This fix allows ath9k_htc modules to connect to WLAN once again.
Fixes: 2bbcaaee1fcb ("ath9k: Fix general protection fault in ath9k_hif_usb_rx_cb") Link: https://bugzilla.kernel.org/show_bug.cgi?id=208251 Signed-off-by: Mark O'Donovan <shiftee@posteo.net> Reported-by: Roman Mamedov <rm@romanrm.net> Tested-by: Viktor Jägersküpper <viktor_jaegerskuepper@freenet.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200711043324.8079-1-shiftee@posteo.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ath9k_hif_usb_rx_cb interface number is assumed to be 0.
usb_ifnum_to_if(urb->dev, 0)
But it isn't always true.
The case reported by syzbot:
https://lore.kernel.org/linux-usb/000000000000666c9c05a1c05d12@google.com
usb 2-1: new high-speed USB device number 2 using dummy_hcd
usb 2-1: config 1 has an invalid interface number: 2 but max is 0
usb 2-1: config 1 has no interface number 0
usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice=
1.08
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
general protection fault, probably for non-canonical address
0xdffffc0000000015: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0
The problem is dm_suspended() returns true not only during suspend,
but also during resume. So this race condition could occur:
1. dm_integrity_resume calls queue_work(ic->recalc_wq, &ic->recalc_work)
2. integrity_recalc (&ic->recalc_work) preempts the current thread
3. integrity_recalc calls if (unlikely(dm_suspended(ic->ti))) goto unlock_ret;
4. integrity_recalc exits and no recalculating is done.
To fix this race condition, add a function dm_post_suspending that is
only true during the postsuspend phase and use it instead of
dm_suspended().
When building on allyesconfig kernel for a NO_DMA=y platform (e.g.
Sun-3), CONFIG_SND_SOC_QCOM_COMMON=y, but CONFIG_SND_SOC_QDSP6_AFE=n,
leading to a link failure:
sound/soc/qcom/common.o: In function `qcom_snd_parse_of':
common.c:(.text+0x2e2): undefined reference to `q6afe_is_rx_port'
While SND_SOC_QDSP6 depends on HAS_DMA, SND_SOC_MSM8996 and SND_SOC_SDM845
don't, so the following warning is seen:
Until recently, this warning was harmless (from a compile-testing
point-of-view), but the new user of q6afe_is_rx_port() turned this into
a hard failure.
As the QDSP6 driver itself builds fine if NO_DMA=y, and it depends on
QCOM_APR (which in turns depends on ARCH_QCOM || COMPILE_TEST), it is
safe to increase compile testing coverage. Hence fix the link failure
by dropping the HAS_DMA dependency of SND_SOC_QDSP6.
The Lenovo Miix 2 10 has a keyboard dock with extra speakers in the dock.
Rather then the ACL5672's GPIO1 pin being used as IRQ to the CPU, it is
actually used to enable the amplifier for these speakers
(the IRQ to the CPU comes directly from the jack-detect switch).
Add a quirk for having an ext speaker-amplifier enable pin on GPIO1
and replace the Lenovo Miix 2 10's dmi_system_id table entry's wrong
GPIO_DEV quirk (which needs to be renamed to GPIO1_IS_IRQ) with the
new RT5670_GPIO1_IS_EXT_SPK_EN quirk, so that we enable the external
speaker-amplifier as necessary.
Also update the ident field for the dmi_system_id table entry, the
Miix models are not Thinkpads.
On x86-32 the idt_table with 256 entries needs only 2048 bytes. It is
page-aligned, but the end of the .bss..page_aligned section is not
guaranteed to be page-aligned.
As a result, objects from other .bss sections may end up on the same 4k
page as the idt_table, and will accidentially get mapped read-only during
boot, causing unexpected page-faults when the kernel writes to them.
This could be worked around by making the objects in the page aligned
sections page sized, but that's wrong.
Explicit sections which store only page aligned objects have an implicit
guarantee that the object is alone in the page in which it is placed. That
works for all objects except the last one. That's inconsistent.
Enforcing page sized objects for these sections would wreckage memory
sanitizers, because the object becomes artificially larger than it should
be and out of bound access becomes legit.
Align the end of the .bss..page_aligned and .data..page_aligned section on
page-size so all objects places in these sections are guaranteed to have
their own page.
The code was stuck in this loop in d_alloc_parallel:
4037d414: 0e 00 10 dc ldd 0(r16),ret0 4037d418: c7 fc 5f ed bb,< ret0,1f,4037d414 <d_alloc_parallel+0x384> 4037d41c: 08 00 02 40 nop
This is the inner loop of bit_spin_lock which is called by hlist_bl_unlock in
d_alloc_parallel:
static inline void bit_spin_lock(int bitnum, unsigned long *addr)
{
/*
* Assuming the lock is uncontended, this never enters
* the body of the outer loop. If it is contended, then
* within the inner loop a non-atomic test is used to
* busywait with less bus contention for a good time to
* attempt to acquire the lock bit.
*/
preempt_disable();
#if defined(CONFIG_SMP) || defined(CONFIG_DEBUG_SPINLOCK)
while (unlikely(test_and_set_bit_lock(bitnum, addr))) {
preempt_enable();
do {
cpu_relax();
} while (test_bit(bitnum, addr));
preempt_disable();
}
#endif
__acquire(bitlock);
}
After consideration, I realized that we must be losing bit unlocks.
Then, I noticed that we missed defining atomic64_set_release().
Adding this define fixes the stalls in bit operations.
Avoid kernel crash when vddci_control is SMU7_VOLTAGE_CONTROL_NONE and
vddci_voltage_table is empty. It has been tested on Intel Hades Canyon
(i7-8809G).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=208489 Fixes: ac7822b0026f ("drm/amd/powerplay: add smumgr support for VEGAM (v2)") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Qiu Wenbo <qiuwenbo@phytium.com.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NULL dereference occurs when string that is not ended with space or
newline is written to some dpm sysfs interface (for example pp_dpm_sclk).
This happens because strsep replaces the tmp with NULL if the delimiter
is not present in string, which is then dereferenced by tmp[0].
Reproduction example:
sudo sh -c 'echo -n 1 > /sys/class/drm/card0/device/pp_dpm_sclk'
Signed-off-by: Paweł Gronowski <me@woland.xyz> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: cafaf14a5d8f ("io-mapping: Always create a struct to hold metadata about the io-mapping") Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200721171936.81563-1-michael.j.ruhl@intel.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the kmem_cache refcount is greater than one, we should not mark the
root kmem_cache as dying. If we mark the root kmem_cache dying
incorrectly, the non-root kmem_cache can never be destroyed. It
resulted in memory leak when memcg was destroyed. We can use the
following steps to reproduce.
1) Use kmem_cache_create() to create a new kmem_cache named A.
2) Coincidentally, the kmem_cache A is an alias for kmem_cache B,
so the refcount of B is just increased.
3) Use kmem_cache_destroy() to destroy the kmem_cache A, just
decrease the B's refcount but mark the B as dying.
4) Create a new memory cgroup and alloc memory from the kmem_cache
B. It leads to create a non-root kmem_cache for allocating memory.
5) When destroy the memory cgroup created in the step 4), the
non-root kmem_cache can never be destroyed.
If we repeat steps 4) and 5), this will cause a lot of memory leak. So
only when refcount reach zero, we mark the root kmem_cache as dying.
Fixes: 92ee383f6daa ("mm: fix race between kmem_cache destroy, create and deactivate") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200716165103.83462-1-songmuchun@bytedance.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the memcg_params.dying flag and the corresponding workqueue used
for the asynchronous deactivation of kmem_caches is synchronized using the
slab_mutex.
It makes impossible to check this flag from the irq context, which will be
required in order to implement asynchronous release of kmem_caches.
So let's switch over to the irq-save flavor of the spinlock-based
synchronization.
Link: http://lkml.kernel.org/r/20190611231813.3148843-8-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Waiman Long <longman@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Andrei Vagin <avagin@gmail.com> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was hard to keep a test running, moving tasks between memcgs with
move_charge_at_immigrate, while swapping: mem_cgroup_id_get_many()'s
refcount is discovered to be 0 (supposedly impossible), so it is then
forced to REFCOUNT_SATURATED, and after thousands of warnings in quick
succession, the test is at last put out of misery by being OOM killed.
This is because of the way moved_swap accounting was saved up until the
task move gets completed in __mem_cgroup_clear_mc(), deferred from when
mem_cgroup_move_swap_account() actually exchanged old and new ids.
Concurrent activity can free up swap quicker than the task is scanned,
bringing id refcount down 0 (which should only be possible when
offlining).
Just skip that optimization: do that part of the accounting immediately.
Fixes: 615d66c37c75 ("mm: memcontrol: fix memcg id ref counter on swap charge move") Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alex Shi <alex.shi@linux.alibaba.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2007071431050.4726@eggly.anvils Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CROSS_COMPILE is set (e.g. aarch64-linux-gnu-), if
$(CROSS_COMPILE)elfedit is found at /usr/bin/aarch64-linux-gnu-elfedit,
GCC_TOOLCHAIN_DIR will be set to /usr/bin/. --prefix= will be set to
/usr/bin/ and Clang as of 11 will search for both
$(prefix)aarch64-linux-gnu-$needle and $(prefix)$needle.
GCC searchs for $(prefix)aarch64-linux-gnu/$version/$needle,
$(prefix)aarch64-linux-gnu/$needle and $(prefix)$needle. In practice,
$(prefix)aarch64-linux-gnu/$needle rarely contains executables.
To better model how GCC's -B/--prefix takes in effect in practice, newer
Clang (since
https://github.com/llvm/llvm-project/commit/3452a0d8c17f7166f479706b293caf6ac76ffd90)
only searches for $(prefix)$needle. Currently it will find /usr/bin/as
instead of /usr/bin/aarch64-linux-gnu-as.
Set --prefix= to $(GCC_TOOLCHAIN_DIR)$(notdir $(CROSS_COMPILE))
(/usr/bin/aarch64-linux-gnu-) so that newer Clang can find the
appropriate cross compiling GNU as (when -no-integrated-as is in
effect).
syzbot is reporting general protection fault in do_con_write() [1] caused
by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0
caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by
fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for
gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate()
from con_install() from tty_init_dev() from tty_open() on such console
causes vc->vc_pos == 0x10000000e due to
((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1).
I don't think that a console with 0 column or 0 row makes sense. And it
seems that vc_do_resize() does not intend to allow resizing a console to
0 column or 0 row due to
Theoretically, cols and rows can be any range as long as
0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g.
cols == 1048576 && rows == 2 is possible) because of
in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate().
Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in
visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return
an error, and con_write() will not be called on a console with 0 column
or 0 row.
We need to make sure that integer overflow in visual_init() won't happen.
Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying
1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate()
will be practically fine.
This patch does not touch con_init(), for returning -EINVAL there
does not help when we are not returning -ENOMEM.
syzbot is reporting general protection fault in bitfill_aligned() [1]
caused by integer underflow in bit_clear_margins(). The cause of this
problem is when and how do_vc_resize() updates vc->vc_{cols,rows}.
If vc_do_resize() fails (e.g. kzalloc() fails) when var.xres or var.yres
is going to shrink, vc->vc_{cols,rows} will not be updated. This allows
bit_clear_margins() to see info->var.xres < (vc->vc_cols * cw) or
info->var.yres < (vc->vc_rows * ch). Unexpectedly large rw or bh will
try to overrun the __iomem region and causes general protection fault.
Also, vc_resize(vc, 0, 0) does not set vc->vc_{cols,rows} = 0 due to
Of course, callers of vc_resize() are not handling vc_do_resize() failure
is bad. But we can't avoid vc_resize(vc, 0, 0) which returns 0. Therefore,
as a band-aid workaround, this patch checks integer underflow in
"struct fbcon_ops"->clear_margins call, assuming that
vc->vc_cols * vc->vc_font.width and vc->vc_rows * vc->vc_font.heigh do not
cause integer overflow.
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
SERIAL_PORT_DFNS is not defined on each arch, if it's not defined,
serial8250_set_defaults() won't be called in serial8250_isa_init_ports(),
so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref.
Fix this problem by calling serial8250_set_defaults() after init uart port.
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this.
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this, adjusting the checks
for invalid channels so that enabled channel bits that would have been
lost by shifting are also checked for validity. Only channels 0 to 15
are valid.
Fixes: a8c66b684efaf ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions") Cc: <stable@vger.kernel.org> #4.0+: ef75e14a6c93: staging: comedi: verify array index is correct before using it Cc: <stable@vger.kernel.org> #4.0+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20200717145257.112660-5-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`ni6527_intr_insn_config()` processes `INSN_CONFIG` comedi instructions
for the "interrupt" subdevice. When `data[0]` is
`INSN_CONFIG_DIGITAL_TRIG` it is configuring the digital trigger. When
`data[2]` is `COMEDI_DIGITAL_TRIG_ENABLE_EDGES` it is configuring rising
and falling edge detection for the digital trigger, using a base channel
number (or shift amount) in `data[3]`, a rising edge bitmask in
`data[4]` and falling edge bitmask in `data[5]`.
If the base channel number (shift amount) is greater than or equal to
the number of channels (24) of the digital input subdevice, there are no
changes to the rising and falling edges, so the mask of channels to be
changed can be set to 0, otherwise the mask of channels to be changed,
and the rising and falling edge bitmasks are shifted by the base channel
number before calling `ni6527_set_edge_detection()` to change the
appropriate registers. Unfortunately, the code is comparing the base
channel (shift amount) to the interrupt subdevice's number of channels
(1) instead of the digital input subdevice's number of channels (24).
Fix it by comparing to 32 because all shift amounts for an `unsigned
int` must be less than that and everything from bit 24 upwards is
ignored by `ni6527_set_edge_detection()` anyway.
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this.
Fixes: 33cdce6293dcc ("staging: comedi: addi_apci_1032: conform to new INSN_CONFIG_DIGITAL_TRIG") Cc: <stable@vger.kernel.org> #3.8+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20200717145257.112660-3-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon additional testing with older servers, it was found that
the original commit introduced a regression when using the old SMB1
dialect and rsyncing over an existing file.
The patch will need to be respun to address this, likely including
a larger refactoring of the SMB1 and SMB3 rename code paths to make
it less confusing and also to address some additional rename error
cases that SMB3 may be able to workaround.
Signed-off-by: Steve French <stfrench@microsoft.com> Reported-by: Patrick Fernie <patrick.fernie@gmail.com> CC: Stable <stable@vger.kernel.org> Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Acked-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASM2142/ASM3142 (same PCI IDs) does not support full 64-bit DMA
addresses, which can cause silent memory corruption or IOMMU errors on
platforms that use the upper bits. Add the XHCI_NO_64BIT_SUPPORT quirk
to fix this issue.
The wMaxPacketSize field of endpoint descriptor may be zero
as default value in alternate interface, and they are not
actually selected when start stream, so skip them when try to
allocate bandwidth.
syzbot is reporting that mmput() from shrinker function has a risk of
deadlock [1], for delayed_uprobe_add() from update_ref_ctr() calls
kzalloc(GFP_KERNEL) with delayed_uprobe_lock held, and
uprobe_clear_state() from __mmput() also holds delayed_uprobe_lock.
Commit a1b2289cef92ef0e ("android: binder: drop lru lock in isolate
callback") replaced mmput() with mmput_async() in order to avoid sleeping
with spinlock held. But this patch replaces mmput() with mmput_async() in
order not to start __mmput() from shrinker context.
While digging through the recent mmiowb preemption issue it came up that
we aren't actually preventing IO from crossing a scheduling boundary.
While it's a bit ugly to overload smp_mb__after_spinlock() with this
behavior, it's what PowerPC is doing so there's some precedent.
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
gr_ep_init() does not assign the allocated request anywhere if allocation
of memory for the buffer fails. This is a memory leak fixed by the given
patch.
Found by Linux Driver Verification project (linuxtesting.org).
DMA transaction time to completion is a function of PCI bandwidth,
transaction size and a queue depth. So hard coded value for timeouts
might be wrong for some scenarios.
aspeed_create_fan() reads a pwm_port value using of_property_read_u32().
If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be
a buffer overflow in
aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes
the potential buffer overflow.
Found by Linux Driver Verification project (linuxtesting.org).
This function is used by dev_get_regmap() to retrieve a regmap for the
specified device. If the device has more than one regmap, the name parameter
can be used to specify one.
The code here uses a pointer comparison to check for equal strings. This
however will probably always fail, as the regmap->name is allocated via
kstrdup_const() from the regmap's config->name.
This event code represents the state of a removable cover of a device.
Value 0 means that the cover is open or removed, value 1 means that the
cover is closed.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
The Maxxter KB-BT-001 Bluetooth keyboard, which looks somewhat like the
Apple Wireless Keyboard, is using the vendor and product IDs (05AC:0239)
of the Apple Wireless Keyboard (2009 ANSI version) <sigh>.
But its F1 - F10 keys are marked as sending F1 - F10, not the special
functions hid-apple.c maps them too; and since its descriptors do not
contain the HID_UP_CUSTOM | 0x0003 usage apple-hid looks for for the
Fn-key, apple_setup_input() never gets called, so F1 - F6 are mapped
to key-codes which have not been set in the keybit array causing them
to not send any events at all.
The lack of a usage code matching the Fn key in the clone is actually
useful as this allows solving this problem in a generic way.
This commits adds a fn_found flag and it adds a input_configured
callback which checks if this flag is set once all usages have been
mapped. If it is not set, then assume this is a clone and clear the
quirks bitmap so that the hid-apple code does not add any special
handling to this keyboard.
This fixes F1 - F6 not sending anything at all and F7 - F12 sending
the wrong codes on the Maxxter KB-BT-001 Bluetooth keyboard and on
similar clones.
Cc: Joao Moreno <mail@joaomoreno.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using uhid and KASAN this driver crashed because it was getting
several connection events where it only expected one. Then the
device was added several times to the static device list and it got
corrupted.
This patch checks if the device is already in the list before adding
it.
Commit ed66f991bb19 ("module: Refactor section attr into bin attribute")
removed the 'name' field from 'struct module_sect_attr' triggering the
following error when invoking lx-symbols:
(gdb) lx-symbols
loading vmlinux
scanning for modules in linux/build
loading @0xffffffffc014f000: linux/build/drivers/net/tun.ko
Python Exception <class 'gdb.error'> There is no member named name.:
Error occurred in Python: There is no member named name.
This patch fixes the issue taking the module name from the 'struct
attribute'.
Fixes: ed66f991bb19 ("module: Refactor section attr into bin attribute") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Kieran Bingham <kbingham@kernel.org> Link: http://lkml.kernel.org/r/20200722102239.313231-1-sgarzare@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the basepath is removed only from the beginning of the string.
When the symbol is inlined and there's multiple line outputs of
addr2line, only the first line would have basepath removed.
Change to remove the basepath prefix from all lines.
Fixes: 31013836a71e ("scripts/decode_stacktrace: match basepath using shell prefix operator, not regex") Co-developed-by: Shik Chen <shik@chromium.org> Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Signed-off-by: Shik Chen <shik@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Cc: Sasha Levin <sashal@kernel.org> Cc: Nicolas Boichat <drinkcat@chromium.org> Cc: Jiri Slaby <jslaby@suse.cz> Link: http://lkml.kernel.org/r/20200720082709.252805-1-pihsun@chromium.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit 7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Very similar to commit 544f287b8495
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f5f ("bonding: set carrier off for devices created through netlink") Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com Cc: Beniamino Galvani <bgalvani@redhat.com> Cc: Taehee Yoo <ap420073@gmail.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When regmap_update_bits failed in ave_init(), calls of the functions
reset_control_assert() and clk_disable_unprepare() were missed.
Add goto out_reset_assert to do this.
Fixes: 57878f2f4697 ("net: ethernet: ave: add support for phy-mode setting of system controller") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sync_thread_backup only checks sk_receive_queue is empty or not,
there is a situation which cannot sync the connection entries when
sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf,
the sync packets are dropped in __udp_enqueue_schedule_skb, this is
because the packets in reader_queue is not read, so the rmem is
not reclaimed.
Here I add the check of whether the reader_queue of the udp sock is
empty or not to solve this problem.
Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception") Reported-by: zhouxudong <zhouxudong8@huawei.com> Signed-off-by: guodeqing <geffrey.guo@huawei.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the verbosity of the "don't support RoCE & iWARP simultaneously"
warning to debug level to stop flooding on driver/hardware initialization:
[ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth0]
[ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth1]
[ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth2]
[ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth3]
[ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
[ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0
[MBI 15.10.6] [eth4]
[ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't
support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only
Fixes: e0a8f9de16fc ("qed: Add iWARP enablement support") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When mlxsw_core_trap_register fails in mlxsw_emad_init,
destroy_workqueue() shouled be called to destroy mlxsw_core->emad_wq.
Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock") Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If register_netdevice() is failed, net_device should not be used
because variables are uninitialized or freed.
So, the routine should be stopped immediately.
But, bond_create() doesn't check return value of register_netdevice()
immediately. That will result in a panic because of using uninitialized
or freed memory.
Fixes: e826eafa65c6 ("bonding: Call netif_carrier_off after register_netdevice") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev)
should be called to free the ndev created earlier. Otherwise, a memleak
will occur.
Fixes: 7d2911c43815 ("net: smc91x: Fix gpios for device tree based booting") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A driver which supports hardware time stamping shall update the
struct with the actual, possibly more permissive configuration.
Do update the struct passed when we upscale the requested time
stamping mode.
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Sergey Organov <sorganov@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.
Fixes: a9a51bd727d1 ("ax88172a: fix information leak on short answers") Signed-off-by: George Kennedy <george.kennedy@oracle.com> Reported-by: syzbot+4cd84f527bf4a10fc9c1@syzkaller.appspotmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago. The pause setting was missed when
making that change. Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().
Fixes: e2dc9b6e38fa ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When locking pages for delalloc, we check if it's dirty and mapping still
matches. If it does not match, we need to return -EAGAIN and release all
pages. Only the current page was put though, iterate over all the
remaining pages too.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Robbie Ko <robbieko@synology.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to cause a btrfs mount to fail by racing it with a slow
umount. The crux of the sequence is generic_shutdown_super not yet
calling sop->put_super before btrfs_mount_root calls btrfs_open_devices.
If that occurs, btrfs_open_devices will decide the opened counter is
non-zero, increment it, and skip resetting fs_devices->total_rw_bytes to
0. From here, mount will call sget which will result in grab_super
trying to take the super block umount semaphore. That semaphore will be
held by the slow umount, so mount will block. Before up-ing the
semaphore, umount will delete the super block, resulting in mount's sget
reliably allocating a new one, which causes the mount path to dutifully
fill it out, and increment total_rw_bytes a second time, which causes
the mount to fail, as we see double the expected bytes.
To fix this, we clear total_rw_bytes from within btrfs_read_chunk_tree
before the calls to read_one_dev, while holding the sb umount semaphore
and the uuid mutex.
To reproduce, it is sufficient to dirty a decent number of inodes, then
quickly umount and mount.
for i in $(seq 0 500)
do
dd if=/dev/zero of="/mnt/foo/$i" bs=1M count=1
done
umount /mnt/foo&
mount /mnt/foo
does the trick for me.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Boris Burkov <boris@bur.io> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At btrfs_find_all_roots_safe() we allocate a ulist and set the **roots
argument to point to it. However if later we fail due to an error returned
by find_parent_nodes(), we free that ulist but leave a dangling pointer in
the **roots argument. Upon receiving the error, a caller of this function
can attempt to free the same ulist again, resulting in an invalid memory
access.
One such scenario is during qgroup accounting:
btrfs_qgroup_account_extents()
--> calls btrfs_find_all_roots() passes &new_roots (a stack allocated
pointer) to btrfs_find_all_roots()
--> btrfs_find_all_roots() just calls btrfs_find_all_roots_safe()
passing &new_roots to it
--> allocates ulist and assigns its address to **roots (which
points to new_roots from btrfs_qgroup_account_extents())
--> find_parent_nodes() returns an error, so we free the ulist
and leave **roots pointing to it after returning
--> btrfs_qgroup_account_extents() sees btrfs_find_all_roots() returned
an error and jumps to the label 'cleanup', which just tries to
free again the same ulist
The RT5670_PWR_ANLG1 register has 3 bits to select the LDO voltage,
so the correct mask is 0x7 not 0x3.
Because of this wrong mask we were programming the ldo bits
to a setting of binary 001 (0x05 & 0x03) instead of binary 101
when moving to SND_SOC_BIAS_PREPARE.
According to the datasheet 001 is a reserved value, so no idea
what it did, since the driver was working fine before I guess we
got lucky and it does something which is ok.
Fixes: 5e8351de740d ("ASoC: add RT5670 CODEC driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200628155231.71089-3-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_info_get_line() has a sanity check of NULL buffer -- both buffer
itself being NULL and buffer->buffer being NULL. Basically both
checks are valid and necessary, but the problem is that it's with
snd_BUG_ON() macro that triggers WARN_ON(). The latter condition
(NULL buffer->buffer) can be met arbitrarily by user since the buffer
is allocated at the first write, so it means that user can trigger
WARN_ON() at will.
This patch addresses it by simply moving buffer->buffer NULL check out
of snd_BUG_ON() so that spurious WARNING is no longer triggered.
If a tracee is uprobed and it hits int3 inserted by debugger, handle_swbp()
does send_sig(SIGTRAP, current, 0) which means si_code == SI_USER. This used
to work when this code was written, but then GDB started to validate si_code
and now it simply can't use breakpoints if the tracee has an active uprobe:
# gcc -g test.c -o test
# perf probe -x ./test -a unused_func
# perf record -e probe_test:unused_func gdb ./test -ex run
GNU gdb (GDB) 10.0.50.20200714-git
...
Program received signal SIGTRAP, Trace/breakpoint trap.
0x00007ffff7ddf909 in dl_main () from /lib64/ld-linux-x86-64.so.2
(gdb)
The tracee hits the internal breakpoint inserted by GDB to monitor shared
library events but GDB misinterprets this SIGTRAP and reports a signal.
Change handle_swbp() to use force_sig(SIGTRAP), this matches do_int3_user()
and fixes the problem.
This is the minimal fix for -stable, arch/x86/kernel/uprobes.c is equally
wrong; it should use send_sigtrap(TRAP_TRACE) instead of send_sig(SIGTRAP),
but this doesn't confuse GDB and needs another x86-specific patch.
Yang Yingliang [Tue, 14 Jul 2020 14:56:39 +0000 (14:56 +0000)]
IB/umem: fix reference count leak in ib_umem_odp_get()
Add missing mmput() on error path to avoid ref-count leak.
This problem is introduced by 79bb5b7ee177 ("RDMA/umem: Fix missing mmap_sem in get umem ODP call")
and resolved by f27a0d50a4bc ("RDMA/umem: Use umem->owning_mm inside ODP").
So, it's only needed in stable-4.14 and stable-4.19.
Fixes: 79bb5b7ee177 ("RDMA/umem: Fix missing mmap_sem in get umem ODP call") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe9329f ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com> Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[acj: backport v4.19 -stable
- adjust context
- skipped the hunk modifying non-existent function tipc_mcast_send_sync
- additional comment ] Signed-off-by: Aviraj CJ <acj@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DSPI interrupt can be shared between two controllers at least on the
LX2160A. In that case, the driver for one controller might misbehave and
consume the other's interrupt. Fix this by actually checking if any of
the bits in the status register have been asserted.
Fixes: 13aed2392741 ("spi: spi-fsl-dspi: use IRQF_SHARED mode to request IRQ") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20190822212450.21420-2-olteanv@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reverting commit d03727b248d0 "NFSv4 fix CLOSE not waiting for
direct IO compeletion". This patch made it so that fput() by calling
inode_dio_done() in nfs_file_release() would wait uninterruptably
for any outstanding directIO to the file (but that wait on IO should
be killable).
The problem the patch was also trying to address was REMOVE returning
ERR_ACCESS because the file is still opened, is supposed to be resolved
by server returning ERR_FILE_OPEN and not ERR_ACCESS.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504eb ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode") Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The CPU mask (@tmp) should be released on failing to allocate
@cpu_groups or any of its elements. Otherwise, it leads to memory
leakage because the CPU mask variable is dynamically allocated
when CONFIG_CPUMASK_OFFSTACK is enabled.
So handle similar to skge.c's gm_phy_read, initialize v.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes,
then this driver will prepend a length field of 2 bytes,
then the underlying Ethernet device will prepend its own header.
So, the header length required should be:
-1 + 3 + 2 + "the header length needed by the underlying device".
This patch fixes kernel panic when this driver is used with AF_PACKET
SOCK_DGRAM sockets.
Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang static analysis flags several null function pointer problems.
drivers/scsi/scsi_transport_spi.c:374:1: warning: Called function pointer is null (null dereference) [core.CallAndMessage]
spi_transport_max_attr(offset, "%d\n");
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reviewing the store_spi_store_max macro
if (i->f->set_##field)
return -EINVAL;
should be
if (!i->f->set_##field)
return -EINVAL;
Link: https://lore.kernel.org/r/20200627133242.21618-1-trix@redhat.com Reviewed-by: James Bottomley <jejb@linux.ibm.com> Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without this patch, eapol frames cannot be received in mesh
mode, when 802.1X should be used. Initially only a MGTK is
defined, which is found and set as rx->key, when there are
no other keys set. ieee80211_drop_unencrypted would then
drop these eapol frames, as they are data frames without
encryption and there exists some rx->key.
Fix this by differentiating between mesh eapol frames and
other data frames with existing rx->key. Allow mesh mesh
eapol frames only if they are for our vif address.
With this patch in-place, ieee80211_rx_h_mesh_fwding continues
after the ieee80211_drop_unencrypted check and notices, that
these eapol frames have to be delivered locally, as they should.
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count. Call pm_runtime_put if
pm_runtime_get_sync fails.
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH,
which would be loaded to watchdog counter once writing WDG_LOAD_LOW.
Fixes: ac1775012058 ("spi: sprd: Add the support of restarting the system") Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently target_copy() is used only for sending linger pings, so
this doesn't come up, but generally omitting recovery_deletes can
result in unneeded resends (force_resend in calc_target()).
Fixes: ae78dd8139ce ("libceph: make RECOVERY_DELETES feature create a new interval") Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
printk_deferred(), similarly to printk_safe/printk_nmi, does not
immediately attempt to print a new message on the consoles, avoiding
calls into non-reentrant kernel paths, e.g. scheduler or timekeeping,
which potentially can deadlock the system.
Those printk() flavors, instead, rely on per-CPU flush irq_work to print
messages from safer contexts. For same reasons (recursive scheduler or
timekeeping calls) printk() uses per-CPU irq_work in order to wake up
user space syslog/kmsg readers.
However, only printk_safe/printk_nmi do make sure that per-CPU areas
have been initialised and that it's safe to modify per-CPU irq_work.
This means that, for instance, should printk_deferred() be invoked "too
early", that is before per-CPU areas are initialised, printk_deferred()
will perform illegal per-CPU access.
Lech Perczak [0] reports that after commit 1b710b1b10ef ("char/random:
silence a lockdep splat with printk()") user-space syslog/kmsg readers
are not able to read new kernel messages.
The reason is printk_deferred() being called too early (as was pointed
out by Petr and John).
Fix printk_deferred() and do not queue per-CPU irq_work before per-CPU
areas are initialized.
Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.
X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.
Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:
- Store it in the irq descriptors affinity mask
- Update the effective affinity to reflect that so user space has
a consistent view
- Don't call into the irq chip driver
This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.
Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.
For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.
Remove the X86 workaround as it is not longer required.
task_h_load() can return 0 in some situations like running stress-ng
mmapfork, which forks thousands of threads, in a sched group on a 224 cores
system. The load balance doesn't handle this correctly because
env->imbalance never decreases and it will stop pulling tasks only after
reaching loop_max, which can be equal to the number of running tasks of
the cfs. Make sure that imbalance will be decreased by at least 1.
misfit task is the other feature that doesn't handle correctly such
situation although it's probably more difficult to face the problem
because of the smaller number of CPUs and running tasks on heterogenous
system.
We can't simply ensure that task_h_load() returns at least one because it
would imply to handle underflow in other places.
While integrating rseq into glibc and replacing glibc's sched_getcpu
implementation with rseq, glibc's tests discovered an issue with
incorrect __rseq_abi.cpu_id field value right after the first time
a newly created process issues sched_setaffinity.
For the records, it triggers after building glibc and running tests, and
then issuing:
for x in {1..2000} ; do posix/tst-affinity-static & done
and shows up as:
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 2, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
error: Unexpected CPU 138, expected 0
This is caused by the scheduler invoking __set_task_cpu() directly from
sched_fork() and wake_up_new_task(), thus bypassing rseq_migrate() which
is done by set_task_cpu().
Add the missing rseq_migrate() to both functions. The only other direct
use of __set_task_cpu() is done by init_idle(), which does not involve a
user-space task.
Based on my testing with the glibc test-case, just adding rseq_migrate()
to wake_up_new_task() is sufficient to fix the observed issue. Also add
it to sched_fork() to keep things consistent.
The reason why this never triggered so far with the rseq/basic_test
selftest is unclear.
The current use of sched_getcpu(3) does not typically require it to be
always accurate. However, use of the __rseq_abi.cpu_id field within rseq
critical sections requires it to be accurate. If it is not accurate, it
can cause corruption in the per-cpu data targeted by rseq critical
sections in user-space.
Although we zero the upper bits of x0 on entry to the kernel from an
AArch32 task, we do not clear them on the exception return path and can
therefore expose 64-bit sign extended syscall return values to userspace
via interfaces such as the 'perf_regs' ABI, which deal exclusively with
64-bit registers.
Explicitly clear the upper 32 bits of x0 on return from a compat system
call.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the arm64 single-step state machine can be fast-forwarded in
cases where we wish to generate a SIGTRAP without actually executing an
instruction, this has two major limitations outside of simply skipping
an instruction due to emulation.
1. Stepping out of a ptrace signal stop into a signal handler where
SIGTRAP is blocked. Fast-forwarding the stepping state machine in
this case will result in a forced SIGTRAP, with the handler reset to
SIG_DFL.
2. The hardware implicitly fast-forwards the state machine when executing
an SVC instruction for issuing a system call. This can interact badly
with subsequent ptrace stops signalled during the execution of the
system call (e.g. SYSCALL_EXIT or seccomp traps), as they may corrupt
the stepping state by updating the PSTATE for the tracee.
Resolve both of these issues by injecting a pseudo-singlestep exception
on entry to a signal handler and also on return to userspace following a
system call.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Tested-by: Luis Machado <luis.machado@linaro.org> Reported-by: Keno Fischer <keno@juliacomputing.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luis reports that, when reverse debugging with GDB, single-step does not
function as expected on arm64:
| I've noticed, under very specific conditions, that a PTRACE_SINGLESTEP
| request by GDB won't execute the underlying instruction. As a consequence,
| the PC doesn't move, but we return a SIGTRAP just like we would for a
| regular successful PTRACE_SINGLESTEP request.
The underlying problem is that when the CPU register state is restored
as part of a reverse step, the SPSR.SS bit is cleared and so the hardware
single-step state can transition to the "active-pending" state, causing
an unexpected step exception to be taken immediately if a step operation
is attempted.
In hindsight, we probably shouldn't have exposed SPSR.SS in the pstate
accessible by the GPR regset, but it's a bit late for that now. Instead,
simply prevent userspace from configuring the bit to a value which is
inconsistent with the TIF_SINGLESTEP state for the task being traced.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Link: https://lore.kernel.org/r/1eed6d69-d53d-9657-1fc9-c089be07f98c@linaro.org Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
/* KHz mW */
{ 1008000, 36, 0 },
{ 1200000, 49, 0 },
{ 1296000, 59, 0 },
{ 1416000, 72, 0 },
{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.
Fixes: 349d39dc5739 ("thermal: cpu_cooling: merge frequency and power tables") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uninterruptible context is not needed in the driver and causes lockdep
warning because of mutex taken in of_alias_get_id(). Convert the lock to
mutex to avoid the issue.
projects / linux-stable / log