[subject was: drm/msm: shake fist angrily at dma-mapping]
So, using dma_sync_* for our cache needs works out w/ dma iommu ops, but
it falls appart with dma direct ops. The problem is that, depending on
display generation, we can have either set of dma ops (mdp4 and dpu have
iommu wired to mdss node, which maps to toplevel drm device, but mdp5
has iommu wired up to the mdp sub-node within mdss).
Fixes: 0036bc73ccbe (drm/msm: stop abusing dma_map/unmap for cache) Fixes: 449fa54d6815 (dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device) Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Rob Clark <robdclark@chromium.org>
[seanpaul changed subject to something more desriptive] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190730214633.17820-1-robdclark@gmail.com Cc: nobuhiro1.iwamatsu@toshiba.co.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts
commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for the chunk sizes coming from the non RPM remote procs
to not be word aligned. Remove the alignment warning and continue to
read from the FIFO so execution is not stalled.
Signed-off-by: Chris Lew <clew@codeaurora.org> Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__early_cpu_boot_status is of type long. Use quad
assembler directive to allocate proper size.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Arun KS <arunks@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not quite sure what triggered that, but we really shouldn't be abusing
dma_{map,unmap}_sg() for cache maint.
Cc: Stephen Boyd <sboyd@kernel.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190630124735.27786-1-robdclark@gmail.com Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lock ordering only happens when bonding is enabled and a certain
bonding related event fires. However, since it can happen this is a global
restriction on lock ordering.
Teach lockdep about the order directly and unconditionally so bugs here
are found quickly.
This appears to be a bug in the design, as it does have lots of locking
that seems like it should allow concurrency. However, when it is all said
and done every single place that uses the cma_exch() scheme is broken, and
all the unlocked reads from the ucma of the cm_id data are wrong too.
syzkaller has been finding endless bugs related to this.
Fixing this in any elegant way is some enormous amount of work. Take a
very big hammer and put a mutex around everything to do with the
ucma_context at the top of every syscall.
syzbot reported that 4fbc0c711b24 ("ceph: remove the extra slashes in
the server path") had caused a regression where an allocation could be
done under a spinlock -- compare_mount_options() is called by sget_fc()
with sb_lock held.
We don't really need the supplied server path, so canonicalize it
in place and compare it directly. To make this work, the leading
slash is kept around and the logic in ceph_real_mount() to skip it
is restored. CEPH_MSG_CLIENT_SESSION now reports the same (i.e.
canonicalized) path, with the leading slash of course.
Fixes: 4fbc0c711b24 ("ceph: remove the extra slashes in the server path") Reported-by: syzbot+98704a51af8e3d9425a9@syzkaller.appspotmail.com Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And then when creating any new file or directory under the mount
point, we can hit the following BUG_ON in ceph_fill_trace():
BUG_ON(ceph_snap(dir) != dvino.snap);
Have the client ignore the extra slashes in the server path when
mounting. This will also canonicalize the path, so that identical mounts
can be consilidated.
Regardless of the internal treatment of these paths, the kernel still
stores the original string including the leading '/' for presentation
to userland.
URL: https://tracker.ceph.com/issues/42771 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Releasing dd->per_sdma[i].kobject in hfi1_unregister_sysfs().
- This will fix the memory leak.
- Calling kobject_put() to unwind operations only for those entries in
dd->per_sdma[] whose operations have succeeded (including the current
one that has just failed) in hfi1_verbs_register_sysfs().
Cc: <stable@vger.kernel.org> Fixes: 0cb2aa690c7e ("IB/hfi1: Add sysfs interface for affinity setup") Link: https://lore.kernel.org/r/20200326163807.21129.27371.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kobject_init_and_add() returns an error in the function
hfi1_create_port_files(), the function kobject_put() is not called for the
corresponding kobject, which potentially leads to memory leak.
This patch fixes the issue by calling kobject_put() even if
kobject_init_and_add() fails.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326163813.21129.44280.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the rngc interrupt is masked if the rngc self test fails.
Self test failure means that probe fails as well. Interrupts should be
masked in this case, regardless of the error.
Cc: stable@vger.kernel.org Fixes: 1d5449445bd0 ("hwrng: mx-rngc - add a driver for Freescale RNGC") Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Signed-off-by: Martin Kaiser <martin@kaiser.cx> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change to the netlink code: 6e237d099fac ("netlink: Relax attr
validation for fixed length types") logs a warning when programs send
messages with invalid attributes (e.g., wrong length for a u32). Yafang
reported this error message for tools/accounting/getdelays.c.
send_cmd() is wrongly adding 1 to the attribute length. As noted in
include/uapi/linux/netlink.h nla_len should be NLA_HDRLEN + payload
length, so drop the +1.
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
It turns out that RDRAND is pretty slow. Comparing these two
constructions:
for (i = 0; i < CHACHA_BLOCK_SIZE; i += sizeof(ret))
arch_get_random_long(&ret);
and
long buf[CHACHA_BLOCK_SIZE / sizeof(long)];
extract_crng((u8 *)buf);
it amortizes out to 352 cycles per long for the top one and 107 cycles
per long for the bottom one, on Coffee Lake Refresh, Intel Core i9-9880H.
And importantly, the top one has the drawback of not benefiting from the
real rng, whereas the bottom one has all the nice benefits of using our
own chacha rng. As get_random_u{32,64} gets used in more places (perhaps
beyond what it was originally intended for when it was introduced as
get_random_{int,long} back in the md5 monstrosity era), it seems like it
might be a good thing to strengthen its posture a tiny bit. Doing this
should only be stronger and not any weaker because that pool is already
initialized with a bunch of rdrand data (when available). This way, we
get the benefits of the hardware rng as well as our own rng.
Another benefit of this is that we no longer hit pitfalls of the recent
stream of AMD bugs in RDRAND. One often used code pattern for various
things is:
do {
val = get_random_u32();
} while (hash_table_contains_key(val));
That recent AMD bug rendered that pattern useless, whereas we're really
very certain that chacha20 output will give pretty distributed numbers,
no matter what.
So, this simplification seems better both from a security perspective
and from a performance perspective.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200221201037.30231-1-Jason@zx2c4.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handler for FLOW_ACTION_VLAN_MANGLE ends by returning whatever the
lower-level function that it calls returns. If there are more actions lined
up after this action, those are never offloaded. Fix by only bailing out
when the called function returns an error.
Fixes: a150201a70da ("mlxsw: spectrum: Add support for vlan modify TC action") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Fixes: a1044e36e457 ("can: add slcan driver for serial/USB-serial CAN adapters") Reviewed-by: Kees Cook <keescook@chromium.org> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: security@kernel.org Cc: wg@grandegger.com Cc: mkl@pengutronix.de Cc: davem@davemloft.net Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address entries") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were registering our slave MDIO bus with OF and doing so with
assigning the newly created slave_mii_bus of_node to the master MDIO bus
controller node. This is a bad thing to do for a number of reasons:
- we are completely lying about the slave MII bus is arranged and yet we
still want to control which MDIO devices it probes. It was attempted
before to play tricks with the bus_mask to perform that:
https://www.spinics.net/lists/netdev/msg429420.html but the approach
was rightfully rejected
- the device_node reference counting is messed up and we are effectively
doing a double probe on the devices we already probed using the
master, this messes up all resources reference counts (such as clocks)
The proper fix for this as indicated by David in his reply to the
thread above is to use a platform data style registration so as to
control exactly which devices we probe:
https://www.spinics.net/lists/netdev/msg430083.html
By using mdiobus_register(), our slave_mii_bus->phy_mask value is used
as intended, and all the PHY addresses that must be redirected towards
our slave MDIO bus is happening while other addresses get redirected
towards the master MDIO bus.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bonding slave and team port devices should not have link-local addresses
automatically added to them, as it can interfere with openvswitch being
able to properly add tc ingress.
Basic reproducer, courtesy of Marcelo:
$ ip link add name bond0 type bond
$ ip link set dev ens2f0np0 master bond0
$ ip link set dev ens2f1np2 master bond0
$ ip link set dev bond0 up
$ ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link
valid_lft forever preferred_lft forever
$ ip a l ens2f0np0
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
$ ip a l ens2f1np2
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is
this a slave interface?" check added by commit c2edacf80e15, and
results in an address getting added, while w/the proposed patch added,
no address gets added. This simply adds the same gating check to another
code path, and thus should prevent the same devices from erroneously
obtaining an ipv6 link-local address.
Fixes: d35a00b8e33d ("net/ipv6: allow sysctl to change link-local address generation mode") Reported-by: Moshe Levi <moshele@mellanox.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ctags indexing ("make tags" command) throws this warning:
ctags: Warning: include/linux/notifier.h:125:
null expansion of name pattern "\1"
This is the result of DEFINE_PER_CPU() macro expansion. Fix that by
getting rid of line break.
Similar fix was already done in commit 25528213fe9f ("tags: Fix
DEFINE_PER_CPU expansions"), but this one probably wasn't noticed.
Link: http://lkml.kernel.org/r/20181030202808.28027-1-semen.protsenko@linaro.org Fixes: 9c80172b902d ("kernel/SRCU: provide a static initializer") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
======================================================
WARNING: possible circular locking dependency detected
5.4.0-rc8-padata-cpuhp-v3+ #1 Not tainted
------------------------------------------------------
bash/205 is trying to acquire lock: ffffffff8286bcd0 (cpu_hotplug_lock.rw_sem){++++}, at: padata_set_cpumask+0x2b/0x120
but task is already holding lock: ffff8880001abfa0 (&pinst->lock){+.+.}, at: padata_set_cpumask+0x26/0x120
which lock already depends on the new lock.
padata doesn't take cpu_hotplug_lock and pinst->lock in a consistent
order. Which should be first? CPU hotplug calls into padata with
cpu_hotplug_lock already held, so it should have priority.
Fixes: 6751fb3c0e0c ("padata: Use get_online_cpus/put_online_cpus") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the lower and upper bounds when there are multiple TCs and
traffic is on the the same TC on the same device.
The lower bound is represented by 'qoffset' and the upper limit for
hash value is 'qcount + qoffset'. This gives a clean Rx to Tx queue
mapping when there are multiple TCs, as the queue indices for upper TCs
will be offset by 'qoffset'.
v2: Fixed commit description based on comments.
Fixes: 1b837d489e06 ("net: Revoke export for __skb_tx_hash, update it to just be static skb_tx_hash") Fixes: eadec877ce9c ("net: Add support for subordinate traffic classes to netdev_pick_tx") Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the handling of sendmsg() with MSG_WAITALL for userspace to round the
timeout for when a signal occurs up to at least two jiffies as a 1 jiffy
timeout may end up being effectively 0 if jiffies wraps at the wrong time.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a system which has an EVGA X99 Classified motherboard. The pin
assignments for the HD Audio controller are not correct under Linux.
Windows 10 works fine and informs me that it's using the Recon3Di
driver, and on Linux, `cat
/sys/class/sound/card0/device/subsystem_{vendor,device}` yields
0x3842
0x1038
This patch adds a corresponding entry to the quirk list.
Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.
The native drivers mostly work fine, but there are 2 problems:
1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.
So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.
Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.
2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.
The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.
Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.
This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.
So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.
If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.
OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On devices with an AXP288, we need to wakeup from suspend when a charger
is plugged in, so that we can do charger-type detection and so that the
axp288-charger driver, which listens for our extcon events, can configure
the input-current-limit accordingly.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIT() macro definition is not available for the UAPI headers
(moreover, it can be defined differently in the user space); replace
its usage with the _BITUL() macro that is defined in <linux/const.h>.
commit e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands")
uses module parameter 'irqtype' in pci_endpoint_test_set_irq()
to check if IRQ vectors of a particular type (MSI or MSI-X or
LEGACY) is already allocated. However with multi-function devices,
'irqtype' will not correctly reflect the IRQ type of the PCI device.
Fix it here by adding 'irqtype' for each PCI device to show the
IRQ type of a particular PCI device.
Fixes: e03327122e2c ("pci_endpoint_test: Add 2 ioctl commands") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding more than 10 pci-endpoint-test devices results in
"kobject_add_internal failed for pci-endpoint-test.1 with -EEXIST, don't
try to register things with the same name in the same directory". This
is because commit 2c156ac71c6b ("misc: Add host side PCI driver for PCI
test function device") limited the length of the "name" to 20 characters.
Change the length of the name to 24 in order to support upto 10000
pci-endpoint-test devices.
Fixes: 2c156ac71c6b ("misc: Add host side PCI driver for PCI test function device") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a MMU is shared between multiple GPUs, all of them need to flush their
TLBs, so a single marker that gets reset on the first flush won't do.
Replace the flush marker with a sequence number, so that it's possible to
check if the TLB is in sync with the current page table state for each GPU.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Chromebook BIOS' do not export an ACPI LPIT, which is how
Linux finds the residency counter for CPU and SYSTEM low power states,
that is exports in /sys/devices/system/cpu/cpuidle/*residency_us
When these sysfs attributes are missing, check the debugfs attrubte
from the pmc_core driver, which accesses the same counter value.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even though INITRAMFS_SOURCE kconfig option isn't set in most of
defconfigs it is used (set) extensively by various build systems.
Commit f26661e12765 ("initramfs: make initramfs compression choice
non-optional") has changed default compression mode. Previously we
compress initramfs using available compression algorithm. Now
we don't use any compression at all by default.
It significantly increases the image size in case of build system
chooses embedded initramfs. Initially I faced with this issue while
using buildroot.
As of today it's not possible to set preferred compression mode
in target defconfig as this option depends on INITRAMFS_SOURCE
being set. Modification of all build systems either doesn't look
like good option.
Let's instead rewrite initramfs compression mode choices list
the way that "INITRAMFS_COMPRESSION_NONE" will be the last option
in the list. In that case it will be chosen only if all other
options (which implements any compression) are not available.
Shutdown of firmware framebuffer has a bunch of problems. Because
of this the framebuffer region might still be reserved even after
drm_fb_helper_remove_conflicting_pci_framebuffers() returned.
Don't consider pci_request_region() failure for the framebuffer
region as fatal error to workaround this issue.
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The timeout of identify cmd, which is invoked as part of admin queue
creation, can result in freeing of async event data both in
nvme_rdma_timeout handler and error handling path of
nvme_rdma_configure_admin queue thus causing NULL pointer reference.
Call Trace:
? nvme_rdma_setup_ctrl+0x223/0x800 [nvme_rdma]
nvme_rdma_create_ctrl+0x2ba/0x3f7 [nvme_rdma]
nvmf_dev_write+0xa54/0xcc6 [nvme_fabrics]
__vfs_write+0x1b/0x40
vfs_write+0xb2/0x1b0
ksys_write+0x61/0xd0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x60/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reviewed-by: Roland Dreier <roland@purestorage.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under certain circumstances, depending on the order of addresses on the
interfaces, it could be that sctp_v[46]_get_dst() would return a dst
with a mismatched struct flowi.
For example, if when walking through the bind addresses and the first
one is not a match, it saves the dst as a fallback (added in 410f03831c07), but not the flowi. Then if the next one is also not a
match, the previous dst will be returned but with the flowi information
for the 2nd address, which is wrong.
The fix is to use a locally stored flowi that can be used for such
attempts, and copy it to the parameter only in case it is a possible
match, together with the corresponding dst entry.
The patch updates IPv6 code mostly just to be in sync. Even though the issue
is also present there, it fallback is not expected to work with IPv6.
Fixes: 410f03831c07 ("sctp: add routing output fallback") Reported-by: Jin Meng <meng.a.jin@nokia-sbell.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Tested-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should iterate over the datamsgs to move
all chunks(skbs) to newsk.
The following case cause the bug:
for the trouble SKB, it was in outq->transmitted list
sctp_outq_sack
sctp_check_transmitted
SKB was moved to outq->sacked list
then throw away the sack queue
SKB was deleted from outq->sacked
(but it was held by datamsg at sctp_datamsg_to_asoc
So, sctp_wfree was not called here)
then migrate happened
sctp_for_each_tx_datachunk(
sctp_clear_owner_w);
sctp_assoc_migrate();
sctp_for_each_tx_datachunk(
sctp_set_owner_w);
SKB was not in the outq, and was not changed to newsk
finally
__sctp_outq_teardown
sctp_chunk_put (for another skb)
sctp_datamsg_put
__kfree_skb(msg->frag_list)
sctp_wfree (for SKB)
SKB->sk was still oldsk (skb->sk != asoc->base.sk).
Reported-and-tested-by: syzbot+cea71eec5d6de256d54d@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Acked-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when creating a new ipip interface with no local/remote configuration,
the lookup is done with TUNNEL_NO_KEY flag, making it impossible to
match the new interface (only possible match being fallback or metada
case interface); e.g: `ip link add tunl1 type ipip dev eth0`
To fix this case, adding a flag check before the key comparison so we
permit to match an interface with no local/remote config; it also avoids
breaking possible userland tools relying on TUNNEL_NO_KEY flag and
uninitialised key.
context being on my side, I'm creating an extra ipip interface attached
to the physical one, and moving it to a dedicated namespace.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it by adding a pair of rcu_read_lock/unlock() and use
cond_resched_rcu() to avoid the situation where walking of a large
number of items may prevent scheduling for a long time.
Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> Tested-by: Merlijn Wajer <merlijn@wizzup.org> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries") Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Changbin Du <changbin.du@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Keeping <john@metanate.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Lentine <mlentine@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core") Link: https://github.com/ClangBuiltLinux/linux/issues/924 Signed-off-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are at least 3 models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO
events on the external embedded-controller pin to avoid spurious wakeups
on the HP x2 10 CHT + AXP288 model too.
This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Reported-and-tested-by: Marc Lehmann <schmorp@schmorp.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-4-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to initialize a structure with "= {};" will not always clean out
all padding locations in a structure. So be explicit and call memset to
initialize everything for a number of bpf information structures that
are then copied from userspace, sometimes from smaller memory locations
than the size of the structure.
Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20200320162258.GA794295@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the bpf syscall, we are relying on the compiler to properly zero out
the bpf_attr union that we copy userspace data into. Unfortunately that
doesn't always work properly, padding and other oddities might not be
correctly zeroed, and in some tests odd things have been found when the
stack is pre-initialized to other values.
Fix this by explicitly memsetting the structure to 0 before using it.
Reported-by: Maciej Żenczykowski <maze@google.com> Reported-by: John Stultz <john.stultz@linaro.org> Reported-by: Alexander Potapenko <glider@google.com> Reported-by: Alistair Delva <adelva@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://android-review.googlesource.com/c/kernel/common/+/1235490 Link: https://lore.kernel.org/bpf/20200320094813.GA421650@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lex 2I385SW board has two Intel I211 ethernet controllers. Without
this patch, only the first port is usable. The second port fails to
start with the following message:
igb: probe of 0000:02:00.0 failed with error -2
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Tested-by: Georg Müller <georgmueller@gmx.net> Signed-off-by: Georg Müller <georgmueller@gmx.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
The original patch didn't copy the ieee80211_is_data() condition
because on most drivers the management frames don't go through
this path. However, they do on iwlwifi/mvm, so we do need to keep
the condition here.
Cc: stable@vger.kernel.org Fixes: ce2e1ca70307 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Woody Suwalski <terraluna977@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb17 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01") Fixes: 59f8b0bf3c12 ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting") Cc: stable <stable@vger.kernel.org> # 2.6.37 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d72c ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor") Fixes: c0b33bdc5b8d ("[media] gspca-stv06xx: support bandwidth changing") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading from a debugfs file at a nonzero position, without first reading
at position 0, leaks uninitialized memory to userspace.
It's a bit tricky to do this, since lseek() and pread() aren't allowed
on these files, and write() doesn't update the position on them. But
writing to them with splice() *does* update the position:
#define _GNU_SOURCE 1
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
int main()
{
int pipes[2], fd, n, i;
char buf[32];
pipe(pipes);
write(pipes[1], "0", 1);
fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR);
splice(pipes[0], NULL, fd, NULL, 1, 0);
n = read(fd, buf, sizeof(buf));
for (i = 0; i < n; i++)
printf("%02x", buf[i]);
printf("\n");
}
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber") Fixes: c53a846c48f2 ("[media] usbtv: add video controls") Cc: stable <stable@vger.kernel.org> # 3.11 Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes: 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") Cc: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a55165469 ("usb: musb: host: Handle highmem in PIO mode") Signed-off-by: Mans Rullgard <mans@mansr.com> Cc: stable@vger.kernel.org Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL") Cc: Anthony Mallet <anthony.mallet@laas.fr> Cc: stable <stable@vger.kernel.org> Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a frame is transmitted via the nl80211 TX rather than as a
normal frame, IEEE80211_TX_CTRL_PORT_CTRL_PROTO wasn't set and
this will lead to wrong decisions (rate control etc.) being made
about the frame; fix this.
Heiner writes:
commit 85a19b0e31e2 ("r8169: check that Realtek PHY driver
module is loaded") made it accidentally to 4.19 and causes an
issue with Android/x86. Could you please revert it?
Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vti6_rcv function performs some tests on the retrieved tunnel
including checking the IP protocol, the XFRM input policy, the
source and destination address.
In all but one places the skb is released in the error case. When
the input policy check fails the network packet is leaked.
Using the same goto-label discard in this case to fix this problem.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btf_enum_check_member() was currently sure to recognize the size of
"enum" type members in struct/union as the size of "int" even if
its size was packed.
This patch fixes BTF enum verification to use the correct size
of member in BPF programs.
projects / linux-stable / log