Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
On s390, the layout of normal and large ptes (i.e. pmds/puds) differs.
Therefore, set_huge_pte_at() does a conversion from a normal pte to
the corresponding large pmd/pud. So, when converting an empty pte, this
should result in an empty pmd/pud, which would return true for
pmd/pud_none().
However, after conversion we also mark the pmd/pud as large, and
therefore present. For empty ptes, this will result in an empty pmd/pud
that is also marked as large, and pmd/pud_none() would not return true.
There is currently no issue with this behaviour, as set_huge_pte_at()
does not seem to be called for empty ptes. It would be valid though, so
let's fix this by not marking empty ptes as large in set_huge_pte_at().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add more arch page table helper
tests").
In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.
This change fixes the for-loop to only read/write six bytes.
Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Reported-by: Stan Johnson <userm57@yahoo.com> Tested-by: Stan Johnson <userm57@yahoo.com> Reported-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with Clang + -Wtautological-compare and
CONFIG_CPUMASK_OFFSTACK unset:
arch/x86/mm/mmio-mod.c:375:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL &&
^~~~~~~~~~~ ~~~~
arch/x86/mm/mmio-mod.c:405:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL || cpumask_weight(downed_cpus) == 0)
^~~~~~~~~~~ ~~~~
2 warnings generated.
Since entries are only added to the list and never deleted, use
list_for_each_entry_lockless() instead of list_for_each_entry_rcu for
traversing the list. Also, add a relevant comment in evm_secfs.c to
indicate this fact.
Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> (RCU viewpoint) Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Elide invalid configuration EZNPS + ARCv2, triggered by a
make allyesconfig build.
Granted the root cause is in source code (asm/barrier.h) where we check
for ARCv2 before PLAT_EZNPS, but it is better to avoid such combinations
at onset rather then baking subtle nuances into code.
As of today the ICCM and DCCM size checks are incorrectly using
mismatched units (KiB checked against bytes). The CONFIG_ARC_DCCM_SZ
and CONFIG_ARC_ICCM_SZ are in KiB, but the size calculated in
runtime and stored in cpu->dccm.sz and cpu->iccm.sz is in bytes.
A typical backtrace acquired from ftraced function currently looks like
the following (e.g. for "path_openat"):
arch_stack_walk+0x15c/0x2d8
stack_trace_save+0x50/0x68
stack_trace_call+0x15a/0x3b8
ftrace_graph_caller+0x0/0x1c
0x3e0007e3c98 <- ftraced function caller (should be do_filp_open+0x7c/0xe8)
do_open_execat+0x70/0x1b8
__do_execve_file.isra.0+0x7d8/0x860
__s390x_sys_execve+0x56/0x68
system_call+0xdc/0x2d8
Note random "0x3e0007e3c98" stack value as ftraced function caller. This
value causes either imprecise unwinder result or unwinding failure.
That "0x3e0007e3c98" comes from r14 of ftraced function stack frame, which
it haven't had a chance to initialize since the very first instruction
calls ftrace code ("ftrace_caller"). (ftraced function might never
save r14 as well). Nevertheless according to s390 ABI any function
is called with stack frame allocated for it and r14 contains return
address. "ftrace_caller" itself is called with "brasl %r0,ftrace_caller".
So, to fix this issue simply always save traced function caller onto
ftraced function stack frame.
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
export_imc_mode_and_cmd() function which creates the debugfs interface
for imc-mode and imc-command, is invoked when each nest pmu units is
registered.
When the first nest pmu unit is registered, export_imc_mode_and_cmd()
creates 'imc' directory under `/debug/powerpc/`. In the subsequent
invocations debugfs_create_dir() function returns, since the directory
already exists.
The recent commit <c33d442328f55> (debugfs: make error message a bit
more verbose), throws a warning if we try to invoke
`debugfs_create_dir()` with an already existing directory name.
Address this warning by making the debugfs directory registration in
the opal_imc_counters_probe() function, i.e invoke
export_imc_mode_and_cmd() function from the probe function.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com> Tested-by: Nageswara R Sastry <nasastry@in.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191127072035.4283-1-anju@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Both Ice Lake and Elkhart Lake (gen 11) support MST on all external
connections except DDI A. Tiger Lake (gen 12) supports on all external
connections.
Move the check to happen inside intel_dp_mst_encoder_init() and add
specific platform checks.
v2: Replace != with == checks for ports on gen < 11 (Ville)
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.
The fix is to pad skb->data to at least ETH_ZLEN bytes.
Cc: <stable@vger.kernel.org> Reported-by: Hu Jiahui <kirin.say@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In queuecommand path, if DMA map fails, it bails out with clock held. In
this case, release the clock to keep its usage paired.
[mkp: applied by hand]
Link: https://lore.kernel.org/r/0101016ed3d66395-1b7e7fce-b74d-42ca-a88a-4db78b795d3b-000000@us-west-2.amazonses.com Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[EB: resolved cherry-pick conflict caused by newer kernels not having
the clear_bit_unlock() line] Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_percpu() may return NULL, which means chan->buf may be set to NULL.
In that case, when we do *per_cpu_ptr(chan->buf, ...), we dereference an
invalid pointer:
BUG: Unable to handle kernel data access at 0x7dae0000
Faulting instruction address: 0xc0000000003f3fec
...
NIP relay_open+0x29c/0x600
LR relay_open+0x270/0x600
Call Trace:
relay_open+0x264/0x600 (unreliable)
__blk_trace_setup+0x254/0x600
blk_trace_setup+0x68/0xa0
sg_ioctl+0x7bc/0x2e80
do_vfs_ioctl+0x13c/0x1300
ksys_ioctl+0x94/0x130
sys_ioctl+0x48/0xb0
system_call+0x5c/0x68
Check if alloc_percpu returns NULL.
This was found by syzkaller both on x86 and powerpc, and the reproducer
it found on powerpc is capable of hitting the issue as an unprivileged
user.
Fixes: 017c59c042d0 ("relay: Use per CPU constructs for the relay channel buffer pointers") Reported-by: syzbot+1e925b4b836afe85a1c6@syzkaller-ppc64.appspotmail.com Reported-by: syzbot+587b2421926808309d21@syzkaller-ppc64.appspotmail.com Reported-by: syzbot+58320b7171734bf79d26@syzkaller.appspotmail.com Reported-by: syzbot+d6074fb08bdb2e010520@syzkaller.appspotmail.com Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Akash Goel <akash.goel@intel.com> Cc: Andrew Donnellan <ajd@linux.ibm.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Salvatore Bonaccorso <carnil@debian.org> Cc: <stable@vger.kernel.org> [4.10+] Link: http://lkml.kernel.org/r/20191219121256.26480-1-dja@axtens.net Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the AirVasT USB wireless devices 124a:4026
to the list of supported devices. It's using the ISL3886
usb firmware. Without this modification, the wiki adapter
is not recognized.
Cc: <stable@vger.kernel.org> Signed-off-by: Giuseppe Marco Randazzo <gmrandazzo@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [formatted, reworded] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200405220659.45621-1-chunkeey@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for non-working buttons on knock-off USB dongles for Sony
controllers. These USB dongles are used to connect older Sony DA/DS1/DS2
controllers via USB and are common on Amazon, AliExpress, etc. Without
the patch, the square, X, and circle buttons do not function. These
dongles used to work prior to kernel 4.10 but removing the global DS3
report fixup in commit e19a267b9987 ("HID: sony: DS3 comply to Linux gamepad
spec") exposed the problem.
Many people reported the problem on the Ubuntu forums and are working
around the problem by falling back to the 4.9 hid-sony driver.
The problem stems from these dongles incorrectly reporting their button
count as 13 instead of 16. This patch fixes up the report descriptor by
changing the button report count to 16 and removing 3 padding bits.
Cc: stable@vger.kernel.org Fixes: e19a267b9987 ("HID: sony: DS3 comply to Linux gamepad spec") Signed-off-by: Scott Shumate <scott.shumate@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original code in mm/mremap.c checks huge pmd by:
if (is_swap_pmd(*old_pmd) || pmd_trans_huge(*old_pmd)) {
However, a DAX mapped nvdimm is mapped as huge page (by default) but it
is not transparent huge page (_PAGE_PSE | PAGE_DEVMAP). This commit
changes the condition to include the case.
This addresses CVE-2020-10757.
Fixes: 5c7fb56e5e3f ("mm, dax: dax-pmd vs thp-pmd vs hugetlbfs-pmd") Cc: <stable@vger.kernel.org> Reported-by: Fan Yang <Fan_Yang@sjtu.edu.cn> Signed-off-by: Fan Yang <Fan_Yang@sjtu.edu.cn> Tested-by: Fan Yang <Fan_Yang@sjtu.edu.cn> Tested-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nd_label->dpa issue was observed when trying to enable the namespace created
with little-endian kernel on a big-endian kernel. That made me run
`sparse` on the rest of the code and other changes are the result of that.
This reverts commit 9a9e97b2f1f2 ("cgroup: Add memory barriers to plug
cgroup_rstat_updated() race window").
The commit was added in anticipation of memcg rstat conversion which needed
synchronous accounting for the event counters (e.g. oom kill count). However,
the conversion didn't get merged due to percpu memory overhead concern which
couldn't be addressed at the time.
Unfortunately, the patch's addition of smp_mb() to cgroup_rstat_updated()
meant that every scheduling event now had to go through an additional full
barrier and Mel Gorman noticed it as 1% regression in netperf UDP_STREAM test.
There's no need to have this barrier in tree now and even if we need
synchronous accounting in the future, the right thing to do is separating that
out to a separate function so that hot paths which don't care about
synchronous behavior don't have to pay the overhead of the full barrier. Let's
revert.
find_vmap_area() can return a NULL pointer and we're going to
dereference it without checking it first. Use the existing
find_vm_area() function which does exactly what we want and checks for
the NULL pointer.
>> include/linux/netfilter/nf_conntrack_pptp.h:13:20: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
extern const char *const pptp_msg_name(u_int16_t msg);
^~~~~~
Reported-by: kbuild test robot <lkp@intel.com> Fixes: 4c559f15efcc ("netfilter: nf_conntrack_pptp: prevent buffer overflows in debug code") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c8d ("bonding: add sysfs /slave dir for bond slave devices.") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function qlcnic_83xx_interrupt_test(), function
qlcnic_83xx_diag_alloc_res() is not handled by function
qlcnic_83xx_diag_free_res() after a call of the function
qlcnic_alloc_mbx_args() failed. Fix this issue by adding
a jump target "fail_mbx_args", and jump to this new target
when qlcnic_alloc_mbx_args() failed.
Fixes: b6b4316c8b2f ("qlcnic: Handle qlcnic_alloc_mbx_args() failure") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have logic to maintain network counters across resets by storing
the counters in bp->net_stats_prev before reset. But not all resets
will clear the counters. Certain resets that don't need to change
the number of rings do not clear the counters. The current logic
accumulates the counters before all resets, causing big jumps in
the counters after some resets, such as ethtool -G.
Fix it by only accumulating the counters during reset if the irq_re_init
parameter is set. The parameter signifies that all rings and interrupts
will be reset and that means that the counters will also be reset.
Reported-by: Vijayendra Suman <vijayendra.suman@oracle.com> Fixes: b8875ca356f1 ("bnxt_en: Save ring statistics before reset.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What it wants to get for x-proto in esp6_gso_encap() is the proto that
will be set in ESP nexthdr. So it should skip all ipv6 nexthdrs and
get the real transport protocol. Othersize, the wrong proto number
will be set into ESP nexthdr.
This patch is to skip all ipv6 nexthdrs by calling ipv6_skip_exthdr()
in esp6_gso_encap().
Fixes: 7862b4058b9f ("esp: Add gso handlers for esp4 and esp6") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IPSET_FLAG_SKIP_SUBCOUNTER_UPDATE is set, user requested to not
update counters in sub sets. Therefore IPSET_FLAG_SKIP_COUNTER_UPDATE
must be set, not unset.
Fixes: 6e01781d1c80e ("netfilter: ipset: set match: add support to match the counters") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Commit dd9ee3444014 ("vti4: Fix a ipip packet processing bug in
'IPCOMP' virtual tunnel"), it tries to receive IPIP packets in vti
by calling xfrm_input(). This case happens when a small packet or
frag sent by peer is too small to get compressed.
However, xfrm_input() will still get to the IPCOMP path where skb
sec_path is set, but never dropped while it should have been done
in vti_ipcomp4_protocol.cb_handler(vti_rcv_cb), as it's not an
ipcomp4 packet. This will cause that the packet can never pass
xfrm4_policy_check() in the upper protocol rcv functions.
So this patch is to call ip_tunnel_rcv() to process IPIP packets
instead.
Fixes: dd9ee3444014 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipip tunnel introduced in commit dd9ee3444014 ("vti4: Fix a ipip
packet processing bug in 'IPCOMP' virtual tunnel") largely duplicated
the existing vti_input and vti_recv functions. Refactored to
deduplicate the common code.
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 628e341f319f ("xfrm: make local
error reporting more robust"), but brought back by Commit 844d48746e4b
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: 844d48746e4b ("xfrm: choose protocol family by skb protocol") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 1 mark 0 mask 0x10 #[1]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x1 #[2]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x10 #[3]
The issue was introduced by Commit 7cb8a93968e3 ("xfrm: Allow inserting
policies with matching mark and different priorities"). After that, the
policies [1] and [2] would be able to be added with different priorities.
However, policy [3] will actually match both [1] and [2]. Policy [1]
was matched due to the 1st 'return true' in xfrm_policy_mark_match(),
and policy [2] was matched due to the 2nd 'return true' in there. It
caused WARN_ON() in xfrm_policy_insert_list().
This patch is to fix it by only (the same value and priority) as the
same policy in xfrm_policy_mark_match().
Thanks to Yuehaibing, we could make this fix better.
v1->v2:
- check policy->mark.v == pol->mark.v only without mask.
Fixes: 7cb8a93968e3 ("xfrm: Allow inserting policies with matching mark and different priorities") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the steps to reproduce the problem:
ip netns add foo
ip netns add bar
ip -n foo link add xfrmi0 type xfrm dev lo if_id 42
ip -n foo link set xfrmi0 netns bar
ip netns del foo
ip netns del bar
The problem is that x-netns xfrm interface are not removed when the link
netns is removed. This causes later this oops when thoses interfaces are
removed.
Let's add a handler to remove all interfaces related to a netns when this
netns is removed.
As on the tx path of vxlan over esp, skb->inner_network_header would be
set on vxlan_xmit() and xfrm4_tunnel_encap_add(), and the later one can
overwrite the former one. It causes skb_udp_tunnel_segment() to use a
wrong skb->inner_network_header, then the issue occurs.
This patch is to fix it by calling xfrm_output_gso() instead when the
inner_protocol is set, in which gso_segment of inner_protocol will be
done first.
While at it, also improve some code around.
Fixes: 7862b4058b9f ("esp: Add gso handlers for esp4 and esp6") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For beet mode, when it's ipv6 inner address with nexthdrs set,
the packet format might be:
----------------------------------------------------
| outer | | dest | | | ESP | ESP |
| IP hdr | ESP | opts.| TCP | Data | Trailer | ICV |
----------------------------------------------------
The nexthdr from ESP could be NEXTHDR_HOP(0), so it should
continue processing the packet when nexthdr returns 0 in
xfrm_input(). Otherwise, when ipv6 nexthdr is set, the
packet will be dropped.
I don't see any error cases that nexthdr may return 0. So
fix it by removing the check for nexthdr == 0.
The intermediate result of the old term (4UL * 1024 * 1024 * 1024) is
4 294 967 296 or 0x100000000 which is no problem on 64 bit systems.
The patch does not change the later overall result of 0x100000 for
MAX_DMA32_PFN (after it has been shifted by PAGE_SHIFT). The new
calculation yields the same result, but does not require 64 bit
arithmetic.
On 32 bit systems the old calculation suffers from an arithmetic
overflow in that intermediate term in braces: 4UL aka unsigned long int
is 4 byte wide and an arithmetic overflow happens (the 0x100000000 does
not fit in 4 bytes), the in braces result is truncated to zero, the
following right shift does not alter that, so MAX_DMA32_PFN evaluates to
0 on 32 bit systems.
That wrong value is a problem in a comparision against MAX_DMA32_PFN in
the init code for swiotlb in pci_swiotlb_detect_4gb() to decide if
swiotlb should be active. That comparison yields the opposite result,
when compiling on 32 bit systems.
This was not possible before
1b7e03ef7570 ("x86, NUMA: Enable emulation on 32bit too")
when that MAX_DMA32_PFN was first made visible to x86_32 (and which
landed in v3.0).
In practice this wasn't a problem, unless CONFIG_SWIOTLB is active on
x86-32.
However if one has set CONFIG_IOMMU_INTEL, since
c5a5dc4cbbf4 ("iommu/vt-d: Don't switch off swiotlb if bounce page is used")
there's a dependency on CONFIG_SWIOTLB, which was not necessarily
active before. That landed in v5.4, where we noticed it in the fli4l
Linux distribution. We have CONFIG_IOMMU_INTEL active on both 32 and 64
bit kernel configs there (I could not find out why, so let's just say
historical reasons).
The effect is at boot time 64 MiB (default size) were allocated for
bounce buffers now, which is a noticeable amount of memory on small
systems like pcengines ALIX 2D3 with 256 MiB memory, which are still
frequently used as home routers.
We noticed this effect when migrating from kernel v4.19 (LTS) to v5.4
(LTS) in fli4l and got that kernel messages for example:
Linux version 5.4.22 (buildroot@buildroot) (gcc version 7.3.0 (Buildroot 2018.02.8)) #1 SMP Mon Nov 26 23:40:00 CET 2018
…
Memory: 183484K/261756K available (4594K kernel code, 393K rwdata, 1660K rodata, 536K init, 456K bss , 78272K reserved, 0K cma-reserved, 0K highmem)
…
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0x0bb78000-0x0fb78000] (64MB)
The initial analysis and the suggested fix was done by user 'sourcejedi'
at stackoverflow and explicitly marked as GPLv2 for inclusion in the
Linux kernel:
https://unix.stackexchange.com/a/520525/50007
The new calculation, which does not suffer from that overflow, is the
same as for arch/mips now as suggested by Robin Murphy.
The fix was tested by fli4l users on round about two dozen different
systems, including both 32 and 64 bit archs, bare metal and virtualized
machines.
On a non-forwarding 802.11s link between two fairly busy
neighboring nodes (iperf with -P 16 at ~850MBit/s TCP;
1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4), so with
frequent PREQ retries, usually after around 30-40 seconds the
following crash would occur:
With some added debug output / delays we were able to push the crash from
the timer callback runner into the callback function and by that shedding
some light on which object holding the timer gets corrupted:
Fix use after free when user user space request uobject concurrently for
the same object, within the RCU grace period.
In that case, remove_handle_idr_uobject() is called twice and we will have
an extra put on the uobject which cause use after free. Fix it by leaving
the uobject write locked after it was removed from the idr.
Call to rdma_lookup_put_uobject with UVERBS_LOOKUP_DESTROY instead of
UVERBS_LOOKUP_WRITE will do the work.
Fixes: 7452a3c745a2 ("IB/uverbs: Allow RDMA_REMOVE_DESTROY to work concurrently with disassociate") Link: https://lore.kernel.org/r/20200527135534.482279-1-leon@kernel.org Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
The Debian kernel v5.6 triggers this kernel panic:
Kernel panic - not syncing: Bad Address (null pointer deref?)
Bad Address (null pointer deref?): Code=26 (Data memory access rights trap) at addr 0000000000000000
CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-2-parisc64 #1 Debian 5.6.14-1
IAOQ[0]: mem_init+0xb0/0x150
IAOQ[1]: mem_init+0xb4/0x150
RP(r2): start_kernel+0x6c8/0x1190
Backtrace:
[<0000000040101ab4>] start_kernel+0x6c8/0x1190
[<0000000040108574>] start_parisc+0x158/0x1b8
on a HP-PARISC rp3440 machine with this memory layout:
Memory Ranges:
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000004040000000 End 0x00000040ffdfffff Size 3070 MB
Fix the crash by avoiding virt_to_page() and similar functions in
mem_init() until the memory zones have been fully set up.
kobject_init_and_add() takes reference even when it fails.
Thus, when kobject_init_and_add() returns an error,
kobject_put() must be called to properly clean up the kobject.
KMSAN reported uninitialized data being written to disk when dumping
core. As a result, several kilobytes of kmalloc memory may be written
to the core file and then read by a non-privileged user.
Reported-by: sam <sunhaoyl@outlook.com> Signed-off-by: Alexander Potapenko <glider@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Kees Cook <keescook@chromium.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200419100848.63472-1-glider@google.com Link: https://github.com/google/kmsan/issues/76 Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace superfluous VM_BUG_ON() with comment about correct usage.
Technically reverts commit 1d148e218a0d ("mm: add VM_BUG_ON_PAGE() to
page_mapcount()"), but context lines have changed.
Function isolate_migratepages_block() runs some checks out of lru_lock
when choose pages for migration. After checking PageLRU() it checks
extra page references by comparing page_count() and page_mapcount().
Between these two checks page could be removed from lru, freed and taken
by slab.
As a result this race triggers VM_BUG_ON(PageSlab()) in page_mapcount().
Race window is tiny. For certain workload this happens around once a
year.
The code in isolate_migratepages_block() was added in commit 119d6d59dcc0 ("mm, compaction: avoid isolating pinned pages") before
adding VM_BUG_ON into page_mapcount().
This race has been predicted in 2015 by Vlastimil Babka (see link
below).
When connected mode is set, and we have connected and datagram traffic in
parallel, ipoib might crash with double free of datagram skb.
The current mechanism assumes that the order in the completion queue is
the same as the order of sent packets for all QPs. Order is kept only for
specific QP, in case of mixed UD and CM traffic we have few QPs (one UD and
few CM's) in parallel.
The problem:
----------------------------------------------------------
Transmit queue:
-----------------
UD skb pointer kept in queue itself, CM skb kept in spearate queue and
uses transmit queue as a placeholder to count the number of total
transmitted packets.
1. CM1 'wc' processing
- skb freed in cm separate ring.
- tx_tail of transmit queue increased although UD2 is not freed.
Now driver assumes UD2 index is already freed and it could be used for
new transmitted skb.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 .........127
------------------------------------------------------------
NL NL UD2 CM1 ud3 cm2 cm3 ud4 cm4 ud5 NL NL NL ...........
------------------------------------------------------------
^ ^ ^
(Bad)tail head
(Bad - Could be used for new SKB)
In this case (due to heavy load) UD2 skb pointer could be replaced by new
transmitted packet UD_NEW, as the driver assumes its free. At this point
we will have to process two 'wc' with same index but we have only one
pointer to free.
During second attempt to free the same skb we will have NULL pointer
exception.
2. UD2 'wc' processing
- skb freed according the index we got from 'wc', but it was already
overwritten by mistake. So actually the skb that was released is the
skb of the new transmitted packet and not the original one.
The fix:
-----------------------------------------------------------------------
The fix is to stop using the UD ring as a placeholder for CM packets, the
cyclic ring variables tx_head and tx_tail will manage the UD tx_ring, a
new cyclic variables global_tx_head and global_tx_tail are introduced for
managing and counting the overall outstanding sent packets, then the send
queue will be stopped and waken based on these variables only.
Note that no locking is needed since global_tx_head is updated in the xmit
flow and global_tx_tail is updated in the NAPI flow only. A previous
attempt tried to use one variable to count the outstanding sent packets,
but it did not work since xmit and NAPI flows can run at the same time and
the counter will be updated wrongly. Thus, we use the same simple cyclic
head and tail scheme that we have today for the UD tx_ring.
Fixes: 2c104ea68350 ("IB/ipoib: Get rid of the tx_outstanding variable in all modes") Link: https://lore.kernel.org/r/20200527134705.480068-1-leon@kernel.org Signed-off-by: Valentine Fatiev <valentinef@mellanox.com> Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Acked-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
OSD client should ignore cache/overlay flag if got redirect reply.
Otherwise, the client hangs when the cache tier is in forward mode.
[ idryomov: Redirects are effectively deprecated and no longer
used or tested. The original tiering modes based on redirects
are inherently flawed because redirects can race and reorder,
potentially resulting in data corruption. The new proxy and
readproxy tiering modes should be used instead of forward and
readforward. Still marking for stable as obviously correct,
though. ]
Gigabyte TRX40 Aorus Master is equipped with two USB-audio devices,
a Realtek ALC1220-VB codec (USB ID 0414:a001) and an ESS SABRE9218 DAC
(USB ID 0414:a000). The latter serves solely for the headphone output
on the front panel while the former serves for the rest I/Os (mostly
for the I/Os in the rear panel but also including the front mic).
Both chips do work more or less with the unmodified USB-audio driver,
but there are a few glitches. The ALC1220-VB returns an error for an
inquiry to some jacks, as already seen on other TRX40-based mobos.
However this machine has a slightly incompatible configuration, hence
the existing mapping cannot be used as is.
Meanwhile the ESS chip seems working without any quirk. But since
both audio devices don't provide any specific names, both cards appear
as "USB-Audio", and it's quite confusing for users.
This patch is an attempt to overcome those issues:
- The specific mapping table for ALC1220-VB is provided, reducing the
non-working nodes and renaming the badly chosen controls.
The connector map isn't needed here unlike other TRX40 quirks.
- For both USB IDs (0414:a000 and 0414:a001), provide specific card
name strings, so that user-space can identify more easily; and more
importantly, UCM profile can be applied to each.
An invariant of cap_bprm_set_creds is that every field in the new cred
structure that cap_bprm_set_creds might set, needs to be set every
time to ensure the fields does not get a stale value.
The field cap_ambient is not set every time cap_bprm_set_creds is
called, which means that if there is a suid or sgid script with an
interpreter that has neither the suid nor the sgid bits set the
interpreter should be able to accept ambient credentials.
Unfortuantely because cap_ambient is not reset to it's original value
the interpreter can not accept ambient credentials.
Given that the ambient capability set is expected to be controlled by
the caller, I don't think this is particularly serious. But it is
definitely worth fixing so the code works correctly.
I have tested to verify my reading of the code is correct and the
interpreter of a sgid can receive ambient capabilities with this
change and cannot receive ambient capabilities without this change.
Cc: stable@vger.kernel.org Cc: Andy Lutomirski <luto@kernel.org> Fixes: 58319057b784 ("capabilities: ambient capabilities") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Asus USB DAC is a USB type-C audio dongle for connecting to
the headset and headphone. The volume minimum value -23040 which
is 0xa600 in hexadecimal with the resolution value 1 indicates
this should be endianness issue caused by the firmware bug. Add
a volume quirk to fix the volume control problem.
Also fixes this warning:
Warning! Unlikely big volume range (=23040), cval->res is probably wrong.
[5] FU [Headset Capture Volume] ch = 1, val = -23040/0/1
Warning! Unlikely big volume range (=23040), cval->res is probably wrong.
[7] FU [Headset Playback Volume] ch = 1, val = -23040/0/1
We fixed the regression of the speaker volume for some Thinkpad models
(e.g. T570) by the commit 54947cd64c1b ("ALSA: hda/realtek - Fix
speaker output regression on Thinkpad T570"). Essentially it fixes
the DAC / pin pairing by a static table. It was confirmed and merged
to stable kernel later.
Now, interestingly, we got another regression report for the very same
model (T570) about the similar problem, and the commit above was the
culprit. That is, by some reason, there are devices that prefer the
DAC1, and another device DAC2!
Unfortunately those have the same ID and we have no idea what can
differentiate, in this patch, a new fixup model "tpt470-dock-fix" is
provided, so that users with such a machine can apply it manually.
When model=tpt470-dock-fix option is passed to snd-hda-intel module,
it avoids the fixed DAC pairing and the DAC1 is assigned to the
speaker like the earlier versions.
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates] Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag] Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kobject_init_and_add() returns an error in the function
qib_create_port_files(), the function kobject_put() is not called for the
corresponding kobject, which potentially leads to memory leak.
This patch fixes the issue by calling kobject_put() even if
kobject_init_and_add() fails. In addition, the ppd->diagc_kobj is released
along with other kobjects when the sysfs is unregistered.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Link: https://lore.kernel.org/r/20200512031328.189865.48627.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Suggested-by: Lin Yi <teroincn@gmail.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 7ecced0934e5 ("gpio: exar: add a check for the return value
of ida_simple_get fails") added a goto jump to the common error
handler for ida_simple_get() error, but this is wrong in two ways:
it doesn't set the proper return code and, more badly, it invokes
ida_simple_remove() with a negative index that shall lead to a kernel
panic via BUG_ON().
This patch addresses those two issues.
Fixes: 7ecced0934e5 ("gpio: exar: add a check for the return value of ida_simple_get fails") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tomas Paukrt reports that his SAM9X60 based system (ARM926, ARMv5TJ)
fails to fix up alignment faults, eventually resulting in a kernel
oops.
The problem occurs when using CONFIG_CPU_USE_DOMAINS with commit e6978e4bf181 ("ARM: save and reset the address limit when entering an
exception"). This is because the address limit is set back to
TASK_SIZE on exception entry, and, although it is restored on exception
exit, the domain register is not.
At this point, addr_limit is correctly restored to KERNEL_DS for
__probe_kernel_read() to continue execution, but dacr.kernel is not,
it has been reset by the set_fs(old_fs) to DOMAIN_CLIENT.
This would not have happened prior to the mentioned commit, because
addr_limit would remain KERNEL_DS, so get_fs() would have returned
KERNEL_DS, and so would correctly nest.
This commit fixes the problem by also saving the DACR on exception
entry if either CONFIG_CPU_SW_DOMAIN_PAN or CONFIG_CPU_USE_DOMAINS are
enabled, and resetting the DACR appropriately on exception entry to
match addr_limit and PAN settings.
Fixes: e6978e4bf181 ("ARM: save and reset the address limit when entering an exception") Reported-by: Tomas Paukrt <tomas.paukrt@advantech.cz> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Consolidate the user access assembly code to asm/uaccess-asm.h. This
moves the csdb, check_uaccess, uaccess_mask_range_ptr, uaccess_enable,
uaccess_disable, uaccess_save, uaccess_restore macros, and creates two
new ones for exception entry and exit - uaccess_entry and uaccess_exit.
This makes the uaccess_save and uaccess_restore macros private to
asm/uaccess-asm.h.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use unified assembler syntax (UAL) in headers. Divided syntax is
considered deprecated. This will also allow to build the kernel
using LLVM's integrated assembler.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a use-after-free noticed by running with KASAN enabled. If
rmi_irq_fn() is run twice in a row, then rmi_f11_attention() (among
others) will end up reading from drvdata->attn_data.data, which was
freed and left dangling in rmi_irq_fn().
Commit 55edde9fff1a ("Input: synaptics-rmi4 - prevent UAF reported by
KASAN") correctly identified and analyzed this bug. However the attempted
fix only NULLed out a local variable, missing the fact that
drvdata->attn_data is a struct, not a pointer.
NULL out the correct pointer in the driver data to prevent the attention
functions from copying from it.
On the Lenovo ThinkPad Twist S230u (3347-4HU) with BIOS version
"GDETC1WW (1.81 ) 06/27/2019", the keyboard, Synaptics TouchPad, and
TrackPoint either do not function or stop functioning a few minutes
after boot. This problem has been noted before, perhaps only occurring
with BIOS 1.57 and later.[1][2][3][4][5]
Odds of a BIOS fix appear to be low: 1.57 was released over 6 years ago
and although the [BIOS changelog] notes "Fixed an issue of UEFI
touchpad/trackpoint/keyboard/touchscreen" in 1.58, it appears to be
insufficient.
Setting i8042.reset=1 or adding 33474HU to the reset list avoids the
issue on my system from either warm or cold boot.
Sending [ 0x05, 0x20, 0x00, 0x0f, 0x06 ] packet for Xbox One S controllers
fixes an issue where controller is stuck in Bluetooth mode and not sending
any inputs.
input_flush_device() should only be called once the struct file is being
released and no open descriptors remain, but evdev_flush() was calling
it whenever a file descriptor was closed.
This caused uploaded force-feedback effects to be erased when a process
did a dup()/close() on the event FD, called system(), etc.
Call input_flush_device() from evdev_release() instead.
Based on available information this uses the singletouch irtouch
protocol. This is tested and confirmed to be fully functional on
the BonXeon TP hardware I have.
GCC 10 is very strict about symbol clash, and lwt_len_hist_user contains
a symbol which clashes with libbpf:
/usr/bin/ld: samples/bpf/lwt_len_hist_user.o:(.bss+0x0): multiple definition of `bpf_log_buf'; samples/bpf/bpf_load.o:(.bss+0x8c0): first defined here
collect2: error: ld returned 1 exit status
bpf_log_buf here seems to be a leftover, so removing it.
Drop static declaration to fix following build error if FRAME_POINTER disabled,
riscv64-linux-ld: arch/riscv/kernel/perf_callchain.o: in function `.L0':
perf_callchain.c:(.text+0x2b8): undefined reference to `walk_stackframe'
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I ran into a randconfig build failure with CONFIG_FIXED_PHY=m
and CONFIG_GIANFAR=y:
x86_64-linux-ld: drivers/net/ethernet/freescale/gianfar.o:(.rodata+0x418): undefined reference to `fixed_phy_change_carrier'
It seems the same thing can happen with dpaa and ucc_geth, so change
all three to do an explicit 'select FIXED_PHY'.
The fixed-phy driver actually has an alternative stub function that
theoretically allows building network drivers when fixed-phy is
disabled, but I don't see how that would help here, as the drivers
presumably would not work then.
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^ Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential race in fscache operation enqueuing for reading and
copying multiple pages from cachefiles to netfs. The problem can be seen
easily on a heavy loaded system (for example many processes reading files
continually on an NFS share covered by fscache triggered this problem within
a few minutes).
Before this patch, function gfs2_quota_lock checked if it was called
from a privileged user, and if so, it bypassed the quota check:
superuser can operate outside the quotas.
That's the wrong place for the check because the lock/unlock functions
are separate from the lock_check function, and you can do lock and
unlock without actually checking the quotas.
This patch moves the check to gfs2_quota_lock_check.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is another TRX40 based motherboard with ALC1220-VB USB-audio
that requires a static mapping table.
This motherboard also has a PCI device which advertises no codecs. The
PCI ID is 1022:1487 and PCI SSID is 1022:d102. As this is using the AMD
vendor ID, don't blacklist for now in case other boards have a working
audio device with the same ssid.
The driver currently leaves GPIO IRQs unmasked even when the GPIO IRQ
client has released the GPIO IRQ. This allows the HW to raise IRQs, and
SW to process them, after shutdown. Fix this by masking the IRQ when it's
shut down. This is usually taken care of by the irqchip core, but since
this driver has a custom irq_shutdown implementation, it must do this
explicitly itself.
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
projects / linux-stable / log