Our futex implementation makes use of LDXR/STXR loops to perform atomic
updates to user memory from atomic context. This can lead to latency
problems if we end up spinning around the LL/SC sequence at the expense
of doing something useful.
Rework our futex atomic operations so that we return -EAGAIN if we fail
to update the futex word after 128 attempts. The core futex code will
reschedule if necessary and we'll try again later.
Some futex() operations, including FUTEX_WAKE_OP, require the kernel to
perform an atomic read-modify-write of the futex word via the userspace
mapping. These operations are implemented by each architecture in
arch_futex_atomic_op_inuser() and futex_atomic_cmpxchg_inatomic(), which
are called in atomic context with the relevant hash bucket locks held.
Although these routines may return -EFAULT in response to a page fault
generated when accessing userspace, they are expected to succeed (i.e.
return 0) in all other cases. This poses a problem for architectures
that do not provide bounded forward progress guarantees or fairness of
contended atomic operations and can lead to starvation in some cases.
In these problematic scenarios, we must return back to the core futex
code so that we can drop the hash bucket locks and reschedule if
necessary, much like we do in the case of a page fault.
Allow architectures to return -EAGAIN from their implementations of
arch_futex_atomic_op_inuser() and futex_atomic_cmpxchg_inatomic(), which
will cause the core futex code to reschedule if necessary and return
back to the architecture code later on.
Cc: <stable@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in sst_dsp_new() if we get an error return from sst_dma_new()
we just print an error message and then still complete the function
successfully. This means that we are trying to run without sst->dma
properly set up, which will result in NULL pointer dereference when
sst->dma is later used. This was happening for me in
sst_dsp_dma_get_channel():
We are not as likely to be vulnerable as storage, as it is unlikelier
that UAS is run over a controller without native support for SG,
but the issue exists.
The issue has been existing since the inception of the driver.
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Struct ca is copied from userspace. It is not checked whether the "name"
field is NULL terminated, which allows local users to obtain potentially
sensitive information from kernel stack memory, via a HIDPCONNADD command.
This patch fixes issue reported by some of the customers, who discovered
that after cable pull scenario the devices disappear and path seems to
remain in blocked state. Once the device reappears, driver does not seem to
update path to online. This issue appears because of the defer flag
creating race condition where the same session reappears. This patch fixes
this issue by indicating SCSI-ML of device lost when
qlt_free_session_done() is called from qlt_unreg_sess().
Fixes: 41dc529a4602a ("qla2xxx: Improve RSCN handling in driver") Signed-off-by: Quinn Tran <qtran@marvell.com> Cc: stable@vger.kernel.org #4.19 Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e6f77540c067 ("scsi: qla2xxx: Fix an integer overflow in sysfs
code") incorrectly set 'optrom_region_size' to 'start+size', which can
overflow option-rom boundaries when 'start' is non-zero. Continue setting
optrom_region_size to the proper adjusted value of 'size'.
Fixes: e6f77540c067 ("scsi: qla2xxx: Fix an integer overflow in sysfs code") Cc: stable@vger.kernel.org Signed-off-by: Andrew Vasquez <andrewv@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: James Smart <james.smart@broadcom.com> Cc: Dick Kennedy <dick.kennedy@broadcom.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Kees Cook <keescook@chromium.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enabling ARCH_SUNXI from allnoconfig, SUNXI_SRAM is enabled, but
not REGMAP_MMIO, so the kernel fails to link with an undefined reference
to __devm_regmap_init_mmio_clk. Select REGMAP_MMIO, as suggested in
drivers/base/regmap/Kconfig.
This creates the following dependency loop:
drivers/of/Kconfig:68: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:63: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by SUNXI_SRAM
drivers/soc/sunxi/Kconfig:4: symbol SUNXI_SRAM is selected by USB_MUSB_SUNXI
drivers/usb/musb/Kconfig:63: symbol USB_MUSB_SUNXI depends on GENERIC_PHY
drivers/phy/Kconfig:7: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:29: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:12: symbol MDIO_BUS default is visible depending on PHYLIB
drivers/net/phy/Kconfig:181: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:18: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:24: symbol ARC_EMAC depends on OF_IRQ
To fix the circular dependency, make USB_MUSB_SUNXI select GENERIC_PHY
instead of depending on it. This matches the use of GENERIC_PHY by all
but two other drivers.
Cc: <stable@vger.kernel.org> # 4.19 Fixes: 5828729bebbb ("soc: sunxi: export a regmap for EMAC clock reg on A64") Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The frequency calculation was based on the current(max) frequency of the
CPU. However for low frequency, the value used was already the parent
frequency divided by a factor of 2.
Instead of using this frequency, this fix directly get the frequency from
the parent clock.
Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Cc: <stable@vger.kernel.org> Reported-by: Christian Neubert <christian.neubert.86@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.
So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512. However, USB 3 has a bulk maxpacket
size of 1024. Since the xhci-hcd driver includes native SG support,
this hasn't mattered much. But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.
The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers. The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.
Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Seth Bollinger <Seth.Bollinger@digi.com> Tested-by: Seth Bollinger <Seth.Bollinger@digi.com> CC: Ming Lei <tom.leiming@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Also note that the first race was fixed by 36e59e0d70d6 ("cdc-acm: fix
race between callback and unthrottle") back in 2015, but the bug was
reintroduced a year later.
When irq_set_affinity_notifier() replaces the notifier, then the
reference count on the old notifier is dropped which causes it to be
freed. But nothing ensures that the old notifier is not longer queued
in the work list. If it is queued this results in a use after free and
possibly in work list corruption.
Ensure that the work is canceled before the reference is dropped.
The exlcusion range limit register needs to contain the
base-address of the last page that is part of the range, as
bits 0-11 of this register are treated as 0xfff by the
hardware for comparisons.
So correctly set the exclusion range in the hardware to the
last page which is _in_ the range.
irq_work_run()
perf_pending_event()
if (@pending_disable)
perf_event_disable_local(); // WHOOPS
The problem exists in generic, but s390 is particularly sensitive
because it doesn't implement arch_irq_work_raise(), nor does it call
irq_work_run() from it's PMU interrupt handler (nor would that be
sufficient in this case, because s390 also generates
perf_event_overflow() from pmu::stop). Add to that the fact that s390
is a virtual architecture and (virtual) CPU-A can stall long enough
for the above race to happen, even if it would self-IPI.
Adding a irq_work_sync() to event_sched_in() would work for all hardare
PMUs that properly use irq_work_run() but fails for software PMUs.
Instead encode the CPU number in @pending_disable, such that we can
tell which CPU requested the disable. This then allows us to detect
the above scenario and even redirect the IPI to make up for the failed
queue.
Reported-by: Thomas-Mich Richter <tmricht@linux.ibm.com> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's used by probe and that isn't an init function. Drop this so that we
don't get a section mismatch.
Reported-by: kbuild test robot <lkp@intel.com> Cc: David Müller <dave.mueller@gmx.ch> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Fixes: 7c2e07130090 ("clk: x86: Add system specific quirk to mark clocks as critical") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a long-standing bug that initialized the FC-NVME
cmnd iu CSN value to 1. Early FC-NVME specs had the connection starting
with CSN=1. By the time the spec reached approval, the language had
changed to state a connection should start with CSN=0. This patch
corrects the initialization value for FC-NVME connections.
Additionally, in reviewing the transport, the CSN value is assigned to
the new IU early in the start routine. It's possible that a later dma
map request may fail, causing the command to never be sent to the
controller. Change the location of the assignment so that it is
immediately prior to calling the lldd. Add a comment block to explain
the impacts if the lldd were to additionally fail sending the command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-blk, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num-queues' specified
by qemu is more than maxcpus, virtio-blk would not be able to allocate more
than maxcpus vectors in order to have a vector for each queue. As a result,
it falls back into MSI-X with one vector for config and one shared for
queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-blk by nr_cpu_ids.
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/mediatek/mtk_hdmi.c:1521:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
drivers/gpu/drm/mediatek/mtk_hdmi.c:1524:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: CK Hu <ck.hu@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mediatek@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to the incorrect use of the seg and obj information, the position of
the mtt is calculated incorrectly, and the free space of the page is not
enough to store the entire mtt, resulting in access to the next page. This
patch fixes this problem.
Unable to handle kernel paging request at virtual address ffff00006e3cd000
...
Call trace:
hns_roce_write_mtt+0x154/0x2f0 [hns_roce]
hns_roce_buf_write_mtt+0xa8/0xd8 [hns_roce]
hns_roce_create_srq+0x74c/0x808 [hns_roce]
ib_create_srq+0x28/0xc8
Fixes: 0203b14c4f32 ("RDMA/hns: Unify the calculation for hem index in hip08") Signed-off-by: chenglang <chenglang@huawei.com> Signed-off-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. Not all clk_data->hws[] need to be initialized, depending on various
configured quirks. This leads to NULL ptr deref in
clk_hw_unregister_gate() in sun8i_tcon_top_unbind()
2. If there is error when registering the clk_data->hws[],
err_unregister_gates error path will try to unregister
IS_ERR()=true (invalid) pointer.
The commit 510ded33e075 ("slab: implement slab_root_caches list")
changes the name of the list node within "struct kmem_cache" from "list"
to "root_caches_node", but leaks_show() still use the "list" which
causes a crash when reading /proc/slab_allocators.
You need to have CONFIG_SLAB=y and CONFIG_MEMCG=y to see the problem,
because without MEMCG all slab caches are root caches, and the "list"
node happens to be the right one.
The chips main power supplies VA and VP are enabled during probe but
then never disabled, this will cause warnings from the regulator
framework on driver removal. Fix this by adding a remove callback and
disabling the supplies, whilst doing so follow best practice and put the
chip back into reset as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
the member sdr_white_level of struct dc_cursor_attributes was not
initialized, then the random value result that
dcn10_set_cursor_sdr_white_level() set error hw_scale value 0x20D9(normal
value is 0x3c00), this cause the black cursor issue.
[how]
just initilize the obj of struct dc_cursor_attributes to zero to avoid
the random value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Tianci Yin <tianci.yin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use parentheses around uses of the argument in u64_to_user_ptr() to
ensure that the cast doesn't apply to part of the argument.
There are existing uses of the macro of the form
u64_to_user_ptr(A + B)
which expands to
(void __user *)(uintptr_t)A + B
(the cast applies to the first operand of the addition, the addition
is a pointer addition). This happens to still work as intended, the
semantic difference doesn't cause a difference in behavior.
But I want to use u64_to_user_ptr() with a ternary operator in the
argument, like so:
Stephane reported that the TFA MSR is not initialized by the kernel,
but the TFA bit could set by firmware or as a leftover from a kexec,
which makes the state inconsistent.
Reported-by: Stephane Eranian <eranian@google.com> Tested-by: Nelson DSouza <nelson.dsouza@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: tonyj@suse.com Link: https://lkml.kernel.org/r/20190321123849.GN6521@hirez.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an event is programmed with attr.wakeup_events=N (N>0), it means
the caller is interested in getting a user level notification after
N samples have been recorded in the kernel sampling buffer.
With precise events on Intel processors, the kernel uses PEBS.
The kernel tries minimize sampling overhead by verifying
if the event configuration is compatible with multi-entry PEBS mode.
If so, the kernel is notified only when the buffer has reached its threshold.
Other PEBS operates in single-entry mode, the kenrel is notified for each
PEBS sample.
The problem is that the current implementation look at frequency
mode and event sample_type but ignores the wakeup_events field. Thus,
it may not be possible to receive a notification after each precise event.
This patch fixes this problem by disabling multi-entry PEBS if wakeup_events
is non-zero.
Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: kan.liang@intel.com Link: https://lkml.kernel.org/r/20190306195048.189514-1-eranian@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KGDB_call_nmi_hook is called by other cpu through smp call.
MIPS smp call is processed in ipi irq handler and regs is saved in
handle_int.
So kgdb_call_nmi_hook get regs by get_irq_regs and regs will be passed
to kgdb_cpu_enter.
Signed-off-by: Chong Qiao <qiaochong@loongson.cn> Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: QiaoChong <qiaochong@loongson.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>
The receive side mapping (RSM) on hfi1 hardware is a special
matching mechanism to direct an incoming packet to a given
hardware receive context. It has 4 instances of matching capabilities
(RSM0 - RSM3) that share the same RSM table (RMT). The RMT has a total of
256 entries, each of which points to a receive context.
Currently, three instances of RSM have been used:
1. RSM0 by QOS;
2. RSM1 by PSM FECN;
3. RSM2 by VNIC.
Each RSM instance should reserve enough entries in RMT to function
properly. Since both PSM and VNIC could allocate any receive context
between dd->first_dyn_alloc_ctxt and dd->num_rcv_contexts, PSM FECN must
reserve enough RMT entries to cover the entire receive context index
range (dd->num_rcv_contexts - dd->first_dyn_alloc_ctxt) instead of only
the user receive contexts allocated for PSM
(dd->num_user_contexts). Consequently, the sizing of
dd->num_user_contexts in set_up_context_variables is incorrect.
Fixes: 2280740f01ae ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an old ack_queue entry is used to store an incoming request, it may
need to clean up the old entry if it is still referencing the
MR. Originally only RDMA READ request needed to reference MR on the
responder side and therefore the opcode was tested when cleaning up the
old entry. The introduction of tid rdma specific operations in the
ack_queue makes the specific opcode tests wrong. Multiple opcodes (RDMA
READ, TID RDMA READ, and TID RDMA WRITE) may need MR ref cleanup.
Remove the opcode specific tests associated with the ack_queue.
Fixes: f48ad614c100 ("IB/hfi1: Move driver out of staging") Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_OMAP4_DSS_HDMI_CEC is enabled in .config, deeper SoC idle
states are blocked because the CEC clock gets always enabled on init.
Let's fix the issue by moving the CEC clock handling to happen later in
hdmi_cec_adap_enable() as suggested by Hans Verkuil <hverkuil@xs4all.nl>.
This way the CEC clock gets only enabled when needed. This can be tested
by doing cec-ctl --playback to enable the CEC, and doing cec-ctl --clear
to disable it.
Let's also fix the typo for "divider" in the comments while at it.
Fixes: 8d7f934df8d8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support") Suggested-by: Hans Verkuil <hverkuil@xs4all.nl> Cc: Hans Verkuil <hverkuil@xs4all.nl> Cc: Jyri Sarha <jsarha@ti.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190326151438.32414-1-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The CS4270 does not by default increment the register address on
consecutive writes. During normal operation it doesn't matter as all
register accesses are done individually. At resume time after suspend,
however, the regcache code gathers the biggest possible block of
registers to sync and sends them one on one go.
To fix this, set the INCR bit in all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We want the video decoder clocks to always round to closest. While the
muxes are already using CLK_MUX_ROUND_CLOSEST, the corresponding
CLK_DIVIDER_ROUND_CLOSEST was forgotten for the dividers.
Fix this by adding the flag to the two vdec dividers.
Fixes: a565242eb9fc ("clk: meson: gxbb: add the video decoder clocks") Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lkml.kernel.org/r/20190319102537.2043-1-mjourdan@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Best to lock across handling the bus error to ensure the DSP doesn't
change power state as we are reading the status registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ASRC turns on, HW will use clk_dac as the reference clock
whether recording or playback.
Both of clk_dac and clk_adc should set proper clock while using ASRC.
Signed-off-by: Shuming Fan <shumingf@realtek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit fbeec965b8d1c ("ASoC: samsung: odroid: Fix 32000 sample rate
handling") the audio root clock frequency is configured improperly for
44100 sample rate. Due to clock rate rounding it's 20070401 Hz instead
of 22579000 Hz. This results in a too low value of the PSR clock divider
in the CPU DAI driver and too fast actual sample rate for fs=44100. E.g.
1 kHz tone has actual 1780 Hz frequency (1 kHz * 20070401/22579000 * 2).
Fix this by increasing the correction passed to clk_set_rate() to take
into account inaccuracy of the EPLL frequency properly.
Fixes: fbeec965b8d1c ("ASoC: samsung: odroid: Fix 32000 sample rate handling") Reported-by: JaeChul Lee <jcsing.lee@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver changes the stream name of DAC and ADC to avoid the issue of
widget with prefixed name. When the machine adds prefixed name for codec,
the stream name of DAI may not find the widgets.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver has two issues when machine add prefix name for codec.
(1)The stream name of DAI can't find the AIF widgets.
(2)The drivr can enable/disalbe the MICBIAS and SAR widgets.
The patch will fix these issues caused by prefixed name added.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If playback and capture are enabled concurrently, when the capture stops
the output becomes inaudile. The playback application will become stuck
and underrun after a timeout.
This is caused by mistaken use of the stream_id, which should only be
set for playback and not for capture
Tested on Apollolake and Kabylake with SST driver.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On HDaudio platforms, if playback is started when capture is working,
there is no audible output.
This can be root-caused to the use of the rx|tx_mask to store an HDaudio
stream tag.
If capture is stared before playback, rx_mask would be non-zero on HDaudio
platform, then the channel number of playback, which is in the same codec
dai with the capture, would be changed by soc_pcm_codec_params_fixup based
on the tx_mask at first, then overwritten by this function based on rx_mask
at last.
According to the author of tx|rx_mask, tx_mask is for playback and rx_mask
is for capture. And stream direction is checked at all other references of
tx|rx_mask in ASoC, so here should be an error. This patch checks stream
direction for tx|rx_mask for fixup function.
This issue would affect not only HDaudio+ASoC, but also I2S codecs if the
channel number based on rx_mask is not equal to the one for tx_mask. It could
be rarely reproduecd because most drivers in kernel set the same channel number
to tx|rx_mask or rx_mask is zero.
Tested on all platforms using stream_tag & HDaudio and intel I2S platforms.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the S/PDIF DAI, there is no requirement to call
snd_soc_dai_set_fmt() as there is no DAI format definition that defines
S/PDIF. In any case, S/PDIF does not have separate clocks, this is
embedded into the data stream.
Consequently, when attempting to use TDA998x in S/PDIF mode, the attempt
to configure TDA998x via the hw_params callback fails as the
hdmi_codec_daifmt is left initialised to zero.
Since the S/PDIF DAI will only be used by S/PDIF, prepare the
hdmi_codec_daifmt structure for this format.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a bug that prevents freeing the reset gpio on unloading
the module.
aic3x_i2c_probe is called when loading the module and it calls list_add
with a probably uninitialized list entry aic3x->list (next = prev = NULL)).
So even if list_del is called it does nothing and in the end the gpio_reset
is not freed. Then a repeated module probing fails silently because
gpio_request fails.
When moving INIT_LIST_HEAD to aic3x_i2c_probe we also have to move
list_del to aic3x_i2c_remove because aic3x_remove may be called
multiple times without aic3x_i2c_remove being called which leads to
a NULL pointer dereference.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since moving the message buffers off the stack, the dynamically
allocated get-prop-descriptor request buffer is incorrectly sized due to
using the pointer rather than request-struct size when creating the
operation.
Fortunately, the pointer size is always larger than this one-byte
request, but this could still cause trouble on the remote end due to the
unexpected message size.
Fixes: 9d15134d067e ("greybus: power_supply: rework get descriptors") Cc: stable <stable@vger.kernel.org> # 4.9 Cc: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building lib/ubsan.c with gcc-9 results in a ton of nasty warnings like
this one:
lib/ubsan.c warning: conflicting types for built-in function
‘__ubsan_handle_negate_overflow’; expected ‘void(void *, void *)’ [-Wbuiltin-declaration-mismatch]
The kernel's declarations of __ubsan_handle_*() often uses 'unsigned
long' types in parameters while GCC these parameters as 'void *' types,
hence the mismatch.
Fix this by using 'void *' to match GCC's declarations.
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Guenter Roeck <linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e63614149 ("net: stmmac: use correct DMA buffer size in the RX descriptor") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trigger stop can be called in situations where trigger start failed
and as such it can't be assumed the buffer is already attached to
the compressed stream or a NULL pointer may be dereferenced.
Fixes: 639e5eb3c7d6 ("ASoC: wm_adsp: Correct handling of compressed streams that restart") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commits:
commit f6dd927f34d6 ("[media] media: ov7670: calculate framerate properly for ov7675")
commit 04ee6d92047e ("[media] media: ov7670: add possibility to bypass pll for ov7675")
introduced the ability to bypass PLL multiplier and use input clock (xvclk)
as pixel clock output frequency for ov7675 sensor.
PLL is bypassed using register DBLV[7:6], according to ov7670 and ov7675
sensor manuals. Macros used to set DBLV register seem wrong in the
driver, as their values do not match what reported in the datasheet.
Fix by changing DBLV_* macros to use bits [7:6] and set bits [3:0] to
default 0x0a reserved value (according to datasheets).
While at there, remove a write to DBLV register in
"ov7675_set_framerate()" that over-writes the previous one to the same
register that takes "info->pll_bypass" flag into account instead of setting PLL
multiplier to 4x unconditionally.
And, while at there, since "info->pll_bypass" is only used in
set/get_framerate() functions used by ov7675 only, it is not necessary
to check for the device id at probe time to make sure that when using
ov7670 "info->pll_bypass" is set to false.
I found out (the hard way) that under some .config options (notably L1_CACHE_SHIFT=7)
and compiler combinations this on-stack alignment leads to a 320 byte
stack usage, which then triggers a KASAN stack warning elsewhere.
Using 320 bytes of stack space for a 40 byte structure is ludicrous and
clearly not right.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Nadav Amit <namit@vmware.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 515ab7c41306 ("x86/mm: Align TLB invalidation info") Link: http://lkml.kernel.org/r/20190416080335.GM7905@worktop.programming.kicks-ass.net
[ Minor changelog edits. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unmaps memory inside the .bss when DEBUG_PAGEALLOC=y.
kmemleak_init() will register the .data/.bss sections and then
kmemleak_scan() will scan those addresses and dereference them looking
for pointer references. If free_init_pages() frees and unmaps pages in
those sections, kmemleak_scan() will crash if referencing one of those
addresses:
BUG: unable to handle kernel paging request at ffffffffbd402000
CPU: 12 PID: 325 Comm: kmemleak Not tainted 5.1.0-rc4+ #4
RIP: 0010:scan_block
Call Trace:
scan_gray_list
kmemleak_scan
kmemleak_scan_thread
kthread
ret_from_fork
Since kmemleak_free_part() is tolerant to unknown objects (not tracked
by kmemleak), it is fine to call it from free_init_pages() even if not
all address ranges passed to this function are known to kmemleak.
[ bp: Massage. ]
Fixes: b3f0907c71e0 ("x86/mm: Add .bss..decrypted section to hold shared variables") Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190423165811.36699-1-cai@lca.pw Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel_randomize_memory() uses __PHYSICAL_MASK_SHIFT to calculate
the maximum amount of system RAM supported. The size of the direct
mapping section is obtained from the smaller one of the below two
values:
(actual system RAM size + padding size) vs (max system RAM size supported)
This calculation is wrong since commit
b83ce5ee9147 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52").
In it, __PHYSICAL_MASK_SHIFT was changed to be 52, regardless of whether
the kernel is using 4-level or 5-level page tables. Thus, it will always
use 4 PB as the maximum amount of system RAM, even in 4-level paging
mode where it should actually be 64 TB.
Thus, the size of the direct mapping section will always
be the sum of the actual system RAM size plus the padding size.
Even when the amount of system RAM is 64 TB, the following layout will
still be used. Obviously KALSR will be weakened significantly.
The size of padding region is controlled by
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING, which is 10 TB by default.
The above issue only exists when
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING is set to a non-zero value,
which is the case when CONFIG_MEMORY_HOTPLUG is enabled. Otherwise,
using __PHYSICAL_MASK_SHIFT doesn't affect KASLR.
Fix it by replacing __PHYSICAL_MASK_SHIFT with MAX_PHYSMEM_BITS.
[ bp: Massage commit message. ]
Fixes: b83ce5ee9147 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52") Signed-off-by: Baoquan He <bhe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Thomas Garnier <thgarnie@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: frank.ramsay@hpe.com Cc: herbert@gondor.apana.org.au Cc: kirill@shutemov.name Cc: mike.travis@hpe.com Cc: thgarnie@google.com Cc: x86-ml <x86@kernel.org> Cc: yamada.masahiro@socionext.com Link: https://lkml.kernel.org/r/20190417083536.GE7065@MiWiFi-R3L-srv Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 648e921888ad ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the pmc_plt_clocks of the Bay Trail SoC are
unconditionally gated off. Unfortunately this will break systems where these
clocks are used for external purposes beyond the kernel's knowledge. Fix it
by implementing a system specific quirk to mark the necessary pmc_plt_clks as
critical.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by: David Müller <dave.mueller@gmx.ch> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c7d606f560e4 ("x86/mce: Improve error message when kernel cannot recover")
a case was added for a machine check caused by a DATA access to poison
memory from the kernel. A case should have been added also for an
uncorrectable error during an instruction fetch in the kernel.
Add that extra case so the error message now reads:
mce: [Hardware Error]: Machine check: Instruction fetch error in kernel
Fixes: c7d606f560e4 ("x86/mce: Improve error message when kernel cannot recover") Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Pu Wen <puwen@hygon.cn> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190225205940.15226-1-tony.luck@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing top-down search the low_limit is not PAGE_SIZE but rather
max(PAGE_SIZE, mmap_min_addr). This handle cases in which mmap_min_addr >
PAGE_SIZE.
Fixes: fba2369e6ceb ("mm: use vm_unmapped_area() on powerpc architecture") Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: db3bdcb9c3ff ("mac80211: allow AP_VLAN operation on crypto controlled devices") Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the SECURITY_FS_USE_MNTPOINT case we never want to allow relabeling
files/directories, so we should never set the SBLABEL_MNT flag. The
'special handling' in selinux_is_sblabel_mnt() is only intended for when
the behavior is set to SECURITY_FS_USE_GENFS.
While there, make the logic in selinux_is_sblabel_mnt() more explicit
and add a BUILD_BUG_ON() to make sure that introducing a new
SECURITY_FS_USE_* forces a review of the logic.
Fixes: d5f3a5f6e7e7 ("selinux: add security in-core xattr support for pstore and debugfs") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc1ba24f7fff6 ("SELINUX: Make selinux cache VFS RCU walks safe")
results in no audit messages at all if in permissive mode because the
cache is updated during the rcu walk and thus no denial occurs on
the subsequent ref walk. Fix this by not updating the cache when
performing a non-blocking permission check. This only affects search
and symlink read checks during rcu walk.
Fixes: 0dc1ba24f7fff6 ("SELINUX: Make selinux cache VFS RCU walks safe") Reported-by: BMK <bmktuwien@gmail.com> Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i.MX8MQ platform, clock driver uses platform driver
model and it is probed after GPIO driver, so when GPIO
driver fails to get clock, it should check the error type
to decide whether to return defer probe or just ignore
the clock operation.
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen") Acked-by: Andi Shyti <andi@etezian.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SNVS IRQ is requested before necessary driver data initialized,
if there is a pending IRQ during driver probe phase, kernel
NULL pointer panic will occur in IRQ handler. To avoid such
scenario, just initialize necessary driver data before enabling
IRQ. This patch is inspired by NXP's internal kernel tree.
The open-coded variant missed destroy of SELinux created QP, reuse already
existing ib_detroy_qp() call and use this opportunity to clean
ib_create_qp() from double prints and unclear exit paths.
Reported-by: Parav Pandit <parav@mellanox.com> Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs") Signed-off-by: Yuval Avnery <yuvalav@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MAD agents isn't allowed to manage the subnet, or fails to register
for the LSM notifier, the security context is leaked. Free the context in
these cases.
Fixes: 47a2b338fe63 ("IB/core: Enforce security on management datagrams") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reported-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only Coffeelake should use Cannonlake regmap other than Cannonlake
platform. This allows Coffeelake special handling only when there is no
matching PCI device and default reg map selected as per CPUID is for
Sunrisepoint PCH. This change is needed to enable support for newer SoCs
such as Icelake.
Cc: "David E. Box" <david.e.box@intel.com> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Fixes: 661405bd817b ("platform/x86: intel_pmc_core: Special case for Coffeelake") Acked-by: "David E. Box" <david.e.box@linux.intel.com> Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Cannonlake and Icelake, the IP name for Res_6 should be SPF i.e.
South Port F. No functional change is intended other than just renaming
the IP appropriately.
Previously support was added to allow streams to be stopped and
started again without the DSP being power cycled and this was done
by clearing the buffer state in trigger start. Another supported
use-case is using the DSP for a trigger event then opening the
compressed stream later to receive the audio, unfortunately clearing
the buffer state in trigger start destroys the data received
from such a trigger. Correct this issue by moving the call to
wm_adsp_buffer_clear to be in trigger stop instead.
Fixes: 61fc060c40e6 ("ASoC: wm_adsp: Support streams which can start/stop with DSP active") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 37c7401e8c1f ("ASoC: Intel: bytcr_rt5651: Fix DMIC map
headsetmic mapping"), changed the headsetmic mapping from IN3P to IN2P,
this was based on the observation that all bytcr_rt5651 devices I have
access to (7 devices) where all using IN3P for the headsetmic. This was
an attempt to unifify / simplify the mapping, but it was wrong.
None of those devices was actually using a digital internal mic. Now I've
access to a Point of View TAB-P1006W-232 (v1.0) tabler, which does use a
DMIC and it does have its headsetmic connected to IN2P, showing that the
original mapping was correct, so this commit reverts the change changing
the mapping back to IN2P.
Fixes: 37c7401e8c1f ("ASoC: Intel: bytcr_rt5651: Fix DMIC map ... mapping") Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lsb calculation is not masking the correct bits from the user input.
Subtract 1 from (1 << offset) to correctly set up the mask to be applied
to user input.
The lsb register stores its value starting at the bit 7 position.
adt7316_store_DAC() currently assumes the value is at the other end of the
register. Shift the lsb value before storing it in a new variable lsb_reg,
and write this variable to the lsb register.
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of the current dac value is using the wrong bits of the
dac lsb register. Create two macros to shift the lsb register value into
lsb position, depending on whether the dac is 10 or 12 bit. Initialize
data to 0 so, with an 8 bit dac, the msb register value can be bitwise
ORed with data.
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With adt7516/7/9, internal vref is available for dacs a and b, dacs c and
d, or all dacs. The driver doesn't currently support internal vref for all
dacs. Change the else if to an if so both bits are checked rather than
just one or the other.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore bdev->tx_state with clearing bit BTMTKUART_TX_WAIT_VND_EVT
when there is an error on waiting for the corresponding event.
Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low. This can cause an
interrupt storm in the time between request_irq() and disable_irq().
We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.
Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support") Fixes: 5364a0b4f4be ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new amd_hw_cache_event_ids_f17h assignment structure set
for AMD families 17h and above, since a lot has changed. Specifically:
L1 Data Cache
The data cache access counter remains the same on Family 17h.
For DC misses, PMCx041's definition changes with Family 17h,
so instead we use the L2 cache accesses from L1 data cache
misses counter (PMCx060,umask=0xc8).
For DC hardware prefetch events, Family 17h breaks compatibility
for PMCx067 "Data Prefetcher", so instead, we use PMCx05a "Hardware
Prefetch DC Fills."
L1 Instruction Cache
PMCs 0x80 and 0x81 (32-byte IC fetches and misses) are backward
compatible on Family 17h.
For prefetches, we remove the erroneous PMCx04B assignment which
counts how many software data cache prefetch load instructions were
dispatched.
LL - Last Level Cache
Removing PMCs 7D, 7E, and 7F assignments, as they do not exist
on Family 17h, where the last level cache is L3. L3 counters
can be accessed using the existing AMD Uncore driver.
Data TLB
On Intel machines, data TLB accesses ("dTLB-loads") are assigned
to counters that count load/store instructions retired. This
is inconsistent with instruction TLB accesses, where Intel
implementations report iTLB misses that hit in the STLB.
Ideally, dTLB-loads would count higher level dTLB misses that hit
in lower level TLBs, and dTLB-load-misses would report those
that also missed in those lower-level TLBs, therefore causing
a page table walk. That would be consistent with instruction
TLB operation, remove the redundancy between dTLB-loads and
L1-dcache-loads, and prevent perf from producing artificially
low percentage ratios, i.e. the "0.01%" below:
42,550,869 L1-dcache-loads
41,591,860 dTLB-loads
4,802 dTLB-load-misses # 0.01% of all dTLB cache hits
7,283,682 L1-dcache-stores
7,912,392 dTLB-stores
310 dTLB-store-misses
On AMD Families prior to 17h, the "Data Cache Accesses" counter is
used, which is slightly better than load/store instructions retired,
but still counts in terms of individual load/store operations
instead of TLB operations.
So, for AMD Families 17h and higher, this patch assigns "dTLB-loads"
to a counter for L1 dTLB misses that hit in the L2 dTLB, and
"dTLB-load-misses" to a counter for L1 DTLB misses that caused
L2 DTLB misses and therefore also caused page table walks. This
results in a much more accurate view of data TLB performance:
60,961,781 L1-dcache-loads
4,601 dTLB-loads
963 dTLB-load-misses # 20.93% of all dTLB cache hits
Note that for all AMD families, data loads and stores are combined
in a single accesses counter, so no 'L1-dcache-stores' are reported
separately, and stores are counted with loads in 'L1-dcache-loads'.
Also note that the "% of all dTLB cache hits" string is misleading
because (a) "dTLB cache": although TLBs can be considered caches for
page tables, in this context, it can be misinterpreted as data cache
hits because the figures are similar (at least on Intel), and (b) not
all those loads (technically accesses) technically "hit" at that
hardware level. "% of all dTLB accesses" would be more clear/accurate.
Instruction TLB
On Intel machines, 'iTLB-loads' measure iTLB misses that hit in the
STLB, and 'iTLB-load-misses' measure iTLB misses that also missed in
the STLB and completed a page table walk.
For AMD Family 17h and above, for 'iTLB-loads' we replace the
erroneous instruction cache fetches counter with PMCx084
"L1 ITLB Miss, L2 ITLB Hit".
For 'iTLB-load-misses' we still use PMCx085 "L1 ITLB Miss,
L2 ITLB Miss", but set a 0xff umask because without it the event
does not get counted.
Branch Predictor (BPU)
PMCs 0xc2 and 0xc3 continue to be valid across all AMD Families.
Node Level Events
Family 17h does not have a PMCx0e9 counter, and corresponding counters
have not been made available publicly, so for now, we mark them as
unsupported for Families 17h and above.
Reference:
"Open-Source Register Reference For AMD Family 17h Processors Models 00h-2Fh"
Released 7/17/2018, Publication #56255, Revision 3.03:
https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
[ mingo: tidied up the line breaks. ] Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: <stable@vger.kernel.org> # v4.9+ Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Liška <mliska@suse.cz> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Pu Wen <puwen@hygon.cn> Cc: Stephane Eranian <eranian@google.com> Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Lendacky <Thomas.Lendacky@amd.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: linux-kernel@vger.kernel.org Cc: linux-perf-users@vger.kernel.org Fixes: e40ed1542dd7 ("perf/x86: Add perf support for AMD family-17h processors") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting flush_work() warning caused by commit 4d43d395fed12463
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
projects / linux-stable / log