When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") Cc: stable@vger.kernel.org
Depends-on: 5afced3bf281 ("writeback: Avoid skipping inode writeback") Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org Suggested-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only use of I_DIRTY_TIME_EXPIRE is to detect in
__writeback_single_inode() that inode got there because flush worker
decided it's time to writeback the dirty inode time stamps (either
because we are syncing or because of age). However we can detect this
directly in __writeback_single_inode() and there's no need for the
strange propagation with I_DIRTY_TIME_EXPIRE flag.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise a malicious user could (ab)use the "recalculate" feature
that makes dm-integrity calculate the checksums in the background
while the device is already usable. When the system restarts before all
checksums have been calculated, the calculation continues where it was
interrupted even if the recalculate feature is not requested the next
time the dm device is set up.
Disable recalculating if we use internal_hash or journal_hash with a
key (e.g. HMAC) and we don't have the "legacy_recalculate" flag.
This may break activation of a volume, created by an older kernel,
that is not yet fully recalculated -- if this happens, the user should
add the "legacy_recalculate" flag to constructor parameters.
Cc: stable@vger.kernel.org Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Daniel Glockner <dg@emlix.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below race can come, if trace_open and resize of
cpu buffer is running parallely on different cpus
CPUX CPUY
ring_buffer_resize
atomic_read(&buffer->resize_disabled)
tracing_open
tracing_reset_online_cpus
ring_buffer_reset_cpu
rb_reset_cpu
rb_update_pages
remove/insert pages
resetting pointer
This race can cause data abort or some times infinte loop in
rb_remove_pages and rb_insert_pages while checking pages
for sanity.
Take buffer lock to fix this.
Link: https://lkml.kernel.org/r/1601976833-24377-1-git-send-email-gkohli@codeaurora.org Cc: stable@vger.kernel.org Fixes: 83f40318dab00 ("ring-buffer: Make removal of ring buffer pages atomic") Reported-by: Denis Efremov <efremov@linux.com> Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent commit to fix a memory leak introduced an inadvertant NULL
pointer dereference. The `wacom_wac->pen_fifo` variable was never
intialized, resuling in a crash whenever functions tried to use it.
Since the FIFO is only used by AES pens (to buffer events from pen
proximity until the hardware reports the pen serial number) this would
have been easily overlooked without testing an AES device.
This patch converts `wacom_wac->pen_fifo` over to a pointer (since the
call to `devres_alloc` allocates memory for us) and ensures that we assign
it to point to the allocated and initalized `pen_fifo` before the function
returns.
fixup_pi_state_owner() tries to ensure that the state of the rtmutex,
pi_state and the user space value related to the PI futex are consistent
before returning to user space. In case that the user space value update
faults and the fault cannot be resolved by faulting the page in via
fault_in_user_writeable() the function returns with -EFAULT and leaves
the rtmutex and pi_state owner state inconsistent.
A subsequent futex_unlock_pi() operates on the inconsistent pi_state and
releases the rtmutex despite not owning it which can corrupt the RB tree of
the rtmutex and cause a subsequent kernel stack use after free.
It was suggested to loop forever in fixup_pi_state_owner() if the fault
cannot be resolved, but that results in runaway tasks which is especially
undesired when the problem happens due to a programming error and not due
to malice.
As the user space value cannot be fixed up, the proper solution is to make
the rtmutex and the pi_state consistent so both have the same owner. This
leaves the user space value out of sync. Any subsequent operation on the
futex will fail because the 10th rule of PI futexes (pi_state owner and
user space value are consistent) has been violated.
As a consequence this removes the inept attempts of 'fixing' the situation
in case that the current task owns the rtmutex when returning with an
unresolvable fault by unlocking the rtmutex which left pi_state::owner and
rtmutex::owner out of sync in a different and only slightly less dangerous
way.
Fixes: 1b7558e457ed ("futexes: fix fault handling in futex_lock_pi") Reported-by: gzobqq@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updating pi_state::owner is done at several places with the same
code. Provide a function for it and use that at the obvious places.
This is also a preparation for a bug fix to avoid yet another copy of the
same code or alternatively introducing a completely unpenetratable mess of
gotos.
Originally-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If that unexpected case of inconsistent arguments ever happens then the
futex state is left completely inconsistent and the printk is not really
helpful. Replace it with a warning and make the state consistent.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case that futex_lock_pi() was aborted by a signal or a timeout and the
task returned without acquiring the rtmutex, but is the designated owner of
the futex due to a concurrent futex_unlock_pi() fixup_owner() is invoked to
establish consistent state. In that case it invokes fixup_pi_state_owner()
which in turn tries to acquire the rtmutex again. If that succeeds then it
does not propagate this success to fixup_owner() and futex_lock_pi()
returns -EINTR or -ETIMEOUT despite having the futex locked.
Return success from fixup_pi_state_owner() in all cases where the current
task owns the rtmutex and therefore the futex and propagate it correctly
through fixup_owner(). Fixup the other callsite which does not expect a
positive return value.
Fixes: c1e2f0eaf015 ("futex: Avoid violating the 10th rule of futex") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--> preemption (unrelated wakeup of some other higher prio task, e.g. timer)
switch_to(other_task)
return to user
sys_futex()
loop infinite as above
Just for the fun of it the futex exit cleanup could trigger the wakeup
itself before the task sets its futex state to DEAD.
To cure this, the handling of the exiting owner is changed so:
- A refcount is held on the task
- The task pointer is stored in a caller visible location
- The caller drops all locks (hash bucket, mmap_sem) and blocks
on task::futex_exit_mutex. When the mutex is acquired then
the exiting task has completed the cleanup and the state
is consistent and can be reevaluated.
This is not a pretty solution, but there is no choice other than returning
an error code to user space, which would break the state consistency
guarantee and open another can of problems including regressions.
For stable backports the preparatory commits ac31c7ff8624 .. ba31c1a48538
are required as well, but for anything older than 5.3.y the backports are
going to be provided when this hits mainline as the other dependencies for
those kernels are definitely not stable material.
Fixes: 778e9a9c3e71 ("pi-futex: fix exit races and locking problems") Reported-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Stable Team <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20191106224557.041676471@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mutex will be used in subsequent changes to replace the busy looping of
a waiter when the futex owner is currently executing the exit cleanup to
prevent a potential live lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.845798895@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
exec() attempts to handle potentially held futexes gracefully by running
the futex exit handling code like exit() does.
The current implementation has no protection against concurrent incoming
waiters. The reason is that the futex state cannot be set to
FUTEX_STATE_DEAD after the cleanup because the task struct is still active
and just about to execute the new binary.
While its arguably buggy when a task holds a futex over exec(), for
consistency sake the state handling can at least cover the actual futex
exit cleanup section. This provides state consistency protection accross
the cleanup. As the futex state of the task becomes FUTEX_STATE_OK after the
cleanup has been finished, this cannot prevent subsequent attempts to
attach to the task in case that the cleanup was not successfull in mopping
up all leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.753355618@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of relying on PF_EXITING use an explicit state for the futex exit
and set it in the futex exit function. This moves the smp barrier and the
lock/unlock serialization into the futex code.
As with the DEAD state this is restricted to the exit path as exec
continues to use the same task struct.
This allows to simplify that logic in a next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.539409004@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting task::futex_state in do_exit() is rather arbitrarily placed for no
reason. Move it into the futex code.
Note, this is only done for the exit cleanup as the exec cleanup cannot set
the state to FUTEX_STATE_DEAD because the task struct is still in active
use.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.439511191@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow separate handling of the futex exit state in the futex exit code
for exit and exec, split futex_mm_release() into two functions and invoke
them from the corresponding exit/exec_mm_release() callsites.
Preparatory only, no functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.332094221@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The futex exit handling relies on PF_ flags. That's suboptimal as it
requires a smp_mb() and an ugly lock/unlock of the exiting tasks pi_lock in
the middle of do_exit() to enforce the observability of PF_EXITING in the
futex code.
Add a futex_state member to task_struct and convert the PF_EXITPIDONE logic
over to the new state. The PF_EXITING dependency will be cleaned up in a
later step.
This prepares for handling various futex exit issues later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.149449274@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The futex exit handling is #ifdeffed into mm_release() which is not pretty
to begin with. But upcoming changes to address futex exit races need to add
more functionality to this exit code.
Split it out into a function, move it into futex code and make the various
futex exit functions static.
Preparatory only and no functional change.
Folded build fix from Borislav.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.049705556@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes: 7afb3e575e5a ("net: mscc: ocelot: don't handle netdev events for other netdevs") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5a7 ("net/ipv6: Save route type in rt6_info") Signed-off-by: Matteo Croce <mcroce@microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db796 ("udp: perform source validation for mcast early demux") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com Fixes: 0207df4fa1a86 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN") Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: YJ Chiang <yj.chiang@mediatek.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3226b158e67c ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff70ce453 ("sh_eth: Fix sleeping function called from invalid context") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed77f
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1a9
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Reported-by: Stephan Gerhold <stephan@gerhold.net> Tested-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com> Cc: <stable@vger.kernel.org> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vhub engine has two dma mode, one is descriptor list, another
is single stage DMA. Each mode has different stop register setting.
Descriptor list operation (bit2) : 0 disable reset, 1: enable reset
Single mode operation (bit0) : 0 : disable, 1: enable
Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub") Cc: stable <stable@vger.kernel.org> Acked-by: Felipe Balbi <balbi@kernel.org> Acked-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com> Link: https://lore.kernel.org/r/20210108081238.10199-2-ryan_chen@aspeedtech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Commit c685af1108d7 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
In stm_heartbeat_init(): return value gets reset after the first
iteration by stm_source_register_device(), so allocation failures
after that will, after a clean up, return success. Fix that.
Fixes: 119291853038 ("stm class: Add heartbeat stm source device") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hui <john.wanghui@huawei.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: https://lore.kernel.org/r/20210115195917.3184-2-alexander.shishkin@linux.intel.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 55567976629e ("genirq/irqdomain: Allow partial trimming of
irq_data hierarchy") the irq_data chain is valided.
The irq_domain_trim_hierarchy() function doesn't consider the irq + ipi
domain hierarchy as valid, since the ipi domain has the irq domain set
as parent, but the parent domain has no chip set. Hence the boot ends in
a kernel panic.
Set the chip for the parent domain as it is done in the mips gic irq
driver, to have a valid irq_data chain.
The power-down mask of the ad5504 is actually a power-up mask. Meaning if
a bit is set the corresponding channel is powered up and if it is not set
the channel is powered down.
The driver currently has this the wrong way around, resulting in the
channel being powered up when requested to be powered down and vice versa.
Fixes: 3bbbf150ffde ("staging:iio:dac:ad5504: Use strtobool for boolean values") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20201209104649.5794-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After calling peak_usb_netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the peak_usb_netif_rx_ni().
Reordering the lines solves the issue.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/r/20210120114137.200019-4-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the canfd_frame cfd which aliases skb memory is accessed
after the netif_rx_ni().
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/r/20210120114137.200019-3-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the netif_rx_ni() in:
stats->rx_bytes += cf->len;
Reordering the lines solves the issue.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface") Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous test added an address with a specified metric and check if
correspond route was created. I somehow added two logs for the same
test. Remove the duplicated one.
Reported-by: Antoine Tenart <atenart@redhat.com> Fixes: 0d29169a708b ("selftests/net/fib_tests: update addr_metric_test for peer route testing") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20210119025930.2810532-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
THe HP Stream x360 Convertible PC 11 DSDT has the following VGBS function:
Method (VGBS, 0, Serialized)
{
If ((^^PCI0.LPCB.EC0.ROLS == Zero))
{
VBDS = Zero
}
Else
{
VBDS = Zero
}
Return (VBDS) /* \_SB_.VGBI.VBDS */
}
Which is obviously wrong, because it always returns 0 independent of the
2-in-1 being in laptop or tablet mode. This causes the intel-vbtn driver
to initially report SW_TABLET_MODE = 1 to userspace, which is known to
cause problems when the 2-in-1 is actually in laptop mode.
During earlier testing this turned out to not be a problem because the
2-in-1 would do a Notify(..., 0xCC) or Notify(..., 0xCD) soon after
the intel-vbtn driver loaded, correcting the SW_TABLET_MODE state.
Further testing however has shown that this Notify() soon after the
intel-vbtn driver loads, does not always happen. When the Notify
does not happen, then intel-vbtn reports SW_TABLET_MODE = 1 resulting in
a non-working touchpad.
IOW the tablet-mode reporting is not reliable on this device, so it
should be dropped from the allow-list, fixing the touchpad sometimes
not working.
Fixes: 8169bd3e6e19 ("platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting") Link: https://lore.kernel.org/r/20210114143432.31750-1-hdegoede@redhat.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Phil Oester reported that a fix for a possible buffer overrun that I sent
caused a regression that manifests in this output:
Event Message: A PCI parity error was detected on a component at bus 0 device 5 function 0.
Severity: Critical
Message ID: PCI1308
The original code tried to handle the sense data pointer differently when
using 32-bit 64-bit DMA addressing, which would lead to a 32-bit dma_addr_t
value of 0x11223344 to get stored
In my patch, I tried to ensure that the same value is used on both 32-bit
and 64-bit kernels, and picked what seemed to be the most sensible
combination, storing 32-bit addresses in the first four bytes (as 32-bit
kernels already did), and 64-bit addresses in eight consecutive bytes (as
64-bit kernels already did), but evidently this was incorrect.
Always storing the dma_addr_t pointer as 64-bit little-endian,
i.e. initializing the second four bytes to zero in case of 32-bit
addressing, apparently solved the problem for Phil, and is consistent with
what all 64-bit little-endian machines did before.
I also checked in the history that in previous versions of the code, the
pointer was always in the first four bytes without padding, and that
previous attempts to fix 64-bit user space, big-endian architectures and
64-bit DMA were clearly flawed and seem to have introduced made this worse.
Link: https://lore.kernel.org/r/20210104234137.438275-1-arnd@kernel.org Fixes: 381d34e376e3 ("scsi: megaraid_sas: Check user-provided offsets") Fixes: 107a60dd71b5 ("scsi: megaraid_sas: Add support for 64bit consistent DMA") Fixes: 94cd65ddf4d7 ("[SCSI] megaraid_sas: addded support for big endian architecture") Fixes: 7b2519afa1ab ("[SCSI] megaraid_sas: fix 64 bit sense pointer truncation") Reported-by: Phil Oester <kernel@linuxace.com> Tested-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue has generally been covered up by the presence of additional
expansion ROMs after the ones we're interested in, with header fetches
of subsequent images loading enough of the ROM to hide the issue.
Noticed on GA102, which lacks a type 0x70 image compared to TU102,.
[ 906.364197] nouveau 0000:09:00.0: bios: 00000000: type 00, 65024 bytes
[ 906.381205] nouveau 0000:09:00.0: bios: 0000fe00: type 03, 91648 bytes
[ 906.405213] nouveau 0000:09:00.0: bios: 00026400: type e0, 22016 bytes
[ 906.410984] nouveau 0000:09:00.0: bios: 0002ba00: type e0, 366080 bytes
vs
[ 22.961901] nouveau 0000:09:00.0: bios: 00000000: type 00, 60416 bytes
[ 22.984174] nouveau 0000:09:00.0: bios: 0000ec00: type 03, 71168 bytes
[ 23.010446] nouveau 0000:09:00.0: bios: 00020200: type e0, 48128 bytes
[ 23.028220] nouveau 0000:09:00.0: bios: 0002be00: type e0, 140800 bytes
[ 23.080196] nouveau 0000:09:00.0: bios: 0004e400: type 70, 7168 bytes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current implementation defaults the hda clocks to clk_m. This causes hda
to run too slow to operate correctly. Fix this by defaulting to pll_p and
setting the frequency to the correct rate.
This matches upstream t124 and downstream t30.
Acked-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Ion Agorria <ion@agorria.com> Acked-by: Sameer Pujar <spujar@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Link: https://lore.kernel.org/r/20210108135913.2421585-2-pgwipeout@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If of_clk_init() is not called in time_init(), clock providers defined
in the system device tree are not initialized, resulting in failures for
other devices to initialize due to missing clocks.
Similarly to other architectures and to the default kernel time_init()
implementation, call of_clk_init() before executing timer_probe() in
time_init().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.
Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.org Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
haswell machine board is missing pm_ops what prevents it from undergoing
suspend-resume procedure successfully. Assign default snd_soc_pm_ops so
this is no longer the case.
This reverts commit 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()")
dm_get_dev_t() is just used to convert an arbitrary 'path' string
into a dev_t. It doesn't presume that the device is present; that
check will be done later, as the only caller is dm_get_device(),
which does a dm_get_table_device() later on, which will properly
open the device.
So if the path string already _is_ in major:minor representation
we can convert it directly, avoiding a recursion into the filesystem
to lookup the block device.
This avoids a hang in multipath_message() when the filesystem is
inaccessible.
Fixes: 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()") Cc: stable@vger.kernel.org Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
If extended CSD was not available, the eMMC driver would incorrectly
set the block size to 0, as the data_sector_size field of ext_csd
was never initialized. This issue was exposed by commit 817046ecddbc
("block: Align max_hw_sectors to logical blocksize") which caused
max_sectors and max_hw_sectors to be set to 0 after setting the block
size to 0, resulting in a kernel panic in bio_split when attempting
to read from the device. Fix it by only reading the block size from
ext_csd if it is available.
Set the acpi_device pointer which acpi_bus_get_device() returns-by-
reference to NULL on errors.
We've recently had 2 cases where callers of acpi_bus_get_device()
did not properly error check the return value, so set the returned-
by-reference acpi_device pointer to NULL, because at least some
callers of acpi_bus_get_device() expect that to be done on errors.
[ rjw: This issue was exposed by commit 71da201f38df ("ACPI: scan:
Defer enumeration of devices with _DEP lists") which caused it to
be much more likely to occur on some systems, but the real defect
had been introduced by an earlier commit. ]
Fixes: 40e7fcb19293 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA") Fixes: bcfcd409d4db ("usb: split code locating ACPI companion into port and device") Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Diagnosed-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: All applicable <stable@vger.kernel.org>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turned out that VIA codecs also mute the sound in the lowest mixer
level. Turn on the dac_min_mute flag to indicate the mute-as-minimum
in TLV like already done in Conexant and IDT codecs.
snd_seq_oss_synth_make_info() didn't check the error code from
snd_seq_oss_midi_make_info(), and this leads to the call of strlcpy()
with the uninitialized string as the source, which may lead to the
access over the limit.
Add the proper error check for avoiding the failure.
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054a4 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This worked before, because we made all callers name their next pointer
"next". But in trying to be more "drop-in" ready, the silliness here is
revealed. This commit fixes the problem by making the macro argument and
the member use different names.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the continual effort to remove direct usage of skb->next and
skb->prev, this patch adds a helper for iterating through the
singly-linked variant of skb lists, which are used for lists of GSO
packet. The name "skb_list_..." has been chosen to match the existing
function, "kfree_skb_list, which also operates on these singly-linked
lists, and the "..._walk_safe" part is the same idiom as elsewhere in
the kernel.
This patch removes the helper from wireguard and puts it into
linux/skbuff.h, while making it a bit more robust for general usage. In
particular, parenthesis are added around the macro argument usage, and it
now accounts for trying to iterate through an already-null skb pointer,
which will simply run the iteration zero times. This latter enhancement
means it can be used to replace both do { ... } while and while (...)
open-coded idioms.
This should take care of these three possible usages, which match all
current methods of iterations.
Gcc appears to generate efficient code for each of these.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ Just the skbuff.h changes for backporting - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer list can have zero skb as following path:
tipc_named_node_up()->tipc_node_xmit()->tipc_link_xmit(), so
we need to check the list before casting an &sk_buff.
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca7d ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()") Reported-by: Tom Rix <trix@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd363 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Greg Thelen <gthelen@google.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit c269a24ce057 ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com Fixes: e2f1f072db8d ("sit: allow to configure 6rd tunnels via netlink") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the original mtu is not used when the mtu is updated,
the mtu is aligned with cache, this will get an incorrect.
For example, if you want to configure the mtu to be 1500,
but mtu 1536 is configured in fact.
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
As it happens, we used READ_ONCE() to read the state a few lines above the
unmarked read in rxrpc_input_data(), so use that value rather than
re-reading it.
In commit 826f328e2b7e ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver") Fixes: 826f328e2b7e ("net: dcb: Validate netlink message in DCB handler") Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1baa ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()") Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packet Processor hardware not connected to MAC flow control unit and
cannot support TX flow control.
This patch disable flow control support.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Stefan Chulski <stefanc@marvell.com> Acked-by: Marcin Wojtas <mw@semihalf.com> Link: https://lore.kernel.org/r/1610306582-16641-1-git-send-email-stefanc@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log