SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
Commit d208b89401e0 ("dm: fix mempool NULL pointer race when
completing IO") didn't go far enough.
When bio_end_io_acct ends the count of in-flight I/Os may reach zero
and the DM device may be suspended. There is a possibility that the
suspend races with dm_stats_account_io.
Fix this by adding percpu "pending_io" counters to track outstanding
dm_io. Move kicking of suspend queue to dm_io_dec_pending(). Also,
rename md_in_flight_bios() to dm_in_flight_bios() and update it to
iterate all pending_io counters.
dm_io_dec_pending() calls end_io_acct() first and will then dec md
in-flight pending count. But if a task is swapping DM table at same
time this can result in a crash due to mempool->elements being NULL:
Fix this by:
1) Establishing pointers to 'struct dm_io' members in
dm_io_dec_pending() so that they may be passed into end_io_acct()
_after_ free_io() is called.
2) Moving end_io_acct() after free_io().
Cc: stable@vger.kernel.org Signed-off-by: Jiazi Li <lijiazi@xiaomi.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[fruggeri: Account for backport conflicts from 35b2c3211609 and 6fc8c827dd4f] Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two processes under CLONE_VM cloning, user process can be corrupted by
seeing zeroed page unexpectedly.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage valid data
swap_slot_free_notify
delete zram entry
swap_readpage zeroed(invalid) data
pte_lock
map the *zero data* to userspace
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return and next refault will
read zeroed data
The swap_slot_free_notify is bogus for CLONE_VM case since it doesn't
increase the refcount of swap slot at copy_mm so it couldn't catch up
whether it's safe or not to discard data from backing device. In the
case, only the lock it could rely on to synchronize swap slot freeing is
page table lock. Thus, this patch gets rid of the swap_slot_free_notify
function. With this patch, CPU A will see correct data.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage original data
pte_lock
map the original data
swap_free
swap_range_free
bd_disk->fops->swap_slot_free_notify
swap_readpage read zeroed data
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return
on next refault will see mapped data by CPU B
The concern of the patch would increase memory consumption since it
could keep wasted memory with compressed form in zram as well as
uncompressed form in address space. However, most of cases of zram uses
no readahead and do_swap_page is followed by swap_free so it will free
the compressed form from in zram quickly.
Link: https://lkml.kernel.org/r/YjTVVxIAsnKAXjTd@google.com Fixes: 0bcac06f27d7 ("mm, swap: skip swapcache for swapin of synchronous device") Reported-by: Ivan Babrou <ivan@cloudflare.com> Tested-by: Ivan Babrou <ivan@cloudflare.com> Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some x86 processors, CPUID leaf 0xA provides information
on Architectural Performance Monitoring features. It
advertises a PMU version which Qemu uses to determine the
availability of additional MSRs to manage the PMCs.
Upon receiving a KVM_GET_SUPPORTED_CPUID ioctl request for
the same, the kernel constructs return values based on the
x86_pmu_capability irrespective of the vendor.
This leaf and the additional MSRs are not supported on AMD
and Hygon processors. If AMD PerfMonV2 is detected, the PMU
version is set to 2 and guest startup breaks because of an
attempt to access a non-existent MSR. Return zeros to avoid
this.
Fixes: a6c06ed1a60a ("KVM: Expose the architectural performance monitoring CPUID leaf") Reported-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Message-Id: <3fef83d9c2b2f7516e8ff50d60851f29a4bcb716.1651058600.git.sandipan.das@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Whenever RCU protected list replaces an object,
the pointer to the new object needs to be updated
_before_ the call to kfree_rcu() or call_rcu()
Because kfree_rcu(ptr, rcu) got support for NULL ptr
only recently in commit 12edff045bc6 ("rcu: Make kfree_rcu()
ignore NULL pointers"), I chose to use the conditional
to make sure stable backports won't miss this detail.
if (psl)
kfree_rcu(psl, rcu);
net/ipv6/mcast.c has similar issues, addressed in a separate patch.
[1]
BUG: KASAN: use-after-free in ip_mc_sf_allow+0x6bb/0x6d0 net/ipv4/igmp.c:2655
Read of size 4 at addr ffff88807d37b904 by task syz-executor.5/908
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
__kasan_record_aux_stack+0x7e/0x90 mm/kasan/generic.c:348
call_rcu+0x99/0x790 kernel/rcu/tree.c:3074
mpls_dev_notify+0x552/0x8a0 net/mpls/af_mpls.c:1656
notifier_call_chain+0xb5/0x200 kernel/notifier.c:84
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1938
call_netdevice_notifiers_extack net/core/dev.c:1976 [inline]
call_netdevice_notifiers net/core/dev.c:1990 [inline]
unregister_netdevice_many+0x92e/0x1890 net/core/dev.c:10751
default_device_exit_batch+0x449/0x590 net/core/dev.c:11245
ops_exit_list+0x125/0x170 net/core/net_namespace.c:167
cleanup_net+0x4ea/0xb00 net/core/net_namespace.c:594
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
The buggy address belongs to the object at ffff88807d37b900
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 4 bytes inside of
64-byte region [ffff88807d37b900, ffff88807d37b940)
Memory state around the buggy address: ffff88807d37b800: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc ffff88807d37b880: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
>ffff88807d37b900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff88807d37b980: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88807d37ba00: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
Fixes: c85bb41e9318 ("igmp: fix ip_mc_sf_allow race [v5]") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Flavio Leitner <fbl@sysclose.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Linux, empty symlinks are invalid, and attempting to create one with
the system call symlink(2) results in an -ENOENT error and this is
explicitly documented in the man page.
If we rename a symlink that was created in the current transaction and its
parent directory was logged before, we actually end up logging the symlink
without logging its content, which is stored in an inline extent. That
means that after a power failure we can end up with an empty symlink,
having no content and an i_size of 0 bytes.
It can be easily reproduced like this:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/testdir
$ sync
# Create a file inside the directory and fsync the directory.
$ touch /mnt/testdir/foo
$ xfs_io -c "fsync" /mnt/testdir
# Create a symlink inside the directory and then rename the symlink.
$ ln -s /mnt/testdir/foo /mnt/testdir/bar
$ mv /mnt/testdir/bar /mnt/testdir/baz
# Now fsync again the directory, this persist the log tree.
$ xfs_io -c "fsync" /mnt/testdir
<power failure>
$ mount /dev/sdc /mnt
$ stat -c %s /mnt/testdir/baz
0
$ readlink /mnt/testdir/baz
$
Fix this by always logging symlinks in full mode (LOG_INODE_ALL), so that
their content is also logged.
A test case for fstests will follow.
CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AlphaProject AP-SH4A-3A/AP-SH4AD-0A SH boards use IRQ0 for their SMSC
LAN911x Ethernet chip, so the networking on them must have been broken by
commit 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure")
which filtered out 0 as well as the negative error codes -- it was kinda
correct at the time, as platform_get_irq() could return 0 on of_irq_get()
failure and on the actual 0 in an IRQ resource. This issue was fixed by
me (back in 2016!), so we should be able to fix this driver to allow IRQ0
usage again...
When merging this to the stable kernels, make sure you also merge commit e330b9a6bb35 ("platform: don't return 0 from platform_get_irq[_byname]()
on error") -- that's my fix to platform_get_irq() for the DT platforms...
In emulated environments, the bridge ports enslaved to br1 get a carrier
before changing br1's PVID. This means that by the time the PVID is
changed, br1 is already operational and configured with an IPv6
link-local address.
When the test is run with netdevs registered by mlxsw, changing the PVID
is vetoed, as changing the VID associated with an existing L3 interface
is forbidden. This restriction is similar to the 8021q driver's
restriction of changing the VID of an existing interface.
Fix this by taking br1 down and bringing it back up when it is fully
configured.
With this fix, the test reliably passes on top of both the SW and HW
data paths (emulated or not).
Fixes: 239e754af854 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/20220502084507.364774-1-idosch@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As pointed out by Sascha Hauer, this patch changes:
if (pmc->config && !pcm->config->prepare_slave_config)
<do nothing>
to:
if (pmc->config && !pcm->config->prepare_slave_config)
snd_dmaengine_pcm_prepare_slave_config()
This breaks the drivers that do not need a call to
dmaengine_slave_config(). Drivers that still need to call
snd_dmaengine_pcm_prepare_slave_config(), but have a NULL
pcm->config->prepare_slave_config should use
snd_dmaengine_pcm_prepare_slave_config() as their prepare_slave_config
callback.
Fixes: 9a1e13440a4f ("ASoC: dmaengine: do not use a NULL prepare_slave_config() callback") Reported-by: Sascha Hauer <sha@pengutronix.de> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220421125403.2180824-1-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com> Fixes: 93cacfd41f82 (hwmon: (adt7470) Allow faster removal) Signed-off-by: Armin Wolf <W_Armin@gmx.de> Tested-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are sleep in atomic bug that could cause kernel panic during
firmware download process. The root cause is that nlmsg_new with
GFP_KERNEL parameter is called in fw_dnld_timeout which is a timer
handler. The call trace is shown below:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
Call Trace:
kmem_cache_alloc_node
__alloc_skb
nfc_genl_fw_download_done
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
...
The nlmsg_new with GFP_KERNEL parameter may sleep during memory
allocation process, and the timer handler is run as the result of
a "software interrupt" that should not call any other function
that could sleep.
This patch changes allocation mode of netlink message from GFP_KERNEL
to GFP_ATOMIC in order to prevent sleep in atomic bug. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device_is_registered() in nfc core is used to check whether
nfc device is registered in netlink related functions such as
nfc_fw_download(), nfc_dev_up() and so on. Although device_is_registered()
is protected by device_lock, there is still a race condition between
device_del() and device_is_registered(). The root cause is that
kobject_del() in device_del() is not protected by device_lock.
The device_is_registered() returns the value of state_in_sysfs and
the state_in_sysfs is set to zero in kobject_del(). If we pass check in
position (1), then set zero in position (2). As a result, the check
in position (1) is useless.
This patch uses bool variable instead of device_is_registered() to judge
whether the nfc device is registered, which is well synchronized.
Fixes: 3e256b8f8dfa ("NFC: add nfc subsystem core") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Cc: stable@vger.kernel.org Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WM8958 DSP controls all return 0 on successful write, not a boolean
value indicating if the write changed the value of the control. Fix this
by returning 1 after a change, there is already a check at the start of
each put() that skips the function in the case that there is no change.
A kernel hang can be observed when running setserial in a loop on a kernel
with force threaded interrupts. The sequence of events is:
setserial
open("/dev/ttyXXX")
request_irq()
do_stuff()
-> serial interrupt
-> wake(irq_thread)
desc->threads_active++;
close()
free_irq()
kthread_stop(irq_thread)
synchronize_irq() <- hangs because desc->threads_active != 0
The thread is created in request_irq() and woken up, but does not get on a
CPU to reach the actual thread function, which would handle the pending
wake-up. kthread_stop() sets the should stop condition which makes the
thread immediately exit, which in turn leaves the stale threads_active
count around.
This problem was introduced with commit 519cc8652b3a, which addressed a
interrupt sharing issue in the PCIe code.
Before that commit free_irq() invoked synchronize_irq(), which waits for
the hard interrupt handler and also for associated threads to complete.
To address the PCIe issue synchronize_irq() was replaced with
__synchronize_hardirq(), which only waits for the hard interrupt handler to
complete, but not for threaded handlers.
This was done under the assumption, that the interrupt thread already
reached the thread function and waits for a wake-up, which is guaranteed to
be handled before acting on the stop condition. The problematic case, that
the thread would not reach the thread function, was obviously overlooked.
Make sure that the interrupt thread is really started and reaches
thread_fn() before returning from __setup_irq().
This utilizes the existing wait queue in the interrupt descriptor. The
wait queue is unused for non-shared interrupts. For shared interrupts the
usage might cause a spurious wake-up of a waiter in synchronize_irq() or the
completion of a threaded handler might cause a spurious wake-up of the
waiter for the ready flag. Both are harmless and have no functional impact.
[ tglx: Amended changelog ]
Fixes: 519cc8652b3a ("genirq: Synchronize only with single thread on free_irq()") Signed-off-by: Thomas Pfaff <tpfaff@pcs.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/552fe7b4-9224-b183-bb87-a8f36d335690@pcs.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.
We must not try to connect the socket while the transport is under
construction, because the mechanisms to safely tear it down are not in
place. As the code stands, we end up leaking the sockets on a connection
error.
Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size"
because it clears "size" bits starting from the "start" bit in the according
bitmap. So it has to use "greater" instead of "greater or equal" when performs
bounds check to make sure that GPIOs are in the available range.
Previous implementation skipped ranges that include the last GPIO in
the range.
I wrote the mail to the maintainers
(https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u)
of the questioned DTSes (because I couldn't understand how the maintainers
interpreted this property), but I haven't received a response.
Since the questioned DTSes use "gpio-reserved-ranges = <0 4>"
(i.e., the beginning of the range), this patch doesn't affect these DTSes at all.
TBH this patch doesn't break any existing DTSes because none of them
reserve gpios at the end of range.
Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property") Signed-off-by: Andrei Lalaev <andrei.lalaev@emlid.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA fireworks driver has a bug in its initial state to return count
shorter than expected by 4 bytes to userspace applications when handling
response frame for Echo Audio Fireworks transaction. It's due to missing
addition of the size for the type of event in ALSA firewire stack.
The Linux tool "lscpu" shows the double amount of CPUs if we have
"model" and "model name" in two different lines in /proc/cpuinfo.
This change combines the model and the model name into one line.
Fix the discrepancy between the two places we check for the CP0 counter
erratum in along with the incorrect comparison of the R4400 revision
number against 0x30 which matches none and consistently consider all
R4000 and R4400 processors affected, as documented in processor errata
publications[1][2][3], following the mapping between CP0 PRId register
values and processor models:
No other revision of either processor has ever been spotted.
Contrary to what has been stated in commit ce202cbb9e0b ("[MIPS] Assume
R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the
CP0 counter as buggy does not preclude it from being used as either a
clock event or a clock source device. It just cannot be used as both at
a time, because in that case clock event interrupts will be occasionally
lost, and the use as a clock event device takes precedence.
Compare against 0x4ff in `can_use_mips_counter' so that a single machine
instruction is produced.
References:
[1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS
Technologies Inc., May 10, 1994, Erratum 53, p.13
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: ce202cbb9e0b ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug") Cc: stable@vger.kernel.org # v2.6.24+ Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's two references floating around here (for the object reference,
not the handle_count reference, that's a different thing):
- The temporary reference held by vgem_gem_create, acquired by
creating the object and released by calling
drm_gem_object_put_unlocked.
- The reference held by the object handle, created by
drm_gem_handle_create. This one generally outlives the function,
except if a 2nd thread races with a GEM_CLOSE ioctl call.
So usually everything is correct, except in that race case, where the
access to gem_object->size could be looking at freed data already.
Which again isn't a real problem (userspace shot its feet off already
with the race, we could return garbage), but maybe someone can exploit
this as an information leak.
Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Hillf Danton <hdanton@sina.com> Reported-by: syzbot+0dc4444774d419e916c8@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Cc: Emil Velikov <emil.velikov@collabora.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Eric Anholt <eric@anholt.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Rob Clark <robdclark@chromium.org> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200202132133.1891846-1-daniel.vetter@ffwll.ch
[OP: backport to 4.19: adjusted DRM_DEBUG() -> DRM_DEBUG_DRIVER()] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.
Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result. Same is true for the forward chain, so restrict the use
to prerouting, input and output.
Use in output work if a socket is already attached to the skb.
Fixes: 554ced0a6e29 ("netfilter: nf_tables: add support for native socket matching") Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
When resuming from system sleep state, restore_processor_state()
restores the boot CPU MSRs. These MSRs could be emulated by microcode.
If microcode is not loaded yet, writing to emulated MSRs leads to
unchecked MSR access error:
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
because the copychunk_write might cover a region of the file that has not yet
been sent to the server and thus fail.
A simple way to reproduce this is:
truncate -s 0 /mnt/testfile; strace -f -o x -ttT xfs_io -i -f -c 'pwrite 0k 128k' -c 'fcollapse 16k 24k' /mnt/testfile
the issue is that the 'pwrite 0k 128k' becomes rearranged on the wire with
the 'fcollapse 16k 24k' due to write-back caching.
fcollapse is implemented in cifs.ko as a SMB2 IOCTL(COPYCHUNK_WRITE) call
and it will fail serverside since the file is still 0b in size serverside
until the writes have been destaged.
To avoid this we must ensure that we destage any unwritten data to the
server before calling COPYCHUNK_WRITE.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1997373 Reported-by: Xiaoli Feng <xifeng@redhat.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment. However,
this condition may misbehave if "size" is greater than 4GiB.
The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one. However, the
cast truncates high bits in "size" and it results in misbehavior.
For example:
suppose that size == 0x100000001, dest == 0x200000002
min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
...
dest += 0x1;
so we copy just one byte "and" dest remains unaligned.
This patch fixes the bug by replacing unsigned with size_t.
Do not update tunnel->tun_hlen in data plane code. Use a local variable
instead, just like "tunnel_hlen" in net/ipv4/ip_gre.c:gre_fb_xmit().
Co-developed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.
EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org>
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
A null pointer reference issue can be triggered when the response of a
stream reconf request arrives after the timer is triggered, such as:
send Incoming SSN Reset Request --->
CPU0:
reconf timer is triggered,
go to the handler code before hold sk lock
<--- reply with Outgoing SSN Reset Request
CPU1:
process Outgoing SSN Reset Request,
and set asoc->strreset_chunk to NULL
CPU0:
continue the handler code, hold sk lock,
and try to hold asoc->strreset_chunk, crash!
In tcp_create_openreq_child we adjust tcp_header_len for md5 using the
remote address in newsk. But that address is still 0 in newsk at this
point, and it is only set later by the callers (tcp_v[46]_syn_recv_sock).
Use the address from the request socket instead.
Fixes: cfb6eeb4c860 ("[TCP]: MD5 Signature Option (RFC2385) support.") Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220421005026.686A45EC01F2@us226.sjc.aristanetworks.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff7103 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
introduces general mmc aliases. Let's tailor them to the need
of the GTA04 board which does not make use of mmc2 and mmc3 interfaces.
Fixes: a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <dc9173ee3d391d9e92b7ab8ed4f84b29f0a21c83.1646744420.git.hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c07861491 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae5a ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose") Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of 3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable <stable@kernel.org> Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend") Cc: stable@vger.kernel.org # v4.0+ Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da92f
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is off") Cc: stable@vger.kernel.org # 4.17 Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.
[80802.185460][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682] __memcpy+0x12c/0x180
[80802.263155][ T8682] uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682] process_one_work+0x2cc/0x568
[80802.263173][ T8682] worker_thread+0x28c/0x518
[80802.263181][ T8682] kthread+0x160/0x170
[80802.263188][ T8682] ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829a88130cb a8c130
Fixes: d692522577c0 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
The result is technically harmless, as both the source and the
destinations are currently the same allocation size (4 bytes) and don't
use their padding, but if anything were to ever be added after the
"mcr" member in "struct whiteheat_private", it would be overwritten. The
structs both have a single u8 "mcr" member, but are 4 bytes in padded
size. The memcpy() destination was explicitly targeting the u8 member
(size 1) with the length of the whole structure (size 4), triggering
the memcpy buffer overflow warning:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/spinlock.h:62,
from include/linux/mmzone.h:8,
from include/linux/gfp.h:6,
from include/linux/slab.h:15,
from drivers/usb/serial/whiteheat.c:17:
In function 'fortify_memcpy_chk',
inlined from 'firm_send_command' at drivers/usb/serial/whiteheat.c:587:4:
include/linux/fortify-string.h:328:25: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
328 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
In commit 9ea9b9c48387 ("remove the lightnvm subsystem") the lightnvm
subsystem was removed as there is no hardware in the wild for it, and
the code is known to have problems. This should also be disabled for
older LTS kernels as well to prevent anyone from accidentally using it.
Cc: Christoph Hellwig <hch@lst.de> Cc: Matias Bjørling <mb@lightnvm.io> Cc: Javier González <javier@javigon.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this commit is a part of generic kretprobe trampoline
handler series, without the other patches in that series, this
causes a build error on ia64.
The commit f5f96e3643dc ("ia64: kprobes: Fix to pass correct trampoline
address to the handler") was wrongly backported. It involves another
commit which is a part of another bigger series, so it should not be
backported to the stable tree.
Michael Ellerman [Thu, 28 Apr 2022 12:41:50 +0000 (22:41 +1000)]
powerpc/64s: Unmerge EX_LR and EX_DAR
The SLB miss handler is not fully re-entrant, it is able to work because
we ensure that the SLB entries for the kernel text and data segment, as
well as the kernel stack are pinned in the SLB. Accesses to kernel data
outside of those areas has to be carefully managed and can only occur in
certain parts of the code. One way we deal with that is by storing some
values in temporary slots in the paca.
In v4.13 in commit dbeea1d6b4bd ("powerpc/64s/paca: EX_LR can be merged
with EX_DAR") we merged the storage for two temporary slots for register
storage during SLB miss handling. That was safe at the time because the
two slots were never used at the same time.
Unfortunately in v4.17 in commit c2b4d8b7417a ("powerpc/mm/hash64:
Increase the VA range") we broke that condition, and introduced a case
where the two slots could be in use at the same time, leading to one
being corrupted.
Specifically in slb_miss_common() when we detect that we're handling a
fault for a large virtual address (> 512TB) we go to the "8" label,
there we store the original fault address into paca->exslb[EX_DAR],
before jumping to large_addr_slb() (using rfid).
We then use the EXCEPTION_PROLOG_COMMON and RECONCILE_IRQ_STATE macros
to do exception setup, before reloading the fault address from
paca->exslb[EX_DAR] and storing it into pt_regs->dar (Data Address
Register).
However the code generated by those macros can cause a recursive SLB
miss on a kernel address in three places.
Firstly is the saving of the PPR (Program Priority Register), which
happens on all CPUs since Power7, the PPR is saved to the thread struct
which can be anywhere in memory. There is also the call to
accumulate_stolen_time() if CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y and
CONFIG_PPC_SPLPAR=y, and also the call to trace_hardirqs_off() if
CONFIG_TRACE_IRQFLAGS=y. The latter two call into generic C code and can
lead to accesses anywhere in memory.
On modern 64-bit CPUs we have 1TB segments, so for any of those accesses
to cause an SLB fault they must access memory more than 1TB away from
the kernel text, data and kernel stack. That typically only happens on
machines with more than 1TB of RAM. However it is possible on multi-node
Power9 systems, because memory on the 2nd node begins at 32TB in the
linear mapping.
If we take a recursive SLB fault then we will corrupt the original fault
address with the LR (Link Register) value, because the EX_DAR and EX_LR
slots share storage. Subsequently we will think we're trying to fault
that LR address, which is the wrong address, and will also mostly likely
lead to a segfault because the LR address will be < 512TB and so will be
rejected by slb_miss_large_addr().
This appears as a spurious segfault to userspace, and if
show_unhandled_signals is enabled you will see a fault reported in dmesg
with the LR address, not the expected fault address, eg:
Notice that the fault address == the LR, and the faulting instruction is
a simple store that should never use LR.
In upstream this was fixed in v4.20 in commit 48e7b7695745 ("powerpc/64s/hash: Convert SLB miss handlers to C"),
however that is a huge rewrite and not backportable.
The minimal fix for stable is to just unmerge the EX_LR and EX_DAR slots
again, avoiding the corruption of the DAR value. This uses an extra 8
bytes per CPU, which is negligble.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Piggin [Thu, 28 Apr 2022 12:41:49 +0000 (22:41 +1000)]
powerpc/64/interrupt: Temporarily save PPR on stack to fix register corruption due to SLB miss
This is a minimal stable kernel fix for the problem solved by 4c2de74cc869 ("powerpc/64: Interrupts save PPR on stack rather than
thread_struct").
Upstream kernels between 4.17-4.20 have this bug, so I propose this
patch for 4.19 stable.
Longer description from mpe:
In commit f384796c4 ("powerpc/mm: Add support for handling > 512TB
address in SLB miss") we added support for using multiple context ids
per process. Previously accessing past the first context id was a fatal
error for the process. With the new support it became non-fatal, and so
the previous "bad_addr_slb" handler was changed to be the
"large_addr_slb" handler.
That handler uses the EXCEPTION_PROLOG_COMMON() macro, which in-turn
calls the SAVE_PPR() macro. At the point where SAVE_PPR() is used, the
r9-13 register values from the original user fault are saved in
paca->exslb. It's not until later in EXCEPTION_PROLOG_COMMON_2() that
they are saved from paca->exslb onto the kernel stack.
The PPR is saved into current->thread.ppr, which is notably not on the
kernel stack the way pt_regs are. This means we can take an SLB miss on
current->thread.ppr. If that happens in the "large_addr_slb" case we
will clobber the saved user r9-r13 in paca->exslb with kernel values.
Later we will save those clobbered values into the pt_regs on the stack,
and when we return to userspace those kernel values will be restored.
Typically this appears as some sort of segfault in userspace, with an
address that looks like a kernel address. In dmesg it can appear as:
The upstream fix for this issue was to move PPR into pt_regs, on the
kernel stack, avoiding the possibility of an SLB fault when saving it.
However changing the size of pt_regs is an intrusive change, and has
side effects in other parts of the kernel. A minimal fix is to
temporarily save the PPR in an unused part of pt_regs, then save the
user register values from paca->exslb into pt_regs, and then move the
saved PPR into thread.ppr.
Fixes: f384796c40dc ("powerpc/mm: Add support for handling > 512TB address in SLB miss") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220316033235.903657-1-npiggin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are now able to detect extra put_net() at the moment
they happen, instead of much later in correct code paths.
u32_init_knode() / tcf_exts_init() populates the ->exts.net
pointer, but as mentioned in tcf_exts_init(),
the refcount on netns has not been elevated yet.
The refcount is taken only once tcf_exts_get_net()
is called.
So the two u32_destroy_key() calls from u32_change()
are attempting to release an invalid reference on the netns.
The former patch "defer 6pack kfree after unregister_netdev" reorders
the kfree of two buffer after the unregister_netdev to prevent the race
condition. It also adds free_netdev() function in sixpack_close(), which
is a direct copy from the similar code in mkiss_close().
However, in sixpack driver, the flag needs_free_netdev is set to true in
sp_setup(), hence the unregister_netdev() will free the netdev
automatically. Therefore, as the sp is netdev_priv, use-after-free
occurs.
This patch removes the needs_free_netdev = true and just let the
free_netdev to finish this deallocation task.
Fixes: 0b9111922b1f ("hamradio: defer 6pack kfree after unregister_netdev") Signed-off-by: Lin Ma <linma@zju.edu.cn> Link: https://lore.kernel.org/r/20211111141402.7551-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the patch "defer ax25 kfree after unregister_netdev", this
patch reorder the kfree after the unregister_netdev to avoid the possible
UAF as the unregister_netdev() is well synchronized and won't return if
there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log