The quiesce function calls cio_cancel_halt_clear() and if we
get an -EBUSY we go into a loop where we:
- wait for any interrupts
- flush all I/O in the workqueue
- retry cio_cancel_halt_clear
During the period where we are waiting for interrupts or
flushing all I/O, the channel subsystem could have completed
a halt/clear action and turned off the corresponding activity
control bits in the subchannel status word. This means the next
time we call cio_cancel_halt_clear(), we will again start by
calling cancel subchannel and so we can be stuck between calling
cancel and halt forever.
Rather than calling cio_cancel_halt_clear() immediately after
waiting, let's try to disable the subchannel. If we succeed in
disabling the subchannel then we know nothing else can happen
with the device.
Suggested-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <4d5a4b98ab1b41ac6131b5c36de18b76c5d66898.1555449329.git.alifm@linux.ibm.com> Reviewed-by: Eric Farman <farman@linux.ibm.com> Acked-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current calculation for the video start delay in the current DSI driver
is that it is the total vertical size, minus the front porch and sync length,
plus 1. This equals to the active vertical size plus the back porch plus 1.
That 1 is coming in the Allwinner BSP from an variable that is set to 1.
However, if we look at the Allwinner BSP more closely, and especially in
the "legacy" code for the display (in drivers/video/sunxi/legacy/), we can
see that this variable is actually computed from the porches and the sync
minus 10, clamped between 8 and 100.
This fixes the start delay symptom we've seen on some panels (vblank
timeouts with vertical white stripes at the bottom of the panel).
After an event is sent, we try to copy it into the user buffer of the
first waiter in drm_read() and if the user buffer doesn't have enough
room we put it back onto the list. However, we didn't wake up any
subsequent waiter, so that event may sit on the list until either a new
vblank event is sent or a new waiter appears. Rare, but in the worst
case may lead to a stuck process.
Building with clang shows a variable that is only used by the
suspend/resume functions but defined outside of their #ifdef block:
sound/soc/ti/davinci-mcasp.c:48:12: error: variable 'context_regs' is not needed and will not be emitted
We commonly fix these by marking the PM functions as __maybe_unused,
but here that would grow the davinci_mcasp structure, so instead
add another #ifdef here.
Fixes: 1cc0c054f380 ("ASoC: davinci-mcasp: Convert the context save/restore to use array") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 71abd29057cb ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer. In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.
However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.
Change it to empty the FIFO and throw away the data. Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.
There is another issue, which affects master mode when switching from
DMA to PIO. There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner. I don't know
why this data is unexpectedly in the FIFO. It's likely there is a
different bug or erratum responsible for that. But regardless of that,
I think this is proper fix the for bug at hand here.
Fixes: 71abd29057cb ("spi: imx: Add support for SPI Slave mode") Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the sequencer is reset after each SPI message since commit 880c6d114fd79a69 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac4b8837 ("spi: add support for Renesas RSPI") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently dsi_display_init_dsi() calls dss_pll_enable() but it is not
paired with dss_pll_disable() in dsi_display_uninit_dsi(). This leaves
the DSS clocks enabled when the display is blanked wasting about extra
5mW of power while idle.
The clock that is left on by not calling dss_pll_disable() is
DSS_CLKCTRL bit 10 OPTFCLKEN_SYS_CLK that is the source clock for
DSI PLL.
We can fix this issue by by making the current dsi_pll_uninit() into
dsi_pll_disable(). This way we can just call dss_pll_disable() from
dsi_display_uninit_dsi() and the code becomes a bit easier to follow.
However, we need to also consider that DSI PLL can be muxed for DVI too
as pointed out by Tomi Valkeinen <tomi.valkeinen@ti.com>. In the DVI
case, we want to unconditionally disable the clocks. To get around this
issue, we separate out the DSI lane handling from dsi_pll_enable() and
dsi_pll_disable() as suggested by Tomi in an earlier experimental patch.
So we must only toggle the DSI regulator based on the vdds_dsi_enabled
flag from dsi_display_init_dsi() and dsi_display_uninit_dsi().
We need to make these two changes together to avoid breaking things
for DVI when fixing the DSI clock handling. And this all causes a
slight renumbering of the error path for dsi_display_init_dsi().
Suggested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further,
these buffers are used without a check. The patch checks for these
failures and sends the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
When streaming is stopped all URBs are killed, but in fill_frame and in
bulk_irq this results in an attempt to resubmit the killed URB. That is
not what you want and causes spurious kernel messages.
So check if streaming has stopped before resubmitting.
Also check against gspca_dev->streaming rather than vb2_start_streaming_called()
since vb2_start_streaming_called() will return true when in stop_streaming,
but gspca_dev->streaming is set to false when stop_streaming is called.
Fixes: 6992effe5344 ("gspca: Kill all URBs before releasing any of them") Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver should really call dm365_isif_setup_pinmux() through a callback,
but uses a hack to include a davinci specific machine header file when
compile testing instead. This works almost everywhere, but not on the
ARM omap1 platform, which has another header named mach/mux.h. This
causes a build failure:
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: implicit declaration of function 'davinci_cfg_reg' [-Werror,-Wimplicit-function-declaration]
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:18: error: use of undeclared identifier 'DM365_VIN_CAM_WEN'
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2029:18: error: use of undeclared identifier 'DM365_VIN_CAM_VD'
davinci_cfg_reg(DM365_VIN_CAM_VD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2030:18: error: use of undeclared identifier 'DM365_VIN_CAM_HD'
davinci_cfg_reg(DM365_VIN_CAM_HD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2031:18: error: use of undeclared identifier 'DM365_VIN_YIN4_7_EN'
davinci_cfg_reg(DM365_VIN_YIN4_7_EN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2032:18: error: use of undeclared identifier 'DM365_VIN_YIN0_3_EN'
davinci_cfg_reg(DM365_VIN_YIN0_3_EN);
^
7 errors generated.
Exclude omap1 from compile-testing, under the assumption that all others
still work.
Fixes: 4907c73deefe ("media: staging: davinci_vpfe: allow building with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 14f4eaeddabc ("media: dvbsky: fix driver unregister logic") fixed
a use-after-free by removing the reference to the frontend after deleting
the backing i2c device.
This has the unfortunate side effect the frontend device is never freed
in the dvb core leaving a dangling device, leading to errors when the
dvb core tries to register the frontend after e.g. a replug as reported
here: https://www.spinics.net/lists/linux-media/msg138181.html
The use after free happened as dvb_usbv2_disconnect calls in this order:
- dvb_usb_device::props->exit(...)
- dvb_usbv2_adapter_frontend_exit(...)
+ if (fe) dvb_unregister_frontend(fe)
+ dvb_usb_device::props->frontend_detach(...)
Moving the release of the i2c device from exit() to frontend_detach()
avoids the dangling pointer access and allows the core to unregister
the frontend.
This was originally reported for a DVBSky T680CI, but it also affects
the MyGica T230C. As all supported devices structure the registration/
unregistration identically, apply the change for all device types.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
si2165_readreg8() may fail. Looking into si2165_readreg8(), we will find
that "val_tmp" will be an uninitialized value when regmap_read() fails.
"val_tmp" is then assigned to "val". So if si2165_readreg8() fails,
"val" will be a random value. Further use will lead to undefined
behaviors. The fix checks if si2165_readreg8() fails, and if so, returns
its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Matthias Schwarzott <zzam@gentoo.org> Tested-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing planes should not release the 2nd odm pipe right away,
this change leaves us with 2 pipes with null planes and same stream
when planes are released during odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
In enumerate_services, ida_simple_get on failure can return an error and
leaks memory. The patch ensures that the dev_set_name is set on non
failure cases, and releases memory during failure.
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Currently incoming ARP Replies, for example via a DHT-PUT message, do
not update the timeout for an already existing DAT entry. These ARP
Replies are dropped instead.
This however defeats the purpose of the DHCPACK snooping, for instance.
Right now, a DAT entry in the DHT will be purged every five minutes,
likely leading to a mesh-wide ARP Request broadcast after this timeout.
Which then recreates the entry. The idea of the DHCPACK snooping is to
be able to update an entry before a timeout happens, to avoid ARP Request
flooding.
This patch fixes this issue by updating a DAT entry on incoming
ARP Replies even if a matching DAT entry already exists. While still
filtering the ARP Reply towards the soft-interface, to avoid duplicate
messages on the client device side.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang correctly points out a code path that would lead
to an uninitialized variable use:
security/selinux/netlabel.c:310:6: error: variable 'addr' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:322:40: note: uninitialized use occurs here
rc = netlbl_conn_setattr(ep->base.sk, addr, &secattr);
^~~~
security/selinux/netlabel.c:310:2: note: remove the 'if' if its condition is always true
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:291:23: note: initialize the variable 'addr' to silence this warning
struct sockaddr *addr;
^
= NULL
This is probably harmless since we should not see ipv6 packets
of CONFIG_IPV6 is disabled, but it's better to rearrange the code
so this cannot happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[PM: removed old patchwork link, fixed checkpatch.pl style errors] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c215978 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcuperf.perf_type is not in the rcu_perf_init()
function's perf_ops[] array, rcuperf prints some console messages and
then invokes rcu_perf_cleanup() to set state so that a future torture
test can run. However, rcu_perf_cleanup() also attempts to end the
test that didn't actually start, and in doing so relies on the value
of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case and
inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding
relying on an irrelevant cur_ops value.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linux reads MCG_CAP[Count] to find the number of MCA banks visible to a
CPU. Currently, this number is the same for all CPUs and a warning is
shown if there is a difference. The number of banks is overwritten with
the MCG_CAP[Count] value of each following CPU that boots.
According to the Intel SDM and AMD APM, the MCG_CAP[Count] value gives
the number of banks that are available to a "processor implementation".
The AMD BKDGs/PPRs further clarify that this value is per core. This
value has historically been the same for every core in the system, but
that is not an architectural requirement.
Future AMD systems may have different MCG_CAP[Count] values per core,
so the assumption that all CPUs will have the same MCG_CAP[Count] value
will no longer be valid.
Also, the first CPU to boot will allocate the struct mce_banks[] array
using the number of banks based on its MCG_CAP[Count] value. The machine
check handler and other functions use the global number of banks to
iterate and index into the mce_banks[] array. So it's possible to use an
out-of-bounds index on an asymmetric system where a following CPU sees a
MCG_CAP[Count] value greater than its predecessors.
Thus, allocate the mce_banks[] array to the maximum number of banks.
This will avoid the potential out-of-bounds index since the value of
mca_cfg.banks is capped to MAX_NR_BANKS.
Set the value of mca_cfg.banks equal to the max of the previous value
and the value for the current CPU. This way mca_cfg.banks will always
represent the max number of banks detected on any CPU in the system.
This will ensure that all CPUs will access all the banks that are
visible to them. A CPU that can access fewer than the max number of
banks will find the registers of the extra banks to be read-as-zero.
Furthermore, print the resulting number of MCA banks in use. Do this in
mcheck_late_init() so that the final value is printed after all CPUs
have been initialized.
Finally, get bank count from target CPU when doing injection with mce-inject
module.
[ bp: Remove out-of-bounds example, passify and cleanup commit message. ]
If the specified rcutorture.torture_type is not in the rcu_torture_init()
function's torture_ops[] array, rcutorture prints some console messages
and then invokes rcu_torture_cleanup() to set state so that a future
torture test can run. However, rcu_torture_cleanup() also attempts to
end the test that didn't actually start, and in doing so relies on the
value of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case
and inserts a check near the beginning of rcu_torture_cleanup(),
thus avoiding relying on an irrelevant cur_ops value.
Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0ee8f ("x86, mce: implement new status bits") Reported-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk Signed-off-by: Sasha Levin <sashal@kernel.org>
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
Fixes the following crash as the return was missing from the check if an
fcport is offloaded. If we hit this code we continue to try to post an
invalid task which can lead to the crash:
Several people reported testing failures after setting CLOCK_REALTIME close
to the limits of the kernel internal representation in nanoseconds,
i.e. year 2262.
The failures are exposed in subsequent operations, i.e. when arming timers
or when the advancing CLOCK_MONOTONIC makes the calculation of
CLOCK_REALTIME overflow into negative space.
Now people start to paper over the underlying problem by clamping
calculations to the valid range, but that's just wrong because such
workarounds will prevent detection of real issues as well.
It is reasonable to force an upper bound for the various methods of setting
CLOCK_REALTIME. Year 2262 is the absolute upper bound. Assume a maximum
uptime of 30 years which is plenty enough even for esoteric embedded
systems. That results in an upper bound of year 2232 for setting the time.
Once that limit is reached in reality this limit is only a small part of
the problem space. But until then this stops people from trying to paper
over the problem at the wrong places.
Reported-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Reported-by: Hongbo Yao <yaohongbo@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903231125480.2157@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
38ac0287b7f4 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB")
efifb_probe() checks its memory range via efi_mem_desc_lookup(),
and this leads to a spurious error message:
EFI_MEMMAP is not enabled
at every boot on KVM. This is quite annoying since the error message
appears even if you set "quiet" boot option.
Since this happens on legacy boot, which strangely enough exposes
a EFI framebuffer via screen_info, let's double check that we are
doing an EFI boot before attempting to access the EFI memory map.
Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20190328193429.21373-3-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is hitting use-after-free bug in uinput module [1]. This is because
kobject_uevent(KOBJ_REMOVE) is called again due to commit 0f4dafc0563c6c49
("Kobject: auto-cleanup on final unref") after memory allocation fault
injection made kobject_uevent(KOBJ_REMOVE) from device_del() from
input_unregister_device() fail, while uinput_destroy_device() is expecting
that kobject_uevent(KOBJ_REMOVE) is not called after device_del() from
input_unregister_device() completed.
That commit intended to catch cases where nobody even attempted to send
"remove" uevents. But there is no guarantee that an event will ultimately
be sent. We are at the point of no return as far as the rest of the kernel
is concerned; there are no repeats or do-overs.
Also, it is not clear whether some subsystem depends on that commit.
If no subsystem depends on that commit, it will be better to remove
the state_{add,remove}_uevent_sent logic. But we don't want to risk
a regression (in a patch which will be backported) by trying to remove
that logic. Therefore, as a first step, let's avoid the use-after-free bug
by making sure that kobject_uevent(KOBJ_REMOVE) won't be triggered twice.
According to hidpp20_batterylevel_get_battery_info my Logitech K270
keyboard reports only 2 battery levels. This matches with what I've seen
after testing with batteries at varying level of fullness, it always
reports either 5% or 30%.
Windows reports "battery good" for the 30% level. I've captured an USB
trace of Windows reading the battery and it is getting the same info
as the Linux hidpp code gets.
Now that Linux handles these devices as hidpp devices, it reports the
battery as being low as it treats anything under 31% as low, this leads
to the user constantly getting a "Keyboard battery is low" warning from
GNOME3, which is very annoying.
This commit fixes this by changing the low threshold to anything under
30%, which I assume is what Windows does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As seen on some USB wireless keyboards manufactured by Primax, the HID
parser was using some assumptions that are not always true. In this case
it's s the fact that, inside the scope of a main item, an Usage Page
will always precede an Usage.
The spec is not pretty clear as 6.2.2.7 states "Any usage that follows
is interpreted as a Usage ID and concatenated with the Usage Page".
While 6.2.2.8 states "When the parser encounters a main item it
concatenates the last declared Usage Page with a Usage to form a
complete usage value." Being somewhat contradictory it was decided to
match Window's implementation, which follows 6.2.2.8.
In summary, the patch moves the Usage Page concatenation from the local
item parsing function to the main item parsing function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Terry Junge <terry.junge@poly.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/sh/include/cpu-sh4/cpu/sh7786.h: In function ‘sh7786_mm_sel’:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:21: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [-Wint-conversion]
return __raw_readl(0xFC400020) & 0x7;
^~~~~~~~~~
In file included from include/linux/io.h:25:0,
from arch/sh/include/cpu-sh4/cpu/sh7786.h:14,
from drivers/pinctrl/sh-pfc/pfc-sh7786.c:15:
arch/arm/include/asm/io.h:113:21: note: expected ‘const volatile void *’ but argument is of type ‘unsigned int’
#define __raw_readl __raw_readl
^
arch/arm/include/asm/io.h:114:19: note: in expansion of macro ‘__raw_readl’
static inline u32 __raw_readl(const volatile void __iomem *addr)
^~~~~~~~~~~
__raw_readl() on SuperH is a macro that casts the passed I/O address to
the correct type, while the implementations on most other architectures
expect to be passed the correct pointer type.
Add an explicit cast to fix this.
Note that this also gets rid of a sparse warning on SuperH:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: warning: incorrect type in argument 1 (different base types)
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: expected void const volatile [noderef] <asn:2>*<noident>
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: got unsigned int
port_pd is treated as le32 in declaration and read, fix assignment to be
in le32 too. This change fixes the following compilation warnings.
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: warning: incorrect type
in assignment (different base types)
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: expected restricted __le32 [usertype] port_pd
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: got restricted __be32 [usertype]
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Gal Pressman <galpress@amazon.com> Reviewed-by: Lijun Ou <ouliun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionally GCC is less agressive with inlining and the following is
observed:
arch/x86/kernel/signal.o: warning: objtool: restore_sigcontext()+0x3cc: call to force_valid_ss.isra.5() with UACCESS enabled
arch/x86/kernel/signal.o: warning: objtool: do_signal()+0x384: call to frame_uc_flags.isra.0() with UACCESS enabled
Cure this by moving this code out of the AC=1 region, since it really
isn't needed for the user access.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The functions that send management TX frame have 3 possible
results: success and other side acknowledged receive (ACK=1),
success and other side did not acknowledge receive(ACK=0) and
failure to send the frame. The current implementation
incorrectly reports the ACK=0 case as failure.
Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm64/kernel/cpu_ops.c:102:1-7: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 69, but
without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the end of initialization, a delay is required by the panel. Without
this delay, the panel could received a frame early & generate a crash of
panel (black screen).
For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.
In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.
Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.
However improper values shall be fixed to avoid potential bugs. Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Fix a race which leads to an Oops with NULL pointer dereference. The
dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get
net_device structure of interface with index 0 via if2bss mapping. This
shouldn't fail because of check for bus being ready in brcmf_netdev_open(),
but it's not synchronised with USB disconnect and there is a race: after
the check the bus can be marked down and the mapping for interface 0 may be
gone.
Solve this by modifying disconnect handling so that the removal of mapping
of ifidx to brcmf_if structure happens after netdev removal (which is
synchronous with brcmf_netdev_open() thanks to rtln being locked in
devinet_ioctl()). This assures brcmf_netdev_open() returns before the
mapping is removed during disconnect.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff
which is part of any queue. After USB disconnect this may have happened
when brcmf_fws_hanger_cleanup() is called as per-interface psq was never
cleaned when removing the interface.
Change brcmf_fws_macdesc_cleanup() in a way that it removes the
corresponding packets from hanger table (to avoid double-free when
brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the
interface specific packet queue.
Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle
running in AP mode. This was reproducible when the interface was
transmitting during the disconnect and is fixed with this commit.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40
Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core
CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14)
[<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c)
[<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114)
[<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48)
[<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40)
[<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c)
[<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68)
[<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150)
[<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0)
[<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c)
[<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0)
[<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec)
[<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8)
[<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308)
[<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8)
[<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8)
[<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50)
[<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8)
[<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554)
[<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154)
[<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xecf8dfb0 to 0xecf8dff8)
dfa0: 00000000000000000000000000000000
dfc0: 0000000000000000000000000000000000000000000000000000000000000000
dfe0: 000000000000000000000000000000000000001300000000
---[ end trace 38d234018e9e2a90 ]---
------------[ cut here ]------------
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when
kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion
which silences those warnings and improves code readability.
Fix below errors when connecting the USB WiFi dongle:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2
BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434
last function: hub_event
1 lock held by kworker/0:2/434:
#0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14)
[<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4)
[<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808)
[<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xed1d9fb0 to 0xed1d9ff8)
9fa0: 00000000000000000000000000000000
9fc0: 0000000000000000000000000000000000000000000000000000000000000000
9fe0: 000000000000000000000000000000000000001300000000
======================================================
WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted
------------------------------------------------------
kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808
but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns about what is clearly a case of passing an uninitalized
variable into a static function:
drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here
[-Werror,-Wuninitialized]
lpphy_papd_cal(dev, gains, 0, 1, 30);
^~~~~
drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here
struct lpphy_tx_gains gains, oldgains;
^
1 error generated.
However, this function is empty, and its arguments are never evaluated,
so gcc in contrast does not warn here. Both compilers behave in a
reasonable way as far as I can tell, so we should change the code
to avoid the warning everywhere.
We could just eliminate the lpphy_papd_cal() function entirely,
given that it has had the TODO comment in it for 10 years now
and is rather unlikely to ever get done. I'm doing a simpler
change here, and just pass the 'oldgains' variable in that has
been initialized, based on the guess that this is what was
originally meant.
Fixes: 2c0d6100da3e ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, ksym_search located at trace_helpers won't check symbols are
existing or not.
In ksym_search, when symbol is not found, it will return &syms[0](_stext).
But when the kernel symbols are not loaded, it will return NULL, which is
not a desired action.
This commit will add verification logic whether symbols are loaded prior
to the symbol search.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Indio->mlock is used for protecting the different iio device modes.
It is currently not being used in this way. Replace the lock with
an internal lock specifically used for protecting the SPI transfer
buffer.
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable
'calculated_time' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
While it isn't wrong, this will never be a problem because
iio_push_to_buffers_with_timestamp only uses calculated_time
on the same condition that it is assigned (when scan_timestamp
is not zero). While iio_push_to_buffers_with_timestamp is marked
as inline, Clang does inlining in the optimization stage, which
happens after the semantic analysis phase (plus inline is merely
a hint to the compiler).
Fix this by just zero initializing calculated_time.
Link: https://github.com/ClangBuiltLinux/linux/issues/394 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_find_matching_node_and_match returns a node pointer with
refcount incremented thus it must be explicitly decremented after the
last usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/pl111/pl111_versatile.c:333:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:340:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:346:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:354:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
drivers/gpu/drm/pl111/pl111_versatile.c:402:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVER FOR ARM PL111 CLCD) Cc: David Airlie <airlied@linux.ie> (maintainer:DRM DRIVERS) Cc: Daniel Vetter <daniel@ffwll.ch> (maintainer:DRM DRIVERS) Cc: dri-devel@lists.freedesktop.org (open list:DRM DRIVERS) Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/1554307455-40361-6-git-send-email-wen.yang99@zte.com.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
The LLVM linker (ld.lld) defaults to removing local relocations, which
causes KASLR boot failures. ld.bfd and ld.gold already handle this
correctly. This adds the explicit instruction "--discard-none" during
the link phase. There is no change in output for ld.bfd and ld.gold,
but ld.lld now produces an image with all the needed relocations.
The implementation of IOC_OPAL_ENABLE_DISABLE_MBR handled the value
opal_mbr_data.enable_disable incorrectly: enable_disable is expected
to be one of OPAL_MBR_ENABLE(0) or OPAL_MBR_DISABLE(1). enable_disable
was passed directly to set_mbr_done and set_mbr_enable_disable where
is was interpreted as either OPAL_TRUE(1) or OPAL_FALSE(0). The end
result was that calling IOC_OPAL_ENABLE_DISABLE_MBR with OPAL_MBR_ENABLE
actually disabled the shadow MBR and vice versa.
This patch adds correct conversion from OPAL_MBR_DISABLE/ENABLE to
OPAL_FALSE/TRUE. The change affects existing programs using
IOC_OPAL_ENABLE_DISABLE_MBR but this is typically used only once when
setting up an Opal drive.
Acked-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Scott Bauer <sbauer@plzdonthack.me> Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/kirkwood-cpufreq.c:127:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
./drivers/cpufreq/kirkwood-cpufreq.c:133:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
and also do some cleanup:
- of_node_put(np);
- np = NULL;
...
of_node_put(np);
The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-pm@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.
Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.
Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.
Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log