This issue was also reported since 2017 in the thread [1],
unfortunately, the issue was still can be reproduced after fixing
DCCP.
The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net
namespace is destroyed since tcp_sk_ops is registered befrore
ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops
in the list of pernet_list. There will be a use-after-free on
net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net
if there are some inflight time-wait timers.
This bug is not introduced by commit f2bf415cfed7 ("mib: add net to
NET_ADD_STATS_BH") since the net_statistics is a global variable
instead of dynamic allocation and freeing. Actually, commit 61a7e26028b9 ("mib: put net statistics on struct net") introduces
the bug since it put net statistics on struct net and free it when
net namespace is destroyed.
Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug
and replace pr_crit() with panic() since continuing is meaningless
when init_ipv4_mibs() fails.
The spaceball.c module was not properly parsing the movement reports
coming from the device. The code read axis data as signed 16-bit
little-endian values starting at offset 2.
In fact, axis data in Spaceball movement reports are signed 16-bit
big-endian values starting at offset 3. This was determined first by
visually inspecting the data packets, and later verified by consulting:
http://spacemice.org/pdf/SpaceBall_2003-3003_Protocol.pdf
If this ever worked properly, it was in the time before Git...
Signed-off-by: Leo L. Schwab <ewhac@ewhac.org> Link: https://lore.kernel.org/r/20211221101630.1146385-1-ewhac@ewhac.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot has reported warning in __flush_work(). This warning is caused by
work->func == NULL, which means missing work initialization.
This may happen, since input_dev->close() calls
cancel_work_sync(&dev->work), but dev->work initalization happens _after_
input_register_device() call.
So this patch moves dev->work initialization before registering input
device
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab439 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/ Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com Fixes: e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length") Cc: Matt Wang <wwentao@vmware.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Vishal Bhakta <vbhakta@vmware.com> Cc: VMware PV-Drivers <pv-drivers@vmware.com> Cc: James E.J. Bottomley <jejb@linux.ibm.com> Cc: linux-scsi@vger.kernel.org Cc: stable@vger.kernel.org Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Alexey Makhalov <amakhalov@vmware.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.13, commit 74310e06be4d ("android: binder: Move buffer out of area shared with user space")
fixed a kernel structure visibility issue. As part of that patch,
sizeof(void *) was used as the buffer size for 0-length data payloads so
the driver could detect abusive clients sending 0-length asynchronous
transactions to a server by enforcing limits on async_free_size.
Unfortunately, on the "free" side, the accounting of async_free_space
did not add the sizeof(void *) back. The result was that up to 8-bytes of
async_free_space were leaked on every async transaction of 8-bytes or
less. These small transactions are uncommon, so this accounting issue
has gone undetected for several years.
The fix is to use "buffer_size" (the allocated buffer size) instead of
"size" (the logical buffer size) when updating the async_free_space
during the free operation. These are the same except for this
corner case of asynchronous transactions with payloads < 8 bytes.
Fixes: 74310e06be4d ("android: binder: Move buffer out of area shared with user space") Signed-off-by: Todd Kjos <tkjos@google.com> Cc: stable@vger.kernel.org # 4.14+ Link: https://lore.kernel.org/r/20211220190150.2107077-1-tkjos@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ffs_data_clear is indirectly called from both ffs_fs_kill_sb and
ffs_ep0_release, so it ends up being called twice when userland closes ep0
and then unmounts f_fs.
If userland provided an eventfd along with function's USB descriptors, it
ends up calling eventfd_ctx_put as many times, causing a refcount
underflow.
NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls.
Also, set epfiles to NULL right after de-allocating it, for readability.
For completeness, ffs_data_clear actually ends up being called thrice, the
last call being before the whole ffs structure gets freed, so when this
specific sequence happens there is a second underflow happening (but not
being reported):
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d82119 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller") Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0fd0 ("NFC: add the NFC socket raw protocol") Fixes: d646960f7986 ("NFC: Initial LLCP support") Cc: <stable@vger.kernel.org> Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com Fixes: 7d5cb45655f2 ("i2c compat ioctls: move to ->compat_ioctl()") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc78 ("fsl/fman: Add FMan Port Support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
udpgso_bench_tx call setup_sockaddr() for dest address before
parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}",
then ${dst_port} will be ignored, and using default cfg_port 8000.
This will cause test case "multiple GRO socks" failed in udpgro.sh.
Setup sockaddr after parsing all arguments.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/ff620d9f-5b52-06ab-5286-44b945453002@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of an error in mlx5e_set_features(), 'netdev->features' must be
updated with the correct state of the device to indicate which features
were updated successfully.
To do that we maintain a copy of 'netdev->features' and update it after
successful feature changes, so we can assign it to back to
'netdev->features' if needed.
However, since not all netdev features are handled by the driver (e.g.
GRO/TSO/etc), some features may not be updated correctly in case of an
error updating another feature.
For example, while requesting to disable TSO (feature which is not
handled by the driver) and enable HW-GRO, if an error occurs during
HW-GRO enable, 'oper_features' will be assigned with 'netdev->features'
and HW-GRO turned off. TSO will remain enabled in such case, which is a
bug.
To solve that, instead of using 'netdev->features' as the baseline of
'oper_features' and changing it on set feature success, use 'features'
instead and update it in case of errors.
Fixes: 75b81ce719b7 ("net/mlx5e: Don't override netdev features field unless in error flow") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Matthias-Christian Ott <ott@mirix.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue occurs when asoc is peeled off and the old sk is freed after
getting it by asoc->base.sk and before calling lock_sock(sk).
To prevent the sk free, as a holder of the sk, ep should be alive when
calling lock_sock(). This patch uses call_rcu() and moves sock_put and
ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to
hold the ep under rcu_read_lock in sctp_transport_traverse_process().
If sctp_endpoint_hold() returns true, it means this ep is still alive
and we have held it and can continue to dump it; If it returns false,
it means this ep is dead and can be freed after rcu_read_unlock, and
we should skip it.
In sctp_sock_dump(), after locking the sk, if this ep is different from
tsp->asoc->ep, it means during this dumping, this asoc was peeled off
before calling lock_sock(), and the sk should be skipped; If this ep is
the same with tsp->asoc->ep, it means no peeloff happens on this asoc,
and due to lock_sock, no peeloff will happen either until release_sock.
Note that delaying endpoint free won't delay the port release, as the
port release happens in sctp_endpoint_destroy() before calling call_rcu().
Also, freeing endpoint by call_rcu() makes it safe to access the sk by
asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv().
Thanks Jones to bring this issue up.
v1->v2:
- improve the changelog.
- add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed.
Reported-by: syzbot+9276d76e83e3bcde6c99@syzkaller.appspotmail.com Reported-by: Lee Jones <lee.jones@linaro.org> Fixes: d25adbeb0cdb ("sctp: fix an use-after-free issue in sctp_sock_dump") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The below referenced commit correctly updated the computation of number
of segments (gso_size) by using only the gso payload size and
removing the header lengths.
With this change the regression test started failing. Update
the tests to match this new behavior.
Both IPv4 and IPv6 tests are updated, as a separate patch in this series
will update udp_v6_send_skb to match this change in udp_send_skb.
Fixes: 158390e45612 ("udp: using datalen to cap max gso segments") Signed-off-by: Coco Li <lixiaoyan@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20211223222441.2975883-2-lixiaoyan@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e45612 ("udp: using datalen to cap max gso segments") Signed-off-by: Coco Li <lixiaoyan@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hooks.c:5765:6: warning: 4th function call argument is an uninitialized
value
if (selinux_xfrm_postroute_last(sksec->sid, skb, &ad, proto))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
selinux_parse_skb() can return ok without setting proto. The later call
to selinux_xfrm_postroute_last() does an early check of proto and can
return ok if the garbage proto value matches. So initialize proto.
Cc: stable@vger.kernel.org Fixes: eef9b41622f2 ("selinux: cleanup selinux_xfrm_sock_rcv_skb() and selinux_xfrm_postroute_last()") Signed-off-by: Tom Rix <trix@redhat.com>
[PM: typo/spelling and checkpatch.pl description fixes] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 85bf17b28f97 ("recordmcount.pl: look for jgnop instruction as well
as bcrl on s390") added a new alternative mnemonic for the existing brcl
instruction. This is required for the combination old gcc version (pre 9.0)
and binutils since version 2.37.
However at the same time this commit introduced a typo, replacing brcl with
bcrl. As a result no mcount locations are detected anymore with old gcc
versions (pre 9.0) and binutils before version 2.37.
Fix this by using the correct mnemonic again.
Reported-by: Miroslav Benes <mbenes@suse.cz> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: <stable@vger.kernel.org> Fixes: 85bf17b28f97 ("recordmcount.pl: look for jgnop instruction as well as bcrl on s390") Link: https://lore.kernel.org/r/alpine.LSU.2.21.2112230949520.19849@pobox.suse.cz Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
Since the tee subsystem does not keep a strong reference to its idle
shared memory buffers, it races with other threads that try to destroy a
shared memory through a close of its dma-buf fd or by unmapping the
memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been
successful, it is possible that the tee_shm is in the dma-buf teardown
path, but that path is blocked by the teedev mutex. Since we don't have
an API to tell if the tee_shm is in the dma-buf teardown path or not we
must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a
new refcount_t refcount field. dma-buf is replaced by using
anon_inode_getfd() instead, this separates the life-cycle of the
underlying file from the tee_shm. tee_shm_put() is updated to hold the
mutex when decreasing the refcount to 0 and then remove the tee_shm from
teedev->idr before releasing the mutex. This means that the tee_shm can
never be found unless it has a refcount larger than 0.
Since commit 4bc43a421218 ("HID: asus: Add
hid_is_using_ll_driver(usb_hid_driver) check") the hid-asus.c depends
on the usb_hid_driver symbol. Add a depends on USB_HID to Kconfig to
fix missing symbols errors in hid-asus when USB_HID is not enabled.
Fixes: 4bc43a421218 ("HID: asus: Add hid_is_using_ll_driver(usb_hid_driver) check") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Jason Self <jason@bluehome.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ioctl() implicitly assumed that the socket was already bound to
a valid local socket name, i.e. Phonet object. If the socket was not
bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being
connected yet not bound to a valid object.
Reported-by: syzbot+2dc91e7fc3dea88b1e8a@syzkaller.appspotmail.com Signed-off-by: Rémi Denis-Courmont <remi@remlab.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit 3e0588c291d6 ("hamradio: defer ax25 kfree after
unregister_netdev") reorder the kfree operations and unregister_netdev
operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of
the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs.
Partial of the stack trace is shown below.
By placing the nullify action after the unregister_netdev, the ax->tty
pointer won't be assigned as NULL net_device framework layer is well
synchronized.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with
routines from mkiss_ioctl. However, it cannot stop the routine coming
from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to
halt the transmit queue but it fails to stop the routine that already
being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the
possible UAF as the unregister_netdev() is well synchronized and won't
return if there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other syscall functions like ax25_getsockopt, ax25_getname,
ax25_info_show also suffer from similar races. To fix them, this patch
introduce lock_sock() into ax25_kill_by_device in order to guarantee
that the nullify action in cleanup routine cannot proceed when another
socket request is pending.
Signed-off-by: Hanjie Wu <nagi@zju.edu.cn> Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33acc ("KVM: VMX: Emulate invalid guest state by default") Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40bee885e ("usb: gadget: u_ether: construct with default values and add setters/getters") Cc: stable@vger.kernel.org Signed-off-by: Marian Postevca <posteuca@mutex.one> Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Overview
page fault in f2fs_setxattr() when mount and operate on corrupted image
- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root
1. unzip tmp7.zip
2. ./single.sh f2fs 7
Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072
F2FS-fs (loop0): Found nat_bits in checkpoint
F2FS-fs (loop0): Mounted with checkpoint version = 7548c2ee
BUG: unable to handle page fault for address: ffffe47bc7123f48
RIP: 0010:kfree+0x66/0x320
Call Trace:
__f2fs_setxattr+0x2aa/0xc00 [f2fs]
f2fs_setxattr+0xfa/0x480 [f2fs]
__f2fs_set_acl+0x19b/0x330 [f2fs]
__vfs_removexattr+0x52/0x70
__vfs_removexattr_locked+0xb1/0x140
vfs_removexattr+0x56/0x100
removexattr+0x57/0x80
path_removexattr+0xa3/0xc0
__x64_sys_removexattr+0x17/0x20
do_syscall_64+0x37/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is in __f2fs_setxattr(), we missed to do sanity check on
last xattr entry, result in out-of-bound memory access during updating
inconsistent xattr data of target inode.
After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry, entry_size: 60676
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry, entry_size: 47736
Cc: stable@vger.kernel.org Reported-by: Wenqing Liu <wenqingliu0120@gmail.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
[delete f2fs_err() call as it's not in older kernels - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org> Fixes: b86040a59feb ("Thumb-2: Implementation of the unified start-up and exceptions code") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider the GPIO controller offset (from "gpio-ranges") to compute the
maximum GPIO line number.
This fixes an issue where gpio-ranges uses a non-null offset.
e.g.: gpio-ranges = <&pinctrl 6 86 10>
In that case the last valid GPIO line is not 9 but 15 (6 + 10 - 1)
Cc: stable@vger.kernel.org Fixes: 67e2996f72c7 ("pinctrl: stm32: fix the reported number of GPIO lines per bank") Reported-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com> Link: https://lore.kernel.org/r/20211215095808.621716-1-fabien.dessenne@foss.st.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The completer in the "or,ev %r1,%r30,%r30" instruction is reversed, so we are
not clipping the LWS number when we are called from a 32-bit process (W=0).
We need to nulify the following depdi instruction when the least-significant
bit of %r30 is 1.
If the %r20 register is not clipped, a user process could perform a LWS call
that would branch to an undefined location in the kernel and potentially crash
the machine.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case, init_srcu_struct fails (because of memory allocation failure), we
might proceed with the driver initialization despite srcu_struct not being
entirely initialized.
Fixes: 913a89f009d9 ("ipmi: Don't initialize anything in the core until something uses it") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Cc: Corey Minyard <cminyard@mvista.com> Cc: stable@vger.kernel.org
Message-Id: <20211217154410.1228673-1-cascardo@canonical.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.
Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20211220140344.978408-1-jiasheng@iscas.ac.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b2292 ("fjes: Introduce FUJITSU Extended Socket Network Device driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key") Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.
Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.
Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).
Skb with skb->protocol 0 at the time of virtio_net_hdr_to_skb may have
a protocol inferred from virtio_net_hdr with virtio_net_hdr_set_proto.
Unlike TCP, UDP does not have separate types for IPv4 and IPv6. Type
VIRTIO_NET_HDR_GSO_UDP is guessed to be IPv4/UDP. As of the below
commit, UFOv6 packets are dropped due to not matching the protocol as
obtained from dev_parse_header_protocol.
Invert the test to take that L2 protocol field as starting point and
pass both UFOv4 and UFOv6 for VIRTIO_NET_HDR_GSO_UDP.
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().
Fixes: 154d0c810c53 ("qlcnic: VLAN enhancement for 84XX adapters") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 5648b5e1169f ("netfilter: nfnetlink_queue: fix OOB when mac
header was cleared"), the test for non-empty MAC header introduced in
commit 2c38de4c1f8da7 ("netfilter: fix looped (broad|multi)cast's MAC
handling") has been replaced with a test for a set MAC header.
This breaks the case when the MAC header has been reset (using
skb_reset_mac_header), as is the case with looped-back multicast
packets. As a result, the packets ending up in NFQUEUE get a bogus
hwaddr interpreted from the first bytes of the IP header.
This patch adds a test for a non-empty MAC header in addition to the
test for a set MAC header. The same two tests are also implemented in
nfnetlink_log.c, where the initial code of commit 2c38de4c1f8da7
("netfilter: fix looped (broad|multi)cast's MAC handling") has not been
touched, but where supposedly the same situation may happen.
Fixes: 5648b5e1169f ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared") Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.
With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.
Fixes: a7affb13b271 ("arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus") Acked-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Ron Goossens <rgoossens@gmail.com> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20211117140222.43692-1-robert.marko@sartura.hr Signed-off-by: Sasha Levin <sashal@kernel.org>
The function bfq_bfqq_expire() invokes the function
__bfq_bfqq_expire(), and the latter may free the in-service bfq-queue.
If this happens, then no other instruction of bfq_bfqq_expire() must
be executed, or a use-after-free will occur.
Basing on the assumption that __bfq_bfqq_expire() invokes
bfq_put_queue() on the in-service bfq-queue exactly once, the queue is
assumed to be freed if its refcounter is equal to one right before
invoking __bfq_bfqq_expire().
But, since commit 9dee8b3b057e ("block, bfq: fix queue removal from
weights tree") this assumption is false. __bfq_bfqq_expire() may also
invoke bfq_weights_tree_remove() and, since commit 9dee8b3b057e
("block, bfq: fix queue removal from weights tree"), also
the latter function may invoke bfq_put_queue(). So __bfq_bfqq_expire()
may invoke bfq_put_queue() twice, and this is the actual case where
the in-service queue may happen to be freed.
To address this issue, this commit moves the check on the refcounter
of the queue right around the last bfq_put_queue() that may be invoked
on the queue.
Fixes: 9dee8b3b057e ("block, bfq: fix queue removal from weights tree") Reported-by: Dmitrii Tcvetkov <demfloro@demfloro.ru> Reported-by: Douglas Anderson <dianders@chromium.org> Tested-by: Dmitrii Tcvetkov <demfloro@demfloro.ru> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bfq maintains an ordered list, through a red-black tree, of unique
weights of active bfq_queues. This list is used to detect whether there
are active queues with differentiated weights. The weight of a queue is
removed from the list when both the following two conditions become
true:
(1) the bfq_queue is flagged as inactive
(2) the has no in-flight request any longer;
Unfortunately, in the rare cases where condition (2) becomes true before
condition (1), the removal fails, because the function to remove the
weight of the queue (bfq_weights_tree_remove) is rightly invoked in the
path that deactivates the bfq_queue, but mistakenly invoked *before* the
function that actually performs the deactivation (bfq_deactivate_bfqq).
This commits moves the invocation of bfq_weights_tree_remove for
condition (1) to after bfq_deactivate_bfqq. As a consequence of this
move, it is necessary to add a further reference to the queue when the
weight of a queue is added, because the queue might otherwise be freed
before bfq_weights_tree_remove is invoked. This commit adds this
reference and makes all related modifications.
Since commit '2d29c9f89fcd ("block, bfq: improve asymmetric scenarios
detection")', if there are process groups with I/O requests waiting for
completion, then BFQ tags the scenario as 'asymmetric'. This detection
is needed for preserving service guarantees (for details, see comments
on the computation * of the variable asymmetric_scenario in the
function bfq_better_to_idle).
Unfortunately, commit '2d29c9f89fcd ("block, bfq: improve asymmetric
scenarios detection")' contains an error exactly in the updating of
the number of groups with I/O requests waiting for completion: if a
group has more than one descendant process, then the above number of
groups, which is renamed from num_active_groups to a more appropriate
num_groups_with_pending_reqs by this commit, may happen to be wrongly
decremented multiple times, namely every time one of the descendant
processes gets all its pending I/O requests completed.
A correct, complete solution should work as follows. Consider a group
that is inactive, i.e., that has no descendant process with pending
I/O inside BFQ queues. Then suppose that num_groups_with_pending_reqs
is still accounting for this group, because the group still has some
descendant process with some I/O request still in
flight. num_groups_with_pending_reqs should be decremented when the
in-flight request of the last descendant process is finally completed
(assuming that nothing else has changed for the group in the meantime,
in terms of composition of the group and active/inactive state of
child groups and processes). To accomplish this, an additional
pending-request counter must be added to entities, and must be
updated correctly.
To avoid this additional field and operations, this commit resorts to
the following tradeoff between simplicity and accuracy: for an
inactive group that is still counted in num_groups_with_pending_reqs,
this commit decrements num_groups_with_pending_reqs when the first
descendant process of the group remains with no request waiting for
completion.
This simplified scheme provides a fix to the unbalanced decrements
introduced by 2d29c9f89fcd. Since this error was also caused by lack
of comments on this non-trivial issue, this commit also adds related
comments.
Since commit 2d29c9f89fcd ("block, bfq: improve asymmetric scenarios
detection"), a scenario is defined asymmetric when one of the
following conditions holds:
- active bfq_queues have different weights
- one or more group of entities (bfq_queue or other groups of entities)
are active
bfq grants fairness and low latency also in such asymmetric scenarios,
by plugging the dispatching of I/O if the bfq_queue in service happens
to be temporarily idle. This plugging may lower throughput, so it is
important to do it only when strictly needed.
By mistake, in commit '2d29c9f89fcd' ("block, bfq: improve asymmetric
scenarios detection") the num_active_groups counter was firstly
incremented and subsequently decremented at any entity (group or
bfq_queue) weight change.
This is useless, because only transitions from active to inactive and
vice versa matter for that counter. Unfortunately this is also
incorrect in the following case: the entity at issue is a bfq_queue
and it is under weight raising. In fact in this case there is a
spurious increment of the num_active_groups counter.
This spurious increment may cause scenarios to be wrongly detected as
asymmetric, thus causing useless plugging and loss of throughput.
This commit fixes this issue by simply removing the above useless and
wrong increments and decrements.
bfq defines as asymmetric a scenario where an active entity, say E
(representing either a single bfq_queue or a group of other entities),
has a higher weight than some other entities. If the entity E does sync
I/O in such a scenario, then bfq plugs the dispatch of the I/O of the
other entities in the following situation: E is in service but
temporarily has no pending I/O request. In fact, without this plugging,
all the times that E stops being temporarily idle, it may find the
internal queues of the storage device already filled with an
out-of-control number of extra requests, from other entities. So E may
have to wait for the service of these extra requests, before finally
having its own requests served. This may easily break service
guarantees, with E getting less than its fair share of the device
throughput. Usually, the end result is that E gets the same fraction of
the throughput as the other entities, instead of getting more, according
to its higher weight.
Yet there are two other more subtle cases where E, even if its weight is
actually equal to or even lower than the weight of any other active
entities, may get less than its fair share of the throughput in case the
above I/O plugging is not performed:
1. other entities issue larger requests than E;
2. other entities contain more active child entities than E (or in
general tend to have more backlog than E).
In the first case, other entities may get more service than E because
they get larger requests, than those of E, served during the temporary
idle periods of E. In the second case, other entities get more service
because, by having many child entities, they have many requests ready
for dispatching while E is temporarily idle.
This commit addresses this issue by extending the definition of
asymmetric scenario: a scenario is asymmetric when
- active entities representing bfq_queues have differentiated weights,
as in the original definition
or (inclusive)
- one or more entities representing groups of entities are active.
This broader definition makes sure that I/O plugging will be performed
in all the above cases, provided that there is at least one active
group. Of course, this definition is very coarse, so it will trigger
I/O plugging also in cases where it is not needed, such as, e.g.,
multiple active entities with just one child each, and all with the same
I/O-request size. The reason for this coarse definition is just that a
finer-grained definition would be rather heavy to compute.
On the opposite end, even this new definition does not trigger I/O
plugging in all cases where there is no active group, and all bfq_queues
have the same weight. So, in these cases some unfairness may occur if
there are asymmetries in I/O-request sizes. We made this choice because
I/O plugging may lower throughput, and probably a user that has not
created any group cares more about throughput than about perfect
fairness. At any rate, as for possible applications that may care about
service guarantees, bfq already guarantees a high responsiveness and a
low latency to soft real-time applications automatically.
In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
In resp_mode_select() sanity check the block descriptor len to avoid UAF.
BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.
Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com Fixes: 8572211842af ("[media] mxl111sf: convert to new DVB USB") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without the bound checks for scpi_pd->name, it could result in the buffer
overflow when copying the SCPI device name from the corresponding device
tree node as the name string is set at maximum size of 30.
Let us fix it by using devm_kasprintf so that the string buffer is
allocated dynamically.
Fixes: 8bec4337ad40 ("firmware: scpi: add device power domain support using genpd") Reported-by: Pedro Batista <pedbap.g@gmail.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org Cc: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20211209120456.696879-1-sudeep.holla@arm.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reported-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in theory multiple unwinders could be compiled in, it does
not make sense in practise. Use a choice to make the unwinder
selection mutually exclusive and mandatory.
Already before this commit it has not been possible to deselect
FRAME_POINTER. Remove the obsolete comment.
Furthermore, to produce a meaningful backtrace with FRAME_POINTER
enabled the kernel needs a specific function prologue:
mov ip, sp
stmfd sp!, {fp, ip, lr, pc}
sub fp, ip, #4
To get to the required prologue gcc uses apcs and no-sched-prolog.
This compiler options are not available on clang, and clang is not
able to generate the required prologue. Make the FRAME_POINTER
config symbol depending on !clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Link: https://github.com/ClangBuiltLinux/linux/issues/1146 Reported-by: Andy Lavr <andy.lavr@gmail.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The naked attribute is known to confuse some old gcc versions when
function arguments aren't explicitly listed as inline assembly operands
despite the gcc documentation. That resulted in commit 9a40ac86152c
("ARM: 6164/1: Add kto and kfrom to input operands list.").
Yet that commit has problems of its own by having assembly operand
constraints completely wrong. If the generated code has been OK since
then, it is due to luck rather than correctness. So this patch also
provides proper assembly operand constraints, and removes two instances
of redundant register usages in the implementation while at it.
Inspection of the generated code with this patch doesn't show any
obvious quality degradation either, so not relying on __naked at all
will make the code less fragile, and avoid some issues with clang.
The only remaining __naked instances (excluding the kprobes test cases)
are exynos_pm_power_up_setup(), tc2_pm_power_up_setup() and
cci_enable_port_for_self(. But in the first two cases, only the function
address is used by the compiler with no chance of inlining it by
mistake, and the third case is called from assembly code only. And the
fact that no stack is available when the corresponding code is executed
does warrant the __naked usage in those cases.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/129 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries") Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-pci@vger.kernel.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Marek Vasut <marex@denx.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.
Fixes: 61fad6816fc1 ("net/packet: tpacket_rcv: avoid a producer race condition") Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1a0 ("netdevsim: bpf: support fake map offload") Suggested-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com> Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed") Signed-off-by: Cyril Novikov <cnovikov@lynx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions) Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
projects / linux-stable / log