The return value of hga_card_detect() is not properly handled causing
the probe to succeed even though hga_card_detect() failed. Since probe
succeeds, hgafb_open() can be called which will end up operating on an
unmapped hga_vram. This results in an out-of-bounds access as reported
by kernel test robot [1].
To fix this, correctly detect failure of hga_card_detect() by checking
for a non-zero error code.
syzbot is reporting OOB write at vga16fb_imageblit() [1], for
resize_screen() from ioctl(VT_RESIZE) returns 0 without checking whether
requested rows/columns fit the amount of memory reserved for the graphical
screen if current mode is KD_GRAPHICS.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d0763361b ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e400b6ec4ede ("vt/vgacon: Check if screen resize request comes from userspace") Cc: stable@vger.kernel.org # v2.6.24+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qlcnic_dl_lb_test() currently calls netdev_alloc_skb()
without checking afterwards that the allocation succeeded. Fix this by
checking if the skb is NULL and returning an error in such a case.
Breaking out of the loop if the skb is NULL is not correct as no error
would be reported to the caller and no message would be printed for the
user.
Check return value of lp5xx_read and if non-zero, jump to code at end of
the function, causing lp5523_stop_all_engines to be executed before
returning the error value up the call chain. This fixes the original
commit (248b57015f35) which was reverted due to the University of Minnesota
problems.
If alloc_workqueue() fails, properly catch this and propagate the error
to the calling functions, so that the devuce initialization will
properly error out.
Move ufshcd_set_variant call in ufs_hisi_init_common to common error
section at end of the function, and then jump to this from the error
checking statements for both devm_reset_control_get and
ufs_hisi_get_resource. This fixes the original commit (63a06181d7ce)
which was reverted due to the University of Minnesota problems.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Avri Altman <avri.altman@wdc.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phillip Potter <phil@philpotter.co.uk> Link: https://lore.kernel.org/r/20210503115736.2104747-32-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case clk_prepare() fails, capture and propagate the error code up the
stack. If regulator_enable() was called earlier, properly unwind it by
calling regulator_disable().
niu_pci_eeprom_read() may fail, so add checks to its return value and
propagate the error up the callstack.
An examination of the callstack up to niu_pci_eeprom_read shows that:
niu_pci_eeprom_read() // returns int
niu_pci_vpd_scan_props() // returns int
niu_pci_vpd_fetch() // returns *void*
niu_get_invariants() // returns int
since niu_pci_vpd_fetch() returns void which breaks the bubbling up,
change its return type to int so that error is propagated upwards.
Signed-off-by: Du Cheng <ducheng2@gmail.com> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-24-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change here was incorrect. While it is nice to check if
niu_pci_eeprom_read() succeeded or not when using the data, any error
that might have happened was not propagated upwards properly, causing
the kernel to assume that these reads were successful, which results in
invalid data in the buffer that was to contain the successfully read
data.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Fixes: 26fd962bde0b ("niu: fix missing checks of niu_pci_eeprom_read") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-23-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit does not properly detect if an error happens because the
logic after this loop will not detect that there was a failed
allocation.
Cc: Aditya Pakki <pakki001@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: 5bf7295fe34a ("qlcnic: Avoid potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-25-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Bryan Brattlof <hello@bryanbrattlof.com> Fixes: 765976285a8c ("rtlwifi: fix a potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all as
the media core already prevents memory disclosure on this codepath, so
just drop the extra memset happening here.
As Peter points out, if we were to disconnect and then reconnect this
driver from a device, the "global" state of the device would contain odd
values and could cause problems. Fix this up by just initializing the
whole thing to 0 at probe() time.
Ideally this would be a per-device variable, but given the age and the
total lack of users of it, that would require a lot of s/./->/g changes
for really no good reason.
Reported-by: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Reviewed-by: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/YJP2j6AU82MqEY2M@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fields, "toc" and "cd_info", of "struct gdrom_unit gd" are allocated
in "probe_gdrom()". Prevent a memory leak by making sure "gd.cd_info" is
deallocated in the "remove_gdrom()" function.
Also prevent double free of the field "gd.toc" by moving it from the
module's exit function to "remove_gdrom()". This is because, in
"probe_gdrom()", the function makes sure to deallocate "gd.toc" in case
of any errors, so the exit function invoked later would again free
"gd.toc".
The patch also maintains consistency by deallocating the above mentioned
fields in "remove_gdrom()" along with another memory allocated field
"gd.disk".
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Because of this, all submissions from this group must be reverted from
the kernel tree and will need to be re-reviewed again to determine if
they actually are a valid fix. Until that work is complete, remove this
change to ensure that no problems are being introduced into the
codebase.
Cc: Wenwen Wang <wang6495@umn.edu> Cc: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Fixes: 093c48213ee3 ("gdrom: fix a memory leak bug") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-27-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit is incorrect, it does not properly clean up on the
error path, so I'll keep the revert and fix it up properly with a
follow-on patch.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Avri Altman <avri.altman@wdc.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Fixes: 63a06181d7ce ("scsi: ufs: fix a missing check of devm_reset_control_get") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-31-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit log for this change was incorrect, no "error
handling code" was added, things will blow up just as badly as before if
any of these cases ever were true. As this BUG_ON() never fired, and
most of these checks are "obviously" never going to be true, let's just
revert to the original code for now until this gets unwound to be done
correctly in the future.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here, while technically correct, did not fully
handle all of the reported issues that the commit stated it was fixing,
so revert it until it can be "fixed" fully.
Note, ioremap() probably will never fail for old hardware like this, and
if anyone actually used this hardware (a PowerMac era PCI display card),
they would not be using fbdev anymore.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu> Fixes: 9aa3aa15f4c2 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe") Cc: stable <stable@vger.kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit does not properly unwind if there is an error
condition so it needs to be reverted at this point in time.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: stable <stable@vger.kernel.org> Fixes: 248b57015f35 ("leds: lp5523: fix a missing check of return value of lp55xx_read") Link: https://lore.kernel.org/r/20210503115736.2104747-9-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: f86a3b83833e ("net: stmicro: fix a missing check of clk_prepare") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This patch "looks" correct, but the driver keeps on running and will
fail horribly right afterward if this error condition ever trips.
So points for trying to resolve an issue, but a huge NEGATIVE value for
providing a "fake" fix for the problem as nothing actually got resolved
at all. I'll go fix this up properly...
modprobe brd rd_size=1048576
dmsetup create o --table "0 `blockdev --getsize /dev/ram0` snapshot-origin /dev/ram0"
dmsetup create s --table "0 `blockdev --getsize /dev/ram0` snapshot /dev/ram0 /dev/ram1 N 0"
The reason is that when we test for zero chunk size, we jump to the label
bad_read_metadata without setting the "r" variable. The function
snapshot_ctr destroys all the structures and then exits with "r == 0". The
kernel then crashes because it falsely believes that snapshot_ctr
succeeded.
In order to fix the bug, we set the variable "r" to -EINVAL.
When multiple PCI devices get assigned to a guest right at boot, libxl
incrementally populates the backend tree. The writes for the first of
the devices trigger the backend watch. In turn xen_pcibk_setup_backend()
will set the XenBus state to Initialised, at which point no further
reconfigures would happen unless a device got hotplugged. Arrange for
reconfigure to also get triggered from the backend watch handler.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: stable@vger.kernel.org Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/2337cbd6-94b9-4187-9862-c03ea12e0c61@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be not be needed at all as the
change was useless because this function can only be called when
of_match_device matched on something. So it should be reverted.
In case create_workqueue() fails, release all resources and return -ENOMEM
to caller to avoid potential NULL pointer deref later. Move up the
create_workequeue() call to return early and avoid unwinding the call to
riocm_rx_fill().
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit has a memory leak on the error path here, it does
not clean up everything properly.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Fixes: 23015b22e47c ("rapidio: fix a NULL pointer dereference when create_workqueue() fails") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-45-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ubuntu users reported an audio bug on the Lenovo Yoga Slim 7 14IIL05,
he installed dual OS (Windows + Linux), if he booted to the Linux
from Windows, the Speaker can't work well, it has crackling noise,
if he poweroff the machine first after Windows, the Speaker worked
well.
Before rebooting or shutdown from Windows, the Windows changes the
codec eapd coeff value, but the BIOS doesn't re-initialize its value,
when booting into the Linux from Windows, the eapd coeff value is not
correct. To fix it, set the codec default value to that coeff register
in the alsa driver.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit message for this change was incorrect as the code
path can never result in a NULL dereference, alluding to the fact that
whatever tool was used to "find this" is broken. It's just an optional
resource reservation, so removing this check is fine.
Cc: Kangjie Lu <kjlu@umn.edu> Acked-by: Takashi Iwai <tiwai@suse.de> Fixes: dcd0feac9bab ("ALSA: sb8: add a check for request_region") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-35-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mackie d.2 has an extension card for IEEE 1394 communication, which uses
BridgeCo DM1000 ASIC. On the other hand, Mackie d.4 Pro has built-in
function for IEEE 1394 communication by Oxford Semiconductor OXFW971,
according to schematic diagram available in Mackie website. Although I
misunderstood that Mackie d.2 Pro would be also a model with OXFW971,
it's wrong. Mackie d.2 Pro is a model which includes the extension card
as factory settings.
This commit fixes entries in Kconfig and comment in ALSA OXFW driver.
Cc: <stable@vger.kernel.org> Fixes: fd6f4b0dc167 ("ALSA: bebob: Add skelton for BeBoB based devices") Fixes: ec4dba5053e1 ("ALSA: oxfw: Add support for Behringer/Mackie devices") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20210513125652.110249-3-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usbmidi_get_ms_info() may access beyond the border when a
malformed descriptor is passed. This patch adds the sanity checks of
the given MS endpoint descriptors, and skips invalid ones.
Alesis iO 26 FireWire has two pairs of digital optical interface. It
delivers PCM frames from the interfaces by second isochronous packet
streaming. Although both of the interfaces are available at 44.1/48.0
kHz, first one of them is only available at 88.2/96.0 kHz. It reduces
the number of PCM samples to 4 in Multi Bit Linear Audio data channel
of data blocks on the second isochronous packet streaming.
This commit fixes hardcoded stream formats.
Cc: <stable@vger.kernel.org> Fixes: 28b208f600a3 ("ALSA: dice: add parameters of stream formats for models produced by Alesis") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20210513125652.110249-2-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initialization of MIDI devices that are found on some LINE6
drivers are currently done in a racy way; namely, the MIDI buffer
instance is allocated and initialized in each private_init callback
while the communication with the interface is already started via
line6_init_cap_control() call before that point. This may lead to
Oops in line6_data_received() when a spurious event is received, as
reported by syzkaller.
This patch moves the MIDI initialization to line6_init_cap_control()
as well instead of the too-lately-called private_init for avoiding the
race. Also this reduces slightly more lines, so it's a win-win
change.
At high sampling transfer frequency, TC Electronic Konnekt Live
transfers/receives 6 audio data frames in multi bit linear audio data
channel of data block in CIP payload. Current hard-coded stream format
is wrong.
Cc: <stable@vger.kernel.org> Fixes: f1f0f330b1d0 ("ALSA: dice: add parameters of stream formats for models produced by TC Electronic") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20210518012612.37268-1-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using smb2_copychunk_range() for large ranges we will
run through several iterations of a loop calling SMB2_ioctl()
but never actually free the returned buffer except for the final
iteration.
This leads to memory leaks everytime a large copychunk is requested.
Fixes: 9bf0c9cd4314 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files") Cc: <stable@vger.kernel.org> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a interruptible mutex locker is interrupted by a signal
without acquiring this lock and removed from the wait queue.
if the mutex isn't contended enough to have a waiter
put into the wait queue again, the setting of the WAITER
bit will force mutex locker to go into the slowpath to
acquire the lock every time, so if the wait queue is empty,
the WAITER bit need to be clear.
Fixes: 040a0a371005 ("mutex: Add support for wound/wait style locks") Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Zqiang <qiang.zhang@windriver.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210517034005.30828-1-qiang.zhang@windriver.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Reset the ns->file value to NULL also in the error case in
nvmet_file_ns_enable().
The ns->file variable points either to file object or contains the
error code after the filp_open() call. This can lead to following
problem:
When the user first setups an invalid file backend and tries to enable
the ns, it will fail. Then the user switches over to a bdev backend
and enables successfully the ns. The first received I/O will crash the
system because the IO backend is chosen based on the ns->file value:
Suppose we have 2 threads, the group-leader L and a sub-theread T,
both parked in ptrace_stop(). Debugger tries to resume both threads
and does
ptrace(PTRACE_CONT, T);
ptrace(PTRACE_CONT, L);
If the sub-thread T execs in between, the 2nd PTRACE_CONT doesn not
resume the old leader L, it resumes the post-exec thread T which was
actually now stopped in PTHREAD_EVENT_EXEC. In this case the
PTHREAD_EVENT_EXEC event is lost, and the tracer can't know that the
tracee changed its pid.
This patch makes ptrace() fail in this case until debugger does wait()
and consumes PTHREAD_EVENT_EXEC which reports old_pid. This affects all
ptrace requests except the "asynchronous" PTRACE_INTERRUPT/KILL.
The patch doesn't add the new PTRACE_ option to not complicate the API,
and I _hope_ this won't cause any noticeable regression:
- If debugger uses PTRACE_O_TRACEEXEC and the thread did an exec
and the tracer does a ptrace request without having consumed
the exec event, it's 100% sure that the thread the ptracer
thinks it is targeting does not exist anymore, or isn't the
same as the one it thinks it is targeting.
- To some degree this patch adds nothing new. In the scenario
above ptrace(L) can fail with -ESRCH if it is called after the
execing sub-thread wakes the leader up and before it "steals"
the leader's pid.
init_dell_smbios_wmi() only registers the dell_smbios_wmi_driver on systems
where the Dell WMI interface is supported. While exit_dell_smbios_wmi()
unregisters it unconditionally, this leads to the following oops:
When there is fatal event on the slave port, the device is marked as not
active. We need to mark it as active again when the slave is recovered to
regain full functionality.
rxe_qp_do_cleanup() relies on valid pointer values in QP for the properly
created ones, but in case rxe_qp_from_init() failed it was filled with
garbage and caused tot the following error.
How the type promotion works in ternary expressions is a bit tricky.
The problem is that scpi_clk_get_val() returns longs, "ret" is a int
which holds a negative error code, and le32_to_cpu() is an unsigned int.
We want the negative error code to be cast to a negative long. But
because le32_to_cpu() is an u32 then "ret" is type promoted to u32 and
becomes a high positive and then it is promoted to long and it is still
a high positive value.
Fix this by getting rid of the ternary.
Link: https://lore.kernel.org/r/YIE7pdqV/h10tEAK@mwanda Fixes: 8cb7cf56c9fe ("firmware: add support for ARM System Control and Power Interface(SCPI) protocol") Reviewed-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[sudeep.holla: changed to return 0 as clock rate on error] Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some distributions are about to switch to Python 3 support only.
This means that /usr/bin/python, which is Python 2, is not available
anymore. Hence, switch scripts to use Python 3 explicitly.
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
When a VCPU is created, the kvm_vcpu struct is initialized to zero in
kvm_vm_ioctl_create_vcpu(). On VHE systems, the first time
vcpu.arch.mdcr_el2 is loaded on hardware is in vcpu_load(), before it is
set to a sensible value in kvm_arm_setup_debug() later in the run loop. The
result is that KVM executes for a short time with MDCR_EL2 set to zero.
This has several unintended consequences:
* Setting MDCR_EL2.HPMN to 0 is constrained unpredictable according to ARM
DDI 0487G.a, page D13-3820. The behavior specified by the architecture
in this case is for the PE to behave as if MDCR_EL2.HPMN is set to a
value less than or equal to PMCR_EL0.N, which means that an unknown
number of counters are now disabled by MDCR_EL2.HPME, which is zero.
* The host configuration for the other debug features controlled by
MDCR_EL2 is temporarily lost. This has been harmless so far, as Linux
doesn't use the other fields, but that might change in the future.
Let's avoid both issues by initializing the VCPU's mdcr_el2 field in
kvm_vcpu_vcpu_first_run_init(), thus making sure that the MDCR_EL2 register
has a consistent value after each vcpu_load().
Fixes: d5a21bcc2995 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions") Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210407144857.199746-3-alexandru.elisei@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bio completions can race when a page spans more than one file system
block. Add a spinlock to synchronize marking the page uptodate.
Fixes: 9dc55f1389f9 ("iomap: add support for sub-pagesize buffered I/O without buffer heads") Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same reasons than for the previous commits : 6289a98f0817 ("sit: proper dev_{hold|put} in ndo_[un]init methods") 40cb881b5aaa ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods") 7f700334be9a ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding dev_hold(),
and vice versa.
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
ip6_gre for example (among others problematic drivers)
has to use dev_hold() in ip6gre_tunnel_init_common()
instead of from ip6gre_newlink_common(), covering
both ip6gre_tunnel_init() and ip6gre_tap_init()/
Note that ip6gre_tunnel_init_common() is not called from
ip6erspan_tap_init() thus we also need to add a dev_hold() there,
as ip6erspan_tunnel_uninit() does call dev_put()
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
In RT system, the spin_lock will be replaced by sleepable rt_mutex lock,
in __call_rcu(), disable interrupts before calling
kasan_record_aux_stack(), will trigger this calltrace:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:951
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 19, name: pgdatinit0
Call Trace:
___might_sleep.cold+0x1b2/0x1f1
rt_spin_lock+0x3b/0xb0
stack_depot_save+0x1b9/0x440
kasan_save_stack+0x32/0x40
kasan_record_aux_stack+0xa5/0xb0
__call_rcu+0x117/0x880
__exit_signal+0xafb/0x1180
release_task+0x1d6/0x480
exit_notify+0x303/0x750
do_exit+0x678/0xcf0
kthread+0x364/0x4f0
ret_from_fork+0x22/0x30
Replace spinlock with raw_spinlock.
Link: https://lkml.kernel.org/r/20210329084009.27013-1-qiang.zhang@windriver.com Signed-off-by: Zqiang <qiang.zhang@windriver.com> Reported-by: Andrew Halaney <ahalaney@redhat.com> Cc: Alexander Potapenko <glider@google.com> Cc: Gustavo A. R. Silva <gustavoars@kernel.org> Cc: Vijayanand Jitta <vjitta@codeaurora.org> Cc: Vinayak Menon <vinmenon@codeaurora.org> Cc: Yogesh Lal <ylal@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
blkdev_read_iter can truncate iov_iter's count since the count + pos may
exceed the size of the blkdev. This will confuse io_read that we have
consume the iovec. And once we do the iov_iter_revert in io_read, we
will trigger the slab-out-of-bounds. Fix it by reexpand the count with
size has been truncated.
Without this change, the DAC ctl's name could be changed only when
the machine has both Speaker and Headphone, but we met some machines
which only has Lineout and Headhpone, and the Lineout and Headphone
share the Audio Mixer0 and DAC0, the ctl's name is set to "Front".
On most of machines, the "Front" is used for Speaker only or Lineout
only, but on this machine it is shared by Lineout and Headphone,
This introduces an issue in the pipewire and pulseaudio, suppose users
want the Headphone to be on and the Speaker/Lineout to be off, they
could turn off the "Front", this works on most of the machines, but on
this machine, the "Front" couldn't be turned off otherwise the
headphone will be off too. Here we do some change to let the ctl's
name change to "Headphone+LO" on this machine, and pipewire and
pulseaudio already could handle "Headphone+LO" and "Speaker+LO".
(https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/747)
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If tcmu_handle_completions() finds an invalid cmd_id while looping over cmd
responses from userspace it sets TCMU_DEV_BIT_BROKEN and breaks the
loop. This means that it does further handling for the tcmu device.
Skip that handling by replacing 'break' with 'return'.
Additionally change tcmu_handle_completions() from unsigned int to bool,
since the value used in return already is bool.
Prior to clang 13.0.0, the RISC-V name for the mcount symbol was
"mcount", which differs from the GCC version of "_mcount", which results
in the following errors:
riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_level':
main.c:(.text+0xe): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_start':
main.c:(.text+0x4e): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `__traceiter_initcall_finish':
main.c:(.text+0x92): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `.LBB32_28':
main.c:(.text+0x30c): undefined reference to `mcount'
riscv64-linux-gnu-ld: init/main.o: in function `free_initmem':
main.c:(.text+0x54c): undefined reference to `mcount'
This has been corrected in https://reviews.llvm.org/D98881 but the
minimum supported clang version is 10.0.1. To avoid build errors and to
gain a working function tracer, adjust the name of the mcount symbol for
older versions of clang in mount.S and recordmcount.pl.
On Qualcomm ARM32 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The ARM32 SMCC code already has the provision to add platform specific
quirks for things like this. So let's make use of it and add the
Qualcomm specific quirk (ARM_SMCCC_QUIRK_QCOM_A6) used by the QCOM_SCM
driver.
This change is similar to the below one added for ARM64 a while ago:
commit 82bcd087029f ("firmware: qcom: scm: Fix interrupted SCM calls")
Without this change, the Qualcomm ARM32 platforms like SDX55 will return
-EINVAL for SMC calls used for modem firmware loading and validation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ritesh reported a bug [1] against UML, noting that it crashed on
startup. The backtrace shows the following (heavily redacted):
(gdb) bt
...
#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268
#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2
#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72
...
#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359
...
#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486
#45 0x00007f8990968b85 in __getgrnam_r [...]
#46 0x00007f89909d6b77 in grantpt [...]
#47 0x00007f8990a9394e in __GI_openpty [...]
#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407
#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598
#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45
#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334
#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144
indicating that the UML function openpty_cb() calls openpty(),
which internally calls __getgrnam_r(), which causes the nsswitch
machinery to get started.
This loads, through lots of indirection that I snipped, the
libcom_err.so.2 library, which (in an unknown function, "??")
calls sem_init().
Now, of course it wants to get libpthread's sem_init(), since
it's linked against libpthread. However, the dynamic linker
looks up that symbol against the binary first, and gets the
kernel's sem_init().
Hajime Tazaki noted that "objcopy -L" can localize a symbol,
so the dynamic linker wouldn't do the lookup this way. I tried,
but for some reason that didn't seem to work.
Doing the same thing in the linker script instead does seem to
work, though I cannot entirely explain - it *also* works if I
just add "VERSION { { global: *; }; }" instead, indicating that
something else is happening that I don't really understand. It
may be that explicitly doing that marks them with some kind of
empty version, and that's different from the default.
Explicitly marking them with a version breaks kallsyms, so that
doesn't seem to be possible.
Marking all the symbols as local seems correct, and does seem
to address the issue, so do that. Also do it for static link,
nsswitch libraries could still be loaded there.
[1] https://bugs.debian.org/983379
Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com Signed-off-by: Feilong Lin <linfeilong@huawei.com> Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enabling function_graph tracer on ARM causes kernel panic, because the
function graph tracer updates the "return address" of a function in order
to insert a trace callback on function exit, it saves the function's
original return address in a return trace stack, but cpu_suspend() may not
return through the normal return path.
cpu_suspend() will resume directly via the cpu_resume path, but the return
trace stack has been set-up by the subfunctions of cpu_suspend(), which
makes the "return address" inconsistent with cpu_suspend().
fixes the issue by pausing/resuming the function graph tracer on the thread
executing cpu_suspend(), so that the function graph tracer state is kept
consistent across functions that enter power down states and never return
by effectively disabling graph tracer while they are executing.
Signed-off-by: louis.wang <liang26812@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
In order to set the correct return flags for poll, the xsk code has to
check if the Rx queue is empty and if the Tx queue is full. This code
was unnecessarily large and complex as it used the functions that are
used to update the local state from the global state (xskq_nb_free and
xskq_nb_avail). Since we are not doing this nor updating any data
dependent on this state, we can simplify the functions. Another
benefit from this is that we can also simplify the xskq_nb_free and
xskq_nb_avail functions in a later commit.
In the second loop of ingenic_pinconf_set(), it annotates the switch
default case as unreachable(). The annotation is technically correct,
because that same case would have resulted in an early function return
in the previous loop.
However, the compiled code is suboptimal. GCC seems to work extra hard
to ensure that the unreachable code path triggers undefined behavior.
The function would fall through to start executing whatever function
happens to be next in the compilation unit.
This is problematic because:
a) it adds unnecessary 'ensure undefined behavior' logic, and
corresponding i-cache footprint; and
b) it's less robust -- if a bug were to be introduced, falling through
to the next function would be catastrophic.
Yet another issue is that, while objtool normally understands
unreachable() annotations, there's one special case where it doesn't:
when the annotation occurs immediately after a 'ret' instruction. That
happens to be the case here because unreachable() is immediately before
the return.
Remove the unreachable() annotation and replace it with a comment. This
simplifies the code generation and changes the unreachable error path to
just silently return instead of corrupting execution.
This fixes the following objtool warning:
drivers/pinctrl/pinctrl-ingenic.o: warning: objtool: ingenic_pinconf_set() falls through to next function ingenic_pinconf_group_set()
gcc-11 complains about a prototype declaration that is different
from the function definition:
drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}
62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}
64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~
Change the definition to make them match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
Do not call nvme_configure_apst when the controller is not live, given
that nvme_configure_apst will fail due the lack of an admin queue when
the controller is being torn down and nvme_set_latency_tolerance is
called from dev_pm_qos_hide_latency_tolerance.
Fixes: 510a405d945b("nvme: fix memory leak for power latency tolerance") Reported-by: Peng Liu <liupeng17@lenovo.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names") Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)
Because their data pointers are not updated to point to per-netns
structures, they must be marked read-only in a non-init_net ns.
Otherwise, changes in any net namespace are reflected in (leaked into)
all other net namespaces. This problem has existed since the
introduction of net namespaces.
The current logic marks them read-only only if the net namespace is
owned by an unprivileged user (other than init_user_ns).
Commit d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in
unprivileged namespaces") "exposes all sysctls even if the namespace is
unpriviliged." Since we need to mark them readonly in any case, we can
forego the unprivileged user check altogether.
Fixes: d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces") Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
The tz->lock must be hold during the looping over the instances in that
thermal zone. This lock was missing in the governor code since the
beginning, so it's hard to point into a particular commit.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210422153624.6074-2-lukasz.luba@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b4c
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.") Reported-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems. It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support. However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.
Make DEFXX_MMIO the configuration default then, except where configured
for EISA. This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core. Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.
The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.
Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e89a2cfb7d7b ("[TC] defxx: TURBOchannel support") Cc: stable@vger.kernel.org # v2.6.21+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201 Reported-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log