore the secondary SMT siblings
completely, so they even do not show up as possible CPUs. That reduces the
amount of memory allocations for per cpu variables and saves other
resources from being allocated too large.
This is not fully equivalent to disabling SMT in the BIOS because the low
level SMT enabling in the BIOS can result in partitioning of resources
between the siblings, which is not undone by just ignoring them. Some CPUs
can use the full resources when their sibling is not onlined, but this is
depending on the CPU family and model and it's not well documented whether
this applies to all partitioned resources. That means depending on the
workload disabling SMT in the BIOS might result in better performance.
Linus analysis of the Intel manual:
The intel optimization manual is not very clear on what the partitioning
rules are.
I find:
"In general, the buffers for staging instructions between major pipe
stages are partitioned. These buffers include µop queues after the
execution trace cache, the queues after the register rename stage, the
reorder buffer which stages instructions for retirement, and the load
and store buffers.
In the case of load and store buffers, partitioning also provided an
easier implementation to maintain memory ordering for each logical
processor and detect memory ordering violations"
but some of that partitioning may be relaxed if the HT thread is "not
active":
"In Intel microarchitecture code name Sandy Bridge, the micro-op queue
is statically partitioned to provide 28 entries for each logical
processor, irrespective of software executing in single thread or
multiple threads. If one logical processor is not active in Intel
microarchitecture code name Ivy Bridge, then a single thread executing
on that processor core can use the 56 entries in the micro-op queue"
but I do not know what "not active" means, and how dynamic it is. Some of
that partitioning may be entirely static and depend on the early BIOS
disabling of HT, and even if we park the cores, the resources will just be
wasted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support force disabling of SMT it's required to know the number of
thread siblings early. amd_get_topology() cannot be called before the APIC
driver is selected, so split out the part which initializes
smp_num_siblings and invoke it from amd_early_init().
Old code used to check whether CPUID ext max level is >= 0x80000008 because
that last leaf contains the number of cores of the physical CPU. The three
functions called there now do not depend on that leaf anymore so the check
can go.
Make use of the new early detection function to initialize smp_num_siblings
on the boot cpu before the MP-Table or ACPI/MADT scan happens. That's
required for force disabling SMT.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_extended_topology() cannot be called before
the APIC driver is selected, so split out the part which initializes
smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support force disabling of SMT it's required to know the number of
thread siblings early. detect_ht() cannot be called before the APIC driver
is selected, so split out the part which initializes smp_num_siblings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asymmetry caused a warning to trigger if the bootup was stopped in state
CPUHP_AP_ONLINE_IDLE. The warning no longer triggers as kthread_park() can
now be invoked on already or still parked threads. But there is still no
reason to have this be asymmetric.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the CPU is supporting SMT then the primary thread can be found by
checking the lower APIC ID bits for zero. smp_num_siblings is used to build
the mask for the APIC ID bits which need to be taken into account.
This uses the MPTABLE or ACPI/MADT supplied APIC ID, which can be different
than the initial APIC ID in CPUID. But according to AMD the lower bits have
to be consistent. Intel gave a tentative confirmation as well.
Preparatory patch to support disabling SMT at boot/runtime.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The static key sched_smt_present is only updated at boot time when SMT
siblings have been detected. Booting with maxcpus=1 and bringing the
siblings online after boot rebuilds the scheduling domains correctly but
does not update the static key, so the SMT code is not enabled.
Let the key be updated in the scheduler CPU hotplug code to fix this.
Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the L1TF workaround its necessary to limit the swap file size to below
MAX_PA/2, so that the higher bits of the swap offset inverted never point
to valid memory.
Add a mechanism for the architecture to override the swap file size check
in swapfile.c and add a x86 specific max swapfile check function that
enforces that limit.
The check is only enabled if the CPU is vulnerable to L1TF.
In VMs with 42bit MAX_PA the typical limit is 2TB now, on a native system
with 46bit PA it is 32TB. The limit is only per individual swap file, so
it's always possible to exceed these limits with multiple swap files or
partitions.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For L1TF PROT_NONE mappings are protected by inverting the PFN in the page
table entry. This sets the high bits in the CPU's address space, thus
making sure to point to not point an unmapped entry to valid cached memory.
Some server system BIOSes put the MMIO mappings high up in the physical
address space. If such an high mapping was mapped to unprivileged users
they could attack low memory by setting such a mapping to PROT_NONE. This
could happen through a special device driver which is not access
protected. Normal /dev/mem is of course access protected.
To avoid this forbid PROT_NONE mappings or mprotect for high MMIO mappings.
Valid page mappings are allowed because the system is then unsafe anyways.
It's not expected that users commonly use PROT_NONE on MMIO. But to
minimize any impact this is only enforced if the mapping actually refers to
a high MMIO address (defined as the MAX_PA-1 bit being set), and also skip
the check for root.
For mmaps this is straight forward and can be handled in vm_insert_pfn and
in remap_pfn_range().
For mprotect it's a bit trickier. At the point where the actual PTEs are
accessed a lot of state has been changed and it would be difficult to undo
on an error. Since this is a uncommon case use a separate early page talk
walk pass for MMIO PROT_NONE mappings that checks for this condition
early. For non MMIO and non PROT_NONE there are no changes.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L1TF core kernel workarounds are cheap and normally always enabled, However
they still should be reported in sysfs if the system is vulnerable or
mitigated. Add the necessary CPU feature/bug bits.
- Extend the existing checks for Meltdowns to determine if the system is
vulnerable. All CPUs which are not vulnerable to Meltdown are also not
vulnerable to L1TF
- Check for 32bit non PAE and emit a warning as there is no practical way
for mitigation due to the limited physical address bits
- If the system has more than MAX_PA/2 physical memory the invert page
workarounds don't protect the system against the L1TF attack anymore,
because an inverted physical address will also point to valid
memory. Print a warning in this case and report that the system is
vulnerable.
Add a function which returns the PFN limit for the L1TF mitigation, which
will be used in follow up patches for sanity and range checks.
[ tglx: Renamed the CPU feature bit to L1TF_PTEINV ]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The L1TF workaround doesn't make any attempt to mitigate speculate accesses
to the first physical page for zeroed PTEs. Normally it only contains some
data from the early real mode BIOS.
It's not entirely clear that the first page is reserved in all
configurations, so add an extra reservation call to make sure it is really
reserved. In most configurations (e.g. with the standard reservations)
it's likely a nop.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PTEs are set to PROT_NONE the kernel just clears the Present bit and
preserves the PFN, which creates attack surface for L1TF speculation
speculation attacks.
This is important inside guests, because L1TF speculation bypasses physical
page remapping. While the host has its own migitations preventing leaking
data from other VMs into the guest, this would still risk leaking the wrong
page inside the current guest.
This uses the same technique as Linus' swap entry patch: while an entry is
is in PROTNONE state invert the complete PFN part part of it. This ensures
that the the highest bit will point to non existing memory.
The invert is done by pte/pmd_modify and pfn/pmd/pud_pte for PROTNONE and
pte/pmd/pud_pfn undo it.
This assume that no code path touches the PFN part of a PTE directly
without using these primitives.
This doesn't handle the case that MMIO is on the top of the CPU physical
memory. If such an MMIO region was exposed by an unpriviledged driver for
mmap it would be possible to attack some real memory. However this
situation is all rather unlikely.
For 32bit non PAE the inversion is not done because there are really not
enough bits to protect anything.
Q: Why does the guest need to be protected when the HyperVisor already has
L1TF mitigations?
A: Here's an example:
Physical pages 1 2 get mapped into a guest as
GPA 1 -> PA 2
GPA 2 -> PA 1
through EPT.
The L1TF speculation ignores the EPT remapping.
Now the guest kernel maps GPA 1 to process A and GPA 2 to process B, and
they belong to different users and should be isolated.
A sets the GPA 1 PA 2 PTE to PROT_NONE to bypass the EPT remapping and
gets read access to the underlying physical page. Which in this case
points to PA 2, so it can read process B's data, if it happened to be in
L1, so isolation inside the guest is broken.
There's nothing the hypervisor can do about this. This mitigation has to
be done in the guest itself.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With L1 terminal fault the CPU speculates into unmapped PTEs, and resulting
side effects allow to read the memory the PTE is pointing too, if its
values are still in the L1 cache.
For swapped out pages Linux uses unmapped PTEs and stores a swap entry into
them.
To protect against L1TF it must be ensured that the swap entry is not
pointing to valid memory, which requires setting higher bits (between bit
36 and bit 45) that are inside the CPUs physical address space, but outside
any real memory.
To do this invert the offset to make sure the higher bits are always set,
as long as the swap file is not too big.
Note there is no workaround for 32bit !PAE, or on systems which have more
than MAX_PA/2 worth of memory. The later case is very unlikely to happen on
real systems.
[AK: updated description and minor tweaks by. Split out from the original
patch ]
If pages are swapped out, the swap entry is stored in the corresponding
PTE, which has the Present bit cleared. CPUs vulnerable to L1TF speculate
on PTE entries which have the present bit set and would treat the swap
entry as phsyical address (PFN). To mitigate that the upper bits of the PTE
must be set so the PTE points to non existent memory.
The swap entry stores the type and the offset of a swapped out page in the
PTE. type is stored in bit 9-13 and offset in bit 14-63. The hardware
ignores the bits beyond the phsyical address space limit, so to make the
mitigation effective its required to start 'offset' at the lowest possible
bit so that even large swap offsets do not reach into the physical address
space limit bits.
Move offset to bit 9-58 and type to bit 59-63 which are the bits that
hardware generally doesn't care about.
That, in turn, means that if you on desktop chip with only 40 bits of
physical addressing, now that the offset starts at bit 9, there needs to be
30 bits of offset actually *in use* until bit 39 ends up being set, which
means when inverted it will again point into existing memory.
So that's 4 terabyte of swap space (because the offset is counted in pages,
so 30 bits of offset is 42 bits of actual coverage). With bigger physical
addressing, that obviously grows further, until the limit of the offset is
hit (at 50 bits of offset - 62 bits of actual swap file coverage).
This is a preparatory change for the actual swap entry inversion to protect
against L1TF.
[ AK: Updated description and minor tweaks. Split into two parts ]
[ tglx: Massaged changelog ]
L1 Terminal Fault (L1TF) is a speculation related vulnerability. The CPU
speculates on PTE entries which do not have the PRESENT bit set, if the
content of the resulting physical address is available in the L1D cache.
The OS side mitigation makes sure that a !PRESENT PTE entry points to a
physical address outside the actually existing and cachable memory
space. This is achieved by inverting the upper bits of the PTE. Due to the
address space limitations this only works for 64bit and 32bit PAE kernels,
but not for 32bit non PAE.
This mitigation applies to both host and guest kernels, but in case of a
64bit host (hypervisor) and a 32bit PAE guest, inverting the upper bits of
the PAE address space (44bit) is not enough if the host has more than 43
bits of populated memory address space, because the speculation treats the
PTE content as a physical host address bypassing EPT.
The host (hypervisor) protects itself against the guest by flushing L1D as
needed, but pages inside the guest are not protected against attacks from
other processes inside the same guest.
For the guest the inverted PTE mask has to match the host to provide the
full protection for all pages the host could possibly map into the
guest. The hosts populated address space is not known to the guest, so the
mask must cover the possible maximal host address space, i.e. 52 bit.
On 32bit PAE the maximum PTE mask is currently set to 44 bit because that
is the limit imposed by 32bit unsigned long PFNs in the VMs. This limits
the mask to be below what the host could possible use for physical pages.
The L1TF PROT_NONE protection code uses the PTE masks to determine which
bits to invert to make sure the higher bits are set for unmapped entries to
prevent L1TF speculation attacks against EPT inside guests.
In order to invert all bits that could be used by the host, increase
__PHYSICAL_PAGE_SHIFT to 52 to match 64bit.
The real limit for a 32bit PAE kernel is still 44 bits because all Linux
PTEs are created from unsigned long PFNs, so they cannot be higher than 44
bits on a 32bit kernel. So these extra PFN bits should be never set. The
only users of this macro are using it to look at PTEs, so it's safe.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The article "Spectre Returns! Speculation Attacks using the Return Stack
Buffer" [1] describes two new (sub-)variants of spectrev2-like attacks,
making use solely of the RSB contents even on CPUs that don't fallback to
BTB on RSB underflow (Skylake+).
Mitigate userspace-userspace attacks by always unconditionally filling RSB on
context switch when the generic spectrev2 mitigation has been enabled.
[1] https://arxiv.org/pdf/1807.07940.pdf
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/nycvar.YFH.7.76.1807261308190.997@cbobk.fhfr.pm Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nadav reported that on guests we're failing to rewrite the indirect
calls to CALLEE_SAVE paravirt functions. In particular the
pv_queued_spin_unlock() call is left unpatched and that is all over the
place. This obviously wrecks Spectre-v2 mitigation (for paravirt
guests) which relies on not actually having indirect calls around.
The reason is an incorrect clobber test in paravirt_patch_call(); this
function rewrites an indirect call with a direct call to the _SAME_
function, there is no possible way the clobbers can be different
because of this.
Therefore remove this clobber check. Also put WARNs on the other patch
failure case (not enough room for the instruction) which I've not seen
trigger in my (limited) testing.
Three live kernel image disassemblies for lock_sock_nested (as a small
function that illustrates the problem nicely). PRE is the current
situation for guests, POST is with this patch applied and NATIVE is with
or without the patch for !guests.
Linus Torvalds [Sun, 12 Aug 2018 19:52:05 +0000 (12:52 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes.
The most important one is the mpt3sas fix which makes the driver work
again on big endian systems. The rest are mostly minor error path or
checker issues and the vmw_scsi one fixes a performance problem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pvscsi: Return DID_RESET for status SAM_STAT_COMMAND_TERMINATED
scsi: sr: Avoid that opening a CD-ROM hangs with runtime power management enabled
scsi: mpt3sas: Swap I/O memory read value back to cpu endianness
scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO
scsi: fcoe: drop frames in ELS LOGO error path
scsi: fcoe: fix use-after-free in fcoe_ctlr_els_send
scsi: qedi: Fix a potential buffer overflow
scsi: qla2xxx: Fix memory leak for allocating abort IOCB
Linus Torvalds [Sun, 12 Aug 2018 19:19:42 +0000 (12:19 -0700)]
init: rename and re-order boot_cpu_state_init()
This is purely a preparatory patch for upcoming changes during the 4.19
merge window.
We have a function called "boot_cpu_state_init()" that isn't really
about the bootup cpu state: that is done much earlier by the similarly
named "boot_cpu_init()" (note lack of "state" in name).
This function initializes some hotplug CPU state, and needs to run after
the percpu data has been properly initialized. It even has a comment to
that effect.
Except it _doesn't_ actually run after the percpu data has been properly
initialized. On x86 it happens to do that, but on at least arm and
arm64, the percpu base pointers are initialized by the arch-specific
'smp_prepare_boot_cpu()' hook, which ran _after_ boot_cpu_state_init().
This had some unexpected results, and in particular we have a patch
pending for the merge window that did the obvious cleanup of using
'this_cpu_write()' in the cpu hotplug init code:
which is obviously the right thing to do. Except because of the
ordering issue, it actually failed miserably and unexpectedly on arm64.
So this just fixes the ordering, and changes the name of the function to
be 'boot_cpu_hotplug_init()' to make it obvious that it's about cpu
hotplug state, because the core CPU state was supposed to have already
been done earlier.
Marked for stable, since the (not yet merged) patch that will show this
problem is marked for stable.
Linus Torvalds [Sun, 12 Aug 2018 18:21:17 +0000 (11:21 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of race fixes, mostly around lazy pathwalk.
All of it is -stable fodder, a large part going back to 2013"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make sure that __dentry_kill() always invalidates d_seq, unhashed or not
fix __legitimize_mnt()/mntput() race
fix mntput/mntput race
root dentries need RCU-delayed freeing
4) Fix loss of runtime PM on failed vlan add/del, from Ivan
Khoronzhuk.
5) xen-netfront caches skb_shinfo(skb) across a __pskb_pull_tail()
call, which potentially changes the skb's data buffer, and thus
skb_shinfo(). Fix from Juergen Gross"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
xen/netfront: don't cache skb_shinfo()
net: ethernet: ti: cpsw: fix runtime_pm while add/kill vlan
net: ethernet: ti: cpsw: clear all entries when delete vid
xdp: fix bug in devmap teardown code path
samples/bpf: xdp_redirect_cpu adjustment to reproduce teardown race easier
xdp: fix bug in cpumap teardown code path
bpf, sockmap: fix cork timeout for select due to epipe
bpf, sockmap: fix leak in bpf_tcp_sendmsg wait for mem path
bpf, sockmap: fix bpf_tcp_sendmsg sock error handling
bpf: btf: Change tools/lib/bpf/btf to LGPL
Juergen Gross [Thu, 9 Aug 2018 14:42:16 +0000 (16:42 +0200)]
xen/netfront: don't cache skb_shinfo()
skb_shinfo() can change when calling __pskb_pull_tail(): Don't cache
its return value.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 Aug 2018 16:38:53 +0000 (09:38 -0700)]
Merge branch 'cpsw-runtime-pm-fix'
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw: fix runtime pm while add/del reserved vid
Here 2 not critical fixes for:
- vlan ale table leak while error if deleting vlan (simplifies next fix)
- runtime pm while try to set reserved vlan
====================
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Fri, 10 Aug 2018 12:47:09 +0000 (15:47 +0300)]
net: ethernet: ti: cpsw: fix runtime_pm while add/kill vlan
It's exclusive with normal behaviour but if try to set vlan to one of
the reserved values is made, the cpsw runtime pm is broken.
Fixes: a6c5d14f5136 ("drivers: net: cpsw: ndev: fix accessing to suspended device") Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Fri, 10 Aug 2018 12:47:08 +0000 (15:47 +0300)]
net: ethernet: ti: cpsw: clear all entries when delete vid
In cases if some of the entries were not found in forwarding table
while killing vlan, the rest not needed entries still left in the
table. No need to stop, as entry was deleted anyway. So fix this by
returning error only after all was cleaned. To implement this, return
-ENOENT in cpsw_ale_del_mcast() as it's supposed to be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Minchan Kim [Sat, 11 Aug 2018 00:23:10 +0000 (17:23 -0700)]
zram: remove BD_CAP_SYNCHRONOUS_IO with writeback feature
If zram supports writeback feature, it's no longer a
BD_CAP_SYNCHRONOUS_IO device beause zram does asynchronous IO operations
for incompressible pages.
Do not pretend to be synchronous IO device. It makes the system very
sluggish due to waiting for IO completion from upper layers.
Furthermore, it causes a user-after-free problem because swap thinks the
opearion is done when the IO functions returns so it can free the page
(e.g., lock_page_or_retry and goto out_release in do_swap_page) but in
fact, IO is asynchronous so the driver could access a just freed page
afterward.
This patch fixes the problem.
BUG: Bad page state in process qemu-system-x86 pfn:3dfab21
page:ffffdfb137eac840 count:0 mapcount:0 mapping:0000000000000000 index:0x1
flags: 0x17fffc000000008(uptodate)
raw: 017fffc000000008dead000000000100dead0000000002000000000000000000
raw: 0000000000000001000000000000000000000000ffffffff0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
bad because of flags: 0x8(uptodate)
CPU: 4 PID: 1039 Comm: qemu-system-x86 Tainted: G B 4.18.0-rc5+ #1
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0b 05/02/2017
Call Trace:
dump_stack+0x5c/0x7b
bad_page+0xba/0x120
get_page_from_freelist+0x1016/0x1250
__alloc_pages_nodemask+0xfa/0x250
alloc_pages_vma+0x7c/0x1c0
do_swap_page+0x347/0x920
__handle_mm_fault+0x7b4/0x1110
handle_mm_fault+0xfc/0x1f0
__get_user_pages+0x12f/0x690
get_user_pages_unlocked+0x148/0x1f0
__gfn_to_pfn_memslot+0xff/0x3c0 [kvm]
try_async_pf+0x87/0x230 [kvm]
tdp_page_fault+0x132/0x290 [kvm]
kvm_mmu_page_fault+0x74/0x570 [kvm]
kvm_arch_vcpu_ioctl_run+0x9b3/0x1990 [kvm]
kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
do_vfs_ioctl+0xa2/0x630
ksys_ioctl+0x70/0x80
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Andrey Ryabinin [Sat, 11 Aug 2018 00:23:03 +0000 (17:23 -0700)]
lib/ubsan: remove null-pointer checks
With gcc-8 fsanitize=null become very noisy. GCC started to complain
about things like &a->b, where 'a' is NULL pointer. There is no NULL
dereference, we just calculate address to struct member. It's
technically undefined behavior so UBSAN is correct to report it. But as
long as there is no real NULL-dereference, I think, we should be fine.
-fno-delete-null-pointer-checks compiler flag should protect us from any
consequences. So let's just no use -fsanitize=null as it's not useful
for us. If there is a real NULL-deref we will see crash. Even if
userspace mapped something at NULL (root can do this), with things like
SMAP should catch the issue.
Linus Torvalds [Fri, 10 Aug 2018 17:04:56 +0000 (10:04 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A single driver bugfix for I2C.
The bug was found by systematically stress testing the driver, so I am
confident to merge it that late in the cycle although it is probably
unusually large"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: xlp9xx: Fix case where SSIF read transaction completes early
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix cpumap and devmap on teardown as they're under RCU context
and won't have same assumption as running under NAPI protection,
from Jesper.
2) Fix various sockmap bugs in bpf_tcp_sendmsg() code, e.g. we had
a bug where socket error was not propagated correctly, from Daniel.
3) Fix incompatible libbpf header license for BTF code and match it
before it gets officially released with the rest of libbpf which
is LGPL-2.1, from Martin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Thu, 9 Aug 2018 14:15:54 +0000 (10:15 -0400)]
make sure that __dentry_kill() always invalidates d_seq, unhashed or not
RCU pathwalk relies upon the assumption that anything that changes
->d_inode of a dentry will invalidate its ->d_seq. That's almost
true - the one exception is that the final dput() of already unhashed
dentry does *not* touch ->d_seq at all. Unhashing does, though,
so for anything we'd found by RCU dcache lookup we are fine.
Unfortunately, we can *start* with an unhashed dentry or jump into
it.
We could try and be careful in the (few) places where that could
happen. Or we could just make the final dput() invalidate the damn
thing, unhashed or not. The latter is much simpler and easier to
backport, so let's do it that way.
Reported-by: "Dae R. Jeong" <threeearcat@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Thu, 9 Aug 2018 21:51:32 +0000 (17:51 -0400)]
fix __legitimize_mnt()/mntput() race
__legitimize_mnt() has two problems - one is that in case of success
the check of mount_lock is not ordered wrt preceding increment of
refcount, making it possible to have successful __legitimize_mnt()
on one CPU just before the otherwise final mntpu() on another,
with __legitimize_mnt() not seeing mntput() taking the lock and
mntput() not seeing the increment done by __legitimize_mnt().
Solved by a pair of barriers.
Another is that failure of __legitimize_mnt() on the second
read_seqretry() leaves us with reference that'll need to be
dropped by caller; however, if that races with final mntput()
we can end up with caller dropping rcu_read_lock() and doing
mntput() to release that reference - with the first mntput()
having freed the damn thing just as rcu_read_lock() had been
dropped. Solution: in "do mntput() yourself" failure case
grab mount_lock, check if MNT_DOOMED has been set by racing
final mntput() that has missed our increment and if it has -
undo the increment and treat that as "failure, caller doesn't
need to drop anything" case.
It's not easy to hit - the final mntput() has to come right
after the first read_seqretry() in __legitimize_mnt() *and*
manage to miss the increment done by __legitimize_mnt() before
the second read_seqretry() in there. The things that are almost
impossible to hit on bare hardware are not impossible on SMP
KVM, though...
projects / linux-stable / log