A spanking new machine I just got has all but one USB ports wired as 3.0.
Booting defconfig resulted in no keyboard or mouse, which was pretty
uncool. Let's enable that -- USB3 is ubiquitous rather than an oddity.
As 'y' not 'm' -- recovering from initrd problems needs a keyboard.
Also add it to the 32-bit defconfig.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-usb@vger.kernel.org Link: http://lkml.kernel.org/r/20181009062803.4332-1-kilobyte@angband.pl Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 problems with it:
1. "<" vs expected "<<"
2. the shift number is an IOMMU page number mask, not an address
mask as the IOMMU page shift is missing.
This did not hit us before f1565c24b596 ("powerpc: use the generic
dma_ops_bypass mode") because we had additional code to handle bypass
mask so this chunk (almost?) never executed.However there were
reports that aacraid does not work with "iommu=nobypass".
After f1565c24b596, aacraid (and probably others which call
dma_get_required_mask() before setting the mask) was unable to enable
64bit DMA and fall back to using IOMMU which was known not to work,
one of the problems is double free of an IOMMU page.
This fixes DMA for aacraid, both with and without "iommu=nobypass" in
the kernel command line. Verified with "stress-ng -d 4".
Fixes: 6a5c7be5e484 ("powerpc: Override dma_get_required_mask by platform hook and ops") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200908015106.79661-1-aik@ozlabs.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
The x86-64 psABI [0] specifies special relocation types
(R_X86_64_[REX_]GOTPCRELX) for indirection through the Global Offset
Table, semantically equivalent to R_X86_64_GOTPCREL, which the linker
can take advantage of for optimization (relaxation) at link time. This
is supported by LLD and binutils versions 2.26 onwards.
The compressed kernel is position-independent code, however, when using
LLD or binutils versions before 2.27, it must be linked without the -pie
option. In this case, the linker may optimize certain instructions into
a non-position-independent form, by converting foo@GOTPCREL(%rip) to $foo.
This potential issue has been present with LLD and binutils-2.26 for a
long time, but it has never manifested itself before now:
- LLD and binutils-2.26 only relax
movq foo@GOTPCREL(%rip), %reg
to
leaq foo(%rip), %reg
which is still position-independent, rather than
mov $foo, %reg
which is permitted by the psABI when -pie is not enabled.
- GCC happens to only generate GOTPCREL relocations on mov instructions.
- CLang does generate GOTPCREL relocations on non-mov instructions, but
when building the compressed kernel, it uses its integrated assembler
(due to the redefinition of KBUILD_CFLAGS dropping -no-integrated-as),
which has so far defaulted to not generating the GOTPCRELX
relocations.
Nick Desaulniers reports [1,2]:
"A recent change [3] to a default value of configuration variable
(ENABLE_X86_RELAX_RELOCATIONS OFF -> ON) in LLVM now causes Clang's
integrated assembler to emit R_X86_64_GOTPCRELX/R_X86_64_REX_GOTPCRELX
relocations. LLD will relax instructions with these relocations based
on whether the image is being linked as position independent or not.
When not, then LLD will relax these instructions to use absolute
addressing mode (R_RELAX_GOT_PC_NOPIC). This causes kernels built with
Clang and linked with LLD to fail to boot."
Patch series [4] is a solution to allow the compressed kernel to be
linked with -pie unconditionally, but even if merged is unlikely to be
backported. As a simple solution that can be applied to stable as well,
prevent the assembler from generating the relaxed relocation types using
the -mrelax-relocations=no option. For ease of backporting, do this
unconditionally.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
Variable populated, which is a member of struct pcpu_chunk, is used as a
unit of size of unsigned long.
However, size of populated is miscounted. So, I fix this minor part.
Fixes: 8ab16c43ea79 ("percpu: change the number of pages marked in the first_chunk pop bitmap") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Sunghyun Jin <mcsmonk@gmail.com> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On suspend the original host configuration gets restored. The
resume routine has to undo this, otherwise the SMBus master
may be left in disabled state or in i2c mode.
[JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.]
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
if of_find_device_by_node() succeed, mtk_drm_kms_init() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
On A20R machines the interrupt pending bits in cause register need to be
updated by requesting the chipset to do it. This needs to be done to
find the interrupt cause and after interrupt service. In
commit 0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions") the
function to do after service update got lost, which caused spurious
interrupts.
Fixes: 0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions") Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting OOB read at fbcon_resize() [1], for
commit 39b3cffb8cf31117 ("fbcon: prevent user font height or width change
from causing potential out-of-bounds access") is by error using
registered_fb[con2fb_map[vc->vc_num]]->fbcon_par->p->userfont (which was
set to non-zero) instead of fb_display[vc->vc_num].userfont (which remains
zero for that display).
We could remove tricky userfont flag [2], for we can determine it by
comparing address of the font data and addresses of built-in font data.
But since that commit is failing to fix the original OOB read [3], this
patch keeps the change minimal in case we decide to revert altogether.
Indirect leak of 360 byte(s) in 9 object(s) allocated from:
#0 0x7fecc305180e in calloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10780e)
#1 0x560578f6dce5 in perf_pmu__new_format util/pmu.c:1333
#2 0x560578f752fc in perf_pmu_parse util/pmu.y:59
#3 0x560578f6a8b7 in perf_pmu__format_parse util/pmu.c:73
#4 0x560578e07045 in test__pmu tests/pmu.c:155
#5 0x560578de109b in run_test tests/builtin-test.c:410
#6 0x560578de109b in test_and_print tests/builtin-test.c:440
#7 0x560578de401a in __cmd_test tests/builtin-test.c:661
#8 0x560578de401a in cmd_test tests/builtin-test.c:807
#9 0x560578e49354 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:312
#10 0x560578ce71a8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:364
#11 0x560578ce71a8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:408
#12 0x560578ce71a8 in main /home/namhyung/project/linux/tools/perf/perf.c:538
#13 0x7fecc2b7acc9 in __libc_start_main ../csu/libc-start.c:308
Fixes: cff7f956ec4a1 ("perf tests: Move pmu tests into separate object") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200915031819.386559-12-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 930beb5ac09a ("MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>") forgot
to select the correct MIPS_L1_CACHE_SHIFT for SNI RM. This breaks non
coherent DMA because of a wrong allocation alignment.
When compiling with DEBUG=1 on Fedora 32 I'm getting crash for 'perf
test signal':
Program received signal SIGSEGV, Segmentation fault.
0x0000000000c68548 in __test_function ()
(gdb) bt
#0 0x0000000000c68548 in __test_function ()
#1 0x00000000004d62e9 in test_function () at tests/bp_signal.c:61
#2 0x00000000004d689a in test__bp_signal (test=0xa8e280 <generic_ ...
#3 0x00000000004b7d49 in run_test (test=0xa8e280 <generic_tests+1 ...
#4 0x00000000004b7e7f in test_and_print (t=0xa8e280 <generic_test ...
#5 0x00000000004b8927 in __cmd_test (argc=1, argv=0x7fffffffdce0, ...
...
It's caused by the symbol __test_function being in the ".bss" section:
$ nm perf | grep __test_function 0000000000c68548 B __test_function
I guess most of the time we're just lucky the inline asm ended up in the
".text" section, so making it specific explicit with push and pop
section clauses.
vmbus_wait_for_unload() looks for a CHANNELMSG_UNLOAD_RESPONSE message
coming from Hyper-V. But if the message isn't found for some reason,
the panic path gets hung forever. Add a timeout of 10 seconds to prevent
this.
Fixes: 415719160de3 ("Drivers: hv: vmbus: avoid scheduling in interrupt context in vmbus_initiate_unload()") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1600026449-23651-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This warning was introduced in
commit 81033c6b584b ("ALSA: core: Warn on empty module").
It looks like we are supposed to set card->owner to THIS_MODULE.
A new warning in Clang points out that the initialization of
mux_pll_src_4plls_p appears incorrect:
../drivers/clk/rockchip/clk-rk3228.c:140:58: warning: suspicious
concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Wstring-concatenation]
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
,
../drivers/clk/rockchip/clk-rk3228.c:140:48: note: place parentheses
around the string literal to silence warning
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
1 warning generated.
Given the name of the variable and the same variable name in rv1108, it
seems that this should have been four distinct elements. Fix it up by
adding the comma as suggested.
In Documentation/virt/kvm/api.rst it is said that "You probably want to
use 0 as machine type", which implies that type 0 be the "automatic" or
"default" type. And, in user-space libvirt use the null-machine (with
type 0) to detect the kvm capability, which returns "KVM not supported"
on a VZ platform.
I try to fix it in QEMU but it is ugly:
https://lists.nongnu.org/archive/html/qemu-devel/2020-08/msg05629.html
And Thomas Huth suggests me to change the definition of kvm type:
https://lists.nongnu.org/archive/html/qemu-devel/2020-09/msg03281.html
Since VZ and TE cannot co-exists, using type 0 on a TE platform will
still return success (so old user-space tools have no problems on new
kernels); the advantage is that using type 0 on a VZ platform will not
return failure. So, the only problem is "new user-space tools use type
2 on old kernels", but if we treat this as a kernel bug, we can backport
this patch to old stable kernels.
In the prepare_message callback the bus driver has the
opportunity to split a transfer into smaller chunks.
spi_map_msg is done after prepare_message.
Function spi_res_release releases the splited transfers
in the message. Therefore spi_res_release should be called
after spi_map_msg.
The previous try at this was commit c9ba7a16d0f1
which released the splited transfers after
spi_finalize_current_message had been called.
This introduced a race since the message struct could be
out of scope because the spi_sync call got completed.
Fixes this leak on spi bus driver spi-bcm2835.c when transfer
size is greater than 65532:
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reading past end of file returns EOF for aligned reads but -EINVAL for
unaligned reads on f2fs. While documentation is not strict about this
corner case, most filesystem returns EOF on this case, like iomap
filesystems. This patch consolidates the behavior for f2fs, by making
it return EOF(0).
it can be verified by a read loop on a file that does a partial read
before EOF (A file that doesn't end at an aligned address). The
following code fails on an unaligned file on f2fs, but not on
btrfs, ext4, and xfs.
while (done < total) {
ssize_t delta = pread(fd, buf + done, total - done, off + done);
if (!delta)
break;
...
}
It is arguable whether filesystems should actually return EOF or
-EINVAL, but since iomap filesystems support it, and so does the
original DIO code, it seems reasonable to consolidate on that.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the sbi->ckpt->next_free_nid is not NAT block aligned and if there
are free nids in that NAT block between the start of the block and
next_free_nid, then those free nids will not be scanned in scan_nat_page().
This results into mismatch between nm_i->available_nids and the sum of
nm_i->free_nid_count of all NAT blocks scanned. And nm_i->available_nids
will always be greater than the sum of free nids in all the blocks.
Under this condition, if we use all the currently scanned free nids,
then it will loop forever in f2fs_alloc_nid() as nm_i->available_nids
is still not zero but nm_i->free_nid_count of that partially scanned
NAT block is zero.
Fix this to align the nm_i->next_scan_nid to the first nid of the
corresponding NAT block.
I found this when compiling a kbuild random config with GCC 11. The
config enables CONFIG_DEBUG_SECTION_MISMATCH, which sets CFLAGS
-fno-inline-functions-called-once. This causes the call to cache_loop in
cache.c to not be inlined causing the below compile error.
In file included from arch/openrisc/mm/cache.c:13:
arch/openrisc/mm/cache.c: In function 'cache_loop':
./arch/openrisc/include/asm/spr.h:16:27: warning: 'asm' operand 0 probably does not match constraints
16 | #define mtspr(_spr, _val) __asm__ __volatile__ ( \
| ^~~~~~~
arch/openrisc/mm/cache.c:25:3: note: in expansion of macro 'mtspr'
25 | mtspr(reg, line);
| ^~~~~
./arch/openrisc/include/asm/spr.h:16:27: error: impossible constraint in 'asm'
16 | #define mtspr(_spr, _val) __asm__ __volatile__ ( \
| ^~~~~~~
arch/openrisc/mm/cache.c:25:3: note: in expansion of macro 'mtspr'
25 | mtspr(reg, line);
| ^~~~~
make[1]: *** [scripts/Makefile.build:283: arch/openrisc/mm/cache.o] Error 1
The asm constraint "K" requires a immediate constant argument to mtspr,
however because of no inlining a register argument is passed causing a
failure. Fix this by using __always_inline.
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a write delegation isn't available, the Linux NFS client uses
a zero-stateid when performing a SETATTR.
NFSv4.0 provides no mechanism for an NFS server to match such a
request to a particular client. It recalls all delegations for that
file, even delegations held by the client issuing the request. If
that client happens to hold a read delegation, the server will
recall it immediately, resulting in an NFS4ERR_DELAY/CB_RECALL/
DELEGRETURN sequence.
Optimize out this pipeline bubble by having the client return any
delegations it may hold on a file before it issues a
SETATTR(zero-stateid) on that file.
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...a4321000
spi_msg@ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@ffffffd5a41576f8
len: 131071
tx_buf: ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
If the zero duty cycle doesn't correspond to any voltage in the voltage
table, the PWM regulator returns an -EINVAL from get_voltage_sel() which
results in the core erroring out with a "failed to get the current
voltage" and ending up not applying the machine constraints.
Instead, return -ENOTRECOVERABLE which makes the core set the voltage
since it's at an unknown value.
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Link:
https://lore.kernel.org/r/20200825093940.19612-1-jhasan@marvell.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Javed Hasan <jhasan@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When pm8001_tag_alloc() fails, task should be freed just like it is done in
the subsequent error paths.
Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cn Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A client should be able to handle getting an ERR_DELAY error
while doing a LOCK call to reclaim state due to delegation being
recalled. This is a transient error that can happen due to server
moving its volumes and invalidating its file location cache and
upon reference to it during the LOCK call needing to do an
expensive lookup (leading to an ERR_DELAY error on a PUTFH).
When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.
Fixes: b3bf5666a510 ("hv_netvsc: defer queue selection to VF") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes: 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since transactions may be freed shortly after they're created, before
a log_flush occurs, we need to initialize their ail1 and ail2 lists
earlier. Before this patch, the ail1 list was initialized in gfs2_log_flush().
This moves the initialization to the point when the transaction is first
created.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Reduce sess_lock holding to prevent CPU Lock up. sess_lock was held across
fc_port registration and deletion. These calls can be blocked by upper
layer. Sess_lock is also being accessed by interrupt thread.
- Reduce number of loops in processing work_list to prevent kernel complaint
of CPU lockup or holding sess_lock.
Reported-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Tested-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Fixes: 9ba1cb25c151 ("scsi: qla2xxx: Remove all rports if fabric scan retry fails") Link: https://lore.kernel.org/linux-scsi/D01377DD-2E86-427B-BA0C-8D7649E37870@oracle.com/T/#t Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the rport registration is being called from a single work element
that is used to process QLA internal "work_list". This work_list is meant for
quick and simple task (ie no sleep). The Rport registration process sometime
can be delayed by upper layer. This causes back pressure with the internal
queue where other jobs are unable to move forward.
This patch will schedule the registration process with a new work element
(fc_port.reg_work). While the RPort is being registered, the current state of
the fcport will not move forward until the registration is done. If the state
of the fabric has changed, a new field/next_disc_state will record the next
action on whether to 'DELETE' or 'Reverify the session/ADISC'.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver for Marvell switches puts all ports in IGMP snooping mode
which results in all IGMP/MLD frames that ingress on the ports to be
forwarded to the CPU only.
The bridge code in the kernel can then interpret these frames and act
upon them, for instance by updating the mdb in the switch to reflect
multicast memberships of stations connected to the ports. However,
the IGMP/MLD frames must then also be forwarded to other ports of the
bridge so external IGMP queriers can track membership reports, and
external multicast clients can receive query reports from foreign IGMP
queriers.
Currently, this is impossible as the EDSA tagger sets offload_fwd_mark
on the skb when it unwraps the tagged frames, and that will make the
switchdev layer prevent the skb from egressing on any other port of
the same switch.
To fix that, look at the To_CPU code in the DSA header and make
forwarding of the frame possible for trapped IGMP packets.
Introduce some #defines for the frame types to make the code a bit more
comprehensive.
Signed-off-by: Daniel Mack <daniel@zonque.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using gcov to collect coverage data for kernels compiled with GCC 10.1
causes random malfunctions and kernel crashes. This is the result of a
changed GCOV_COUNTERS value in GCC 10.1 that causes a mismatch between
the layout of the gcov_info structure created by GCC profiling code and
the related structure used by the kernel.
Fix this by updating the in-kernel GCOV_COUNTERS value. Also re-enable
config GCOV_KERNEL for use with GCC 10.
Reported-by: Colin Ian King <colin.king@canonical.com> Reported-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Tested-by: Leon Romanovsky <leonro@nvidia.com> Tested-and-Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB composition, defining the set of exported functions, is dynamic
in newer Quectel modems. Default functions can be disabled and
alternative functions can be enabled instead. The alternatives
includes class functions using interface pairs, which should be
handled by the respective class drivers.
Active interfaces are numbered consecutively, so static
blacklisting based on interface numbers will fail when the
composition changes. An example of such an error, where the
option driver has bound to the CDC ECM data interface,
preventing cdc_ether from handling this function:
Change rules for EC21, EC25, BG96 and EG95 to match vendor specific
serial functions only, to prevent binding to class functions. Require
2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET
network functions.
Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
There were some problem in ipq8074 Gen2 PCIe phy init sequence.
1. Few register values were wrongly updated in the phy init sequence.
2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter
register which is added in serdes table causing the wrong register
was getting updated.
3. Clocks and resets were not added in the phy init.
Fix these to make Gen2 PCIe port on ipq8074 devices to work.
The current implementation for gbcodec_mixer_dapm_ctl_put() uses
uninitialized gbvalue for comparison with updated value. This was found
using static analysis with coverity.
Uninitialized scalar variable (UNINIT)
11. uninit_use: Using uninitialized value
gbvalue.value.integer_value[0].
460 if (gbvalue.value.integer_value[0] != val) {
This patch fixes the issue with fetching the gbvalue before using it for
comparision.
According to SDM 27.2.4, Event delivery causes an APIC-access VM exit.
Don't report internal error and freeze guest when event delivery causes
an APIC-access exit, it is handleable and the event will be re-injected
during the next vmentry.
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1597827327-25055-2-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
Yunhai Zhang recently fixed a VGA software scrollback bug in commit ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
This means that images can be mapped and unmapped (i.e. block devices
can be created and deleted) by a UID 0 process even after it drops all
privileges or by any process with CAP_DAC_OVERRIDE in its user namespace
as long as UID 0 is mapped into that user namespace.
Be consistent with other virtual block devices (loop, nbd, dm, md, etc)
and require CAP_SYS_ADMIN in the initial user namespace for mapping and
unmapping, and also for dumping the configuration string and refreshing
the image header.
Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.
Cc: stable@vger.kernel.org Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TVE200 will occasionally print a bunch of lost interrupts
and similar dmesg messages, sometimes during boot and sometimes
after disabling and coming back to enablement. This is probably
because the hardware is left in an unknown state by the boot
loader that displays a logo.
This can be fixed by bringing the controller into a known state
by resetting the controller while enabling it. We retry reset 5
times like the vendor driver does. We also put the controller
into reset before de-clocking it and clear all interrupts before
enabling the vblank IRQ.
This makes the video enable/disable/enable cycle rock solid
on the D-Link DIR-685. Tested extensively.
1. Initiator A tries to log in to iqn1-tpg1 on port 3260. After finishing
PDU exchange in the login thread and before the negotiation is finished
the the network link goes down. At this point A has not finished login
and tpg->np_login_sem is held.
2. Initiator B tries to log in to iqn2-tpg1 on port 3260. After finishing
PDU exchange in the login thread the target expects to process remaining
login PDUs in workqueue context.
3. Initiator A' tries to log in to iqn1-tpg1 on port 3260 from a new
socket. A' will wait for tpg->np_login_sem with np->np_login_timer
loaded to wait for at most 15 seconds. The lock is held by A so A'
eventually times out.
4. Before A' got timeout initiator B gets negotiation failed and calls
iscsi_target_login_drop()->iscsi_target_login_sess_out(). The
np->np_login_timer is canceled and initiator A' will hang forever.
Because A' is now in the login thread, no new login requests can be
serviced.
Fix this by moving iscsi_stop_login_thread_timer() out of
iscsi_target_login_sess_out(). Also remove iscsi_np parameter from
iscsi_target_login_sess_out().
Link: https://lore.kernel.org/r/20200729130343.24976-1-houpu@bytedance.com Cc: stable@vger.kernel.org Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Hou Pu <houpu@bytedance.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code does not consider 'page_off' in data digest calculation. To
fix this, add a local variable 'first_sg' and set first_sg.offset to
sg->offset + page_off.
Link: https://lore.kernel.org/r/1598358910-3052-1-git-send-email-varun@chelsio.com Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Cc: <stable@vger.kernel.org> Reviewed-by: Mike Christie <michael.christie@oralce.com> Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When faulting in the pages for the user supplied buffer for the search
ioctl, we are passing only the base address of the buffer to the function
fault_in_pages_writeable(). This means that after the first iteration of
the while loop that searches for leaves, when we have a non-zero offset,
stored in 'sk_offset', we try to fault in a wrong page range.
So fix this by adding the offset in 'sk_offset' to the base address of the
user supplied buffer when calling fault_in_pages_writeable().
Several users have reported that the applications compsize and bees have
started to operate incorrectly since commit a48b73eca4ceb9 ("btrfs: fix
potential deadlock in the search ioctl") was added to stable trees, and
these applications make heavy use of the search ioctls. This fixes their
issues.
Link: https://lore.kernel.org/linux-btrfs/632b888d-a3c3-b085-cdf5-f9bb61017d92@lechevalier.se/ Link: https://github.com/kilobyte/compsize/issues/34 Fixes: a48b73eca4ceb9 ("btrfs: fix potential deadlock in the search ioctl") CC: stable@vger.kernel.org # 4.4+ Tested-by: A L <mail@lechevalier.se> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay reported a lockdep splat in generic/476 that I could reproduce
with btrfs/187.
======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2+ #1 Tainted: G W
------------------------------------------------------
kswapd0/100 is trying to acquire lock: ffff9e8ef38b6268 (&delayed_node->mutex){+.+.}-{3:3}, at: __btrfs_release_delayed_node.part.0+0x3f/0x330
but task is already holding lock: ffffffffa9d74700 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x5/0x30
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
This is because we are holding the chunk_mutex when we call
btrfs_alloc_device, which does a GFP_KERNEL allocation. We don't want
to switch that to a GFP_NOFS lock because this is the only place where
it matters. So instead use memalloc_nofs_save() around the allocation
in order to avoid the lockdep splat.
Reported-by: Nikolay Borisov <nborisov@suse.com> CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
A completely sane converted fs will cause kernel warning at balance
time:
[ 1557.188633] BTRFS info (device sda7): relocating block group 8162107392 flags data
[ 1563.358078] BTRFS info (device sda7): found 11722 extents
[ 1563.358277] BTRFS info (device sda7): leaf 7989321728 gen 95 total ptrs 213 free space 3458 owner 2
[ 1563.358280] item 0 key (7984947200 169 0) itemoff 16250 itemsize 33
[ 1563.358281] extent refs 1 gen 90 flags 2
[ 1563.358282] ref#0: tree block backref root 4
[ 1563.358285] item 1 key (7985602560 169 0) itemoff 16217 itemsize 33
[ 1563.358286] extent refs 1 gen 93 flags 258
[ 1563.358287] ref#0: shared block backref parent 7985602560
[ 1563.358288] (parent 7985602560 is NOT ALIGNED to nodesize 16384)
[ 1563.358290] item 2 key (7985635328 169 0) itemoff 16184 itemsize 33
...
[ 1563.358995] BTRFS error (device sda7): eb 7989321728 invalid extent inline ref type 182
[ 1563.358996] ------------[ cut here ]------------
[ 1563.359005] WARNING: CPU: 14 PID: 2930 at 0xffffffff9f231766
Then with transaction abort, and obviously failed to balance the fs.
[CAUSE]
That mentioned inline ref type 182 is completely sane, it's
BTRFS_SHARED_BLOCK_REF_KEY, it's some extra check making kernel to
believe it's invalid.
Commit 64ecdb647ddb ("Btrfs: add one more sanity check for shared ref
type") introduced extra checks for backref type.
One of the requirement is, parent bytenr must be aligned to node size,
which is not correct.
One example is like this:
0 1G 1G+4K 2G 2G+4K
| |///////////////////|//| <- A chunk starts at 1G+4K
| | <- A tree block get reserved at bytenr 1G+4K
Then we have a valid tree block at bytenr 1G+4K, but not aligned to
nodesize (16K).
Such chunk is not ideal, but current kernel can handle it pretty well.
We may warn about such tree block in the future, but should not reject
them.
[FIX]
Change the alignment requirement from node size alignment to sector size
alignment.
Also, to make our lives a little easier, also output @iref when
btrfs_get_extent_inline_ref_type() failed, so we can locate the item
easier.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205475 Fixes: 64ecdb647ddb ("Btrfs: add one more sanity check for shared ref type") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com>
[ update comments and messages ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
let's use usb_find_common_endpoints() to discover endpoints, it does all
necessary checks for type and xfer direction
remove memset() in hfa384x_create(), because we now assign endpoints in
prism2sta_probe_usb() and because create_wlan() uses kzalloc() to
allocate hfa384x struct before calling hfa384x_create()
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack. As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The additional forcing of the 8 byte alignment of the timestamp
is not strictly necessary but makes the code less fragile by
making this explicit.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The force alignment of ts is not strictly necessary in this particularly
case but does make the code less fragile.
iio_push_to_buffers_with_timestamp assumes 8 byte alignment which
is not guaranteed by an array of smaller elements.
Note that whilst in this particular case the alignment forcing
of the ts element is not strictly necessary it acts as good
documentation. Doing this where not necessary should cut
down on the number of cut and paste introduced errors elsewhere.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
The explicit alignment of ts is necessary to ensure consistent
padding for x86_32 in which the ts would otherwise be 4 byte aligned.
Fixes: 283d26917ad6 ("iio: chemical: ccs811: Add triggered buffer support") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak appart
from previous readings.
It is necessary to force the alignment of ts to avoid the padding
on x86_32 being different from 64 bit platorms (it alows for
4 bytes aligned 8 byte types.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case as by
coincidence the padding will end up the same, however I consider
it to make the code less fragile and have included it.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The explicit alignment of ts is necessary to ensure correct padding
on architectures where s64 is only 4 bytes aligned such as x86_32.
Fixes: a9e9c7153e96 ("iio: adc: add max1117/max1118/max1119 ADC driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de> Cc: Marc Titinger <mtitinger@baylibre.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The force alignment of ts is not strictly necessary in this case
but reduces the fragility of the code.
Fixes: 3691e5a69449 ("iio: adc: add driver for the ti-adc084s021 chip") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Mårten Lindahl <martenli@axis.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by moving
to a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
Fixes tag is beyond some major refactoring so likely manual backporting
would be needed to get that far back.
Whilst the force alignment of the ts is not strictly necessary, it
does make the code less fragile.
Fixes: 3bbec9773389 ("iio: bmc150_accel: add support for hardware fifo") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here we use a structure on the stack. The driver already did an
explicit memset so no data leak was possible.
Forced alignment of ts is not strictly necessary but probably makes
the code slightly less fragile.
Note there has been some rework in this driver of the years, so no
way this will apply cleanly all the way back.
To stop conversion ads1015_set_power_state() function call unimplemented
function __pm_runtime_suspend() from pm_runtime_put_autosuspend()
if CONFIG_PM is not set.
In case of CONFIG_PM is not set: __pm_runtime_suspend() returns -ENOSYS,
so ads1015_read_raw() failed because ads1015_set_power_state() returns an
error.
If CONFIG_PM is disabled, there is no need to start/stop conversion.
Fix it by adding return 0 function variant if CONFIG_PM is not set.
Locking should be held for the entire reading sequence involving setting
the channel, waiting for the channel switch and reading from the
channel.
If not, reading from a channel can result mixing with the reading from
another channel.
Fixes: 07914c84ba30 ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC") Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com> Link: https://lore.kernel.org/r/20200819075525.1395248-1-angelo.compagnucci@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When memory encryption is active the device is likely not in a direct
mapped domain. Forbid using IOMMUv2 functionality for now until finer
grained checks for this have been implemented.
On my R9 390, the voltage was reported as a constant 1000 mV.
This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor()
function, where some magic constants were used in a condition,
to determine whether the voltage should be read from PLANE2_VID
or PLANE1_VID. The VDDC mask was incorrectly used, instead of
the VDDGFX mask.
This patch changes the code to use the correct defined constants
(and apply the correct bitshift), thus resulting in correct voltage reporting.
In snd_hdac_device_init pm_runtime_set_active is called to
increase child_count in parent device. But when it is failed
to build connection with GPU for one case that integrated
graphic gpu is disabled, snd_hdac_ext_bus_device_exit will be
invoked to clean up a HD-audio extended codec base device. At
this time the child_count of parent is not decreased, which
makes parent device can't get suspended.
This patch calls pm_runtime_set_suspended to decrease child_count
in parent device in snd_hdac_device_exit to match with
snd_hdac_device_init. pm_runtime_set_suspended can make sure that
it will not decrease child_count if the device is already suspended.
This fixes the behavior of the scaling_max_freq and scaling_min_freq
sysfs files in systems which had turbo disabled by the BIOS.
Caleb noticed that the HWP is programmed to operate in the wrong
P-state range on his system when the CPUFREQ policy min/max frequency
is set via sysfs. This seems to be because in his system
intel_pstate_get_hwp_max() is returning the maximum turbo P-state even
though turbo was disabled by the BIOS, which causes intel_pstate to
scale kHz frequencies incorrectly e.g. setting the maximum turbo
frequency whenever the maximum guaranteed frequency is requested via
sysfs.
Tested-by: Caleb Callaway <caleb.callaway@intel.com> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor subject edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit f6ebbcf08f37 ("cpufreq: intel_pstate: Implement passive
mode with HWP enabled") it is possible to change the driver status
to "off" via sysfs with HWP enabled, which effectively causes the
driver to unregister itself, but HWP remains active and it forces the
minimum performance, so even if another cpufreq driver is loaded,
it will not be able to control the CPU frequency.
For this reason, make the driver refuse to change the status to
"off" with HWP enabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HSDK board has Micrel KSZ9031, recent commit bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.
When input_mt_init_slots() fails, input should be freed
to prevent memleak. When input_register_device() fails,
we should call input_mt_destroy_slots() to free memory
allocated by input_mt_init_slots().