Currently, the CCP driver assumes that the SEV command issued to the PSP
will always return (i.e. it will never hang). But recently, firmware bugs
have shown that a command can hang. Since of the SEV commands are used
in probe routines, this can cause boot hangs and/or loss of virtualization
capabilities.
To protect against firmware bugs, add a timeout in the SEV command
execution flow. If a command does not complete within the specified
timeout then return -ETIMEOUT and stop the driver from executing any
further commands since the state of the SEV firmware is unknown.
Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Gary Hook <Gary.Hook@amd.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: linux-kernel@vger.kernel.org Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[Brijesh: Backported to 4.18..4.19 - offset change in few hunks] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidentally removed the check for negative returns
without considering the issue of type promotion.
The "if_version_length" variable is type size_t so if __mei_cl_recv()
returns a negative then "bytes_recv" is type promoted
to a high positive value and treated as success.
Cc: <stable@vger.kernel.org> Fixes: 582ab27a063a ("mei: bus: fix received data size check in NFC fixup") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When registering clocks, we just skip any that fail to register
(leaving a NULL hole in the clock table). However, our of_xlate
function still tries to dereference each entry while looking for
the clock with the requested id, causing a crash if any clocks
failed to register. Add a check to of_xlate to skip any NULL
clocks.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you do this on an sdm845 board:
grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...
That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE. Oops.
If you do this on an sdm845 board:
cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias bus hold, input bias disabled, input bias pull down, input bias pull up
That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
SCSI probing may synchronously create and destroy a lot of request_queues
for non-existent devices. Any synchronize_rcu() in queue creation or
destroy path may introduce long latency during booting, see detailed
description in comment of blk_register_queue().
This patch removes one synchronize_rcu() inside blk_cleanup_queue()
for this case, commit c2856ae2f315d75(blk-mq: quiesce queue before freeing queue)
needs synchronize_rcu() for implementing blk_mq_quiesce_queue(), but
when queue isn't initialized, it isn't necessary to do that since
only pass-through requests are involved, no original issue in
scsi_execute() at all.
Without this patch and previous one, it may take more 20+ seconds for
virtio-scsi to complete disk probe. With the two patches, the time becomes
less than 100ms.
Fixes: c2856ae2f315d75 ("blk-mq: quiesce queue before freeing queue") Reported-by: Andrew Jones <drjones@redhat.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: linux-scsi@vger.kernel.org Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Tested-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only attempt to merge bio iff the ctx->rq_list isn't empty, because:
1) for high-performance SSD, most of times dispatch may succeed, then
there may be nothing left in ctx->rq_list, so don't try to merge over
sw queue if it is empty, then we can save one acquiring of ctx->lock
2) we can't expect good merge performance on per-cpu sw queue, and missing
one merge on sw queue won't be a big deal since tasks can be scheduled from
one CPU to another.
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
In this case, the affected files are in debugfs (and should therefore only
be accessible to root), and the read handlers check that *pos is zero
(meaning that at least sys_splice() can't trigger kernel memory
corruption). Because of the root requirement, this is not a security fix,
but rather a cleanup.
For the read handlers, fix it by using simple_read_from_buffer() instead
of custom logic. Add min() calls to the write handlers.
Fixes: 4a2da0b8c078 ("IB/mlx5: Add debug control parameters for congestion control") Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warnings in DAC960.c when CONFIG_PROC_FS is not enabled
by marking the unused functions as __maybe_unused.
../drivers/block/DAC960.c:6429:12: warning: 'dac960_proc_show' defined but not used [-Wunused-function]
../drivers/block/DAC960.c:6449:12: warning: 'dac960_initial_status_proc_show' defined but not used [-Wunused-function]
../drivers/block/DAC960.c:6456:12: warning: 'dac960_current_status_proc_show' defined but not used [-Wunused-function]
This patch fixes an issue that unexpected retransfering happens
if TCR is set to 0 before rcar_dmac_sync_tcr() writes DE bit to
the CHCR register. For example, sh-sci driver can reproduce this
issue like below:
In rx_timer_fn(): /* CHCR DE bit may be set to 1 */
dmaengine_tx_status()
rcar_dmac_tx_status()
rcar_dmac_chan_get_residue()
rcar_dmac_sync_tcr() /* TCR is possible to be set to 0 */
According to the description of commit 73a47bd0da66 ("dmaengine:
rcar-dmac: use TCRB instead of TCR for residue"), "this buffered data
will be transferred if CHCR::DE bit was cleared". So, this patch
doesn't need to check TCRB register.
Fixes: 73a47bd0da66 ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm64 PMU updates the event counters and reprograms the
counters in the overflow IRQ handler without disabling the
PMU. This could potentially cause skews in for group counters,
where the overflowed counters may potentially loose some event
counts, while they are reprogrammed. To prevent this, disable
the PMU while we process the counter overflows and enable it
right back when we are done.
This patch also moves the PMU stop/start routines to avoid a
forward declaration.
Suggested-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARRAY_SIZE() macro is type size_t. If s6e8aa0_dcs_read() returns a
negative error code, then "ret < ARRAY_SIZE(id)" is false because the
negative error code is type promoted to a high positive value.
On removal we must free the IRQ *before* cancelling the jack-detect work,
so that the jack-detect work cannot be rescheduled by the IRQ.
Before this commit we were cancelling the jack-detect work from the
driver remove callback, while relying on devm to free the IRQ, which
happens after the remove callback.
This is the wrong order. This commit uses a devm-action to register
a devm callback which cancels the work, before requesting the IRQ
(devm tears things down in reverse order). This also allows us to
remove the now empty remove driver callback.
Cc: Carlo Caione <carlo@endlessm.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the past we've warned when ADJ_OFFSET was in progress, usually
caused by ntpd or some other time adjusting daemon running in non
steady sate, which can cause the skew calculations to be
incorrect.
Thus, this patch checks to see if the clock was being adjusted
when we fail so that we don't cause false negatives.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: linux-kselftest@vger.kernel.org Suggested-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC_MSS_AXIS2 clock is used for disabling boot IMEM (a part of
AP boot up). With Boot IMEM disable now a part TZ/ATF, AXIS2
clock is no longer required post AP boot up and expected to
remain untouched. However if the clock is turned ON after Q6
is brought out of reset and later turned off, it results in
modem hang. When Q6 attempts a power collapse the internal
handshaking to check if AXIS2 is idle never goes through since
it is turned off preventing the RSC from getting triggered,
leaving modem in a funky state. Hence removing AXIS2 clk
enable/disable from the driver.
Kernel occasionally crashed with the following
ops on NVME Target:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffffa042ee50>] lpfc_nvmet_defer_rcv+0x50/0x70 [lpfc]
Callback routine was called for deferred rcv when it should be treated as a
normal rcv.
Added code in callback routine to detect this condition and log a message,
then bail.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fc_rport_login() will be calling mutex_lock() while running inside an
RCU-protected section, triggering the warning 'sleeping function called
from invalid context'. To fix this we can drop the rcu functions here
altogether as the disc mutex protecting the list itself is already held,
preventing any list manipulation.
Fixes: a407c593398c ("scsi: libfc: Fixup disc_mutex handling") Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Johannes Thumshirn <jth@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this commit the following intervals [x y), (x y) were be
replaced to (y-1 y) by snd_interval_refine_last(). This was also done
if y-1 is part of the previous interval.
With this changes it will be replaced with [y-1 y) in case of y-1 is
part of the previous interval. A similar behavior will be used for
snd_interval_refine_first().
This commit adapts the changes for alsa-lib of commit 9bb985c ("pcm: snd_interval_refine_first/last: exclude value only if
also excluded before")
Initialize heap_type to ION_HEAP_TYPE_SYSTEM to avoid "used uninitialized"
compiler warning. heap_type gets used after initialization, this change is
to just keep the compiler happy.
root@vm-lkp-nex04-8G-7 ~/linux-v4.18-rc2/tools/testing/selftests/android# make
make[1]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
make[1]: Entering directory '/root/linux-v4.18-rc2/tools/testing/selftests/android/ion'
gcc -I. -I../../../../../drivers/staging/android/uapi/ -I../../../../../usr/include/ -Wall -O2 -g ionapp_export.c ipcsocket.c ionutils.c -o ionapp_export
ionapp_export.c: In function 'main':
ionapp_export.c:91:2: warning: 'heap_type' may be used uninitialized in
this function [-Wmaybe-uninitialized]
printf("heap_type: %ld, heap_size: %ld\n", heap_type, heap_size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Return ERR_PTR(-EINVAL) if kfd_get_process fails to find the process.
This fixes kernel oopses when a child process calls KFD ioctls with
a file descriptor inherited from the parent process.
Signed-off-by: Wei Lu <wei.lu2@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The get_seconds() call is deprecated because it overflows on 32-bit
architectures. The algorithm in rcu_torture_stall() can deal with
the overflow, but another problem here is that using a CLOCK_REALTIME
stamp can lead to a false-positive stall warning when a settimeofday()
happens concurrently.
Using ktime_get_seconds() instead avoids those issues and will never
overflow. The added cast to 'unsigned long' however is necessary to
make ULONG_CMP_LT() work correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPv2 driver defines 2 "queue_modes" :
- QDIST_SINGLE_MODE, where each port share one rx queue vector
between all CPUs
- QDIST_MULTI_MODE, where each port has one rx queue vector per CPU.
Multi queue mode isn't available on PPv2.1, make sure we fallback to
single mode when running on this revision.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code was not tested with two ports actually in use at
the same time. (I blame this on lack of actual hardware using
that feature.) Now after locating a system using both ports,
add necessary fix to make both ports come up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.
Mark gpio_suffixes array with __maybe_unused to hide a compiler warning:
In file included from
drivers/gpio/gpiolib-legacy.c:6:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
static const char * const gpio_suffixes[] = { "gpios", "gpio" };
^~~~~~~~~~~~~
In file included from drivers/gpio/gpiolib-devprop.c:17:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
static const char * const gpio_suffixes[] = { "gpios", "gpio" };
^~~~~~~~~~~~~
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
When recovering a line, an extra check was added when debugging was
active, such that minor version where also checked. Unfortunately,
this used the ifdef NVM_DEBUG, which is not correct.
Instead use the proper DEBUG def, and now that it compiles, also fix
the variable.
Signed-off-by: Matias Bjørling <mb@lightnvm.io> Fixes: d0ab0b1ab991f ("lightnvm: pblk: check data lines version on recovery") Reviewed-by: Javier González <javier@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main thing is that the data->priv[] array has AFE_PORT_MAX elements
so the > condition should be >=. But we may as well check for negative
values as well just to be safe.
Fixes: 24c4cbcfac09 ("ASoC: qdsp6: q6afe: Add q6afe dai driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Megachip dockings accesses ddc line through display driver when
installing FW. Previously, we would fail every transaction because
link attached to mst branch did not have their ddc transaction type
set.
[How]
Set ddc transaction type when mst branch is connected.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Probing the TPIU driver under UBSan triggers an out-of-bounds shift
warning in coresight_timeout():
...
[ 5.677530] UBSAN: Undefined behaviour in drivers/hwtracing/coresight/coresight.c:929:16
[ 5.685542] shift exponent 64 is too large for 64-bit type 'long unsigned int'
...
On closer inspection things are exponentially out of whack because we're
passing a bitmask where a bit number should be. Amusingly, it seems that
both calls will find their expected values by sheer luck and appear to
succeed: 1 << FFCR_FON_MAN ends up at bit 64 which whilst undefined
evaluates as zero in practice, while 1 << FFSR_FT_STOPPED finds bit 2
(TCPresent) which apparently is usually tied high.
Following the examples of other drivers, define separate FOO and FOO_BIT
macros for masks vs. indices, and put things right.
CC: Robert Walker <robert.walker@arm.com> CC: Mike Leach <mike.leach@linaro.org> CC: Mathieu Poirier <mathieu.poirier@linaro.org> Fixes: 11595db8e17f ("coresight: Fix disabling of CoreSight TPIU") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new task wakes-up for the first time, its initial utilization
is set to half of the spare capacity of its CPU. The current
implementation of post_init_entity_util_avg() uses SCHED_CAPACITY_SCALE
directly as a capacity reference. As a result, on a big.LITTLE system, a
new task waking up on an idle little CPU will be given ~512 of util_avg,
even if the CPU's capacity is significantly less than that.
Fix this by computing the spare capacity with arch_scale_cpu_capacity().
zerocopy_from_iter iterates over the message, but it doesn't revert the
updates made by the iov iteration. This patch fixes it. Now, the iov can
be used after calling zerocopy_from_iter.
Fixes: 3c4d75591 ("tls: kernel TLS support") Signed-off-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the kernel configuration, early ARM architecture setup code
may have attached the GPU to a DMA/IOMMU mapping that transparently uses
the IOMMU to back the DMA API. Tegra requires special handling for IOMMU
backed buffers (a special bit in the GPU's MMU page tables indicates the
memory path to take: via the SMMU or directly to the memory controller).
Transparently backing DMA memory with an IOMMU prevents Nouveau from
properly handling such memory accesses and causes memory access faults.
As a side-note: buffers other than those allocated in instance memory
don't need to be physically contiguous from the GPU's perspective since
the GPU can map them into contiguous buffers using its own MMU. Mapping
these buffers through the IOMMU is unnecessary and will even lead to
performance degradation because of the additional translation. One
exception to this are compressible buffers which need large pages. In
order to enable these large pages, multiple small pages will have to be
combined into one large (I/O virtually contiguous) mapping via the
IOMMU. However, that is a topic outside the scope of this fix and isn't
currently supported. An implementation will want to explicitly create
these large pages in the Nouveau driver, so detaching from a DMA/IOMMU
mapping would still be required.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Tested-by: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes various reclocking related issues on prime systems.
Signed-off-by: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed this as I was skimming through, if we fail to allocate memory
for cli we'll end up returning without dropping the runtime PM ref we
got. Additionally, we'll even return the wrong return code! (ret most
likely will == 0 here, we want -ENOMEM).
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
mmc1: Switching to 3.3V signalling voltage failed
Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.
The stack assumes that SDHC controller which support SD3.0 (SDR104) do
support HS200. This is not the case for Tegra 3, which does support SD
3.0
but only supports eMMC spec 4.41.
Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not
support HS200.
Note that commit 156e14b126ff ("mmc: sdhci: fix caps2 for HS200") added
the tie between SD3.0 (SDR104) and HS200. I don't think that this is
necessarly true. It is fully legitimate to support SD3.0 and not support
HS200. The quirk naming suggests something is broken in the controller,
but this is not the case: The controller simply does not support HS200.
SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
When the termios CIBAUD bits are left unset (i.e. B0), we use the same
output and input speed and should leave CIBAUD unchanged.
When the user requests a rate using BOTHER and c_ospeed which the driver
cannot set exactly, the driver can report back the actual baud rate
using tty_termios_encode_baud_rate(). If this rate is close enough to a
standard rate however, we could end up setting CIBAUD to a Bfoo value
despite the user having left it unset.
This in turn could lead to an unexpected input rate being set on
subsequent termios updates.
Fix this by using a zero tolerance value also for the input rate when
CIBAUD is clear so that the matching logic works as expected.
Commit 943fa0228252 ("ASoC: hdmi-codec: Use different name for playback
streams") broke hdmi-codec's routing between it's output "TX" widget
and the S/PDIF or I2S streams by renaming the streams.
Whether an error occurs or not is dependent on whether there is another
widget called "Playback" registered by some other component - if there
is, that widget will be (incorrectly) bound to the HDMI codec's "TX"
output widget. If we end up connecting "TX" incorrectly, it can result
in components not being started, causing no audio output.
Since the I2S and S/PDIF streams now have different names, we can't
use a static route at component level to describe the relationship, so
arrange to dynamically create the route when the DAI driver is probed.
Fixes: 943fa0228252 ("ASoC: hdmi-codec: Use different name for playback streams") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring SLI_PKTn_OUTPUT_CONTROL, VF driver was assuming that IPTR
mode was disabled by reset, which was not true. Since DPDK driver had
set IPTR mode previously, the VF driver (which uses buf-ptr-only mode) was
not properly handling DROQ packets (i.e. it saw zero-length packets).
This represented an invalid hardware configuration which the driver could
not handle.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_compatible_node() returns a device node with refcount incremented
and thus needs an explicit of_node_put(). Further relying on an unchecked
of_iomap() which can return NULL is problematic here, after all ctrl_base
is critical enough for hix5hd2_set_cpu() to call BUG() if not available
so a check seems mandated here.
When doing reset, netdev has not been brought up is not an error,
it means that we do not need do the stop operation, so just return
zero.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_iomap() can return NULL which seems critical here and thus should be
explicitly flagged so that the cause of system halting can be understood.
As of_find_compatible_node() is returning a device node with refcount
incremented it must be explicitly decremented here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit 7fda91e73155 ("ARM: hisi: enable smp for HiP01") Signed-off-by: Wei Xu <xuwei5@hisilicon.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relying on an unchecked of_iomap() which can return NULL is problematic
here, an explicit check seems mandatory. Also the call to
of_find_compatible_node() returns a device node with refcount incremented
therefor an explicit of_node_put() is needed here.
handle->reset_level is assigned to HNAE3_NONE_RESET when client is
initialized, if a tx timeout happens right after initialization,
then handle->reset_level is not resetted to HNAE3_FUNC_RESET in
hclge_reset_event, which will cause reset event not properly
handled problem.
This patch fixes it by setting handle->reset_level properly when
client is initialized.
Fixes: 6d4c3981a8d8 ("net: hns3: Changes to make enet watchdog timeout func common for PF/VF") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since current locking was not covering certain code where
netdev was being accessed or manipulated, this patch fixes
it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
7e1550b8f208 ("efi: Drop type and attribute checks in efi_mem_desc_lookup()")
refactored the implementation of efi_mem_desc_lookup() so that the type
check is moved to the callers, one of which is the x86 version of
efi_arch_mem_reserve(), where we added a modified check that only takes
EFI_BOOT_SERVICES_DATA regions into account.
This is reasonable, since it is the only memory type that requires this,
but doing so uncovered some unexpected behavior in the ESRT code, which
permits the ESRT table to reside in other types of memory than what the
UEFI spec mandates (i.e., EFI_BOOT_SERVICES_DATA), and unconditionally
calls efi_mem_reserve() on the region in question. This may result in
errors such as
esrt: Reserving ESRT space from 0x000000009c810318 to 0x000000009c810350.
efi: Failed to lookup EFI memory descriptor for 0x000000009c810318
when the ESRT table is not in EFI_BOOT_SERVICES_DATA memory, but we try
to reserve it nonetheless.
So make the call to efi_mem_reserve() conditional on the memory type.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit replaces the above smp_wmb() with an smp_mb() in order to
guarantee that either wait_woken() sees the wait condition being true
or the store to wq_entry->flags in woken_wake_function() follows the
store in wait_woken() in the coherence order (so that the former can
eventually be observed by wait_woken()).
The commit also fixes a comment associated to set_current_state() in
wait_woken(): the comment pairs the barrier in set_current_state() to
the above smp_wmb(), while the actual pairing involves the barrier in
set_current_state() and the barrier executed by the try_to_wake_up()
in wake_woken_function().
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: akiyks@gmail.com Cc: boqun.feng@gmail.com Cc: dhowells@redhat.com Cc: j.alglave@ucl.ac.uk Cc: linux-arch@vger.kernel.org Cc: luc.maranget@inria.fr Cc: npiggin@gmail.com Cc: parri.andrea@gmail.com Cc: stern@rowland.harvard.edu Cc: will.deacon@arm.com Link: http://lkml.kernel.org/r/20180716180605.16115-10-paulmck@linux.vnet.ibm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must use a mutex around the generic_add functions and save the
function and group selector in case we need to remove them. Otherwise
the selector use will be racy for deferred probe at least.
Fixes: 5a49b644b307 ("pinctrl: Renesas RZ/A1 pin and gpio controller") Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: Christ van Willegen <cvwillegen@gmail.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Paul Cercueil <paul@crapouillou.net> Cc: Sean Wang <sean.wang@mediatek.com> Acked-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-By: H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit acf137951367 ("pinctrl: core: Return selector to the
pinctrl driver") and the commit 47f1242d19c3 ("pinctrl: pinmux: Return
selector to the pinctrl driver"), it's necessary to add the fixes
needed for the pin controller drivers to use the appropriate returned
selector for a negative error number returned in case of the fail at
these functions. Otherwise, the driver would have a failed probe and
that causes boot message cannot correctly output and devices fail
to acquire their own pins.
Cc: Kevin Hilman <khilman@baylibre.com> Fixes: acf137951367 ("pinctrl: core: Return selector to the pinctrl driver") Fixes: 47f1242d19c3 ("pinctrl: pinmux: Return selector to the pinctrl driver") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug where configfs_register_group had added
a group in a tree, and userspace has done a rmdir on a dir somewhere
above that group and we hit a kernel crash. The problem is configfs_rmdir
will detach everything under it and unlink groups on the default_groups
list. It will not unlink groups added with configfs_register_group so when
configfs_unregister_group is called to drop its references to the group/items
we crash when we try to access the freed dentrys.
The patch just adds a check for if a rmdir has been done above
us and if so just does the unlink part of unregistration.
Sorry if you are getting this multiple times. I thouhgt I sent
this to some of you and lkml, but I do not see it.
Signed-off-by: Mike Christie <mchristi@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching a hardware table to LIOBN in KVM, we match table parameters
such as page size, table offset and table size. However the tables are
created via very different paths - VFIO and KVM - and the VFIO path goes
through the platform code which has minimum TCE page size requirement
(which is 4K but since we allocate memory by pages and cannot avoid
alignment anyway, we align to 64k pages for powernv_defconfig).
So when we match the tables, one might be bigger that the other which
means the hardware table cannot get attached to LIOBN and DMA mapping
fails.
This removes the table size alignment from the guest visible table.
This does not affect the memory allocation which is still aligned -
kvmppc_tce_pages() takes care of this.
This relaxes the check we do when attaching tables to allow the hardware
table be bigger than the guest visible table.
Ideally we want the KVM table to cover the same space as the hardware
table does but since the hardware table may use multiple levels, and
all levels must use the same table size (IODA2 design), the area it can
actually cover might get very different from the window size which
the guest requested, even though the guest won't map it all.
Never directly free @dev after calling device_register() or
device_unregister(), even if device_register() returned an error.
Always use put_device() to give up the reference initialized.
The call to of_find_compatible_node() is returning a pointer with
incremented refcount so it must be explicitly decremented after the
last use. As here it is only being used for checking of node presence
but the result is not actually used in the success path it can be
dropped immediately.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit f725758b899f ("KVM: PPC: Book3S HV: Use OPAL XICS emulation on POWER9") Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When EVM attempts to appraise a file signed with a crypto algorithm the
kernel doesn't have support for, it will cause the kernel to trigger a
module load. If the EVM policy includes appraisal of kernel modules this
will in turn call back into EVM - since EVM is holding a lock until the
crypto initialisation is complete, this triggers a deadlock. Add a
CRYPTO_NOLOAD flag and skip module loading if it's set, and add that flag
in the EVM case in order to fail gracefully with an error message
instead of deadlocking.
Signed-off-by: Matthew Garrett <mjg59@google.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to get an interrupt as soon as it is requested. dw_spi_irq
does spi_controller_get_devdata(master) and expects it to be different than
NULL. However, spi_controller_set_devdata() is called after request_irq(),
resulting in the following crash:
CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90
[...]
Call Trace:
[<8058e09c>] dw_spi_irq+0x8/0x64
[<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4
[<80190128>] handle_irq_event_percpu+0x34/0x8c
[<801901c4>] handle_irq_event+0x44/0x80
[<801951a8>] handle_level_irq+0xdc/0x194
[<8018f580>] generic_handle_irq+0x38/0x50
[<804c6924>] ocelot_irq_handler+0x104/0x1c0
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The progs local variable in compute_effective_progs() is marked
as __rcu, which is not correct. This is a local pointer, which
is initialized by bpf_prog_array_alloc(), which also now
returns a generic non-rcu pointer.
The real rcu-protected pointer is *array (array is a pointer
to an RCU-protected pointer), so the assignment should be performed
using rcu_assign_pointer().
Fixes: 324bda9e6c5a ("bpf: multi program support for cgroup+bpf") Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The underlying real file used by overlayfs still contains the overlay path.
This results in mnt_want_write_file() calls by the filesystem getting
freeze protection on the wrong inode (the overlayfs one instead of the real
one).
Fix by using file_inode(file)->i_sb instead of file->f_path.mnt->mnt_sb.
Reported-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first checks in mtdchar_read() and mtdchar_write() attempt to limit
`count` such that `*ppos + count <= mtd->size`. However, they ignore the
possibility of `*ppos > mtd->size`, allowing the calculation of `count` to
wrap around. `mtdchar_lseek()` prevents seeking beyond mtd->size, but the
pread/pwrite syscalls bypass this.
I haven't found any codepath on which this actually causes dangerous
behavior, but it seems like a sensible change anyway.
audit_add_watch stores locally krule->watch without taking a reference
on watch. Then, it calls audit_add_to_parent, and uses the watch stored
locally.
Unfortunately, it is possible that audit_add_to_parent updates
krule->watch.
When it happens, it also drops a reference of watch which
could free the watch.
The second call to auditctl triggers the use-after-free, because
audit_to_parent updates krule->watch to use a previous existing watch
and drops the reference to the newly created watch.
To fix the issue, we grab a reference of watch and we release it at the
end of the function.
Signed-off-by: Ronny Chevalier <ronny.chevalier@hp.com> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
The regset API documented in <linux/regset.h> defines -ENODEV as the
result of the `->active' handler to be used where the feature requested
is not available on the hardware found. However code handling core file
note generation in `fill_thread_core_info' interpretes any non-zero
result from the `->active' handler as the regset requested being active.
Consequently processing continues (and hopefully gracefully fails later
on) rather than being abandoned right away for the regset requested.
Fix the problem then by making the code proceed only if a positive
result is returned from the `->active' handler.
Signed-off-by: Maciej W. Rozycki <macro@mips.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 4206d3aa1978 ("elf core dump: notes user_regset")
Patchwork: https://patchwork.linux-mips.org/patch/19332/ Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-fsdevel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Cc: stable <stable@vger.kernel.org> # 4.15 Cc: Carlo Caione <carlo@endlessm.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add of_get_compatible_child() helper that can be used to lookup
compatible child nodes.
Several drivers currently use of_find_compatible_node() to lookup child
nodes while failing to notice that the of_find_ functions search the
entire tree depth-first (from a given start node) and therefore can
match unrelated nodes. The fact that these functions also drop a
reference to the node they start searching from (e.g. the parent node)
is typically also overlooked, something which can lead to use-after-free
bugs.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous fix broke recovery of delegated stateids because it assumes
that if we did not mark the delegation as suspect, then the delegation has
effectively been revoked, and so it removes that delegation irrespectively
of whether or not it is valid and still in use. While this is "mostly
harmless" for ordinary I/O, we've seen pNFS fail with LAYOUTGET spinning
in an infinite loop while complaining that we're using an invalid stateid
(in this case the all-zero stateid).
What we rather want to do here is ensure that the delegation is always
correctly marked as needing testing when that is the case. So we want
to close the loophole offered by nfs4_schedule_stateid_recovery(),
which marks the state as needing to be reclaimed, but not the
delegation that may be backing it.
With commit 0b3ce78e90fc ("of: cache phandle nodes to reduce cost of
of_find_node_by_phandle()"), a G3 PowerMac fails to boot. The root cause
is the DT for this system has no phandle properties when booted with
BootX. of_populate_phandle_cache() does not handle the case of no
phandles correctly. The problem is roundup_pow_of_two() for 0 is
undefined. The implementation subtracts 1 underflowing and then things
are in the weeds.
Fixes: 0b3ce78e90fc ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()") Cc: stable@vger.kernel.org # 4.17+ Reported-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Reviewed-by: Frank Rowand <frank.rowand@sony.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1c5aae7710bb ("perf machine: Create maps for x86 PTI entry
trampolines") revealed a problem with maps__find_symbol_by_name() that
resulted in probes not being found e.g.
$ sudo perf probe xsk_mmap
xsk_mmap is out of .text, skip it.
Probe point 'xsk_mmap' not found.
Error: Failed to add events.
maps__find_symbol_by_name() can optionally return the map of the found
symbol. It can get the map wrong because, in fact, the symbol is found
on the map's dso, not allowing for the possibility that the dso has more
than one map. Fix by always checking the map contains the symbol.
Reported-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Björn Töpel <bjorn.topel@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 1c5aae7710bb ("perf machine: Create maps for x86 PTI entry trampolines") Link: http://lkml.kernel.org/r/20180907085116.25782-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perf can record user stack data in response to a synchronous request, such
as a tracepoint firing. If this happens under set_fs(KERNEL_DS), then we
end up reading user stack data using __copy_from_user_inatomic() under
set_fs(KERNEL_DS). I think this conflicts with the intention of using
set_fs(KERNEL_DS). And it is explicitly forbidden by hardware on ARM64
when both CONFIG_ARM64_UAO and CONFIG_ARM64_PAN are used.
So fix this by forcing USER_DS when recording user stack data.
Signed-off-by: Yabin Cui <yabinc@google.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 88b0193d9418 ("perf/callchain: Force USER_DS when invoking perf_callchain_user()") Link: http://lkml.kernel.org/r/20180823225935.27035-1-yabinc@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "le32_to_cpu(rsp->OutputOffset) + *plen" addition can overflow and
wrap around to a smaller value which looks like it would lead to an
information leak.
Fixes: 4a72dafa19ba ("SMB2 FSCTL and IOCTL worker function") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that "entryptr + next_offset" and "entryptr + len + size"
can wrap. I ended up changing the type of "entryptr" because it makes
the math easier when we don't have to do so much casting.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "old_entry + le32_to_cpu(pDirInfo->NextEntryOffset)" can wrap
around so I have added a check for integer overflow.
Reported-by: Dr Silvio Cesare of InfoSect <silvio.cesare@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.
Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.
I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.
A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.
Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.
After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.
As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.
When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().
As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).
wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
projects / linux-stable / log