The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".
It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.
Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Meson SDIO controller uses the DAT0 lane for hardware busy
detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes
the following error observed with Linux 5.7 (pre-rc-1):
mmc1: Card stuck being busy! __mmc_poll_for_busy
blk_update_request: I/O error, dev mmcblk1, sector 17111080 op
0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0
Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.
This is done to avoid changing the value for different boards.
Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...") Cc: stable@vger.kernel.org # v4.16+ Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another. In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():
1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.
Rather than fixing the polling loop, use readx_poll_timeout() like
many people do. This has been time tested to handle the corner cases.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
One run of btrfs/063 triggered the following lockdep warning:
============================================
WARNING: possible recursive locking detected
5.6.0-rc7-custom+ #48 Not tainted
--------------------------------------------
kworker/u24:0/7 is trying to acquire lock: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
but task is already holding lock: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
other info that might help us debug this:
Possible unsafe locking scenario:
When we have an inode with a prealloc extent that starts at an offset
lower than the i_size and there is another prealloc extent that starts at
an offset beyond i_size, we can end up losing part of the first prealloc
extent (the part that starts at i_size) and have an implicit hole if we
fsync the file and then have a power failure.
Consider the following example with comments explaining how and why it
happens.
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our test file with 2 consecutive prealloc extents, each with a
# size of 128Kb, and covering the range from 0 to 256Kb, with a file
# size of 0.
$ xfs_io -f -c "falloc -k 0 128K" /mnt/foo
$ xfs_io -c "falloc -k 128K 128K" /mnt/foo
# Fsync the file to record both extents in the log tree.
$ xfs_io -c "fsync" /mnt/foo
# Now do a redudant extent allocation for the range from 0 to 64Kb.
# This will merely increase the file size from 0 to 64Kb. Instead we
# could also do a truncate to set the file size to 64Kb.
$ xfs_io -c "falloc 0 64K" /mnt/foo
# Fsync the file, so we update the inode item in the log tree with the
# new file size (64Kb). This also ends up setting the number of bytes
# for the first prealloc extent to 64Kb. This is done by the truncation
# at btrfs_log_prealloc_extents().
# This means that if a power failure happens after this, a write into
# the file range 64Kb to 128Kb will not use the prealloc extent and
# will result in allocation of a new extent.
$ xfs_io -c "fsync" /mnt/foo
# Now set the file size to 256K with a truncate and then fsync the file.
# Since no changes happened to the extents, the fsync only updates the
# i_size in the inode item at the log tree. This results in an implicit
# hole for the file range from 64Kb to 128Kb, something which fsck will
# complain when not using the NO_HOLES feature if we replay the log
# after a power failure.
$ xfs_io -c "truncate 256K" -c "fsync" /mnt/foo
So instead of always truncating the log to the inode's current i_size at
btrfs_log_prealloc_extents(), check first if there's a prealloc extent
that starts at an offset lower than the i_size and with a length that
crosses the i_size - if there is one, just make sure we truncate to a
size that corresponds to the end offset of that prealloc extent, so
that we don't lose the part of that extent that starts at i_size if a
power failure happens.
A test case for fstests follows soon.
Fixes: 31d11b83b96f ("Btrfs: fix duplicate extents after fsync of file with prealloc extents") CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the SELinux netlink_send hook to properly handle multiple netlink
messages in a single sk_buff; each message is parsed and subject to
SELinux access control. Prior to this patch, SELinux only inspected
the first message in the sk_buff.
Cc: stable@vger.kernel.org Reported-by: Dmitry Vyukov <dvyukov@google.com> Reviewed-by: Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some circumstances, i.e. when test is still running and about to
time out and user runs, for example,
grep -H . /sys/module/dmatest/parameters/*
the iterations parameter is not respected and test is going on and on until
user gives
echo 0 > /sys/module/dmatest/parameters/run
This is not what expected.
The history of this bug is interesting. I though that the commit 2d88ce76eb98 ("dmatest: add a 'wait' parameter")
is a culprit, but looking closer to the code I think it simple revealed the
broken logic from the day one, i.e. in the commit 0a2ff57d6fba ("dmaengine: dmatest: add a maximum number of test iterations")
which adds iterations parameter.
So, to the point, the conditional of checking the thread to be stopped being
first part of conjunction logic prevents to check iterations. Thus, we have to
always check both conditions to be able to stop after given iterations.
Since it wasn't visible before second commit appeared, I add a respective
Fixes tag.
Fixes: 2d88ce76eb98 ("dmatest: add a 'wait' parameter") Cc: Dan Williams <dan.j.williams@intel.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfs3_set_acl keeps track of the acl it allocated locally to determine if an acl
needs to be released at the end. This results in a memory leak when the
function allocates an acl as well as a default acl. Fix by releasing acls
that differ from the acl originally passed into nfs3_set_acl.
Fixes: b7fa0554cf1b ("[PATCH] NFS: Add support for NFSv3 ACLs") Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-10 points out a few instances of suspicious integer arithmetic
leading to value truncation:
sound/isa/opti9xx/opti92x-ad1848.c: In function 'snd_opti9xx_configure':
sound/isa/opti9xx/opti92x-ad1848.c:322:43: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_opti9xx_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
322 | (snd_opti9xx_read(chip, reg) & ~(mask)) | ((value) & (mask)))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/opti92x-ad1848.c:351:3: note: in expansion of macro 'snd_opti9xx_write_mask'
351 | snd_opti9xx_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
| ^~~~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c: In function 'snd_miro_configure':
sound/isa/opti9xx/miro.c:873:40: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_miro_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
873 | (snd_miro_read(chip, reg) & ~(mask)) | ((value) & (mask)))
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c:1010:3: note: in expansion of macro 'snd_miro_write_mask'
1010 | snd_miro_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
| ^~~~~~~~~~~~~~~~~~~
These are all harmless here as only the low 8 bit are passed down
anyway. Change the macros to inline functions to make the code
more readable and also avoid the warning.
Strictly speaking those functions also need locking to make the
read/write pair atomic, but it seems unlikely that anyone would
still run into that issue.
Currently, system fails to boot because the legacy interrupt remapping
mode does not enable 128-bit IRTE (GA), which is required for x2APIC
support.
Fix by using AMD_IOMMU_GUEST_IR_LEGACY_GA mode when booting with
kernel option amd_iommu_intr=legacy instead. The initialization
logic will check GASup and automatically fallback to using
AMD_IOMMU_GUEST_IR_LEGACY if GA mode is not supported.
SBC4 specifies that WRITE SAME requests with the UNMAP bit set to zero
"shall perform the specified write operation to each LBA specified by the
command". Commit 2237498f0b5c ("target/iblock: Convert WRITE_SAME to
blkdev_issue_zeroout") modified the iblock backend to call
blkdev_issue_zeroout() when handling WRITE SAME requests with UNMAP=0 and a
zero data segment.
The iblock blkdev_issue_zeroout() call incorrectly provides a flags
parameter of 0 (bool false), instead of BLKDEV_ZERO_NOUNMAP. The bool
false parameter reflects the blkdev_issue_zeroout() API prior to commit ee472d835c26 ("block: add a flags argument to (__)blkdev_issue_zeroout")
which was merged shortly before 2237498f0b5c.
Link: https://lore.kernel.org/r/20200419163109.11689-1-ddiss@suse.de Fixes: 2237498f0b5c ("target/iblock: Convert WRITE_SAME to blkdev_issue_zeroout") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.
Use follow_pfn() to get the PFN of a PFNMAP VMA instead of assuming that
vma->vm_pgoff holds the base PFN of the VMA. This fixes a bug where
attempting to do VFIO_IOMMU_MAP_DMA on an arbitrary PFNMAP'd region of
memory calculates garbage for the PFN.
Hilariously, this only got detected because the first "PFN" calculated
by vaddr_get_pfn() is PFN 0 (vma->vm_pgoff==0), and iommu_iova_to_phys()
uses PA==0 as an error, which triggers a WARN in vfio_unmap_unpin()
because the translation "failed". PFN 0 is now unconditionally reserved
on x86 in order to mitigate L1TF, which causes is_invalid_reserved_pfn()
to return true and in turns results in vaddr_get_pfn() returning success
for PFN 0. Eventually the bogus calculation runs into PFNs that aren't
reserved and leads to failure in vfio_pin_map_dma(). The subsequent
call to vfio_remove_dma() attempts to unmap PFN 0 and WARNs.
FDs can only be used on the ufile that created them, they cannot be mixed
to other ufiles. We are lacking a check to prevent it.
BUG: KASAN: null-ptr-deref in atomic64_sub_and_test include/asm-generic/atomic-instrumented.h:1547 [inline]
BUG: KASAN: null-ptr-deref in atomic_long_sub_and_test include/asm-generic/atomic-long.h:460 [inline]
BUG: KASAN: null-ptr-deref in fput_many+0x1a/0x140 fs/file_table.c:336
Write of size 8 at addr 0000000000000038 by task syz-executor179/284
Initialize ib_spec on the stack before using it, otherwise we will have
garbage values that will break creating default rules with invalid parsing
error.
Fixes: a37a1a428431 ("IB/mlx4: Add mechanism to support flow steering over IB links") Link: https://lore.kernel.org/r/20200413132235.930642-1-leon@kernel.org Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GRH fields such as sgid_index, hop limit, et. are set in the QP context
when QP is created/modified.
Currently, when query QP is performed, we fill the GRH fields only if the
GRH bit is set in the QP context, but this bit is not set for RoCE. Adjust
the check so we will set all relevant data for the RoCE too.
Since this data is returned to userspace, the below is an ABI regression.
Fixes: d8966fcd4c25 ("IB/core: Use rdma_ah_attr accessor functions") Link: https://lore.kernel.org/r/20200413132028.930109-1-leon@kernel.org Signed-off-by: Aharon Landau <aharonl@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qlt_free_session_done() tries to post async PRLO / LOGO, and waits for the
completion of these async commands. If UNLOADING is set, this is doomed to
timeout, because the async logout command will never complete.
The only way to avoid waiting pointlessly is to fail posting these commands
in the first place if the driver is in UNLOADING state. In general,
posting any command should be avoided when the driver is UNLOADING.
With this patch, "rmmod qla2xxx" completes without noticeable delay.
Link: https://lore.kernel.org/r/20200421204621.19228-3-mwilck@suse.com Fixes: 45235022da99 ("scsi: qla2xxx: Fix driver unload by shutting down chip") Acked-by: Arun Easi <aeasi@marvell.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of the UNLOADING flag is to avoid port login procedures to
continue when a controller is in the process of shutting down. It makes
sense to set this flag before starting session teardown.
Furthermore, use atomic test_and_set_bit() to avoid the shutdown being run
multiple times in parallel. In qla2x00_disable_board_on_pci_error(), the
test for UNLOADING is postponed until after the check for an already
disabled PCI board.
Link: https://lore.kernel.org/r/20200421204621.19228-2-mwilck@suse.com Fixes: 45235022da99 ("scsi: qla2xxx: Fix driver unload by shutting down chip") Reviewed-by: Arun Easi <aeasi@marvell.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding devices that don't have a scsi_dh on a BIO based multipath,
I was able to consistently hit the warning below and lock-up the system.
The problem is that __map_bio reads the flag before it potentially being
modified by choose_pgpath, and ends up using the older value.
The WARN_ON below is not trivially linked to the issue. It goes like
this: The activate_path delayed_work is not initialized for non-scsi_dh
devices, but we always set MPATHF_QUEUE_IO, asking for initialization.
That is fine, since MPATHF_QUEUE_IO would be cleared in choose_pgpath.
Nevertheless, only for BIO-based mpath, we cache the flag before calling
choose_pgpath, and use the older version when deciding if we should
initialize the path. Therefore, we end up trying to initialize the
paths, and calling the non-initialized activate_path work.
The dm-writecache reads metadata in the target constructor. However, when
we reload the target, there could be another active instance running on
the same device. This is the sequence of operations when doing a reload:
1. construct new target
2. suspend old target
3. resume new target
4. destroy old target
Metadata that were written by the old target between steps 1 and 2 would
not be visible by the new target.
Fix the data corruption by loading the metadata in the resume handler.
Also, validate block_size is at least as large as both the devices'
logical block size and only read 1 block from the metadata during
target constructor -- no need to read entirety of metadata now that it
is done during resume.
The error correction data is computed as if data and hash blocks
were concatenated. But hash block number starts from v->hash_start.
So, we have to calculate hash block number based on that.
Fixes: a739ff3f543af ("dm verity: add support for forward error correction") Cc: stable@vger.kernel.org Signed-off-by: Sunwook Eom <speed.eom@samsung.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the kernel threads are not frozen in software_resume(), so
between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
system_freezable_power_efficient_wq can still try to submit SCSI
commands and this can cause a panic since the low level SCSI driver
(e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
any SCSI commands: https://lkml.org/lkml/2020/4/10/47
At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
to resolve the issue from hv_storvsc, but with the help of
Bart Van Assche, I realized it's better to fix software_resume(),
since this looks like a generic issue, not only pertaining to SCSI.
Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The checks of the plugin buffer overflow in the previous fix by commit f2ecf903ef06 ("ALSA: pcm: oss: Avoid plugin buffer overflow")
are put in the wrong places mistakenly, which leads to the expected
(repeated) sound when the rate plugin is involved. Fix in the right
places.
Also, at those right places, the zero check is needed for the
termination node, so added there as well, and let's get it done,
finally.
This new Lenovo ThinkCenter has two front mics which can't be handled
by PA so far, so apply the fixup ALC283_FIXUP_HEADSET_MIC to change
the location for one of the mics.
btrfs_remove_block_group() invokes btrfs_lookup_block_group(), which
returns a local reference of the block group that contains the given
bytenr to "block_group" with increased refcount.
When btrfs_remove_block_group() returns, "block_group" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in several exception handling paths
of btrfs_remove_block_group(). When those error scenarios occur such as
btrfs_alloc_path() returns NULL, the function forgets to decrease its
refcnt increased by btrfs_lookup_block_group() and will cause a refcnt
leak.
Fix this issue by jumping to "out_put_group" label and calling
btrfs_put_block_group() when those error scenarios occur.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qxl_release should not be accesses after qxl_push_*_ring_release() calls:
userspace driver can process submitted command quickly, move qxl_release
into release_ring, generate interrupt and trigger garbage collector.
It can lead to crashes in qxl driver or trigger memory corruption
in some kmalloc-192 slab object
Gerd Hoffmann proposes to swap the qxl_release_fence_buffer_objects() +
qxl_push_{cursor,command}_ring_release() calls to close that race window.
The DispID DTD pixel clock is documented as:
"00 00 00 h → FF FF FF h | Pixel clock ÷ 10,000 0.01 → 167,772.16 Mega Pixels per Sec"
Which seems to imply that we to add one to the raw value.
Reality seems to agree as there are tiled displays in the wild
which currently show a 10kHz difference in the pixel clock
between the tiles (one tile gets its mode from the base EDID,
the other from the DispID block).
... to protect the modification of mp->m_count done by it. Most of
the places that modify that thing also have namespace_lock held,
but not all of them can do so, so we really need mount_lock here.
Kudos to Piotr Krysiuk <piotras@gmail.com>, who'd spotted a related
bug in pivot_root(2) (fixed unnoticed in 5.3); search for other
similar turds has caught out this one.
Cc: stable@kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While calculating overhead for internal journal, also check
that j_inum shouldn't be 0. Otherwise we get below error with
xfstests generic/050 with external journal (XXX_LOGDEV config) enabled.
It could be simply reproduced with loop device with an external journal
and marking blockdev as RO before mounting.
[ 3337.146838] EXT4-fs error (device pmem1p2): ext4_get_journal_inode:4634: comm mount: inode #0: comm mount: iget: illegal inode #
------------[ cut here ]------------
generic_make_request: Trying to write to read-only block-device pmem1p2 (partno 2)
WARNING: CPU: 107 PID: 115347 at block/blk-core.c:788 generic_make_request_checks+0x6b4/0x7d0
CPU: 107 PID: 115347 Comm: mount Tainted: G L --------- -t - 4.18.0-167.el8.ppc64le #1
NIP: c0000000006f6d44 LR: c0000000006f6d40 CTR: 0000000030041dd4
<...>
NIP [c0000000006f6d44] generic_make_request_checks+0x6b4/0x7d0
LR [c0000000006f6d40] generic_make_request_checks+0x6b0/0x7d0
<...>
Call Trace:
generic_make_request_checks+0x6b0/0x7d0 (unreliable)
generic_make_request+0x3c/0x420
submit_bio+0xd8/0x200
submit_bh_wbc+0x1e8/0x250
__sync_dirty_buffer+0xd0/0x210
ext4_commit_super+0x310/0x420 [ext4]
__ext4_error+0xa4/0x1e0 [ext4]
__ext4_iget+0x388/0xe10 [ext4]
ext4_get_journal_inode+0x40/0x150 [ext4]
ext4_calculate_overhead+0x5a8/0x610 [ext4]
ext4_fill_super+0x3188/0x3260 [ext4]
mount_bdev+0x778/0x8f0
ext4_mount+0x28/0x50 [ext4]
mount_fs+0x74/0x230
vfs_kern_mount.part.6+0x6c/0x250
do_mount+0x2fc/0x1280
sys_mount+0x158/0x180
system_call+0x5c/0x70
EXT4-fs (pmem1p2): no journal found
EXT4-fs (pmem1p2): can't get journal size
EXT4-fs (pmem1p2): mounted filesystem without journal. Opts: dax,norecovery
Fixes: 3c816ded78bb ("ext4: use journal inode to determine journal overhead") Reported-by: Harish Sriram <harish@linux.ibm.com> Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200316093038.25485-1-riteshh@linux.ibm.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qed_chain data structure was modified in
commit 1a4a69751f4d ("qed: Chain support for external PBL") to support
receiving an external pbl (due to iWARP FW requirements).
The pages pointed to by the pbl are allocated in qed_chain_alloc
and their virtual address are stored in an virtual addresses array to
enable accessing and freeing the data. The physical addresses however
weren't stored and were accessed directly from the external-pbl
during free.
Destroy-qp flow, leads to freeing the external pbl before the chain is
freed, when the chain is freed it tries accessing the already freed
external pbl, leading to a use-after-free. Therefore we need to store
the physical addresses in additional to the virtual addresses in a
new data structure.
Fixes: 1a4a69751f4d ("qed: Chain support for external PBL") Signed-off-by: Michal Kalderon <mkalderon@marvell.com> Signed-off-by: Yuval Bason <ybason@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current JIT clobbers the destination register for BPF_JSET BPF_X
and BPF_K by using "and" and "or" instructions. This is fine when the
destination register is a temporary loaded from a register stored on
the stack but not otherwise.
This patch fixes the problem (for both BPF_K and BPF_X) by always loading
the destination register into temporaries since BPF_JSET should not
modify the destination register.
This bug may not be currently triggerable as BPF_REG_AX is the only
register not stored on the stack and the verifier uses it in a limited
way.
Fixes: 03f5781be2c7b ("bpf, x86_32: add eBPF JIT compiler for ia32") Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Luke Nelson <luke.r.nels@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Wang YanQing <udknight@gmail.com> Link: https://lore.kernel.org/bpf/20200422173630.8351-2-luke.r.nels@gmail.com Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jc42 driver passes I2C client's name as hwmon device name. In case
of device tree probed devices this ends up being part of the compatible
string, "jc-42.4-temp". This name contains hyphens and the hwmon core
doesn't like this:
jc42 2-0018: hwmon: 'jc-42.4-temp' is not a valid name attribute, please fix
This changes the name to "jc42" which doesn't have any illegal
characters.
If the in-core buddy bitmap gets corrupted (or out of sync with the
block bitmap), issue a WARN_ON and try to recover. In most cases this
involves skipping trying to allocate out of a particular block group.
We can end up declaring the file system corrupted, which is fair,
since the file system probably should be checked before we proceed any
further.
Current wait times have proven to be too short to protect against inode
reuses that lead to metadata inconsistencies.
Now that we will retry the inode allocation if we can't find any
recently deleted inodes, it's a lot safer to increase the recently
deleted time from 5 seconds to a minute.
Run generic/388 with journal data mode sometimes may trigger the warning
in ext4_invalidatepage. Actually, we should use the matching invalidatepage
in ext4_writepage.
In assembly, many instances of __emit_inst(x) expand to a directive. In
a few places __emit_inst(x) is used as an assembler macro argument. For
example, in arch/arm64/kvm/hyp/entry.S
Both comma and space are separators, with an exception that content
inside a pair of parentheses/quotes is not split, so the clang
integrated assembler splits the arguments to:
GNU as preprocesses the input with do_scrub_chars(). Its arm64 backend
(along with many other non-x86 backends) sees:
alternative_insn nop,.inst(0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# .inst(...) is parsed as one argument
while its x86 backend sees:
alternative_insn nop,.inst (0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# The extra space before '(' makes the whole .inst (...) parsed as two arguments
The non-x86 backend's behavior is considered unintentional
(https://sourceware.org/bugzilla/show_bug.cgi?id=25750).
So drop the space separator inside `.inst (...)` to make the clang
integrated assembler work.
Before the pci_driver->probe() is called, the pci subsystem calls
runtime_forbid() and runtime_get_sync() on this pci dev, so only call
runtime_put_autosuspend() is not enough to enable the runtime_pm on
this device.
For controllers with vgaswitcheroo feature, the pci/quirks.c will call
runtime_allow() for this dev, then the controllers could enter
rt_idle/suspend/resume, but for non-vgaswitcheroo controllers like
Intel hda controllers, the runtime_pm is not enabled because the
runtime_allow() is not called.
Since it is no harm calling runtime_allow() twice, here let hda
driver call runtime_allow() for all controllers. Then the runtime_pm
is enabled on all controllers after the put_autosuspend() is called.
xenbus_map_ring_valloc() maps a ring page and returns the status of the
used grant (0 meaning success).
There are Xen hypervisors which might return the value 1 for the status
of a failed grant mapping due to a bug. Some callers of
xenbus_map_ring_valloc() test for errors by testing the returned status
to be less than zero, resulting in no error detected and crashing later
due to a not available ring page.
Set the return value of xenbus_map_ring_valloc() to GNTST_general_error
in case the grant status reported by Xen is greater than zero.
CONFIG_UBSAN_TRAP causes GCC to emit a UD2 whenever it encounters an
unreachable code path. This includes __builtin_unreachable(). Because
the BUG() macro uses __builtin_unreachable() after it emits its own UD2,
this results in a double UD2. In this case objtool rightfully detects
that the second UD2 is unreachable:
In case command ring buffer becomes inconsistent, tcmu sets device flag
TCMU_DEV_BIT_BROKEN. If the bit is set, tcmu rejects new commands from LIO
core with TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE, and no longer processes
completions from the ring. The reset_ring attribute can be used to
completely clean up the command ring, so after reset_ring the ring no
longer is inconsistent.
Therefore reset_ring also should reset bit TCMU_DEV_BIT_BROKEN to allow
normal processing.
Creation of the response to READ FULL STATUS fails for FC based
reservations. Reason is the too high loop limit (< 24) in
fc_get_pr_transport_id(). The string representation of FC WWPN is 23 chars
long only ("11:22:33:44:55:66:77:88"). So when i is 23, the loop body is
executed a last time for the ending '\0' of the string and thus hex2bin()
reports an error.
Link: https://lore.kernel.org/r/20200408132610.14623-3-bstroesser@ts.fujitsu.com Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when the HD-audio controller driver doesn't detect any
codecs, it tries to abort the probe. But this abort happens at the
delayed probe, i.e. the primary probe call already returned success,
hence the driver is never unbound until user does so explicitly.
As a result, it may leave the HD-audio device in the running state
without the runtime PM. More badly, if the device is a HD-audio bus
that is tied with a GPU, GPU cannot reach to the full power down and
consumes unnecessarily much power.
This patch changes the logic after no-codec situation; it continues
probing without the further codec initialization but keep the
controller driver running normally.
In the reflink extent remap function, it turns out that uirec (the block
mapping corresponding only to the part of the passed-in mapping that got
unmapped) was not fully initialized. Specifically, br_state was not
being copied from the passed-in struct to the uirec. This could lead to
unpredictable results such as the reflinked mapping being marked
unwritten in the destination file.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some SoCs, such as the i.MX6, it is necessary to set a bit
in the SoC level GPR register before suspending for wake on lan
to work.
The fec platform callback sleep_mode_enable was intended to allow this
but the platform implementation was NAK'd back in 2015 [1]
This means that, currently, wake on lan is broken on mainline for
the i.MX6 at least.
So implement the required bit setting in the fec driver by itself
by adding a new optional DT property indicating the GPR register
and adding the offset and bit information to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes an encoding bug in emit_stx for BPF_B when the source
register is BPF_REG_FP.
The current implementation for BPF_STX BPF_B in emit_stx saves one REX
byte when the operands can be encoded using Mod-R/M alone. The lower 8
bits of registers %rax, %rbx, %rcx, and %rdx can be accessed without using
a REX prefix via %al, %bl, %cl, and %dl, respectively. Other registers,
(e.g., %rsi, %rdi, %rbp, %rsp) require a REX prefix to use their 8-bit
equivalents (%sil, %dil, %bpl, %spl).
The current code checks if the source for BPF_STX BPF_B is BPF_REG_1
or BPF_REG_2 (which map to %rdi and %rsi), in which case it emits the
required REX prefix. However, it misses the case when the source is
BPF_REG_FP (mapped to %rbp).
The result is that BPF_STX BPF_B with BPF_REG_FP as the source operand
will read from register %ch instead of the correct %bpl. This patch fixes
the problem by fixing and refactoring the check on which registers need
the extra REX byte. Since no BPF registers map to %rsp, there is no need
to handle %spl.
Fixes: 622582786c9e0 ("net: filter: x86: internal BPF JIT") Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Luke Nelson <luke.r.nels@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200418232655.23870-1-luke.r.nels@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving PF_MEMALLOC set when exiting a kthread causes it to remain set
during do_exit(). That can confuse things. In particular, if BSD
process accounting is enabled, then do_exit() writes data to an
accounting file. If that file has FS_SYNC_FL set, then this write
occurs synchronously and can misbehave if PF_MEMALLOC is set.
For example, if the accounting file is located on an XFS filesystem,
then a WARN_ON_ONCE() in iomap_do_writepage() is triggered and the data
doesn't get written when it should. Or if the accounting file is
located on an ext4 filesystem without a journal, then a WARN_ON_ONCE()
in ext4_write_inode() is triggered and the inode doesn't get written.
Fix this in xfsaild() by using the helper functions to save and restore
PF_MEMALLOC.
This can be reproduced as follows in the kvm-xfstests test appliance
modified to add the 'acct' Debian package, and with kvm-xfstests's
recommended kconfig modified to add CONFIG_BSD_PROCESS_ACCT=y:
mkfs.xfs -f /dev/vdb
mount /vdb
touch /vdb/file
chattr +S /vdb/file
accton /vdb/file
mkfs.xfs -f /dev/vdc
mount /vdc
umount /vdc
This bug was originally reported by syzbot at
https://lore.kernel.org/r/0000000000000e7156059f751d7b@google.com.
Reported-by: syzbot+1f9dc49e8de2582d90c2@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: possible irq lock inversion dependency detected
5.6.0-rc7-syzkaller #0 Not tainted
--------------------------------------------------------
syz-executor.0/10317 just changed the state of lock: ffff888021d16568 (&(&info->lock)->rlock){+.+.}, at: spin_lock include/linux/spinlock.h:338 [inline] ffff888021d16568 (&(&info->lock)->rlock){+.+.}, at: shmem_mfill_atomic_pte+0x1012/0x21c0 mm/shmem.c:2407
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&(&xa->xa_lock)->rlock#5){..-.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
It is because CPU 0 held info->lock with IRQ enabled in userfaultfd_copy
path, then CPU 1 is splitting a THP which held xa_lock and info->lock in
IRQ disabled context at the same time. If softirq comes in to acquire
xa_lock, the deadlock would be triggered.
The fix is to acquire/release info->lock with *_irq version instead of
plain spin_{lock,unlock} to make it softirq safe.
Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Reported-by: syzbot+e27980339d305f2dbfd9@syzkaller.appspotmail.com Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: syzbot+e27980339d305f2dbfd9@syzkaller.appspotmail.com Acked-by: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Link: http://lkml.kernel.org/r/1587061357-122619-1-git-send-email-yang.shi@linux.alibaba.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current JIT uses the following sequence to zero-extend into the
upper 32 bits of the destination register for BPF_LDX BPF_{B,H,W},
when the destination register is not on the stack:
EMIT3(0xC7, add_1reg(0xC0, dst_hi), 0);
The problem is that C7 /0 encodes a MOV instruction that requires a 4-byte
immediate; the current code emits only 1 byte of the immediate. This
means that the first 3 bytes of the next instruction will be treated as
the rest of the immediate, breaking the stream of instructions.
This patch fixes the problem by instead emitting "xor dst_hi,dst_hi"
to clear the upper 32 bits. This fixes the problem and is more efficient
than using MOV to load a zero immediate.
This bug may not be currently triggerable as BPF_REG_AX is the only
register not stored on the stack and the verifier uses it in a limited
way, and the verifier implements a zero-extension optimization. But the
JIT should avoid emitting incorrect encodings regardless.
Fixes: 03f5781be2c7b ("bpf, x86_32: add eBPF JIT compiler for ia32") Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Luke Nelson <luke.r.nels@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com> Acked-by: Wang YanQing <udknight@gmail.com> Link: https://lore.kernel.org/bpf/20200422173630.8351-1-luke.r.nels@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.
Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.
When the kernel is built with CONFIG_DEBUG_PER_CPU_MAPS, the cpumap code
can trigger a spurious warning if CONFIG_CPUMASK_OFFSTACK is also set. This
happens because in this configuration, NR_CPUS can be larger than
nr_cpumask_bits, so the initial check in cpu_map_alloc() is not sufficient
to guard against hitting the warning in cpumask_check().
Fix this by explicitly checking the supplied key against the
nr_cpumask_bits variable before calling cpu_possible().
Fixes: 6710e1126934 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Xiumei Mu <xmu@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200416083120.453718-1-toke@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Google Apex Edge TPU devices have a class code of 0
(PCI_CLASS_NOT_DEFINED). This prevents the PCI core from assigning
resources for the Apex BARs because __dev_sort_resources() ignores
classless devices, host bridges, and IOAPICs.
On x86, firmware typically assigns those resources, so this was not a
problem. But on some architectures, firmware does *not* assign BARs, and
since the PCI core didn't do it either, the Apex device didn't work
correctly:
apex 0000:01:00.0: can't enable device: BAR 0 [mem 0x00000000-0x00003fff 64bit pref] not claimed
apex 0000:01:00.0: error enabling PCI device
f390d08d8b87 ("staging: gasket: apex: fixup undefined PCI class") added a
quirk to fix the class code, but it was in the apex driver, and if the
driver was built as a module, it was too late to help.
Move the quirk to the PCI core, where it will always run early enough that
the PCI core will assign resources if necessary.
Utilize the xpo_release_rqst transport method to ensure that each
rqstp's svc_rdma_recv_ctxt object is released even when the server
cannot return a Reply for that rqstp.
Without this fix, each RPC whose Reply cannot be sent leaks one
svc_rdma_recv_ctxt. This is a 2.5KB structure, a 4KB DMA-mapped
Receive buffer, and any pages that might be part of the Reply
message.
The leak is infrequent unless the network fabric is unreliable or
Kerberos is in use, as GSS sequence window overruns, which result
in connection loss, are more common on fast transports.
Fixes: 3a88092ee319 ("svcrdma: Preserve Receive buffer until svc_rdma_sendto") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's absolutely not safe to use resources pointed to by the @send_wr
argument of ib_post_send() _after_ that function returns. Those
resources are typically freed by the Send completion handler, which
can run before ib_post_send() returns.
Thus the trace points currently around ib_post_send() in the
server's RPC/RDMA transport are a hazard, even when they are
disabled. Rearrange them so that they touch the Work Request only
_before_ ib_post_send() is invoked.
The filesystem freeze sequence in XFS waits on any background
eofblocks or cowblocks scans to complete before the filesystem is
quiesced. At this point, the freezer has already stopped the
transaction subsystem, however, which means a truncate or cowblock
cancellation in progress is likely blocked in transaction
allocation. This results in a deadlock between freeze and the
associated scanner.
Fix this problem by holding superblock write protection across calls
into the block reapers. Since protection for background scans is
acquired from the workqueue task context, trylock to avoid a similar
deadlock between freeze and blocking on the write lock.
Fixes: d6b636ebb1c9f ("xfs: halt auto-reclamation activities while rebuilding rmap") Reported-by: Paul Furtado <paulfurtado91@gmail.com> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Chandan Rajendra <chandanrlinux@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Allison Collins <allison.henderson@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410b7 ("cxgb4: Add PHY firmware support for T420-BT cards") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57ca3 ("rxrpc: Add IPv6 support") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New struct nfsd4_blocked_lock allocated in find_or_allocate_block()
does not initialized nbl_list and nbl_lru.
If conflock allocation fails rollback can call list_del_init()
access uninitialized fields and corrupt memory.
v2: just initialize nbl_list and nbl_lru right after nbl allocation.
Fixes: 76d348fadff5 ("nfsd: have nfsd4_lock use blocking locks for v4.1+ lock") Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After suspend & resume, wm8960_hw_params may be called when
bias_level is not SND_SOC_BIAS_ON, then wm8960_configure_clocking
is not called. But if sample rate is changed at that time, then
the output clock rate will be not correct.
So judgement of bias_level is SND_SOC_BIAS_ON in wm8960_hw_params
is not necessary and it causes above issue.
Fixes: 3176bf2d7ccd ("ASoC: wm8960: update pll and clock setting function") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1587468525-27514-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probe fails after enabling the regulators regulator_put is called for
each supply without having them disabled before. This produces some
warnings like
WARNING: CPU: 0 PID: 90 at drivers/regulator/core.c:2044 _regulator_put.part.0+0x154/0x15c
[<c010f7a8>] (unwind_backtrace) from [<c010c544>] (show_stack+0x10/0x14)
[<c010c544>] (show_stack) from [<c012b640>] (__warn+0xd0/0xf4)
[<c012b640>] (__warn) from [<c012b9b4>] (warn_slowpath_fmt+0x64/0xc4)
[<c012b9b4>] (warn_slowpath_fmt) from [<c04c4064>] (_regulator_put.part.0+0x154/0x15c)
[<c04c4064>] (_regulator_put.part.0) from [<c04c4094>] (regulator_put+0x28/0x38)
[<c04c4094>] (regulator_put) from [<c04c40cc>] (regulator_bulk_free+0x28/0x38)
[<c04c40cc>] (regulator_bulk_free) from [<c0579b2c>] (release_nodes+0x1d0/0x22c)
[<c0579b2c>] (release_nodes) from [<c05756dc>] (really_probe+0x108/0x34c)
[<c05756dc>] (really_probe) from [<c0575aec>] (driver_probe_device+0xb8/0x16c)
[<c0575aec>] (driver_probe_device) from [<c0575d40>] (device_driver_attach+0x58/0x60)
[<c0575d40>] (device_driver_attach) from [<c0575da0>] (__driver_attach+0x58/0xcc)
[<c0575da0>] (__driver_attach) from [<c0573978>] (bus_for_each_dev+0x78/0xc0)
[<c0573978>] (bus_for_each_dev) from [<c0574b5c>] (bus_add_driver+0x188/0x1e0)
[<c0574b5c>] (bus_add_driver) from [<c05768b0>] (driver_register+0x74/0x108)
[<c05768b0>] (driver_register) from [<c061ab7c>] (i2c_register_driver+0x3c/0x88)
[<c061ab7c>] (i2c_register_driver) from [<c0102df8>] (do_one_initcall+0x58/0x250)
[<c0102df8>] (do_one_initcall) from [<c01a91bc>] (do_init_module+0x60/0x244)
[<c01a91bc>] (do_init_module) from [<c01ab5a4>] (load_module+0x2180/0x2540)
[<c01ab5a4>] (load_module) from [<c01abbd4>] (sys_finit_module+0xd0/0xe8)
[<c01abbd4>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Fixes: 3fd6e7d9a146 (ASoC: tas571x: New driver for TI TAS571x power amplifiers) Signed-off-by: Philipp Puschmann <p.puschmann@pironex.de> Link: https://lore.kernel.org/r/20200414112754.3365406-1-p.puschmann@pironex.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the MI2S DAIs do not have channels_min/max defined.
This means that snd_soc_dai_stream_valid() returns false,
i.e. the DAIs have neither valid playback nor capture stream.
It's quite surprising that this ever worked correctly,
but in 5.7-rc1 this is now failing badly: :)
Commit 0e9cf4c452ad ("ASoC: pcm: check if cpu-dai supports a given stream")
introduced a check for snd_soc_dai_stream_valid() before calling
hw_params(), which means that the q6i2s_hw_params() function
was never called, eventually resulting in:
qcom-q6afe aprsvc:q6afe:4:4: no line is assigned
... even though "qcom,sd-lines" is set in the device tree.
Commit 9b5db059366a ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported")
now even avoids creating PCM devices if the stream is not supported,
which means that it is failing even earlier with e.g.:
Primary MI2S: ASoC: no backend playback stream
Avoid all that trouble by adding channels_min/max for the MI2S DAIs.
Fixes: 24c4cbcfac09 ("ASoC: qdsp6: q6afe: Add q6afe dai driver") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20200415150050.616392-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b912841 ("iio:ad7793: Add support for the ad7796 and ad7797") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Restore the behavior of locking mmap_sem for reading in
binder_alloc_free_page(), as was first done in commit 3013bf62b67a
("binder: reduce mmap_sem write-side lock"). That change was
inadvertently reverted by commit 5cec2d2e5839 ("binder: fix race between
munmap() and direct reclaim").
In addition, change the name of the label for the error path to
accurately reflect that we're taking the lock for reading.
Backporting note: This fix is only needed when *both* of the commits
mentioned above are applied. That's an unlikely situation since they
both landed during the development of v5.1 but only one of them is
targeted for stable.
Fixes: 5cec2d2e5839 ("binder: fix race between munmap() and direct reclaim") Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Todd Kjos <tkjos@android.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QEMU has a funny new build error message when I use the upstream kernel
headers:
CC block/file-posix.o
In file included from /home/cborntra/REPOS/qemu/include/qemu/timer.h:4,
from /home/cborntra/REPOS/qemu/include/qemu/timed-average.h:29,
from /home/cborntra/REPOS/qemu/include/block/accounting.h:28,
from /home/cborntra/REPOS/qemu/include/block/block_int.h:27,
from /home/cborntra/REPOS/qemu/block/file-posix.c:30:
/usr/include/linux/swab.h: In function `__swab':
/home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:34: error: "sizeof" is not defined, evaluates to 0 [-Werror=undef]
20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE)
| ^~~~~~
/home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:41: error: missing binary operator before token "("
20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE)
| ^
cc1: all warnings being treated as errors
make: *** [/home/cborntra/REPOS/qemu/rules.mak:69: block/file-posix.o] Error 1
rm tests/qemu-iotests/socket_scm_helper.o
This was triggered by commit d5767057c9a ("uapi: rename ext2_swab() to
swab() and share globally in swab.h"). That patch is doing
#include <asm/bitsperlong.h>
but it uses BITS_PER_LONG.
The kernel file asm/bitsperlong.h provide only __BITS_PER_LONG.
Let us use the __ variant in swap.h
Link: http://lkml.kernel.org/r/20200213142147.17604-1-borntraeger@de.ibm.com Fixes: d5767057c9a ("uapi: rename ext2_swab() to swab() and share globally in swab.h") Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Yury Norov <yury.norov@gmail.com> Cc: Allison Randal <allison@lohutok.net> Cc: Joe Perches <joe@perches.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: William Breathitt Gray <vilhelm.gray@gmail.com> Cc: Torsten Hilbrich <torsten.hilbrich@secunet.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function do_write_buffer(), in the for loop, there is a case
chip_ready() returns 1 while chip_good() returns 0, so it never
break the loop.
To fix this, chip_good() is enough and it should timeout if it stay
bad for a while.
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value") Signed-off-by: Yi Huaijie <yihuaijie@huawei.com> Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Tokunori Ikegami <ikegami_to@yahoo.co.jp> Signed-off-by: Richard Weinberger <richard@nod.at> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Index of rvring is computed using pointer arithmetic. However, since
rvring->rvdev->vring is the base of the vring array, computation
of rvring idx should be reversed. It previously lead to writing at negative
indices in the resource table.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58bc ("s390: remove all code using the access register mode") Cc: stable@vger.kernel.org # 4.15+ Reported-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884 Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When performing rename operation with RENAME_WHITEOUT flag, we will
hold AGF lock to allocate or free extents in manipulating the dirents
firstly, and then doing the xfs_iunlink_remove() call last to hold
AGI lock to modify the tmpfile info, so we the lock order AGI->AGF.
The big problem here is that we have an ordering constraint on AGF
and AGI locking - inode allocation locks the AGI, then can allocate
a new extent for new inodes, locking the AGF after the AGI. Hence
the ordering that is imposed by other parts of the code is AGI before
AGF. So we get an ABBA deadlock between the AGI and AGF here.
In this patch we move the xfs_iunlink_remove() call to
before acquiring the AGF lock to preserve correct AGI/AGF locking
order.
[Minor massage required due to upstream change making xfs_bumplink() a
void function where as in the 4.19.y tree the return value is checked,
even though it is always zero. Only change was to the last code block
removed by the patch. Functionally equivalent to upstream.]
Signed-off-by: kaixuxia <kaixuxia@tencent.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Fixes: f9dc024a2da1f ("uas: pre_reset and suspend: Fix a few races") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Tested-by: Jonas Karlsson <jonas.karlsson@actia.se> Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log