n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") Cc: stable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dell DW5829e same as DW5821e except CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
There are 2 types product of DW5829e: normal and eSIM.
So we will add 2 PID for DW5829e.
And for each PID, it support MBIM or RMNET.
Let's see test evidence as below:
BTW, the interface 0x6 of MBIM mode is GNSS port, which not same as NMEA
port. So it's banned from serial option driver.
The remaining interfaces 0x2-0x5 are: MODEM, MODEM, NMEA, DIAG.
Signed-off-by: Slark Xiao <slark_xiao@163.com> Link: https://lore.kernel.org/r/20220214021401.6264-1-slark_xiao@163.com
[ johan: drop unnecessary reservation of interface 1 ] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro brought it to my attention that the dentries may not be filled
when the parse_options() is called, causing the call to set_gid() to
possibly crash. It should only be called if parse_options() succeeds
totally anyway.
He suggested the logical place to do the update is in apply_options().
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
CH341 has Product ID 0x5512 in EPP/MEM mode which is used for
I2C/SPI/GPIO interfaces. In asynchronous serial interface mode
CH341 has PID 0x5523 which is already in the table.
The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.
Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.") Cc: stable@vger.kernel.org Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a trigger is set on an event to disable or enable tracing within an
instance, then tracing should be disabled or enabled in the instance and
not at the top level, which is confusing to users.
Link: https://lkml.kernel.org/r/20220223223837.14f94ec3@rorschach.local.home Cc: stable@vger.kernel.org Fixes: ae63b31e4d0e2 ("tracing: Separate out trace events from global variables") Tested-by: Daniel Bristot de Oliveira <bristot@kernel.org> Reviewed-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 054aa8d439b9 ("fget: check that the fd still exists after getting
a ref to it") fixed a race with getting a reference to a file just as it
was being closed. It was a fairly minimal patch, and I didn't think
re-checking the file pointer lookup would be a measurable overhead,
since it was all right there and cached.
But I was wrong, as pointed out by the kernel test robot.
The 'poll2' case of the will-it-scale.per_thread_ops benchmark regressed
quite noticeably. Admittedly it seems to be a very artificial test:
doing "poll()" system calls on regular files in a very tight loop in
multiple threads.
That means that basically all the time is spent just looking up file
descriptors without ever doing anything useful with them (not that doing
'poll()' on a regular file is useful to begin with). And as a result it
shows the extra "re-check fd" cost as a sore thumb.
Happily, the regression is fixable by just writing the code to loook up
the fd to be better and clearer. There's still a cost to verify the
file pointer, but now it's basically in the noise even for that
benchmark that does nothing else - and the code is more understandable
and has better comments too.
[ Side note: this patch is also a classic case of one that looks very
messy with the default greedy Myers diff - it's much more legible with
either the patience of histogram diff algorithm ]
memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Fixes: 3010f876500f ("mm: discard memblock data later") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older stable branches backporting this commit is complicated as relevant
code changed quite a bit. Furthermore most of the affected hardware barely
works on those and users would want to use the newer kernels anyway.
Cc: stable@vger.kernel.org # 5.4 4.19 and 4.14 Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Lyude Paul <lyude@redhat.com> Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/149 Signed-off-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Remove the flush_workqueue(system_long_wq) call since flushing
system_long_wq is deadlock-prone and since that call is redundant with a
preceding cancel_work_sync()
Link: https://lore.kernel.org/r/20220215210511.28303-3-bvanassche@acm.org Fixes: ef6c49d87c34 ("IB/srp: Eliminate state SRP_TARGET_DEAD") Reported-by: syzbot+831661966588c802aae9@syzkaller.appspotmail.com Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.
One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D
Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex.
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71ad8 ("drm: parse color format support for digital displays") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-by: Matthias Reichl <hias@horus.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a70b ("ipip: add GSO/TSO support") Signed-off-by: Tao Liu <thomas.liu@ucloud.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes: 1593123a6a49 ("tipc: add name table dump to new netlink api") Fixes: 1a1a143daf84 ("tipc: add publication dump to new netlink api") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: Ross Maynard <bids.7405@bigpond.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usually the kernel provides fixup routines to emulate the fldd and fstd
floating-point instructions if they load or store 8-byte from/to a not
natuarally aligned memory location.
On a 32-bit kernel I noticed that those unaligned handlers didn't worked and
instead the application got a SEGV.
While checking the code I found two problems:
First, the OPCODE_FLDD_L and OPCODE_FSTD_L cases were ifdef'ed out by the
CONFIG_PA20 option, and as such those weren't built on a pure 32-bit kernel.
This is now fixed by moving the CONFIG_PA20 #ifdef to prevent the compilation
of OPCODE_LDD_L and OPCODE_FSTD_L only, and handling the fldd and fstd
instructions.
The second problem are two bugs in the 32-bit inline assembly code, where the
wrong registers where used. The calculation of the natural alignment used %2
(vall) instead of %3 (ior), and the first word was stored back to address %1
(valh) instead of %3 (ior).
vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.
vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.
Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.
When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko") Cc: stable@vger.kernel.org Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As previously discussed(https://lkml.org/lkml/2022/1/20/51),
cpuset_attach() is affected with similar cpu hotplug race,
as follow scenario:
cpuset_attach() cpu hotplug
--------------------------- ----------------------
down_write(cpuset_rwsem)
guarantee_online_cpus() // (load cpus_attach)
sched_cpu_deactivate
set_cpu_active()
// will change cpu_active_mask
set_cpus_allowed_ptr(cpus_attach)
__set_cpus_allowed_ptr_locked()
// (if the intersection of cpus_attach and
cpu_active_mask is empty, will return -EINVAL)
up_write(cpuset_rwsem)
To avoid races such as described above, protect cpuset_attach() call
with cpu_hotplug_lock.
Fixes: be367d099270 ("cgroups: let ss->can_attach and ss->attach do whole threadgroups at a time") Cc: stable@vger.kernel.org # v2.6.32+ Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com> Acked-by: Waiman Long <longman@redhat.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dell DW5829e same as DW5821e except the CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
Also, DW5829e includes normal and eSIM type.
Please see below test evidence:
The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.
This is similar to other kernel parameter issues, such as:
Commit 745a600cf1a6 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)
Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.
Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'shell' built-in only returns the first 256 bytes of the command's
output. In some cases, 'shell' is used to return a path; by bumping up
the buffer size to 4096 this lets us capture up to PATH_MAX.
The specific case where I ran into this was due to commit 1e860048c53e
("gcc-plugins: simplify GCC plugin-dev capability test"). After this
change, we now use `$(shell,$(CC) -print-file-name=plugin)` to return
a path; if the gcc path is particularly long, then the path ends up
truncated at the 256 byte mark, which makes the HAVE_GCC_PLUGINS
depends test always fail.
Vivek Thrivikraman reported:
An SCTP server application which is accessed continuously by client
application.
When the session disconnects the client retries to establish a connection.
After restart of SCTP server application the session is not established
because of stale conntrack entry with connection state CLOSED as below.
(removing this entry manually established new connection):
sctp 9 CLOSED src=10.141.189.233 [..] [ASSURED]
Just skip timeout update of closed entries, we don't want them to
stay around forever.
The thead,c900-plic has been used in opensbi to distinguish
PLIC [1]. Although PLICs have the same behaviors in Linux,
they are different hardware with some custom initializing in
firmware(opensbi).
Qute opensbi patch commit-msg by Samuel:
The T-HEAD PLIC implementation requires setting a delegation bit
to allow access from S-mode. Now that the T-HEAD PLIC has its own
compatible string, set this bit automatically from the PLIC driver,
instead of reaching into the PLIC's MMIO space from another driver.
Fix following coccicheck warning:
./arch/arm/mach-omap2/omap_hwmod.c:753:1-23: WARNING: Function
for_each_matching_node should have of_node_put() before break
Early exits from for_each_matching_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't mask off the high nybble when configuring a
RAW perf event.
Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM") Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-2-jmattson@google.com> Reviewed-by: David Dunn <daviddunn@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two methods for signaling the host: the monitor page mechanism
and hypercalls. The monitor page mechanism is used by performance
critical channels (storage, networking, etc.) because it provides
improved throughput. However, latency is increased. Monitor pages are
allocated to these channels.
Monitor pages are not allocated to channels that do not use the monitor
page mechanism. Therefore, these channels do not have a valid monitor id
or valid monitor page data. In these cases, some of the "_show"
functions return incorrect data. They return an invalid monitor id and
data that is beyond the bounds of the hv_monitor_page array fields.
The "channel->offermsg.monitor_allocated" value can be used to determine
whether monitor pages have been allocated to a channel.
Add "is_visible()" callback functions for the device-level and
channel-level attribute groups. These functions will hide the monitor
sysfs files when the monitor mechanism is not used.
Remove ".default_attributes" from "vmbus_chan_attrs" and create a
channel-level attribute group. These changes allow the new
"is_visible()" callback function to be applied to the channel-level
attributes.
Call "sysfs_create_group()" in "vmbus_add_channel_kobj()" to create the
channel's sysfs files. Add a new function,
“vmbus_remove_channel_attr_group()”, and call it in "free_channel()" to
remove the channel's sysfs files when the channel is closed.
Signed-off-by: Kimberly Brown <kimbrownkd@gmail.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
The functions copy_page_to_iter_pipe() and push_pipe() can both
allocate a new pipe_buffer, but the "flags" member initializer is
missing.
Fixes: 241699cd72a8 ("new iov_iter flavour: pipe-backed")
To: Alexander Viro <viro@zeniv.linux.org.uk>
To: linux-fsdevel@vger.kernel.org
To: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Max Kellermann <max.kellermann@ionos.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Do alignment logic properly and use the "ptr" local variable for
calculating the remainder of the alignment.
This became an issue because struct edac_mc_layer has a size that is not
zero modulo eight, and the next offset that was prepared for the private
data was unaligned, causing an alignment exception.
The patch in Fixes: which broke this actually wanted to "what we
actually care about is the alignment of the actual pointer that's about
to be returned." But it didn't check that alignment.
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
The result of the writeback, whether it is an ENOSPC or an EIO, or
anything else, does not inhibit the NFS client from reporting the
correct file timestamps.
Commit ac795161c936 (NFSv4: Handle case where the lookup of a directory
fails) [1], part of Linux since 5.17-rc2, introduced a regression, where
a symbolic link on an NFS mount to a directory on another NFS does not
resolve(?) the first time it is accessed:
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Fixes: ac795161c936 ("NFSv4: Handle case where the lookup of a directory fails") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Tested-by: Donald Buczek <buczek@molgen.mpg.de> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we disable wbt by set WBT_STATE_OFF_DEFAULT in
wbt_disable_default() when switch elevator to bfq. And when
we remove scsi device, wbt will be enabled by wbt_enable_default.
If it become false positive between wbt_wait() and wbt_track()
when submit write request.
The following is the scenario that triggered the problem.
T1 T2 T3
elevator_switch_mq
bfq_init_queue
wbt_disable_default <= Set
rwb->enable_state (OFF)
Submit_bio
blk_mq_make_request
rq_qos_throttle
<= rwb->enable_state (OFF)
scsi_remove_device
sd_remove
del_gendisk
blk_unregister_queue
elv_unregister_queue
wbt_enable_default
<= Set rwb->enable_state (ON)
q_qos_track
<= rwb->enable_state (ON)
^^^^^^ this request will mark WBT_TRACKED without inflight add and will
lead to drop rqw->inflight to -1 in wbt_done() which will trigger IO hung.
Fix this by move wbt_enable_default() from elv_unregister to
bfq_exit_queue(). Only re-enable wbt when bfq exit.
Fixes: 76a8040817b4b ("blk-wbt: make sure throttle is enabled properly")
Remove oneline stale comment, and kill one oneshot local variable.
Signed-off-by: Ming Lei <ming.lei@rehdat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/linux-block/20211214133103.551813-1-qiulaibin@huawei.com/ Signed-off-by: Laibin Qiu <qiulaibin@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 5946d089379a ("ext4: check for overlapping extents in
ext4_valid_extent_entries()"), we can check out the overlapping extent
entry in leaf extent blocks. But the out-of-order extent entry in index
extent blocks could also trigger bad things if the filesystem is
inconsistent. So this patch add a check to figure out the out-of-order
index extents and return error.
Add the 'ifdef CONFIG_PPC64' around the 'ptesync' in function
'emulate_update_regs()' to like it is in 'analyse_instr()'. Since it looks like
it got dropped inadvertently by commit 3cdfcbfd32b9 ("powerpc: Change
analyse_instr so it doesn't modify *regs").
A key detail is that analyse_instr() will never recognise lwsync or
ptesync on 32-bit (because of the existing ifdef), and as a result
emulate_update_regs() should never be called with an op specifying
either of those on 32-bit. So removing them from emulate_update_regs()
should be a nop in terms of runtime behaviour.
Fixes: 3cdfcbfd32b9 ("powerpc: Change analyse_instr so it doesn't modify *regs") Cc: stable@vger.kernel.org # v4.14+ Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[mpe: Add last paragraph of change log mentioning analyse_instr() details] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220211005113.1361436-1-anders.roxell@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.
When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.
By some unknown reason, BIOS on Shenker Dock 15 doesn't set up the
codec mask properly for the onboard audio. Let's set the forced codec
mask to enable the codec discovery.
The forced probe mask via probe_mask 0x100 bit doesn't work any longer
as expected since the bus init code was moved and it's clearing the
codec_mask value that was set beforehand. This patch fixes the
long-time regression by moving the check_probe_mask() call.
GCC 12 correctly reports a potential use-after-free condition in the
xrealloc helper. Fix the warning by avoiding an implicit "free(ptr)"
when size == 0:
In file included from help.c:12:
In function 'xrealloc',
inlined from 'add_cmdname' at help.c:24:2: subcmd-util.h:56:23: error: pointer may be used after 'realloc' [-Werror=use-after-free]
56 | ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:58:31: error: pointer may be used after 'realloc' [-Werror=use-after-free]
58 | ret = realloc(ptr, 1);
| ^~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
syzbot reported that two threads might write over agg_select_timer
at the same time. Make agg_select_timer atomic to fix the races.
BUG: KCSAN: data-race in bond_3ad_initiate_agg_selection / bond_3ad_state_machine_handler
read to 0xffff8881242aea90 of 4 bytes by task 1846 on cpu 1:
bond_3ad_state_machine_handler+0x99/0x2810 drivers/net/bonding/bond_3ad.c:2317
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25910 Comm: syz-executor.1 Tainted: G W 5.17.0-rc4-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()
Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.
BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit
write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
notifier_call_chain kernel/notifier.c:84 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
call_netdevice_notifiers net/core/dev.c:1945 [inline]
unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
ops_exit_list net/core/net_namespace.c:173 [inline]
cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
trace_napi_poll include/trace/events/napi.h:14 [inline]
__napi_poll+0x36b/0x3f0 net/core/dev.c:6366
napi_poll net/core/dev.c:6432 [inline]
net_rx_action+0x29e/0x650 net/core/dev.c:6519
__do_softirq+0x158/0x2de kernel/softirq.c:558
do_softirq+0xb1/0xf0 kernel/softirq.c:459
__local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:394 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0xffff88815883e000 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker
Fixes: 4ea7e38696c7 ("dropmon: add ability to detect when hardware dropsrxpackets") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:
# ip link add dummy0 type dummy
# ip link set dummy0 up
# ip addr add 192.168.111.1/24 dev dummy0
# ping -I dummy0 192.168.111.1 -c1
The issue was also reported on:
https://github.com/iputils/iputils/issues/104
But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.
This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with the symbol_duration in order to get these
values in microseconds.
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303") Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fianelil <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vsock_connect() expects that the socket could already be in the
TCP_ESTABLISHED state when the connecting task wakes up with a signal
pending. If this happens the socket will be in the connected table, and
it is not removed when the socket state is reset. In this situation it's
common for the process to retry connect(), and if the connection is
successful the socket will be added to the connected table a second
time, corrupting the list.
Prevent this by calling vsock_remove_connected() if a signal is received
while waiting for a connection. This is harmless if the socket is not in
the connected table, and if it is in the table then removing it will
prevent list corruption from a double add.
Note for backporting: this patch requires d5afa82c977e ("vsock: correct
removal of socket from the list"), which is in all current stable trees
except 4.9.y.
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
In the function bacct_add_task the code reading task->exit_code was
introduced in commit f3cef7a99469 ("[PATCH] csa: basic accounting over
taskstats"), and it is not entirely clear what the taskstats interface
is trying to return as only returning the exit_code of the first task
in a process doesn't make a lot of sense.
As best as I can figure the intent is to return task->exit_code after
a task exits. The field is returned with per task fields, so the
exit_code of the entire process is not wanted. Only the value of the
first task is returned so this is not a useful way to get the per task
ptrace stop code. The ordinary case of returning this value is
returning after a task exits, which also precludes use for getting
a ptrace value.
It is common to for the first task of a process to also be the last
task of a process so this field may have done something reasonable by
accident in testing.
Make ac_exitcode a reliable per task value by always returning it for
every exited task.
Setting ac_exitcode in a sensible mannter makes it possible to continue
to provide this value going forward.
Similar to commit 94e2238969e8 ("xfrm4: strip ECN bits from tos field"),
clear the ECN bits from iph->tos when setting ->flowi4_tos.
This ensures that the last bit of ->flowi4_tos is cleared, so
ip_route_output_key_hash() isn't going to restrict the scope of the
route lookup.
Use ~INET_ECN_MASK instead of IPTOS_RT_MASK, because we have no reason
to clear the high order bits.
Found by code inspection, compile tested only.
Fixes: 4da3089f2b58 ("[IPSEC]: Use TOS when doing tunnel lookups") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[sudip: manually backport to previous location] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no firmware was present at all (or, presumably, all of the
firmware files failed to parse), we end up unbinding by calling
device_release_driver(), which calls remove(), which then in
iwlwifi calls iwl_drv_stop(), freeing the 'drv' struct. However
the new code I added will still erroneously access it after it
was freed.
Set 'failure=false' in this case to avoid the access, all data
was already freed anyway.
Cc: stable@vger.kernel.org Reported-by: Stefan Agner <stefan@agner.ch> Reported-by: Wolfgang Walter <linux@stwm.de> Reported-by: Jason Self <jason@bluehome.net> Reported-by: Dominik Behr <dominik@dominikbehr.com> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Fixes: ab07506b0454 ("iwlwifi: fix leaks/bad data after failed firmware load") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220208114728.e6b514cf4c85.Iffb575ca2a623d7859b542c33b2a507d01554251@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to finish all async code before the module init sequence is
done. In the reverted commit the PF_USED_ASYNC flag was added to mark a
thread that called async_schedule(). Then the PF_USED_ASYNC flag was
used to determine whether or not async_synchronize_full() needs to be
invoked. This works when modprobe thread is calling async_schedule(),
but it does not work if module dispatches init code to a worker thread
which then calls async_schedule().
For example, PCI driver probing is invoked from a worker thread based on
a node where device is attached:
We end up in a situation where a worker thread gets the PF_USED_ASYNC
flag set instead of the modprobe thread. As a result,
async_synchronize_full() is not invoked and modprobe completes without
waiting for the async code to finish.
The issue was discovered while loading the pm80xx driver:
(scsi_mod.scan=async)
Commit 21c3c5d28007 ("block: don't request module during elevator init")
fixed the deadlock issue which the reverted commit 774a1221e862
("module, async: async_synchronize_full() on module init iff async is
used") tried to fix.
Since commit 0fdff3ec6d87 ("async, kmod: warn on synchronous
request_module() from async workers") synchronous module loading from
async is not allowed.
Given that the original deadlock issue is fixed and it is no longer
allowed to call synchronous request_module() from async we can remove
PF_USED_ASYNC flag to make module init consistently invoke
async_synchronize_full() unless async module probe is requested.
While nvme_rdma_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.
Unlike .queue_rq, in .submit_async_event drivers may not check the ctrl
readiness for AER submission. This may lead to a use-after-free
condition that was observed with nvme-tcp.
The race condition may happen in the following scenario:
1. driver executes its reset_ctrl_work
2. -> nvme_stop_ctrl - flushes ctrl async_event_work
3. ctrl sends AEN which is received by the host, which in turn
schedules AEN handling
4. teardown admin queue (which releases the queue socket)
5. AEN processed, submits another AER, calling the driver to submit
6. driver attempts to send the cmd
==> use-after-free
In order to fix that, add ctrl state check to validate the ctrl
is actually able to accept the AER submission.
This addresses the above race in controller resets because the driver
during teardown should:
1. change ctrl state to RESETTING
2. flush async_event_work (as well as other async work elements)
So after 1,2, any other AER command will find the
ctrl state to be RESETTING and bail out without submitting the AER.
Strangely, dquot_quota_sync ignores the return code from the ->sync_fs
call, which means that quotacalls like Q_SYNC never see the error. This
doesn't seem right, so fix that.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we fail to synchronize the filesystem while preparing to freeze the
fs, abort the freeze.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit 1ade48d0c27d ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.
The NULL pointer dereference bug can be shown as below:
The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.
The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If zram-generator package is installed and works, then we can not remove
zram module because zram swap is being used. This case needs a clean zram
environment, change this test by using hot_add/hot_remove interface. So
even zram device is being used, we still can add zram device and remove
them in cleanup.
The two interface was introduced since kernel commit 6566d1a32bf7("zram:
add dynamic device add/remove functionality") in v4.2-rc1. If kernel
supports these two interface, we use hot_add/hot_remove to slove this
problem, if not, just check whether zram is being used or built in, then
skip it on old kernel.
zram01 uses `free -m` to measure zram memory usage. The results are no
sense because they are polluted by all running processes on the system.
We Should only calculate the free memory delta for the current process.
So use the third field of /sys/block/zram<id>/mm_stat to measure memory
usage instead. The file is available since kernel 4.1.
orig_data_size(first): uncompressed size of data stored in this disk.
compr_data_size(second): compressed size of data stored in this disk
mem_used_total(third): the amount of memory allocated for this disk
Also remove useless zram cleanup call in zram_fill_fs and so we don't
need to cleanup zram twice if fails.
Since commit 43209ea2d17a ("zram: remove max_comp_streams internals"), zram
has switched to per-cpu streams. Even kernel still keep this interface for
some reasons, but writing to max_comp_stream doesn't take any effect. So
skip it on newer kernel ie 4.7.
The code that comparing kernel version is from xfstests testsuite ext4/053.
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. In the Tx case we then leak
the skb structure.
Free the skb structure upon error before returning when appropriate.
As the 'is_tx = 0' cannot be moved in the complete handler because of a
possible race between the delay in switching to STATE_RX_AACK_ON and a
new interrupt, we introduce an intermediate 'was_tx' boolean just for
this purpose.
There is no Fixes tag applying here, many changes have been made on this
area and the issue kind of always existed.
Suggested-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20220125121426.848337-4-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if we get IO error while doing send then we abort without
logging information about which file caused issue. So log it to help
with debugging.
CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Dāvis Mosāns <davispuh@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug is caused by overrunning the sglist and incorrectly testing
sg_dma_len(sglist) before nents. Normally this doesn't cause a crash,
but in this case sglist crossed a page boundary. This occurs in the
following code:
while (sg_dma_len(sglist) && nents--) {
The fix is simply to test nents first and move the decrement of nents
into the loop.
Reported-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:
hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'
when:
CONFIG_GSC=y
CONFIG_SERIO_GSCPS2=y
CONFIG_SERIAL_8250_GSC=y
CONFIG_PCI is not set
and hence PCI_LBA is not set.
IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.
Make the use of iosapic_serial_irq() conditional to fix the build error.
ax88179_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (hdr_off..hdr_off+2*pkt_cnt) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
I have tested that this can be used by a malicious USB device to send a
bogus ICMPv6 Echo Request and receive an ICMPv6 Echo Reply in response
that contains random kernel heap data.
It's probably also possible to get OOB writes from this on a
little-endian system somehow - maybe by triggering skb_cow() via IP
options processing -, but I haven't tested that.
-Wunaligned-access is a new warning in clang that is default enabled for
arm and arm64 under certain circumstances within the clang frontend (see
LLVM commit below). On v5.17-rc2, an ARCH=arm allmodconfig build shows
1284 total/70 unique instances of this warning (most of the instances
are in header files), which is quite noisy.
To keep a normal build green through CONFIG_WERROR, only show this
warning with W=1, which will allow automated build systems to catch new
instances of the warning so that the total number can be driven down to
zero eventually since catching unaligned accesses at compile time would
be generally useful.
There's list corruption on cgrp_cpuctx_list. This happens on the
following path:
perf_cgroup_switch: list_for_each_entry(cgrp_cpuctx_list)
cpu_ctx_sched_in
ctx_sched_in
ctx_pinned_sched_in
merge_sched_in
perf_cgroup_event_disable: remove the event from the list
Use list_for_each_entry_safe() to allow removing an entry during
iteration.
Fixes: 058fe1c0440e ("perf/core: Make cgroup switch visit only cpuctxs with cgroup events") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Rik van Riel <riel@surriel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20220204004057.2961252-1-song@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting the fan speed, i8k_set_fan() calls i8k_get_fan_status(),
causing an unnecessary SMM call since from the two users of this
function, only i8k_ioctl_unlocked() needs to know the new fan status
while dell_smm_write() ignores the new fan status.
Since SMM calls can be very slow while also making error reporting
difficult for dell_smm_write(), remove the function call from
i8k_set_fan() and call it separately in i8k_ioctl_unlocked().
If seccomp tries to kill a process, it should never see that process
again. To enforce this proactively, switch the mode to something
impossible. If encountered: WARN, reject all syscalls, and attempt to
kill the process again even harder.
projects / linux-stable / log